Lecture 4. Lab 8 Check valve and pilot-operated check valves Lab 9 Flow divider. Update: Identifying lab objectives Review: Metering/Bleed-off

Size: px
Start display at page:

Download "Lecture 4. Lab 8 Check valve and pilot-operated check valves Lab 9 Flow divider. Update: Identifying lab objectives Review: Metering/Bleed-off"

Transcription

1 98 Lecture 4 Labs coming week: Lab 8 Check valve and pilot-operated check valves Lab 9 Flow divider Update: Identifying lab objectives Review: Metering/Bleed-off (More) efficient circuits? Check and Pilot-to-Open-Check Flow divider Cartridge valves Properties of Hydraulic Fluids Viscosity friction and leakage Bulk modulus and Inertance (next week)

2 99 Control Circuit Efficiency Where are energy lost? More efficiency circuits? Displacement control Pulse-width-modulation Transformers Electrohydraulic- Actuator (EHA)

3 100 More efficient circuits Main goal: Avoid throttling losses in valves (active research) Displacement control (pump control) Hydraulic transformers Common pressure rail Electro-hydraulic actuator Pulse-width modulation

4 101 PWM - Throttle-less control Achieve throttle-less control through on/off control Create the hydraulic analog of a DC-DC Converter Controlled using Pulse-Width-Modulation (PWM) Many different architectures are possible (motor, pump, hydrostat, transformer) Low PQ losses in both on an off state, but PWM leads to a ripple on the output

5 Self-Spinning Rotary PWM Valve 102 H. Tu, M. B. Rannow, M. Wang, P. Y. Li, and T. R. Chase, Design, Modeling and Validation of a High-Speed Rotary PWM On/Off Valve for Use in Virtually Variable Displacement Pumps, ASME Journal of Dynamics Systems, Measurement and Control, Vol , #061002, Nov, P I II L T

6 103 Allows flow only one direction one way directional control valve Check Valves ANSI symbol? Main uses are: by-pass components cylinder locking look mom. No hands!

7 Pilot Operated (open) Check Valves 104 Allows reverse flow when pilot pressure is turned on Enables cylinder locking and to retract cylinder when intended Consider force balance to calculate what pressures needed to open the check Check valve area ratio

8 105 Pilot-to-Open Check Valve Area Ratios Acap Apiston Fload A2 A1 Under no load condition, when can the actuator retract? (Hint: force balance on actuator piston). What if Fload is not zero?

9 106 When will the POC open to reverse flow? Needle 1 Needle 2 P1 Pp Suppose PO check valve area ratio is 3:1 Needle valves: K2 given Find K1 so that PO check opens Pressure divider circuit

10 Cartridge Valves 107 Integrate circuits with many components using a manifold Manifold = aluminum block with internal passages Standard configurations

11 108 Flow Divider Valve Maintain same flow ratio (of 1 in the case) Q left =Q right despite different pressures Identify flow measurement sensors What happens when Q left > Q right? What happens when Q right > Q left? When does equilibrium occur? Some valves are flow combiner/divider? Can this one combine flow?

12 109 Modeling and Analysis of Flow Divider Q a = Q b +Q c Q b = C 1 (x)*sqrt(p a -P b ) Q c = C 2 (x)*sqrt(p a -P c ) P 1 = P a -(Q b /C 1 (x)) 2 P 2 = P a -(Q c /C 2 (x)) 2 Adjust x based on P 1 and P 2

13 110 Cartridge valves Screw-in types (smaller flow rates, single unit) [as in lab] Single valve performs the intended function screws into cavities in manifold cavities are generally common Read on your own Slip-in type (larger flow rates) essentially a check valve versatile functions accomplished by different covers that provide for additional circuits. Area ratio plays key role in the operation

14 111 Screw-in Cartridge Valve Single piece implements the function Plugs into standard manifold porting manifold itself being custom built

15 112 Fluid Properties Viscosity Bulk modulus Inertance

16 A (fake) Car Talk Puzzle 113 You discovered that on your garage floor that your car is leaking oil. You took it in to the mechanic Joe. Joe was busy, so you had to leave the car at the shop s parking lot for the night. Next morning, Joe took your car into the shop and examined the car for leaks, and found nothing. You took your back home, but lo and behold, the car leaked again on your garage floor. Neither you nor Joe is delusional. What is going on?

17 114 Hydraulic Fluid in Fluid Power Systems Primary role is POWER TRANSMISSION Secondary roles Lubrication Enables moving parts prevents wear, metal/metal contact Load carrying ability parts spot welded together if lubrication film breaks down or too thin Sealing leaks Dimensional clearance may induce leak Certain property of fluid may prevent leak (viscosity) Heat transfer / cooling transfer of heat from work area to reservoir / heat exchanger some fluid properties may vary with temperature

18 115 From: M. Radhakrishnan, Hydraulic Fluids ASME Press

19 Some fluid properties 116 Dynamic Viscosity N-s/(m 2 ) = Pa - s = sec * kg m/sec ^2/m = kg / (m sec) = 10 poise µ = τ v / y Kinematic Viscosity Easy to measure. If density = 1000kg/m 3, Shear (N / m 2 ) Tangential speed gradient (1/sec) 1 poise = 10-1 kg /m/s = 0.1 Pa-s 1 cp = centipoise = 1g/m/s = Pa-s µ = 3.78 cp υ = 3.78 cst Updated: Spring 2015 υ = µ ρ y Shear force v (y) No shear when there is no velocity gradient normal to flow Density (kg/m 3 ) m 2 /sec = stoke 1 stoke (St) = cm 2 /sec 1 centi-stoke (cst) =0.01 St 1cSt = 10-6 m 2 /sec

20 117 SAE 40 Viscosity decreases with temperature 15 cs at 100degC (212F) 150 cs at 40degC (104F) SAE 10W 4 cs at 100 deg C(212F) 20 cs at 40 degc (104F) Usually data is given at two temperatures use linear interpolation to find intermediate values 5 to 10 times variation with 60degC variation! Water has much lower viscosity than hydraulic oil Which one for winter or for summer? Water: ~1cS for wide range of temperature! (good!!)

21 High V-I Fluids 118 Viscosity Index (VI): measures temperature dependence of viscosity Modified using chemical additives High VI = low temperature dependence Low VI = large temperature dependence VI index is a measure of this slope! ( Defined relative to 2 standard fluids : VI=0, and VI=100 )

22 119 High viscosity Viscosity is a compromise reduce leak (better sealing) lower chance of oil break down parts spot welded to each other requires larger pressure to sustain flow (sluggish) pump may cavitate (air getting into system) oil / air separation difficult Low viscosity lower drag better efficiency possibility of thin film break down worse leakage (water hydraulics)

23 120 Dynamic viscosity = 45 cp Diameter of pipe D = 0.05m Length of pipe L = 1 m Velocity at y = 0.5cm is 5m/s Velocity at y = 0cm is 0m/s Example v y Find a) shear drag on and b) pressure drop across the pipe Assume linear velocity profile shear = 45cP * (0.001 Pa-sec/cP) * (5m/s / 0.005m) = (N/m 2 )*sec * 1000/sec = 45 N/m 2 Drag force = 45 * pi * D * L = 7.06 N Pressure drop = Drag force / Area = 45*4*L/D = 3.6 kpa = bar

24 Darcy laws: ΔP = Resistance in Pipes and Hoses f (Re) L ρv D 2 2 = f (Re) L D 8ρQ 2 π D 2 4 speed Re = vd v 121 Laminar: (Hagen-Poiseuille) f=64/re Δ 128µ L πd P = 4 Q Re < 2000 Kinematic viscosity Inertia versus viscous Turbulent Smooth pipe ΔP = / Re 1/ 4 L 8 ρq 2 D π D > Re > 4000

25 Friction Factor Moody Diagram 122

26 Example: 3MW Wind Turbine, 35MPa 123

27 Loss in Connectors 124 K-factor K factors ρv ΔP = K 2 Tee s deg elbow deg elbow 0.75 Ball check valve 4.0 Return bend 2.2 Example: Elbow Q = 15gpm, Pressure drop = 0.6psi Q = 37.5gpm, Pressure drop = 4psi 2 v = (outlet) velocity [m/sec] g = gravity const [m/sec^2] Note: K is unit-less and independent of units ΔP Equivalent formula: ρg 2 v H L = K 2g = H L 2 v = K 2g H L = head loss [m]

28 125 Leakage Leakage flow Q = 3 a w 12µ L ΔP P2 Example: a spool in a sleeve w = pi * D (circumference) L = length of land a Q L a = clearance P1 w Note high viscosity decreases leaks

29 126 Example L clearance = 0.1mm Cylindrical Spool P 90 deg elbow diameter = 0.5cm Sleeve Q = 30 LPM?1: Assuming small leakage, determine pressure P.?2: How long does L have to be for leakage to be less than 0.01% of the flow?

30 127 Efficiency vs Viscosity vs Temperature For hydraulic components (e.g. pumps, motors, actuators) with moving parts, there is always a trade-off between Volumetric efficiency [leakage] Mechanical Efficiency [friction] Total efficiencies for pumps and motors given by: Optimal viscosity Optimal viscosity exists for a given component (and system) However, viscosity changes dramatically by temperature!

31 A (fake) Car Talk Puzzle 128 You discovered that on your garage floor that your car is leaking oil. You took it in to the mechanic Joe. Joe was busy, so you had to leave the car at the shop s parking lot for the night. Next morning, Joe took your car into the shop and examined the car for leaks, and found nothing. You took your back home, but lo and behold, the car leaked again on your garage floor. Neither you nor Joe is delusional. What is going on?

Lecture 4. Lab this week: Review: Pilot-Open-Check. Cartridge valves Flow divider Properties of Hydraulic Fluids. Course feedback (2mins)

Lecture 4. Lab this week: Review: Pilot-Open-Check. Cartridge valves Flow divider Properties of Hydraulic Fluids. Course feedback (2mins) 109 Lab this week: Lab 8 Sequencing circuit Lab 9 Flow divider Lecture 4 Review: Pilot-Open-Check Area ratio and pressure divider Cartridge valves Flow divider Properties of Hydraulic Fluids Viscosity

More information

Lecture 6. Systems review exercise To be posted this afternoon Due in class (10/23/15)

Lecture 6. Systems review exercise To be posted this afternoon Due in class (10/23/15) 153 Systems review exercise To be posted this afternoon Due in class (10/23/15) Lecture 6 Coming week: Lab 13: Hydraulic Power Steering Lab 14: Integrated Lab (Hydraulic test bench) Topics today: 2 min

More information

SOFT SWITCHING APPROACH TO REDUCING TRANSITION LOSSES IN AN ON/OFF HYDRAULIC VALVE

SOFT SWITCHING APPROACH TO REDUCING TRANSITION LOSSES IN AN ON/OFF HYDRAULIC VALVE SOFT SWITCHING APPROACH TO REDUCING TRANSITION LOSSES IN AN ON/OFF HYDRAULIC VALVE Michael B. Rannow Center for Compact and Efficient Fluid Power Department of Mechanical Engineering University of Minnesota

More information

Lecture 6. This week: Lab 13: Hydraulic Power Steering [ Lab 14: Integrated Lab (Hydraulic test bench) ]

Lecture 6. This week: Lab 13: Hydraulic Power Steering [ Lab 14: Integrated Lab (Hydraulic test bench) ] 133 Lecture 6 This week: Lab 13: Hydraulic Power Steering [ Lab 14: Integrated Lab (Hydraulic test bench) ] 4-way directional control valve; proportional valve; servo-valve Modeling / Analysis of a servo-valve

More information

Test Which component has the highest Energy Density? A. Accumulator. B. Battery. C. Capacitor. D. Spring.

Test Which component has the highest Energy Density? A. Accumulator. B. Battery. C. Capacitor. D. Spring. Test 1 1. Which statement is True? A. Pneumatic systems are more suitable than hydraulic systems to drive powerful machines. B. Mechanical systems transfer energy for longer distances than hydraulic systems.

More information

TUTORIAL QUESTIONS FOR THE INDUSTRIAL HYDRAULICS COURSE TEP 4205

TUTORIAL QUESTIONS FOR THE INDUSTRIAL HYDRAULICS COURSE TEP 4205 TUTORIAL QUESTIONS FOR THE INDUSTRIAL HYDRAULICS COURSE TEP 4205 The book for the course is Principles of Hydraulic System Design, by Peter J Chapple. Published by Coxmoor Publishing Co., UK. Available

More information

Lecture 25 HYDRAULIC CIRCUIT DESIGN AND ANALYSIS [CONTINUED]

Lecture 25 HYDRAULIC CIRCUIT DESIGN AND ANALYSIS [CONTINUED] Lecture 5 HYDRAULIC CIRCUIT DESIGN AND ANALYSIS [CONTINUED] 1.1 Circuit for Fast Approach and Slow Die Closing A machine intended for high volume production has a high piston velocity. If not controlled,

More information

Lecture 6. Systems review exercise To be posted this weekend Due next Friday (3/6)

Lecture 6. Systems review exercise To be posted this weekend Due next Friday (3/6) 150 Systems review exercise To be posted this weekend Due next Friday (3/6) Lecture 6 Coming week: Lab 13: Hydraulic Power Steering Lab 14: Integrated Lab (Hydraulic test bench) Topics today: Pumps and

More information

Soft Switching Approach to Reducing Transition Losses in an On/Off Hydraulic Valve

Soft Switching Approach to Reducing Transition Losses in an On/Off Hydraulic Valve Soft Switching Approach to Reducing Transition Losses in an On/Off Hydraulic Valve Michael B. Rannow e-mail: rann0018@umn.edu Perry Y. Li 1 e-mail: pli@me.umn.edu Center for Compact and Efficient Fluid

More information

IMECE DEVELOPMENT OF A HIGH-SPEED ON-OFF VALVE FOR SWITCH-MODE CONTROL OF HYDRAULIC CIRCUITS WITH FOUR-QUADRANT CONTROL

IMECE DEVELOPMENT OF A HIGH-SPEED ON-OFF VALVE FOR SWITCH-MODE CONTROL OF HYDRAULIC CIRCUITS WITH FOUR-QUADRANT CONTROL Proceedings of the ASME 010 International Mechanical Engineering Congress & Exposition IMECE010 November 1-18, Vancouver, British Columbia IMECE010-37380 DEVELOPMENT OF A HIGH-SPEED ON-OFF VALVE FOR SWITCH-MODE

More information

ISO 2909 / ASTM D

ISO 2909 / ASTM D Oil Viscosity: Technically, the viscosity of oil is a measure of the oils resistance to shear. Viscosity is more commonly known as resistance to flow. If lubricating oil is considered as a series of fluid

More information

three different ways, so it is important to be aware of how flow is to be specified

three different ways, so it is important to be aware of how flow is to be specified Flow-control valves Flow-control valves include simple s to sophisticated closed-loop electrohydraulic valves that automatically adjust to variations in pressure and temperature. The purpose of flow control

More information

ECH 4224L Unit Operations Lab I Fluid Flow FLUID FLOW. Introduction. General Description

ECH 4224L Unit Operations Lab I Fluid Flow FLUID FLOW. Introduction. General Description FLUID FLOW Introduction Fluid flow is an important part of many processes, including transporting materials from one point to another, mixing of materials, and chemical reactions. In this experiment, you

More information

DISCRETE PISTON PUMP/MOTOR USING A MECHANICAL ROTARY VALVE CONTROL MECHANISM

DISCRETE PISTON PUMP/MOTOR USING A MECHANICAL ROTARY VALVE CONTROL MECHANISM The Eighth Workshop on Digital Fluid Power, May 24-25, 2016, Tampere, Finland DISCRETE PISTON PUMP/MOTOR USING A MECHANICAL ROTARY VALVE CONTROL MECHANISM Michael B. Rannow, Perry Y. Li*, Thomas R. Chase

More information

Nomenclature... xi Hydraulic Laws, Theorems, and Equations...xii

Nomenclature... xi Hydraulic Laws, Theorems, and Equations...xii Nomenclature... xi Hydraulic Laws, Theorems, and Equations...xii 1 Introduction 1.1 Component Design Perspective...1 1.2 Hydraulic Power Evolution...2 1.3 Hydraulic Applications...6 1.4 Component Design

More information

Chapter 7: Thermal Study of Transmission Gearbox

Chapter 7: Thermal Study of Transmission Gearbox Chapter 7: Thermal Study of Transmission Gearbox 7.1 Introduction The main objective of this chapter is to investigate the performance of automobile transmission gearbox under the influence of load, rotational

More information

FPMC EXPERIMENTAL VALIDATION OF A SOFT SWITCH FOR A VIRTUALLY VARIABLE DISPLACEMENT PUMP

FPMC EXPERIMENTAL VALIDATION OF A SOFT SWITCH FOR A VIRTUALLY VARIABLE DISPLACEMENT PUMP Proceedings of the ASME/BATH 2014 Symposium on Fluid Power & Motion Control FPMC2014 September 10-12, Bath, United Kingdom FPMC2014-7857 EXPERIMENTAL VALIDATION OF A SOFT SWITCH FOR A VIRTUALLY VARIABLE

More information

FLUID FLOW. Introduction

FLUID FLOW. Introduction FLUID FLOW Introduction Fluid flow is an important part of many processes, including transporting materials from one point to another, mixing of materials, and chemical reactions. In this experiment, you

More information

DOUBLE, P.O. CHECK VALVES (PRE-ENGINEERED BLOCKS)

DOUBLE, P.O. CHECK VALVES (PRE-ENGINEERED BLOCKS) DOUBLE, P.O. CHECK VALVES (PRE-ENGINEERED BLOCKS) SERIES DOUBLE PILOT OPERATED CHECK VALVE... HS3 Page HD1 Page HD2 SERIES DOUBLE PILOT OPERATED CHECK VALVE GPM PSI LPM BAR CAVITY MODEL PAGE 5 3500 19

More information

Familiarize yourself with the pressure loss phenomenon. The Discussion of this exercise covers the following point:

Familiarize yourself with the pressure loss phenomenon. The Discussion of this exercise covers the following point: Exercise 3-2 Pressure Loss EXERCISE OBJECTIVE Familiarize yourself with the pressure loss phenomenon. DISCUSSION OUTLINE The Discussion of this exercise covers the following point: Pressure loss Major

More information

Fig. 1 Two stage helical gearbox

Fig. 1 Two stage helical gearbox Lecture 17 DESIGN OF GEARBOX Contents 1. Commercial gearboxes 2. Gearbox design. COMMERICAL GEARBOX DESIGN Fig. 1 Two stage helical gearbox Fig. 2. A single stage bevel gearbox Fig. 4 Worm gearbox HELICAL

More information

FEASIBILITY STYDY OF CHAIN DRIVE IN WATER HYDRAULIC ROTARY JOINT

FEASIBILITY STYDY OF CHAIN DRIVE IN WATER HYDRAULIC ROTARY JOINT FEASIBILITY STYDY OF CHAIN DRIVE IN WATER HYDRAULIC ROTARY JOINT Antti MAKELA, Jouni MATTILA, Mikko SIUKO, Matti VILENIUS Institute of Hydraulics and Automation, Tampere University of Technology P.O.Box

More information

Design and Modeling of Fluid Power Systems ME 597/ABE 591

Design and Modeling of Fluid Power Systems ME 597/ABE 591 Systems ME 597/ABE 591 Dr. Monika Ivantysynova MAHA Professor Flud Power Systems MAHA Fluid Power Research Center Purdue University Systems Dr. Monika Ivantysynova, Maha Professor Fluid Power Systems Mivantys@purdue.edu

More information

Power Steering Units - Eaton / Char-Lynn

Power Steering Units - Eaton / Char-Lynn A fully fluid linked steering control unit consisting of a manually operated directional control servo valve and with a feedback meter element in a single body. It is used principally for fluid linked

More information

Heavy Duty Hydrostatic Transmissions

Heavy Duty Hydrostatic Transmissions Heavy Duty Hydrostatic Transmissions Features and Benefits Typical Applications Construction Transit Mixer Road Roller Paver Motor Grader Loader Dozer Material Handling & Utility Crane Sweeper Lift Truck

More information

Glossary. Visit Us Online: ABSOLUTE A measure having as its zero point or base the complete absence of the entity being measured.

Glossary. Visit Us Online:   ABSOLUTE A measure having as its zero point or base the complete absence of the entity being measured. ABSOLUTE A measure having as its zero point or base the complete absence of the entity being measured. ABSOLUTE PRESSURE (psia) The pressure above absolute zero, the sum of atmospheric and gauge pressure.

More information

CRANK-SLIDER SPOOL VALVE FOR SWITCH-MODE CIRCUITS

CRANK-SLIDER SPOOL VALVE FOR SWITCH-MODE CIRCUITS Proceedings of the ASME/BATH 2015 Symposium on Fluid Power & Motion Control FPMC2015 October 12-14, 2015, Chicago, Illinois, United States FPMC2015-9606 CRANK-SLIDER SPOOL VALVE FOR SWITCH-MODE CIRCUITS

More information

Application Note Original Instructions Development of Gas Fuel Control Systems for Dry Low NOx (DLN) Aero-Derivative Gas Turbines

Application Note Original Instructions Development of Gas Fuel Control Systems for Dry Low NOx (DLN) Aero-Derivative Gas Turbines Application Note 83404 Original Instructions Development of Gas Fuel Control Systems for Dry Low NOx (DLN) Aero-Derivative Gas Turbines Woodward reserves the right to update any portion of this publication

More information

Vickers. Proportional Valves. EPV10 Series. Proportional Flow Controls. Released 6/95

Vickers. Proportional Valves. EPV10 Series. Proportional Flow Controls. Released 6/95 Vickers Proportional Valves EPV1 Series Proportional Flow Controls Released 6/95 715 Table of Contents Features and Benefits..............................................................................

More information

Simulation of Pressure Variation in Hydraulic circuit with & without Hydraulic Accumulator in MATLAB-Simhydraulics

Simulation of Pressure Variation in Hydraulic circuit with & without Hydraulic Accumulator in MATLAB-Simhydraulics Simulation of Pressure Variation in Hydraulic circuit with & without Hydraulic Accumulator in MATLAB-Simhydraulics Cherian Johny 1, Dr.K.RSivadas 2 1 PG Student, Department. of Mechanical Engineering,

More information

Fluid Power with Applications

Fluid Power with Applications Fluid Power with Applications Sixth Edition Anthony Esposito Professor Emeritus Department of Manufacturing Engineering Miami University Oxford, Ohio Prentice Hall Upper Saddle River, New Jersey Columbus,

More information

Fluid Power System Model-Based Design. Energy Efficiency. Fluid Power System Model-Based Design Energy Efficiency. K. Craig 1

Fluid Power System Model-Based Design. Energy Efficiency. Fluid Power System Model-Based Design Energy Efficiency. K. Craig 1 Fluid Power System Model-Based Design Energy Efficiency K. Craig 1 Energy in Fluid Power Systems Fluid Power Systems have many advantages: High Power Density Responsiveness and Bandwidth of Operation High

More information

TUTORIAL QUESTIONS FOR COURSE TEP 4195

TUTORIAL QUESTIONS FOR COURSE TEP 4195 TUTORIL QUESTIONS FOR COURSE TEP 4195 Data: Hydraulic Oil Density 870 kg/m 3 bsolute viscosity 0.03 Ns/m 2 Spool valve discharge coefficient 0.62. 1) hydrostatic transmission has a variable displacement

More information

Module 4: Actuators. CDX Diesel Hydraulics. Terms and Definitions. Cylinder Actuators

Module 4: Actuators. CDX Diesel Hydraulics. Terms and Definitions. Cylinder Actuators Terms and Definitions Cylinder Actuators Symbols for Actuators Terms and Definitions II Cylinders Providing Linear Motion Cylinders Providing Angular Motion Parts of Actuators Mounting of Actuators Seals

More information

What does pressure refer to in relation to hydrostatics and what is it dependent on?

What does pressure refer to in relation to hydrostatics and what is it dependent on? Question 1 [3 Marks] What does pressure refer to in relation to hydrostatics and what is it dependent on? Question 2 [14 Marks] Make a circuit diagram of a regular hydraulic plant that is used to control

More information

Hydraulic Proportional and Closed Loop System Design

Hydraulic Proportional and Closed Loop System Design Hydraulic Proportional and Closed Loop System Design Neal Hanson Product Manager Industrial Valves and Electrohydraulics 1 Electrohydraulics Contents 1. Electrohydraulic Principles 2. Proportional Valve

More information

Heat Exchangers (Chapter 5)

Heat Exchangers (Chapter 5) Heat Exchangers (Chapter 5) 2 Learning Outcomes (Chapter 5) Classification of heat exchangers Heat Exchanger Design Methods Overall heat transfer coefficient LMTD method ε-ntu method Heat Exchangers Pressure

More information

FLUID FLOW Introduction General Description

FLUID FLOW Introduction General Description FLUID FLOW Introduction Fluid flow is an important part of many processes, including transporting materials from one point to another, mixing of materials, and chemical reactions. In this experiment, you

More information

FLUID POWER FLUID POWER EQUIPMENT TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS. This work covers part of outcome 2 of the Edexcel standard module:

FLUID POWER FLUID POWER EQUIPMENT TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS. This work covers part of outcome 2 of the Edexcel standard module: FLUID POWER FLUID POWER EQUIPMENT TUTORIAL HYDRAULIC AND PNEUMATIC CYLINDERS This work covers part of outcome 2 of the Edexcel standard module: UNIT 21746P APPLIED PNEUMATICS AND HYDRAULICS The material

More information

Lecture 7. Lab 14: Integrative lab (part 2) Lab 15: Intro. Electro-hydraulic Control Setups (2 sessions)

Lecture 7. Lab 14: Integrative lab (part 2) Lab 15: Intro. Electro-hydraulic Control Setups (2 sessions) Coming week s lab: Lecture 7 Lab 14: Integrative lab (part 2) Lab 15: Intro. Electro-hydraulic Control Setups (2 sessions) 4 th floor Shepherd (room # TBD) Guest lecturer next week (10/30/15): Dr. Denis

More information

Effect of Stator Shape on the Performance of Torque Converter

Effect of Stator Shape on the Performance of Torque Converter 16 th International Conference on AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 16 May 26-28, 2015, E-Mail: asat@mtc.edu.eg Military Technical College, Kobry Elkobbah, Cairo, Egypt Tel : +(202) 24025292

More information

Aircraft Hydraulic Systems Design and Performance

Aircraft Hydraulic Systems Design and Performance Unit T25: Aircraft Hydraulic Systems Design and Performance Unit code: T/504/0126 QCF level: 6 Credit value: 15 Aim The aim of this unit is to give learners an understanding of the principles that underpin

More information

Chapter 1 Gear Design

Chapter 1 Gear Design Chapter 1 Gear Design GTU Paper Analysis Sr. No. Questions Nov 16 May 17 Nov 17 May 18 Theory 1. Explain the following terms used in helical gears: (a) Helix angle; (b) Normal pitch; (c) Axial pitch; (d)

More information

MASSACHUSETTS INSTITUTE OF TECHNOLOGY DEPT OF MECHANICAL ENGINEERING

MASSACHUSETTS INSTITUTE OF TECHNOLOGY DEPT OF MECHANICAL ENGINEERING MASSACHUSETTS INSTITUTE OF TECHNOLOGY DEPT OF MECHANICAL ENGINEERING 2.004 Dynamics and Control II Laboratory Note: Description of the Experimental Rotational Plant 1 INTRODUCTION In the first series of

More information

Modeling and Experimental Testing of the Hondamatic Hydro-Mechanical Power Split Transmission

Modeling and Experimental Testing of the Hondamatic Hydro-Mechanical Power Split Transmission Georgia Institute of Technology Marquette University Milwaukee School of Engineering North Carolina A&T State University Purdue University University of California, Merced University of Illinois, Urbana-Champaign

More information

Lecture 7. Coming week s lab: Integrative lab (your choice!)

Lecture 7. Coming week s lab: Integrative lab (your choice!) Lecture 7 Coming week s lab: Integrative lab (your choice!) Today: Systems review exercise due end of class Your feedback Review: sequencing and asynchronous circuit analysis Hydraulic hybrid vehicles

More information

COMPACT CYLINDER CYLINDER FORCE AND WEIGHT TABLE BASE WEIGHT EFFECTIVE AREA

COMPACT CYLINDER CYLINDER FORCE AND WEIGHT TABLE BASE WEIGHT EFFECTIVE AREA CRS COMPACT CYLINDER STROKE TOLERANCE TEMPERATURE LIMITS VELOCITY LIFE EXPECTANCY SERIES CRS 1 psi min to 15 psi max at zero load [.7 bar min to 1 bar max] air.31 inch [.8 mm] -2 to +18 F [-28 to +82 C]

More information

Module 6 Assignment Part A

Module 6 Assignment Part A Module 6 Assignment Part A TOTAL MARKS Part A = 192 TOTAL QUESTIONS Part A = 36 Question 1 [3 Marks] What does pressure refer to in relation to hydrostatics and what is it dependent on? Question 2 [14

More information

THE LEADING FORCE behind liquids TM since Rotary Positive Displacement Pumps

THE LEADING FORCE behind liquids TM since Rotary Positive Displacement Pumps THE LEADING FORCE behind liquids TM since 1857 Rotary Positive Displacement Pumps External Gear 3600 Series General purpose pumps for transferring, mixing, blending and recirculating. Efficiently handles

More information

Click Here for Printable PDF File. CHAPTER 1 - INTRODUCTION to HYDRAULICS. 1-1 Introduction and Overview. 1-2 Basic Hydraulic Principles

Click Here for Printable PDF File. CHAPTER 1 - INTRODUCTION to HYDRAULICS. 1-1 Introduction and Overview. 1-2 Basic Hydraulic Principles HWH Online Technical School Lesson 1: Introduction to Hydraulics Chapter 1 - INTRODUCTION TO HYDRAULICS (Filename: ML57000-012-CH1.DOC Revised: 22APR16) CHAPTER 1 - INTRODUCTION to HYDRAULICS 1-1 Introduction

More information

TPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 852 / 0815 / E

TPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 852 / 0815 / E HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415

More information

Hydraulic Flywheel Accumulator for Mobile Energy Storage

Hydraulic Flywheel Accumulator for Mobile Energy Storage Hydraulic Flywheel Accumulator for Mobile Energy Storage Paul Cronk University of Minnesota October 14 th, 2015 I. Overview Outline I. Background on Mobile Energy Storage II. Hydraulic Flywheel Accumulator

More information

Determination of power loss of combine harvester travel gear

Determination of power loss of combine harvester travel gear Agronomy Research 13(1), 5 3, 015 Determination of power loss of combine harvester travel gear L. Beneš *, P. Heřmánek and P. Novák Czech University of Life Sciences Prague, Faculty of Engineering, Department

More information

Steering unit LAGZ. Data sheet. Series 2 x

Steering unit LAGZ. Data sheet. Series 2 x Steering unit LAGZ Data sheet Nominal sizes 125 620 Series 2 x Maximum flow 50 l / min HE 11868 / 09.2017 2 LAGZ HE 11868 / 09.2017 Page Content 4 4 5 6 7 8 9 10 11 12 13 14 Features Ordering details Function,

More information

EFFECT OF LUBRICANT SUPPLY PRESSURE ON SFD PERFORMANCE: ENDS SEALED WITH O-RINGS & PISTON RINGS

EFFECT OF LUBRICANT SUPPLY PRESSURE ON SFD PERFORMANCE: ENDS SEALED WITH O-RINGS & PISTON RINGS May 2017 Year V EFFECT OF LUBRICANT SUPPLY PRESSURE ON SFD PERFORMANCE: ENDS SEALED WITH O-RINGS & PISTON RINGS TRC-SFD-01-17 Bonjin Koo Leping Yu Graduate Research Assistants Luis San Andrés Mast-Childs

More information

Lecture 11 HYDRAULIC MOTORS [CONTINUED]

Lecture 11 HYDRAULIC MOTORS [CONTINUED] Lecture 11 HYDRULIC MOORS [CONINUED] 1.12Performance of Hydraulic Motors he performance of hydraulic motors depends upon many factors such as precision of their parts, tolerances between the mating parts,

More information

Cylinders. Standard Features F-1. Frequently Asked Questions, Features

Cylinders. Standard Features F-1. Frequently Asked Questions, Features Frequently Asked Questions, Features Why use Cylinders? Cylinders are the most common and least costly form of hydraulic clamping avail able. They can be sized adequately to allow you to clamp across or

More information

Fluid Flow Conditioning

Fluid Flow Conditioning Fluid Flow Conditioning March 2014 Flow Conditioning There is no flow meter on the market that needs flow conditioning. All flow meters are effective without any type of flow conditioning. 1 Flow Conditioning

More information

Speed-variable revolution in hydraulics

Speed-variable revolution in hydraulics profile Drive & Control Technical Article Speed-variable revolution in hydraulics Challenge: Create hydraulic and electrohydraulic machines that are energy efficient, quiet, inexpensive, fast and precise

More information

Formulas and units

Formulas and units Formulas and units Hydraulic system and circuit design is limited only by the creativity of the application engineer. All basic circuit design begins with the ultimate actuator functions in mind however.

More information

Wind Turbine Emulation Experiment

Wind Turbine Emulation Experiment Wind Turbine Emulation Experiment Aim: Study of static and dynamic characteristics of wind turbine (WT) by emulating the wind turbine behavior by means of a separately-excited DC motor using LabVIEW and

More information

Technical Data. Series Oval Flowmeter. Model 9400

Technical Data. Series Oval Flowmeter. Model 9400 Technical Data Series Oval Flowmeter Model 9400 General The Brodie 9400 Series Oval Flowmeters, Models 9402 through 9459 (sizes 1/2-3 ), are mechanical, positive displacement meters designed for use in

More information

Flow Characteristics of Air in Square Channel Using Perforated Ribs

Flow Characteristics of Air in Square Channel Using Perforated Ribs IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 13, Issue 1 Ver. II (Jan. - Feb. 2016), PP 106-112 www.iosrjournals.org Flow Characteristics of

More information

Revision 9 January 9, 2019

Revision 9 January 9, 2019 Kalsi Seals Handbook Chapter C5 Enhanced Lubrication Kalsi Seals Revision 9 January 9, 2019 Individual chapters of the Kalsi Seals Handbook are periodically updated. To determine if a newer revision of

More information

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.

More information

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES

FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained

More information

Marine Engineering Exam Resource Review of Hydraulics

Marine Engineering Exam Resource Review of Hydraulics 1. What is Pascal s law? Pressure confined on a confined fluid will transmit the pressure in all directions and act with equal force on all areas at right angles. 2. How does the law pertain to hydraulics?

More information

PRESSURE CONTROLS TECNORD

PRESSURE CONTROLS TECNORD Pressure Reducing / Relieving Valves GPM PSI LPM BAR MODEL PAGE 1 4 38 276 DF-PRP 174 2 3 76 27 SK-PRP 176 1 4 38 276 DF-PWP 178 Typical Schematic Typical application for the PRP and PWP is multi-system

More information

Mr.Giridhar Bosch Rexroth (India) Limited A Drive & Control Company. Cylinder Presentation

Mr.Giridhar Bosch Rexroth (India) Limited A Drive & Control Company. Cylinder Presentation Mr.Giridhar Bosch Rexroth (India) Limited A Drive & Control Company Cylinder Presentation Introduction Good Morning Ladies & Gentlemen, We spend the next hour in understanding the Hydraulic Actuator Cylinder.

More information

Steering unit LAGC. Data sheet

Steering unit LAGC. Data sheet Steering unit LAGC Data sheet Nominal sizes Series Maximum flow HE 14365 / 09.2017 40 1000 1 x and 2 x 80 l / min 2 LAGC HE 14365 / 09.2017 Page Content 4 4 5 6 7 8 9 10 11 12 13 14 Features Ordering details

More information

Proportional Valves. Proportional solenoid valves for pressure and flow control

Proportional Valves. Proportional solenoid valves for pressure and flow control Proportional Valves Proportional solenoid valves for pressure and flow control EATON Vickers Screw-In Cartridge Valves V-VLOV-MC-E4 September, 7 - Electro- Proportional Valves Section Contents Typical

More information

IMECE HIGH SPEED ROTARY PULSE WIDTH MODULATED ON/OFF VALVE

IMECE HIGH SPEED ROTARY PULSE WIDTH MODULATED ON/OFF VALVE Proceedings of ASME-IMECE 7 27 ASME International Mechanical Engineering Congress and RD&D Expo November -5, 27, Seattle, Washington USA IMECE27-42559 HIGH SPEED ROTARY PULSE WIDTH MODULATED ON/OFF VALVE

More information

Components of Hydronic Systems

Components of Hydronic Systems Valve and Actuator Manual 977 Hydronic System Basics Section Engineering Bulletin H111 Issue Date 0789 Components of Hydronic Systems The performance of a hydronic system depends upon many factors. Because

More information

Thermal Stress Analysis of Diesel Engine Piston

Thermal Stress Analysis of Diesel Engine Piston International Conference on Challenges and Opportunities in Mechanical Engineering, Industrial Engineering and Management Studies 576 Thermal Stress Analysis of Diesel Engine Piston B.R. Ramesh and Kishan

More information

Pump Control Ball Valve for Energy Savings

Pump Control Ball Valve for Energy Savings VM PCBVES/WP White Paper Pump Control Ball Valve for Energy Savings Table of Contents Introduction............................... Pump Control Valves........................ Headloss..................................

More information

Open Center Compact Valve Custom Installation Guide Rev A

Open Center Compact Valve Custom Installation Guide Rev A 200-0762-01 Open Center Compact Valve Custom Installation Guide 602-0575-01 Rev A 2014-12 Overview This guide provides information for completing a custom AutoSteer valve installation on wheeled farm vehicles

More information

Chapter 11: Flow over bodies. Lift and drag

Chapter 11: Flow over bodies. Lift and drag Chapter 11: Flow over bodies. Lift and drag Objectives Have an intuitive understanding of the various physical phenomena such as drag, friction and pressure drag, drag reduction, and lift. Calculate the

More information

CH.4 Basic Components of Hydraulic and Pneumatic System/16 M HAP/17522/AE5G

CH.4 Basic Components of Hydraulic and Pneumatic System/16 M HAP/17522/AE5G Content : 4.1 Hydraulic and Pneumatic actuators. 10 Marks Hydraulic Actuators - Hydraulic cylinders (single, double acting and telescopic) construction and working, Hydraulic motors (gear and piston type)

More information

Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM

Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM V Prabhu Raja, J Kanchana, K Ramachandra, P Radhakrishnan PSG College of Technology, Coimbatore - 641004 Abstract Loss of machining

More information

Heavy Duty Hydrostatic Transmissions

Heavy Duty Hydrostatic Transmissions Heavy Duty Hydrostatic Transmissions Features and Benefits Typical Applications Construction Transit Mixer Road Roller Paver Motor Grader Loader Dozer Material Handling & Utility Crane Sweeper Lift Truck

More information

Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI.

Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI. Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI. Features Two inch and smaller valves are available with threaded or socket weld ends as

More information

Axial Piston Variable Pump A10VO

Axial Piston Variable Pump A10VO Electric Drives and Controls Hydraulics inear Motion and Assembly Technologies Pneumatics ervice Axial Piston Variable Pump A10VO RA 92703/11.07 1/44 Replaces: 06.07 Data sheet eries 52/53 ize 10...85

More information

Single-phase Coolant Flow and Heat Transfer

Single-phase Coolant Flow and Heat Transfer 22.06 ENGINEERING OF NUCLEAR SYSTEMS - Fall 2010 Problem Set 5 Single-phase Coolant Flow and Heat Transfer 1) Hydraulic Analysis of the Emergency Core Spray System in a BWR The emergency spray system of

More information

Logic elements. Differential pressure sensing elements for applications up to 350 bar (5000 psi) and 400 L/min (100 USgpm)

Logic elements. Differential pressure sensing elements for applications up to 350 bar (5000 psi) and 400 L/min (100 USgpm) Hydraulic Screw-in Cartridge Valves (SiCV) Logic elements Differential pressure sensing elements for applications up to 50 bar (5000 psi) and 400 L/min (00 USgpm) Logic elements LOGC ELEMENTS... -4 APPLCATON

More information

KTM V-PORT CONTROL BALL VALVE FULL BORE AND REDUCED BORE

KTM V-PORT CONTROL BALL VALVE FULL BORE AND REDUCED BORE A rugged, long-life V-port control ball valve with excellent flow characteristics for various fluids including slurries and fibers FEATURES GENERAL APPLICATION Steam, liquids, gas or critical services

More information

TESIGNG OF FUELS: VISCOSITY OF LIQUID FUELS

TESIGNG OF FUELS: VISCOSITY OF LIQUID FUELS Department of Mechanical Engineering Indian Institute of Technology New Delhi II Semester -- 2017 2018 MCL 241 Energy systems and Technologies TESIGNG OF FUELS: VISCOSITY OF LIQUID FUELS 1. Introduction

More information

Hydraulic drives market trends and offerings

Hydraulic drives market trends and offerings White Paper Hydraulic drives market trends and offerings S.Krishnakumar Industrial Drives - Hydraulics Eaton India Engineering Center Pune, India Keywords: Hydraulic Drives; Motors; Radial Piston Motor;

More information

FPMC A NEW HYDRAULIC PUMP AND MOTOR TEST BENCH FOR EXTREMELY LOW OPERATING SPEEDS

FPMC A NEW HYDRAULIC PUMP AND MOTOR TEST BENCH FOR EXTREMELY LOW OPERATING SPEEDS Proceedings of the 2017 Bath/ASME Symposium on Fluid Power and Motion Control FPMC2017 October 16-19, 2017, Sarasota,FL, USA A NEW HYDRAULIC PUMP AND MOTOR TEST BENCH FOR EXTREMELY LOW OPERATING SPEEDS

More information

DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK. Sub. Code/Name: ME1305 Applied Hydraulics and Pneumatics Year/Sem: III/V

DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK. Sub. Code/Name: ME1305 Applied Hydraulics and Pneumatics Year/Sem: III/V DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Sub. Code/Name: ME1305 Applied Hydraulics and Pneumatics Year/Sem: III/V UNIT-1 FLUID POWER SYSTEMS AND FUNDAMENTALS 1. Define fluid power? 2. List the

More information

Exercise 4-1. Flowmeters EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION. Rotameters. How do rotameter tubes work?

Exercise 4-1. Flowmeters EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION. Rotameters. How do rotameter tubes work? Exercise 4-1 Flowmeters EXERCISE OBJECTIVE Learn the basics of differential pressure flowmeters via the use of a Venturi tube and learn how to safely connect (and disconnect) a differential pressure flowmeter

More information

12AT/50AT Series. Spin-On Filters. Global Filtration Technology

12AT/50AT Series. Spin-On Filters. Global Filtration Technology 1AT/5AT Series Spin-On Filters Global Filtration Technology 1 1AT/5AT Series Applications for Spin-On Filters n Mobile Equipment n Hydrostatic Drives n Industrial Power Units n Reservoir Breathers Often,

More information

IMECE HIGH SPEED ROTARY PULSE WIDTH MODULATED ON/OFF VALVE

IMECE HIGH SPEED ROTARY PULSE WIDTH MODULATED ON/OFF VALVE Proceedings of ASME-IMECE 7 27 ASME International Mechanical Engineering Congress and RD&D Expo November -5, 27, Seattle, Washington USA IMECE27-42559 HIGH SPEED ROTARY PULSE WIDTH MODULATED ON/OFF VALVE

More information

Universal APU2 Pump Automotive Paint Series

Universal APU2 Pump Automotive Paint Series Universal APU2 Pump Automotive Paint Series New levels of performance. Reduced paint shop and mix room costs. For more than half a century, Waukesha Cherry-Burrell has been a leader in the design, manufacturing

More information

RESEARCH OF THE DYNAMIC PRESSURE VARIATION IN HYDRAULIC SYSTEM WITH TWO PARALLEL CONNECTED DIGITAL CONTROL VALVES

RESEARCH OF THE DYNAMIC PRESSURE VARIATION IN HYDRAULIC SYSTEM WITH TWO PARALLEL CONNECTED DIGITAL CONTROL VALVES RESEARCH OF THE DYNAMIC PRESSURE VARIATION IN HYDRAULIC SYSTEM WITH TWO PARALLEL CONNECTED DIGITAL CONTROL VALVES ABSTRACT The researches of the hydraulic system which consist of two straight pipelines

More information

whitedriveproducts SERIES Hydraulic Motor LIGHT DUTY

whitedriveproducts SERIES Hydraulic Motor LIGHT DUTY whitedriveproducts SERIES 145-146 - LIGHT DUTY Hydraulic Motor www.cenhyd.com 1(800)264-9571 WD WD (All Series) whitedriveproducts overview The WD motor series is an economical solution for light duty

More information

The Discussion of this exercise covers the following points:

The Discussion of this exercise covers the following points: Exercise 3-3 Venturi Tubes EXERCISE OBJECTIVE In this exercise, you will study the relationship between the flow rate and the pressure drop produced by a venturi tube. You will describe the behavior of

More information

R10 Set No: 1 ''' ' '' '' '' Code No: R31033

R10 Set No: 1 ''' ' '' '' '' Code No: R31033 R10 Set No: 1 III B.Tech. I Semester Regular and Supplementary Examinations, December - 2013 DYNAMICS OF MACHINERY (Common to Mechanical Engineering and Automobile Engineering) Time: 3 Hours Max Marks:

More information

GPM Hydraulic Flow Meter User Manual

GPM Hydraulic Flow Meter User Manual 4278 100 GPM Hydraulic Flow Meter User Manual Introduction The OTC 4278 Hydraulic Flow Meter has been designed for easy connection to a hydraulic circuit so that flow, pressure and temperature can be readily

More information

Bearings. Rolling-contact Bearings

Bearings. Rolling-contact Bearings Bearings A bearing is a mechanical element that limits relative motion to only the desired motion and at the same time it reduces the frictional resistance to the desired motion. Depending on the design

More information

Applied Fluid Mechanics

Applied Fluid Mechanics Applied Fluid Mechanics 1. The Nature of Fluid and the Study of Fluid Mechanics 2. Viscosity of Fluid 3. Pressure Measurement 4. Forces Due to Static Fluid 5. Buoyancy and Stability 6. Flow of Fluid and

More information