This is a guide to tearing down and rebuilding a Fox Racing Shox DHX 3/4/5 Coil shock. It shows the user how to:

Size: px
Start display at page:

Download "This is a guide to tearing down and rebuilding a Fox Racing Shox DHX 3/4/5 Coil shock. It shows the user how to:"

Transcription

1 Fox DHX Coil Rebuild Introduction: This is a guide to tearing down and rebuilding a Fox Racing Shox DHX 3/4/5 Coil shock. It shows the user how to: Dismantle the shock Clean internal parts Replace internal o rings Replace main shaft seal o ring Replace oil Reassembly of the shock unit Note: The Propedal and rebound assembly s are not dismantled or altered. If you have a dead rebound/propedal assembly, this guide will not help. To successfully dismantle the rebound and/or propedal assembly s, shaft clamps are required; the process also involves the use of a propane torch to heat the Loctited components. If not done correctly, damage will result to the shock (and your wallet) Disclaimer: This guide is not endorsed by Fox Racing Shox! By proceeding with this guide, the instant you open your shock, you voluntarily and knowingly forfeit any warranty that came with the shock. Do not proceed with these procedures if you are not mechanically inclined! If you have a tendency to round/strip every screw you touch, put the tools down NOW! Any damage you cause to your shock due to your own mistakes is YOUR FAULT. Do not expect any sympathy from me, or any sympathy from Fox (or warranty). YOU have to pay to have the unit fixed. This guide was devised with care, with information gained from a number of sources. This procedure works if carried out CAREFULLY and with PATIENCE. I AM NOT RESPONSIBLE FOR ANY DAMAGE YOU CAUSE TO YOUR SHOCK, BIKE, PERSONA OR SURROUNDS, USE COMMON SENSE AND TAKE THE FIRST FEW RIDES EASY, TO ENSURE YOU HAVE CORRECTLY REPAIRED THE SHOCK. WARNING! READ ALL Instructions twice before you commence with the rebuild, and ensure you understand its procedures

2 Preliminaries Tool list: Spanners Wooden vice Soft jaw vice Long nose pliers O ring / Dental picks (for removal of o rings) Clean rags Clean work bench Oil drip Pan Safety glasses Parts list: Replacement o rings, the best way to get these is to take the removed o rings to a local 0 ring supplier and get them sized up properly for replacement ones, I also recommend you buy a good amount of each, it s always good to have spares for next time, label them and put them in a compartment container Fork/shock oil. Ensure you use a high quality, fully synthetic oil. I use 10W Castrol Fully synthetic fork fluid. The DHX comes stock with 10W Fox Fluid (rebadged Torco RSF medium) If you wish to use a different weight oil, this website has a lot of useful info on shock oil; Further Information: Here is a list of websites that have lots of useful information on rear shocks, for anyone who is interested in learning more about their rear shocks. Information on EVERYTHING regarding suspension, explaining different types of damper systems, set up info on a range of shocks etc; these site s are well worth reading through! : Some useful info on how to mod shim stacks, for those who are interested in modifying their shim stacks, (undertake this at your own risk!) Website with lots of info regarding things like oil weights etc: Righto, if you feel confident, and have read this guide at least twice (yes that was an instruction!), clean your work area, gather your tools, and lets begin!

3 STEP 1: Removing shock 1. Firstly, you will need to remove the shock from your bike; it will be different on every bike, so if you don t know how to remove your shock, STOP NOW! 2. After you have removed the shock from the bike, place on your work bench, and give it a good wipe over with a clean cloth, to remove dust and dirt 3. Next remove the spring, and in my case, the shock boot 4. Back off all adjustments (Least Propedal, Bottom Out and Rebound) 5. DEFLATE THE BOOST VALVE! 6. Give the shock body a good clean, you don t need any dirt or debris s getting inside the shock 7. Clamp the shock body in a wooden vice

4 STEP 2: Removing Bottom Out Adjuster 8. Loosen the two grub screws on the bottom out adjuster with a hex key 9. Remove the adjuster, and set it aside 10. Using either a spanner or wrench, loosen the grey cap 11. After the threads have been disengaged, pull the assembly out, and set it aside 12. You can now see the IFP (Internal Floating Piston) and the bleed screw in the middle 13. Use a measuring device and measure the depth of the IFP, The depth will be different for different stroke lengths and eye to eye measurements 14. Alternatively, use the IFP depth Chart at the end of this document

5 STEP 3: Removing the IFP 15. Depress the shaft all the way down 16. Remove the bleed screw from the centre of the IFP with a hex key 17. Pull the bleed screw out, and set it aside in a safe place 18. Using long needle nosed pliers, pull the IFP out of the Piggyback Chamber 19. Remove the IFP 20. Place the IFP aside, and pull the shaft out to full extension

6 STEP 4: Removing the Shaft assembly 21. Wrap an old tube around the shaft, this will prevent damage to the shaft should you slip with the spanner 22. Using a spanner or wrench, undo the shaft cap, it may be tight, keep applying even pressure and it will undo 23. After its loosened, use your hand to unthread the shaft 24. Pull the shaft and piston assembly out of the shock body 25. Set the shaft assembly aside 26. Drain the oil from the Piggyback and main chamber into an oil pan, wipe the body with a clean cloth and set the body aside

7 STEP 5: Removing Piston and Seal Housing Assembly 27. Clamp the shaft eyelet reducers in a soft jaw vice, or use blocks of wood as shown in the first picture, this will prevent damage to the reducers 28. Use a small spanner and undo the black piston bolt 29. Remove the piston and shim assembly, be careful not to muck up the shim stack 30. Lift off the black seal housing, being careful not to knock the rebound needle in the centre of the shaft 31. Place the seal housing on your work bench, be careful not to scratch the orange bushing 32. You can now access the yellow dust seal and black main shaft o ring between the yellow dust wiper and orange bushing 33. If you shock has had sufficient use there will probably be dirt and crud in the yellow dust seal, wipe it clean

8 STEP 6: Removing Shaft O-ring, IFP O-ring and Housing O-Ring 34. Using a pin or dental pick, stab the black o ring and pry it out, being careful not to scratch the yellow dust seal or orange bushing 35. Label the o ring so you know which one it is and set it aside for now 36. Using your pick, remove the housing o ring 37. Label the housing o ring, and put it aside 38. Using your pick, remove the IFP o ring 39. Label the IFP o ring and set it aside

9 STEP 7: Removing Bottom Out assembly o- rings and cleaning shock internals 40. Using your pick, remove the bottom out plunger o ring, label and set aside the o ring 41. Using your pick, remove the Bottom out housing o ring, label and set aside the o ring 42. The Bottom out assembly with its o rings 43. Using a clean cloth, wipe out the main shaft chamber 44. Using a clean cloth, wipe out the piggyback chamber 45. You have now disassembled you shock. Take the o rings to a local supplier and have them sized up and replaced, I recommend getting a quantity of each, labelling them and putting them in a container for next time, it s always good to have a supply of them

10 STEP 8: Replacing main shaft o-ring and shaft housing o-ring 46. Take your new main shaft o ring, apply a few drops of suspension oil to it and pinch as shown 47. Insert the pinched o ring into shaft housing as shown 48. Place your pinkie in opposite end as shown 49. Using you other pinkie, squash the o ring into the housing and use your fingers to set the o ring in its housing, this can be tricky, take your time and it will go in 50. Take you new shaft housing seal, and place a few drops of suspension oil onto it 51. Insert it back onto housing

11 STEP 9: Replacing IFP and Bottom Out assembly o-rings, reassembling shaft assembly 52. Place a few drops of suspension fluid on a new IFP o ring, and place it back on the IFP (In picture, new o ring is in place on IFP, old one is next to IFP) 53. Place a few drops of suspension fluid on new bottom out housing and adjuster o rings, then place them back on the assembly (the position of the old o rings on the table is respective of where they go on the BO assembly) 54. Wipe some suspension fluid on shaft, and replace rubber bottom out bumper 55. Reinsert the shaft seal housing back onto the shaft, be careful to put it on straight, take your time, DO NOT FORCE IT, otherwise damage to the shaft or bushing may result 56. Replace the piston/shim assembly, and retighten. Just snug it tight, if you over tighten it too much, you may crush the shims and prevent them flexing 57. After you have retightened the piston, pull the shaft housing all the way up. You have now successfully rebuilt the shaft assembly

12 STEP 9: Refilling oil and reinstalling shaft assembly 58. Refill the main chamber with oil 59. Let it filter into piggyback chamber and keep filling until piggyback chamber is almost overflowing 60. Place the IFP into the chamber, press it so it just sits on the top of the threads (ensure bleed screw is in) 61. Fill main chamber with suspension oil until it is almost overflowing 62. While holding IFP in place, reinsert the piston into the chamber and thread the seal housing on, hand tighten it at this stage. It s good to place a drip pan underneath the shock, as oil will overflow 63. Remove IFP bleed screw

13 STEP 10: Reinserting IFP and reinstalling Bottom Out assembly 64. Depress IFP past threads, ensure bleed screw is removed, and wear safety glasses, as oil will squirt through bleed hole 65. Using you measuring tool, push IFP to its correct depth. If you did not record your IFP depth, use the depth chart at the end of this document. Tap body to displace any trapped air as your pushing the IFP in, this will ensure a good bleed 66. Reinstall bleed screw, drain and wipe excess oil from IFP chamber 67. Using spanner or wrenches, retighten the shaft housing. Its recommended that you use the old tube to protect the shaft 68. Reinsert the bottom out assembly 69. Using a spanner or wrench, tighten the grey cap

14 STEP 12: Final Reassembly 70. Reinstall the Bottom Out adjuster cap 71. Tighten the 2 grub screws 72. Reinflate the boost valve to a minimum of 125PSI 73. Clean the shock over with Isopropyl Alcohol or a wet cloth 74. Reinstall spring, any reducers and valve cap (and in my case, my shock boot) 75. Reinstall the shock back onto your bike 76. Do the bounce test on your bike to lube internal parts, then set adjustments to your settings, bounce check again to make sure everything is working correctly 77. Success = BEER!

15 IFP Depth Chart: EYE to EYE Stroke Metric; 190mm, 50mm = 32mm 200mm, 50mm = 32mm 200mm, 57mm = 33mm 215mm, 64mm = 34mm 222mm, 64mm = 34mm 241mm, 76mm = 38mm Imperial; 7.500, 2.00 = , 2.00 = , 2.25 = , 2.50 = , 2.50 = , 3.00 = 1.48 Thanks to EmanResu on MTBR for finding the IFP chart Be sure to check out his awesome guide on bleeding a DHX Air!

16 Acknowledgements Big thanks to the people who contributed their valuable knowledge to help me compile this guide, id name you individually, but you know who you are! Info obtained from people on: MTBR Pinkbike ROTORBURN AUSTRALIA (formally FARKIN) Ride Monkey This guide was compiled by me, Nick_M2R, on 18 th May 2009, repost this guide if you wish. While I have proof read this guide carefully, I m only human, and its late at night. If you notice any mistakes or have any improvements, PM me on MTBR and ill include them in future releases. Enjoy Guys and Girls! Version: 1

FOX Racing Shox Bypass Technical Manual.

FOX Racing Shox Bypass Technical Manual. FOX Racing Shox Bypass Technical Manual. The following technical manual will be using a 2.5 dia. shock with three tubes for descriptions and illustrations. Your shock may differ in the number of tubes,

More information

Shock Absorber Rebuild Manual

Shock Absorber Rebuild Manual Shock Absorber Rebuild Manual Model PODIUM RC3 FOX RACING SHOX 130 Hangar Way, Watsonville, CA 95076 PHONE 800.369.7469 FAX 831.768.7026 Email: psservicemw@ridefox.com Website: www.ridefox.com Disclaimer

More information

2006 SID SERVICE GUIDE

2006 SID SERVICE GUIDE 2006 SID SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Information contained in this publication is subject

More information

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Information contained in this publication is subject to change at anytime

More information

Shock Absorber Rebuild Manual

Shock Absorber Rebuild Manual Shock Absorber Rebuild Manual Model PODIUM X FOX RACING SHOX 130 Hangar Way, Watsonville, CA 95076 PHONE 800.369.7469 ext. 7647 FAX 831.768.7026 Email: info@foxracingshox.com Website: www.foxracingshox.com

More information

Maverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.2 SHOCK SERVICE MANUAL

Maverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.2 SHOCK SERVICE MANUAL Maverick American 3085 Bluff Street Boulder, CO 80301 Tel: 303-415-0370 Fax: 303-415-0676 www.maverickamerican.com ML7.2 SHOCK SERVICE MANUAL 1. OVERVIEW 1.1. The Maverick ML7.2 rear shock is an oil damped

More information

Maverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.0 SHOCK SERVICE MANUAL

Maverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.0 SHOCK SERVICE MANUAL Maverick American 3085 Bluff Street Boulder, CO 80301 Tel: 303-415-0370 Fax: 303-415-0676 www.maverickamerican.com ML7.0 SHOCK SERVICE MANUAL 1. OVERVIEW 1.1. The Maverick ML7.0 rear shock is an oil damped

More information

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Contact your local distributor or visit the RockShox website at www.rockshox.com

More information

TOPAZ Service Guide. Full Service

TOPAZ Service Guide. Full Service TOPAZ Service Guide Full Service SERVICE OVERVIEW This manual will guide you step by step performing an air service to your Topaz. Please follow each instruction carefully to achieve the best and safest

More information

2006 RECON SERVICE GUIDE

2006 RECON SERVICE GUIDE 2006 RECON SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Information contained in this publication is subject

More information

SID REAR SERVICE GUIDE

SID REAR SERVICE GUIDE 2003-2004 SID REAR SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Contact your local distributor or visit

More information

Air Sleeve Maintenance

Air Sleeve Maintenance Air Sleeve Maintenance and Stuck-Down Troubleshooting Tools required: Safety glasses, gloves, strap wrench, shop towel, 1/4 -diameter 6 breaker bar, FOX High Pressure Pump, dental pick, hex wrench(es)

More information

2013 Monarch RL Service Manual

2013 Monarch RL Service Manual 2013 Monarch RL Service Manual GEN.0000000004177 Rev A Copyright 2012 SRAM, LLC SRAM LLC WARRANTY Extent of Limited Warranty Except as otherwise set forth herein, SRAM warrants its products to be free

More information

1. Get fork mounted in stand. You can leave it in the bike, but you must remove the wheel and front brake.

1. Get fork mounted in stand. You can leave it in the bike, but you must remove the wheel and front brake. Tools Needed: Bike stand Lint free shop Towels 1.5mm Allen Key Pick Set Grease (We recommend Slick Honey) Oil Measuring Cup (with cc Scale) Small Metal Drift Shop Vise Oil Bucket 13mm Deep Socket (6 point)

More information

Rear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)

Rear End Installation and Bearing Kit - 8.8in (86-12 V8; V6) Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black

More information

2013 Monarch RT3 Relay Service Manual

2013 Monarch RT3 Relay Service Manual 2013 Monarch RT3 Relay Service Manual GEN.0000000004235 Rev A 2013 SRAM LLC SRAM LLC WARRANTY Extent of Limited Warranty Except as otherwise set forth herein, SRAM warrants its products to be free from

More information

Lowering Spring Installation on a Mustang GT

Lowering Spring Installation on a Mustang GT Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a

More information

Creation Date Last Mod Date Model Year Drawings Estimated Time. 5/22/2009 6/15/2009 S120/S90/E min.

Creation Date Last Mod Date Model Year Drawings Estimated Time. 5/22/2009 6/15/2009 S120/S90/E min. You are here: Service > Forks > 2008 > E100 > S120/S90/E100 50-hour Service Open the Specialized Business Online site in a new window... S120/S90/E100 50-hour Service Creation Date Last Mod Date Model

More information

(english) technical manual. part#

(english) technical manual. part# 008 (english) technical manual part# 95-4015-016-000 SRAM original Parts Caution: The SRAM Warranty policy does not cover damages caused by the use of non-sram parts. Use only SRAM parts with SRAM components.

More information

FORK FREE PISTON MODIFICATION 2011 HONDA CRF250R

FORK FREE PISTON MODIFICATION 2011 HONDA CRF250R 217 Lorain Place Los Gatos, California 95032 408.406.2089 www.smartperformanceinc.com www.spi-racing.com FORK FREE PISTON MODIFICATION 2011 HONDA CRF250R WHAT? All production versions of the 2011 HONDA

More information

Double Barrel Service Instructions Cane Creek R&D. January 2009 V2.0 1

Double Barrel Service Instructions Cane Creek R&D. January 2009 V2.0 1 Double Barrel Service Instructions Cane Creek R&D January 2009 V2.0 1 Table of Contents 3. Diagnosis for Parts Needed 4. Work Flow 5. Initial Disassembly 6. Initial Disassembly Pictures 8. Reservoir Rebuild

More information

ACURA NSX ABS/ALB Modulator Rebuild Procedure

ACURA NSX ABS/ALB Modulator Rebuild Procedure Version 03 ACURA NSX ABS/ALB Modulator Rebuild Procedure I rebuilt my 1991 ABS/ALB modulator using this procedure. Please note that this will not guarantee that your ABS/ALB system issues will be resolved

More information

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS 82-L0352 REV 8 4-27-2011 WARNING! HYDRAULIC COMPONENTS CAN CAUSE SERIOUS INJURY OR DEATH IF PROPER SAFETY PRECAUTIONS ARE

More information

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web: Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748 Garching

More information

Sachs 48mm Closed Cartridge fork Service Manual

Sachs 48mm Closed Cartridge fork Service Manual Sachs 48mm Closed Cartridge fork Service Manual 1 Fork seal driver 2 Special soft jaws 3 Fork cap wrench 4 Rebound rod holding tool 5 Compression assembly holding tool 6 Retaining clip tool Special Tools

More information

Lefty MAX 140 Travel Management, service. Lefty MAX 140 Travel management, service

Lefty MAX 140 Travel Management, service. Lefty MAX 140 Travel management, service Lefty MAX 140 Travel management, service THE FOLLOWING SERVICE SHOULD BE PERFORMED AFTER EVERY 40-80 HOURS OF RIDING, OR AT LEAST ONCE A YEAR. THE INSTRUCTIONS ARE FOR ADVANCED MECHANICS. THEY DO NOT REPLACE

More information

2017 Reverb Stealth. Service Manual. GEN Rev B 2016 SRAM, LLC

2017 Reverb Stealth. Service Manual. GEN Rev B 2016 SRAM, LLC 2017 Reverb Stealth Service Manual GEN.0000000005101 Rev B 2016 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects

More information

2014-Present Vivid Service Manual

2014-Present Vivid Service Manual 2014-Present Vivid Service Manual SRAM LLC WARRANTY Extent of Limited WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects in materials or workmanship for a

More information

FORK GOLD VALVE INSTALLATION STREET / ROAD RACE 37mm BPF SFF

FORK GOLD VALVE INSTALLATION STREET / ROAD RACE 37mm BPF SFF 1501 Pomona Rd, Corona, CA 92880 951.279.6655 racetech.com FORK GOLD VALVE INSTALLATION STREET / ROAD RACE 37mm BPF SFF FK code FMGV S3702C P Thede 2.27.15 5 pgs TOOLS REQUIRED:

More information

Reverb Stealth A2 & B1

Reverb Stealth A2 & B1 Reverb Stealth A2 & B1 service manual GEN.0000000005341 Rev B 2017 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from

More information

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web: Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748 Garching

More information

DebonAir Upgrade and Travel Change Kit

DebonAir Upgrade and Travel Change Kit DebonAir Upgrade and Travel Change Kit 35 mm Forks Lyrik B1 (2016+) PIKE A1-A2 (2014-2017) PIKE B1 (2018+) Revelation A1 (2018+) Yari A1 (2016+) BoXXer C1 (2019+) service manual GEN.0000000005734 Rev A

More information

2015-Present BoXXer World Cup

2015-Present BoXXer World Cup 2015-Present BoXXer World Cup Service Manual GEN.0000000004665 Rev D 2016 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free

More information

PRESENT. VIVID AIR SERVICE MANUAL Service Manual

PRESENT. VIVID AIR SERVICE MANUAL Service Manual 2014 - PRESENT VIVID AIR SERVICE MANUAL Service Manual SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects in materials

More information

Owners manual. Öhlins Superbike front fork FG 170

Owners manual. Öhlins Superbike front fork FG 170 Owners manual Öhlins Superbike front fork FG 0 Including: Setting up your fork Changing springs and seals Service the fork Trouble shooting Technical info Spare parts & tools Öhlins super bike front fork

More information

DUAL AIR SERVICE GUIDE

DUAL AIR SERVICE GUIDE 1999-2004 DUAL AIR SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Contact your local distributor or visit

More information

3. Park vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction.

3. Park vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. InstalL Instructions ram assist single-ended ram rebuild kit 304201-kit 304202-kit (for 1.5" bore x 3/4" rod rams with 6" or 8" stroke) (for 2" bore x 3/4" rod rams with 6" or 8" stroke) kit contents 304202-ins

More information

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952)

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952) Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION

More information

Shock Absorber for Formula Student and Formula SAE TTX 25. Workshop Manual

Shock Absorber for Formula Student and Formula SAE TTX 25. Workshop Manual Shock Absorber for Formula Student and Formula SAE TTX 5 Workshop Manual SAFETY PRECAUTIONS General Warnings Note! The shock absorber is an important part of the vehicle and will affect the stability.

More information

TCI Trans-Scat

TCI Trans-Scat Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive

More information

PILOT SL & XC SERVICE GUIDE

PILOT SL & XC SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. 2003-2004 PILOT SL & XC SERVICE GUIDE Contact your local distributor or

More information

1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4" fittings

1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4 fittings 1986 Rear Disk Brake Upgrade Being well prepared for a project of this size is the key to success. I thought I was well prepared by doing a lot of research and getting all of the required parts before

More information

2014-Present Pike Instructions apply to 15x100 and Boost 110 forks. Specific part information can be found in the Spare Parts Catalog.

2014-Present Pike Instructions apply to 15x100 and Boost 110 forks. Specific part information can be found in the Spare Parts Catalog. 2014-Present Pike Instructions apply to 15x100 and Boost 110 forks. Specific part information can be found in the Spare Parts Catalog. Service Manual GEN.0000000004461 Rev D 2015 SRAM, LLC SRAM LLC WARRANTY

More information

INSTALLATION GUIDE. RMS510, 511, 512, 513, 511MC 510-OR, 512-OR Manual Revision:

INSTALLATION GUIDE. RMS510, 511, 512, 513, 511MC 510-OR, 512-OR Manual Revision: REKLUSE MOTOR SPORTS z-start Dual-Actuated Brake Kit INSTALLATION GUIDE RMS510, 511, 512, 513, 511MC 510-OR, 512-OR 196-210 Manual Revision: 051309 2002-2009 Rekluse Motor Sports Rekluse Motor Sports,

More information

PIKE DUAL AIR PICTORIAL INSTRUCTIONS. INSTRUCTIONS FOR INSTALLING ENDURO FORK SEALS AND CHANGING SEMI-BATH OIL in RockShox PIKE Dual Air Forks

PIKE DUAL AIR PICTORIAL INSTRUCTIONS. INSTRUCTIONS FOR INSTALLING ENDURO FORK SEALS AND CHANGING SEMI-BATH OIL in RockShox PIKE Dual Air Forks INSTRUCTIONS FOR INSTALLING ENDURO FORK SEALS AND CHANGING SEMI-BATH OIL in RockShox PIKE Dual Air Forks RECOMMENDED PARTS AND TOOLS -Bicycle work stand -Plastic bucket/drain pan -5mm Allen wrench -DH

More information

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web: Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748 Garching

More information

FORK COMPRESSION AND REBOUND GOLD VALVE INSTALLATION - DIRT 35C/30R SFF

FORK COMPRESSION AND REBOUND GOLD VALVE INSTALLATION - DIRT 35C/30R SFF 1501 Pomona Rd, Corona, CA 92880 951.279.6655 racetech.com FORK COMPRESSION AND REBOUND GOLD VALVE INSTALLATION - DIRT 35C/30R SFF FK code 2 part LS FMGV 3521C P Thede 12.3.15 7 pgs

More information

SHOCK GOLD VALVE INSTALLATION STREET/RR 46mm LD (40/36)

SHOCK GOLD VALVE INSTALLATION STREET/RR 46mm LD (40/36) SK code SHOCK GOLD VALVE INSTALLATION STREET/RR 46mm LD (40/36) P Thede 4.22.10 5 pgs TOOLS REQUIRED: Metric Micrometer, Calipers or a Metric Ruler, Torque Wrench, High Pressure

More information

Mega Air Pull-Shock Service Manual

Mega Air Pull-Shock Service Manual Mega Air Pull-Shock Service Manual K2 BIKE / NOLEEN RACING 19215 VASHON HWY. SW VASHON, WA 98070 206-463-8800 WWW.K2BIKE.COM SHOCK DISAS- SEMBLY AND ASSEMBLY In this section: Tools needed Shock Design

More information

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13.

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13. Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961

More information

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,

More information

SUSPENSION FORK OIL, AIR, AND COIL CHARTS

SUSPENSION FORK OIL, AIR, AND COIL CHARTS 2014 SUSPENSION FORK OIL, AIR, AND COIL CHARTS GEN.0000000004392 Rev A 2013 SRAM LLC RockShox Oil Volume Chart Drive Side Non-Drive Side Fork Model Damper Technology Upper Tube Volume (ml) Oil wt Lower

More information

2005 RADIUM/ METEL SHOCK SERVICE MANUAL

2005 RADIUM/ METEL SHOCK SERVICE MANUAL 2005 RADIUM/ METEL SHOCK SERVICE MANUAL PN 042132,. '05 RADIUM/ METEL SHOCK SERVICE MANUAL Page 1 PN 042132 2005 RADIUM/ METEL SHOCK SERVICE MANUAL INDEX Section Description Page 1 INTRODUCTION 3 2 SETUP,

More information

Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer

Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift

More information

RS-1. Service Manual

RS-1. Service Manual 2015 RS-1 Service Manual SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects in materials or workmanship for a period of

More information

BoXXer Team

BoXXer Team 2015-2018 BoXXer Team Service Manual GEN.0000000005721 Rev A 2018 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from

More information

Reverb A2 & B1. service manual. GEN Rev A 2017 SRAM, LLC

Reverb A2 & B1. service manual. GEN Rev A 2017 SRAM, LLC Reverb A2 & B1 service manual GEN.0000000005342 Rev A 2017 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects

More information

Model year 2014 USER MANUAL

Model year 2014 USER MANUAL Model year 2014 USER MANUAL WARRANTY Terms and conditions BOS MTB offers warranty on its products on the following terms: BOS MTB guarantees to the original purchaser that the BOS product for which they

More information

Difficulty Grading expert Wrench Time 1 hour Tip, Strip or Tune Strip Spares Needed Oil Seals 4.99 (pr), Dust Seals 5.75 (pr)

Difficulty Grading expert Wrench Time 1 hour Tip, Strip or Tune Strip Spares Needed Oil Seals 4.99 (pr), Dust Seals 5.75 (pr) URFNVKR[VHUYLFH Difficulty Grading expert Wrench Time 1 hour Tip, Strip or Tune Strip Spares Needed Oil Seals 4.99 (pr), Dust Seals 5.75 (pr) 22mm socket Rubber mallet Allen keys Small Phillips screwdriver

More information

2018 Super Deluxe Coil

2018 Super Deluxe Coil 2018 Super Deluxe Coil service manual GEN.0000000005361 Rev A 2017 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from

More information

BMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com

BMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com BMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com BMW E46 Line #23 Replacment Guide, page 1 of 23 Background: Line #23 runs from the valve block on the driver's

More information

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web: Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748 Garching

More information

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14 Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION

More information

1.5 PODIUM C PERFORMANCE SERIES OWNERS MANUAL

1.5 PODIUM C PERFORMANCE SERIES OWNERS MANUAL 1.5 PODIUM C PERFORMANCE SERIES OWNERS MANUAL Contents CONGRATULATIONS...3 CONSUMER SAFETY...3 UNDERSTANDING THE 1.5 PODIUM C...4 READING THE SPRING RATE...5 LOW SPEED COMPRESSION ADJUSTER (LSC)...5 INSTALLING

More information

Brake Caliper Rebuild - Part Numbers & Tips Per Jim Millet, 3/15/2005

Brake Caliper Rebuild - Part Numbers & Tips Per Jim Millet, 3/15/2005 Per Jim Millet, 3/15/2005 Not too difficult a job. Rears are easier than fronts to access. You ll need the following gasket sets: Front caliper gasket set, P/N 34 11 1 157 037, MSRP $13.58 Rear caliper

More information

INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE CROSS COUNTRY / CROSS ROADS / HARD BALL RAKE KIT

INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE CROSS COUNTRY / CROSS ROADS / HARD BALL RAKE KIT INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE CROSS COUNTRY / CROSS ROADS / HARD BALL RAKE KIT Thank you for choosing the Motor Trike Cross Country / Cross Roads / Hard Ball rake kit. We ask that you read

More information

2018 Super Deluxe. service manual. GEN Rev D 2018 SRAM, LLC

2018 Super Deluxe. service manual. GEN Rev D 2018 SRAM, LLC 2018 Super Deluxe service manual GEN.0000000005317 Rev D 2018 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects

More information

PSYLO & DUKE U-TURN SPRING SERVICE GUIDE

PSYLO & DUKE U-TURN SPRING SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Contact your local distributor or visit the RockShox website at www.rockshox.com

More information

WARRANTY INFORMATION AMERICAN MADE MANITOU SUSPENSION

WARRANTY INFORMATION AMERICAN MADE MANITOU SUSPENSION AMERICAN MADE MANITOU SUSPENSION CONGRATULATIONS ON CHOOSING THE LATEST IN SUSPENSION TECHNOLOGY AVAILABLE, A 2003 MANITOU DORADO FORK BUILT IN THE USA. This DORADO fork is fully assembled and is ready

More information

Monarch Plus RC3/R. Service Manual. GEN Rev B 2016 SRAM, LLC

Monarch Plus RC3/R. Service Manual. GEN Rev B 2016 SRAM, LLC Monarch Plus RC3/R Service Manual GEN.0000000004938 Rev B 2016 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects

More information

Torqueflite Manual/Automatic Valve Body

Torqueflite Manual/Automatic Valve Body TCI 122400 Torqueflite Manual/Automatic Valve Body This valve body can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts

More information

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS

More information

70/82 SERIES SHOCK TECHNICAL MANUAL

70/82 SERIES SHOCK TECHNICAL MANUAL 70/82 SERIES SHOCK TECHNICAL MANUAL Item Part No. DESCRIPTION Item Part No. DESCRIPTION 1 9007-106 Snap ring 18 9053-120 6" compression tube (82/70) 2 SIB8-101PK Bearing/snap ring kit 18 9053-115 7" compression

More information

A-320 Balanced 1st Stage

A-320 Balanced 1st Stage Technical Manual A-320 Balanced 1st Stage A Manual for Repair and Maintenance Technicians View: Select Full Screen mode to use page arrows. FEATURES Extra durable satin chrome plated brass body. Fully

More information

Monarch. RT3/R Service Manual. GEN Rev B 2016 SRAM, LLC

Monarch. RT3/R Service Manual. GEN Rev B 2016 SRAM, LLC Monarch RT3/R Service Manual GEN.0000000004932 Rev B 2016 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects

More information

page 3 SCRATCH COIL 9, SCRATCH COIL 7

page 3 SCRATCH COIL 9, SCRATCH COIL 7 SCRATCH SUSPENSION SETUP GUIDE page 2 SCRATCH Air 8, Scratch AIR 6 page 3 SCRATCH COIL 9, SCRATCH COIL 7 page 4 Coil fork setup page 5 Coil SHOCK setup Suspension Setup Guide (Scratch 9, Scratch 7) Bike

More information

2019 PIKE & Revelation

2019 PIKE & Revelation 2019 PIKE & Revelation service manual GEN.0000000005683 Rev B 2018 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from

More information

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts!

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts! 2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit

More information

BICYCLE SHOCKS SERVICE MANUAL

BICYCLE SHOCKS SERVICE MANUAL 2001 BICYCLE SHOCKS SERVICE MANUAL www.foxracingshox.com Copyright 2001 by Fox Factory Inc. 1 2 TABLE OF CONTENTS Policies and Shared Procedures 1. Policies and Warranty Procedures - Page 4 2. Reducers

More information

TOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation

TOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation TOYOTA TUNDRA 2007- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-34070 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake

More information

Rebuilding the HE-120 Redrive

Rebuilding the HE-120 Redrive Rebuilding the HE-120 Redrive Rick Cavallaro Disclaimer: I am NOT an expert mechanic. If something looks or sounds wrong in these directions, it probably is. I d be happy to receive any tips or feedback

More information

Owners Manual Öhlins road & track front fork FG 43 Including:

Owners Manual Öhlins road & track front fork FG 43 Including: Owners Manual Öhlins road & track front fork FG 43 Including: Safety Adjusters Setting up your fork Changing springs Oil level adjustment Technical information Inspection & maintenance Service Tools 1

More information

Level 1 and Level 2/3 Fork Upgrade Fitting Instructions

Level 1 and Level 2/3 Fork Upgrade Fitting Instructions Fitting Instructions for Honda CB500X/F Level 1 and Level 2/3 Fork Upgrade Fitting Instructions Ensure bike is securely mounted on suitable stand or scissor lift, if our Engine Guard RRP 437, is fitted.

More information

REBUILD MANUAL FOR PRODIGY SHOCKS

REBUILD MANUAL FOR PRODIGY SHOCKS REBUILD MANUAL FOR 2.625 PRODIGY SHOCKS JUNE 2016 EDITION TOOLS NEEDED - 11/16 th wrench - FT LBS torque wrench - 3/8 ratchet with ¾ socket - ¼ ratchet with 9mm socket - 90 degree small pick - blue lok

More information

Sektor, Recon, 30 Gold, 30 Silver

Sektor, Recon, 30 Gold, 30 Silver Sektor, Recon, 30 Gold, 30 Silver Service Manual GEN.0000000004923 Rev A 2015 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to

More information

Mustang 7.5 Limited Slip Differential (28 Spline) V8; V6:

Mustang 7.5 Limited Slip Differential (28 Spline) V8; V6: Mustang 7.5 Limited Slip Differential (28 Spline) 79-85 V8; 86-10 V6: Required Tools: Ratchet Wrench Torque Wrench 1/2", 5/16, 3/4", 12mm and 15mm Sockets Lug nut Wrench Dial Indicator Digital Measuring

More information

Owner s Manual Wren Inverted Suspension Forks

Owner s Manual Wren Inverted Suspension Forks Owner s Manual Wren Inverted Suspension Forks with Keyed Stanchions TwinAir System Carbon Bash Guards 2 - Travel/AC Clips 2 - Hose/Cable Guides 43mm Uppers 36mm Stanchions Check out our service videos

More information

Slave Cylinder Weep Hole Drilling Procedure

Slave Cylinder Weep Hole Drilling Procedure Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key

More information

INSTALLATION GUIDE. RMS500, RMS501, RMS502, RMS503, RMS506, RMS507, RMS508, RMS509, -OR Manual Revision:

INSTALLATION GUIDE. RMS500, RMS501, RMS502, RMS503, RMS506, RMS507, RMS508, RMS509, -OR Manual Revision: REKLUSE MOTOR SPORTS z-start Brake Kit INSTALLATION GUIDE RMS500, RMS501, RMS502, RMS503, RMS506, RMS507, RMS508, RMS509, -OR 196-200 Manual Revision: 051309 2009 Rekluse Motor Sports Rekluse Motor Sports,

More information

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:

Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web: PRO/Comp Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748

More information

PS-Mustang-Strut. Strut; In-line or Remote, Single, Double, or Triple Adjustable TECHNICAL MANUAL

PS-Mustang-Strut. Strut; In-line or Remote, Single, Double, or Triple Adjustable TECHNICAL MANUAL PS-Mustang-Strut Strut; In-line or Remote, Single, Double, or Triple Adjustable TECHNICAL MANUAL Main Office 150 Franklin St. P.O. Box 1056 Reading, PA 19603 (610) 375-6180 (610) 375-6190 Fax Introduction

More information

Instructions for 4616 KYB shock rebuild and valve installation:

Instructions for 4616 KYB shock rebuild and valve installation: The goals of any suspension builder should be the same. That is to precisely build suspension in a repeatable, and efficient manner. All components must be modified so as to not threaten long-term component

More information

2004 SERVICE MANUAL Six Six Sport Avenue Stanford, Valencia, California fax

2004 SERVICE MANUAL Six Six Sport Avenue Stanford, Valencia, California fax 2004 SERVICE MANUAL Six Six Sport 28209 Avenue Stanford, Valencia, California 91355 661 257-4411 fax 661 294-4179 www.answerproducts.com Table of Contents Description Page Introduction 3 Front Suspension

More information

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT)

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets

More information

2019 Lyrik & Yari. service manual. GEN Rev A 2018 SRAM, LLC

2019 Lyrik & Yari. service manual. GEN Rev A 2018 SRAM, LLC 2019 Lyrik & Yari service manual GEN.0000000005684 Rev A 2018 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects

More information

TSS Fit Kit Installation Instructions Timbersled Snow Bike System

TSS Fit Kit Installation Instructions Timbersled Snow Bike System TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for

More information

2016 Lyrik. Service Manual. GEN Rev C 2016 SRAM, LLC

2016 Lyrik. Service Manual. GEN Rev C 2016 SRAM, LLC 2016 Lyrik Service Manual GEN.0000000005042 Rev C 2016 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects in

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

PIKE, REVELATION

PIKE, REVELATION 2019-2020 PIKE, REVELATION SERVICE MANUAL GEN.0000000005894 Rev A 2019 SRAM, LLC SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free

More information

H31 BOOSTER REBUILD & MASTER CYLINDER

H31 BOOSTER REBUILD & MASTER CYLINDER 2010 1991 BMW 750iL George Fontes gajfontes@yahoo.com H31 BOOSTER REBUILD & MASTER CYLINDER Rebuild hydraulic booster and replace Master Cylinder. Page 1 of 16 Master Cylinder Removal & Brake Booster Rebuild

More information