How to Fix the Altitude Clutch Problem in the Meade DS Mount By John Zimmerman September 2005
|
|
- Anna Curtis
- 6 years ago
- Views:
Transcription
1 How to Fix the Altitude Clutch Problem in the Meade DS Mount By John Zimmerman September 2005 Note: I claim no personal credit for the solution described here. Other DSX owners, whose real names I do not know, have posted messages on Yahoo and Cloudy Nights discussing this problem. Even the pictures are borrowed from those individuals. The Meade DS mount has a known problem with the altitude clutch assembly. When the clutch is tightened, it places a great deal of torque on a small slip ring that fits into a groove that holds everything together. Eventually, the slip ring slips out of the groove, and the scope will no longer move in altitude, even thought the motors are running. The solution presented here is to replace the small slip ring with something much larger. 1. Begin by disassembling the fork arm assembly: 2. Remove the tube from the L shaped support. 3. Remove the L shaped support by removing the 4 screws holding it. Note that the lower right screw is slightly longer than the other 3. Remember this when you go to reattach it. 4. Looking at where the L shaped bracket connected to the arm, you'll see a hole, and there should be a nut visible. Hold the nut with a pair of pliers, and unscrew the altitude lock. Behind the nut is a triangular shaped piece of aluminum that is also threaded onto the same shaft as the nut - it should come off also. This piece of aluminum, with its 3 prongs, is what provides the locking mechanism by pressing against the side of a large nylon gear you'll see later. 5. Now, facing the fork arm from the altitude lock side, pull the altitude lock out - the threaded shaft the nut and aluminum clutch were threaded on is attached to the lock. Note that there is a small nylon sleeve that fits over the shaft at the knob end - don't lose it. 6. There is a flat nut behind the altitude lock with two flattened sides that is threaded onto a shaft - the nut holds the declination circle in place. Unscrew the nut - a large crescent wrench is good for this. 7. Carefully pry the declination circle off of the shaft.7. Behind the declination circle is another, larger nylon sleeve. Carefully remove this by pulling it straight out. -1-
2 8. You should see two small screws that hold the large plastic fork decorative cover to the metal arm. Remove these two screws, and carefully remove the cover. Note that the cover is a bit tricky to put back on - you have to carefully seat it on the lower part of the fork arm before screwing it back to the upper part. 9. Now, back to the side of the fork where you removed the L bracket. Pull straight back on the large plastic ring that was part of the assembly the L support attached to. The disassembled components are shown in the picture below: From left to right the altitude lock knob, nut with flattened sides, declination circle, nylon sleeve, nut with flattened sides, large nylon gear/plastic ring assembly, 3 pronged triangular aluminum piece, lock nut, and tube cradle. A close up of the shaft with the slip ring is shown in the picture on the next page: -2-
3 If you look closely at the picture, the slip ring fits into a small groove just outside of the metal washer. If your scope has stopped moving in altitude in spite of the sound of running motors and a tight clutch, chances are this ring slipped out of the groove and has moved toward the right hand end of the shaft. What this does is because the large gear to move along the shaft and lose contact with the worm drive that turns it. The reason this ring slips out is because of the tremendous amount of pressure exerted against it when you tightened the altitude lock. The quick fix is to simply move the slip ring back into the groove. Unfortunately, it will likely slip over and over. To fix the problem, replace the small slip ring with something more substantial, as shown in the photos on the next page. The first photo shows the original slip ring, and one style that can replace it. The second photo shows a more substantial ring. These can be obtained at most hardware stores that have a good selection of fasteners and other small items. -3-
4 Removing the existing slip ring isn t too difficult, especially if it has already slipped out of its groove. Installing a new ring can be challenging. The second ring shown may require a special tool. I installed the first ring, which was possible with a large pair of pliers. -4-
5 Putting it all back together is pretty much the reverse of how you took it apart. Pay attention to the two plastic rings to the left of the large gear. They fit a certain way to provide the altitude stops, and they also slide back into the fork in a specific orientation. It's a good idea to have the altitude orientation pointing all the way down so you'll have a point of reference for reattaching the declination circle and the L shaped bracket. An additional thing I did as to cut and glue small pieces of #60 sandpaper to the end of each of the 3 prongs in the triangular aluminum piece that engages the nylon gear. The idea is these will provide for more of a friction fit. Finally, I keep the altitude axis locked all of the time, moving the tube only with the hand controller. This minimizes the chance for things to work their way loose. -5-
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationHow to replace or adjust the altitude clutch of the NexStar N11GPS
Langenbrettach/Germany, February 10 th 2004 Matthias Bopp How to replace or adjust the altitude clutch of the NexStar N11GPS Table of content How to replace or adjust the altitude clutch of the NexStar
More informationCorvette Set Separator (Glove Box) Lock Removal
1956-62 Corvette Set Separator (Glove Box) Lock Removal The materials here were gathered from several Corvette Forum Threads as well as from the Web Pages of Rich Mozzetta (rich5962 on the CF). Our colleagues
More informationRemoving Original Rod
Congratulations on your purchase of the Golden Rod tm. We wish you many miles of crisper, more precise shifting. Everything is done via the underside of the car; nothing inside the car needs to be touched.
More informationSwitchback Carrier Rack System
Switchback Carrier Rack System Installation Instructions 1 Rocky Mountain Westy Ph. (970)310-3441 Introduction Thank you for purchasing the Rocky Mountain Westy Switchback Carrier Rack System. We pride
More informationFord F-150 Speaker Replacement Instructions
Ford F-150 Speaker Replacement Instructions This article was downloaded from http://www.fordf150.net Be sure to go there to view and download the other how-to articles. Thanks to John Meyer for contributing
More informationRAMPAGE POWER LIFT RAMP
RAMPAGE POWER LIFT RAMP INSTALLATION AND OPERATING INSTRUCTIONS (3/10/07) The Rampage Power Lift Ramp is the fast, easy, and safe way to load a motorcycle into a truck. One person can load or unload a
More informationHow to Replace the Main Axle Gear on the Bachmann Spectrum GScale using the NWSL # upgrade gear.
How to Replace the Main Axle Gear on the Bachmann Spectrum GScale 4-4-0 and 2-6-0 Mogul (2001era), using the NWSL #2223-6 upgrade gear. By Paul M. Newitt (all text and photos Copyright Paul M. Newitt,
More informationHow I Installed the Edgerider Wheels on my Gammill Classic Plus
How I Installed the Edgerider Wheels on my Gammill Classic Plus Jeffrey Lomicka May 15, 2004 I'd been looking forward to installing these wheels since I tried them this year at MQX. This is my pictorial
More informationJRSC + BBK Install on SVTF. Neil A. Shah medicnas on focaljet September 2006
JRSC + BBK Install on SVTF Neil A. Shah medicnas on focaljet September 2006 ECU up here. When removing make sure the smaller bundles of wires don t get wrapped around the bottom edge and break - this almost
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationFigure 1: Valve housing smooth vs. o-ring groove
If you are driving an older Corvette, and by that I mean a C2 or C3, it will eventually get to a point where the Power Steering Control Valve (PSCV) will leak and require attention. In 2002, I had to repair
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationMaximum Motorsports Camber Caster Plates (05-10):
Maximum Motorsports Camber Caster Plates (05-10): Tools Required: Lug Wrench 21mm Deep Socket 18mm Deep Socket 15mm Deep Socket 17mm Socket 13mm Socket 10mm Socket Torque Wrench (requires 166lb-ft capacity
More information13 March F Dodge Adjustable Track bar with Relocation Bracket (I-00201) 1
13 March 2014 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket (I-00201) 1 BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 P/N# 1032011-F UPLEASE READ ALL INSTRUCTIONS
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationGlobal West Suspension 655 South Lincoln Ave San Bernardino Ca Phone Fax Web address globalwest.
Global West Suspension 655 South Lincoln Ave San Bernardino Ca. 92408 Phone 877-470-2975 Fax 909-890-0703 Web address globalwest.net Mustang coilover instruction sheets for 64-66 Kit includes the following
More informationPorsche 928 with 16v LH-Jetronic Fuel System
Porsche 928 with 16v LH-Jetronic Fuel System Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 1992-2005 325, 323, 318 and 1986-1994 525, 528, 535, 540 5-speed models only. (part number USSE3 and USSE5) Thank you
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationRekluse Motor Sports. The ProStart Clutch. H-D Sportster (2004 +)
Rekluse Motor Sports The ProStart Clutch H-D Sportster (2004 +) Installation Guide Copyright 2006 Rekluse Motor Sports ProStart Revision 1.000 RMS687 H-D Sportster 195-687 Manual Revision: 111308 Rekluse
More informationBMW E61 Hydraulic Pump replacement instructions
BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More informationKodak 750H Carousel Projector Repair
Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, 3-26-2016 Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors
More informationSpecial Note About The JDM High Performance Water Pump:
Page 1 of 30 JDM Engineering, Inc. home Call Us! 732-780- 0770 back to Installation Instructions Electric Fan Upgrade Kit Electric Fan Wiring Diagram Thank you for your purchase of the JDM Engineering
More informationPT 709 firing pin and extractor removal. Disclaimer: My Taurus manual says not to take this apart (just flush it with cleaner).
PT 709 firing pin and extractor removal. Disclaimer: My Taurus manual says not to take this apart (just flush it with cleaner). But several list members have done this without ill effect. So here goes:
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationEurocompulsion Camshaft Installation
Eurocompulsion Camshaft Installation Introduction, please read. The purpose of this article is too assist our customers with installation of a performance camshaft in the Fiat Multiair 1.4 Turbo. The operation
More informationLAMBO VERTICAL DOOR HOW TO GUIDE
-1 LAMBO VERTICAL DOOR HOW TO GUIDE Despite what you may believe, scissor doors are not that difficult to install. There are plenty of body shops out there that will charge you $2,000 - $10,000 for this
More informationRebuilding the HE-120 Redrive
Rebuilding the HE-120 Redrive Rick Cavallaro Disclaimer: I am NOT an expert mechanic. If something looks or sounds wrong in these directions, it probably is. I d be happy to receive any tips or feedback
More informationDIY: Repairing/Replacing the Timing Chain Tensioner
DIY: Repairing/Replacing the Timing Chain Tensioner By Saki GT - February 8, 2012 [youtube=http://www.youtube.com/watch?v=24cil5_9yvq] The above video is an example of how a bad Timing Chain Tensioner
More informationYOU MAY WANT TO FIRST TRY TO LOOSEN THE FILTER HOUSING
2005 XC90 Tune-up (5-cyl) Including: Oil Change - Spark Plugs - Fuel Filter - Cabin Filter First off - let me say that I am an amateur (at best) mechanic, and I claim no responsibility for whatever you
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationMityvac MV8000 O-ring Replacement
A vacuum pump must be air tight in order to operate. A leak in your vacuum pump will potentially complicate the diagnosis of vacuum systems or make bleeding automotive fluids more difficult. Learn to replace
More informationHURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance
FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.
More informationModdit. How to Install an OS Giken Differential into a
Moddit How to Install an OS Giken Differential into a Subaru BRZ This guide goes over the steps necessary to remove and install the OS Giken Limited Slip Differential into a Subaru BRZ. This guide may
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More information001-Component-build. Build the following Contraptor components before assembly:
001-Component-build Build the following Contraptor components before assembly: http://www.contraptor.org/make-linear-rail-v2#assembly http://www.contraptor.org/make-linear-bearings-v2#assembly http://www.contraptor.org/make-sliding-elements#assembly
More informationFisher 657 Diaphragm Actuator Sizes and 87
Instruction Manual 657 Actuator (30-70 and 87) Fisher 657 Diaphragm Actuator Sizes 30 70 and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Installation... 3 Mounting
More informationADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12
Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD
More informationPlease try our way first.
1958-1962 Corvette Raingear installation instructions Designer s Note: The 1958-1962 Corvette RainGear wiper system that you have purchased is complex and will require patient fitting. Complete Instructions
More informationASTRO-PHYSICS 600E GERMAN EQUATORIAL MOUNT (600HDA) WITH DUAL AXIS STEPPER MOTORS AND 8010 CONTROLLER
ASTRO-PHYSICS 600E GERMAN EQUATORIAL MOUNT (600HDA) WITH DUAL AXIS STEPPER MOTORS AND 8010 CONTROLLER MODEL 600HDA (600E) PARTS LIST 1pc. 600E HDA Equatorial Head with stepper motors on right ascension
More informationRedlineGoods Tacoma Installation Manual
RedlineGoods 2016+ Tacoma Installation Manual AUTOMATIC SHIFT BOOT AND EBRAKE BOOT Press down on the factory shift boot collar to disconnect it from the shift knob. Unscrew shift knob Pull up on the rear
More informationT3 SERVICE HANDLE SERVICE
The handle assembly contains many critical parts that allow proper function of the T3 tool. The handle assembly contains the fuel valve, spark unit, battery contacts and many other critical components.
More information1209A GM B-BODY Double Adjustable Trailing Arms
1209A 78-96 GM B-BODY Double Adjustable Trailing Arms Warning: This installation should be performed by a trained professional. Tools Required for this Installation - 4 post lift or alignment rack preferable
More informationJ30 Fuel Injector Replacement w/o Removing the Plenum As contributed by NICO member Chris Fowler
J30 Fuel Injector Replacement w/o Removing the Plenum As contributed by NICO member Chris Fowler Removing a fuel injector without removing the plenum isn t without risk. Grinding of the upper plenum will
More informationOperator s Manual. Single Hand Manual Drive Wheelchair
Operator s Manual Single Hand Manual Drive Wheelchair Jordan R. Smith Kayla Gosse Leah McElhaney Team #5 Project for Client: Danielle Giroux Client Contact Information: Dave and Suzanne Giroux 53 Charlotte
More informationCLUTCH-04, Clutch Master Cylinder Replacement
CLUTCH-04, Clutch Master Cylinder Replacement Introduction This procedure details replacement of the clutch master cylinder on 944s and 968s. Terry Jenner did a great job with this procedure. He wrote
More informationAuthor: Quicksandfarmer Editor: jbrukardt
Author: Quicksandfarmer Editor: jbrukardt Jinma Splitting Guide Rev 0.1 7/29/2014 Table of Contents Introduction... 3 Gather the appropriate tools:... 4 Part I: Preliminaries... 5 Part II: Disassembly...
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SP.
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X
More informationLMB-C6 CF Senior Member
LMB-C6 CF Senior Member Rotor install DIY... ****** FRONT: ****** Remove the wheel. To remove the rotor you need to remove the caliper and the bracket. There are 2 bolts for the caliper (top smaller bolt
More informationRestoring the Strategic Air & Space Museum s E-4B Model
Restoring the Strategic Air & Space Museum s E-4B Model By Don Joy IPMS Fort Crook I received a request from the SASM (Strategic Air and Space Museum) to do a restoration of the model. They had a member
More informationRepairing SpeedTreater-TX Spray Proximity Sensor
Repairing SpeedTreater-TX Spray Proximity Sensor How to remove and replace the proximity sensor on the spray valve assembly. 2017 guides.equipmentzone.com Page 1 of 9 Step 1 Unscrew and Remove Top Cover
More information2010 BMW S1000RR TracStar HeliBars TS mm taller (1.7 ) ~ 20mm Rear Offset (.8 ) ~ Stock Width (25 ¼ )
WARNING: IMPROPER INSTALLATION COULD RESULT IN SERIOUS INJURY OR DEATH. HAVE A QUALIFIED MECHANIC INSTALL YOUR HELIBARS. Right Side To protect your motorcycle during installation place clean shop rags
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationOpenROV. Tether Reel from Cheap Extension Cord Reel
OpenROV Tether Reel from Cheap Extension Cord Reel In this guide I will show you the steps I took to modify a cheap extension cord reel into a tether reel. Written By: Brett Forsyth 2017 openrov.dozuki.com
More informationService Information Chevrolet Camaro 3.6L LFX Engine. Camshaft Position Actuator Replacement - Bank 1. Document ID:
Service Information 2014 Chevrolet Camaro 3.6L LFX Engine Camshaft Position Actuator Replacement - Bank 1 Document ID: 2900815 Special Tools Removal Procedure EN49982-1 Timing Chain Retainer EN49982-2
More informationINSTALLATION INSTRUCTIONS Horizon CCR HZ13054
INSTALLATION INSTRUCTIONS Horizon CCR HZ13054 IMPORTANT: PLEASE GIVE CUSTOMER ENCLOSED INFORMATION! Thank you for your purchase of our HeliBars. They are designed to increase your long distance comfort
More informationSteering Damper for FLH Harley-Davidson Bikes/Trikes
Steering Damper for FLH Harley-Davidson Bikes/Trikes I have spoken with several HD Touring model trikers, who are looking for increased feel in the steering department. Some want to cure a slight wobble
More informationM3 Design Product Teardown Kobalt Double-Drive Screwdriver
19 Jun, 2013 Why do the product teardowns? M3 Design Product Teardown Kobalt Double-Drive Screwdriver Part of the product development process is to apply knowledge gained from prior experience during the
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationPERKINS Fitting new rear oil seal and crank case gaskets
PERKINS 4108 Fitting new rear oil seal and crank case gaskets Near the end of this summer the 24 year old Perkins on my Morgan 384 decided to misbehave. First the solenoid on the starter motor, then the
More information05/06 Gsxr 1000 Clutch Mod
By: Ali (Jetspeedz) 05/06 Gsxr 1000 Clutch Mod Parts: 21472-41G10 - WASHER, CLUTCH - $10.09 From 06 Gsxr 750 Opt: 11482-40F00 - GASKET, CL COVER - $8.29 Tools: 13/64 Drill bit, 30mm, 12mm, 10mm, 8mm sockets,
More informationInstallation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog #
Installation Instructions INDY SHIFTER Fits: 2015-2018 Mustang Fastback & Convertible with MT-82 Transmission Catalog # 3916036 Watch our installation video on YouTube WORK SAFELY! For maximum safety,
More informationAZIMUTH TRACKING ERROR FRICTIONAL DRAG & MOTOR LOAD
AZIMUTH TRACKING ERROR - - - FRICTIONAL DRAG & MOTOR LOAD Motor loading and friction drag caused by bushing slop and poorly fitted unpolished parts has been found and identified in 8 places within the
More informationGrilleGuy.com, LLC. Installation Instructions and Care guide : Scion tc : Honda S2000 : Honda Civic
Installation Instructions and Care guide : 2005 2009 Scion tc : 2000 2003 Honda S2000 : 2004 2005 Honda Civic Thanks again for purchasing your custom grille insert from the GrilleGuy. The following are
More informationFD Transmission Rebuild: Parts Inspection
FD Transmission Rebuild: Parts Inspection Now that everything is disassembled, cleaned, and bagged in labeled Zip-Locs, it s time to decide what to replace. Warning: I m not a transmission specialist I
More informationCold Air Intake Installation Instructions
BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions PARTS LIST: PF BMWE36-4 PROCEDURE: 1. Using a flat-head screwdriver, loosen the hose clamp between the AFM and rubber boot leading to engine
More informationWe recommend installing the TRS Racebars first as we have done
Thanks for purchasing the 2 Front Lowering Kit for the Honda Grom (MSX125). This is a basic installation guide, and we tried to cover everything, but use your best judgment along the process. It is recommended
More informationM1A1 Thompson Upgrade
M1A1 Thompson Upgrade If you are mechanically inclined at all. This should be no problem. I'll start off with a list of things you will need. Thompson M1A1 Whisky Cigarettes Tools: Flat screwdriver No.
More informationChevrolet Generator Rebuild and Restoration
Rich Mozzetta PDF compiled by Dave Zuberer Chevrolet Generator Rebuild and Restoration I had 2 old Chevy generators and I used parts from both to create a new one for a 1960 Corvette project. Both generators
More informationSpeedometer Repair & Lube Pt.1
Speedometer Repair & Lube Pt.1 1. Begin disassembly on a clean area approximately 2' by 3' so you have plenty of room to layout parts as you disassemble them. I use a piece of white or light colored paper
More informationServicing a Katadyn PUR40E
Servicing a Katadyn PUR40E ABOUT THE ASSOCIATION OF OCEAN ROWERS The Association of Ocean Rowers is open to anyone interested in the sport of Ocean Rowing. It is strictly independent of all other bodies
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More information1967 (Late) CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 03SE2012 1967 (Late) - 1968 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationACE 325/570 2 Lift Kit
ACE 325/570 2 Lift Kit Polaris Ace 325/570 2014+ Part #: 5101244 Rev. 082316 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING RT Pro
More informationEURO HEADLIGHT ADJUSTER REMOVAL AND INSTALLATION
EURO HEADLIGHT ADJUSTER REMOVAL AND INSTALLATION This document is a step by step explanation of how to remove and replace the headlight adjusters in the Euro headlights. Parts needed to repair both headlights:
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0925 APPLICATION 2011-12 E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler Congratulations for being selective enough
More information2000 Mr2 Spyder Seat Cover Replacement Project
2000 Mr2 Spyder Seat Cover Replacement Project Tool List: Plastic Trim Tool, Hog Ring Pliers, Medium or Heavy Duty Wire Cutters, 12mm socket, 14mm Socket, Ratchet, Extension, Flat Head Screwdriver & Gloves
More informationAll of the control valves that we install the Mk. 16IQ positioner on are factory calibrated for proper operation prior to shipment.
1 Troubleshooting The first thing you need is information... Try to find out what is wrong and why. Getting a serial number (found on the valve tag (see above)) and application parameters are always helpful
More informationRekluse Motor Sports. The ProStart Clutch. H-D Big Twin ( )
Rekluse Motor Sports The ProStart Clutch H-D Big Twin (1990 1997) Installation Guide Copyright 2006 Rekluse Motor Sports ProStart Revision 1.000 RMS680 H-D Big Twin 195-680 Manual Revision: 121206 Rekluse
More information1 August Dodge Adjustable Track bar with Relocation Bracket 1
1 August 2017 1032011-1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 DOWNLOAD ENHANCED INSTALL MANUALS AT BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 Dodge 1500
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0924 APPLICATION: 2011-12 E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler Congratulations for being selective enough
More informationAudi B7 A4 Street Shield Skid Plate Installation Instructions
Audi B7 A4 Street Shield Skid Plate Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those
More informationLooking up the front of the engine from under the radiator. (Picture taken with belt under tension.)
8. If you re replacing the AC compressor drive belt as well, it s time to loosen its belt tensioner. The AC compressor belt tensioner is very obvious under the front of the car. Loosen the 13mm bolt, then
More informationI-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationDIY: Shiver Valve Check, Illustrated
DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover
More information