GENUINE PARTS INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "GENUINE PARTS INSTALLATION INSTRUCTIONS"

Tyler Russell Allison
6 years ago
Views:

GENUINE PRTS INSTLLTION INSTRUCTIONS 1. 2. 3.

TOOLS REQUIRED: Flathead screwdriver Masking Tape Needle nose pliers Clip Remover Torx PRE-INSTLLTION CUTIONS/NOTES:

INSTLLTION PTTERN: 62310 5C1(ICC & FE,W CMER,W SONR) F2310 5C1 (ICC & FE,W CMER,W SONR) 8.

1 GENUINE PRTS INSTLLTION INSTRUCTIONS DESCRIPTION: PPLICTION: PRT NUMER: Sport Grille (ICC & FE) Q60 F2310 5C1 (ICC & FE,W CMER,W SONR) 4. KIT CONTENTS: Item Qty. Description Part Number 1 Sport Grille (ICC & FE) N/ 1 Installation Instruction Replacement Template 999V2 W TOOLS REQUIRED: Flathead screwdriver Masking Tape Needle nose pliers Clip Remover Torx PRE-INSTLLTION CUTIONS/NOTES: Dealer Installation Recommended. 10mm Socket & Driver 7. INSTLLTION PTTERN: C1(ICC & FE,W CMER,W SONR) F2310 5C1 (ICC & FE,W CMER,W SONR) 8. INSTLLTION PROCEDURE: pply masking tape to bumper Fig 1 1) Open the vehicle engine hood. 2) pply masking tape to front fender, head lamp and bumper, around the grille, to prevent scratches. 3) Keep turning the wheel to the left or right direction. 4) Disconnect the vehicle battery (negative terminal). pply masking tape to fender and head lamp Page 1 of 6 F2310 5C1 II Rev. 03/01/16

INSTLLTION PROCEDURE: Clip ir duct Fig 2 5) Remove 10 clips that attach air duct to the vehicle (Keep to reuse).

Clip (Cross type) : 4 Clips Clip (Triangle type) : 6 Clips Fig 3 6) Detach the front end of a claw of the fender side seal by pulling

View Fig 4 Fender side seal 7) While pulling upward the fender side seal, detach screw that attaches a front bumper side bracket and

2 INSTLLTION PROCEDURE: Clip ir duct Fig 2 5) Remove 10 clips that attach air duct to the vehicle (Keep to reuse). The clip must be careful because the two kinds. Clip (Cross type) : 4 Clips Clip (Triangle type) : 6 Clips Fig 3 6) Detach the front end of a claw of the fender side seal by pulling upward. For degradation Hand, or clip remover use. View Fig 4 Fender side seal 7) While pulling upward the fender side seal, detach screw that attaches a front bumper side bracket and remove the bracket (Keep to reuse). racket umper side bracket Fig 5 8) Detach 6 screws on under cover (Keep to reuse). 9) Detach 4 screws on fender protector on each side (Keep to reuse). The clip must be careful because the two kinds. (Without cross hole) : 6 s (With cross hole) : 4 s Under cover Fender protector Page 2 of 6 F2310 5C1 II Rev. 03/01/16

3 INSTLLTION PROCEDURE: Fender protector Fig 6 10) Detach clip in the wheel house (Keep to reuse) and pull the fender protector to backward. clip Pull backward View Fig 7 (after pulling fender protector out) 11) Detach screw which is behind the front bumper (Keep to reuse). Front bumper 3 C Fig 8 12) Detach the bumper fascia from the claws of vehicle fender and head lamp by pulling in the direction of the arrow 1,2 and View C Fig 9 13) During pull bumper forward, pull off the FOG connector. FOG connector Page 3 of 6 F2310 5C1 II Rev. 03/01/16

View D Fig 16 16) Disconnect the front view camera harness connector.

4 INSTLLTION PROCEDURE: Fig 14 14) During pull MPR forward, pull off the for MPR harness connector in RH side. D Fig 15 15) Remove the bumper from the vehicle. View D Fig 16 16) Disconnect the front view camera harness connector. Camera harness connector Fig 17 17) Disconnect the sonar and sonar harness connector. sonar and sonar harness connector. Page 4 of 6 F2310 5C1 II Rev. 03/01/16

INSTLLTION PROCEDURE: Fig 18 18) Remove the sonar harness from grille.

Nut Claw Fig 20 20) y hand, unhook the grille 8 claws from the bumper and slowly

Claw Fig 21 Camera kit 21) Remove 2 screws on camera kit and detach camera kit

5 INSTLLTION PROCEDURE: Fig 18 18) Remove the sonar harness from grille. (LH/RH both sides.) Fig 19 19) Remove 12 nuts that attach the radiator grille. Nut Claw Fig 20 20) y hand, unhook the grille 8 claws from the bumper and slowly remove the grille by pulling the grille away from bumper. Claw Fig 21 Camera kit 21) Remove 2 screws on camera kit and detach camera kit (Keep to reuse). 22) Install camera kit with 2 screws to Sport Grille (ICC & FE). Page 5 of 6 F2310 5C1 II Rev. 03/01/16

6 INSTLLTION PROCEDURE: Sport Grille (ICC & FE) Fig 22 23) lign Sport Grille (ICC & FE) claws to the holes in bumper. 24) Push Sport Grille (ICC & FE) against the bumper until claws are fully inserted and locked. 25) Fix Sport Grille (ICC & FE) with nuts that were removed in 19). 26) Reinstall all removed connector in reverse order. 27) Reinstall all removed parts in reverse order. Refer to REMOVL ND INSTLLTION (FRONT UMPER) : Check Clearance and Surface Height Difference. 27) Connect the vehicle battery (negative terminal.) 28) Remove any remaining masking tape. 29) Close the vehicle engine hood. 30) Perform camera image calibration. Refer to CLIRTING CMER IMGE (ROUND VIEW MONITOR) : Special Repair Requirement. Verify re-installed parts for proper flush fit Please carry out lighting confirmation of Fog Lamp. Please carry out icc calibration. Page 6 of 6 F2310 5C1 II Rev. 03/01/16

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PRTS INSTLLTION INSTRUCTIONS 1. 2. 3. DESCRIPTION: PPLICTION: PRT NUMER: Radiant Grille Emblem Q60 F2310 5C0K (RGE,W/O CMER,W/O SONR) 4. KIT CONTENTS: Item C Qty. Description Part Number 1 Radiant