PARTS LIST TRAILER BRAKE SYSTEMS. LIT NO: DATE: October 2017 REVISION: H

Size: px

Start display at page:

Download "PARTS LIST TRAILER BRAKE SYSTEMS. LIT NO: DATE: October 2017 REVISION: H"

Gilbert Gaines
6 years ago
Views:

1 PARTS LIST TRAILER BRAKE SYSTEMS LIT NO: DATE: October 07 REVISION: H

2 TABLE OF CONTENTS INTRODUCTION ABBREVIATIONS DRUM BRAKES & 6. DRUM FOUNDATION BRAKE HXS Brakes P-TYPE DRUM FOUNDATION BRAKE 7 INTRAAX DRUM BRAKE ACTUATION ENCLOSED S-CAM, EARLY TYPE (PRE-000) 8 INTRAAX DRUM BRAKE ACTUATION NON-ENCLOSED S-CAM EARLY TYPE (PRE-000) 9 INTRAAX DRUM BRAKE ACTUATION SEVERE DUTY CAM TUBE 0 INTRAAX DRUM BRAKE ACTUATION 6. SEVERE DUTY CAM TUBE DRUM BRAKE CHAMBER GENERAL INFORMATION INTRAAX Drum Brake Chamber Application DRUM BRAKE CHAMBERS SLACK ADJUSTERS DISC BRAKES TOOWOOMBA IRON HUB ROTOR KNORR-BREMSE BRAKE CALLIPER IDENTIFICATION Knorr-Bremse Brake Left & Right Calliper Identification 6 ConMet Brake Rotor Identification 7 Early Type Parallel Brake Rotor 7 Late Type Offset Brake Rotor 7 DISC BRAKE SYSTEM MAXXT. [SARN 76 FB] 8 DISC BRAKE CALLIPER MAXXT. [SARN 76 FB] 9 DISC BRAKE SYSTEM WABCO HTD [SARN 7 FB] 0 DISC BRAKE CALLIPER WABCO HTD [SARN 7 FB] DISC BRAKE SYSTEM WABCO HTD-0. [SARN 8 FB] DISC BRAKE CALLIPER WABCO HTD-0. [SARN 8 FB] DISC BRAKE SYSTEM KNORR-BREMSE. [SARN 98 FB] DISC BRAKE CALLIPER KNORR-BREMSE. [SARN 98 FB] DISC BRAKE CHAMBERS 6 SPECIAL TOOLS 7 Revisions Table Rev H

3 INTRODUCTION The purpose of this parts list is to document the repair parts, accessories and special tools available for the disc and drum brake systems installed to the Hendrickson INTRAAX family of axles as follows: Hendrickson Extended Service (HXS ) and conventional drum brake P-Type Drum Brake MAXXT Disc Brake Wabco HTD-77 and HTD-0 disc brake Knorr-Bremse disc brake NOTICE: All quantities listed within this parts list are as applicable for one axle assembly. ABBREVIATIONS Abbreviations used in this document include the following terms: AR As Required ADI Austempered Ductile Iron Exc Except HXS Hendrickson Extended Service brakes NLA No Longer Available NSS Not Serviced Separately PCD Pitch Circle Diameter Rev H

4 TRAILER BRAKE SYSTEMS PARTS LIST DRUM BRAKES Rev H 6

5 & 6. DRUM FOUNDATION BRAKE S-778- Brake Overhaul Kit, x 8-/8 HXS S-8- Brake Overhaul Kit, 6. x 7 Standard S-7- Brake Overhaul Kit, 6. x 7 HXS S-7- Brake Overhaul Kit, 6. x 8-/8 HXS S-7 Kit, Brake Hardware S Brake Dust Shield Kit Axle S Brake Dust Shield Kit Axle S Brake Dust Shield Kit.7 Axle SARN 67 FB. See box HXS Brakes. Includes brake hardware item. SARN 69 FB. See box HXS Brakes. Includes brake hardware item. Includes springs, rollers, bushes, pins & clips. Included in item. Includes dust shield, clamp, grommet & inspection plugs. S-77 Bracket, ABS Sensor Mounting Axle Suits 7 mm ( ) axle. S-877 Bracket, ABS Sensor Mounting.7 Axle Suits 6 mm (.7 ) axle. S-786 Brake Drum, x 8-/8 8 Stud 7 PCD CentriFuse Brake Drum, 6. x 7 0 Stud 8 PCD CentriFuse. D-0 Brake Drum, 6. x 7 0 Stud 8 PCD Cast. C-699 Brake Drum, 6. x 7 0 Stud PCD Cast Drum only. Included in Brake Drum, 6. x 7 Spoke HN hub & drum assembly Brake Drum, 6. x 8-/8 0 Stud 8 PCD Cast Brake Drum, 6. x 8-/8 0 Stud 8 PCD CentriFuse Brake Drum, 6. x 8-/8 0 Stud PCD Cast Clip, ABS Sensor Retainer Sensor, ABS HXS Brakes Hendrickson Extended Service (HXS ) brakes use thicker lining blocks, which extends the distance travelled between brake services. They can only be fitted to HXS S-cams because the throat is smaller to allow for the thicker linings. HXS S-cams have been standard on all Hendrickson axles since March 000 and are standard for replacement camshafts. They can be identified by the letters HXS stamped into the spine end of the S-cam. HXS brake shoes are prominently stamped with the letters HXS. Standard brake shoes can be fitted to Hendrickson HXS S-cams. HXS Standard Throat HXS Throat The end of the S-cam will be marked with the letters HXS Rev H

6 Rev H 6

7 P-TYPE DRUM FOUNDATION BRAKE S-778- Brake Shoe Overhaul Kit, x 8-/8 HXS S-8- Brake Shoe Overhaul Kit, 6. x 7 Standard S-7- Brake Shoe Overhaul Kit, 6. x 7 HXS S-7- Brake Shoe Overhaul Kit, 6. x 8-/8 HXS SARN 67 FB. See box HXS Brakes on page. Includes brake hardware item 7. SARN 69 FB. See box HXS Brakes on page. Includes brake hardware item 7. S-77 Bracket, ABS Sensor Mounting Axle Suits 7 mm ( ) axle. S-877 Bracket, ABS Sensor Mounting.7 Axle Suits 6 mm (.7 ) axle Sensor, ABS Clip, Retaining ABS Sensor S Kit, Dust Shield Axle Includes dust shield, clamp, S Kit, Dust Shield.7 Axle grommet & inspection plugs. 6 D-0 Brake Drum, 6. x 7 0 Stud 8 PCD Cast Brake Drum, 6. x 7 0 Stud 8 PCD CentriFuse. C-699 Brake Drum, 6. x 7 0 Stud PCD Cast Brake Drum, 6. x 8-/8 0 Stud 8 PCD Cast Brake Drum, 6. x 8-/8 0 Stud 8 PCD CentriFuse Brake Drum, 6. x 8-/8 0 Stud PCD Cast Kit, Brake Hardware Includes springs, pins, rollers, bushes, bolts, nuts, washers, plates & spacers Rev H

8 INTRAAX DRUM BRAKE ACTUATION ENCLOSED S-CAM, EARLY TYPE (PRE-000) A-08 Washer, Outer Slack Adjuster 6 A-08 Ring, Retaining Slack Adjuster A-60 Washer, Inner - S-Cam Shaft SA Screw, Flanged /8 x. 8 S-0 Support Bushing Assembly, S-Cam Kit, S-Cam Tube Nylon Includes grease nipple and O-ring. 7 SA Nut, Prevailing Torque /8 8 8 A-0808 Ring, Retaining S-Cam Shaft 9 A-0807 Seal, Brake Spider S-Cam Journal *See Note. Suits -7/8 journal. 0 C-07 Washer, S-Cam Under Head S-0-L S-Cam, Brake LH. HXS profile. brake with HXS S-cam profile. See S-0-R S-Cam, Brake RH. HXS profile. box HXS Brakes on page. S-66-L S-Cam, Brake LH. HXS profile. 6. brake with HXS S-cam profile. See S-66-R S-Cam, Brake RH. HXS profile. box HXS Brakes on page. S-08 Bush, Brake Spider S-Cam Journal *See Note. Suits -7/8 journal. NOTE: Enclosed S-Cam system is only suitable for INTRAAX axles with -7/8 journal and is not available for INTRAAX axles with journals Rev H 8

9 INTRAAX DRUM BRAKE ACTUATION NON-ENCLOSED S-CAM EARLY TYPE (PRE-000) A-08 Washer, Outer Slack Adjuster 6 A-08 Ring, Retaining Slack Adjuster A-60 Washer, Inner - S-Cam Shaft SA Screw, Flanged /8 x. 8 S-0 Support Bushing Assembly, S-Cam 6 SA Nut, Prevailing Torque /8 8 7 A-0808 Ring, Retaining S-Cam Shaft 8 A-0807 Seal, Brake Spider S-Cam Journal Suits -7/8 journal. S-88 Seal, Brake Spider S-Cam Journal Suits journal. 9 C-07 Washer, S-Cam Under Head 0 S-0-L S-Cam, Brake LH. HXS profile. brake with HXS S-cam profile. See box S-0-R S-Cam, Brake RH. HXS profile. HXS Brakes on page. S-66-L S-Cam, Brake LH. HXS profile. 6. brake with HXS S-cam profile. See S-66-R S-Cam, Brake RH. HXS profile. box HXS Brakes on page. S-08 Bush, Brake Spider S-Cam Journal Suits -7/8 journal. S-898 Bush, Brake Spider S-Cam Journal Suits journal Rev H

10 INTRAAX DRUM BRAKE ACTUATION SEVERE DUTY CAM TUBE S-0-L HXS S-Cam, Brake LH. HXS S-cam profile. See box HXS S-0-R HXS S-Cam, Brake RH. Brakes on page. S-706 Kit, Cam Tube Brake Overhaul Kit S-Cam & Tube, RH Overhaul Kit S-Cam & Tube, LH Overhaul Kit S-Cam & Tube, Axle Includes items tubes, seals, supports and associate hardware. Includes items & (S-0-R & S-706). Not illustrated. Includes items & (S-0-L & S-706). Not illustrated. Includes both items ( & ). Not illustrated Rev H 0

11 INTRAAX DRUM BRAKE ACTUATION 6. SEVERE DUTY CAM TUBE S-66-L HXS S-Cam, Brake LH HXS S-cam profile. See box HXS S-66-R HXS S-Cam, Brake RH Brakes on page. S-70 Kit, Cam Tube 6. Brake Overhaul Kit S-Cam & Tube, LH Overhaul Kit S-Cam & Tube, RH Overhaul Kit S-Cam & Tube, Axle Includes items tubes, seals, supports and associate hardware. Includes items & (S-70 & S-66-L). Not illustrated. Includes items & (S-70 & S-66-R). Not illustrated. Includes both items ( & ). Not illustrated Rev H

12 DRUM BRAKE CHAMBER GENERAL INFORMATION INTRAAX Drum Brake Chamber Application The applicable brake chambers for INTRAAX suspension systems are determined by the following: Slack adjuster length from the centre of the S-cam spline to the centre of the brake chamber clevis pin Pushrod length is measured in the caged position from the brake chamber mounting face to the end of the pushrod. It does not include the clevis. Brake chamber pushrod stroke Brake chamber pushrod length The common brake chamber applications to suit INTRAAX suspension system configurations are: AAT/AANT fitted with. & 6.0 slack adjusters utilise brake chambers with a. stroke and 0.0 rod length. AAT/AANT fitted with 6. & 7.0 slack adjusters utilise brake chambers with a.0 stroke and 8.6 rod length. AAL/EDL/EDT fitted with. & 6.0 slack adjusters utilise brake chambers with a. stroke and.6 rod length. AAL/EDL/EDT fitted with 6. & 7.0 slack adjusters utilise brake chambers with a.0 stroke and. rod length. DRUM BRAKE CHAMBERS Rev H

13 Brake Chamber, Type. rod, stroke Brake Chamber, Type 8 rod,. stroke. *See Note Brake Chamber, Type 8.6 rod, stroke Brake Chamber, Type 0. rod, stroke Brake Chamber, Type 0.6 rod,. stroke Brake Chamber, Type 0 8 rod,. stroke Brake Chamber, Type rod, stroke Brake Chamber, Type 0 0 rod,. stroke Brake Chamber, Type /0. rod, stroke Brake Chamber, Type /0.6 rod,. stroke Brake Chamber, Type /0 8 rod,. stroke Brake Chamber, Type /0 8.6 rod, stroke Brake Chamber, Type /0 0 rod,. stroke Brake Chamber, Type 0/0. rod, stroke Brake Chamber, Type 0/0.6 rod,. stroke Brake Chamber, Type 0/0 8 rod,. stroke Brake Chamber, Type 0/0 8.6 rod, stroke Brake Chamber, Type 0/0 0 rod,. stroke Washer, Hardened /8 Included in item Nut, Lock /8 UNC, B Included in item. SA-00- Jam Nut, Clevis /8 UNF, A Included in item. A-0 Clevis, Slack Adjuster 0 mm Clevis, Slack Adjuster 00 mm *See Note. Included in item. Includes clevis pin and split pin. *See Note. NOTE : When replacing a Type- brake chamber fitted to either an AAT or AANT INTRAAX axle (0 rod and. stroke), use part no (8 rod and. stroke) and extended clevis part no NOTE : All drum brake chambers are supplied complete with new fasteners and 0 mm clevis to suit manual and/or Haldex automatic slack adjusters. Refer to Slack Adjusters on page for further details regarding automatic slack adjusters Rev H

14 SLACK ADJUSTERS Slack Adjuster, Manual, 6 & Slack Adjuster, Manual. & Kit, Auto Slack Adjuster, 6 & Kit, Auto Slack Adjuster. & 6. S-866 Slack Adjuster, Auto. S-868 Slack Adjuster, Auto 6 S-97 Nut, Flanged Haldex Auto Slack Adjuster S-96 Stud Haldex Auto Slack Adjuster Grommet, Stud Haldex Slack Adjuster Includes items, & 6. Includes item Rev H

DISC BRAKES TOOWOOMBA IRON HUB ROTOR The Toowoomba iron hub and rotor assembly is no longer available

Hendrickson has developed a kit to enable the replacement of a damaged or worn rotor.

Rotor service kit part number 988-06 includes the following parts: Item Part Number Description Kit Qty

Sensor bracket Weld On KNORR-BREMSE BRAKE CALLIPER IDENTIFICATION During June 006, Hendrickson

Visually, the two calliper designs can be identified by reviewing the calliper housings.

15 DISC BRAKES TOOWOOMBA IRON HUB ROTOR The Toowoomba iron hub and rotor assembly is no longer available in both 8 and PCD configurations. Hendrickson has developed a kit to enable the replacement of a damaged or worn rotor. NOTE: Complete hub replacement details can be found in Hendrickson technical publication Rotor service kit part number includes the following parts: Item Part Number Description Kit Qty SA-00- M6 X mm Pitch X Metric Hex Head Bolt 0 SA-00-7 Flat Washer 0 D-7 0 mm Rotor Assembly S-77 ABS Sensor bracket Weld On KNORR-BREMSE BRAKE CALLIPER IDENTIFICATION During June 006, Hendrickson introduced a new mono-block calliper design (SN7) to replace the two-piece calliper (SB7). Visually, the two calliper designs can be identified by reviewing the calliper housings. Early Type SB7 Model Brake Calliper Late Type SN7 Model Brake Calliper NOTICE: When servicing Knorr-Bremse SB7 or SN7 Callipers, it is important to order the correct service parts as some components are not interchangeable Rev H

Knorr-Bremse Brake Left & Right Calliper Identification NOTICE: To avoid excessive and tapered brake pad wear, it is

Knorr-Bremse part numbers change over time when design enhancements are made.

This identification label is attached to the calliper body with a silicone adhesive.

A visual check can be made to see if the calliper matches the diagrams below.

16 Knorr-Bremse Brake Left & Right Calliper Identification NOTICE: To avoid excessive and tapered brake pad wear, it is important not to swap the Left and Right brake callipers. Knorr-Bremse part numbers change over time when design enhancements are made. Therefore, the part and type numbers found on the identification label will vary depending on build date. This identification label is attached to the calliper body with a silicone adhesive. There are a number of other ways to identify the correct left or right calliper. A visual check can be made to see if the calliper matches the diagrams below. The numbers cast into the calliper housing can also be referenced. On the inside of the calliper will be the number (Right Hand) or (Left Hand) cast into the body. Refer table below. Knorr-Bremse Identification Right Calliper Left Calliper Hendrickson Number Visual Check Casting Mark Casting Mark Image Rev H 6

ConMet Brake Rotor Identification During July 007, Hendrickson introduced a new offset brake rotor design for all pre-set disc brake

When servicing these rotors, it is important to order the correct service kit, as these rotors are not interchangeable.

988-08 The parallel rotor used prior to July 007 can be identified as follows: Both braking plate thickness are the same Large web spacing

0009970 is cast onto the face of the rotor Kit consists of the following: Rotor, Machined 0 x mm Nut, Hex Flanged /8 x 8 UNF Grade 8 Screw,

Early type part number 0009970 cast into rotor Late Type Offset Brake Rotor Rotor Rebuild Kit Part No.

17 ConMet Brake Rotor Identification During July 007, Hendrickson introduced a new offset brake rotor design for all pre-set disc brake applications to replace the parallel rotor design. Visually the two rotor designs can be identified as shown below. When servicing these rotors, it is important to order the correct service kit, as these rotors are not interchangeable. Late Type Offset Rotor Early Type Parallel Rotor Early Type Parallel Brake Rotor Rotor Rebuild Kit Part No The parallel rotor used prior to July 007 can be identified as follows: Both braking plate thickness are the same Large web spacing between braking plates ConMet part no is cast onto the face of the rotor Kit consists of the following: Rotor, Machined 0 x mm Nut, Hex Flanged /8 x 8 UNF Grade 8 Screw, Phillips Head - #8 - UNF ABS Pulse Ring NOTE: Early type (parallel) and late type (offset) rotors are not interchangeable. Early type part number cast into rotor Late Type Offset Brake Rotor Rotor Rebuild Kit Part No The offset rotor used after July 007 can be identified as follows: Both braking plate thickness are different Small web spacing between braking plates ConMet part no is stamped onto the outer edge of the rotor. Kit consists of the following: Rotor, Stepped 0 x mm Nut, Hex Flanged /8 x 8 UNF Grade 8 Screw, Phillips Head - #8 - UNF ABS Pulse Ring Late type part number 0069 stamped onto edge Rev H

18 DISC BRAKE SYSTEM MAXXT. [SARN 76 FB] S-70- Kit, Dust Shield Disc Brake Includes fastener bolts & washers. B-66 Bush, ABS Sensor Mounting Sensor, ABS Clip, Retaining ABS Sensor SA-00- Bolt, Calliper to Axle M8 x. Class 0 6 SA-900- Washer, Hardened M Rotor Kit, mm Kit includes rotor and items 8 & 9. See also item 0. 8 SA-00- Bolt, Rotor to Hub M6 x, Class Included in items 7 & 0. 9 SA-00-9 Washer, Rotor to Hub /8 0 Included in items 7 & Rotor and Hub Kit, 8 PCD Kit includes bare hub with rotor & fasteners Rotor and Hub Kit, PCD (items 7, 8 & 9). Not illustrated. *See Note. NOTE: Refer to Hendrickson parts bulletin for more details regarding hub spare parts Rev H 8

19 DISC BRAKE CALLIPER MAXXT. [SARN 76 FB] Direction of rotation arrow (Left calliper illustrated) S-97-L Calliper Assembly, LH S-97-R Calliper Assembly, RH Includes fasteners. S-0- Repair Kit - Brake Pad S-0-9 Repair Kit - Pressure Plate Includes LH & RH plate. S-0- Repair Kit - Calliper Guide Pin and Bush D-676- Repair Kit - Calliper Piston Seal Rev H

20 DISC BRAKE SYSTEM WABCO HTD [SARN 7 FB] S Kit, Clamp On Type Dust Shield Disc Brake Suits 7 mm ( ) axle. Includes clamp. NLA Kit, Clamp On Type Dust Shield Disc Brake Suits 6 mm (.7 ) axle. S-6-7 Kit, Dust Shield Disc Brake Bolt on type. Includes bolts & washers. B-66 Bush, ABS Sensor Mounting Suits 6 mm (.7 ) axle Bracket, ABS Sensor Mounting Suits 7 mm ( ) axle & iron hub Bracket, ABS Sensor Mounting Suits 7 mm ( ) axle & aluminium hub Washer, Hardened M Bolt, Calliper to Axle M0 x. x Clip, Retaining ABS Sensor Sensor, ABS 9 D-90 Rotor Assembly, 70 mm Socket Head Bolt M6 x x Rev H 0

21 DISC BRAKE CALLIPER WABCO HTD [SARN 7 FB] Direction of rotation arrow (Left calliper illustrated) Repair Kit, Brake Pad Calliper Assembly, LH Calliper Assembly, RH *See Note. D-676- Repair Kit, Calliper Piston Seal Single calliper kit Repair Kit, Pad Wear Indicator D-676- Repair Kit, Calliper Guide Pin and Bush Single calliper kit. *See Note Kit, Calliper Cap Heavy Duty Includes LH & RH side Kit, Calliper Guide Pin Cover Includes LH & RH side Repair Kit, Pressure Plate Includes LH & RH side. NOTE : Brake calliper assemblies do not include the wear indicators or guide pin covers. NOTE : The calliper guide pin and bush kit (item ) includes standard calliper caps Rev H

22 DISC BRAKE SYSTEM WABCO HTD-0. [SARN 8 FB] S Kit, Dust Shield Clamp On Type. Suits 7 mm ( ) axle. Includes clamp. S Kit, Dust Shield Clamp On Type. Suits 6 mm (.7 ) axle. Includes clamp. S-6-0 Kit, Dust Shield Disc Brake Bolt on type. Includes fastener bolts & washers. B-66 Bush, ABS Sensor Mounting Suits 6 mm (.7 ) axle Bracket, ABS Sensor Mounting Suits 7 mm ( ) axle & iron hub Bracket, ABS Sensor Mounting Suits 7 mm ( ) axle & aluminium hub Clip, Retaining ABS Sensor Sensor, ABS Bolt, Calliper to Axle M0 x. x Washer, Hardened M Kit, KIC ABS Tone Ring. 0 Includes locking pin. For KIC rotors with separate tone ring, from 0 onwards Rotor Rebuild Kit, 0 mm ConMet parallel rotor. *See Note Rotor Rebuild Kit, 0 mm ConMet offset rotor. *See Note. D-7 Rotor Assembly, 0 mm KIC. Includes item. SA-00-9 Washer, Flat /8 0 Suits KIC rotor D-7. NSS Nut, Hub to Rotor 0 Suits ConMet rotor. Use item 0. *See Note. SA-00- Bolt, Hub to Rotor M6 x x 0 Suits KIC rotor D-7. NOTE: For ConMet brake rotor identification, refer to ConMet Brake Rotor Identification on page Rev H

23 DISC BRAKE CALLIPER WABCO HTD-0. [SARN 8 FB] Direction of rotation arrow (left calliper shown) D-676- Repair Kit, Brake Pad D-6-L Calliper Assembly, LH *See Note. D-6-R Calliper Assembly, RH D-676- Repair Kit, Calliper Piston Seal Single calliper Kit. D-676- Repair Kit, Pad Wear Indicator D-676- Repair Kit, Calliper Guide Pin and Bush Single calliper Kit. *See Note Kit, Calliper Cap Heavy Duty Kit, Calliper Guide Pin Cover Includes LH & RH side Repair Kit, Pressure Plate Includes LH & RH side. NOTE : Brake calliper assemblies do not include the wear indicators or calliper guide pin covers. NOTE : The calliper guide pin and bush kit (item ) includes standard calliper caps Rev H

24 DISC BRAKE SYSTEM KNORR-BREMSE. [SARN 98 FB] S Kit, Dust Shield Disc Brake Suits 7 mm ( ) axle. Includes clamp. S Kit, Dust Shield Disc Brake Suits 6 mm (.7 ) axle. Includes clamp. B-66 Bush, ABS Sensor Mounting Suits 6 mm (.7 ) Axle Rotor Rebuild Kit, 0 mm Parallel rotor includes nuts & ABS ring. *See Note Rotor Rebuild Kit, 0 mm Offset rotor includes nuts & ABS ring. *See Note Bracket, ABS Sensor Mounting Suits 7 mm ( ) axle & iron hub Bracket, ABS Sensor Mounting Suits 7 mm ( ) axle & aluminium hub Bolt, Calliper to Axle M0 x. x Washer, Hardened M Clip, Retaining ABS Sensor Sensor, ABS Brake Pad Kit Includes adjuster plug, nut & retainer hardware. NLA Calliper Assembly, LH SB7 Use updated SN7 replacement calliper. 0 NLA Calliper Assembly, RH SB7 Use updated SN7 replacement calliper Calliper Assembly, LH SN Calliper Assembly, RH SN7 NSS Rotor Mounting Nut 0 Use rotor rebuild kit item. NOTE: For ConMet rotor identification or rebuild kit contents, refer to ConMet Brake Rotor Identification on page Rev H

25 DISC BRAKE CALLIPER KNORR-BREMSE. [SARN 98 FB] Calliper Tappet Kit SB Calliper Tappet Kit SN Calliper Adjuster Kit AR Qty 0. Includes cap and nut Calliper Slide Rebuild Kit SB Calliper Slide Rebuild Kit Heavy Duty SN7. *See Note Grease, Synthetic Calliper Slide Not illustrated. Included in item. NOTE: Hendrickson recommends the use of part no (heavy duty calliper slide rebuild kit) for all SN7 calliper slide bush replacements Rev H

26 DISC BRAKE CHAMBERS Brake Chamber Type (6 mm stroke) *See Note Brake Chamber Type 6 (6 mm stroke) *See Note Brake Chamber Type (6 mm stroke) *See Note Brake Chamber Type (7 mm stroke) Brake Chamber Type /6 (6 mm stroke) *See Note Brake Chamber Type / (7 mm stroke) *See Note Brake Chamber, LH Type / (7 mm stroke) Brake Chamber, RH Type / (7 mm stroke) Brake Chamber Type 6/6 (6 mm stroke) *See Note. S-697- Brake Chamber Type 6/ (6 mm stroke) *See Note. *See Note. 90 degree port. Suits HTD Nut, Conelock M6 x. Class 0 Included in item Washer, Hardened M6 Included in item. NOTE: Chambers can be fitted to either right or left configurations Rev H 6

SPECIAL TOOLS 97097-0 Tool Kit Calliper Rebuild, Complete Suits Knorr-Bremse SB7 & SN7.

Suits WABCO MAXXT, HTD-77 & HTD-0. To be use with item. *See Note. Suits WABCO HTD-77 & HTD-0.

NOTE: The Calliper rebuild adaptor tool kits to suit WABCO HTD & MAXXT disc brake Callipers

27 SPECIAL TOOLS Tool Kit Calliper Rebuild, Complete Suits Knorr-Bremse SB7 & SN Tool Kit Calliper Rebuild, Basic Tool Kit Calliper Rebuild, Adaptors *See Note. Suits WABCO MAXXT, HTD-77 & HTD-0. To be use with item. *See Note. Suits WABCO HTD-77 & HTD-0. S-0-6 Tool Kit Calliper Rebuild, Adaptors To be use with item. *See Note. Suits MAXXT. NOTE: The Calliper rebuild adaptor tool kits to suit WABCO HTD & MAXXT disc brake Callipers ( or S-0-6), must be used in conjunction with Calliper rebuild basic tool kit (9896-0) Rev H

28 Revisions Table DATE REV PAGE DESCRIPTION // C, & added as per ECP 087. //6 D 7 S-778- description revised from 6. x 8-/8 to read x 8-/8 /0/6 E, added ECP added ECP 09. Note revised to advise that kit guide pin cover not included in Calliper assembly. /0/6 F,, 6 Bolt on dust shield and fasteners added as per ECP 08. /0/6 F 0 Item revised to NSS and item (Fastener Kit) added. 0/0/6 G 0, Washer SA-00-9 updated to reflect upgraded part ECP /09/7 H, 9 Update to new style ABS sensor bracket number S /09/7 H 6 Delete NLA slack adjusters. 08/09/7 H 7, 8 Added Toowoomba Iron Hub parts numbers & Knorr-Bremse Calliper L/R Identification. 08/09/7 H,, 6 Update number and add image of ABS Sensor Bush for.7 Axle B /09/7 H 9..7 dust shield NLA. Correct reference to HTD /09/7 H Added KIC ABS Tone Ring & dust shield kit part number. Gunite rotor NLA replaced by KIC. 08/09/7 H 6 Update Knorr-Bremse calliper part numbers. 08/09/7 H All New clearer format, rationalised small hardware, added SARN numbers, corrected illustrations and minor adjustments throughout. Need Help? Call or customerservice@hendrickson.com.au HENDRICKSON COMMERCIAL VEHICLE SYSTEMS AUSTRALIA ABN Letcon Drive, P.O. Box 06 Dandenong, Victoria, Fax Rev H Information contained in this literature was accurate at the time of publication. Product changes may have been made after the copyright date that are not reflected. 07 Hendrickson USA, L.L.C. All Rights Reserved Printed in Australia

PARTS LIST INTRAAX AANT230 ZMD TRAILER SUSPENSION SYSTEM. LIT NO: DATE: November 2018 REVISION: B

PARTS LIST INTRAAX AANT230 ZMD TRAILER SUSPENSION SYSTEM. LIT NO: DATE: November 2018 REVISION: B PARTS LIST INTRAAX AANT30 ZMD TRAILER SUSPENSION SYSTEM LIT NO: 97114-117 DATE: November 018 REVISION: B INTRAAX AANT30 ZMD TRAILER SUSPENSION SYSTEMS PARTS LIST TABLE OF CONTENTS INTRODUCTION 3 ABBREVIATIONS