Special Chemicals VDC approved cleaner. General Applicability All Scion iq models, including 10 Year Anniversary Edition.

Size: px
Start display at page:

Download "Special Chemicals VDC approved cleaner. General Applicability All Scion iq models, including 10 Year Anniversary Edition."

Transcription

1 Preparation Part Number: PT or PT (Extension Box w/aha) Kit Contents Item # Quantity Req. Description 1 1 Extension Module w/bt cable 2 1 DA/Ext Harness 3 1 GPS Antenna kit 4 4 Screws (M5x8) Hardware Bag Contents Item # Quantity Req. Description 1 1 GPS Antenna 2 3 Wire clips 3 1 GPS Plate 4 5 Wire ties 5 1 Foam pad w/ Adhesive Additional Items Required For Installation Item # Quantity Reqd. Description 1 1 Clamp bracket P/N: PT Base Audio DA P/N: PT PT (Conversion Harness Kit) 4 1 PT MC (BT Microphone Kit) 5 1 PT (Hardware Kit) Conflicts Recommended Tools Personal & Vehicle Notes Protection Vehicle protection Blankets Special Tools Notes USB Flash Drive Media Must contain MP3 songs Tape cutting template IADS: IQ (optional) Installation Tools Notes Panel Clip Removal Tool e.g. Toyota SST P/N: Socket Wrench Socket 10 mm Socket extension 6 Screwdriver Phillips, #2 Torque Wrench 5.4 N m (48 in lbf) Masking tape Electrical Tape Small round file Ruler Scissors Diagonal cutters Special Chemicals VDC approved cleaner General Applicability All Scion iq models, including 10 Year Anniversary Edition. Recommended Sequence of Application Item # Accessory 1 Premium Audio Upgrade (Extension Box) 2 Base Audio *Mandatory Vehicle Service Parts (may be required for reassembly) Item # Quantity Reqd. Description Legend Notes STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. SAFETY TORQUE: This mark indicates that torque is related to safety. Page 1 of 32 pages

2 Preparation Parts Description of Extension Module Kit (PT or PT ) Item # Parts Name Parts No. Qty 1 Extension Module PT AA or 1 PT AA 2 Harness PT AB 1 3 Screw (M5 x 8) W GPS Antenna PT AA 1 5 Cable Ties 5 6 GPS Plate 1 7 Wire Clip 3 8 Foam Adhesive Pad (25cm x 8cm) 1 Not included in kit but REQUIRED for installation: Receiver Assembly Radio Unit (PT ) 1 2 Item # Parts Name Parts No. Qty 1 Receiver Assembly Radio Unit PT Screw (M5x8) 8 Not included in kit but REQUIRED for installation. Clamp Brackets (PT ) 1 Item # Parts Name Parts No. Qty 1 Clamp Brackets PT Set Page 2 of 32 pages

3 Not included in kit but REQUIRED for installation: Conversion Harness Kit (PT ) Item # Parts Name Parts No. Qty 1 Antenna + 10 pin adapter PT Microphone + 28 pin adapter 1 3 USB adapter 1 Not included in kit but REQUIRED for installation: BT MICROPHONE (PT MC) Item # Parts Name Parts No. Qty 1 Bluetooth microphone PT MC 1 2 Sheet Tape (30 x30) 7 3 Lock Tie (L = 150) 2 4 Protective Tape (30 x30) 1 5 Cable Rail (20mm) 1 Page 3 of 32 pages

4 Not included in kit but REQUIRED for installation: Hardware Kit (PT ) 1 2 Item # Parts Name Qty 1 PVC tape (200mm 100mm) 1 2 Butyl tape (110mm 50mm) 1 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as:- Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). Safety (eye protection, rechecking torque procedure, etc.). Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Scion dealer for a copy of this document. Page 4 of 32 pages

5 Battery Fig mm Socket, Ratchet Negative Battery Cable 1. Vehicle Protection. (a) Protect the fender before starting. (b) Remove the negative battery cable (Fig. 1-1). (1) Do not touch the positive terminal with any tool when removing cable. (c) Check kit contents. 2. Disassembly of Vehicle. NOTE: Place all removed parts on a protected surface. NOTE: When disconnecting wiring connectors do NOT pull on the wiring, pull on the connector only. NOTE: Engage the parking brake while working. Nylon Made Panel Removal Tool Instrument Cluster Finish Panel PPO Disassembly (a) Remove the instrument cluster finish panel (Fig. 2-1). Clips (x3) Clips (x3) (1) Disengage the six (6) clips. (2) Disconnect the connectors and remove the instrument cluster finish panel. Fig. 2-1 Page 5 of 32 pages

6 Clips (x3) Nylon Made Panel Removal Tool Clips (x3) (b) Remove the center No.1 instrument cluster finish panel (Fig. 2-2). (1) Disengage the six (6) clips. (2) Disconnect the connector. Fig. 2-2 Center No.1 Instrument Cluster Finish Panel (3) Twist the harness retainer clip and remove the center No.1 instrument cluster finish panel. Ratchet, Extension, Socket 10mm Radio Mounting brackets (c) Remove the bolts (4), then remove the radio mounting brackets and set aside for reassembly (Fig. 2-3). Fig. 2-3 Bolts (x4) Tape (d) Remove the tape securing the audio harnesses (Fig. 2-4). Harnesses for Radio Fig. 2-4 (e) Position shift lever to N position (Fig. 2-5). Fig. 2-5 Page 6 of 32 pages

7 (f) Remove center console upper panel. (1) Remove panel by disengaging 8 clips (Fig. 2-6). (2) Disconnect any connectors connected to the panel and remove panel. Fig mm socket (g) Remove center console box. (1) Disengage bayonet clips by rotating 90 degrees counter clockwise (Fig 2-7). Clips (2) (2) DO NOT USE POWER TOOL. (3) Remove trim panel by disengaging 2 clips (Fig. 2-7). Bayonet Clips (2) Fig. 2-7 (h) Remove front console box cover by disengaging 4 clips and pulling toward the shifter along the 2 guides (Fig. 2-8). Fig. 2-8 Page 7 of 32 pages

8 (i) Remove the lower center instrument cluster finish panel. Clips (x4) Fig. 2-9 Clips (x4) (1) Disengage the 8 clips and remove the lower center instrument cluster finish panel (Fig. 2-9). (2) Do not disconnect the wire harness or cable. Cover the panel with the blanket to prevent being damaged and set to the side. Clips (x5) Nylon Made Panel Removal Tool Clips (x4) (j) Remove the combination meter cluster panel. (1) Disengage the 7 clips (x7) from the meter cluster panel and remove the combination meter panel (Fig. 2-10). Fig Phillips Screwdriver, Panel Removal Tool Clips (x2) Screw (x2) Fig (k) Remove combination meter assembly. (1) Remove the two screws (x2), disengage the two clips (x2) and remove the combination meter from the vehicle (Fig. 2-11). (2) Disconnect the 2 connectors. Page 8 of 32 pages

9 Scissors 3. Install Protective Sheet (a) Cut the protection sheet into two 100mm by 100mm pieces as shown in the illustration (Fig. 3-1). Fig Scissors (b) Measure and cut out the two dotted sections on each sheet shown in Fig. 3-2 to get the shape as shown in Fig Fig. 3-2 Adhesive side Overlap (c) Remove the tape liner and fold the tape over on the adhesive is only at the two ends (Fig. 3-3). Fig. 3-3 Adhesive ends (d) Cut the butyl tape. (1) Cut 4 pieces of 10mm by 50mm butyl tape, as shown in the illustration (Fig. 3-4). Fig. 3-4 Page 9 of 32 pages

10 Butyl tape attached to protection sheet adhesive ends. (e) Attach two pieces of the butyl tape to the adhesive ends of each protection sheet (Fig. 3-5). (1) Remove the tape liner on one side of the butyl tape before attaching it to each of the adhesive ends. Fig. 3-5 Edges Reinforcement Protection sheet (100 50mm) (f) Clean the surfaces of the attachment areas on the reinforcement with a VDC approved cleaner as shown (Fig. 3-6). (g) Remove the liners on the other side of the butyl tape and attach each protection sheet to the reinforcement edges as shown in the illustration (Fig. 3-6). Fig. 3-6 Butyl tape (10 50mm) Page 10 of 32 pages

11 First rib 4. Install the BT Microphone Kit (PT MC). Second Rib (a) Locate the second rib from the left along the bottom of the meter opening on the back of the combination meter cluster panel (Fig. 4-1). Fig. 4-1 Round file 10mm (b) Using a small round file, create a 3mm deep notch about 10mm to the right of the second rib to provide a cutout for microphone cable (Fig. 4-2). Second Rib Fig. 4-2 Right side opening of driver IP. (c) Route the connector end of the microphone cable through the right side opening of the driver IP (Fig 4-3). Fig. 4-3 Microphone Cable (d) Route the connector end of the harness along the OE harness behind the vent tube toward the opening at the center of the upper IP (Fig. 4-4). (1) Use a wire fishing tool to assist in routing the wire. (2) Make sure the wire does not touch any sharp metal edges. Fig. 4-4 Page 11 of 32 pages

12 Fig. 4-5 Wire tie Sheet tape (e) Continue to route the connector end of the microphone cable along the OE harness to the right side of the center IP opening. (f) Line up the connector end of the microphone to the ends of the audio connectors on the OE harness and secure the microphone cable to the OE harness with one (1) wire tie as shown (Fig. 4-5). Sheet tape (g) Secure the microphone harness to the OE harness behind the IP support bar with one sheet tape as shown (Fig. 4-5). (h) Secure the microphone cable to the OE harness on the left side of the center IP opening as shown (Fig. 4-6). Fig. 4-6 Sheet Tape (x1) Fig. 4-7 (i) Pull back any slack through the right side opening of driver IP and secure the harness to the OE harness with one (1) sheet tape as shown (Fig. 4-7). (1) There should be no slack in the cable between the center IP opening and the right side opening of drive IP. Inner top surface (2) The cable should not be touching any sharp edges between the center IP opening and the right side opening of the driver IP. Fig. 4-8 BT Microphone (j) Clean the inner top surface of the meter panel where the microphone will mount to with an approved cleaner (Fig. 4-8). Page 12 of 32 pages

13 Microphone (k) Install the microphone. (1) Using the cable notch as a guide, position the microphone such that the rear of the microphone lines up to the rear edge of the panel. The cable should line up to the notch. Fig. 4-9 Sheet Tape (x2) (2) Remove the release paper from the microphone and attach the microphone to the inner top surface of the combination meter cluster panel (Fig. 4-9). NOTE: If the room temperature is 10ºC (50ºF) or below, warm up the tape and the attachment part. When the tape and the attachment part are both 20 C or above when attaching, the initial bond strength will be enhanced. Fig (l) Secure the microphone cable to the back of the meter cluster panel with two (2) pieces of sheet tape as shown (Fig. 4-10). Fig (m) Route the remaining length of the cable along the OE harness down to the center lower IP opening (Fig. 4-11). (n) Reinstall the combination meter assembly. (1) Reinstall the two screws. (o) Reinstall the combination meter panel. Fig (1) Pull excess cable slack toward the center lower IP opening when reinstalling the combination meter panel (Fig. 4-12). Page 13 of 32 pages

14 Fig Diagonal cutters Electrical tape Lock Tie (x1) Cable Bundle (p) Pull the remaining slack from the microphone cable down to the center lower IP. Bundle the cable together and secure the bundle to the vehicle wire harness using one lock tie (x1) (Fig. 4-13). (q) Secure the top and bottom of the bundle to the vehicle harness with two pieces of electrical tape (Fig. 4-13). (r) Trim wire tie. 5. Connect the Conversion Wire harness adapters (P/N: PT ) (a) Connect each conversion harness to the vehicle harness and previously installed microphone connector (Fig. 5-1), located in the radio mounting opening. Antenna 10 pin 20 pin USB Microphone Fig. 5-1 Connect these ends to the vehicle NOTE: The vehicle harnesses connect to the connectors on the conversion harness side with the foam around them. Page 14 of 32 pages

15 6. Preparation before installation Scissors, Foam tape (a) Cut foam tape in half. Cut one of the halves into 10 small pieces (2x4cm) and one large piece (2x8cm) as shown (Fig. 6-1). You may not need all pieces for the installation. 24x8cm Fig. 6-1 Page 15 of 32 pages

16 7. GPS Antenna Installation. NOTE: Before attaching the GPS plate or foam tape, clean the mounting surface with VDC approved cleaner. GPS mounting plate with adhesive backing (a) Remove the GPS plate (Fig. 7-1) from the parts bag kit. Remove paper off the back of the GPS plate, to expose the adhesive backing (Fig. 7-2). GPS Plate Fig. 7-2 Remove paper from GPS plate back Fig. 7-1 Fig. 7-3a 0mm 0mm (b) With the adhesive side facing downward, Align the GPS plate with the air conditioning duct rib as shown (Fig. 7-3a) and secure the plate into the mounting position shown (Fig. 7-3). Air conditioning duct Duct Rib GPS plate Fig. 7-3 Adhesive side Page 16 of 32 pages

17 GPS Antenna, wire clip, foam pad (c) Remove the GPS Antenna from the kit bag. Place the GPS antenna on top of the GPS plate. The antenna will magnetically attach to the plate (Fig. 7-4). Wire clip Fig. 7-4 Foam pad GPS Antenna/mounting plate Air conditioning duct NOTE: Before attaching the wire clip and foam pad, clean the mounting surface with VDC approved cleaner. (d) Remove the paper from the back of the wire clip to expose the adhesive backing and mount the clip in the location shown and secure the GPS wire to the wire clip (Fig. 7-4). (e) Remove the paper from a piece of foam pad and secure the GPS wire to the air conditioning duct with the foam pad (Fig. 7-4). Electrical Tape (f) Match the length of the end of the GPS antenna connector to the USB connector and use electrical tape to secure the USB and GPS harness together (Fig. 7-5).. Fig. 7-5 Electrical tape GPS and USB connectors aligned Page 17 of 32 pages

18 Electrical Tape (g) Bundle the excess GPS wire harness and use electrical tape to secure it to the vehicle OE harness (Fig. 7-6). Fig. 7-6 GPS wire bundle with electrical tape OE Harness Page 18 of 32 pages

19 8. Display Audio and Extension Module assembly. Extension Module (a) Lay the Display Audio (DA) radio on a flat surface with the bottom facing upward (Fig. 8-1). (b) Place the extension module on the bottom of the DA radio as shown (Fig. 8-1). Fig. 8-1 DA Radio BT wire harness connector (c) Remove break-away tape from Bluetooth cable harness. Plug the Bluetooth antenna wire harness into the connector on the DA radio (Fig. 8-1). Make sure both ends of the harness are securely seated between the extension module and the DA radio. Clamp brackets (x2). P/N: PT (d) For the next step you will need the clamp brackets. (P/N: PT ). Note the differences between the Right Hand (RH) and Left Hand (LH) bracket shapes (Fig. 8-2). LH RH Left Hand Bracket Right Hand (Fan Side) Bracket Fig. 8-2 Clamp brackets (x2). P/N: PT (e) Fit the LH and RH clamp brackets into the positions shown (Fig. 8-3), to hold the DA radio and extension module together. LH RH Fig. 8-3 Left Hand Bracket Right Hand (Fan Side) Bracket Page 19 of 32 pages

20 RH 2-R Radio Mounting bracket, Screwdriver, (M5x8) Screws (x4) 2-R RH bracket stamping (f) With the Radio fan side facing upward, place the Right Hand (RH) radio mounting bracket, stamped 2-R on top of the clamp bracket ensuring the mounting screw holes are aligned (Fig. 8-4). (g) Fasten the RH mounting bracket to the radio with the screws (x4) (Fig. 8-4). Fig. 8-4 (M5x8) Mounting Screws (x4) Radio Fan NOTE: Make sure the mounting bracket is flat against the clamp bracket before tightening screws. LH 2-L Radio Mounting bracket, Screwdriver, (M5x8) Screws (x4) 2-L LH bracket stamping (h) With the Radio fan side facing downward, place the Left Hand (LH) radio mounting bracket, stamped 2-L on top of the clamp bracket ensuring the mounting screw holes are aligned (Fig. 8-5). (i) Fasten the LH mounting bracket to the radio with the screws (x4) (Fig. 8-5). Fig. 8-5 (M5x8) Mounting Screws (x4) Extension Module/DA radio wire harness NOTE: Make sure the mounting bracket is flat against the clamp bracket before tightening screws. (j) For the next procedure you will need the Extension module/da interface wire harness, which is included in the Extension module kit (Fig. 8-6). Extension Module 32 Pin Fig. 8-6 Connector DA 24 Pin Connector DA 12 Pin Connector Fig. 8-7 Page 20 of 32 pages

21 (k) Connect the wire harness between the extension module and DA radio as shown (Fig. 8-7). NO CONNECTIONS 16 Pin 9. Install the Receiver Assembly Radio Unit (Wire harness connections). (a) Connect the radio antenna cable, 28 Pin, 6 Pin, and 10 pin harness connector cables to the DA radio (Fig. 9-1 and 9-2). GPS Fig. 9-1 USB 10 Pin 6 Pin 28 Pin Radio antenna (b) Connect the USB cable, and GPS antenna cable to the extension module (Fig. 9-1 and 9-2). Do not connect the USB cable to the DA radio. The USB cable must be connected to the extension module. (Fig. 9-1) USB No harness connection should be made to the 16 pin connector. (Fig. 9-1) 28 Pin Radio antenna 6 Pin Fig. 9-2 GPS 10 Pin (c) Confirm all harness connections are completed as shown (Fig. 9-3). Fig. 9-3 Page 21 of 32 pages

22 10. Install the Receiver Assembly Radio Unit (Vehicle mounting). (a) Insert the radio into the dash. Make sure that the connector for the airbag/seatbelt warning indicator is set to the side, so it does not get caught behind the radio (Fig. 10-1). Airbag/Seatbelt indicator connector Fig Ratchet, Extension, Socket 10mm, Bolts (x4) 4 1 (b) In the sequence shown (1 to 4) (Fig. 10-2). Insert each bolt and hand start. (Use bolts removed in Disassembly of vehicle. (c) Fasten the receiver assembly radio unit with 4 bolts, using 10mm socket wrench. 3 2 Fig In Process Function Tests. (a) Temporarily reconnect negative battery cable. (b) If required, install the 30A DCC fuse. (c) Turn ACC ON. Page 22 of 32 pages

23 11. Map Function Test. (a) Press the Map hard key (H/K) (Fig. 11-1). WARNING: If you are presented with the screen in (Fig. 11-2). Proceed to Map trouble shooting on the next page. Fig Press Map H/K Fig BeSpoke Premium Audio is not installed (b) Press the Confirm button on the DA touch screen (Fig. 11-3). NOTE: This screen automatically goes away after 5 seconds if the Confirm button is not pressed and will then take you to the Map Screen (Fig. 11-3). Fig Press Confirm button. (c) Confirm the Map screen is displayed (Fig. 11-4). Proceed to USB Function Test. Fig Map Screen Page 23 of 32 pages

24 Map trouble shooting If you are presented with the screen shown (Fig. 11-5), and the extension module has been properly installed, then perform the following procedure. Fig Fig BeSpoke Premium Audio is not installed Press and Hold Audio H/K 1) While pressing and holding the Audio H/K, (Fig. 11-6) switch ON and OFF the headlights three consecutive times in quick succession. ON>OFF>ON>OFF>ON>OFF 2) The Service Menu screen will appear. (Fig. 11-7). 3) If the Service Menu screen does not appear, repeat steps 1 and 2. Fig Service Menu Screen Press and Hold Setup H/K 4) With the Service Menu screen shown, press and hold the SETUP H/K. (Fig. 11-7). Wait for the radio to restart, then release SETUP H/K. 5) Turn OFF Acc. 6) Turn ON Acc. 7) Go back and repeat Map Function Test, in the In Process Function Tests section. Page 24 of 32 pages

25 12. USB Function Test. USB/AUX Connector (a) Connect the USB flash drive media to the vehicle s USB/AUX connector (Fig. 12-1). Fig (b) Press the Source button on the touch display screen (Fig. 12-2). Fig Source button (c) Select the USB mode button (Fig. 12-3). (d) Confirm song plays (e) Remove flash drive from USB port. Fig USB button Page 25 of 32 pages

26 13. Radio Antenna check. (a) Press the Source button (Fig. 13-1). Fig Source button (b) Press the FM source select button (Fig. 13-2). Fig Press FM Source select button (c) Press the SEEK/TRACK Up H/K button (Fig. 13-3). Confirm that the radio tunes to a FM radio station and sound is heard. Fig Press SEEK/TRACK UP H/K button Page 26 of 32 pages

27 NOTE: To perform the following function tests you will need to enter the DA Service Menu (Fig.14-2). To access the Service Menu, do the following. 1) Turn ACC ON. Fig Press and Hold Audio H/K Service Menu screen 2) Once the DA radio is powered on, press and hold the Audio hard key (Fig. 14-1). 3) While holding the Audio H/K, switch ON and OFF the headlights three consecutive times in quick succession. a. ON>OFF>ON>OFF>ON>OFF 4) The Service Menu screen will appear (Fig. 14-2). 5) If the Service Menu screen does not appear, repeat steps 2 and 3. Fig GPS Antenna and Bluetooth Antenna check. (a) Press the Function Check/Setting button (Fig. 14-3). Fig Press Function Check/Setting button (b) Press the Next Page button (Fig. 14-4). Fig Press Next Page button Page 27 of 32 pages

28 (c) Press the EXT BOX button (Fig. 14-5). Fig Press EXT BOX button Extension Module Service Mode Screen (d) Press the Diagnostics button, on the Extension Module Service Mode screen (Fig. 14-6). Fig Press Diagnostics button (e) Confirm the following connections are displayed (Fig. 14-7). Bluetooth Antenna Connection: YES GPS Antenna Connected: YES Fig Page 28 of 32 pages

29 15. Hands Free Microphone check (a) Press the BACK button (Fig. 15-1). Fig Press BACK button (b) Press the Microphone Level button (Fig.15-2). Fig Press Microphone Level button Fig Microphone Level Indicator (c) While sitting in the driver s seat, speak loud and clearly, preferably looking in direction of microphone location in the vehicle. Say, Check! Check! Test! Test! Watch the Microphone Level Indicator and confirm the level indicator is responding with your voice (Fig. 15-3). Microphone Level Indicator response LOW thru HIGH Page 29 of 32 pages

30 16. Completing the installation (a) Turn OFF vehicle ignition. (b) Reconnect the electrical connector to the instrument cluster and reinstall the instrument cluster with the 2 screws.. (c) Reconnect the electrical connector to the surrounding bezel of the instrument cluster, and clip back into place with 2 clips. Fasten with screw. (d) Reinstall the audio cluster. (e) Verify the panels fit together properly with no uneven gaps between them. Battery Fig mm Socket, Ratchet Negative Battery Cable (f) Clean up and remove any trash. (g) Reconnect the vehicle s negative battery cable (Fig. 16-1). (1) Position the negative cable at the original factory position. (2) Tighten the nut to 5.4 N m. (48 in lbf). Torque: 5.4 N m (48 in lbf) (3) Do not touch the positive terminal with any tool when replacing the cable. (h) Perform functional checks. (i) If required, replace the 30A DCC fuse in its original position. (j) Remove sticker from front of radio (Fig. 16-2). Fig Page 30 of 32 pages

31 Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Function Checks Insert CD audio disc and confirm operation. Turn radio on and confirm operation. Antenna is functional. Fader Balance Illumination Functioning CD player. Radio functions properly. Reception of AM/FM stations. Functioning balance to front and rear speakers. Functioning balance to left and right speakers. Illumination should function properly Vehicle Function Checks Steering Wheel audio controls Passenger seat belt reminder light Hazard switch HVAC (heating ventilation and air conditioning system) Rear window defogger Rheostat Combination meter Electroluminescent panel (if equipped) Battery cable torque Vehicle Appearance Checks Visual Inspection (After accessory installation and removal of protective covers(s)) Functioning audio controls. Proper operation of the passenger seat belt reminder light. Proper operation of the hazard switch. Verify proper operation of of the the air air of air conditioning system. Proper operation of the rear window defogger Functioning dimmer control. Proper operation of combination meter EL panel functions properly. 5.4 N m (48 in lbf) Ensure no damage (including scuffs and scratches) was caused during the installation process. Panels should fit and align properly. (For PPO installations, refer to TMS Accessory Quality Shipping Standard) Page 31 of 32 pages

32

SCION iq AUDIO Preparation

SCION iq AUDIO Preparation Preparation Part Number: PT546-00140 (Base Radio) Kit Contents Item # Quantity Reqd. Description 1 1 Receiver Assembly, Radio Unit 2 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description

More information

SCION tc PREMIUM AUDIO Preparation. Part Number: PT (Extension Module w/ AHA)

SCION tc PREMIUM AUDIO Preparation. Part Number: PT (Extension Module w/ AHA) Preparation Part Number: PT296-12160 Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt (M5x8) 6 5 Wire tie (10 ) Hardware

More information

TOYOTA im NAVIGATION UPGRADE Preparation

TOYOTA im NAVIGATION UPGRADE Preparation Preparation Part Number: PT296-00170 PT296-12170 (Extension Module w/ AHA) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt

More information

SCION im PREMIUM AUDIO Preparation

SCION im PREMIUM AUDIO Preparation SCION im 2016 - PREMIUM AU Preparation Part Number: PT296-12160 (Extension Module w/ AHA) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna

More information

LEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation

LEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20

More information

SCION tc Navigation System Preparation. Part Number: PT

SCION tc Navigation System Preparation. Part Number: PT Preparation Part Number: PT611-21111 Kit Contents Item # Quantity Reqd. Description 1 1 Navigation System 2 1 GPS Antenna 3 1 Bluetooth Antenna 4 1 Wire Harness (Reverse / Park Brake) 5 1 RCA Relay Cable

More information

General Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools

General Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

TOYOTA Matrix XM SATELLITE RADIO Preparation

TOYOTA Matrix XM SATELLITE RADIO Preparation Preparation Part Number: Mounting Kit PT546-12080 Tuner Assembly 86180-0W031 (Music Only) Tuner Assembly PT546-00090 (Music Plus Data) NOTE: Part number of this accessory may not be the same as the part

More information

SCION XB HANDS FREE BLU LOGIC Preparation

SCION XB HANDS FREE BLU LOGIC Preparation SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

TOYOTA im INTERIOR LIGHT KIT Preparation

TOYOTA im INTERIOR LIGHT KIT Preparation Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1

More information

TOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT

TOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,

More information

SCION xb SIRIUS SATELLITE RADIO TUNER Preparation

SCION xb SIRIUS SATELLITE RADIO TUNER Preparation Preparation Part Number: PTS3-52050 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Antenna, Exterior 2 Wire Harness 3 Bracket,

More information

TOYOTA tc HANDS FREE BLU LOGIC Preparation

TOYOTA tc HANDS FREE BLU LOGIC Preparation TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

TOYOTA TACOMA XM SATELLITE RADIO Preparation

TOYOTA TACOMA XM SATELLITE RADIO Preparation Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item

More information

SCION XB HANDS FREE BLU LOGIC Preparation. Item 4 Item 5 Item 6 Item 7. General Applicability. Note: Recommended Tools

SCION XB HANDS FREE BLU LOGIC Preparation. Item 4 Item 5 Item 6 Item 7. General Applicability. Note: Recommended Tools SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00090 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item 1 Item 2 Item

More information

TOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation

TOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation TOYOTA TUNDRA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

TOYOTA VENZA HANDS FREE BLU LOGIC Preparation

TOYOTA VENZA HANDS FREE BLU LOGIC Preparation TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

LEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation

LEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated

More information

TOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)

TOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback) Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting

More information

TOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools

TOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number

More information

TOYOTA TACOMA INTERFACE KIT FOR IPOD Preparation

TOYOTA TACOMA INTERFACE KIT FOR IPOD Preparation Preparation Part Number: PT545-00082 Kit Contents Item # Quantity Reqd. Description 1 1 Unit Assembly Kit 2 1 Mounting Kit 3 1 Hardware Bags 4 1 Unit and Fit Kit List 5 1 Owner s Manual Unit Assembly Kit

More information

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad

More information

TOYOTA PRIUS XM SATELLITE RADIO Preparation

TOYOTA PRIUS XM SATELLITE RADIO Preparation Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity

More information

TOYOTA RAV INTERFACE KIT FOR IPOD Preparation Part Number: PT

TOYOTA RAV INTERFACE KIT FOR IPOD Preparation Part Number: PT Preparation Part Number: PT545-00082 NOTE: Part number of this accessory may not be the same as the part number shown. General Applicability Note: Kit Contents Item # Quantity Reqd. Description 1 1 Unit

More information

Scion xa SATELLITE RADIO TUNER Preparation

Scion xa SATELLITE RADIO TUNER Preparation Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS

More information

SCION XB SUBWOOFER ENCLOSURE Preparation

SCION XB SUBWOOFER ENCLOSURE Preparation Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item

More information

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear

More information

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear

More information

SCION TC HANDS FREE BLU LOGIC Preparation

SCION TC HANDS FREE BLU LOGIC Preparation SCION TC 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00099 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

TOYOTA SIENNA XM SATELLITE RADIO Preparation

TOYOTA SIENNA XM SATELLITE RADIO Preparation Preparation Part Number: Mounting Kit: PT546-08070 Tuner Assy: 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting Kit Contents

More information

Conflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio

Conflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio TOYOTA YARIS SEDAN 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: JBL Audio, Factory Navigation,

More information

TOYOTA TACOMA EC REARVIEW MIRROR Preparation

TOYOTA TACOMA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,

More information

TOYOTA HIGHLANDER TVIP V2 (GBS ADD ON) Preparation

TOYOTA HIGHLANDER TVIP V2 (GBS ADD ON) Preparation Preparation Part Number: 08586-48070 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 ECU Mounting Bracket Hardware Bag Contents Item # Quantity Reqd. Description 1 1 Microphone

More information

TOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation

TOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description

More information

SCION tc ILLUMINATED DOOR SILLS Preparation

SCION tc ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill

More information

SCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT

SCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface

More information

TOYOTA TACOMA TVIP V5

TOYOTA TACOMA TVIP V5 Preparation Part Number: PT398-35090 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor/Microphone 5 2 Warning Labels (English) 6 2 Warning

More information

LEXUS CT 200h ILLUMINATED DOOR SILLS Preparation

LEXUS CT 200h ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left

More information

Part Number: PT

Part Number: PT Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description

More information

SCION xd INTERIOR LIGHTING UPGRADE Preparation

SCION xd INTERIOR LIGHTING UPGRADE Preparation Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,

More information

SCION FR-S FOG LIGHTS

SCION FR-S FOG LIGHTS Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)

More information

SCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation

SCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner

More information

TOYOTA TUNDRA TVIP V5

TOYOTA TUNDRA TVIP V5 Preparation Part Number: PT398-34142 Conflicts Do not install into vehicles with Factory Alarm Systems or SR grade vehicles. Do not use Techstream Lite for Registration. Recommended Sequence of Application

More information

SCION xb AUTO-DIMMING MIRROR Preparation

SCION xb AUTO-DIMMING MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,

More information

SCION xb EC REARVIEW MIRROR Preparation

SCION xb EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,

More information

SCION xa AUTO-DIMMING MIRROR Preparation

SCION xa AUTO-DIMMING MIRROR Preparation Preparation Part Number: PT374-52040 (Compass) PT374-21050 (Homelink) Kit Contents Item # Quantity Reqd. Description 1a 1 AD Mirror Assembly w/compass & Map Lights (P/N PT374-52040) 1b 1 AD Mirror Assembly

More information

TOYOTA COROLLA EC REARVIEW MIRROR Preparation

TOYOTA COROLLA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,

More information

TOYOTA TUNDRA TVIP V4 Preparation

TOYOTA TUNDRA TVIP V4 Preparation Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM

More information

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6

More information

TOYOTA SIENNA TRAILER WIRE HARNESS Preparation

TOYOTA SIENNA TRAILER WIRE HARNESS Preparation Preparation Part Number: PT791-08150 (non-se) PT791-08102 (SE only) Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Module Harness 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting

More information

SCION tc 2014 FOG LIGHT KIT

SCION tc 2014 FOG LIGHT KIT Part #: PT413-21140 Conflicts: P/N PTR11-21100 Lowering Springs (CA only) Kit Contents: Wire Ties Self-Tapping Screws Switch Relay Fog Light Bezel, Left and Right Side Wire Harness Fog Lamp, Left and Right

More information

TOYOTA RAV TRAILER WIRE HARNESS Section I Installation Preparation

TOYOTA RAV TRAILER WIRE HARNESS Section I Installation Preparation Section I Installation Preparation Part Number: 08921-42900 Kit Contents Item # Quantity Reqd. Description 1 1 Converter 2 1 Wire harness 3 1 Sub wire harness No.1 4 2 Plastic Tie (300mm) 5 21 Plastic

More information

TOYOTA RAV FOG LIGHT KIT Preparation

TOYOTA RAV FOG LIGHT KIT Preparation Preparation Part Number: PT413-42163 Kit Contents Item # Quantity Reqd. Description 1 7 7 Wire Tie 2 4 #10-16 Cross Pan-Washer Head Screws 3 1 Switch 4 1 Relay 5 1 LH Fog Light Bezel 6 1 RH Fog Light Bezel

More information

SCION xa LIMITED EDITION SECURITY WITH RKE (V3)

SCION xa LIMITED EDITION SECURITY WITH RKE (V3) Preparation Part Number: 08586-53840 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 V3 Security ECU 3 2 Remote Control Transmitters 4 1 Piezo Buzzer 5 1 Status Monitor 6 1 Radar Sensor

More information

SCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation

SCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner

More information

TOYOTA FJ CRUISER TVIP V5 Preparation

TOYOTA FJ CRUISER TVIP V5 Preparation Preparation Part Number: 08586-36822 Conflicts Do not be installed in vehicles with factory Anti-theft alarm, or Vehicle without Factory Keyless Entry Systems. Recommended Sequence of Application Item

More information

TOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation

TOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation Section I Installation Preparation Part Number: 08586 47840 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 3 1 ECU Mounting Bracket Hardware Bag

More information

TOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation

TOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide

More information

TOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: PT398-34111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts Do not install into vehicles without RKE system. Recommended Sequence of

More information

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:

More information

TOYOTA HIGHLANDER FOG LIGHTS Preparation Part Number: PT , BLACK Part Number: PT , ALUMINIZED

TOYOTA HIGHLANDER FOG LIGHTS Preparation Part Number: PT , BLACK Part Number: PT , ALUMINIZED Preparation Part Number: PT413-42191, BLACK Part Number: PT413-42190, ALUMINIZED Kit Contents Item # Quantity Reqd. Description 1 1 RH Fog Light 2 1 LH Fog Light Hardware Bag Contents Item # Quantity Reqd.

More information

SCION tc LOWERING SPRINGS Preparation

SCION tc LOWERING SPRINGS Preparation Preparation Part Number: PTR11-21100 PTR11-21100-50 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Locking Nut 4 2 Spring Bumper, Front 5 1 Instruction Form Hardware

More information

Scion xb EC Rearview Mirror w/ Shift Light Preparation

Scion xb EC Rearview Mirror w/ Shift Light Preparation 2008 - Preparation Part Number: 00016-79800 Accessory Code: YM10 Kit Contents Item # Quantity Reqd. Description 1 1 Mirror Assembly w/ PRNDL 2 1 Hardware bag 3 1 Installation Manual Hardware Bag Contents

More information

LEXUS RX 450h 2010 TVIP V4 PREPARATION

LEXUS RX 450h 2010 TVIP V4 PREPARATION PREPARATION Part #: PT398-48112 Conflicts: Kit Contents Will not Program with Techstream Lite. RES ECU RES ECU Bracket RES Harness Key Tag Engine Room Label Remote Label Window Label English x2 English

More information

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6

More information

TOYOTA CAMRY TVIP V2 (GBS WITH ADD ON)

TOYOTA CAMRY TVIP V2 (GBS WITH ADD ON) Preparation Part Number: 08586-3T930 Kit Contents Item # Quantity Reqd. Description 1 2 Wire Harness (One wire harness is only for RS3200+) 2 1 GBS ECU 3 1 GBS Mounting Bracket 4 1 Microphone Hardware

More information

SCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray)

SCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray) Preparation Part Number: 08460 21810 (Silver/Dark Gray) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description 1 1 Steering Wheel

More information

TOYOTA RAV TVIP V5

TOYOTA RAV TVIP V5 Preparation Part Number: 08586-42810 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 Security ECU Mounting Bracket 4 1 GBS ECU Mounting Bracket 5 1 Status Monitor 6 1 Security

More information

TOYOTA CAMRY HYBRID TVIP V5 (RS3200 PLUS) Preparation

TOYOTA CAMRY HYBRID TVIP V5 (RS3200 PLUS) Preparation Preparation Part Number: 08586-3T940-AA Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 3 1 ECU Mounting Bracket NOTE: Part number of this accessory may not be the same as the part number

More information

TOYOTA TUNDRA TVIP V5

TOYOTA TUNDRA TVIP V5 Preparation Part Number: 08586-OC890 Conflicts Do not install into vehicles with Factory Alarm Systems or without Immobilizer. Do not use Techstream Lite for Registration. Recommended Sequence of Application

More information

TOYOTA VENZA 2009 TVIP V2 PREPARATION

TOYOTA VENZA 2009 TVIP V2 PREPARATION PREPARATION Part #: PT398-0T092 Conflicts: Kit Contents Do not install into Vehicles without Factory Alarm System. GBS ECU GBS ECU Bracket GBS Harness GBS Microphone Wire Tie Foam Tape M6 Tapping Screw

More information

TOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation

TOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation Preparation Part Number: PT278-35071 Kit Contents Item # Quantity Reqd. Description 1 1 Air Dam / Light Bar Hardware Bag 1 Contents Item # Quantity Reqd. Description 1 2 Screw, M6x33mm, Wafer Head 2 2

More information

TOYOTA TACOMA 2005 TVIP V5 (RS3200 PLUS) Preparation

TOYOTA TACOMA 2005 TVIP V5 (RS3200 PLUS) Preparation Preparation Part Number: 08586 04840 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor 5 2 Warning Labels 6 1 Owner s Manual 7 1 Warranty Card

More information

TOYOTA COROLLA 2010 TVIP V4 PREPARATION

TOYOTA COROLLA 2010 TVIP V4 PREPARATION PREPARATION Part #: PT398-02080 or PT398-02100 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: Do not install into Manual Transmission Vehicles or Vehicles

More information

Please note that these instructions apply to the Toyota Towing Wire Harness. The part you re looking for is PT

Please note that these instructions apply to the Toyota Towing Wire Harness. The part you re looking for is PT This download was hosted by LanderFan.com, your source of tips, tricks, hacks, how-to articles, and other newsy tidbits related to the new (2014+) Toyota Highlander.! Please note that these instructions

More information

LEXUS CT 200h 2011 TVIP V2 PREPARATION

LEXUS CT 200h 2011 TVIP V2 PREPARATION PREPARATION Part #: PT398-76110 Conflicts: Kit Contents GBS ECU V2 Harness GBS ECU Bracket Nut Microphone Foam Tape Wire Tie x1 x1 x1 x1 x1 x2 x15 08190-0C820 08192-6C820 Window Label Owner s Guide PT398-60084

More information

TOYOTA RAV4 w/smart 2009 TVIP V4 PREPARATION

TOYOTA RAV4 w/smart 2009 TVIP V4 PREPARATION PREPARATION Part #: PT398-42110 Conflicts: Do not install into Vehicles manufactured from November 2012 and Onwards. Kit Contents RES ECU Gateway ECU RES ECU Bracket Gateway ECU Bracket Remote Label Key

More information

TOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION

TOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION PREPARATION Part #: PT398-0T110 Conflicts: Will not program with Techstream Lite. Kit Contents RES ECU RES ECU Bracket RES Harness M6 Screw Wire Tie Splicing Connector Remote Label x1 x1 x1 x1 x5 x1 x2

More information

TOYOTA RAV TRAILER WIRE HARNESS Preparation

TOYOTA RAV TRAILER WIRE HARNESS Preparation Preparation Part Number: PU322-42013-UW Kit Contents Item # Qty Description 1 1 Trailer Module Harness 2 1 Trailer 4-Flat Harness 3 1 Trailer Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24

More information

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation Preparation Part Number: PTR07-47100 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Nut 4 1 Instructions Hardware Bag Contents Item # Quantity Reqd. Description 1 2

More information

SCION tc SECURITY (V5) Preparation

SCION tc SECURITY (V5) Preparation Preparation Part Number: PT398-21070 Kit Contents Item # Quantity Reqd. Description 1 1 2 1 GBS ECU Hardware Bag Contents Item # Quantity Reqd. Description 1 1 V5 Security ECU 2 1 ECU Mounting Bracket

More information

TOYOTA HIGHLANDER TRAILER WIRE HARNESS Preparation

TOYOTA HIGHLANDER TRAILER WIRE HARNESS Preparation Preparation Part Number: PT219-48111 Kit Contents Item # Quantity Reqd. Description 1 1 Converter 2 1 Flat 4-pin wire harness 3 5 Plastic tie 4 1 Special plastic tie for stud mount 5 1 Packing 6 2 Bolt

More information

TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation

TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation Part Number: PT297-35061 Kit Contents Item # Quantity Reqd. Description 1 2 Driving Lamp Assembly 2 1 Switch Harness 3 1 Lamp Harness 4 2 Stone Shield

More information

TOYOTA FJ CRUISER SKID PLATE Preparation

TOYOTA FJ CRUISER SKID PLATE Preparation Preparation Part Number: PT1-5071 Kit Contents 1 1 Skid Plate Assembly 1 RH Bracket Assembly 1 LH Bracket Assembly Hardware Bag Contents 1 1 Instruction Sheet 4 M8 Stainless Steel Bolt 4 5 Additional Items

More information

TOYOTA PRIUS CONSOLE APPLIQUES Preparation

TOYOTA PRIUS CONSOLE APPLIQUES Preparation Preparation Part Number: PT948-47160-02 Kit Contents Item # Quantity Reqd. Description 1 1 Console Applique 2 1 Front Face Cover Applique 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 2 3

More information

LEXUS GX TOWING HITCH Preparation

LEXUS GX TOWING HITCH Preparation LEXUS GX460 2014 - TOWING HITCH Preparation Part Number: PT228-60140 Kit Contents Item # Quantity Reqd. Description 1 1 Hitch Assembly 2 1 Wiring Harness Bracket 3 1 Hardware Bag 4 1 Hitch Cover 5 2 Center

More information

TOYOTA SIENNA w/smart Key and Factory Alarm 2015 TVIP V4 PREPARATION

TOYOTA SIENNA w/smart Key and Factory Alarm 2015 TVIP V4 PREPARATION PREPARATION Part #: PT398-08150 Conflicts: Kit Contents Do not install into Vehicles without Smart Key and Factory Alarm. RES ECU RES ECU Bracket V4 Harness Nut Wire Tie Remote Label Key Tag x1 PT398-0T097

More information

TOYOTA TACOMA TVIP V5

TOYOTA TACOMA TVIP V5 Preparation Part Number: PT398-35121 Conflicts Note: Must not be installed in Vehicles with Factory Alarm System and 2013- Vehicles with (4WD Double Cab 6MT and Off-Road Package). Kit Contents Item # Quantity

More information

TOYOTA CAMRY EC REARVIEW MIRROR Preparation

TOYOTA CAMRY EC REARVIEW MIRROR Preparation TOYOTA CAMRY 2010 - EC REARVIEW MIRROR Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ Compass 2 1 Hardware bag Hardware Bag Contents

More information

LEXUS RX 350/450h DOOR EDGE GUARD Preparation

LEXUS RX 350/450h DOOR EDGE GUARD Preparation Preparation Part Number: PT936-48160-XX Kit Contents Item # Quantity Reqd. Description 1 1 Front Driver Door Guard (Reference Pink Sticker) 2 1 Front Passenger Door Guard (Reference Blue Sticker) 3 Rear

More information

SCION FR-S CENTER ARMREST Preparation

SCION FR-S CENTER ARMREST Preparation Preparation Part Number: PT478 18130 Kit Contents Item # Quantity Reqd. Description 1 1 LH Bracket 2 1 RH Bracket 3 1 LH Extrusion 4 1 RH Extrusion 5 1 Slide Assembly 6 4 4.0mm PT (Torx) Screws 7 1 Armrest

More information

LEXUS ES TVIP V2 PREPARATION

LEXUS ES TVIP V2 PREPARATION PREPARATION Part #: PT398-33132 Conflicts: Kit Contents GBS ECU GBS ECU Bracket V2 Harness M6 Bolt Washer Wire Tie GBS Microphone x1 x1 x1 x1 x1 x5 08190-0C820 91651-60618 08192-6C820 x1 Foam Tape V2 Window

More information

LEXUS RX TVIP V2 PREPARATION

LEXUS RX TVIP V2 PREPARATION PREPARATION Part #: PT398-48090 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Vehicles without Factory Alarm System. Kit Contents GBS

More information

TOYOTA COROLLA 2009 TVIP V4 PREPARATION

TOYOTA COROLLA 2009 TVIP V4 PREPARATION PREPARATION Part #: PT398-02080 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.

More information

TOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT

TOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT Preparation Part Number: PT398-48083 Conflicts Do not install into vehicles without RKE systems. Will not program with Techstream Lite. Recommended Sequence of Application Item # Accessory Kit Contents

More information

Preparation Part Number: PT Kit Contents Item # Quantity Reqd. Description 1 1 Rear Spoiler 2 1 Hardware Kit. Hardware Bag Contents

Preparation Part Number: PT Kit Contents Item # Quantity Reqd. Description 1 1 Rear Spoiler 2 1 Hardware Kit. Hardware Bag Contents Preparation Part Number: PT478-11170-09 Kit Contents 1 1 Rear Spoiler 2 1 Hardware Kit Hardware Bag Contents 1 4 M5 Nut 2 4 Clip 3 4 Hole Plug Additional Items Required For Installation 1 1 Outer Drill

More information

TOYOTA COROLLA LOWERING SPRINGS Preparation

TOYOTA COROLLA LOWERING SPRINGS Preparation Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description

More information

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number:

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number: Section I Installation Preparation Part Number: 08586 52960 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Mounting Bracket 3 1 GBS ECU 4 1 Security

More information

TOYOTA Highlander / Highlander HV 2014 TVIP V2 PREPARATION

TOYOTA Highlander / Highlander HV 2014 TVIP V2 PREPARATION PREPARATION Part #: PT398-48141 Conflicts: Do not install into Vehicles without Factory Alarm System. Kit Contents GBS ECU GBS ECU Bracket V2 Harness M6 Nut Bolt Jumper Connector Wire Tie DISCARD x1 08190-0C820

More information