ASSEMBLY INSTRUCTIONS

Size: px
Start display at page:

Download "ASSEMBLY INSTRUCTIONS"

Transcription

1 ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6 BIG BRAKE FRONT HAT KIT PRO STREET APPLICATION,.90 DIAMETER VENTED ROTOR MUSTANG (5 LUG, STOCK OFFSET) PART NUMBER GROUP INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED BY PERSONS EXPERIENCED IN THE INSTALLATION AND PROPER OPERATION OF DISC BRAKE SYSTEMS. IT IS THE RESPONSIBILITY OF THE PERSON INSTALLING ANY BRAKE COMPONENT OR KIT TO DETERMINE THE SUITABILITY OF THE COMPONENT OR KIT FOR THAT PARTICULAR APPLICATION. RACING EQUIPMENT AND BRAKES MUST BE MAINTAINED AND SHOULD BE CHECKED REGULARLY FOR FATIGUE, DAMAGE AND WEAR. DO NOT OPERATE ANY VEHICLE ON UNTESTED BRAKES! BEFORE OPERATING VEHICLE, TEST THE BRAKES UNDER CONTROLLED CONDITIONS IN A SAFE AREA. TEST THE SYSTEM IN STATIC CONDITIONS FOR PROPER PEDAL HEIGHT AND THE ABILITY TO HOLD PRESSURE BEFORE ATTEMPTING TO MOVE THE VEHICLE. MAKE SEVERAL STOPS IN A SAFE AREA AT SLOW SPEEDS AND GRADUALLY WORK UP TO NORMAL OPERATING CONDITIONS. ALWAYS UTILIZE SAFETY RESTRAINT SYSTEMS AND ALL OTHER REQUIRED SAFETY EQUIPMENT WHILE OPERATING THE VEHICLE. IMPORTANT READ THE DISCLAIMER OF WARRANTY INCLUDED IN THE KIT. : Some cleaners may stain or remove the finish on brake system components. Test the cleaner on a hidden portion of the component before general use.

2 Important Notice - Read This First Before any tear-down or disassembly begins, review the following information: Review the wheel clearance diagram (figure, page 3) to verify that there is adequate clearance with the wheels you will be using with the installation. Front brake kits do not include flex lines. OEM brake lines will not adapt to Wilwood calipers. Check the assembly instructions, or associated components section for brake line recommendations before assembly. In addition, Wilwood offers an extensive listing of brake lines and fitting on our web site: Due to OEM production differences and other variations from vehicle to vehicle, the fastener hardware and other components in this kit may not be suitable for a specific application or vehicle. It is the responsibility of the purchaser and installer of this kit to verify suitability / fitment of all components and ensure all fasteners and hardware achieve complete and proper engagement. Improper or inadequate engagement can lead to component failure. Exploded Assembly Diagram INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED BY PERSONS EXPERIENCED IN THE INSTALLATION AND PROPER OPERATION OF DISC BRAKE SYSTEMS. NOTE SPECIFIC PARTS MAY VARY FROM DIAGRAM P PISTON N 7 EXISTING STOCK BOLT (RELOCATED) 3 EXISTING SPINDLE EXISTING HUB ASSEMBLY 6 5 OPTIONAL DRILLED/SLOTTED ROTOR IS SHOWN FOR REFERENCES PURPOSES Figure. Typical Installation Configuration

3 Parts List ITEM NO. PART NO. DESCRIPTION QTY 3 3A / / /0-RS K Bracket, Caliper Mounting Washer,.3 I.D. x.03 O.D. x.033 Thick Rotor, GT-,.5 Thk x.90 Dia, x.75 Bolt Circle, Left and Right Rotor, SRP Drilled and Slotted Hat Washer,.50 I.D. x.500 O.D. x.063 Thick Bolt, /-0 x.00 Long, PT CS Caliper, Billet Superlite 6R Nut, Self-Locking Hex Head Washer,.39 I.D. x.65 O.D. x.057 Thick Stud, 3/-6 x 3/- x.50 long (pre installed in bracket) Washer,.375 I.D. x.75 O.D. x.035 Thick Pad, BP-0 Compound, Axle Set NOTES: Part Number Rotor Bolt Kit, includes part numbers and Part Number Caliper Bracket Mounting Bolt Kit, includes P/N s 30-93, , 0-59, 0-50, & Item 3A is an optional item and is included in the (D) kits. Add -D to end of part number when ordering 6 General Information, Disassembly, and Assembly Instructions Installation of this kit should ONLY be performed by persons experienced in the installation and proper operation of disc brake systems. Before assembling the Wilwood front disc brake kit, double check the following items to ensure a trouble-free installation. INSIDE WHEEL PROFILE (MINIMUM REQUIRED FOR CLEARANCE).3 (3,) RAD.50 (,7) PLACES Make sure this is the correct kit to match the exact make and model year of the vehicles spindle (i.e., hubs for a 90 Mustang spindle will not fit a 997 Mustang spindle). CALIPER.7 HAT THICKNESS 7.36 (6,9) Verify the factory hub stud pattern matches the brake hat in this kit. Verify your wheel clearance using Figure. Inspect the package contents against the parts list to ensure that all components and hardware are included. Disassembly Instructions Disassemble the original equipment front brakes: Raise the front wheels off the ground. Support the front suspension by placing jack stands under the lower control arms. The lower control arms MUST be supported. The vehicle s weight must be on jack stands and not supported by a car jack or hoist. WILWOOD ROTOR CENTER LINE OF WHEEL FACE OF STOCK HUB.3 (,5) WHEEL STUDS Remove the wheel. Remove the two bolts from the backside of the spindle that hold the stock caliper mounting bracket and lift off the bracket and stock caliper as one unit. If space is a problem, you may have to unbolt the stock caliper from the caliper bracket before removal. Save the stock caliper mounting bracket bolts, they will be utilized during reassembly, then slide off the stock hat and rotor assembly. Optional: Removal of the dust face plate to facilitate easy removal of additional parts and/or for aesthetic purposes if you will be running spoked wheel and would like to see the drilled/slotted rotor. FACE OF WILWOOD HAT STOCK WHEEL MOUNTING SURFACE OFFSET Figure. Wheel Clearance Diagram Clean and de-grease the spindles as well as the stock caliper bracket bolts. Remove all nicks or burrs on the spindle snout and threads. Assembly Instructions (numbers in parenthesis refer to the parts list/diagram on the preceding page): CAUTION: All mounting bolts must fully engage insert nuts. Be sure to check that all bolts are either flush, or protruding through flanged side of insert nut after shimming. Apply red Loctite 7 to the stock caliper mounting bracket bolt threads before installation of the caliper mounting bracket (). Install the stock bolts from the near side (opposite from the way they were removed) and place a washer () between the spindle assembly and the caliper mounting bracket (). Torque stock bolts to 65 ft-lb.

4 Assembly Instructions (Continued) With the larger I.D. side of the rotor (3) facing away from the hat (), bolt rotor (3) to hat () through the backside of the rotor using washers (5) and bolts (6). Torque bolts (6) to 5 inlb. Safety wire bolts (6) using standard 0.03 inch diameter stainless steel safety wire as shown in Figure 3. Please refer to Wilwood s data sheet DS-36 (available at for complete safety wire installation instructions. Slide the rotor/hat assembly onto the spindle. Install a couple of lug nuts (hand tighten) to keep the rotor/hat assembly in place while continuing with the installation. NOTE: Please reference the caution statement at the beginning of the assembly instructions. With the bleed screws pointing up, mount the caliper (7) onto the caliper bracket () with the self locking hex nut (), flat washer (9), through the top of the caliper and mounting stud (0) with flat washer () positioned between caliper (7) and caliper mounting bracket (). Finger tighten. View the rotor (3) through the top opening of the caliper (7). The rotor (3) should be aligned in the center of the caliper (7). If not, adjust the caliper (7) by using inch thick shims () placed between the spindle assembly and the caliper mounting bracket (). Finger tighten and recheck alignment. Lubricate caliper mounting studs and nuts with lightweight oil, reinstall the caliper, torque the caliper nuts to ft-lb. BEGIN BY SLIDING THE 0.03" DIAMETER WIRE THROUGH TWO OF THE HOLES (LEFT) THAT ARE 0 APART. TWIST THE WIRE AS SHOWN (BELOW) USING SAFETY WIRE PLIERS. NOW SLIDE ONE WIRE THROUGH TWO OF THE HOLES (0 APART) AND WRAP THE OTHER WIRE AROUND THE BOLT. TWIST THE WIRES TOGETHER TO FORM A PIGTAIL. SEE DS-36 FOR COMPLETE DETAILS. Figure 3. Safety Wire Diagram Remove the bridge bolt from the caliper (7) and install the disc brake pads (). Reinstall the caliper bridge bolt. Remove the two lug nuts that were used to hold the rotor/hat assembly in place during caliper installation. Install the wheel and lug nuts, torque to OEM specifications. Repeat the procedure for the other wheel. NOTE: OEM rubber brake hoses will not adapt to Wilwood calipers and should not be used. The caliper inlet fitting is a /-7 NPT. Use steel adapter fittings at the caliper, either straight, 5 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock. Carefully route lines to prevent contact with moving suspension, brake, or wheel components. Periodically check hose and components for any wear. Wilwood brake and hose kits are designed for use in many different vehicle applications and it is the installer s responsibility to properly route and ensure adequate clearance and retention for brake hose components. Wilwood flex line kit, part number 0-65 is available separably (not included with the kit). Bleed the brake system, referring to additional information on the last page for proper bleeding instructions.

5 Additional Information and Recommendations Please read the following concerning balancing the brake bias on wheel disc vehicles. This Mustang kit can be operated using the stock OEM master cylinder. However, as with most suspension and tire modifications (from OEM specifications), changing the brakes may alter the front to rear brake bias. Rear brakes should not lock up before the front. Brake system evaluation and tests should be performed by persons experienced in the installation and proper operation of brake systems. Evaluation and tests should be performed under controlled conditions. Start by making several stops from low speeds then gradually work up to higher speeds. Always utilize safety restraint systems while operating vehicle. For optimum performance, fill and bleed the new system with Wilwood Hi-Temp 570 grade fluid or EXP 600 Plus. For severe braking or sustained high heat operation, use Wilwood EXP 600 Plus Racing Brake Fluid. Used fluid must be completely flushed from the system to prevent contamination. NOTE: Silicone DOT 5 brake fluid is NOT recommended. To properly bleed the brake system, begin with the caliper farthest from the master cylinder. Bleed the outboard bleed screw first, then the inboard. Repeat the procedure until all calipers in the system are bled, ending with the caliper closest to the master cylinder. NOTE: When using a new master cylinder, it is important to bench bleed the master cylinder first. Test the brake pedal. It should be firm, not spongy and stop at least inch from the floor under heavy load. If the brake pedal is spongy, bleed the system again. If the brake pedal is initially firm, but then sinks to the floor, check the system for fluid leaks. Correct the leaks (if applicable) and then bleed the system again. If the brake pedal goes to the floor and continued bleeding of the system does not correct the problem, a master cylinder with increased capacity (larger bore diameter) may be required. Wilwood offers various lightweight master cylinders with large fluid displacement capacities. NOTE: With the installation of after market disc brakes, the wheel track may change depending on the application. Check your wheel offset before final assembly. If after following the instructions, you still have difficulty in assembling or bleeding your Wilwood disc brakes, consult your local chassis builder, or retailer where the kit was purchased for further assistance. PAD BEDDING PROCEDURE: Pump brakes at low speed to assure proper operation. On the race track, or other safe location, make a series of hard stops until some brake fade is experienced. Allow brakes to cool while driving at moderate speed to avoid use of the brakes. This process will properly burnish the brake pads, offering maximum performance. PART NO Associated Components DESCRIPTION Wilwood Residual Pressure Valve ( lb for disc brakes) Wilwood Residual Pressure Valve (0 lb for drum brakes) Wilwood Proportioning Valve Wilwood Racing Brake Fluid (Hi-Temp 570) ( oz) Wilwood Racing Brake Fluid (EXP 600 Plus) (6.9 oz) Wilwood Floor Mount Brake Pedal (with balance bar) Wilwood Swing Mount Brake Pedal (with balance bar) Wilwood 3/ inch High Volume Aluminum Master Cylinder Wilwood 7/ inch High Volume Aluminum Master Cylinder Wilwood inch High Volume Aluminum Master Cylinder -/6 inch Tandem Master Cylinder (aluminum housing) Mounting Bracket Kit (tandem master cylinder) Wilwood inch Aluminum Tandem Chamber Master Cylinder Wilwood -/ inch Aluminum Tandem Chamber Master Cylinder Pinto Rack and Pinion (new, not rebuilt) Quick Release Steering Hub (3/ inch shaft) Quick Release Steering Hub (5/ inch shaft) Flex Line Kit, 99-up Mustang Bolt Torque Specifications BOLT SIZE /-0 /- 5/6-5/6-3/-6 3/- 7/6-7/6-0 /-3 /-0 9/6-9/6-5/- 5/- TORQUE 5 in-lb 03 in-lb 0 in-lb 9 in-lb ft-lb 30 ft-lb ft-lb 7 ft-lb 65 ft-lb 77 ft-lb 95 ft-lb 05 ft-lb 0 ft-lb 0 ft-lb NOTE: This bolt torque specification list is for use with specific grades of bolts as supplied in the particular Wilwood kit and is not intended as a guide for any other application. Wilwood Disc Brakes 700 Calle Bolero, Camarillo, CA 930 Phone 05 / 3- Fax 05 / 3-93 DS-53D REV DATE:

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR FORGED SUPERLITE BIG BRAKE FRONT HUB KIT WITH 3.00 DIAMETER VENTED ROTOR 968-969 FORD MUSTANG (DISC BRAKE SPINDLE ONLY) PART NUMBER GROUP 0-950 WARNING INSTALLATION OF THIS KIT

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (. OFFSET) 005 - PRESENT MUSTANG 8.8 (5 LUG) PART NUMBER GROUP 0-98 INSTALLATION OF THIS KIT SHOULD ONLY

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 970-973 FORD MUSTANG (DRUM / DISC SPINDLE) PART NUMBER GROUP 0-905 WARNING INSTALLATION OF THIS KIT SHOULD ONLY

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (.36 OFFSET) BIG BEARING FORD PART NUMBER GROUP 0-739 INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.8 OFFSET) BOLT CHEVY PART NUMBER GROUP 0-7 INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED BY PERSONS EXPERIENCED

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP -508-B WARNING INSTALLATION OF THIS KIT SHOULD ONLY

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.8 OFFSET) BOLT CHEVY PART NUMBER 0-7* WARNING INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED BY PERSONS EXPERIENCED

More information

ASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HAT KIT, WITH DIAMETER VENTED ROTOR - RACE

ASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HAT KIT, WITH DIAMETER VENTED ROTOR - RACE www.wilwood.com ASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HAT KIT, WITH 11.75 DIAMETER VENTED ROTOR - RACE 00 - PRESENT BMW MINI COOPER AND MINI COOPER S PART NUMBER GROUP 10-870 DISC BRAKES SHOULD

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.50 OFFSET) BIG BEARING FORD, NEW STYLE PART NUMBER 0-70* WARNING INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED

More information

ASSEMBLY INSTRUCTIONS FOR

ASSEMBLY INSTRUCTIONS FOR ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR AXLE KIT WITH.9 DIAMETER VENTED ROTOR (.36 OFFSET) MOPAR 8-3/ DANA 60 FOR USE WITH GREEN* NON-ADJUSTABLE BEARING PART NUMBER GROUP 0-7-B DISC BRAKES SHOULD

More information

DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND COMPETENT IN THE INSTALLATION AND MAINTENANCE OF DISC BRAKES READ ALL WARNINGS

DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND COMPETENT IN THE INSTALLATION AND MAINTENANCE OF DISC BRAKES READ ALL WARNINGS ASSEMBLY INSTRUCTIONS FOR SUPERLITE BIG BRAKE FRONT HUB KIT WITH 1.90 DIAMETER VENTED ROTOR 197-199 CAMARO, DISC/DRUM SPINDLE 197-197 NOVA, DISC/DRUM SPINDLE 19-19 CHEVY II, DRUM SPINDLE WITH MODIFICATIONS

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER SOLID ROTOR (2.81 OFFSET) OLDS / PONTIAC

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER SOLID ROTOR (2.81 OFFSET) OLDS / PONTIAC ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER SOLID ROTOR (.8 OFFSET) OLDS / PONTIAC PART NUMBER GROUP 0-6703 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.36 OFFSET) BIG BEARING FORD

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.36 OFFSET) BIG BEARING FORD ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH 1.19 DIAMETER VENTED ROTOR (.36 OFFSET) BIG BEARING FORD PART NUMBER GROUP 10-7139 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.75 OFFSET) CAMARO / FIREBIRD

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.75 OFFSET) CAMARO / FIREBIRD ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (.75 OFFSET) 993-997 CAMARO / FIREBIRD PART NUMBER GROUP 0-78 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR EARLY FORD - DRUM SPINDLE

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR EARLY FORD - DRUM SPINDLE ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.00 DIAMETER VENTED ROTOR 93-98 EARLY FORD - DRUM SPINDLE PART NUMBER GROUP -3 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH DIAMETER VENTED ROTOR CAMARO/FIREBIRD (DISC SPINDLE)

ASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH DIAMETER VENTED ROTOR CAMARO/FIREBIRD (DISC SPINDLE) ASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1979-1981 CAMARO/FIREBIRD (DISC SPINDLE) PART NUMBER GROUP -817-B DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH DIAMETER SOLID ROTOR PINTO / MUSTANG II

ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH DIAMETER SOLID ROTOR PINTO / MUSTANG II ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH 0.75 DIAMETER SOLID ROTOR 97-978 PINTO / MUSTANG II (FIVE LUG CONFIGURATION ONLY)* PART NUMBER GROUP 0-03-B DISC BRAKES SHOULD ONLY BE INSTALLED

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.36 OFFSET) MOPAR 8-3/ / DANA 60 FOR USE W/GREEN () NON-ADJUSTABLE BEARINGS W/SNAP RING PART NUMBER 0-7* WARNING

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR FORD MUSTANG (DRUM / DISC SPINDLE)

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR FORD MUSTANG (DRUM / DISC SPINDLE) ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH 1.19 DIAMETER VENTED ROTOR 1965-1969 FORD MUSTANG (DRUM / DISC SPINDLE) PART NUMBER GROUP 140-1107 DISC BRAKES SHOULD ONLY BE INSTALLED

More information

ASSEMBLY INSTRUCTIONS FOR PART NUMBER GROUP

ASSEMBLY INSTRUCTIONS FOR PART NUMBER GROUP ASSEMBLY INSTRUCTIONS FOR DYNAPRO 6 BIG BRAKE FRONT HAT KIT, 1.19 DIAMETER VENTED ROTOR 1990-005 ACURA/CIVIC ( LUG) 000-003 CIVIC SI ( LUG) 007 - PRESENT HONDA FIT FOR FACTORY 6 mm DISC SPINDLE PART NUMBER

More information

ASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT CHEVROLET CORVETTE

ASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT CHEVROLET CORVETTE ASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT 965-98 CHEVROLET CORVETTE PART NUMBER GROUP 40-857 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED

More information

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6R PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR GENERAL MOTORS G BODY DISC SPINDLE

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6R PRO SERIES FRONT HUB KIT WITH DIAMETER VENTED ROTOR GENERAL MOTORS G BODY DISC SPINDLE ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6R PRO SERIES FRONT HUB KIT WITH 1.88 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP 10-198 DISC BRAKES SHOULD ONLY BE INSTALLED

More information

ASSEMBLY INSTRUCTIONS FOR DYNAPRO 6 BIG BRAKE FRONT HUB KIT WITH DIAMETER VENTED ROTOR CAMARO (DISC SPINDLE)

ASSEMBLY INSTRUCTIONS FOR DYNAPRO 6 BIG BRAKE FRONT HUB KIT WITH DIAMETER VENTED ROTOR CAMARO (DISC SPINDLE) www.wilwood.com ASSEMBLY INSTRUCTIONS FOR DYNAPRO 6 BIG BRAKE FRONT HUB KIT WITH 1.19 DIAMETER VENTED ROTOR 1970-1978 CAMARO (DISC SPINDLE) PART NUMBER GROUP 10-10738 DISC BRAKES SHOULD ONLY BE INSTALLED

More information

ASSEMBLY INSTRUCTIONS FOR PRO-MATRIX OE UPGRADE PAD AND ROTOR KIT REAR, WITH DIAMETER VENTED ROTOR CHEVROLET C-4 CORVETTE

ASSEMBLY INSTRUCTIONS FOR PRO-MATRIX OE UPGRADE PAD AND ROTOR KIT REAR, WITH DIAMETER VENTED ROTOR CHEVROLET C-4 CORVETTE ASSEMBLY INSTRUCTIONS FOR PRO-MATRIX OE UPGRADE PAD AND ROTOR KIT REAR, WITH 1.00 DIAMETER VENTED ROTOR 1988-1996 CHEVROLET C-4 CORVETTE PART NUMBER GROUP 140-8314 DISC BRAKES SHOULD ONLY BE INSTALLED

More information

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6 BIG BRAKE FRONT CHALLENGE SERIES BRAKE KIT WITH HUB AND DIAMETER VENTED ROTOR

ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6 BIG BRAKE FRONT CHALLENGE SERIES BRAKE KIT WITH HUB AND DIAMETER VENTED ROTOR ASSEMBLY INSTRUCTIONS FOR SUPERLITE BIG BRAKE FRONT CHALLENGE SERIES BRAKE KIT WITH HUB AND 1.88 DIAMETER VENTED ROTOR 197-199 CAMARO, DISC/DRUM SPINDLE 197-1974 NOVA, DISC/DRUM SPINDLE 194-19 CHEVY II,

More information

ASSEMBLY INSTRUCTIONS FOR DYNAPRO LOW-PROFILE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.

ASSEMBLY INSTRUCTIONS FOR DYNAPRO LOW-PROFILE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2. www.wilwood.com ASSEMBLY INSTRUCTIONS FOR DYNAPRO LOW-PROFILE PRO SERIES REAR PARKING BRAKE KIT WITH 11.00 DIAMETER VENTED ROTOR (.75 OFFSET) 1 BOLT CHEVY PART NUMBER GROUP 140-11398 DISC BRAKES SHOULD

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH DIAMETER SOLID ROTOR CAMARO/FIREBIRD (DISC SPINDLE) PART NUMBER GROUP

ASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH DIAMETER SOLID ROTOR CAMARO/FIREBIRD (DISC SPINDLE) PART NUMBER GROUP ASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH.75 DIAMETER SOLID ROTOR 1979-1981 CAMARO/FIREBIRD (DISC SPINDLE) PART NUMBER GROUP -8175-B DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE

More information

ASSEMBLY INSTRUCTIONS FOR SCION xa, xb SUPERLITE 4 BIG BRAKE FRONT BRAKE KIT WITH DIAMETER VENTED ROTOR* BASE PART NUMBER

ASSEMBLY INSTRUCTIONS FOR SCION xa, xb SUPERLITE 4 BIG BRAKE FRONT BRAKE KIT WITH DIAMETER VENTED ROTOR* BASE PART NUMBER ASSEMBLY INSTRUCTIONS FOR 00-006 SCION xa, xb SUPERLITE BIG BRAKE FRONT BRAKE KIT WITH 1.88 DIAMETER VENTED ROTOR* BASE PART NUMBER 10-8335 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND

More information

PART NUMBER GROUP

PART NUMBER GROUP www.wilwood.com ASSEMBLY INSTRUCTIONS FOR DYNAPRO LOW-PROFILE PRO SERIES REAR PARKING BRAKE KIT WITH FRONT MOUNTED CALIPERS AND 11.00 DIAMETER VENTED ROTOR (.50 OFFSET) BIG BEARING FORD, NEW STYLE PART

More information

ASSEMBLY INSTRUCTIONS FOR REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.66 OFFSET) MUSTANG, PRESENT

ASSEMBLY INSTRUCTIONS FOR REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.66 OFFSET) MUSTANG, PRESENT www.wilwood.com ASSEMBLY INSTRUCTIONS FOR REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH 1.90 DIAMETER VENTED ROTOR (.66 OFFSET) MUSTANG, 005 - PRESENT PART NUMBER GROUP 10-91 DISC BRAKES SHOULD

More information

INSTALLATION INSTRUCTIONS FOR REMOTE MASTER CYLINDER KIT PART NUMBER(S) , , , ,

INSTALLATION INSTRUCTIONS FOR REMOTE MASTER CYLINDER KIT PART NUMBER(S) , , , , INSTALLATION INSTRUCTIONS FOR REMOTE MASTER CYLINDER KIT PART NUMBER(S) 260-3372, 260-3374, 260-3376 260-3378, 260-3380, 260-5920 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND COMPETENT

More information

ASSEMBLY INSTRUCTIONS FOR WILWOOD D154 PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.42 OFFSET) C-10 CHEVY, 5 LUG

ASSEMBLY INSTRUCTIONS FOR WILWOOD D154 PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.42 OFFSET) C-10 CHEVY, 5 LUG ASSEMBLY INSTRUCTIONS FOR WILWOOD D154 PRO SERIES REAR PARKING BRAKE KIT WITH 1.19 METER VENTED ROTOR (.4 OFFSET) 1963-1987 C-10 CHEVY, 5 LUG PART NUMBER GROUP 140-1569 DISC BRAKES SHOULD ONLY BE INSTALLED

More information

ASSEMBLY INSTRUCTIONS FOR CHEVROLET CORVETTE* WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT BASE PART NUMBER

ASSEMBLY INSTRUCTIONS FOR CHEVROLET CORVETTE* WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT BASE PART NUMBER ASSEMBLY INSTRUCTIONS FOR 965-98 CHEVROLET CORVETTE* WILWOOD FRONT D8-6 CALIPER, BRAKE PAD, AND FLEX LINE REPLACEMENT KIT BASE PART NUMBER 40-857 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE REAR AXLE KIT

ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE REAR AXLE KIT ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE REAR AXLE KIT WITH 11.44 METER SOLID ROTOR (.36 OFFSET) MOPAR 8-3/4 DANA 60 FOR USE WITH GREEN (1) NON-ADJUSTABLE BEARINGS PART NUMBER GROUP 140-555-B DISC

More information

ASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D52 CALIPER KIT GM VEHICLES USING D52 CALIPER AND BRAKE PADS WITH 1.

ASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D52 CALIPER KIT GM VEHICLES USING D52 CALIPER AND BRAKE PADS WITH 1. ASSEMBLY INSTRUCTIONS FOR WILWOOD FRONT D5 CALIPER KIT 1968-1996 GM VEHICLES USING D5 CALIPER AND BRAKE PADS WITH 1.8 THICK ROTORS PART NUMBER GROUP 10-1190 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE

More information

ASSEMBLY INSTRUCTIONS FOR

ASSEMBLY INSTRUCTIONS FOR ASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HUB KIT, 1.19 DIAMETER VENTED ROTOR 1967-1969 CAMARO, DISC/DRUM SPINDLE 1967-1974 NOVA, DISC/DRUM SPINDLE 1964-1966 CHEVY II, DRUM SPINDLE WITH MODIFICATIONS

More information

ASSEMBLY INSTRUCTIONS FOR MUSTANG 8.8 (5 LUG)* DYNALITE REAR AXLE KIT WITH DIAMETER VENTED ROTOR (2.50 OFFSET) BASE PART NUMBER B

ASSEMBLY INSTRUCTIONS FOR MUSTANG 8.8 (5 LUG)* DYNALITE REAR AXLE KIT WITH DIAMETER VENTED ROTOR (2.50 OFFSET) BASE PART NUMBER B ASSEMBLY INSTRUCTIONS FOR MUSTANG 8.8 (5 LUG)* DYNALITE REAR AXLE KIT WITH 1.19 METER VENTED ROTOR (.50 OFFSET) BASE PART NUMBER 140-3018-B DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND

More information

ASSEMBLY INSTRUCTIONS FOR C-10 CHEVY, 5 LUG* REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.

ASSEMBLY INSTRUCTIONS FOR C-10 CHEVY, 5 LUG* REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2. ASSEMBLY INSTRUCTIONS FOR C-10 CHEVY, 5 LUG* REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH 1.00 DIAMETER VENTED ROTOR (. OFFSET) BASE PART NUMBER 10-1091 DISC BRAKES SHOULD ONLY BE INSTALLED BY

More information

Wilwood Brake Kit for Total Performance Spindle

Wilwood Brake Kit for Total Performance Spindle INSTRUCTIONS 835-140170 Speedway Motors, Inc. May 2011 Wilwood Brake Kit for Total Performance Spindle Note: NOTE: Disc brakes operate in a harsh environment. To prevent bolts from working loose, every

More information

ASSEMBLY INSTRUCTIONS FOR. SMALL BEARING FORD, 5 x 5.50 BOLT CIRCLE*

ASSEMBLY INSTRUCTIONS FOR. SMALL BEARING FORD, 5 x 5.50 BOLT CIRCLE* ASSEMBLY INSTRUCTIONS FOR SMALL BEARING FORD, 5 x 5.50 CIRCLE* 1966-1973 FORD BRONCO, 700 POUND AXLE, 10 DRUM SPINDLE 1974-1975 FORD BRONCO, 900 POUND AXLE, 10 DRUM SPINDLE DYNAPRO REAR PARKING BRAKE KIT

More information

ASSEMBLY INSTRUCTIONS FOR DYNAPRO LOW-PROFILE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.75 OFFSET) 12 BOLT CHEVY

ASSEMBLY INSTRUCTIONS FOR DYNAPRO LOW-PROFILE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.75 OFFSET) 12 BOLT CHEVY ASSEMBLY INSTRUCTIONS FOR DYNAPRO LOW-PROFILE PRO SERIES REAR PARKING BRAKE KIT WITH 11.00 DIAMETER VENTED ROTOR (.75 OFFSET) 1 CHEVY PART NUMBER GROUP 140-11398 DISC BRAKES SHOULD ONLY BE INSTALLED BY

More information

ASSEMBLY INSTRUCTIONS FOR REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.36 OFFSET) BASE PART NUMBER

ASSEMBLY INSTRUCTIONS FOR REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.36 OFFSET) BASE PART NUMBER ASSEMBLY INSTRUCTIONS FOR MOPAR 8-3/ / DANA 60* FOR USE W/GREEN (1) NON-ADJUSTABLE BEARINGS W/SNAP RING REAR AXLE DISC / DRUM INTERNAL PARKING BRAKE KIT WITH 1.00 METER VENTED ROTOR (.36 OFFSET) BASE PART

More information

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.36 OFFSET) BASE PART NUMBER

ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.36 OFFSET) BASE PART NUMBER ASSEMBLY INSTRUCTIONS FOR MOPAR 8-3/4 DANA 60 FOR USE W/GREEN (1) NON-ADJUSTABLE BEARINGS W/SNAP RING* DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH 1.19 DIAMETER VENTED ROTOR (.36 OFFSET) BASE PART

More information

IRS Racing Brake Kit (MMBAK-15, -16)

IRS Racing Brake Kit (MMBAK-15, -16) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com IRS Racing Brake Kit (MMBAK-15, -16) Floating rotors (MMBAK-16 ONLY) can move

More information

82-92 CAMARO, FIREBIRD/78-87 REGAL, MONTE CARLO, GRAND PRIX/ S-10 RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS

82-92 CAMARO, FIREBIRD/78-87 REGAL, MONTE CARLO, GRAND PRIX/ S-10 RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS 82-92 CAMARO, FIREBIRD/78-87 REGAL, MONTE CARLO, GRAND PRIX/ S-10 RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 82-92 CAMARO/78-87 REGAL YOU WILL NEED TO MODIFY

More information

Rear Disc Brake Kit. CLICK for More Info Online. Vented Disc with Parking Brake and Forged- Aluminum Four-Piston Calipers

Rear Disc Brake Kit. CLICK for More Info Online. Vented Disc with Parking Brake and Forged- Aluminum Four-Piston Calipers CLICK for More Info Online Vented Disc with Parking Brake and Forged- Aluminum Four-Piston Calipers 12.19 Rotor with Forged Dynalite Caliper Billet Aluminum Parking Brake and Caliper Mounting Bracket Assembly

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-3 1965-72 GM A-BODY 10 & 12 BOLT AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time

More information

79-93 MUSTANG RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS. FOR ANY QUESTIONS, PLEASE CALL M-F 8:00a.m.-8:00p.m. EST.

79-93 MUSTANG RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS. FOR ANY QUESTIONS, PLEASE CALL M-F 8:00a.m.-8:00p.m. EST. 79-93 MUSTANG RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 FORD OWNERS ATTENTION! WHEEL OFFSET Due to the design characteristics of the front suspension of a fox

More information

63-82 CORVETTE IMPALA KIT INSTRUCTIONS

63-82 CORVETTE IMPALA KIT INSTRUCTIONS 63-82 CORVETTE 61-69 IMPALA KIT INSTRUCTIONS RACE, STREET, 2 PISTON AND 4 PISTON FRONT KITS ARE ALL COVERED IN THESE INSTRUCTIONAL SHEETS. 1 AEROSPACE COMPONENTS 727.347.9915 Preparing the spindle: You

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W155-5 CHRYSLER 8 3 /4" & 9 3 /4" REAR AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please take the time

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS R1 REAR DRUM TO DISC BRAKE CONVERSION KIT A130-3 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FORCE 10 SPORT R1 REAR DISC CONVERSION KIT A126-50 2005-10 Chevrolet Silverado and GMC Sierra Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FX4 ELITE REAR DISC CONVERSION KITS WITH INTERNAL PARKING BRAKE A110-14, A111-25, A111-29 for FORD 8" & 9" REAR ENDS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION

More information

Installation Instructions

Installation Instructions Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you

More information

Caution: Refer to Adding Fluid to the Brake System Caution in the Preface section.

Caution: Refer to Adding Fluid to the Brake System Caution in the Preface section. Page 1 of 6 2009 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2094891 Rear Disc Brake Pads Replacement Special Tools J 23738-A Hand Vacuum Pump. Removal Procedure Warning:

More information

M-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS

M-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS Please contact the Tech Line for the most current instruction information (800) 367-3788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: This kit allows for the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125-42 GM 10 & 12 Bolt Rear Axles with Staggered or non-staggered Shocks with C-Clips Thank you for choosing STAINLESS STEEL BRAKES CORPORATION

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION REAR KIT SUM-BK1423 1999-2009 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time to read

More information

79-93 MUSTANG 2 PISTON FLOATER FRONT BRAKE KIT INSTRUCTIONS

79-93 MUSTANG 2 PISTON FLOATER FRONT BRAKE KIT INSTRUCTIONS 79-93 MUSTANG 2 PISTON FLOATER FRONT BRAKE KIT INSTRUCTIONS Preparing the Spindle FOR ANY QUESTIONS PLEASE CALL US @(727) 347-9915 M-F 8:00 AM -8:00 PM EST YOU WILL NEED TO MODIFY YOUR SPINDLE. Note: Some

More information

82-92 CAMARO, FIREBIRD RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS

82-92 CAMARO, FIREBIRD RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS M- F 8:00a.m.-8:00p.m. EST. 82-92 CAMARO, FIREBIRD RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS YOU WILL NEED TO MODIFY YOUR SPINDLE. NOTE: You will need to cut the factory caliper mounting ears off

More information

Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section.

Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section. Page 1 of 6 2008 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2065646 Front Disc Brake Pads Replacement Removal Procedure Tools Required J 23738-A Hand Vacuum Pump.

More information

DISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:

DISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed: Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A120-4 & A120-5 1964-1/2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to

More information

INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT

INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-4 FULL FLOATING AXLE OR A130-5 (1 PIECE AXLE) Thank you

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A118 pre-1985 Ford F150 (except 1983-1984 w/super H/D axle) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

Installation Instructions

Installation Instructions Installation Instructions Rear Disc Brake Conversion Kit Item # RC2001, RC2001X Applications: Mopar 8-3/4 & 9-3/4 Rear Axles Thank you for choosing Leed Brakes for your automotive product needs. Before

More information

Installation Instructions

Installation Instructions Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive

More information

05-08 Mustang FOR ANY QUESTIONS, PLEASE CALL ( ) M-TH 8:00A.M. 8:00P.M., FR 8:00A.M.-7:00P.M. EST CLOSED SATURDAYS AND SUNDAYS

05-08 Mustang FOR ANY QUESTIONS, PLEASE CALL ( ) M-TH 8:00A.M. 8:00P.M., FR 8:00A.M.-7:00P.M. EST CLOSED SATURDAYS AND SUNDAYS 05-08 Mustang FOR ANY QUESTIONS, PLEASE CALL US @ (727-347-9915) M-TH 8:00A.M. 8:00P.M., FR 8:00A.M.-7:00P.M. EST CLOSED SATURDAYS AND SUNDAYS YOU WILL NEED TO MODIFY YOUR SPINDLE. NOTE: You will need

More information

INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125

INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125 INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125 1968-81 CAMARO & FIREBIRD 10 & 12 BOLT W/"C" CLIPS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take

More information

MOPAR RACE/STREET FRONT BRAKE KIT INSTRUCTIONS. FOR ANY QUESTIONS, PLEASE CALL M-F 8:00a.m.-8:00p.m. EST.

MOPAR RACE/STREET FRONT BRAKE KIT INSTRUCTIONS. FOR ANY QUESTIONS, PLEASE CALL M-F 8:00a.m.-8:00p.m. EST. MOPAR RACE/STREET FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 You will need some items for best results when installing your Aerospace Brake kit. The following is recommended: At least

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS POWER FRONT DISC CONVERSION KIT A126-7 1963-66 CHEVY C10 PICKUP NON-POWER FRONT DISC CONVERSION KIT A126-8 1963-72 CHEVY C10 PICKUP Thank you for choosing STAINLESS STEEL BRAKES

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128-4 1997-2004 JEEP WRANGLER (TJ) WITH DANA 44 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES for your braking needs. Pleases take the

More information

Rear Brake Rotor Replacement

Rear Brake Rotor Replacement Page 1 of 7 2009 Pontiac G8 G8 Service Manual Suspension Rear Suspension Repair Instructions Document ID: 2094899 Rear Brake Rotor Replacement Removal Procedure Warning: Refer to Safety Glasses Warning

More information

LEXUS IS 250 Front Performance Brake Kit Section I - Installation Preparation

LEXUS IS 250 Front Performance Brake Kit Section I - Installation Preparation LEXUS IS 250 Front 2006- Performance Brake Kit Section I - Installation Preparation Part Number: PTR09-53080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS A112, A112-1 & A112-93 1979-93 FORD MUSTANG with 7.5" & 8.8" AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-2 1955-70 FULL SIZE CHEVROLET Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read

More information

GM FULL SIZE REAR DISC BRAKE KIT

GM FULL SIZE REAR DISC BRAKE KIT GM FULL SIZE REAR DISC BRAKE KIT This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left). If your axle flange measures 3 1/8 from center to center, you need

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KITS A148-9 & A148-15 1949-54 Chevy Trucks Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please take the time to

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FRONT BIG BRAKE CONVERSION KIT A112-5 1987-93 FORD MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS COMP. R AND COMP. S QUICK CHANGE KITS A200, A200-1 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully

More information

SCION tc BIG BRAKE KIT Section I - Installation Preparation

SCION tc BIG BRAKE KIT Section I - Installation Preparation SCION tc 2005- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-21080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake Caliper

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS COMP CALIPER QUICK CHANGE KIT A213 1968-73 MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A130 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128 1990-1995 JEEP WRANGLER (YJ) WITH DANA 35 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A121-1, A121-2, A121-3, A121-4 1967-69 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take

More information

Tools, Equipment and Supplies Needed:

Tools, Equipment and Supplies Needed: 153-162 DISC BRAKE/DUAL MASTER CYLINDER CONVERSION Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarifi cation.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR CONVERSION KIT A111-2 (FORD 8" & 9" SMALL BEARING) & REAR CONVERSION KIT A111-3 (FORD 9 TORINO) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-1 FULL FLOATING AXLE OR A130-2 (1 PIECE AXLE) Thank you for choosing STAINLESS

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A157 1991-2004 Dodge Dakota 2WD 1991-2002 Dodge Dakota 4WD 1998-2002 Dodge Durango Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for

More information

Hot Rod Front Disc Brake Kits

Hot Rod Front Disc Brake Kits 62 Disc Brake Parts and Conversion Kits Hot Rod Front Disc Brake Kits SUPERBELL POWER STOPPER DISC BRAKE KIT Designed for 3000 lb. cars and heavier. Fits 1939-48 Ford passenger car or Chassis Engineering

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A158 1994-97 Dodge Ram 1500 (2WD & 4WD) and REAR DISC BRAKE CONVERSION KIT A158-1 1998-01 Dodge Ram 1500 (2WD & 4WD) Thank you for choosing STAINLESS

More information

55-64 Full Size Chevy

55-64 Full Size Chevy 55-64 Full Size Chevy Installation Instructions Power Disc Conversion 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand tools. The only tools you may not

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KIT A129-2 1959-64 Full Size Chevrolet Car and FRONT DISC BRAKE CONVERSION KITS A129-3 & A129-4 1965-68 Full Size Chevrolet Car Thank you for choosing

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KITS: A132-1, A133, A133-1 A134, A134-1 1968-73 MUSTANG/FORD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please

More information