0.5mm and 1mm Pitch Connectors For FPC/FFC

Transcription

1 rawing for the most current and accurate design information. 0.5mm and mm Pitch onnectors For FP/FF FH Series Flip-lock Features. ase of Use and Space Savings Only one finger or.9n (Newtons) of force is required to lock Hirose s rotational actuator (flip-lock) as compared to using fingers and 39.N to close a FF/FP connector from our competition. The Flip-Lock design also allows customers to place or more connectors side by side as there is no need to waste additional board space for a side latch.. Strengthened Flip-lock ctuator The standard Flip-Lock requires only.0mm height above the board. strengthened lock lever is available which only requires an additional 0.mm. 3. Supports Thin FP (0.mm) Hirose does not require double-sided FP to have any additional strengthening plate or stiffener and can therefore support a thickness of as little as 0.mm +/ Hirose nsures Reliability Hirose s patented half tuning fork contacts maintain the required normal force without relying on the connector housing. With our competitor s conventional products the housing walls support the contact force, which does not provide for long-term reliability. 5. Prevention of Solder ridge xcess solder cavity absorbs excessive solder and avoids solder bridging.. Three different assembly types FH is offered in Top & ottom ontact and Vertical Mount and offered in both a 0.5mm contact pitch as well as a.0mm contact pitch (bottom contact only). Rotating One-touch Mechanism q w e 0.9

2 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Product Specifications Rating urrent rating: 0.5 (Note ) Operating Temperature Range:_0 to +5ç (Note ) Storage Temperature Range:_ to +50ç (Note 3) Voltage rating: 50V Operating Humidity Range:Relative humidity, 90% max. Storage Humidity Range:Relative humidity, 90% max. (Not dewed) (Not dewed) pplicable FP t=0.3±0.05 Gold plated t=0. ± 0.05 for FHF-*S-0.5SH Item Specification onditions. Insulation resistance 500M ohms minimum 0V. Withstanding voltage No flashover or insulation breakdown. 0V / minute 3. ontact resistance 50m ohms maximum m. urability (Insertion/withdrawal) ontact resistance: 50m ohms maximum No damage, cracks, or parts dislocation. 0 cycles No electrical discontinuity of µs or more Frequency: to 55 Hz, single amplitude of 0.5 mm, 5. Vibration ontact resistance: 50m ohms maximum. hours in each of the 3 directions. No damage, cracks, or parts dislocation. cycles. Shock No electrical discontinuity of µs or more cceleration of 9 m/s, ms duration, ontact resistance: 50m ohms maximum. No damage, cracks, or parts dislocation. sine half-wave waveform, 3 cycles in each of the 3 axis. ontact resistance: 50m ohms maximum.. Humidity(Steady state) Insulation resistance: 50M ohms minimum. 9 hours at 0ç and humidity of 90% to 95% No damage, cracks, or parts dislocation. ontact resistance: 50m ohms maximum. Temperature: -0ç / to 35ç / 5ç / to 35ç,. Temperature ycle Insulation resistance: 50M ohms minimum. Time: / to 3 / / to 3(minutes) No damage, cracks, or parts dislocation. 5 cycles No deformation of Reflow: t the recommended temperature profile 9.Resistance to Soldering heat components affecting performance. Manual soldering: 350±ç for 5 seconds Note : When passing the current through all of the contacts,use 0% of the current rating. Note : Includes temperature rise caused by current flow. Note 3: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers nonconducting condition of installed connectors in storage, shipment or during transportation. Note : Information contained in this catalog represents general requirements for this Series. ontact us for the drawings and specifications for a specific part number shown. Material Part Material Finish Remarks Insulator Polyamide, LP(0 pos.) olor : eige ctuator PPS olor : ark brown UL9V-0 ontact Phosphor bronze Gold plated Metal Fittings rass Tin plated Ordering Information FH - () - S SH (**) q w e r t y u i o!0 q Series Name : FH y ontact alignment: Single w Series No. : u ccentric direction: e lank : standard type : Top contact type lank : standard type : ccentric type S : Type with strengthed flip-lock actuator i ontacts Pitch : 0.5mm, mm F : Type with 0.mm FP nd Thickness o ontact type r Standard type : of contacts SH : SMT horizontal mounting type ccentric type : of contacts in 0.5mm housing SV : SMT vertical mounting type t Standard type : lank!0 Plating specification ccentric type : of contacts (5) : Selective gold plated (55) : Gold plated

3 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Series onfiguration Pitch ottom ontact Type Top ontact Type Vertical mounting Type 0.5mm FH- ** S-0.5SH P. of contacts,,,,,,,,,,, 9, 0,,, 5,,,, 3, 33, 3, 35, 3, 0, 5, 50, 53 FP conductive surface FP conductive surface (bottom side) Type with Strengthened Lock Lever FHS- ** S-0.5SH P.5 of contacts, 0, 5, 50, 53 Type with 0.mm FP nd Thickness FHF- ** S-0.5SH P. of contacts,,,,,,,,, 0,,, 5,,,, 3, 3, 3, 0 FH- ** S-0.5SH P. of contacts,,,,, 0,,,,, 9,, 3, 33, 3, 3, 0,, 5, 50 FH- ** S-0.5SV P. of contacts,,,,,,, 0,,,,, 3, 33, 3, 3, 0, 5, 9, 50, 0 FP conductive surface (bottom side) mm Standard FH- ** S-SH P.9 ccentric FH- ** (**) S-SH Standard of contacts 5,,,, 9,,,,,, ccentric of contacts,,,,,, 9, FH- ** S-SV P. of contacts,,,, 0,, 3

4 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF 0.5mm Pitch ottom ontact Type (0.) Mated ross-sectional iagram. (.) FP/FF ontact Surface (.) (3.) (.3) Note 5 Note 5 Note 5 Note 5 Note 5 Note : The coplanarity of each terminal lead within specified dimension is 0. mm Max. Note : Packaged on tape and reel only. heck packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note : fter reflow, the terminal plating may change color, however this does not represent a quality issue. Note 5 : If there is no problem with the connector height, we recommend the type with the strengthened Fliplock actuator (FHS-*S-0.5SH). Standard type connector height: mm onnector height of type with strengthened Flip-lock actuator:. mm Part FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-9S-0.5SH(**) FH-0S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-5S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-3S-0.5SH(**) FH-33S-0.5SH(**) FH-3S-0.5SH(**) FH-35S-0.5SH(**) FH-3S-0.5SH(**) FH-0S-0.5SH(**) FH-5S-0.5SH(**) FH-50S-0.5SH(**) FH-53S-0.5SH(**) L No ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** 5-0--** ** 5-0--** ** 5-0--** ** ** ** ** ** ** of ontacts Note : mbossed tape reel packaging (,000 pieces/reel). Order by number of reels. Note : (**):Specification. Refer to ordering information

5 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF 0.5mm Pitch ottom ontact Type with Strengthened Flip-lock ctuator ( 0.) Mated ross-sectional iagram FP/FF ontact Surface (.) ( 3.) (.3 ). (.) Note : The coplanarity of each terminal lead within specified dimension is 0. mm Max. Note : Packaged on tape and reel only. heck packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note : fter reflow, the terminal plating may change color, however this does not represent a quality issue. Part FHS-S-0.5SH(**) FHS-0S-0.5SH(**) FHS-5S-0.5SH(**) FHS-50S-0.5SH(**) FHS-53S-0.5SH(**) L No ** ** ** ** ** of ontacts Note : mbossed tape reel packaging (,000 pieces/reel). Order by number of reels. Note : Indicates the specification. For details, please refer to the column "composition of product number"

6 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF 0.5mm Pitch ottom ontact Type with 0.mm FP nd Thickness 0.5 ( 0.) pplicable FP end thickness : 0.±0.05 Mated ross-sectional iagram. 0. FP ontact Surface (.) ( 3.) (.5) (. ). 5. Note : The coplanarity of each terminal lead within specified dimension is 0. mm Max. Note : Packaged on tape and reel only. heck packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note : fter reflow, the terminal plating may change color, however this does not represent a quality issue. Part FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-0S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-5S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-S-0.5SH(**) FHF-3S-0.5SH(**) FHF-3S-0.5SH(**) FHF-3S-0.5SH(**) FHF-0S-0.5SH(**) L No ** ** ** ** ** ** ** ** ** ** 5-0--** ** ** 5-0--** ** 5-0--** ** ** ** ** of ontacts Note : mbossed tape reel packaging (,000 pieces/reel). Order by number of reels. Note : Indicates the specification. For details, please refer to the column "composition of product number"

7 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF 0.5mm Pitch Top ontact Type 0.5 (0.) Mated ross-sectional iagram FP/FF ontact Surface (.9) (.5) 5 () (5)..5 (0.5) (3.) Note : The coplanarity of each terminal lead within specified dimension is 0. mm Max. Note : Packaged on tape and reel only. heck packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note : fter reflow, the terminal plating may change color, however this does not represent a quality issue. Note 5 : If there is no problem with the connector height, we recommend the type with the strengthened Fliplock actuator (FHS-*S-0.5SH). Standard type connector height: mm onnector height of type with strengthened Flip-lock actuator:. mm Part FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-0S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-S-0.5SH(**) FH-9S-0.5SH(**) FH-S-0.5SH(**) FH-3S-0.5SH(**) FH-33S-0.5SH(**) FH-3S-0.5SH(**) FH-3S-0.5SH(**) FH-0S-0.5SH(**) FH-S-0.5SH(**) FH-5S-0.5SH(**) FH-50S-0.5SH(**) L No ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** 5-0--** ** ** ** ** of ontacts Note : mbossed tape reel packaging (,000 pieces/reel). Order by number of reels. Note : (**):Specification. Refer to ordering information

8 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF 0.5mm Pitch Vertical mounting Type Mated ross-sectional iagram ( 0. ) ( 0.) FP/FF ontact Surface F (.5) (.5) (.5) (.. ) ) ( 0.5 Note : The coplanarity of each terminal lead within specified dimension is 0. mm Max. Note : Packaged on tape and reel only. heck packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note : fter reflow, the terminal plating may change color, however this does not represent a quality issue. Part L No. of ontacts F FH-S-0.5SV(**) ** FH-S-0.5SV(**) 5-0--** FH-S-0.5SV(**) ** FH-S-0.5SV(**) ** FH-S-0.5SV(**) ** FH-S-0.5SV(**) ** FH-S-0.5SV(**) ** FH-0S-0.5SV(**) ** FH-S-0.5SV(**) ** FH-S-0.5SV(**) ** FH-S-0.5SV(**) 5-0--** FH-S-0.5SV(**) ** FH-3S-0.5SV(**) ** FH-33S-0.5SV(**) ** FH-3S-0.5SV(**) ** FH-3S-0.5SV(**) 5-0--** FH-0S-0.5SV(**) ** FH-5S-0.5SV(**) ** FH-9S-0.5SV(**) ** FH-50S-0.5SV(**) ** FH-0S-0.5SV(**) ** Note : mbossed tape reel packaging (,000 pieces/reel). Order by number of reels. Note : (**):Specification. Refer to ordering information.

9 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF mm Pitch Type ottom ontact Type.3.0 (0.) FP/FF ontact Surface (.) (3.) (.3) (.) 0. Mated ross-sectional iagram.. 5. Note : The coplanarity of each terminal lead within specified dimension is 0. mm Max. Note : Packaged on tape and reel only. heck packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note : fter reflow, the terminal plating may change color, however this does not represent a quality issue. Standard type ccentric type Part FH-5S-SH(**) FH-S-SH(**) FH-S-SH(**) FH-S-SH(**) FH-9S-SH(**) FH-S-SH(**) FH-S-SH(**) FH-S-SH(**) FH-S-SH(**) FH-S-SH(**) FH-S-SH(**) FH-()S-SH(**) FH-()S-SH(**) FH-()S-SH(**) FH-()S-SH(**) FH-()S-SH(**) FH-()S-SH(**) FH-0(9)S-SH(**) FH-50()S-SH(**) L No. of ontacts ** ** ** ** ** ** 5-0--** ** ** ** ** ** ** ** ** ** ** ** ** Note : mbossed tape reel packaging (,000 pieces/reel). Order by number of reels. Note : The mm version of FH is constructed by loading every other contact into the 0.5mm housing. When a housing designed for an odd number of 0.5mm pitch contacts is used; the spacing from the edge to the first contact on either side is the same as the distance between each contact,.0mm. Hirose considers this design to be a standard-type.0mm connector. n eccentric-type connector using a housing designed for an even number of 0.5mm pitch contacts and consequently one side has mm distance from the edge to the first contact. (See FP/FF dimensional drawing on page 9) The part number for the eccentric type describes the size of the 0.5mm housing used and lists the number of.0mm pitch contacts in parentheses () as shown in the above table

10 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF mm Pitch Vertical Mounting Type Mated ross-sectional iagram (0.) (0.) FP/FF ontact Surface F (.5) (.5) (.) (.) (.5) (Metal fitting dimension) Note : The coplanarity of each terminal lead within specified dimension is 0. mm Max. Note : Packaged on tape and reel only. heck packaging specification. Note 3 : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Note : fter reflow, the terminal plating may change color, however this does not represent a quality issue. Part L No. of ontacts F FH-S-SV(**) ** FH-S-SV(**) ** FH-S-SV(**) **.9.. FH-S-SV(**) ** FH-0S-SV(**) ** FH-S-SV(**) ** FH-S-SV(**) ** Note : mbossed tape reel packaging (,000 pieces/reel). Order by number of reels. Note : (**):Specification. Refer to ordering information.

11 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Recommended FP/FF dimensions and Land/Metal Mask dimensions 0.5mm Pitch Product FP/FF dimensions Land / Metal Mask dimensions 0.5mm Pitch ottom ontact Type 0.5mm Pitch Top ontact Type 3.5MIN 0.5±0. of ontacts ±0.05 ±0.05 ±0.0 of ontacts ±0.03(FP) 0.3±0.03(FF) 0.5±0. Product Type Types other than 0.3±0.05min those below Stiffener thickness should be 0. mm (.5 mil) min FHF 0.± MIN Unit: mm ±0. ±0..3±0. of ontacts ± ±0. ±0. ± of ontacts ±0.03(Land) 0.5±0.03(Metal mask) Recommended metal mask thickness : 0.mm Unit: mm ven contact number Odd contact number MIN 0.5±0. 0.5± ±0.03(FP) 0.3±0.05 ±0.05 ± ±0.03(FF) 0.5±0. 3MIN.±0..±0. ±0. 0.±0.(Land) 0.5±0.05(Metal mask) ±0. No. contact ±0..5±0..±0..±0. ±0. 0.±0.(Land) 0.5±0.05(Metal mask) No. contact 0.5±0.05 ± ±0.(Land) 0.5± ±0.05(Metal mask) ± ±0.(Land) 0.5±0.05(Metal mask) ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0. ±0..5±0. 0.5mm Pitch Vertical Mounting Type *Set the stiffener thickness to 0. (.5mil) min. of ontacts 0 of ontacts Unit: mm of ontacts 0 Recommended metal mask thickness : 0.mm of ontacts Unit: mm

12 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Recommended FP/FF dimensions and Land/Metal Mask dimensions mm Pitch Product FP/FF dimensions Land / Metal Mask dimensions πset the stiffener thickness to 0. (.5mil) min. Recommended metal mask thickness : 0.mm mm Pitch ottom ontact Type Standard Type of ontacts ccentric Type of ontacts Unit: mm Standard Type of ontacts ccentric Type of ontacts Unit: mm mm Pitch Vertical Mounting Type *Set the stiffener thickness to 0. (.5mil) min. of ontacts Unit: mm Recommended metal mask thickness : : 0.mm of ontacts Unit: mm

13 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Packaging Specification mbossed arrier Tape s Horizontal Type (ommon to ottom/top ontact, 0.5mm/mm Pitch) (.0) Flat surface for placement with utomatic equipment Reel s (ommon to ll Types) (ø) ( : INSI) nd portion Mounting portion Lead portion (00mm min.) ( ) ( ) ( : OUTSI) lank portion ( pockets min.) mbossed carrier tape lank portion ( pockets min.) Top cover tape 0.5mm Pitch ottom/top ontact Type of ontacts 9 0 mm Pitch ottom ontact Type Standard Type of ontacts of ontacts Note:,000 pieces per reel. of ontacts 3 9 Note:,000 pieces per reel. ccentric Type

14 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Vertical Mounting Type (ommon to 0.5mm/mm Pitch) (.5) Flat surface for placement with utomatic equipment 0.5mm Pitch Vertical mounting Type of ontacts.. of ontacts Note:,000 pieces per reel mm Pitch Vertical mounting Type of ontacts Note:,000 pieces per reel. 0.

15 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF FH Series FP/FF onstruction (Recommended Specifications). FF FF : Flexible Flat able Material Name Material Thickness (µm) Polyester film dhesive (Nickel under plated / Gold plated), soft copper film dhesive Thermoplastic polyester Polyester type () () 35 Polyester dhesive Polyester type Stiffener Polyester type (Note) Total 95 *Real tolerance of thickness dimension is on the order of ±0 µm (5 to 3 µm) Note: Use of a thicker FF results in a stiffer lock action and the lock is more easily released. factor that contributes to thicker FF is the use of 50 µm stiffener which is thicker than the standard ( µm) product. This results in a total thickness of 35 µm. When using FF, control of FF thickness becomes easy if you indicate to us the thickness of the stiffener.. FP FP : Flexible Printed ircuit Material Name overing layer film over adhesive Material Polyimide mil Thickness (µm) (5) (5) Nickel under plated to 5µm / Surface treatmenta 3 Gold plated 0.µm opper foil ase adhesive ase film Reinforcement material adhesive Stiffener u oz 35 Heat-hardened adhesive Polyimide mil Heat-hardened adhesive Polyimide mil Total Precautions. This specification is a recommendation for the construction of the FH Series FP and FF (t=0.3 ±0.05).. For details about the construction, please contact the FP/FF manufacturers.

16 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Recommended Temperature Profile Temperature (ç) Start 5ç (0 seconds) 90 to 0 seconds seconds 0 0ç Preheating Time 0 00ç Soldering MX 50ç ç HRS test conditions Solder method :Reflow, IR/hot air nvironment: :Room air Solder composition :Paste, 9.5%Sn/3%g/0.5%u (Senju Metal Industry, o., Ltd. s Part : M05-M5-3-.5) Test board :Glass epoxy 0mm 0mm.mm thick Land dimensions :Top and bottom contact type 0.3mm.3mm Vertical mounting type 0.mm mm Metal mask :Top and bottom contact type 0.5mm.3mm 0.mm thick Vertical mounting type 0.5mm mm 0.mm thick This temperature profile is based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/thickness and board size/thickness. onsult your solder paste and equipment manufacturer for specific recommendations.

17 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF onnector Operating Instructions, precautions and recommendations ottom ontact Type (common for 0.5mm/mm Pitch) Operation. FP/FF Termination procedure. onnector installed on the board. ) Lift up the actuator. Use thumb or index finger. Precautions ) void grasping the actuator with two fingers or lifting the actuator with fingernail. ) o not use a thin tool such as the tip of a screwdriver to release the lock lever. oing so will cause deformation of the contacts. 3) o not apply force in the direction of arrows,, or while the lock lever is open. oing so will cause the lock lever to become disen gaged, or will damage the hook portion of the connector body. ) Fully insert the FP/FF parallel to mounting surface, with the exposed conductive traces facing down. ) When inserting the FP/FF, do not forcefully rub against the surface beneath the connector insertion slot. oing so will result in the FP/FF forcefully striking the contacts and this will cause contact deformation, peeling of the FP/FF conductors, and other irregularities. FP/FF conductive traces 5) Insert the FP/FF at the proper position of the connector insertion slot, and insert perpendicularly with respect to the connector. Improper insertion will cause continuity problems, disengagement of the lock lever, and damage to the hook portion.

18 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF ottom ontact Type (common for 0.5mm/mm Pitch) Operation 3) Rotate down the actuator until firmly closed. It is critical that the inserted FP/FF is not moved and remains fully inserted. Should the FP/FF be moved, open the actuator and repeat the process, starting with Step. Precautions ) Partial insertion of the FP/FF, offset insertion, and diagonal insertion will result in an unfavorable engagement of the lock lever in which the lock lever is raised. To correct this, first remove the FP/FF and then reinsert it. Forcing the lock will damage the connector. Stiffener ) When locking, handle the FP/FF so that a load is not applied to the FP/FF as would occur by pulling the FP/FF, or lifting it, etc. When a load is applied in the opposite direction to the rotational movement of the lock, an excessive load will be applied and this will cause connector damage.. FP/FF Removal ) Lift up the actuator. ) arefully remove the FP/FF. ) t the time of lock operation, application of force such as that indicated by the arrows in the diagrams below will cause the lock lever to disengage. When the lock lever has become disengaged, please exchange the entire connector.

19 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Top ontact Type Operation. FP/FF Termination procedure. onnector installed on the board. ) Lift up the actuator. Use thumb or index finger. Precautions ) void further lifting of the lock lever once the lock has been released. oing so will cause the lock lever to separate from the rotational shaft, and the lock lever will become disengaged or the hook portion of the connector body will be damaged. Lock lever Rotational shaft ) Fully insert the FP/FF parallel to mounting surface, with the exposed conductive traces facing UP. FP insertion area FP/FF conductive traces ) void further pressing of the lock portion from the locked condition when the FP/FF has not yet been inserted. oing so will cause the lock lever to become disengaged from the rotational shaft, and the hook portion of the connector body will be damaged. Stiffener 3) Rotate down the actuator until firmly closed. It is critical that the inserted FP/FF is not moved and remains fully inserted. Should the FP/FF be moved, open the actuator and repeat the process, starting with Step above. 3) o not insert the FP/FF diagonally. oing so will result in the corners of the FP/FF catching on the contacts and will cause deformation of the contacts.. FP/FF Removal ) Lift up the actuator. ) arefully remove the FP/FF. ) When closing down the actuator apply equal pressure to both sides of the actuator. 9

20 rawing for the most current and accurate design information. FH Series 0.5mm and mm Pitch onnectors For FP/FF Vertical Mounting Type (common for 0.5mm/mm Pitch) Operation. FP/FF Termination procedure. onnector installed on the board. ) Verify that the actuator is positioned upright. If the actuator has rotated to the side, carefully rotate it upright. ctuator upright Precautions ) void forcing the actuator up or down without the FP/FF inserted. ) Insert the FP/FF vertically in the connector slot assuring that the conductive traces of the FP/FF are facing away from the actuator. Stiffener FP/FF conductive traces ) o not insert the FP/FF diagonally. oing so will result in the corners of the FP/FF catching on the contacts and will cause deformation of the contacts. Slot 3) Press down the actuator in the direction shown.. FP/FF Removal Rotate the actuator upward and withdraw the FP/FF. 5-3,OSKI 5-HOM,SHINGW-KU,TOKYO -5,JPN PHON: , FX: The contents of this catalog are current as of date of 09/0. ontents are subject to change without notice for the purpose of improvements.