SC SERIES STUMP CUTTER

Transcription

1 SC SERIES STUMP CUTTER Operating and Maintenance Manual

2 TABLE OF CONTENTS 1. PRODUCT WARRANTY CHECKLIST Dealer s File Copy... 4 Customer s File Copy INTRODUCTION 6 4. SPECIFICATIONS SAFETY Mandatory Safety Shutdown Procedure OPERATION Forward Attaching to and Detaching From a Skidsteer Loader The Controls Preparing to Cut a Stump DAILY MAINTENANCE Tooth Adjustment and Replacement PARTS Tooth Pattern Tooth Pattern. 17 SC & Parts List SC Parts Omni & Omni Parts List Stump Cutter Hydraulic & Parts List HOST KITS.. 30 Revised 07/18/07 1

3 2

4 1. PRODUCT WARRANTY 3

5 2. CHECKLIST DEALER S FILE COPY 2.1 PRE-DELIVERY After the Stump cutter has been completely setup and attached to the host machine, inspect the following. Check off each item after the prescribed action is taken. Check that: No parts of the unit have been damaged in shipment. Check for things such as dents and loose or missing parts; correct or replace components as required. All bolts and fasteners are in place and tightly secured. All grease fittings have been properly lubricated; see lubrication information in this manual. All decals are in place and securely attached. The serial number of your unit is recorded in the space provided on this page. Then, test run the unit while checking that all components are operating correctly. I acknowledge that the procedures were performed on this unit as outlined above DEALERSHIP NAME - DEALER REPRESENTATIVE S NAME 2.2 DELIVERY The following checklist is an important reminder of the valuable information that MUST be passed on to the Customer at the time the unit is delivered. Check off each item as you explain it to the Customer. Give the customer his operators manual. Instruct him to be sure to read and completely understand its contents BEFORE operating the unit. Explain and review with him the SAFETY information in this manual. Explain that regular cleaning and lubrication are required for proper operation and long life. Review with him the lubrication information in this manual. Explain and review with him the service & maintenance information in this manual. Completely fill out the owner s registration, including the customer s signature and return it to the manufacturer. I acknowledge that the above points were reviewed with me at the time of delivery. CUSTOMER S SIGNATURE DATE DELIVERED DATE CHECKLIST FILLED OUT 4

6 2. CHECKLIST CUSTOMER S FILE COPY 2.1 PRE-DELIVERY After the Stump Cutter has been completely setup and attached to the host machine, inspect the following. Check off each item after the prescribed action is taken. Check that: No parts of the unit have been damaged in shipment. Check for things such as dents and loose or missing parts; correct or replace components as required. All bolts and fasteners are in place and tightly secured. All grease fittings have been properly lubricated; see lubrication information in this manual. All decals are in place and securely attached. The serial number of your unit is recorded in the space provided on this page. Then, test run the unit while checking that all components are operating correctly. I acknowledge that the procedures were performed on this unit as outlined above DEALERSHIP NAME - DEALER REPRESENTATIVE S NAME 2.2 DELIVERY The following checklist is an important reminder of the valuable information that MUST be passed on to the Customer at the time the unit is delivered. Check off each item as you explain it to the Customer. Give the customer his operators manual. Instruct him to be sure to read and completely understand its contents BEFORE operating the unit. Explain and review with him the SAFETY information in this manual. Explain that regular cleaning and lubrication are required for proper operation and long life. Review with him the lubrication information in this manual. Explain and review with him the service & maintenance information in this manual. Completely fill out the owner s registration, including the customer s signature and return it to the manufacturer. I acknowledge that the above points were reviewed with me at the time of delivery. CUSTOMER S SIGNATURE DATE DELIVERED DATE CHECKLIST FILLED OUT SERIAL NUMBER 5

7 3. I N T R O D U C T I O N The SC SERIES STUMP CUTTER was designed as an attachment machine for use on skid steer loaders. The information contained in this manual refers only to the Stump Cutting Machine. Information regarding the valves used to control oil flow to the Stump Cutter attachment can be found in the host machine s manual or in the hi flo installation manual if the host machine is so equipped. The information contained within is provided to assist you in preparing, adjusting, maintaining and servicing your machine. More importantly, this manual provides an operating plan for safe and proper use of your machine. Major points of safe operation are detailed in the safety chapter of this manual. Refer to the table of contents for an outline of this manual. Modern machinery has become more sophisticated and, with that in mind, you must read and understand the contents of the manual COMPLETELY and become familiar with your new machine before attempting to operate it. Terms such as right and left as used in the manual, are as though the reader is sitting in the host machine s operator seat and facing the stump cutter. Throughout this manual, information is provided which is set in bold type and introduced by the word NOTE: Be sure to read carefully and comply with the message or directive given. Following this information will improve your operating or maintenance efficiency, help you to avoid costly breakdowns or unnecessary damage, and extend the life of your machine. The Manufacturer and Society of Automotive Engineers have adopted this SAFETY ALERT SYMBOL to pinpoint characteristics that, if not properly followed, can create a safety hazard. When you see this symbol in this manual or on the unit itself, you are reminded to BE ALERT! YOUR SAFETY IS INVOLVED! The manufacturer reserves the right to make changes or improvements in the design or construction of any part without the obligation to install such changes on any unit previously delivered. 6

8 4. S P E C I F I C A T I O N S MODEL SC19 SC21 AP Minimum Hydraulic HP INCHES (300mm) Swing Width. 67 (90 ) 67 (90 ) Cut Below Ground /2 8 1/2 Cut Above Ground Number Of Teeth Weight. 700 lbs 796 lbs 5. SAFETY BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. The Manufacturer always takes the operator and their safety into consideration when designing machinery. Guards are provided on exposed moving parts for the operator s protection, however, some areas cannot be guarded or shielded in order to assure proper operation. In addition, the operator s manual and decals on the machine itself warn you of further danger and should be read and observed closely. The SAFETY ALERT SYMBOL above means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! It stresses an attitude of HEADS UP for safety and can be found throughout this operator s manual and on the unit itself. REMEMBER: The careful operator is the best operator. Most accidents are caused by human error. Certain precautions must be observed to prevent the possibility of injury or damage. 7

9 Please read the rules listed below for safe operation BEFORE you operate this equipment. Use of words CAUTION, WARNING, or DANGER, herein and on the machine itself, signal three degrees of hazard. CAUTION is used for general reminders of good safety practices or to direct attention to unsafe practices. WARNING is used to denote a specific potential hazard. DANGER is used to denote the most serious specific potential hazard. 5.1 MANDATORY SAFETY SHUTDOWN PROCEDURE Work of any type on machinery is always more dangerous when the machine is operating. BEFORE cleaning, lubricating, or servicing this unit, the following MANDATORY SAFETY SHUTDOWN PROCEDURE should ALWAYS be followed: 1 Move host machine s propulsion control to the neutral position and idle engine down. 2. Shut off oil flow to Stump Cutter. 3. Position Stump Cutter so that it is completely resting on the ground or floor. 4. Engage the host machine s hand brake. 5. Move the host machine s throttle to the slow idle position, shut the Engine off and remove the Ignition Key. 6. Relieve hydraulic pressure by moving the Hi-flow and cylinder control levers in both directions 8

10 REMEMBER ALWAYS IDLE ENGINE DOWN BEFORE SHUTTING OFF OIL FLOW. ONLY when you have taken these precautions can you be sure it is safe to proceed. Failure to follow the above procedures could lead to death or serious bodily injury! Some diagrams used herein may show Door(s), Guard(s), or Shield(s) open or removed for illustration purposes ONLY! BE SURE that all Door(s), Guard(s), and Shield(s) are in their proper position(s) and securely attached BEFORE operating the Stump Cutter! Read and observe ALL Safety information and Decals on the host machine and Stump Cutter BEFORE operating the unit! In addition, familiarize yourself with ALL of the Safety Devices and periodically check that they are functioning properly! Refer to the SAFETY chapter of the host machine s operator manual and observe ALL Safety recommendations set forth in that manual! CAREFULLY inspect ALL hydraulic hoses and connections on a routine basis; NEVER use your hand, escaping fluid under pressure can cause serious injury! BE SURE to exercise the MANDATORY SAFETY SHUT DOWN PROCEDURE BEFORE proceeding to do any work on the Stump Cutter! BE SURE the Stump Cutter is properly placed on the ground with the cutting head off the ground, BEFORE attempting to work on the cutting wheel. BEFORE transporting the Stump Cutter, BE SURE to raise the unit completely clear of the ground and turn it off. ALWAYS wear proper clothing and covering when working with or on the Stump Cutter. ALWAYS wear safety glasses or face shield while operating the Stump Cutter. 9

11 DO NOT attempt to work on the Stump Cutter or host machine with the hydraulics live! BE SURE to relieve the hydraulic pressure, by shutting down the engine and moving all control levers to relieve hydraulic pressure BEFORE attempting to disconnect any hoses or BEFORE proceeding to remove the Stump Cutter from the host machine. DO NOT use the Stump Cutter to push objects, it can be damaged by contact with solid objects, as well as upset the stability of the host machine! DO NOT hit the teeth with a steel hammer as this could cause steel chips to fly, causing injury to the eyes or face. REMEMBER! It is the owner s responsibility for communicating information on the safe use and proper operation and maintenance of this machine! 6. O P E R A T I O N 6.1 FOREWORD The Stump Cutter must be attached to a host machine equipped to provide the necessary hydraulics and operational controls. As there are many different host machines available, this manual will only deal with the generic operation of the Stump Cutter. Anyone attempting to attach and operate the Stump Cutter must first have the knowledge and skill of operating the host machine s controls. Information regarding the host machine s controls and attaching procedure is found in the host machine s Operators Manual or from its Authorized Dealer. 10

12 6.2 ATTACHING TO AND DETACHING FROM A SKIDSTEER LOADER During shipment the swingaway control arm is folded down to reduce shipping height. Before connecting the attachment to your skidsteer loader, remove the loose 1/4 capscrew from the lower pivot and the 1/4 clevis pin from the upper pivot and raise the arms. Replace the 1/4 capscrew and self locking nut into the forward most hole of the lower pivot plate. Tighten bolt to remove any looseness but to allow full travel. After connecting the attachment to the skidsteer loader check that the swingaway arm is located correctly left to right. The lower pivot bracket has extra bolt holes to allow moving. Adjust the upper and lower 1/4 clevis pins into the correct holes to achieve the best location of the hydraulic controls. WARNING! BE SURE THE BOOM ARMS ARE ALL THE WAY DOWN AND THE BUCKET DUMP ROLLED ALL THE WAY BACK, WHEN ADJUSTING THE ARMS, TO AVOID ACCIDENTAL CONTACT WITH THE OPERATOR OR SKID STEER CONTROLS!! Drive the skidsteer up to the quick attach of the Stump Cutter and connect up. Exercise the MANDATORY SAFETY SHUTDOWN PROCEDURE before proceeding. After installing hydraulic quick couplers compatible with your skidsteer to the two 3/4 main hoses, connect them to the hydraulic outlets assuring that the hose connected to the P port of the valve goes to the pressure outlet of the skidsteer. Detaching is a reversal of this process. 11

13 6.3 THE CONTROLS After all mechanical and hydraulic connections have been made and the swingaway arm is adjusted properly, raise the cutter wheel off the ground. Make sure all persons and objects are clear of the wheel area. Turn on the skid steer Hi-Flo and/or auxiliary flow, increase engine RPM to approximately 1/2. Once the cutter wheel is turning you will be able to operate the controls. Push the left hand lever down, this should raise the cutter head. Pushing it up will lower the cutter head, operate the cylinder through is full stroke several times to purge any air from this circuit. Pushing the right hand lever down will swing the cutter head to the left, pushing it up will swing the cutter head to the right. Operate the swing cylinder through its full stroke to purge any air from the circuit. 6.4 PREPARING TO CUT A STUMP Drive up to the stump with the cutting head swung all the way to the right. Try to approach the stump from a position that will allow the skidsteer to sit as level as possible left to right. This will allow the cutter head to swing horizontally. Position the cutter head just to the right of the stump. With the back plate approximately vertical lower the loader boom arms unit the stump cutter roller is on the ground. Turn on the Hi-Flo and or the auxiliary flow to the stump cutter. Increase engine to full RPM, make sure the wheel is not contacting the ground. Adjust the cutter head to cut approximately 1 to 1 1/2 inches of stump, swing the head to the left across the top near edge of the stump, lower the head another 1 to 1 1/2 inches and swing the head back to the right. Continue in this manner. If the cutter wheel stalls reduce the depth of cut. As the radial surface of the cut becomes long, move the skidsteer slightly to allow cutting a new area, see sketch. Start new cut here or here 12

14 Do not move forward into the stump while making a cross sweep. Doing so could result in vibration and motor overload that could cause machine and tooth damage. When cutting surface roots make shallow cuts as large chunks can be broken off and thrown if the cut is too deep. Do not try to make a deep plunge cut unless you have teeth that cross over the wheel. Without them the wheel will rub and grab. 7. DAILY MAINTENANCE CAUTION: NEVER attempt to do any maintenance to the Stump Cutter while it is running. Exercise the MANDATORY SAFETY SHUTDOWN PROCEDURE BEFORE proceeding. NOTE: Careful attention to the daily maintenance routines will go a long way toward ensuring efficient operation. 1. At the start of each day, lubricate the grease fittings at each side of the cutter wheel and top and bottom bearings of pivot shaft. Standard shop gun grease will suffice. 2. Using the correct size wrenches, retighten any loose hardware. 3. Inspect for any loose hydraulic fittings of damaged hoses; retighten or replace as required. 4. Clean away any dirt or chips from the wheel and bearings. 5. Check for dull, broken, bent or loose teeth, replace or tighten as required. WARNING: NEVER use your hands to check for hydraulic Leaks. Escaping fluid under pressure can cause serious injury! If injured by escaping fluid, see a doctor at once. If proper Medical treatment is NOT administered IMMEDIATELY Serious infection or reaction can develop! 13

15 7.1 TOOTH ADJUSTMENT AND REPLACEMENT It is important that the teeth are gauged properly. The correct measurement is 1 1/8 to 1 3/16 from the tip of the tooth to the edge of pocket, parallel to the wheel edge. Improper or uneven gauging can cause extra stress and wear on teeth that are extended out too far or excessive wear to pockets and wheel if gauged to short. It is important to monitor the condition of the wheel while adjusting or replacing teeth. Wire brush or clean the wheel so that it can be inspected closely. Make sure the wheel is not cracked. NEVER use a wheel that shows any sign of cracking!! Look at the bolt holes to see if they are worn oversize or are elongated. If they are, the tooth pockets will rotate during use changing the rake or cutting angle of the tooth causing it to hit the wood flat and not cutting it. The pounding that results causes poor cutting performance, tooth bending or breakage and driveline damage. Also look for damage where the tooth clamps to the wheel. Make sure that when the teeth and pockets are bolted to the wheel, that only the tooth and no part of the pocket touches the wheel. If the pocket touches the wheel there may not be enough clamp force to keep the tooth in place and it could fly out! If any to these conditions occur the wheel must be rebuilt or replaced. The condition of the teeth have a big impact on how fast and how smooth the stump cutter cuts. Teeth that are dull or bent will not cut as well as sharp teeth. Any bent or broken teeth should be replaced. Proper sharpening requires restoring a sharp edge and the proper clearance angle to the shank and carbide tip. To accomplish this a regular grinding wheel must be used to restore the proper clearance angle on the shank. Then use a Green-Silicon Carbide Wheel to grind the carbide at the same angle until it has a sharp edge. Using the green wheel on the shank or the regular stone on the carbide is unproductive and will damage the wheels. Always use the right stone for the material it was intended to grind. SEE PAGE 15 FOR SHARPENING DETAILS. 14

16 The bolts that clamp the pocket-tooth combination should be torqued to 150 to 190 foot pounds. DO NOT OVERTORQUE the bolts, this causes wheel damage and makes it difficult to take the pockets off, start at the lower end of the torque range. If the pockets don t loosen, then stay at that point. If they do loosen increase the tightening torque to the point where they stay tight. On a new machine or after replacing or adjusting teeth, run the cutter for about 15 minutes on a small to medium stump, then re-torque the bolts. If your wheel is worn or uneven in the tooth area, the retorquing becomes even more important. The careful use of anti-seize on the bolt threads will make disassembly easier. 15

17 16 TOOTH PATTERN NO LEFT SIDE RIGHT SIDE 1 LT ST 2 LT RT 3 LT RT 4 LT RT 5 ST RT 6 LT RT 7 LT RT 8 LT RT 16

18 32 TOOTH PATTERN NO. LEFT SIDE RIGHT SIDE 1 LT ST 2 LT RT 3 LT RT 4 LT RT 5 LT RT 6 LT RT 7 LT RT 8 LT RT 9 ST RT 10 LT RT 11 LT RT 12 LT RT 13 LT RT 14 LT RT 15 LT RT 16 LT RT 17

19 18

20 SC 19 & 21 STUMP CUTTER PARTS LIST ITEM # PART # DESCRIPTION QTY Back Plate Assembly Stump Cutter Head Assembly Stump Cutter Pivot Shaft Upper Bearing Mount Roller Roller Shaft Hydraulic Cylinder Rod End Pin Lift Cylinder Base End Pin Lift Cylinder Head Lift Pivot Pin Pivot Shaft Bearing C-08* 1/2 Nylok Nut C-16 SAE 1" Flat Washer A-0640 Cotter Pin A-0640 Cotter Pin A-0812 * 1/2x1 1/2 HHCS A-0516 * 5/16"x2" Hex Head Cap Screw C-05* 5/16" SAE Flat Washer C-05* 5/16" Nylon Lock Nut SC Cutter Wheel QD Bushing /16" Threaded Pockets (SC 19) Threaded Pockets (SC 21) Counterbored Pockets (SC 19) Counterbored Pockets (SC 21) D-1016* Teeth Bolts (SC 19) D-1020* Teeth Bolts (SC 21) Straight Teeth (SC 19) Straight Teeth (SC 21) RH Teeth (SC 19) RH Teeth (SC 21) LH Teeth (SC 19) LH Teeth (SC 21) Bearing 1 15/ Wheel Shaft /16" A /8"x1 1/2" Hex Head Cap Screw - Motor Motor Adapter 1 40 See Spec Motor Seal Kit M51 Motor Seal Kit M76 Motor A0512* 5/16"x1 1/2" Hex Head Cap Screw A-05* Lock Washer C-10 5/8" Nylok Nut A-1016* 5/8"x2 Hex Head Cap Screw-offside A1014* 5/8"x1 3/4" Hex Head Cap Screw-Motorside A-10* 5/8" Lock Washer (SC 21) 4 * NOT SHOWN * Hose Clamp Bracket /4" Hose Clamps /4" Clamp Plate /4" Hose Clamp /4" Clamp Plate Knob 1. 19

21 20

22 Stump Cutter Parts List Omni S/N 9029, 9606, 9082, 9094, 9099, & UP ITEM P/N DESC QTY ITEM P/N DESC QTY Plate Back Assy Pocket Thrd Head Assy Pocket Thrd Pivot Shaft Pocket CB Mount Bearing Pocket CB Roller D-1016 Teeth Bolt SC Shaft Roller D-1020 Teeth Bolt SC Hyd Cyl Tooth Str SC Pin Lift Cyl Rod End Tooth Str SC Pin Lift Cyl Base End Tooth RH SC Pin Head Lift Pivot Tooth RH SC Bearing Pivot Shaft Tooth LH SC C-08 Nut Nylok 1/ Tooth LH SC C-16 Washer Flat SAE 1" Bearing Cup&Cone Small A-0640 Pin Cotter Bearing Cup&Cone Large Wheel Assy SC Seal Protector A-0812 HHCS 1/2-13x1 1/2" Hub (Part of Wheel A-0518 HHSC 5/16-18x2 1/4" Nut Flanged C-05 Washer Flat SAE 5/16" 4 40 Motor See Spec C-05 Nut Nylok 5/ Kit Seal M51 Motor AR Spindle & Hub Assy Kit Seal M76 Motor AR Shaft 1 NOT SHOWN Seal 1 20/ O'Ring Motor to Spindle Lock Nut Bearing Bracket Hose Clamp Washer Lock Clamp Hose 1/4" E-04 Plug Pipe Plate Clamp 1/4" 2 28 Housing Spindle Clamp Hose 3/4" Plate Clamp 3/4" 1 21

23 22

24 STUMP CUTTER HYDRAULIC PARTS ITEM # PART # DESCRIPTION QTY Valve Complete Sun Seal Kit for Valve AR Valve Block Only Valve Priority.3 GPM Valve Check PB Valve Check Valve 2 Spool BLB Spool Seal BLB Cylinder Depth/Swing 2 7 Motor - See Motor Spec Motor Shaft Bearing M E-1212 Adapter Str JICM/SAEM E-0404 Adapter Str JICM/SAEM H-08 Plug SAE E-0406 Adapter Str JICM/SAEM B-0406 Adapter 90 Deg JICM/SAEM R-0404 Adapter 90 Deg JICM/NPTM B-1212 Adapter 90 Deg JICM/SAEM G-0604 Adapter Str JICM/NPTM (SC21) B-1212 Adapter 90 Deg JICFS/JICM Orifice Adapter H-0404 Plug SAE Hose 1/4"x51" PB Hose 1/4"x61" Rod Swing Cylinder Hose 1/4"x81" Base Depth Cylinder Hose 1/4"x98" Rod Depth Cylinder Hose 1/4"x48" Base Swing Cylinder Hose 3/4"x95" Valve to Motor Hose 3/4"x101" Valve to Motor Lever Valve Cover BLB Valve Bracket Sun Valve 1 30 SEE HOST KITS Seal Kit Hydraulic Cylinder AR Pivot Box BLB Valve AR * Kit Seal M51 Motor AR * Kit Seal M76 Motor AR * Not Shown 23

25 24

26 56984 SC UNIVERSAL 3 LINE HYD KIT PARTS ITEM P/N DESCRIPTION QTY Directional Valve 2 Function Incs, 2,3,4,5, 6,40& Way Cartridge Only Coil & Connector PO Check Valve Blocking Valve Cartridge Only Relief Valve Cartridge Only Sun Valve Assy Incs,Items 8 thru Valve Block Only Check Valve PB Check Valve Anticav & Return Priority Valve 1 12 Motor See Motor Spec Swing Cyl Depth Cyl E-1212 Adap Str JICM/SAEM B-1212 Adap 90 Deg JICM x SAEM Hose 3/4x101" G0604 Adap Str JICM/BSPPM B-0606 Adap 90* JICM/SAEM B-0404 Adap 90* JICM/SAEM R-0404 Adap 90* JICM/NPTM Hose 3/4x95" Tube PB Tube Valve Pressure Tube Valve Return 1 27 Hose 1/4x Swing Cyl Rod 1 28 Hose 1/4x Swing Cyl Base 1 31 Hose 1/4x Depth Cyl Base 1 32 Hose 1/4x Depth Cyl Rod 1 33 See Host Kit Seal Kit Hyd Cyl AR Seal Kit M51 Motor AR Seal Kit M76 Motor AR Motor Shaft Bearing AR Seal Kit Valve AR Seal Kit Valve AR Valve Bracket Valve Cover Cavity Plug 3 Way Cavity Plug 4 Way 1 25

27 26

28 55350D CABLE CASE 400 SERIES NEW HOLLAND JOHN DEERE PRE 300 SERIES SOCKET COLOR FUNCTION PLANER STUMP CUTTER C Red Slide LT Swing LT D Yellow Slide RT Swing RT H Brown Depth Up Depth Up G Green Depth Dn Depth Dn E White Tilt LT NA F Blue Tilt RT NA Gray Power Beyond B Black Ground CABLE JOHN DEERE 300 SERIES SOCKET COLOR FUNCTION PLANER STUMP CUTTER C Red Slide LT. Swing LT. G Green Slide RT Swing RT F Blue Depth Up Depth Up H Brown Depth Dn Depth Dn D Yellow Tilt LT NA E White NA Gray Power Beyond A Black Ground 27

29 SWINGAWAY ARM ASSEMBLY ITEM # PART # DESCRIPTION QTY Valve Cover BLB Spool Valve Sliding Arm Horizontal arm Knob Vertical Arm Lower Bracket A /8 x 3 HHCS C-06 3/8 Nyloc Nuts A /4 x 2 3/4 HHCS C-04 1/4 Nyloc Nuts C /4 x 3 Clevis Pin Lever (BLB Type) AR Lever (Cable Type) AR Pivot Box (BLB Type) AR Pivot Box (Cable Type) AR ** SWINGAWAY KIT ALL ITEMS ABOVE 28

30 29

31 STUMP CUTTER HOST KITS NEW HOLLAND-JOHN DEERE-CAT-KOMATSU-BOBCAT CASE 400- CASE BIC SHF- SC21 HOST KIT Part # Description Qty Cost Total Cost /4 x 72 Hose /8 x 180 Case Drain Hose 1 111E-1212 Adapter 2 111E-0608 Case Drain QC Adapter CASE CASE XT - GEHL - JCB - MUSTANG SC21 HOST KIT Part # Description Qty Cost Total Cost /4 x 100 Hose /8 x 180 Case Drain Hose 1 111E-1212 Adapter 2 111E-0608 Case Drain QC Adapter LF NEW HOLLAND - JOHN DEERE - CAT - BOBCAT CASE SC19 HOST KIT Part # Description Qty Cost Total Cost /4 x 72 Hose 2 111E-1212 Adapter LF JCB - KOMATSU - CASE BIC SHF SC 19 Part # Description Qty Cost Total Cost /4 x 100 Hose 2 111E-1212 Adapter 2 30

32 P/N S. Hoover Wichita, KS