OPERATING INSTRUCTIONS 5630 Valve control INTERBUSLOOP version for double seat valves with board version V 2.0 or V 3.0

Size: px
Start display at page:

Download "OPERATING INSTRUCTIONS 5630 Valve control INTERBUSLOOP version for double seat valves with board version V 2.0 or V 3.0"

Transcription

1 Valve control versions IBU board for Part Nr. double seat valves V. Contr. DSV/NT IBU 2STS THSA KAPG9 1MV V. Contr. DSV/OT IBU 2STS THSA KAPG9 2MV Personnel operating and maintaining the valve control are asked to read and observe these operating instructions and to use it in compliance with the specified technical data. The manufacturer does not assume liability for any damages arising from improper or not as directed use. All relevant regulations concerning accident prevention and safety of electric equipment have to be observed while operating, servicing, or repairing the valve control. V. Contr. DSV/UT IBU 2STS THSA KAPG9 2MV V. Contr. DSV/OUT IBU 2STS THSA KAPG9 3MV V. Contr DSV/NT IBU 2STS THSA KAQS 1MV V. Contr. DSV/OT IBU 2STS THSA KAQS 2MV V. Contr. DSV/UT IBU 2STS THSA KAQS 2MV V. Contr. DSV/OUT IBU 2STS THSA KAQS 3MV V. Contr DSV/NT IBU 2STS EHOS KAPG9 1MV V. Contr. DSV/OT IBU 2STS EHOS KAPG9 2MV V. Contr. DSV/UT IBU 2STS EHOS KAPG9 2MV V. Contr. DSV/OUT IBU 2STS EHOS KAPG9 3MV V. Contr DSV/NT IBU 2STS EHOS KAQS 1MV V. Contr. DSV/OT IBU 2STS EHOS KAQS 2MV V. Contr. DSV/UT IBU 2STS EHOS KAQS 2MV V. Contr. DSV/OUT IBU 2STS EHOS KAQS 3MV IDENTIFICATION CODE V-CONTROL DSV/NT IBU 2STS THSA KAPG9 1 MV DSV/OT EHOS KAQS 2MV DSV/UT 3 MV DSV/OUT Product = valve control DSV/NT = double seat v. not clockable DSV/OT = double seat v. above clockable DSV/UT = double seat v. below clockable DSV/OUT = double seat v. above and below clockable Control board INTERBUS 2 position detectors transparent cap mechanical / LED position indication special steel cap without position indication KAPG9 cable connection PG9 cable connection Quickon plug Number of 3/2 way solenoid valves 1 2 PURPOSE-CONFORMANT USE The valve controls are used to control pneumatically actuated lifting valves in production lines of the beverage and foodstuff industry, in pharmaceutics, bio-engineering, and in the chemical industry. They encompass the complete actuation, sensing, and electronics required for their connection and integration into advanced, powerful control systems. DESCRIPTION OF THE VALVE CONTROL The valve control has a modular design. Depending on the type, the pneumatic (max. of 3 3/2 way solenoid valves) and electric control modules with 2 proximity detectors (Hall sensors on the board) are integrated into the valve control. The valve can also be pneumatically actuated by externally attached solenoid valves. The valve position is indicated mechanically and electrically (DUO LED) directly at the valve control. For heavyduty applications we recommend using a special steel cover (no indication of valve position). A pressure control valve effectively prevents the cover from bursting in case of air leakage. The electrical connection can be carried out directly by means of double-pole cables or with a plug connection. To protect the device against unauthorized tampering the cover can be sealed. In accordance with the valve control type, the following valve functions can be driven. Valve functions valve opening - closing clocking valve disk above clocking valve disk below All functions will be pneum. controlled. Pneum. opening and closing by spring power MAINTENANCE NOTE 56301XXX00_000_E.DOC/ Page 1

2 The valve control does not require maintenance. However, we recommend checking the tightness of the air connections at set intervals. If air leakage occurs within the valve control, the compressed air escapes into the open by way of the pressure control valve. ELECTRICAL INSTALLATION (ILL. 3, 4, 6) The electrical connection of the valve control is carried out by means of two unscreened two-wire lines. We recommend using the BUS line of Phönix Contact. It is possible to connect the BUS input and BUS output line with the valve control by means of two PG9-screw fittings or two plug connections. CAUTION: On principle electric installations are always to be carried out in idle condition. Electrical connection of the valve control with PG9 screw fitting (17) ill. 6 Strip about 15 mm of the outer insulation off the 2-wire control cable. Push hexagonal nut, clamping piece, seal bushing according to assembly drawing onto the control cable. Affix the control cable wires, acc. to connection layout, (ill. 3), up to stop to the outer cable insulation in the socket. Place socket upon cable plug and screw down with hexagonal nut. Pin connection of the Quickon socket: 1 = brown = + 24 V 2 = black = ground / GND Assembly drawing of the Quickon plugs: Ill Strip about 60 mm of the outer insulation off the control cable. 2. Strip the insulation of the control cable wires by about 10 mm and equip them with wire sleeves with 4-side crimping. Cut off projecting cable wires at the wire sleeves. CAUTION: Cable wires that have not been cut off lead to faulty contact making. 3. Unbolt the housing cover (23) (24) by rotary motion (bayonet catch) and take it off in upward direction. Lead BUS input and BUS output line separately by PG screw fittings (17) into the housing. 4. Unscrew the slotted bolt (13/1) (2ea.). 5. Remove the plug (13) from the board (2) and connect the control cable wires acc. to the connection layout (ill. 2) CAUTION: Push the wire sleeves of the control cable up to the end stop into the bushing of the plug, and clamp them afterwards. Pin connection of plugs (13) seal bushing Hexagon nut Socket cable plug clamping piece PUTTING INTO OPERATION IN 4 BIT MODE If different valve control generations are used in one system, appropriate measures have to be taken in accordance with the description INTERBUS valve control generations (page 5). Ill. 4 Ill Push the plug (13) onto the connecting board and tighten it with slotted screws (13/1). 7. Place the control cable in the valve control free of contact to the piston rod of the drive unit and clamp it free of tension by the PG9 screw fitting (17) (carry out tensile test by hand). If the drive of the valves is realized in 4 bit mode, the valve type can be adjusted directly via the valve - selection switch BCD (ill. 6). Programming by means of the CMD software of Phönix Contact is not necessary. 1. Adjust the valve type via the valve - selection switch 2. Remove the plug-in bridge (14) from the board (2) (ill. 6). By this the valve - selection switch and the 4 bit mode are activated. Electrical connection of the valve control with the Quickon socket (25 (26) ill. 4: 3. Apply service voltage (Techn. data, chart 8) 4. Connect compressed air hose Ø 6 x 1 to fitting (11) 56301XXX00_000_E.DOC/ Page 2

3 5. Check components for air leakage. 6. Check the valve function by manual operation of the 3/2 way solenoid valves (22). The manual actuation in the form of a slide switch is placed at the front side of the 3/2 way solenoid valves (22). ELECTRICAL ACTUATION The drive of the valves is realized by means of the drive signal MVA (chart 1). 1. Switch on operating voltage and cut in control air. 2. Check the valve functions according to the drive signal MVA and MVB (chart 1) 3. Compare position of the valve selection switch with instructions Chart 1 (Drawing Page 6 = view X ) Valve function valve drive valve codification: Valve funct. Solenoid v Drive signal Valve codification position MVA MVB Valve selection s. Closing MV Clocking UV MV2 1 0 Clocking OV MV3 0 1 Closing MV Closing MV Clocking UV MV2 1 0 Closing MV Clocking N OV MV3 0 1 Ext. solenoid position only with limit switch 3 Switching position for above opened double seat valve xxx 041 Chart 1 PUTTING INTO OPERATION IN 16 BIT MODE see use of valve control versions, page 5 Adjusting the valve type: Before putting into operation and when exchanging the board (2), in general the valve type is to be programmed by means of the CMD software according to the specifications in chart 1. Two bytes of data are available for adjusting the valve type as well as the special functions. Byte 0 serves for driving the solenoid valves and switching over into the planning mode, and byte 1 for input of the values of the function adjusted in byte 0. For adjusting the valve type, bit 4 (valve type) is to be set in byte 0. In addition to it, the relevant bits 0-3 (BCD coded) are set in byte 1. The valve code can be gathered from chart 1. Thus, the valve type has been programmed. Now the bits set before must be reset again. CAUTION: The value of bit 0 of byte 0 must be 0. The complete occupancy of the input / output bytes can be gathered from the charts 2 through Counter for the switching cycles of the valve (By this, possible maintenance records can be generated by means of logging the operational data). 2. Monitoring the maximum switching cycles of the valve. (By this, possible service messages can be generated by means of logging the operational data). 3. Running time monitoring Opening. By this, the running time required for opening the valve can be monitored and error messages be generated. 4. Running time monitoring Closing. By this, the running time required for closing the valve can be monitored and error messages be generated. The additional functions are to be parameterized with the following data: 1. Maximum switching cycles of valve 2. Maximum running time - Opening the valve 3. Maximum running time - Closing the valve In the CMD software the data allocation (2 bytes inputs and outputs) is assigned to the PLC inputs and outputs. If the functions are not desired, it will be unnecessary to assign every BIT to the PLC. Allocation of the functions: Output byte 0 CMD Bit no. Signal 0 MVA 1 MVB 2 Reserve 3 Reserve 4 Mode bit *1 5 Mode bit *1 6 Mode bit *1 7 Counter reset Chart 2 Bit, 6, 5, 4 Value Signal Normal operation Valve type Running time monitoring Opening in seconds Running time monitoring Closing in seconds Final value of counter in 1000-stepsvalues Reserve Reserve Reserve Output byte 1 CMD Bit no. Signal 0 Planning value 1 1 Planning value 2 2 Planning value 4 3 Planning value 8 4 Planning value 16 5 Planning value 32 6 Planning value 64 7 Planning value 128 Chart 3 Chart 4 Additional functions: The transmission protocol of the Interbus enables the following additional functions: 56301XXX00_000_E.DOC/ Page 3 Input byte 0 CMD Bit no. Signal 0 Proximity detection Valve 1 Proximity detection Valve open 2 Exceeding the running time 3 Reserve

4 Input byte 1 CMD 4 Reserve 5 Exceeding the counter 6 Counter multiplexing 0 =bit =bit Counter value bit 16 in 1-step-values Chart 5 Bit no. Signal 0 Counter value bit 0 / 8 in 1-step-values 1 Counter value bit 1 / 9 in 1-step-values 2 Counter value bit 2 / 10 in 1-step-values 3 Counter value bit 3 / 11 in 1-step-values 4 Counter value bit 4 / 12 in 1-step-values 5 Counter value bit 5 / 13 in 1-step-values 6 Counter value bit 6 / 14 in 1-step-values 7 Counter value bit 7 / 15 in 1-step-values Chart 6 ELECTRICAL ACTUATION The drive of the valves is realized by means of the drive signal MVA and MVB (chart 1). 1. Check valve functions according to the control signals. PROXIMITY DETECTION / VALVE POSITION INDICATION The proximity detection and the valve position indication should be checked along side the valve functions. PROXIMITY DETECTION The proximity detection for valve OPEN or CLOSED takes place without direct contact by the magnetic field of the ring magnets of the pulse generator with overlap of the Hall-sensors on the board (2) (ill. 5). In case of error messages, the mounting position of the pulse generator as well as the dimensions A and B (see data sheet) are to be checked acc. to valve size, or to be adjusted anew, respectively. DANGER When assembling the pulse generator, screw the cap into the piston rod up to the metallic stop. A cap that has not been screwed in completely leads to destruction of the housing cover, because of the stroke motion of the piston rod (23) (24) > Danger of injury Cap Valve position i di i Clocking above Clocking below Mechanical: Valve OPEN Valve CLSD Clocking above Clocking below = position indiation red = 1 Valve disk is = position indication red = 1 Valve disk is = Lifting position of the driving spindle = position indication green = position indication red = position indiation red = 1 Valve disk is = position indication red = 1 Valve disk is DISASSEMBLY/ASSEMBLY OF THE VALVE CONTROL WHEN EXCHANGING THE VALVE ACTUATION 1. Do not unscrew the fresh air pipe and the control cable or the plug connection from the valve control. 2. Unbolt the housing cover (23) (24) by rotary motion (bayonet catch) and take it off in upward direction. 3. Close 3-/2 way solenoid valve (22) by manual operation 4. Detach the air pipe from the supply (19). 5. Screw out pan head screws (4) 2ea.. 6. Remove the housing (7) and close with housing cover (23) (24). 7. Disassemble valve actuation 8. Assemble in reverse order, steps 7 to 1. DISASSEMBLY/ASS. OF BOARD (2) AND CONNECTOR PLATES (27A,27B,27C,27D) 1 Unbolt the housing cover (23) (24) by rotary motion (bayonet catch) and take it off in upward direction. 2. Close 3-/2 way solenoid valve by manual operation 3. Unscrew screws (13/1) (2ea.) and pull off plug connector (13) from the board (2). 4. Unscrew the Torx screws (10) (2ea.) (spanner T20). 5. Expand the board holders (BH) slightly outward to both sides and remove the board (2) with the connector plate (27a) (27b) in an upward direction. CAUTION: The O-rings (8) (5 ea.) and 9 (1 ea.) are fixed to he bottom side of the connector plate (27). Check their position and number when assembling. 6. Press together the snap-in pin tips (PT) (2ea.) and release the board (2) from the plug connection (PC) at the connector plate (27). 7. Assemble in reverse order, steps 6 to 1. Valve position indication Mode of indication: Electrical: = DUO LED on the board (2) Valve "OPEN = position indication "green Valve "CLSD = position indication "red Ill XXX00_000_E.DOC/ Page 4 DISASSEMBLY/ASSEMBLY OF THE 3/2 WAY SOLENOID VALVES (22) 1. Disassemble as described above, disassembly/assembly of the board (2) and connector plates (27a), (27 b), steps 1 through 6.

5 2. Unscrew the recessed head screws (18) (2ea.) and remove the 3/2 way solenoid valve (22) with gasket (GPG) (crosstip screwdriver PH 100). 3. Assemble in reverse order, steps 2 to 1 / 6 to 1. ASSEMBLY INSTRUCTIONS FOR 3/2 WAY SOLENOID VALVES (22) * Insert the gasket (GPG) at the guide pins with the hole and bead positioned toward the top left. * Align the 3/2 way solenoid valve (22) by way of the guide pins and fasten with recessed head screws (18) (2ea.). * CAUTION: Tighten the recessed head screws (18) alternately and evenly, starting at top left. QUALITY OF CONTROL AIR PRESSURE Solids content: Particle size: max. of 5 µm Particle number density: max. of 5 mg/m 3 (grade 3) Water content: Dew point +2 C (grade 3) Oil content: Oil-free max. of 25 mg/m 3 oil (grade 3) TECHNICAL DATA Bus system: Evaluation options: Evaluation of valve position, switching cycles, running time monitoring Address range: ** 1 32 Operating temperature: 10 to +60 C Appliance classes: II (Control head with cap transparent) according to DIN EN61140 I (Control head with cap stainless steel) (VDE ) International protection rating: according to DIN EN60529 Supply voltage: Max. current drawn: electrical connecting line: Cable connection - valve control: Proximity sensor: Control air pressure: Air flow rate: Material for housing: Material for cover: Material for sealing gaskets: Weight: electromagnetic compatibility: Indication at device: IP 67 (Control head with cap transparent) IP 65 (Control head with cap stainless steel) V DC 70 ma INTERBUS bus line green Cable cross section 1.5 sq.mm. PG 9 direct wiring with connector plug (13) or Quick. plug 2 Hall effect sensors 0.1 to 8 bar 140 l/min. (6 bar) ABS 6F Standard: ABS transparent Optional: (special steel) NBR 0.5 kg Test report FS/57.00/ Mechanical and LED indication of the valve position, LED bus indicator Chart 7 ** Note: The current absorption of the board, with simultaneous drive of all valves, results in a possible number of valves of 21 per loop. Since only in very few cases all valves are driven simultaneously, the number of valves per loop increases because of the simultaneity factor. This factor varies, depending on the process application. Interbus Loop Operational principle: Slave INTERBUS VALVE CONTROL GENERATIONS If different valve control generations are installed in one compound control system, the relevant bit mode will have to be adjusted or board V 1.4 will have to be replaced. 1. Generation of horizontal board arrangement Turning valve 4136.xxx.xxx xxx (ao ac) 4236.xxx.xxx xxx (ao sc) (ac so) 2. Generation V 1.4 of vertical board arrangement Turning valve x1.xxx 000 (ao sc) (ac so) x2.xxx 000 (ao ac) xx.xxx xxx Lifting valve x1.xxx 000 (ao sc) (ac so) x2.xxx 000 (ao ac) Double seat valve x1.xxx 000 (DSV/NT) x2.xxx 000 (DSV/OT) x6.xxx 000 (DSV/UT) x3.xxx 000 (DSV/OUT) Identification of same type no. by designation on the board V1.4 or V Generation V 2.0 of vertical board arrangement Turning valve x1.xxx 000 (ao sc) (ac so) x2.xxx 000 (ao ac) Lifting valve x1.xxx 000 (ao sc) (ac so) x2.xxx 000 (ao ac) Double seat valve x1.xxx 000 (DSV/NT) x2.xxx 000 (DSV/OT) x6.xxx 000 (DSV/UT) x3.xxx 000 (DSV/OUT) 4. Generation V 3.0 of vertical board arrangement compatible with V 2.0 same item no. as V 2.0 Designation on the board with V 3.0 (s. drwg. page 6) Changes: Expanded to valve function DSV - opening upwards. Board potted INTERBUS board only turning valves INTERBUS board V Compatible in the compound control system. The valve - selection switch is active. Replacement boards are no longer available. > will be replaced by complete valve controls type no xx.xxx 000 Compatible in the compound control system. The valve - select. switch is inactive. The allocation of the valve types is carried out via the log. INTERBUS board V With valve - selection switch With plug-in bridge = 16 bit mode Without plug-in bridge = 4 bit mode Standard version 56301XXX00_000_E.DOC/ Page 5

6 56301XXX00_000_E.DOC/ Page 6

7 Valve control versions IBU board for lifting valves Part No. Spare parts, allocation - item acc. to chart Arrangement of solenoid valves MV1, MV2, MV3 V.Contr.DSV/NT IBU 2STS THSA KAPG9 1MV ,17(2x),18(2x),19,20,21,22,23,27a MV1 V.Contr.DSV/OT IBU 2STS THSA KAPG9 2MV ,17(2x),18(4x),19(2x),22(2x),23,27b MV1, MV3 V.Contr.DSV/UT IBU 2STS THSA KAPG9 2MV ,17(2x),18(4x),19,20,21,22(2x),23,27c MV1, MV2 V.Contr.DSV/OUT IBU 2STS THSA KAPG9 3MV ,17(2x),18(6x),19(2x),22(3x),23,27d MV1, MV2, MV3 V.Contr.DSV/NT IBU 2STS THSA KAQS 1MV ,15(2x),16(2x),18(2x),19,20,21,22,23,25(2x),26(2x),27a MV1 V.Contr.DSV/OT IBU 2STS THSA KAQS 2MV MV1, MV3 14,15(2x),16(2x),18(4x),19(2x),22(2x),23,25(2x),26(2x),27b V.Contr.DSV/UT IBU 2STS THSA KAQS 3MV ,15(2x),16(2x),18(4x),19,20,21,22(2x),23,25(2x),26(2x), MV1, MV2 27c V.Contr.DSV/OUT IBU 2STS THSA KAQS 3MV (2x),16(2x),18(6x),19(2x),22(3x),23,25(2x),26(2x),27d MV1,MV2,MV3 V.Contr.DSV/NT IBU 2STS EHOS KAPG9 1MV ,17(2x),18(2x),19,20,21,22,24,27a MV1 V.Contr.DSV/OT IBU 2STS EHOS KAPG9 2MV , 17(2),18(4x),19(2x),22(2x),24,27b MV1, MV3 V.Contr.DSV/UT IBU 2STS EHOS KAPG9 2MV ,17(2x),18(4x),19,20,21,22(2x),24,27c MV1, MV2 V.Contr.DSV/OUT IBU 2STS EHOS KAPG9 3MV ,17(2x),18(6x),19(2x),22(3x),24,27d MV1, MV2, MV3 V.Contr.DSV/NT IBU 2STS EHOS KAQS 1MV ,15(2x),16(2x),18(2x),19,20,21,22,24,25(2x),26(2x),27a MV1 V.Contr.DSV/OT IBU 2STS EHOS KAQS 2MV MV1, MV3 14,15(2x),16(2x),18(4x),19(2x),22(2x),24,25(2x),26(2x),27b V.Contr.DSV/UT IBU 2STS EHOS KAQS 2MV ,15(2x),16(2x),18(4x),19,20,21,22(2x),24,25(2x),26(2x), MV1, MV2 27c V.Contr.DSV/OUT IBU 2STS EHOS KAQS 3MV (2x),16(2x),18(6x),19(2x),22(3x),24,25(2x),26(2x),27d MV1, MV2, MV3 SPARE PARTS Item Part name Material Part No. 1 Position indication ABS GN Coupling board / version V 2.0 (supersedes version V 1.4) O ring Ø 94 x 2.3 > supersedes Ø 96 x 2 NBR SW 70 Silicone Screw M6 x 16 DIN 912 (2ea.) O ring Ø 25 x 2.5 NBR black O ring Ø 44 x 2 NBR black Housing complete O ring Ø 3 x 2 (5ea.) NBR black O ring Ø 2 x 1.5 (1ea.) NBR black Screw JOT, WN 1451 K40 x 14 (2ea.) Plug connector Ger. RA 1/ Sound absorber special steel Connector piece, fourfold MC 1.5/4 STF 381 with screws 13/ Short-circuit bridge, 2-pin conical nipple Ø 19 x Ø 15 x Cable connection adapter PA 6.6 sw Cable connection PG9 PA 6.6 sw Screw W.plug connection pivoting RA 1/8, Ø 6 x Screw plug G 1/ Conical nipple Ø 13 x Ø 1,5 PVC non-rigid /2-way-solenoid valve with slide switch Housing cover, transparent MABS Housing cover, stainless steel Quickon IN plug Quickon OUT plug a Connector plate, not clockable b Connector plate, clocking above c Connector plate, clocking below d Connector plate, clocking above and below XXX00_000_E.DOC/ Page 7

OPERATING INSTRUCTIONS 5630 Valve control INTERBUSLOOP version for pneum. lifting valves with board version V 2.0 or V 3.0

OPERATING INSTRUCTIONS 5630 Valve control INTERBUSLOOP version for pneum. lifting valves with board version V 2.0 or V 3.0 Valve control versions IBU board for lifting Part No. valves V. Contr. LIFTV IBU 2STS THSA KAPG9 1MV 5630.401.000 000 V. Contr. LIFTV IBU 2STS THSA KAPG9 2MV 5630.402.000 000 V. Contr. LIFTV IBU 2STS THSA

More information

OPERATING INSTRUCTIONS 5630 Valve control INTERBUSLOOP version for pneum. turning valves with board version V 2.0 or V 3.0

OPERATING INSTRUCTIONS 5630 Valve control INTERBUSLOOP version for pneum. turning valves with board version V 2.0 or V 3.0 Valve control versions IBU board for Turning valves Part No. V. Contr. TURNV IBU 2STS THSA KAPG9 1MV 5630.701.000 000 V. Contr. TURNV IBU 2STS THSA KAPG9 2MV 5630.702.000 000 V. Contr. TURNV IBU 2STS THSA

More information

Operating Instructions

Operating Instructions Operating Instructions ASI Control Head for Lift and Turning Valves Subject to technical modifications and innovations. Rev. 6 ASI Steuerkopf für Hub- und Drehventile Beschreibung 100xxx / Doku / Elek

More information

Operating Instructions

Operating Instructions Operating Instructions ASI Control Head for Lift and Turning Valves Subject to technical modifications and innovations. Rev. 4 ASI Steuerkopf für Hub- und Drehventile Beschreibung 100xxx / Doku / Elek

More information

TopControl Continuous

TopControl Continuous 860 Electropneumatic positioner for pneumatically actuated control valves Type 860 can be combined with... Type 7 Type 70 Types 70/7/7K Type 800 Piston-controlled globe valve Piston-controlled angle seat

More information

Operating instructions - Translation of the original -

Operating instructions - Translation of the original - Operating instructions - Translation of the original - Single seat valve pneumatic operation KIESELMANN GmbH Paul-Kieselmann-Str.4-10 D - 75438 Knittlingen +49 (0) 7043 371-0 Fax: +49 (0) 7043 371-125

More information

Type Pneumatic Control Unit. Operating Instructions

Type Pneumatic Control Unit. Operating Instructions Pneumatic Control Unit Operating Instructions We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. Bürkert Werke GmbH

More information

Type Pneumatic Control Unit. Operating Instructions

Type Pneumatic Control Unit. Operating Instructions Pneumatic Control Unit Operating Instructions We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. Bürkert Werke GmbH

More information

Operating Instructions. Pneumatic Control Valve Low Temperature. Type Series GS3

Operating Instructions. Pneumatic Control Valve Low Temperature. Type Series GS3 Operating Instructions Pneumatic Control Valve Low Temperature Type 8026 Series GS3 With: Digital Positioner Type 8048 Electro-pneumatic Positioner Type 8047 Pneumatic Positioner Type 8047 Version: 03/2006

More information

Operating instructions - Translation of the original -

Operating instructions - Translation of the original - Operating instructions - Translation of the original - Single seat valve Two-way-valve Type: 5714 pneumatic operation KIESELMANN GmbH Paul-Kieselmann-Str.4-10 D - 75438 Knittlingen +49 (0) 7043 371-0 Fax:

More information

Operating Instructions. Angle Seat Control Valve. Type 7020

Operating Instructions. Angle Seat Control Valve. Type 7020 Operating Instructions Angle Seat Control Valve Type 7020 With: Digital Positioner Type 8048 Electro-pneumatic Positioner Type 8047 Pneumatic Positioner Type 8047 Version: 02/2006 Manual-7020e.doc Art.-No:

More information

Solenoid Valves Type 3963

Solenoid Valves Type 3963 Mounting and Operating Instructions Solenoid Valves Type 3963 Fig. 1 General Assembly, commissioning and operation of these devices may only be performed by experienced personnel. Proper shipping and appropriate

More information

Mounting and operating instructions EB 5801 EN. Electric Actuators Type 5801 (Rotary Actuator) Type 5802 (Linear Actuator)

Mounting and operating instructions EB 5801 EN. Electric Actuators Type 5801 (Rotary Actuator) Type 5802 (Linear Actuator) Electric Actuators Type 5801 (Rotary Actuator) Type 5802 (Linear Actuator) Linear Actuator with Type 3260 Control Valve Rotary actuator with lever system Linear actuator with Type 3321 (V2001) Control

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation Pneumatic Control Unit Pneumatische Ansteuerung Unité de commande pneumatique Operating Instructions Bedienungsanleitung Manuel d utilisation We reserve the right to make technical changes without notice.

More information

Intelligent Positioner

Intelligent Positioner Intelligent Positioner Construction The GEMÜ 1 µpos is a digital electro-pneumatic positioner for process valve control. Designed for simple, safe and quick use with valves with strokes < mm. The positioner,

More information

Operating instruction

Operating instruction Translation of the original Operating instruction Butterfly valve P D F a k 1 6 / 0 2 / 2 0 1 8 ENGLISH EN K I E S E L M A N N G m b H Paul-Kieselmann-Str. 4-10 75438 Knittlingen ( +49(0) 7043 371-0 7

More information

Single-Line Centralized Lubrication Systems

Single-Line Centralized Lubrication Systems 1-15-EN Single-Line Centralized Lubrication Systems For fluid grease, NLGI grades, PFE-15-1. PF-289 MFE2-KW6F-S1 U1 U2 U3 The layout of a single-line centralized lubrication system for grease is largely

More information

DSV. Operating Manual. Double Seal Butterfly Valve. Read and understand this manual prior to operating or servicing this product.

DSV. Operating Manual. Double Seal Butterfly Valve. Read and understand this manual prior to operating or servicing this product. Operating Manual DSV Double Seal Butterfly Valve Read and understand this manual prior to operating or servicing this product. www.sks-online.com UK DSV-UK2.qxp / 10.2005 Table of Contents: Page: 1.

More information

Table of contents. Table of contents. Overview of progressive distributor Distributor bridge without outlet...

Table of contents. Table of contents. Overview of progressive distributor Distributor bridge without outlet... Table of contents 4 Technical basics System description... 04-0-10-01 Construction, applications, advantages, function System design... 04-0-10-02 Design and installation of progressive systems Calculation

More information

Limit Switch Type 3776

Limit Switch Type 3776 Mounting and Operating Instructions Limit Switch Type 3776 Fig. 1 Edition: June 2014 EB 8368 EN Contents General notes 3 Model number and device index 3 Mounting 3 Mounting to SAMSON Type 3278 Rotary Actuators

More information

HS6B Series Subminiature Interlock Switch

HS6B Series Subminiature Interlock Switch HS6B Series Subminiature Interlock Switch HS6B features: Only 78 x 30 x 15mm Allows highest level of safety by having 3 contacts: dual load contacts + monitoring contact (ISO13849-1, EN954-1) Two actuator

More information

Compact I/O modules (IP20)

Compact I/O modules (IP20) Bus module MBK Thanks to its compact construction, the bus module MBK (IP20) can be easily mounted in shallow control panels, terminal boxes and distribution boxes. The simple construction with the lowest

More information

+ = Angle-seat Valve System for continuous control. Type 8802/2300 electro-pneumatically operated angle-seat valve

+ = Angle-seat Valve System for continuous control. Type 8802/2300 electro-pneumatically operated angle-seat valve Angle-seat Valve System for continuous control Type 8802/2300 electro-pneumatically operated angle-seat valve + = TWO YEAR WARRANTY on this valve system Burkert 8802 continuous control valve + = 2300 series

More information

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Type 3535 Three-way Valve with bellows seal and rod-type yoke (partial view) Mounting and Operating Instructions EB 8135/8136 EN Edition

More information

Progressive Central Lubrication Systems

Progressive Central Lubrication Systems Table of contents 4 Technical basics System description... 04-0-0-0 Construction, applications, advantages, function System design... 04-0-0-02 Design and installation of progressive systems Calculation

More information

Intelligent Positioner

Intelligent Positioner Intelligent Positioner Construction The GEMÜ epos digital electro-pneumatic positioner detects the valve position via its external LongLife travel sensor. It has a solid housing with protected operating

More information

Pneumatic control unit for decentralized automation of ELEMENT process valves

Pneumatic control unit for decentralized automation of ELEMENT process valves 890 Pneumatic control unit for decentralized automation of ELEMENT process valves Type 890 can be combined with... Compact design Integrated pilot valve with manual override Integrated control air routing

More information

Electropneumatic Converters i/p Converters Type 6111 Mounting and Operating Instructions EB 6111 EN

Electropneumatic Converters i/p Converters Type 6111 Mounting and Operating Instructions EB 6111 EN Electropneumatic Converters i/p Converters Type 6111 Fig. 1 Type 6111 in standard version Fig. Type 6111 mounted on a supply air manifold Fig. 3 Type 6111 in field enclosure Mounting and Operating Instructions

More information

Modular pneumatic valve unit

Modular pneumatic valve unit Modular pneumatic valve unit Compact design Modular configuration High flexibility Type 8640 can be combined with Simple exchange of valves (with option P-shut-off - also possible during operation) Type

More information

Remote Process Actuation Control System AirLINE WAGO Remote I/Os and Fieldbusses

Remote Process Actuation Control System AirLINE WAGO Remote I/Os and Fieldbusses Remote Process Actuation Control System AirLINE WAGO Remote I/Os and Fieldbusses Type 8644 can be combined with... Fully compatible with WAGO I/O Combination of Fieldbus, pilot valves and I/O modules High

More information

Operating Instruction:

Operating Instruction: Operating Instruction: Leakage - Butterfly valve with manual operation Types LSV 4365 LSV 4366 LSV 4367 LSV 4368 LSV 4369 LSV 4370 Kieselmann GmbH Paul-Kieselmann-Str. 4-10 75438 Knittlingen Telefon +49

More information

DELTA PR2. Operating Manual. Sampling Valve. Read and understand this manual prior to operating or servicing this product.

DELTA PR2. Operating Manual. Sampling Valve. Read and understand this manual prior to operating or servicing this product. Operating Manual DELTA PR2 Sampling Valve Read and understand this manual prior to operating or servicing this product. UK Declaration of Conformity for Valves and Valve Manifolds SPX Flow Technology

More information

Modular pneumatic valve island

Modular pneumatic valve island Modular pneumatic valve island Compact design Modular configuration High flexibility Simple exchange of valves (with P shut off, also possible during operation an option) Type 8640 can be combined with

More information

Valve Series V2001 Three-way Valve Type 3323

Valve Series V2001 Three-way Valve Type 3323 Valve Series V2001 Three-way Valve Type 3323 Fig. 1 Type 3323 Valve with mounted rod-type yoke (partial view) Edition January 1999 Mounting and operating instructions E 8113/8114 EN 1. Design and principle

More information

Safety Products. Safety Products. HS5E Series. HS5E Series Miniature Solenoid Locking Switch

Safety Products. Safety Products. HS5E Series. HS5E Series Miniature Solenoid Locking Switch HS5E Series HS5E Series Miniature Solenoid Locking Switch HS5E Key features include: World s smallest 4 contact solenoid interlock switch. (35 40 46 mm.) Four contacts. Gold-plated contacts. Spring lock

More information

KONEX Pneumatic Modular Gripping System KONEX Gripping force Torque Piston force (extended)

KONEX Pneumatic Modular Gripping System KONEX Gripping force Torque Piston force (extended) KONEX Gripping force 100 N Torque 0.9 Nm Piston force (extended) 250 N Application example KONEX weight-reduced, modular gripping system for economical automation in assembly and production KONEX P 50

More information

BR 31a Rack-and-pinion Actuator,

BR 31a Rack-and-pinion Actuator, Operating, assembly and maintenance instructions BR 31a Rack-and-pinion Actuator, SRP and DAP 1. General These instructions are intended to support the user in the assembly, maintenance, and repair of

More information

Operating instruction. Butterfly valve. Translation of the original ENGLISH

Operating instruction. Butterfly valve. Translation of the original ENGLISH Translation of the original Operating instruction Butterfly valve P D F a k 0 4 / 0 2 / 2 0 1 9 ENGLISH GB K I E S E L M A N N G m b H Paul-Kieselmann-Str. 4-10 75438 Knittlingen ( +49(0) 7043 371-0 7

More information

User Guide. Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC)

User Guide. Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC) User Guide Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC) version 04/2013 Content General Information 3 Warning 3 Scope of Supply 3 Overview 3 General safety details 4 Intended use 4

More information

RODLESS CYLINDER SERIES PU ACTUATORS

RODLESS CYLINDER SERIES PU ACTUATORS RODLESS CYLINDER SERIES PU 1 RODLESS CYLINDER SERIES PU RODLESS CYLINDER SERIES PU Series PU rodless cylinders have an internal strip for longitudinal tightness made of polyurethane (PU) with a harmonic

More information

HS1C Series Full Size Interlock Switch with Locking Solenoid. GS-ET-15 BG standard in Germany. HS1C Series Functionality

HS1C Series Full Size Interlock Switch with Locking Solenoid. GS-ET-15 BG standard in Germany. HS1C Series Functionality Full Size Interlock Switch with Locking Solenoid HSC Key features include: Rugged Aluminum Die-cast Housing With the actuator mounted on a movable door, and the switch on a machine, the door can be mechanically

More information

Type 2030, 2031, 2031 K, 2032, 2033, 2037

Type 2030, 2031, 2031 K, 2032, 2033, 2037 , 2031, 2031 K, 2032, 2033, 2037 Replacement of the seal set Conversion of the control function Wechsel von Dichtungssätzen Umbau der Steuerfunktionen Remplacement du jeu de joints Transformation de la

More information

Repair Manual and Spare Parts List

Repair Manual and Spare Parts List Pneumatic Drive Unit Type Techn. Doc. No. 352 and Accessories for Pipe Cutting Machine Darstellung kann vom Original abweichen Repair Manual and 580027000_Inst_en_Version_02 Repair General In general,

More information

Compact System NRGS 11-2 NRGS Original Installation Instructions English

Compact System NRGS 11-2 NRGS Original Installation Instructions English Compact System NRGS 11-2 NRGS 16-2 EN English Original Installation Instructions 810366-05 1 Contents Important Notes Page Usage for the intended purpose...4 Safety note...4 LV (Low Voltage) Directive

More information

aero 2 -IOM aero 2 ACTUATOR - INSTALLATION, OPERATION & MAINTENANCE MANUAL

aero 2 -IOM aero 2 ACTUATOR - INSTALLATION, OPERATION & MAINTENANCE MANUAL Instruction DP00226 May 2015 IMPORTANT SAFETY WARNINGS A. Before carrying out any repair or maintenance on the actuator, make sure that the pressure supply lines and electrical connections have been safely

More information

Operating instructions - Translation of the original -

Operating instructions - Translation of the original - Operating instructions - Translation of the original - KIESELMANN GmbH Paul-Kieselmann-Str.4-10 D - 75438 Knittlingen +49 (0) 7043 371-0 Fax: +49 (0) 7043 371-125 www.kieselmann.de sales@kieselmann.de

More information

Door Interlock Switches

Door Interlock Switches HS5B Series HS5B Series Miniature Interlock Switch HS5B features: mm x mm x 9mm Compact Housing Available with Contact Confi gurations (NO + NC or NC) Flexible Installation: By turning the head of the

More information

Mounting and Operating Instructions EB 8091 EN. Pneumatic Control Valve Type and Type Type with 120 cm 2 actuator

Mounting and Operating Instructions EB 8091 EN. Pneumatic Control Valve Type and Type Type with 120 cm 2 actuator Pneumatic Control Valve Type 3510-1 and Type 3510-7 Type 3510-1 with 120 cm 2 actuator Type 3510-7 with 120 cm 2 actuator and integrated positioner Type 3510-1 with 60 cm 2 actuator Fig. 1 Pneumatic control

More information

Butterfly valves Leakage butterfly valves

Butterfly valves Leakage butterfly valves Butterfly valves Leakage butterfly valves www.rodgerindustries.com RODGER INDUSTRIES INC. Size D1 D5 L1 L2 L3 Weight (kg) (Metric millimeters) 1" 22.9 50.5 68 34 95 1,21 1.5" 35.1 50.5 68 34 101 1.29 2"

More information

Electronic Circuit Breaker ESS20-0..

Electronic Circuit Breaker ESS20-0.. Electronic Circuit Breaker ES-0.. Description Electronic circuit breaker type ES-0.. is designed to ensure selective disconnection of individual loads in systems which are powered by a DC 4 V switch-mode

More information

HS1E Series Full Size Solenoid Locking Switches

HS1E Series Full Size Solenoid Locking Switches HS1E Series Full Size Solenoid Locking Switches AS-Interface Safety at Work Barriers Enabling Switches Door Interlock Switches X Series E-Stops Overview HS1E features: Basic unit and solenoid unit in one

More information

T 3965 EN Type 3965 Solenoid Valve Island To control pneumatic actuators

T 3965 EN Type 3965 Solenoid Valve Island To control pneumatic actuators T 365 EN Type 365 Solenoid Valve Island To control pneumatic actuators Application The Type 365 Solenoid Valve Island is a compact solution for the central control of pneumatic actuators in chemical and

More information

Free position locking flat and compact cylinder UFCD Series

Free position locking flat and compact cylinder UFCD Series Space-saving cylinder ensures safety during work in power failures or accidents. Free position locking flat and compact cylinder UFCD Series Free position locking flat and compact cylinder UFCD Series

More information

ORIGA SYSTEM PLUS Guides, Brakes and Valves for Modular Linear Drive Systems OSP Appendix to the Operating Instructions

ORIGA SYSTEM PLUS Guides, Brakes and Valves for Modular Linear Drive Systems OSP Appendix to the Operating Instructions ORIGA SYSTEM PLUS Guides, Brakes and Valves for Modular Linear Drive Systems OSP Appendix to the Operating Instructions TAll personnel who have anything to do with the OSP fitted with guides, brakes or

More information

Modular electrical and pneumatic automation system

Modular electrical and pneumatic automation system Modular electrical and pneumatic automation system Decentralised automatisation without control cabinet in protection type IP65 / IP67 Modular structure, also as central station with several decentralised

More information

Repair Manual 11/99 PS-34. Page 1

Repair Manual 11/99 PS-34. Page 1 Repair Manual /99 PS-4 Page Table of contents Index Technical Data page Special tools 4 Repair instructions, general 0 Chain brake 6 0 Centrifugal clutch 8 0 Oil pump 9-04 Ignition system - 0 Starting

More information

Type Operating Instructions. Angle Seat Motor Valve Compact. BM24C, BM24C/I BM24C/IOS, BM230C/IOS with and without spring return

Type Operating Instructions. Angle Seat Motor Valve Compact. BM24C, BM24C/I BM24C/IOS, BM230C/IOS with and without spring return Operating Instructions Angle Seat Motor Valve Compact Type 70 Valid For Actuators: BM4, BM5, BM30, BM4C, BM4C/I BM4C/IOS, BM30C/IOS with and without spring return Version: 08/004 W70e.doc Art.-Nr: 70 Bunsenstrasse

More information

Metal tube flowmeters. Series SC250. Metal Tube Flow Meters. Series SC250. Variable area flowmeter for liquids, gases and steam

Metal tube flowmeters. Series SC250. Metal Tube Flow Meters. Series SC250. Variable area flowmeter for liquids, gases and steam Metal tube flowmeters Variable area flowmeter for liquids, gases and steam Metallic or plastic tube with a robust construction Indication by means of magnetic coupling Scales calibrated in l/h, m 3 /h,

More information

Easytork Vane Actuator IOM

Easytork Vane Actuator IOM Easytork Vane Actuator IOM General Storage The Easytork Vane Actuator ( EVA ) is a high-quality product and as such must be handled, transported and stored with care. Prior to storage, inspect the actuator

More information

Operating instructions - Translation of the original -

Operating instructions - Translation of the original - Operating instructions - Translation of the original - Flow control valve Type: 57xx KIESELMNN GmbH Paul-Kieselmann-Str.4-10 D - 75438 Knittlingen +49 (0) 7043 371-0 Fax: +49 (0) 7043 371-125 www.kieselmann.de

More information

HS1E Series Full Size Interlock Switch with Locking Solenoid

HS1E Series Full Size Interlock Switch with Locking Solenoid HS1E Series HS1E Series Full Size Interlock Switch with Locking Solenoid HS1E Key features include: Basic unit and solenoid unit in one housing Plastic Housing: Light weight Ease of Wiring: All the terminal

More information

Series S847 Changeover switches featuring wiping, galvanically isolated, double-break contacts and positive opening operation Catalogue D47.

Series S847 Changeover switches featuring wiping, galvanically isolated, double-break contacts and positive opening operation Catalogue D47. Snap-action switches Changeover switches featuring wiping, galvanically isolated, double-break contacts and positive opening operation Catalogue D47.en Snap-action switches, S847 Series Dual changeover

More information

Mounting and Operating Instructions EB 3913 EN. Electropneumatic Converters i/p Converter Type

Mounting and Operating Instructions EB 3913 EN. Electropneumatic Converters i/p Converter Type Electropneumatic Converters i/p Converter Type 3913-0001 Fig. 1 Type 3913-0001 Electropneumatic Converter with pressure gauge and bracket Mounting and Operating Instructions EB 3913 EN Edition August 2011

More information

DELTA SD4. Operating Manual. Double Seal Valve. Read and understand this manual prior to operating or servicing this product.

DELTA SD4. Operating Manual. Double Seal Valve. Read and understand this manual prior to operating or servicing this product. Operating Manual Read and understand this manual prior to operating or servicing this product. Declaration of Conformity for Valves and Valve Manifolds SPX Flow Technology Rosista GmbH, Zechenstr. 49,

More information

Electromagnetic Flow Monitor magphant

Electromagnetic Flow Monitor magphant Technical Information TI 036D/06/en No. 50078457 Electromagnetic Flow Monitor magphant Monitoring and measurement Flow monitoring with selectable limit values (relay output) Flow measurement via 4...20

More information

Pump elements. Pump elements. Pump elements PE 60 / PE 120 / PE 170 (with pressure limiting valve)

Pump elements. Pump elements. Pump elements PE 60 / PE 120 / PE 170 (with pressure limiting valve) Table of contents Installation of the pump elements... 06-3-0-0 Functional description of the pump elements... 06-3-0-02 Overview pump elements... 06-3-0-03 with spring return PE 5 / PE 0 / PE 5 / PE 25

More information

Series 77 & 78. Compact & Modular Valves. solutions. Series 77 - Compact Valves. Series 77 - Sub-D. Series 77 - Fieldbus

Series 77 & 78. Compact & Modular Valves. solutions. Series 77 - Compact Valves. Series 77 - Sub-D. Series 77 - Fieldbus PNEUMATIC valves Series 77 & 78 Compact & Modular Valves Series 77 - Compact Valves Series 77 - LPP770 Series 77 - Sub-D Series 77 - Fieldbus Series 77 - LPP772 Series 77 - Coils & Plug-in sockets Series

More information

Honeywell VV, VP, VB & MS SERIES FOR VQ400M CLASS A VALVES PRODUCT HANDBOOK APPLICATION

Honeywell VV, VP, VB & MS SERIES FOR VQ400M CLASS A VALVES PRODUCT HANDBOOK APPLICATION Honeywell VV, VP, VB & MS SERIES FOR VQ400M CLASS A VALVES PRODUCT HANDBOOK APPLICATION The VV Series class A vent valves are intended to be used in combination with the VQ400M series combination valve.

More information

System Electropneumatic Converters (Proportional Valves) Electronic Process Controllers Signal Converters

System Electropneumatic Converters (Proportional Valves) Electronic Process Controllers Signal Converters System 6000 Electropneumatic Converters (Proportional Valves) Electronic Process Controllers Signal Converters Edition April 2018 Information Sheet T 6000 EN Electropneumatic Converters i/p converters

More information

3RG4 BERO Inductive Proximity Switches

3RG4 BERO Inductive Proximity Switches 3RG40 11 3RG40 11 0AA00 10/14 3RG40 11 0AB00 10/14 3RG40 11 0AF00 10/13 3RG40 11 0AF05 10/18 3RG40 11 0AF33 10/17 3RG40 11 0AG00 10/13 3RG40 11 0AG05 10/18 3RG40 11 0AG33 10/17 3RG40 11 0CC00 10/14 3RG40

More information

Installation & Operation Manual

Installation & Operation Manual Installation & Operation Manual (I-TORK PDS Series Pneumatic Actuator) PDS-M0108/1010 74-6, Chun Ui-Dong, Won Mi-Gu, Bucheon, Kyoung Ki-Do, Korea Tel : 82-2-855-1365, 66 Fax : 82-2-855-1367 E-mail : roy75@i-tork.com

More information

Door Interlock Switches

Door Interlock Switches HSE Series HSE Series Full Size Locking Switches Overview X Series E-Stops HSE features: Basic unit and solenoid unit in one housing Plastic Housing: Light weight Ease of Wiring: All the terminal screws

More information

VQ400M SERIES CLASS A COMBINATION VALVES PRODUCT HANDBOOK APPLICATION

VQ400M SERIES CLASS A COMBINATION VALVES PRODUCT HANDBOOK APPLICATION VQ400M SERIES PRODUCT HANDBOOK APPLICATION The VQ400M Series class A safety combination valves are used for control and regulation of gaseous fluids in gas power burners, atmospheric gas boilers, melting

More information

Butterfly valves ARI-ZIVA -Z / ARI-ZIVA -G. with notch lever. with worm gear. with electric rotary actuator rotork

Butterfly valves ARI-ZIVA -Z / ARI-ZIVA -G. with notch lever. with worm gear. with electric rotary actuator rotork Butterfly valves ARI-ZIVA -Z - Fig. 014 - Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range ARI-ZIVA -G - Fig. 015 - Free of maintenance butterfly valve with threaded eyelets

More information

Manual Electronic Identification Systems BIS Read/Write Heads C3-slk_716464_E_1110.p65 Deutsch bitte wenden!

Manual Electronic Identification Systems BIS Read/Write Heads C3-slk_716464_E_1110.p65 Deutsch bitte wenden! C3-slk_716464_E_1110.p65 1 Manual Electronic Identification Systems BIS s Deutsch bitte wenden! 2 No. 716 464 D/E Edition 1110 Subject to modification. Replaces edition 1104. Balluff GmbH Schurwaldstrasse

More information

JUMO DELOS SI. Precision pressure transmitter with switching contacts and display. Application. Brief description. Key features.

JUMO DELOS SI. Precision pressure transmitter with switching contacts and display. Application. Brief description. Key features. Data sheet 405052 Page 1/10 JUMO DELOS SI Precision pressure transmitter with switching contacts and display Application Food & pharma CIP/SIP systems Machine and system construction Air conditioning and

More information

VE Series. Class "A" Gas Valves. Product handbook APPLICATION CONTENTS. General. Technical. Installation and operation. Various

VE Series. Class A Gas Valves. Product handbook APPLICATION CONTENTS. General. Technical. Installation and operation. Various Class "A" Gas Valves Product handbook APPLICATION These series class A gas valves are used for control and regulation of gaseous fluids in gas power burners, atmospheric gas boilers, melting furnaces,

More information

Metso High Consistency Sampler Metso Nove H. Installation & Owner s Manual K10196 V1.1 EN

Metso High Consistency Sampler Metso Nove H. Installation & Owner s Manual K10196 V1.1 EN Metso Nove H Installation & Owner s Manual K10196 V1.1 EN Table of contents Warnings & safety information 3. Actions during operation 19 Recycling and disposal 1. Introduction 7 1.1. General description...7

More information

Globe Valve Type Fig. 1 Type 3241 Globe Valve. Mounting and Operating Instructions EB EN

Globe Valve Type Fig. 1 Type 3241 Globe Valve. Mounting and Operating Instructions EB EN Globe Valve Type 3241 Fig. 1 Type 3241 Globe Valve Mounting and Operating Instructions EB 8015-1 EN Edition July 2012 Contents Contents Page 1 Design and principle of operation.................... 4 2

More information

Butterfly valves. ARI-ZIVA -Z - Fig Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range

Butterfly valves. ARI-ZIVA -Z - Fig Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range ARI-ZIVA -Z - Fig. 014 - Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range ARI-ZIVA -Z / ARI-ZIVA -G Butterfly valves ARI-ZIVA -G - Fig. 015 - Free of maintenance butterfly

More information

Installation and operating manual

Installation and operating manual LK product no: 901002 and 901102 501002 and 501102 (JIS) Article no: 74500 Revision: 9 Article no: 74500 Revision: 9 2 (23) Contents 1. General information... 5 2. Safety precautions... 5 2.1 Significance

More information

MACH 16 VALVES DISTRIBUTORS

MACH 16 VALVES DISTRIBUTORS MACH 16 VALVES Available in size 1/8 only, versions 5/2 and 5/3 and with pneumatic and solenoid actuation. The mach 16 valve is a typical small size valve, only 16 mm wide, with excellent performance 750

More information

Electronic Limit Switch Type

Electronic Limit Switch Type Electronic Limit Switch Type 3738-20 with optional solenoid valve for on/off rotary actuators Application Electronic limit switch for on/off applications to indicate the end position of rotary actuators.

More information

ELADOS EMP III Diaphragm Pump type

ELADOS EMP III Diaphragm Pump type ELADOS EMP III Diaphragm Pump type 00800-01200 Mechanical stroke adjustment Stroke frequency regulation Pulse control Pulse multiplication and division Pulse memory Standard signal control Empty signal

More information

HS1B Series Full Size Interlock Switch. GS-ET-15 BG standard in Germany. Part Number Key

HS1B Series Full Size Interlock Switch. GS-ET-15 BG standard in Germany. Part Number Key HSB Series Full Size Interlock Switch HSB features: Rugged aluminum die-cast housing Direct Opening Action: If the door is forced open, the contacts are disconnected even if they are welded or stuck Available

More information

ZE ZE ZE. Simplex expanding wedge brake Assembly and Maintenance Instructions

ZE ZE ZE. Simplex expanding wedge brake Assembly and Maintenance Instructions Simplex expanding wedge brake Assembly and Maintenance Instructions Simplex expanding wedge brake Assembly and Maintenance Instructions Edition 1 This publication is not subject to any update service.

More information

Hydraulic clamping elements

Hydraulic clamping elements Hydraulic clamping elements hydraulic 3 Contents Product group 3 Hollow piston cylinder single-acting 3.1403 3.2130 Sliding clamp single-acting compact classic 3.2202 3.2204 Angular clamping element single

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS Emergency Cord Switch Type PRS Device identification No.: 91.054 033.001, /.101 and /.201 OPERATING INSTRUCTIONS 2 CE Sign and Conformity The device meets the requirements of the valid European and national

More information

Mounting and Operating Instructions EB 8111/8112 EN. Valve Series V2001 Globe Valve Type 3321

Mounting and Operating Instructions EB 8111/8112 EN. Valve Series V2001 Globe Valve Type 3321 Valve Series V2001 Globe Valve Type 3321 Fig. 1 Type 3321 Valve with mounted rod-type yoke for pneumatic or electric actuators (partial view) Mounting and Operating Instructions EB 8111/8112 EN Edition

More information

ThinkTop DeviceNetTM VDC DeviceNet is a Trademark of the Open DeviceNet Vendor Association, Inc. (ODVA).

ThinkTop DeviceNetTM VDC DeviceNet is a Trademark of the Open DeviceNet Vendor Association, Inc. (ODVA). PD 65493 GB1 20001-01 ThinkTop DeviceNetTM 11-25 VDC DeviceNet is a Trademark of the Open DeviceNet Vendor Association, Inc. (ODVA). Application The ThinkTop is designed to ensure optimum valve control

More information

Mounting and operating instructions EB Pneumatic Control Valve Type and Type Globe Valve Type 3522 ANSI Class 300

Mounting and operating instructions EB Pneumatic Control Valve Type and Type Globe Valve Type 3522 ANSI Class 300 Pneumatic Control Valve Type 3522-1 and Type 3522-7 Globe Valve Type 3522 ANSI Class 300 Fig. 1 Type 3522-7 Control Valve with integrated positioner Mounting and operating instructions EB 8822 Edition

More information

SPT- I / U PRESSURE TRANSMITTER for general applications

SPT- I / U PRESSURE TRANSMITTER for general applications Fields of application Design Examples Hydraulics Air conditioning and heating Testing technology Industrial robots Process controlling Water technology Pneumatics Description The pressure transmitters

More information

REMOVING CYLINDER HEAD COVER (VALVE COVER) - AS OF MY 2004 (CAYENNE TIP, CAYENNE MAN) > PRELIMINARY WORK > PRELIMINARY WORK

REMOVING CYLINDER HEAD COVER (VALVE COVER) - AS OF MY 2004 (CAYENNE TIP, CAYENNE MAN) > PRELIMINARY WORK > PRELIMINARY WORK Page 1 of 9 CYLINDER HEAD, VALVE DRIVE 15 82 21 REMOVING CYLINDER HEAD COVER (VALVE COVER) - AS OF MY 2004 (CAYENNE TIP, CAYENNE MAN) > PRELIMINARY WORK > PRELIMINARY WORK 1. Remove engine compartment

More information

Operating instructions Rotary actuators M135 M140 M150 M180. June 2012 / / EN

Operating instructions Rotary actuators M135 M140 M150 M180. June 2012 / / EN Operating instructions Rotary actuators M135 M140 M150 M180 June 2012 / 118614 / EN General information General information Proof of amendment Copyright Subject to alterations Manufacturer Version Date

More information

Operating Instruction for Flowmonitor. Model: DF-WM

Operating Instruction for Flowmonitor. Model: DF-WM Operating Instruction for Flowmonitor Model: DF-WM 1. Contents 1. Contents... 2 2. Note... 3 3. Instrument Inspection... 3 4. Regulation Use... 4 5. Operating Principle... 5 6. Mechanical Connection...

More information

86740/ /2-way piston valves

86740/ /2-way piston valves > > ort size: DN 8... 50, G1/4... 2 (ISO G/NT) > > Valve operates without differential pressure (Zero delta ) > > Suitable for vacuum > > Damped operation > > Valve piston with TFE guide-ring Technical

More information

Injection Oilers, Micro Pumps

Injection Oilers, Micro Pumps Injection Oilers, Micro Pumps 1-5012-4-US for minimal quantity metering Magnetic piston pump Injection oiler Micropump Grease metering P Metering pumps deliver and meter out lubricants. This piston pumps

More information

bar -20 C C ( C for high temperature version) 1000 mm

bar -20 C C ( C for high temperature version) 1000 mm Technical details Cylinders > piston rod cylinders > ISO 15552, double acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C... +80 C ( 0... +150 C for high temperature

More information

The specified data apply only if actuators/signal indicators are combined with contact blocks and lamp sockets within the same product range.

The specified data apply only if actuators/signal indicators are combined with contact blocks and lamp sockets within the same product range. General data QR control component range For a mounting hole diameter of.3 mm to IEC 60947 50V/10A max. Water-jet proof IP65 collar shapes The lamps of the pushbuttons can also be replaced from the front

More information

ELADOS EMP III Diaphragm Pump type

ELADOS EMP III Diaphragm Pump type ELADOS EMP III Diaphragm Pump type 00160-00540 Mechanical stroke adjustment Stroke frequency regulation Pulse control Pulse multiplication and division Pulse memory Standard signal control Empty signal

More information