Structural analysis of a wind turbine and its drive train using the flexible multibody simulation technique

Size: px
Start display at page:

Download "Structural analysis of a wind turbine and its drive train using the flexible multibody simulation technique"

Transcription

1 Structural analysis of a wind turbine and its drive train using the flexible multibody simulation technique J. Peeters 1, D. Vandepitte 2, P. Sas 2 1 Hansen Transmissions International, Leonardo da Vincilaan 1, B-2650 Edegem, Belgium jpeeters@hansentransmissions.com 2 K.U.Leuven, Department of Mechanical Engineering, Celestijnenlaan 300 B, B-3001, Heverlee, Belgium Abstract This article demonstrates the application of a generic methodology, based on the flexible multibody simulation technique, for the dynamic analysis of a wind turbine and its drive train, including a gearbox. The analysis of the complete wind turbine is limited up to 10 Hz, whereas the study of the drive train includes frequencies up to 1500 Hz. Both studies include a normal modes analysis. The analysis of the drive train includes additionally a response calculation for an excitation from the meshing gears, a Campbell analysis for the identification of possible resonance behaviour and a simulation of a transient load case, which occurs as a sudden torque variation caused by a disturbance in the electrical grid. 1 Introduction During the last decades, the interest for using renewable energy sources for electricity generation increased [1]. One of its results is a boom in the wind turbine industry since ten years. Figure 1 shows how the global installed wind power capacity reached 59.3 GW at the end of 2005, of which about 20% had been installed in that year. This rapid growth is expected to continue in the coming years and to drive new technological improvements to further increase the capacity and reduce the cost of wind turbines. In their design calculations, the wind turbine manufacturers use dedicated software codes to simulate the load levels and variations on all components in their machines. Peeters [3] gives an overview of the existing traditional simulation codes. He concludes that the concept of the structural model of a wind turbine in all these codes is more or less similar and that the behaviour of the complete drive train (from rotor hub to generator) is typically represented by only one degree of freedom (DOF). This DOF represents the rotation of the generator and, consequently, the torsion in the drive train. Peeters describes additionally the consequences of using this limited structural model for the simulation of drive train loads. The output of the traditional simulations lacks insight in the dynamic behaviour of the internal drive train components. De Vries [4] also raises the lack of insight in local loads and stresses in a drive train and the insufficient understanding of the design loads. He relates furthermore a series of gearbox failures in wind turbines to these consequences of simulating with a limited structural model. More insight can be gained from a more detailed simulation approach. Peeters [3] presents a generic methodology for this, which is based on three multibody system (MBS) modelling approaches. 3665

2 3666 PROCEEDINGS OF ISMA2006 [MW] Figure 1: The evolution of the global cumulative installed wind power capacity from 1995 to 2005 [2]. The first approach is limited to the analysis of torsional vibrations only. The second technique offers a more realistic representation of the bearings and the gears in the drive train and its generic implementation can be used for both helical and spur gears in parallel and planetary gear stages. The third method is the extension to a flexible MBS analysis, which yields information about the elastic deformation of the drive train components in addition to their large overall rigid-body motion. The implementation of the different models was done in LMS DADS Revision 9.6 [5] (DADS). This article presents an application of the second and third technique for the analysis of a drive train in a wind turbine. This example includes: a normal modes analysis for the determination of eigenmodes and eigenfrequencies (1) of the wind turbine and (2) in the drive train a response calculation for an excitation from the meshing gears a Campbell analysis for the identification of possible resonance behaviour a simulation of a transient load case 2 Drive train layout and model implementation Figure 2 shows the wind turbine for the present application. It is a generic example of which the results are representative for a modern wind turbine with a gearbox. The drive train has one main bearing integrated in the gearbox carrying the wind turbine rotor. The generator is a doubly fed induction generator (DFIG) and the gearbox design is a combination of two planetary stages with one high speed parallel stage. The wind turbine rotor is connected to the planet carrier of the first planetary stage. This stage has spur gears and its ring wheel is fixed in the gearbox housing. This housing is assumed to be rigid as well as its connection to the bed plate. This latter frame supports also the generator and rests on the yaw bearing, which connects the complete nacelle with the tower. The second gear stage in the gearbox is a helical planetary stage. Its planet carrier is driven by the sun of the first stage and its ring wheel is also fixed in the gearbox housing. The sun of this stage drives the gear of the third stage, which is a parallel stage with helical gears. The

3 ROTATING MACHINERY:DYNAMICS 3667 pinion of this stage rotates at the speed of the generator. A brake disk is mounted on this output shaft and a flexible coupling connects it with the input shaft of the generator. Since only the parallel gear stage causes a change in the direction of rotation, the high speed pinion and the generator rotate in the opposite direction of the rotor. The reaction torque of the gearbox on the bed plate is therefore slightly larger than the input torque. This torque acts in the same direction as the rotation of the rotor, which is clockwise when looking at the wind turbine in the direction of the wind. The torque on the generator support acts in the other direction. rotor hub high speed planetary stage low speed planetary stage bed plate yaw bearing high speed parallel stage flexible coupling generator brake disk Figure 2: Simplified representation of the three bladed wind turbine with a zoom on its drive train. The model of the wind turbine consists of: 1. a model of the gearbox, which is a system of rigid bodies with six DOFs per body: the formulations for the gear contacts and the bearings are based on a synthesis of the work of Kahraman [6] and of Lin and Parker [7]; 2. a brake disk, which is modelled as an additional body clamped on the pinion; 3. a flexible coupling between the high speed shaft of the gearbox and the generator, which is considered as very flexible in all directions, except for its torsional deformation and, therefore, it is modelled as a torsional spring; 4. a rigid body with only one rotational DOF to represent the generator: the generator is furthermore free to rotate;

4 3668 PROCEEDINGS OF ISMA a model of the rotor and the tower, which differs depending on the frequency range of the analysis (cfr. below). 1. [ 0-10 Hz] For the calculation of the wind turbine s response in a frequency range up to 10 Hz, which is typically the limit in the traditional simulations, it is necessary to include a realistic representation of the structural properties of the rotor and the tower. This is done by using a flexible multibody approach for these bodies. Both the rotor and the tower have six rigid-body DOFs and, furthermore, an extra set of DOFs to represent the internal deformations of these components. The latter DOFs of the so-called flexible bodies are derived from an FE model of the rotor and the tower respectively, using the CMS technique [8, 9]. The set of component modes is composed such that it accurately represents the dynamic behaviour of the individual components up to 10 Hz. This requires a consideration of four pairs of normal bending modes for each blade and the first ten normal modes of the tower. The remainder of this article describes the results of a normal modes analysis for this model. 2. [ Hz] The analysis of the drive train loads in a frequency range up to 1.5 khz 1 requires - in theory - the consideration of all rotor and tower modes up to approximately 3 khz. However, since this is an impracticable task and since both the rotor and the tower have more than ten modes below this frequency range, it is assumed that they will act as a large inertia with respect to an excitation at higher frequencies. Therefore, instead of adding two flexible bodies for the rotor and the tower, only one rigid body with six DOFs is included to represent the large inertia of the rotor. The tower is considered as a rigid ground, which supports the gearbox and the generator. This implies no need for an additional body to represent the tower. The remainder of this article describes three types of analysis for this model: a normal modes analysis, a frequency response analysis and a transient load simulation. 3 Discussion of the analyses 3.1 Low frequency range: [ 0-10 Hz] Table 1 summarises the normal modes calculated for the flexible multibody model of the wind turbine in the frequency range [ 0-10 Hz]. These results correspond to the typical results, which can be calculated in a traditional wind turbine simulation code. The 8th, 14th and 23rd mode are the respective rotor torsion modes or drive train modes. These modes have the biggest influence on the torque in the drive train and are determined by a combined effect of the following parameters, as demonstrated by Peeters [3]: 1. the (distributed) rotor inertia and flexibility (including the pitch angle and rotor position) 2. the drive train stiffness 3. the generator inertia 4. the coupling between the drive train and the tower top (e.g. the gearbox support and the generator characteristic) 5. the (distributed) tower inertia and flexibility 1 This work focusses on a range up to 1.5 khz, which is considered to be more than sufficient, since 1 khz is generally the maximum for the gear mesh excitation frequencies.

5 ROTATING MACHINERY:DYNAMICS 3669 No. Description Eigenfrequency (Hz) 0 rigid-body mode (drive train rotation) 0 1 1st tower longitudinal st tower transversal st asymmetric rotor flap/yaw (A) st asymmetric rotor flap/tilt (B) st symmetric rotor flap (C) st asymmetric rotor edge (B) st asymmetric rotor edge (C) st rotor torsion (A) nd asymmetric rotor flap/tilt + 2nd tower bending nd asymmetric rotor flap/yaw + 2nd tower bending nd asymmetric rotor flap/yaw + 1st tower torsion nd symmetric rotor flap nd asymmetric rotor flap/tilt nd rotor torsion nd asymmetric rotor edge (B) nd asymmetric rotor edge (C) rd asymmetric rotor flap/yaw + tower torsion rd asymmetric rotor flap/tilt rd symmetric rotor flap rd asymmetric rotor flap/yaw + 3rd tower bending rd asymmetric rotor flap/tilt + 3rd tower bending rd asymmetric rotor flap/yaw + 2nd tower torsion rd rotor torsion rd asymmetric rotor edge (B) rd asymmetric rotor edge (C) th asymmetric rotor flap/yaw th symmetric rotor flap th asymmetric rotor flap/tilt 10.3 Table 1: Results of a normal modes analysis of the wind turbine model with one blade in horizontal position, all blades pitched for normal operation and a pinned generator (= free to rotate). 3.2 Medium frequency range: [ Hz] Normal modes analysis Table 2 shows the eigenfrequencies calculated for the rigid multibody model of the wind turbine in the frequency range [ Hz]. The eigenfrequencies are classified according to the location of the nodes in the corresponding mode shapes and, additionally, for the planetary stages according to their type. The types of eigenmodes in the planetary stages are [7]: rotational modes: the corresponding mode shapes have pure rotation of the carrier, ring and sun and all planets have the same motion in phase. translational modes: the corresponding mode shapes have pure translation of the carrier, ring and sun. out-of-plane modes: the corresponding mode shapes have an out-of-plane component in translation and/or rotation of the carrier, ring, sun and/or planets.

6 3670 PROCEEDINGS OF ISMA2006 No. Global mode , , No. High speed planetary stage Rotational Translational Out-of-plane mode mode mode (m=1) (m=2) , , , No. Parallel stage No. Low speed planetary stage Rotational Trans- Out-of-plane mode lational mode (m=1) mode (m=2) ,12, Table 2: Eigenfrequencies (Hz) of the rigid multibody model of the wind turbine in the frequency range [ Hz] ( m denotes the multiplicity of the modes in the planetary stages). The category of global modes are those modes, for which the deformation cannot be attributed to a single gear stage: The global mode at 5.6 Hz corresponds to a torsional deformation of the drive train or a so-called drive train mode. However, as discussed in section 3.1, it is inaccurate to calculate such modes without the consideration of the rotor flexibility. Therefore, this mode is not considered as a relevant result. The double mode at 32 Hz corresponds to a tilting motion of the rotor in the main bearing. Again, an omission of the rotor flexibility for the calculation of this mode is inaccurate, since the flapwise rotor modes have a determining influence. Consequently, also this double mode is not considered as a relevant result. The global mode no. 5 at 68 Hz corresponds to the torsional deformation of the flexible coupling. This is the first relevant internal eigenmode for this particular drive train. Therefore, in the remainder of this text, it is considered to be sufficient to focus in the frequency response analyses on a frequency range starting from 50 Hz.

7 ROTATING MACHINERY:DYNAMICS 3671 The out-of-plane modes in the low speed planetary stage (at 227 Hz and 443 Hz) are further not considered to be relevant, since they cannot be excited by lack of axial forces on the spur gears in this stage Frequency response analysis This section describes how the results of the normal modes analysis should be interpreted in order to avoid resonance and, furthermore, it demonstrates how the drive train loads can be simulated for a sinusoidal load excitation. Both analyses imply a calculation of the frequency response. In order to avoid resonance, it is important to know which eigenmodes can considerably influence the loads in the drive train. This means that in one way or another there should be a coupling between these modes and a source of excitation. One known excitation source is the once-per-tooth pattern in a gear mesh, which excites at the so-called gear mesh frequency [10]. The coupling with such an excitation can be estimated from a detailed interpretation of the mode shapes, although, this is not straightforward. An easier method is to calculate a frequency response function (FRF) between the gear mesh excitation and a specific load in the drive train and check which eigenmodes lead to amplified load levels. This is demonstrated for the gear mesh excitation in the high speed planetary stage. The excitation is considered here as a variation of an input torque at the high speed sun. The input torque is a multisine with a minimal frequency of 50 Hz, according to the statement above. The upper frequency limit is 2.0 khz, which guarantees a proper excitation at all frequencies in the range from 50 to 1.5 khz. Figure 3 shows the spectrum of the multisine signal. The DADS solver calculates the output loads for this signal using a time integration procedure. A maximum time step of second is chosen. The numerical integration is only possible with a certain amount of damping in the drive train, which is included by adding a viscous damper element to the DADS model. The damping defines the amplitudes of the response, especially at the eigenfrequencies. Since the determination of the damping values is not within the scope of this analysis, the responses are only considered qualitatively. PSD [db/hz] Frequency [Hz] Figure 3: Power spectrum of the torque excitation signal used in the FRF calculations. Figure 4 shows the FRFs calculated for the torque excitation of the sun in the high speed planetary stage. The torque on the high speed pinion and on the two suns are the respective outputs in these calculations. Note that the FRF to the torque at the high speed sun is a direct FRF. The maximum frequency in these plots is only 1.0 khz, since no relevant amplified torque levels are identified at higher frequencies. The analysis of these results, leads to the following conclusions:

8 3672 PROCEEDINGS OF ISMA2006 PSD [db/hz] Frequency [Hz] (a) FRF to the torque at the high speed pinion. PSD [db/hz] Frequency [Hz] (b) FRF to the torque at the high speed sun. PSD [db/hz] Frequency [Hz] (c) FRF to the torque at the low speed sun. Figure 4: Response calculation for a gear mesh excitation in the high speed planetary stage, which is applied as a sinusoidal torque excitation of the high speed sun.

9 ROTATING MACHINERY:DYNAMICS For the high speed pinion, mainly the local modes at 430 Hz and at 562 Hz are dominant in the torque response (cfr. figure 4(a)). 2. The direct FRF to the torque on the sun of the high speed planetary stage, indicates that mainly the local modes in the parallel stage, at 346 Hz and 430 Hz respectively, can lead to a considerable torque amplification (cfr. figure 4(b)). This indicates the importance of analysing the drive train as a whole. The analysis of an individual gear stage yields insight in its local modes, but it does not permit to determine the mutual interaction between dynamic loads in different stages. 3. The torque spectrum at the low speed sun is dominated by one local mode in the parallel stage (346 Hz), one translational mode in the low speed planetary stage (305 Hz) and by six local modes in the range [ Hz]. 4. The global modes at 68 Hz and 140 Hz contribute also to the torque response in the different gear stages, albeit considerably less than the so-called local modes. The excitation signal used in this analysis has a broadband spectrum in order to get an overall idea about which eigenmodes can lead to amplified torque levels. However, for a particular speed of the drive train, the gear mesh excitation frequency in the high speed planetary stage is exactly known. This permits to determine whether it coincides with an important eigenfrequency. Figure 5 demonstrates this procedure. It is a Campbell diagram, which indicates how the gear mesh frequency varies with the rotational speed of the rotor in the wind turbine. In addition to the actual gear mesh frequency, its first and second harmonic are also plotted as excitation frequencies. The eigenfrequencies included in this figure are the horizontal lines, which correspond to the dominating peaks from the direct FRF in figure 4(b). These frequencies are considered as the only important frequencies for this excitation with respect to possible torque amplifications in this gear stage. The intersection of lines indicate possible resonances. For a fixed-speed wind turbine the focus can be limited to a single speed. However, modern variable-speed wind turbines require the consideration of a certain speed range. For the present example, two cursors indicate such a speed range for the wind turbine rotor from 10 to 20 RPM. In this range, the following intersections are found: 1. the gear mesh frequency intersects the eigenfrequency at 140 Hz; 2. the first harmonic intersects the eigenfrequency at 302 Hz; 3. the second harmonic intersects four eigenfrequencies above 300 Hz. The results from this analysis are valuable input for assessing whether or not a drive train resonance can occur as a result of this excitation. The same analysis can be performed for other excitations and with the focus on other loads. It is obvious that avoiding all intersections between excitations and eigenfrequencies in a quite broad speed range is impossible. However, keeping in mind that the actual gear mesh frequencies are usually more important than their harmonics, the insights from the calculated FRFs yield already valuable information for the evaluation of a drive train design in order to avoid severe resonances. To gain more experience in this evaluation and, more generally, to gain further confidence in the present analysis techniques and their results, it is recommended to perform sufficient experimental validation measurements. A more detailed numerical investigation of the intersections in the Campbell diagram at a particular frequency, requires a prediction of the amplified load levels. This simulation requires an accurate consideration of the drive train damping values and an appropriate description of the excitation signal, which represents the transmission error in the gear mesh. Since this is not within the scope of the present article, the load simulation at resonance is not further elaborated.

10 3674 PROCEEDINGS OF ISMA2006 Eigenfrequencies [Hz] Rotor speed [RPM] Figure 5: Campbell diagram which indicates the position of the gear mesh frequency and its harmonics (inclined lines) of the second gear stage for a varying rotor speed, in comparison to the dominant eigenfrequencies (horizontal lines) from the direct torque response function in figure 4(b). The cursors (vertical lines) indicate the speed range during operation Simulation of a transient load case This section demonstrates how the load simulation with a detailed drive train model yields the desired insight in its behaviour and gives much more and more accurate information than obtained with the simulations in the traditional wind turbine design codes. For the present demonstration, the simulation of a transient load case is used. An accurate description of the external forces during a transient load case requires a complete model of the wind turbine system, including a model for the generator, for the aerodynamics,... Since these models are not available, an assumption is made here for the load excitation. This is sufficient for the present illustration. An integration of the presented drive train model in a traditional wind turbine design code can help in further refining the load simulations. The simulated transient load case includes a sudden torque variation at the generator with a high amplitude. This phenomenon can have various causes, such as disturbances in the electrical grid as described by Soens et al [11] and Seman et al [12, 13]: e.g. frequency disturbances, a voltage dip or swell and a network short circuit. In the present example, the torque variation occurs during a start-up of the wind turbine. This mean that the generator torque would normally be increasing as shown in figure 6(a). Firstly, the simulation is done for this reference signal, i.e. without the sudden torque peak. The slope of this signal equals 1 knm/second and the time series has a length of 1 second. Subsequently, the torque variation is added at t = 0.5 s, which is visible in figure 6(b). The shape and the duration of the torque variation may largely differ for various grid disturbances and is furthermore highly dependent on the type of generator. Here, a damped sinusoidal variation with a frequency of 20 Hz is considered; it has a duration of two periods (100 ms) and a maximum amplitude of 9.1 knm. This example is based on the description in [13] of the generator torque variation during a network short circuit in a DFIG with an over-current protection system.

11 ROTATING MACHINERY:DYNAMICS 3675 (a) 1st load case: a normal start-up (reference signal) (b) 2nd load case: a grid disturbance during start-up Figure 6: Generator torque used in the simulations of two transient load cases. Figure 7 shows a comparison of the simulations calculated for the two load cases. In this example, the focus is put on: 1. the level of the torque, which acts on the pinion of the high speed stage 2. the rotational acceleration of the pinion in its bearings 3. the axial displacement of the pinion in its bearings The comparison of the two load cases in figure 7 yields the following conclusions: The sudden torque peak in the generator torque, as a result of the grid disturbance, causes a torque peak at the pinion. The level of this latter peak equals 2.5 knm, which is about 3.5 times lower than the level of the torque peak in the generator. Further experimental validation of the numerical models and a proper consideration of the damping in the drive train is required to assess the accuracy of this absolute level. This level depends furthermore on the type of coupling used in the drive train, as explained below. The sudden impact in the drive train excites moreover the 1st drive train mode of the wind turbine. As a result, various torque reversals occur during this start-up. This may lead to backlashing in the bearings (cfr. below), which should be investigated for the bearing design. Note that a proper simulation of the 1st drive train mode requires the consideration of the rotor and the tower flexibility as described in section 3.1. The grid disturbance and resulting torque variation cause the pinion to accelerate rapidly in its bearings. The acceleration peak level in this example is about 30 times higher than during the normal startup. This should also be considered with care in the design of the bearings as well as the negative acceleration, which follows rapidly after the positive acceleration peak. In the resulting variation of the acceleration, the eigenmode at 68 Hz is clearly visible, which corresponds to the deformation of the flexible coupling. Since the investigated model includes linear bearing models, the axial displacement of the pinion follows the torque variation. This implies that the displacement peaks when the torque peak occurs. Subsequently, it becomes negative. Under the assumption that the drive train is at no load conditions for a displacement value of 0 µm the change in sign for the displacement corresponds to passing the clearance at the pinion. The simulation of this so-called backlashing may be further improved by using a non-linear bearing model, including clearance.

12 3676 PROCEEDINGS OF ISMA2006 (a) Torque at the pinion of the high speed stage (b) Rotational acceleration of the pinion (high speed stage) in its bearings (c) Axial displacement of the pinion (high speed stage) in its bearings (0 µm corresponds to no load) Figure 7: Comparison of the results calculated for two transient load cases (dashed: normal start-up; solid: grid disturbance).

13 ROTATING MACHINERY:DYNAMICS 3677 The presented analyses are further elaborated by investigating the influence of the stiffness of the flexible coupling on the level of the torque and the acceleration at the pinion. This demonstrates how the multibody simulation approach can be used as an effective tool to assess the influence of design changes. Figure 8 shows the simulated torque and acceleration signals for the original coupling (A), for a coupling with a stiffness value of 10% (B) and of 1000% (C) of the original. The absolute stiffness values of the three couplings are shown in table 3, including the dimensions of a hypothetical steel shaft which has this stiffness. Coupling Stiffness Length Diameter [MNm/rad] [m] [mm] A B C Table 3: Stiffness values for the three flexible couplings used in the transient simulation. The dimensions (length and diameter) of a hypothetical steel shaft with a corresponding stiffness are included. (a) Torque at the pinion of the high speed stage (b) Rotational acceleration of the pinion (high speed stage) in its bearings Figure 8: Comparison of the simulations for three different couplings: solid: original coupling (A); dashed: lower stiffness (B); dotted: higher stiffness (C).

14 3678 PROCEEDINGS OF ISMA2006 A comparison of the simulations for the three couplings yields the following conclusions. The level of the torque peak at the pinion decreases when a coupling with a lower stiffness (B) is used. In the present example, the peak is 1.6 times lower than for the original coupling (A). On the other hand, using a coupling with a higher stiffness (C), yields a higher torque peak. In the present example, the maximum torque level is 5% higher. The maximum level of the rotational acceleration of the pinion in its bearings is for both additional couplings lower than for the original coupling. 4 Conclusions This article starts from the statement that the output of the simulations with traditional wind turbine design codes lacks insight in the dynamic behaviour of the internal drive train components. It demonstrates subsequently how the multibody simulation technique can be used to gain more insight. The particular example consists of a drive train with a single main bearing integrated in the gearbox and a DFIG. It is a three stage gearbox with one spur planetary gear stage, one helical planetary gear stage and one helical parallel gear stage. The dynamic analysis of this drive train is split up into the frequency ranges [ 0-10 Hz] and [ Hz]. For the study in the former range, a flexible multibody model with an accurate description of the rotor, the tower and the complete drive train is analysed. All eigenmodes of this model are described and those modes which have the biggest influence on the torque - the so-called drive train modes - are indicated. In the latter frequency range, the focus is limited on the local eigenmodes in the drive train. The analysed model includes a rigid body with a large inertia to represent the rotor and no additional body for the tower, since this acts as a rigid supporting structure in this frequency range. The coupling with the generator is included as a torsional spring element between the gearbox output shaft and the discrete mass of the generator. This final model of the drive train in the wind turbine has about 70 DOFs and has its first relevant eigenfrequency at 68 Hz. A frequency response analysis in the range [ Hz] for a torque excitation at the gear mesh in the high speed planetary gear stage, indicates the importance of the different eigenmodes for the torque in the drive train during this excitation. Based on the calculated FRFs, a set of eigenmodes, which can lead to amplified torque levels, is identified and, subsequently, compared with possible excitation frequencies in a Campbell diagram to identify possible drive train resonances. In addition, the frequency response analyses demonstrate how the loads in the drive train can be simulated for a sinusoidal load excitation. Finally, the investigation of two transient load cases demonstrates how a disturbance, which causes a torque variation with a high amplitude in the generator torque, yields a torque peak on the pinion of the high speed stage, high rotational acceleration levels for the bearings of the pinion and an oscillating axial displacement of the pinion in its bearings. A sensitivity analysis indicates how a flexible coupling with a lower stiffness value can reduce the amplitude of the torque peak on the pinion. This article demonstrates the simulation of a transient load case for a particular disturbance in the electricity grid. Since the accuracy of the predicted load levels in a transient analysis depend highly on the accuracy of the load excitation, it is recommended to further investigate the occurrence and the appropriate description of such excitations during realistic load cases. The most efficient solution for this problem seems to be an integration of the extended drive train model in one of the existing wind turbine design codes, since these codes contain usually most of the desired features to describe the applied loads on the wind turbine. References [1] W. D haeseleer. Energie vandaag en morgen : Beschouwingen over energievoorziening en -gebruik. Leuven : Acco, 2005.

15 ROTATING MACHINERY:DYNAMICS 3679 [2] GWEC. Global Wind Report [3] J. Peeters. Simulation of dynamica drive train loads in a wind turbine. PhD dissertation, K.U.Leuven, Department of Mechanical Engineering, Division PMA, Leuven (Heverlee), Belgium, available online: [4] E. De Vries. Trouble spots: Gearbox failures and design solutions. Renewable Energy World, 9(2):37 47, [5] LMS. DADS Revision 9.6 Documentation. LMS International, Belgium, [6] A. Kahraman. Effect of axial vibrations on the dynamics of a helical gear pair. Journal of Vibration and Acoustics, 115:33 39, [7] J. Lin and R. G. Parker. Analytical Characterization of the Unique Properties of Planetary Gear Free Vibration. Journal of Vibration and Acoustics, 121: , [8] R. R. J. Craig. Structural dynamics. John Wiley & Sons, Inc., [9] R. R. J. Craig. A review of time-domain and frequency-domain component-mode synthesis methods. International Journal of Analytical and Experimental Modal Analysis, 2(2):59 72, [10] J. D. Smith. Gears and their vibration. Marcel Dekker, New York and MacMillan, London, [11] J. Soens, J. Driesen, and R. Belmans. Interaction between Electrical Grid Phenomena and the Wind Turbine s Behaviour. Proceedings of The International Conference on Noise and Vibration Engineering (ISMA2004), pp , Leuven, Belgium, September 20-22, [12] S. Seman, J. Niiranen, S. Kanerva, and A. Arkkio. Analysis of a 1.7 MVA Doubly Fed Wind-Power Induction Generator during Power Systems Disturbances. Proceedings of the Nordic Workshop on Power and Industrial Electronics (NORPIE/2004), Trondheim, Norway, June 14-16, [13] S. Seman, S. Kanerva, J. Niiranen, and A. Arkkio. Transient Analysis of Doubly Fed Power Induction Generator Using Coupled Field-Circuit Model. Proceedings of the 16th International Conference on Electrical Machines, Krakow, Poland, September 5-8, 2004.

16 3680 PROCEEDINGS OF ISMA2006

The validation of MBS multi-megawatt gearbox models on a 13.2 MW test rig

The validation of MBS multi-megawatt gearbox models on a 13.2 MW test rig The validation of MBS multi-megawatt gearbox models on a 13.2 MW test rig Ben Marrant Wind Power Technology A brand of ZF ZFWP R&D department 1 The Presentation validation of Title, MBS Date multimegawatt

More information

Multibody modelling of shuttling excitation in spur and helical geared transmissions

Multibody modelling of shuttling excitation in spur and helical geared transmissions Multibody modelling of shuttling excitation in spur and helical geared transmissions A. Palermo 1,3, D. Mundo 1, R. Hadjit 2, P. Mas 2, W. Desmet 3 1 University of Calabria, Department of Mechanical Engineering

More information

Vibration Measurement and Noise Control in Planetary Gear Train

Vibration Measurement and Noise Control in Planetary Gear Train Vibration Measurement and Noise Control in Planetary Gear Train A.R.Mokate 1, R.R.Navthar 2 P.G. Student, Department of Mechanical Engineering, PDVVP COE, A. Nagar, Maharashtra, India 1 Assistance Professor,

More information

Drivetrain Simulation and Load Determination using SIMPACK

Drivetrain Simulation and Load Determination using SIMPACK Fakultät Maschinenwesen, Institut für Maschinenelemente und Maschinenkonstruktion, Lehrstuhl Maschinenelemente Drivetrain Simulation and Load Determination using SIMPACK SIMPACK Conference Wind and Drivetrain

More information

Experimental Verification of the Implementation of Bend-Twist Coupling in a Wind Turbine Blade

Experimental Verification of the Implementation of Bend-Twist Coupling in a Wind Turbine Blade Experimental Verification of the Implementation of Bend-Twist Coupling in a Wind Turbine Blade Authors: Marcin Luczak (LMS), Kim Branner (Risø DTU), Simone Manzato (LMS), Philipp Haselbach (Risø DTU),

More information

Dynamic characteristics of railway concrete sleepers using impact excitation techniques and model analysis

Dynamic characteristics of railway concrete sleepers using impact excitation techniques and model analysis Dynamic characteristics of railway concrete sleepers using impact excitation techniques and model analysis Akira Aikawa *, Fumihiro Urakawa *, Kazuhisa Abe **, Akira Namura * * Railway Technical Research

More information

Analysis and control of vehicle steering wheel angular vibrations

Analysis and control of vehicle steering wheel angular vibrations Analysis and control of vehicle steering wheel angular vibrations T. LANDREAU - V. GILLET Auto Chassis International Chassis Engineering Department Summary : The steering wheel vibration is analyzed through

More information

Analysis on natural characteristics of four-stage main transmission system in three-engine helicopter

Analysis on natural characteristics of four-stage main transmission system in three-engine helicopter Article ID: 18558; Draft date: 2017-06-12 23:31 Analysis on natural characteristics of four-stage main transmission system in three-engine helicopter Yuan Chen 1, Ru-peng Zhu 2, Ye-ping Xiong 3, Guang-hu

More information

Development and validation of a vibration model for a complete vehicle

Development and validation of a vibration model for a complete vehicle Development and validation of a vibration for a complete vehicle J.W.L.H. Maas DCT 27.131 External Traineeship (MW Group) Supervisors: M.Sc. O. Handrick (MW Group) Dipl.-Ing. H. Schneeweiss (MW Group)

More information

How Multibody-System Simulation Models can Support the Design of Wind Turbines

How Multibody-System Simulation Models can Support the Design of Wind Turbines Fakultät Maschinenwesen, Institut für Maschinenelemente und Maschinenkonstruktion, Lehrstuhl Maschinenelemente How Multibody-System Simulation Models can Support the Design of Wind Turbines 4 th Wind and

More information

AXLE HOUSING AND UNITIZE BEARING PACK SET MODAL CHARACTERISATION

AXLE HOUSING AND UNITIZE BEARING PACK SET MODAL CHARACTERISATION F2004F461 AXLE HOUSING AND UNITIZE BEARING PACK SET MODAL CHARACTERISATION 1 Badiola, Virginia*, 2 Pintor, Jesús María, 3 Gainza, Gorka 1 Dana Equipamientos S.A., España, 2 Universidad Pública de Navarra,

More information

Effect of Multiple Faults and Fault Severity on Gearbox Fault Detection in a Wind Turbine using Electrical Current Signals

Effect of Multiple Faults and Fault Severity on Gearbox Fault Detection in a Wind Turbine using Electrical Current Signals A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 33, 2013 Guest Editors: Enrico Zio, Piero Baraldi Copyright 2013, AIDIC Servizi S.r.l., ISBN 978-88-95608-24-2; ISSN 1974-9791 The Italian Association

More information

Estimation of Unmeasured DOF s on a Scaled Model of a Blade Structure

Estimation of Unmeasured DOF s on a Scaled Model of a Blade Structure Estimation of Unmeasured DOF s on a Scaled Model of a Blade Structure Anders Skafte 1, Rune Brincker 2 ABSTRACT This paper presents a new expansion technique which enables to predict mode shape coordinates

More information

Active Control of Sheet Motion for a Hot-Dip Galvanizing Line. Dr. Stuart J. Shelley Dr. Thomas D. Sharp Mr. Ronald C. Merkel

Active Control of Sheet Motion for a Hot-Dip Galvanizing Line. Dr. Stuart J. Shelley Dr. Thomas D. Sharp Mr. Ronald C. Merkel Active Control of Sheet Motion for a Hot-Dip Galvanizing Line Dr. Stuart J. Shelley Dr. Thomas D. Sharp Mr. Ronald C. Merkel Sheet Dynamics, Ltd. 1776 Mentor Avenue, Suite 17 Cincinnati, Ohio 45242 Active

More information

Research on vibration reduction of multiple parallel gear shafts with ISFD

Research on vibration reduction of multiple parallel gear shafts with ISFD Research on vibration reduction of multiple parallel gear shafts with ISFD Kaihua Lu 1, Lidong He 2, Wei Yan 3 Beijing Key Laboratory of Health Monitoring and Self-Recovery for High-End Mechanical Equipment,

More information

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 2.114

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 2.114 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY SIMULATION AND VIBRATION ANALYSIS OF GEAR BOX USED IN COOLING TOWER FAN K.G.Patel*, S.U.Patil, H.G.Patil D.N.Patel College of

More information

Prediction of Dynamic Factors for Helical Gears in a High-Speed Multibody Gearbox System

Prediction of Dynamic Factors for Helical Gears in a High-Speed Multibody Gearbox System Prediction of Dynamic Factors for Helical Gears in a High-Speed Multibody Gearbox System Niranjan Raghuraman, Dr. Sharad Jain and Chad Glinsky [The statements and opinions contained herein are those of

More information

Influential Criteria on the Optimization of a Gearbox, with Application to an Automatic Transmission

Influential Criteria on the Optimization of a Gearbox, with Application to an Automatic Transmission Influential Criteria on the Optimization of a Gearbox, with Application to an Automatic Transmission Peter Tenberge, Daniel Kupka and Thomas Panéro Introduction In the design of an automatic transmission

More information

CHAPTER 6 MECHANICAL SHOCK TESTS ON DIP-PCB ASSEMBLY

CHAPTER 6 MECHANICAL SHOCK TESTS ON DIP-PCB ASSEMBLY 135 CHAPTER 6 MECHANICAL SHOCK TESTS ON DIP-PCB ASSEMBLY 6.1 INTRODUCTION Shock is often defined as a rapid transfer of energy to a mechanical system, which results in a significant increase in the stress,

More information

inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering August 2000, Nice, FRANCE

inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering August 2000, Nice, FRANCE Copyright SFA - InterNoise 2000 1 inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering 27-30 August 2000, Nice, FRANCE I-INCE Classification: 7.6 ROLLING NOISE FROM

More information

MODELING SUSPENSION DAMPER MODULES USING LS-DYNA

MODELING SUSPENSION DAMPER MODULES USING LS-DYNA MODELING SUSPENSION DAMPER MODULES USING LS-DYNA Jason J. Tao Delphi Automotive Systems Energy & Chassis Systems Division 435 Cincinnati Street Dayton, OH 4548 Telephone: (937) 455-6298 E-mail: Jason.J.Tao@Delphiauto.com

More information

Mathematical Modelling and Simulation Of Semi- Active Suspension System For An 8 8 Armoured Wheeled Vehicle With 11 DOF

Mathematical Modelling and Simulation Of Semi- Active Suspension System For An 8 8 Armoured Wheeled Vehicle With 11 DOF Mathematical Modelling and Simulation Of Semi- Active Suspension System For An 8 8 Armoured Wheeled Vehicle With 11 DOF Sujithkumar M Sc C, V V Jagirdar Sc D and MW Trikande Sc G VRDE, Ahmednagar Maharashtra-414006,

More information

1874. Effect predictions of star pinion geometry phase adjustments on dynamic load sharing behaviors of differential face gear trains

1874. Effect predictions of star pinion geometry phase adjustments on dynamic load sharing behaviors of differential face gear trains 1874. Effect predictions of star pinion geometry phase adjustments on dynamic load sharing behaviors of differential face gear trains Zhengminqing Li 1, Wei Ye 2, Linlin Zhang 3, Rupeng Zhu 4 Nanjing University

More information

Study on Mechanism of Impact Noise on Steering Gear While Turning Steering Wheel in Opposite Directions

Study on Mechanism of Impact Noise on Steering Gear While Turning Steering Wheel in Opposite Directions Study on Mechanism of Impact Noise on Steering Gear While Turning Steering Wheel in Opposite Directions Jeong-Tae Kim 1 ; Jong Wha Lee 2 ; Sun Mok Lee 3 ; Taewhwi Lee 4 ; Woong-Gi Kim 5 1 Hyundai Mobis,

More information

Customer Application Examples

Customer Application Examples Customer Application Examples The New, Powerful Gearwheel Module 1 SIMPACK Usermeeting 2006 Baden-Baden 21. 22. March 2006 The New, Powerful Gearwheel Module L. Mauer INTEC GmbH Wessling Customer Application

More information

MODELS FOR THE DYNAMIC ANALYSIS OF THE SUSPENSION SYSTEM OF THE VEHICLES REAR AXLE

MODELS FOR THE DYNAMIC ANALYSIS OF THE SUSPENSION SYSTEM OF THE VEHICLES REAR AXLE MODELS FOR THE DYNAMIC ANALYSIS OF THE SUSPENSION SYSTEM OF THE VEHICLES REAR AXLE Alexandru Cătălin Transilvania University of Braşov, Product Design and Robotics Department, calex@unitbv.ro Keywords:

More information

Forced vibration frequency response for a permanent magnetic planetary gear

Forced vibration frequency response for a permanent magnetic planetary gear Forced vibration frequency response for a permanent magnetic planetary gear Xuejun Zhu 1, Xiuhong Hao 2, Minggui Qu 3 1 Hebei Provincial Key Laboratory of Parallel Robot and Mechatronic System, Yanshan

More information

HELICOPTER TAIL ROTOR ANALYSIS: EXPERIENCE IN AGUSTA WITH ADAMS

HELICOPTER TAIL ROTOR ANALYSIS: EXPERIENCE IN AGUSTA WITH ADAMS HELICOPTER TAIL ROTOR ANALYSIS: EXPERIENCE IN AGUSTA WITH ADAMS Bianchi F., Agusta Sp.a. Via G.Agusta, 520 - Cascina Costa di Samarate,Varese - Italy - e-mail: atr@agusta.it Abstract The purpose of the

More information

TURBOGENERATOR DYNAMIC ANALYSIS TO IDENTIFY CRITICAL SPEED AND VIBRATION SEVERITY

TURBOGENERATOR DYNAMIC ANALYSIS TO IDENTIFY CRITICAL SPEED AND VIBRATION SEVERITY U.P.B. Sci. Bull., Series D, Vol. 77, Iss. 3, 2015 ISSN 1454-2358 TURBOGENERATOR DYNAMIC ANALYSIS TO IDENTIFY CRITICAL SPEED AND VIBRATION SEVERITY Claudiu BISU 1, Florian ISTRATE 2, Marin ANICA 3 Vibration

More information

CRITICAL SPEED ANALYSIS FOR DUAL ROTOR SYSTEM USING FINITE ELEMENT METHOD

CRITICAL SPEED ANALYSIS FOR DUAL ROTOR SYSTEM USING FINITE ELEMENT METHOD CRITICAL SPEED ANALYSIS FOR DUAL ROTOR SYSTEM USING FINITE ELEMENT METHOD Kai Sun, Zhao Wan, Huiying Song, Shaohui Wang AVIC Commercial Aircraft Engine Co. Ltd, 3998 South Lianhua Road, 201108 Shanghai,

More information

RELIABILITY IMPROVEMENT OF ACCESSORY GEARBOX BEVEL DRIVES Kozharinov Egor* *CIAM

RELIABILITY IMPROVEMENT OF ACCESSORY GEARBOX BEVEL DRIVES Kozharinov Egor* *CIAM RELIABILITY IMPROVEMENT OF ACCESSORY GEARBOX BEVEL DRIVES Kozharinov Egor* *CIAM egor@ciam.ru Keywords: Bevel gears, accessory drives, resonance oscillations, Coulomb friction damping Abstract Bevel gear

More information

Effects of Large Bending Deflections on Blade Flutter Limits. UpWind Deliverable D2.3. Bjarne Skovmose Kallesøe Morten Hartvig Hansen.

Effects of Large Bending Deflections on Blade Flutter Limits. UpWind Deliverable D2.3. Bjarne Skovmose Kallesøe Morten Hartvig Hansen. Effects of Large Bending Deflections on Blade Flutter Limits UpWind Deliverable D2.3 Bjarne Skovmose Kallesøe Morten Hartvig Hansen Risø R 1642(EN) Risø National Laboratory for Sustainable Energy Technical

More information

Multiphysics Modeling of Railway Pneumatic Suspensions

Multiphysics Modeling of Railway Pneumatic Suspensions SIMPACK User Meeting Salzburg, Austria, 18 th and 19 th May 2011 Multiphysics Modeling of Railway Pneumatic Suspensions Nicolas Docquier Université catholique de Louvain, Belgium Institute of Mechanics,

More information

A 3D FINITE ELEMENT MODELING OF HAMMER TEST FOR TRACK PARAMETER IDENTIFICATION

A 3D FINITE ELEMENT MODELING OF HAMMER TEST FOR TRACK PARAMETER IDENTIFICATION A 3D FINITE ELEMENT MODELING OF HAMMER TEST FOR TRACK PARAMETER IDENTIFICATION Oregui, M. 1, Li, Z. 1, Dollevoet R. 2, Moraal, J. 1 1 Delft University of Technology, Section of Road and Railway Engineering

More information

Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing

Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing Gopali S Lamani 1, Prof: S.R.Basavaraddi 2, Assistant Professor, Department of Mechanical Engineering, JSPM NTC RSSOER,India1 Professor,

More information

On the prediction of rail cross mobility and track decay rates using Finite Element Models

On the prediction of rail cross mobility and track decay rates using Finite Element Models On the prediction of rail cross mobility and track decay rates using Finite Element Models Benjamin Betgen Vibratec, 28 Chemin du Petit Bois, 69130 Ecully, France. Giacomo Squicciarini, David J. Thompson

More information

STIFFNESS CHARACTERISTICS OF MAIN BEARINGS FOUNDATION OF MARINE ENGINE

STIFFNESS CHARACTERISTICS OF MAIN BEARINGS FOUNDATION OF MARINE ENGINE Journal of KONES Powertrain and Transport, Vol. 23, No. 1 2016 STIFFNESS CHARACTERISTICS OF MAIN BEARINGS FOUNDATION OF MARINE ENGINE Lech Murawski Gdynia Maritime University, Faculty of Marine Engineering

More information

CASE STUDY OF ASSEMBLY ERRORS INFLUENCE ON STRESS DISTRIBUTION IN SPUR GEAR TRAIN

CASE STUDY OF ASSEMBLY ERRORS INFLUENCE ON STRESS DISTRIBUTION IN SPUR GEAR TRAIN Proceedings of the 7th International Conference on Mechanics and Materials in Design Albufeira/Portugal 11-15 June 2017. Editors J.F. Silva Gomes and S.A. Meguid. Publ. INEGI/FEUP (2017) PAPER REF: 6564

More information

Balancing and over-speed testing of flexible rotors

Balancing and over-speed testing of flexible rotors Balancing and over-speed testing of flexible rotors Installations for low- and high-speed balancing and for over-speed testing HS 16 - HS 34 Application Balancing of flexible rotors from turbo-machinery

More information

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4

More information

Analysis of Eclipse Drive Train for Wind Turbine Transmission System

Analysis of Eclipse Drive Train for Wind Turbine Transmission System ISSN 2395-1621 Analysis of Eclipse Drive Train for Wind Turbine Transmission System #1 P.A. Katre, #2 S.G. Ganiger 1 pankaj12345katre@gmail.com 2 somu.ganiger@gmail.com #1 Department of Mechanical Engineering,

More information

ENTWICKLUNG DIESELMOTOREN

ENTWICKLUNG DIESELMOTOREN ENTWICKLUNG DIESELMOTOREN BMW Steyr Diesel Engine Development Center MULTIBODY AND STRUCTURAL DYNAMIC SIMULATIONS IN THE DEVELOPMENT OF NEW BMW 3- AND 4-CYLINDER DIESEL ENGINES Dr. Stefan Reichl, Dr. Martin

More information

A STUDY OF THE CENTRIFUGAL COMPRESSOR DISCHARGE PIPELINE CONSTRAINED OSCILLATION. KIRILL SOLODYANKIN*, JIŘÍ BĚHAL ČKD KOMPRESORY, a.s.

A STUDY OF THE CENTRIFUGAL COMPRESSOR DISCHARGE PIPELINE CONSTRAINED OSCILLATION. KIRILL SOLODYANKIN*, JIŘÍ BĚHAL ČKD KOMPRESORY, a.s. A STUDY OF THE CENTRIFUGAL COMPRESSOR DISCHARGE PIPELINE CONSTRAINED OSCILLATION KIRILL SOLODYANKIN*, JIŘÍ BĚHAL ČKD KOMPRESORY, a.s. Abstract: The paper presents a solution of a pipeline constrained oscillation

More information

ME scope Application Note 29 FEA Model Updating of an Aluminum Plate

ME scope Application Note 29 FEA Model Updating of an Aluminum Plate ME scope Application Note 29 FEA Model Updating of an Aluminum Plate NOTE: You must have a package with the VES-4500 Multi-Reference Modal Analysis and VES-8000 FEA Model Updating options enabled to reproduce

More information

Parameter optimisation design for a six-dof heavy duty vehicle seat suspension

Parameter optimisation design for a six-dof heavy duty vehicle seat suspension 11 th World Congress on Structural and Multidisciplinary Optimisation 07 th -12 th, June 2015, Sydney Australia Parameter optimisation design for a six-dof heavy duty vehicle seat suspension Donghong Ning,

More information

THE LONGITUDINAL VIBRATION OF COMPOSITE DRIVE SHAFT

THE LONGITUDINAL VIBRATION OF COMPOSITE DRIVE SHAFT THE LONGITUDINAL VIBRATION OF COMPOSITE DRIVE SHAFT Tongtong Zhang, Yongsheng Li, Weibo Wang National Key Laboratory on Ship Vibration and Noise, China Ship Scientific Research Centre, Wuxi, China email:

More information

STRESS AND VIBRATION ANALYSIS OF A GAS TURBINE BLADE WITH A COTTAGE-ROOF FRICTION DAMPER USING FINITE ELEMENT METHOD

STRESS AND VIBRATION ANALYSIS OF A GAS TURBINE BLADE WITH A COTTAGE-ROOF FRICTION DAMPER USING FINITE ELEMENT METHOD STRESS AND VIBRATION ANALYSIS OF A GAS TURBINE BLADE WITH A COTTAGE-ROOF FRICTION DAMPER USING FINITE ELEMENT METHOD S. Narasimha 1* G. Venkata Rao 2 and S. Ramakrishna 1 1 Dept. of Mechanical Engineering,

More information

Development of Rattle Noise Analysis Technology for Column Type Electric Power Steering Systems

Development of Rattle Noise Analysis Technology for Column Type Electric Power Steering Systems TECHNICAL REPORT Development of Rattle Noise Analysis Technology for Column Type Electric Power Steering Systems S. NISHIMURA S. ABE The backlash adjustment mechanism for reduction gears adopted in electric

More information

558. Dynamics of loadings acting on coupling device of accelerating auto-train

558. Dynamics of loadings acting on coupling device of accelerating auto-train 558. Dynamics of loadings acting on coupling device of accelerating auto-train A. Keršys, N. Keršien Kaunas Univerity of Technology, Department of Transport Engineering, Kęstučio 7, 44 Kaunas, Lithuania.

More information

Effects of Boundary Conditions on Vibration Characteristics of Planetary Ring Gear

Effects of Boundary Conditions on Vibration Characteristics of Planetary Ring Gear The 14th IFToMM World Congress, Taipei, Taiwan, October 25-3, 215 DOI Number: 1.6567/IFToMM.14TH.WC.OS6.31 Effects of Boundary Conditions on Vibration Characteristics of Planetary Ring Gear Jun Zhang 1

More information

Design of Damping Base and Dynamic Analysis of Whole Vehicle Transportation based on Filtered White-Noise GongXue Zhang1,a and Ning Chen2,b,*

Design of Damping Base and Dynamic Analysis of Whole Vehicle Transportation based on Filtered White-Noise GongXue Zhang1,a and Ning Chen2,b,* Advances in Engineering Research (AER), volume 07 Global Conference on Mechanics and Civil Engineering (GCMCE 07) Design of Damping Base and Dynamic Analysis of Whole Vehicle Transportation based on Filtered

More information

ELECTROMECHANICAL OPTIMIZATION AGAINST TORSIONAL VIBRATIONS IN O&G ELECTRIFIED TRAINS MICHELE GUIDI [GE O&G] ALESSANDRO PESCIONI [GE O&G]

ELECTROMECHANICAL OPTIMIZATION AGAINST TORSIONAL VIBRATIONS IN O&G ELECTRIFIED TRAINS MICHELE GUIDI [GE O&G] ALESSANDRO PESCIONI [GE O&G] ELECTROMECHANICAL OPTIMIZATION AGAINST TORSIONAL VIBRATIONS IN O&G ELECTRIFIED TRAINS MICHELE GUIDI [GE O&G] ALESSANDRO PESCIONI [GE O&G] Topics INTRODUCTION - Mechanical vibrations in electrified trains

More information

Experimental Analyses of Vibration and Noise of Faulted Planetary Gearbox

Experimental Analyses of Vibration and Noise of Faulted Planetary Gearbox Experimental Analyses of Vibration and Noise of Faulted Planetary Gearbox Zhuang Li McNeese State University, USA e-mail: zli@mcneese.edu ABSTRACT Epicyclic gear trains are widely used in various industrial

More information

Modeling of 17-DOF Tractor Semi- Trailer Vehicle

Modeling of 17-DOF Tractor Semi- Trailer Vehicle ISSN 2395-1621 Modeling of 17-DOF Tractor Semi- Trailer Vehicle # S. B. Walhekar, #2 D. H. Burande 1 sumitwalhekar@gmail.com 2 dhburande.scoe@sinhgad.edu #12 Mechanical Engineering Department, S.P. Pune

More information

Structural Dynamic Behaviour of Tyres

Structural Dynamic Behaviour of Tyres XIX CNIM 15-16/11 Castellón Structural Dynamic Behaviour of Tyres Paul Sas Noise & Vibration Engineering Research Group KU.Leuven, Dept. Mechanical Engineering, Div. PMA Road traffic noise Vehicle noise:

More information

Procedia Engineering 00 (2009) Mountain bike wheel endurance testing and modeling. Robin C. Redfield a,*, Cory Sutela b

Procedia Engineering 00 (2009) Mountain bike wheel endurance testing and modeling. Robin C. Redfield a,*, Cory Sutela b Procedia Engineering (29) Procedia Engineering www.elsevier.com/locate/procedia 9 th Conference of the International Sports Engineering Association (ISEA) Mountain bike wheel endurance testing and modeling

More information

White Paper. Stator Coupling Model Analysis By Johan Ihsan Mahmood Motion Control Products Division, Avago Technologies. Abstract. 1.

White Paper. Stator Coupling Model Analysis By Johan Ihsan Mahmood Motion Control Products Division, Avago Technologies. Abstract. 1. Stator Coupling Model Analysis By Johan Ihsan Mahmood Motion Control Products Division, Avago Technologies White Paper Abstract In this study, finite element analysis was used to optimize the design of

More information

Passive Vibration Reduction with Silicone Springs and Dynamic Absorber

Passive Vibration Reduction with Silicone Springs and Dynamic Absorber Available online at www.sciencedirect.com Physics Procedia 19 (2011 ) 431 435 International Conference on Optics in Precision Engineering and Nanotechnology 2011 Passive Vibration Reduction with Silicone

More information

Siemens PLM Software develops advanced testing methodologies to determine force distribution and visualize body deformation during vehicle handling.

Siemens PLM Software develops advanced testing methodologies to determine force distribution and visualize body deformation during vehicle handling. Automotive and transportation Product LMS LMS Engineering helps uncover the complex interaction between body flexibility and vehicle handling performance Business challenges Gain insight into the relationship

More information

IMPACT2014 & SMASH Vibration propagation and damping tests V0A-V0C: Testing and simulation

IMPACT2014 & SMASH Vibration propagation and damping tests V0A-V0C: Testing and simulation IMPACT2014 & SMASH Vibration propagation and damping tests V0A-V0C: Testing and simulation SAFIR2014 Final seminar, 20.3.2015 Kim Calonius, Seppo Aatola, Ilkka Hakola, Matti Halonen, Arja Saarenheimo,

More information

Latest Results in the CVT Development

Latest Results in the CVT Development 5 Latest Results in the CVT Development Norbert Indlekofer Uwe Wagner Alexander Fidlin André Teubert 5 LuK SYMPOSIUM 2002 63 Introduction The main requirements of the drive trains for the future are defined:

More information

Vibration Analysis of an All-Terrain Vehicle

Vibration Analysis of an All-Terrain Vehicle Vibration Analysis of an All-Terrain Vehicle Neeraj Patel, Tarun Gupta B.Tech, Department of Mechanical Engineering, Maulana Azad National Institute of Technology, Bhopal, India. Abstract - Good NVH is

More information

A STUDY ON JACK-UP GEARBOX DESIGN FOR DRILLSHIPS

A STUDY ON JACK-UP GEARBOX DESIGN FOR DRILLSHIPS International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 6, June 2018, pp. 948 959, Article ID: IJMET_09_06_107 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=6

More information

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating

More information

Switch design optimisation: Optimisation of track gauge and track stiffness

Switch design optimisation: Optimisation of track gauge and track stiffness 1 Switch design optimisation: Optimisation of track gauge and track stiffness Elias Kassa Professor, Phd Department of Civil and Transport Engineering, NTNU Trondheim, Norway E-mail: elias.kassa@ntnu.no

More information

Vehicle Dynamic Simulation Using A Non-Linear Finite Element Simulation Program (LS-DYNA)

Vehicle Dynamic Simulation Using A Non-Linear Finite Element Simulation Program (LS-DYNA) Vehicle Dynamic Simulation Using A Non-Linear Finite Element Simulation Program (LS-DYNA) G. S. Choi and H. K. Min Kia Motors Technical Center 3-61 INTRODUCTION The reason manufacturers invest their time

More information

ME scope Application Note 24 Choosing Reference DOFs for a Modal Test

ME scope Application Note 24 Choosing Reference DOFs for a Modal Test ME scope Application Note 24 Choosing Reference DOFs for a Modal Test The steps in this Application Note can be duplicated using any ME'scope Package that includes the VES-3600 Advanced Signal Processing

More information

Design Validation of an Integrated Transmission System

Design Validation of an Integrated Transmission System Design Validation of an Integrated Transmission System Vikas Manjrekar 1, S Shamasundar 2*, Samarth Shrivastava 3 1 Executive Vice President, R&D& Strategic Sourcing, AVTEC Ltd, Pithampur, MP. Email: vikas.manjrekar@avtec.in

More information

KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD

KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD Jurnal Mekanikal June 2014, No 37, 16-25 KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD Mohd Awaluddin A Rahman and Afandi Dzakaria Faculty of Mechanical Engineering, Universiti

More information

ANTI-BACKLASH GEAR TRAIN INVESTIGATION. Zengxin Gao, Jani Tähtinen

ANTI-BACKLASH GEAR TRAIN INVESTIGATION. Zengxin Gao, Jani Tähtinen Zengxin Gao, Jani Tähtinen Wärtsilä Finland Oy Järvikatu 2-4, P.O. Box 244 FI-65101 Vaasa zengxin.gao@wartsila.com jani.tahtinen@wartsila.com 1 INTRODUCTION This paper is a continuation of study on Wärtsilä

More information

Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers

Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers U. Bin-Nun FLIR Systems Inc. Boston, MA 01862 ABSTRACT Cryocooler self induced vibration is a major consideration in the design of IR

More information

Alan R. Klembczyk, Chief Engineer Taylor Devices, Inc. North Tonawanda, NY

Alan R. Klembczyk, Chief Engineer Taylor Devices, Inc. North Tonawanda, NY SIMULATION, DEVELOPMENT, AND FIELD MEASUREMENT VALIDATION OF AN ISOLATION SYSTEM FOR A NEW ELECTRONICS CABINET IN THE SPACE SHUTTLE LAUNCH ENVIRONMENT WITHIN THE MOBILE LAUNCH PLATFORM Alan R. Klembczyk,

More information

Investigations into engine transient response due to internal and external dynamic excitations

Investigations into engine transient response due to internal and external dynamic excitations Investigations into engine transient response due to internal and external dynamic excitations Moreno Barragán J.A. MTU Aero Engines GmbH, Engine Dynamics, Dachauer Strasse 665, D-80995 Munich, Germany

More information

Vehicle functional design from PSA in-house software to AMESim standard library with increased modularity

Vehicle functional design from PSA in-house software to AMESim standard library with increased modularity Vehicle functional design from PSA in-house software to AMESim standard library with increased modularity Benoit PARMENTIER, Frederic MONNERIE (PSA) Marc ALIRAND, Julien LAGNIER (LMS) Vehicle Dynamics

More information

CHAPTER 3 TRANSIENT STABILITY ENHANCEMENT IN A REAL TIME SYSTEM USING STATCOM

CHAPTER 3 TRANSIENT STABILITY ENHANCEMENT IN A REAL TIME SYSTEM USING STATCOM 61 CHAPTER 3 TRANSIENT STABILITY ENHANCEMENT IN A REAL TIME SYSTEM USING STATCOM 3.1 INTRODUCTION The modeling of the real time system with STATCOM using MiPower simulation software is presented in this

More information

Vibration Analysis of Gear Transmission System in Electric Vehicle

Vibration Analysis of Gear Transmission System in Electric Vehicle Advanced Materials Research Online: 0-0- ISSN: 66-8985, Vols. 99-00, pp 89-83 doi:0.408/www.scientific.net/amr.99-00.89 0 Trans Tech Publications, Switzerland Vibration Analysis of Gear Transmission System

More information

Optimum combined pitch and trailing edge flap control

Optimum combined pitch and trailing edge flap control Optimum combined pitch and trailing edge flap control Lars Christian Henriksen, DTU Wind Energy Leonardo Bergami, DTU Wind Energy Peter Bjørn Andersen, DTU Wind Energy Session 5.3 Aerodynamics Danish Wind

More information

inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering August 2000, Nice, FRANCE

inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering August 2000, Nice, FRANCE Copyright SFA - InterNoise 2000 1 inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering 27-30 August 2000, Nice, FRANCE I-INCE Classification: 0.0 EFFECTS OF TRANSVERSE

More information

Generator Speed Control Utilizing Hydraulic Displacement Units in a Constant Pressure Grid for Mobile Electrical Systems

Generator Speed Control Utilizing Hydraulic Displacement Units in a Constant Pressure Grid for Mobile Electrical Systems Group 10 - Mobile Hydraulics Paper 10-5 199 Generator Speed Control Utilizing Hydraulic Displacement Units in a Constant Pressure Grid for Mobile Electrical Systems Thomas Dötschel, Michael Deeken, Dr.-Ing.

More information

FAULT ANALYSIS OF AN ISLANDED MICRO-GRID WITH DOUBLY FED INDUCTION GENERATOR BASED WIND TURBINE

FAULT ANALYSIS OF AN ISLANDED MICRO-GRID WITH DOUBLY FED INDUCTION GENERATOR BASED WIND TURBINE FAULT ANALYSIS OF AN ISLANDED MICRO-GRID WITH DOUBLY FED INDUCTION GENERATOR BASED WIND TURBINE Yunqi WANG, B.T. PHUNG, Jayashri RAVISHANKAR School of Electrical Engineering and Telecommunications The

More information

Influence of Parameter Variations on System Identification of Full Car Model

Influence of Parameter Variations on System Identification of Full Car Model Influence of Parameter Variations on System Identification of Full Car Model Fengchun Sun, an Cui Abstract The car model is used extensively in the system identification of a vehicle suspension system

More information

Active Suspensions For Tracked Vehicles

Active Suspensions For Tracked Vehicles Active Suspensions For Tracked Vehicles Y.G.Srinivasa, P. V. Manivannan 1, Rajesh K 2 and Sanjay goyal 2 Precision Engineering and Instrumentation Lab Indian Institute of Technology Madras Chennai 1 PEIL

More information

NUMERICAL ANALYSIS OF IMPACT BETWEEN SHUNTING LOCOMOTIVE AND SELECTED ROAD VEHICLE

NUMERICAL ANALYSIS OF IMPACT BETWEEN SHUNTING LOCOMOTIVE AND SELECTED ROAD VEHICLE Journal of KONES Powertrain and Transport, Vol. 21, No. 4 2014 ISSN: 1231-4005 e-issn: 2354-0133 ICID: 1130437 DOI: 10.5604/12314005.1130437 NUMERICAL ANALYSIS OF IMPACT BETWEEN SHUNTING LOCOMOTIVE AND

More information

Simulating Rotary Draw Bending and Tube Hydroforming

Simulating Rotary Draw Bending and Tube Hydroforming Abstract: Simulating Rotary Draw Bending and Tube Hydroforming Dilip K Mahanty, Narendran M. Balan Engineering Services Group, Tata Consultancy Services Tube hydroforming is currently an active area of

More information

Noise Reduction of Accumulators for R410A Rotary Compressors

Noise Reduction of Accumulators for R410A Rotary Compressors Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2008 Noise Reduction of Accumulators for R410A Rotary Compressors Ling Li Guangdong Meizhi

More information

VIBRATIONAL ANALYSIS OF A MULTIBODY VIRTUAL DUMMY FOR CAR AND MOTORCYCLE USERS

VIBRATIONAL ANALYSIS OF A MULTIBODY VIRTUAL DUMMY FOR CAR AND MOTORCYCLE USERS VIBRATIONAL ANALYSIS OF A MULTIBODY VIRTUAL DUMMY FOR CAR AND MOTORCYCLE USERS Nicola Cofelice*, Roberto Zanni, Davide Locatelli, Alessandro Toso, David Moreno Giner, Jian Kang, Stijn Donders Agenda 1

More information

The X-Rotor Offshore Wind Turbine Concept

The X-Rotor Offshore Wind Turbine Concept DeepWind 2019 The X-Rotor Offshore Wind Turbine Concept Bill Leithead Arthur Camciuc, Abbas Kazemi Amiri and James Carroll University of Strathclyde Outline 1. X-Rotor Concept 2. X- Rotor Potential Benefits

More information

Modeling tire vibrations in ABS-braking

Modeling tire vibrations in ABS-braking Modeling tire vibrations in ABS-braking Ari Tuononen Aalto University Lassi Hartikainen, Frank Petry, Stephan Westermann Goodyear S.A. Tag des Fahrwerks 8. Oktober 2012 Contents 1. Introduction 2. Review

More information

Modeling and Vibration Analysis of a Drum type Washing Machine

Modeling and Vibration Analysis of a Drum type Washing Machine Modeling and Vibration Analysis of a Drum type Washing Machine Takayuki KOIZUMI, Nobutaka TSUJIUCHI, Yutaka NISHIMURA Department of Engineering, Doshisha University, 1-3, Tataramiyakodani, Kyotanabe, Kyoto,

More information

VOLUME 9, FIRST ISSUE

VOLUME 9, FIRST ISSUE Editor INTEC GmbH, Argelsrieder Feld 13, 82234 Wessling, Germany VOLUME 9, FIRST ISSUE JULY 2005» CUSTOMER APPLICATION...01 Gearshift-Comfort Oriented Transmission and Drive Train Simulation at BMW» SOFTWARE...

More information

Validation of a FAST Model of the Statoil- Hywind Demo Floating Wind Turbine

Validation of a FAST Model of the Statoil- Hywind Demo Floating Wind Turbine Validation of a FAST Model of the Statoil- Hywind Demo Floating Wind Turbine EERA DeepWind 2016 20-22 January, 2016 Frederick Driscoll, NREL Jason Jonkman, NREL Amy Robertson, NREL Senu Sirnivas, NREL

More information

Gearbox Fault Detection

Gearbox Fault Detection Gearbox Fault Detection At the University of Iowa, detecting wind turbine gearbox faults based on vibration acceleration data provided by NREL is augmented by data mining techniques. By Andrew Kusiak and

More information

TNO Science and Industry P.O. Box 756, 5700 AT Helmond, The Netherlands Honda R&D Co., Ltd.

TNO Science and Industry P.O. Box 756, 5700 AT Helmond, The Netherlands   Honda R&D Co., Ltd. Proceedings, Bicycle and Motorcycle Dynamics 2010 Symposium on the Dynamics and Control of Single Track Vehicles, 20-22 October 2010, Delft, The Netherlands Application of the rigid ring model for simulating

More information

2. Write the expression for estimation of the natural frequency of free torsional vibration of a shaft. (N/D 15)

2. Write the expression for estimation of the natural frequency of free torsional vibration of a shaft. (N/D 15) ME 6505 DYNAMICS OF MACHINES Fifth Semester Mechanical Engineering (Regulations 2013) Unit III PART A 1. Write the mathematical expression for a free vibration system with viscous damping. (N/D 15) Viscous

More information

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Vikas Kumar Agarwal Deputy Manager Mahindra Two Wheelers Ltd. MIDC Chinchwad Pune 411019 India Abbreviations:

More information

Development of analytical process to reduce side load in strut-type suspension

Development of analytical process to reduce side load in strut-type suspension Journal of Mechanical Science and Technology 24 (21) 351~356 www.springerlink.com/content/1738-494x DOI 1.7/s1226-9-113-z Development of analytical process to reduce side load in strut-type suspension

More information

PROGRESS IN QUALITY ASSESSMENT OF CONVEYOR IDLERS

PROGRESS IN QUALITY ASSESSMENT OF CONVEYOR IDLERS PROGRESS IN QUALITY ASSESSMENT OF CONVEYOR IDLERS W. Bartelmus and W. Sawicki Wroc³aw University of Technology Faculty of Mining Machinery Systems Division Wroc³aw Poland Abstract: The paper deals with

More information

VALMONT MITIGATOR TR1

VALMONT MITIGATOR TR1 VALMONT MITIGATOR TR1 Research Verification of the Valmont TR1 Damper Performance MITIGATOR TR1 VIBRATION DAMPER The Valmont TR1 damper has been specifically designed using vibration theory and innovative

More information

ATLAS Principle to Product

ATLAS Principle to Product ATLAS Principle to Product SUPERGEN 26th May 2016 Wind and tidal energy control experts SgurrControl Experts in wind and tidal energy control Engineering organisation providing control solutions to wind

More information

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS 8 FASCICLE VIII, 8 (XIV), ISSN 11-459 Paper presented at Bucharest, Romania ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS Laurentia ANDREI 1), Gabriel ANDREI 1) T, Douglas

More information