KM-1300MAH KM-1300MWH KM-1300MRH

Transcription

1 71187 ISSUED: JUNE 24, 2001 REVISED: JULY 29, 2003 TM HOSHIZAKI MODULAR CRESCENT CUBER KM-1300MAH KM-1300MWH KM-1300MRH S LIST

2 KM-1300MAH April 2001 KM-1300MWH June 2001 KM-1300MRH April

3 MATERIAL ABBREVIATIONS HA ALUMINUM AL = Aluminum COPPER CU = Copper PLASTIC ABS = Acrylonitritrile -butadiene - styrene AC = Polyacetal EVA = Ethylene vinyl acetate PA = Polyamide = Nylon PC = Polycarbonate PE = Polyethylene PES = Polyester PETP = Polyethylene terephthalate = Tetlon PP = Polypropylene PS = Polystyrene PTFE = Polytetrafluoroethylene = Teflon PUR = Polyurethane PVC = Polyvinyl chloride RUBBER VN = Vinyl Nitrile EPDM = EP rubber NBR = Nitrile butadiene rubber NR = Natural rubber NP = Neoprene SI.R = Silicone rubber SY.R = Synthetic rubber EPH = Epichlorohydrin STEEL G.S = Galvanized steel S.S = Stainless steel PS = Plated steel PAS = Primed steel Ex.1 K-0 AUXILIARY CODE Parts are the same as in the preceding (Note) - = Part deleted. year. x = Part deleted and replaced "K" is the tenth in alphabetical order with "I" by "o" (interchangeable) skipped. So, "K" indicates "2000". part. Ex.2 o = New part for "x" in the "L" is the next in alphabetical same auxiliary code. order. So, "L" indicates "2001". Ex.3 L-1 Each time a part is changed non-interchangeably in a year, this number advances. 3

4 KM-1300MAH A. ICE CUBER ASSEMBLY 4

5 : KM-1300MAH TITLE: A. ICE CUBER ASSEMBLY REQUIRED B REFRIGERATION CIRCUIT - 1A0462A01 1 C WATER CIRCUIT HS A0094A04 1 D CONTROL BOX ASSEMBLY - 2A2287A01 1 T2 SCREW 4X8 7P E LABEL LOCATION - 2A2167A EVAPORATOR CASE - 1A0602G CONTROL BOX COVER GS 3A T2 SCREW 4X8 7P FRAME (F) T2 SCREW 4X8 7P SQUARE WASHER BRASS SCREW - GROUNDING BRASS BUSHING SR JUNCTION BOX COVER GS T2 SCREW 4X8 7P BUSHING FOAM SEAL - 4A0661L BARRIER - 3A T2 SCREW 4X8 7P WIRE SADDLE - 4A WIRE SADDLE - 4A TOP INSULATION ABS, PE G FRONT INSULATION ABS, PE G SIDE PANEL (R) SS 2A2165G TOP PANEL 3A1941A01, SS 2A GASKET 3A1941A01, PVC WIRE SADDLE - 4A LOUVER (A) ABS 1A

6 : KM-1300MAH TITLE: A. ICE CUBER ASSEMBLY REQUIRED 20 PUSH RETAINER - 4A AIR FILTER (A) ABS 2A2062G SPACER PE FT SCREW SS, 4X10 7F BULB HOLDER G BULB HOLDER FRONT PANEL SS 2A TRUSS HEAD SCREW 4X8, SS 7C GASKET L=762 4A0808L02 1 6

7 KM-1300MWH A. ICE CUBER ASSEMBLY 7

8 : KM-1300MWH TITLE: A. ICE CUBER ASSEMBLY REQUIRED B REFRIGERATION CIRCUIT - 1A0463A01 1 C WATER CIRCUIT HS A0094A04 1 D CONTROL BOX ASSEMBLY - 2A2287A01 1 T2 SCREW 4X8 7P E LABEL LOCATION - 2A2168A EVAP. CASE HS A0602G CONTROL BOX COVER GS 3A T2 SCREW 4X8 7P SQUARE WASHER BRASS SCREW - GROUNDING BRASS BUSHING SR JUNCTION BOX COVER GS T2 SCREW 4X8 7P FRAME (F) GS T2 SCREW 4X8 7P TOP PANEL (3A1941A01), SS 2A GASKET PVC WIRE SADDLE VWS4274-C 4A WIRE SADDLE VWS4218-C 4A TOP INSULATION ABS, PE G FRONT INSULATION ABS,PE G SIDE PANEL (R) SS 2A2165G FRONT PANEL (A) SS 2A TRUSS HEAD SCREW 4X8, SS 7C BARRIER GS 3A T2 SCREW 4X8 7P WIRE SADDLE VWS42105-C 4A WIRE SADDLE VWS4238-C 4A BULB HOLDER SS G BULB HOLDER ABS

9 : KM-1300MWH TITLE: A. ICE CUBER ASSEMBLY REQUIRED 21 SPACER PE FT SCREW 4X10, SS 7F BUSHING EPDM GASKET L=762 4A0808L02 1 9

10 KM-1300MRH A. ICE CUBER ASSEMBLY 10

11 : KM-1300MRH TITLE: A. ICE CUBER ASSEMBLY REQUIRED B REFRIGERATION CIRCUIT - 1A0464A01 1 C WATER CIRCUIT - 1A0094A04 1 D CONTROL BOX ASSEMBLY - 2A2287A01 1 T2 SCREW 4X8 7P E LABEL LOCATION - 2A2169A EVAP. CASE - 1A0602G CONTROL BOX COVER GS 3A T2 SCREW 4X8 7P FRAME (F) GS T2 SCREW 4X8 7P SQUARE WASHER BRASS SCREW - GROUNDING BRASS BUSHING SR JUNCTION BOX COVER GS T2 SCREW 4X8 7P SPACER PE FT SCREW 4X10, SS 7F BUSHING TOP PANEL (3A1941A01), SS 2A GASKET PVC WIRE SADDLE VWS4274-C 4A TOP INSULATION ABS, PE G FRONT INSULATION ABS,PE G SIDE PANEL (R) SS 2A2165G FRONT PANEL (A) SS 2A TRUSS HEAD SCREW 4X8, SS 7C WIRE SADDLE VWS4218-C 4A BARRIER GS 3A T2 SCREW 4X8 7P WIRE SADDLE VWS42105-C 4A

12 : KM-1300MRH TITLE: A. ICE CUBER ASSEMBLY REQUIRED 20 BUSHING SR BULB HOLDER SS G BULB HOLDER ABS WIRE SADDLE VWS4238-C 4A GASKET L=762 4A0808L

13 KM-1300MAH B. REFRIGERATION CIRCUIT 1/2 13

14 KM-1300MAH B. REFRIGERATION CIRCUIT 2/2 14

15 : KM-1300MAH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 1 CONDENSER T2 SCREW 4X8 7P SHROUD GS G T2 SCREW 4X8 7P TRUSS HEAD SCREW 5X8 7C COMPRESSOR CS14K6E-PFV 4A BOLT 8x GROMMET SPACER FAN MOTOR BRACKET GS 2A HEX HEAD BOLT W/WASHER (LF) 5X10 7B FRAME (C) - 3A T2 SCREW 4X8 7P FAN MOTOR U90B1, SELF-LOCKING NUT No N21I CAPACITOR 5MFD, 250V T2 SCREW 4X8 7P FAN BLADE AD10CW DRIER CW-0325-S 4A ENDCAP - 4A1413F DRIER BRACKET - 4A T2 SCREW 4X8 7P EXPANSION VALVE HFE-10NHD-2 4A EXP. VALVE COVER PE FOAM 3A EVAPORATOR G TRUSS HEAD SCREW SS, 4X8 7C T2 SCREW SS, 4X8 7P

16 : KM-1300MAH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 28 THERMISTOR HOLDER - THERMISTOR COPPER INSULATION - THERMISTOR PE FOAM TIE CV BARRIER (B) GS T2 SCREW 4X8 7P FRAME - 3A0350G FT SCREW SS, 4X8 7F T2 SCREW 4X8 7P PRESSURE SWITCH ACB-1UB PRESSURE SWITCH BRACKET GS T2 SCREW 4X8 7P HOT GAS VALVE BRACKET GS T2 SCREW 4X8 7P LINE VALVE BRACKET GS 4A T2 SCREW 4X8 7P VALVE BODY COIL - VALVE ABS-25-1-HD BOLT 4x F TRUSS HEAD SCREW 4X8 7C COPPER TUBE (A) HIGH SIDE COPPER 2A1663G COPPER TUBE (B) HIGH SIDE COPPER 2A1665G COPPER TUBE (C) HIGH SIDE COPPER 3A COPPER TUBE LINE VALVE COPPER 4A HEAT EXCHANGER - 1A0479G COPPER TUBE (L) LOW SIDE COPPER 2A1666G COPPER TUBE (R) LOW SIDE COPPER 2A1667G

17 : KM-1300MAH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 55 COPPER TUBE - HOT GAS COPPER 3A0213G CHECK VALVE SKC A STRAINER COPPER TUBE ACCESS VALVE COPPER 3A1518G ACCESS VALVE HOLDER/EXP. VALVE 3/8-3A CLAMP CABLE TIE CV INSULATED RUBBER TUBE G INSULATION HOLDER - 3A T2 SCREW SS, 4X8 7P INSULATION INSULATION TUBE L= CLAMP - 4A

18 KM-1300MWH B. REFRIGERATION CIRCUIT 1/2 18

19 KM-1300MWH B. REFRIGERATION CIRCUIT 2/2 19

20 : KM-1300MWH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 1 REAR PANEL - 3A1485G FT SCREW SS, 4X8 7F T2 SCREW 4X8 7P FRAME - 3A0350G FT SCREW SS, 4X8 7F T2 SCREW 4X8 7P COMPRESSOR CS14K6E-PFV 4A BOLT 8x GROMMET SPACER FRAME (C) - 3A T2 SCREW 4X8 7P DRIER CW-0325-S 4A DRIER BRACKET - 4A T2 SCREW 4X8 7P EXPANSION VALVE HFE-10NHD-2 4A EXP. VALVE COVER PE FOAM 3A EVAPORATOR G TRUSS HEAD SCREW SS, 4X8 7C T2 SCREW SS, 4X8 7P THERMISTOR HOLDER - THERMISTOR COPPER INSULATION - THERMISTOR PE FOAM CABLE TIE CV PRESSURE SWITCH ACB-2UB PRESSURE SWITCH BRACKET GS T2 SCREW 4X8 7P HOT GAS VALVE BRACKET GS T2 SCREW 4X8 7P

21 : KM-1300MWH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 30 LINE VALVE BRACKET - 4A T2 SCREW 4X8 7P VALVE BODY COIL - VALVE ABS-25-1-HD BOLT F TRUSS HEAD SCREW 4X8 7C CONDENSER - 4A HEX HEAD BOLT W/WASHER (LF) 5X12 7B WATER REGULATOR V46DA-3 4A TRUSS HEAD SCREW 4X6 7C MALE CONNECTOR - 4A COPPER TUBE (A) COPPER 4A1991G COPPER TUBE (B) COPPER 3A1473G COPPER TUBE (A) HIGH SIDE COPPER 2A1692G COPPER TUBE (B) HIGH SIDE COPPER 4A1993G COPPER TUBE (C) HIGH SIDE COPPER 3A1475G COPPER TUBE - LINE VALVE COPPER 4A HEAT EXCHANGER - 1A0475G COPPER TUBE (L) - LOW SIDE COPPER 2A1666G COPPER TUBE (R) - LOW SIDE COPPER 2A1667G COPPER TUBE - HOT GAS COPPER 3A0213G COPPER TUBE (J) COPPER 3A1482G CHECK VALVE - 4A STRAINER COPPER TUBE ACCESS VALVE COPPER 3A1518G ACCESS VALVE

22 : KM-1300MWH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 56 HOLDER/EXP. VALVE 3/8-3A CLAMP INSULATION TUBE L= CABLE TIE CV INSULATED RUBBER TUBE G INSULATION HOLDER - 3A T2 SCREW SS, 4X8 7P INSULATION ENDCAP - 4A1413F CLAMP - 4A

23 KM-1300MRH B. REFRIGERATION CIRCUIT 1/2 23

24 KM-1300MRH B. REFRIGERATION CIRCUIT 2/2 24

25 : KM-1300MRH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 1 REAR PANEL G FT SCREW SS, 4X8 7F T2 SCREW 4X8 7P FRAME - 3A0350G FT SCREW SS, 4X8 7F T2 SCREW 4X8 7P COMPRESSOR CS14K6E-PFV 4A BOLT 8x GROMMET SPACER FRAME (C) - 3A T2 SCREW 4X8 7P DRIER CW-0325-S 4A ENDCAP - 4A1413F DRIER BRACKET - 4A T2 SCREW 4X8 7P EXPANSION VALVE HFE-10NHD-2 4A EXP. VALVE COVER PE FOAM 3A EVAPORATOR G TRUSS HEAD SCREW SS, 4X8 7C T2 SCREW SS, 4X8 7P THERMISTOR HOLDER - THERMISTOR COPPER INSULATION - THERMISTOR PE FOAM CABLE TIE CV RECEIVER HEX HEAD BOLT W/WASHER (LF) 5X10 7B

26 : KM-1300MRH TITLE: B. REFRIGERATION CIRCUIT REQUIRED 28 PRESSURE SWITCH ACB-1UB PRESSURE SWITCH BRACKET GS T2 SCREW 4X8 7P HOT GAS VALVE BRACKET GS T2 SCREW 4X8 7P LINE VALVE BRACKET GS 4A T2 SCREW 4X8 7P VALVE BODY COIL - VALVE ABS-25-1-HD BOLT 4x F TRUSS HEAD SCREW 4X8 7C COPPER TUBE (A) HIGH SIDE COPPER 2A1692G COPPER TUBE (B) HIGH SIDE COPPER 4A2030G COPPER TUBE (D) HIGH SIDE COPPER 3A1603G COPPER TUBE (E) HIGH SIDE COPPER 2A1672G COPPER TUBE LINE VALVE COPPER 4A HEAT EXCHANGER - 1A0475A COPPER TUBE (L) LOW SIDE COPPER 2A1666G COPPER TUBE (R) LOW SIDE COPPER 2A1667G COPPER TUBE - HOT GAS COPPER 3A0213G CHECK VALVE SKC A STRAINER COPPER TUBE ACCESS VALVE COPPER 3A1518G ACCESS VALVE COUPLING G TUBE HOLDER - L T2 SCREW 4X8 7P

27 : KM-1300MRH TITLE: B. REFRIGERATION CIRCUIT REQUIRED COUPLING G TUBE HOLDER - S T2 SCREW 4X8 7P HOLDER/EXP. VALVE 3/8-3A CLAMP INSULATION TUBE L= CABLE TIE CV INSULATED RUBBER TUBE G INSULATION HOLDER - 3A T2 SCREW SS, 4X8 7P INSULATION CLAMP - 4A

28 KM-1300MAH, MWH, MRH C. WATER CIRCUIT 28

29 : KM-1300MAH, MWH, MRH TITLE: C. WATER CIRCUIT REQUIRED F PUMP MOTOR ASSEMBLY (S-0731) A01 1 HEX HEAD BOLT W/WASHER (LF) SS, 5X12 7B WATER SUPPLY PIPE COPPER 4A0768G01 1 T2 SCREW 4X8 7P RUBBER GASKET NR WATER VALVE BRACKET GS T2 SCREW 4X8 7P WATER VALVE J U HOSE CLAMP SS, 18MM SPRAY TUBE PE 1A SPRAY TUBE PE 1A SPRAY GUIDE (A) PE PLATE SS 3A T2 SCREW SS, 4X10 7P CUBE GUIDE (A) SS CUBE GUIDE (B) ABS THUMBSCREW ABS, SS G FLOAT SWITCH STOP SS 4A HOSE (A) EPDM HOSE CLAMP SS, 25MM HOLDER PP DISTRIBUTOR ABS PLUG EPDM 4A DRAIN HOSE EPDM HOSE CLAMP SS, 27MM DRAIN VALVE (B) ABS 3A

30 : KM-1300MAH, MWH, MRH TITLE: C. WATER CIRCUIT REQUIRED 23 "O" RING 1AG G SPRING SS VALVE SHEET EPDM T2 SCREW SS, 4X16 7P HOSE (C) EPDM OVERFLOW CAP ABS OVERFLOW PIPE ABS "O" RING - 4A CONNECTOR - FLOAT SWITCH EPDM FLOAT SWITCH A TRUSS HEAD SCREW SS, 4X8 7C CONNECTOR ABS RUBBER RING TSE2571-5U COLLAR ABS T2 FLAT HEAD SCREW SS, 4X16 7P SPRING SS VINYL HOSE L= VINYL HOSE L= TEE EPDM 4A FLANGE EPDM SILICONE HOSE L= I BYPASS HOSE EPDM CORNER INSULATION (A) PE FOAM CORNER INSULATION (B) PE FOAM MALE ADAPTOR (442137A01) "O" RING 7611-P BALL VALVE VALVE HOLDER GS 3A FT SCREW 4X8 7F

31 : KM-1300MAH, MWH, MRH TITLE: C. WATER CIRCUIT REQUIRED 48 MICRO SWITCH V3L-lll-D8 4A TAPPING SCREW 3x HANDLE JH T2 SCREW 4X8 7P VINYL HOSE L= VINYL HOSE L= WATER SUPPLY TUBE PE 2A WATER SUPPLY TUBE PE 2A VINYL HOSE L=

32 KM-1300MAH, MWH, MRH D. CONTROL BOX ASSEMBLY 32

33 : KM-1300MAH, MWH, MRH TITLE: D. CONTROL BOX ASSEMBLY REQUIRED 1 CAPACITOR - STARTING MFD, 250V 3A CAPACITOR 35MFD, 370V 3A STRAP GS 4A T2 SCREW 4X8 7P STARTER A T2 SCREW 4X8 7P MAGNETIC CONTACTOR VC BRACKET BW F T2 SCREW 4X8 7P CAPACITOR 10MFD, 250V T2 SCREW 4X10 7P TRANSFORMER 26D285H 3A T2 SCREW 4X8 7P CONTROLLER BOARD - 2A BOARD SUPPORT CBLS37-M 4A CONTROL LABEL 4A THERMOSTAT A A TRUSS HEAD SCREW 4X6 7C TOGGLE SWITCH 8966K P PLUG HOUSING P P PLUG HOUSING P (RED) P RECEPTACLE HOUSING R P RECEPTACLE HOUSING R1 (RED) BUSHING SB BUSHING OCB BUSHING SB CONTROL BOX GS 2A1082G BUSHING OCB

34 KM-1300MAH E. LABEL LOCATION 34

35 : KM-1300MAH TITLE: E. LABEL LOCATION REQUIRED 1 EMBLEM - 4A LABEL PETP FILM 4A LABEL - PENGUIN (R) PETP FILM 4A LABEL - AIR FILTER PETP FILM MAINTENANCE LABEL PVC FILM CAUTION LABEL (F) PVC FILM CAUTION LABEL (K) PVC FILM WIRING LABEL PVC FILM 3A NAMEPLATE PES FILM 4A INSTRUCTION SHEET PAPER 2A TAG - WARNING: ELECTRICAL PAPER CONNECTION 12 INSTRUCTION LABEL PVC FILM MANUAL LABEL - BIN CONTROL PVC FILM LABEL - R404A PES FILM 4A CAUTION LABEL PVC FILM OPERATION LABEL - VALVE PVC FILM MANUAL LABEL PVC FILM RATING LABEL - 4A LABEL - CONTROL BOARD - 3A

36 KM-1300MWH E. LABEL LOCATION 36

37 : KM-1300MWH TITLE: E. LABEL LOCATION REQUIRED 1 EMBLEM - 4A LABEL PETP FILM 4A LABEL - PENGUIN (R) PETP FILM 4A MAINTENANCE LABEL PVC FILM CAUTION LABEL (K) PVC FILM WIRING LABEL PVC FILM 3A NAMEPLATE PES FILM 4A INSTRUCTION SHEET PAPER 2A TAG - WARNING: ELECTRICAL PAPER CONNECTION 10 INSTRUCTION LABEL PVC FILM MANUAL LABEL - BIN CONTROL PVC FILM LABEL - R404A PES FILM 4A CAUTION LABEL PVC FILM OPERATION LABEL - VALVE PVC FILM MANUAL LABEL PVC FILM RATING LABEL - 4A LABEL - CONTROL BOARD - 3A

38 KM-1300MRH E. LABEL LOCATION 38

39 : KM-1300MRH TITLE: E. LABEL LOCATION REQUIRED 1 EMBLEM - 4A LABEL PETP FILM 4A LABEL - PENGUIN (R) PETP FILM 4A MAINTENANCE LABEL PVC FILM CAUTION LABEL (K) PVC FILM WIRING LABEL PVC FILM 3A NAMEPLATE PES FILM 4A INSTRUCTION SHEET PAPER 2A TAG - FAN MOTOR LEADS - 4A TAG - WARNING: ELECTRICAL PAPER CONNECTION 11 INSTRUCTION LABEL PVC FILM MANUAL LABEL - BIN CONTROL PVC FILM LABEL CHARGE PES FILM 4A LABEL - R404A 4A CAUTION LABEL PVC FILM OPERATION LABEL - VALVE PVC FILM MANUAL LABEL PVC FILM RATING LABEL - 4A LABEL - CONTROL BOARD - 3A CAUTION - REMOTE LABEL - 4A CAUTION TAPE - 404A L=250 4A1535L CAUTION LABEL (H)

40 KM-1300MAH, MWH, MRH F. PUMP MOTOR ASSEMBLY 40

41 : KM-1300MAH, MWH, MRH TITLE: F. PUMP MOTOR ASSEMBLY REQUIRED 1 PUMP MOTOR M91A60SP201 2U PUMP FLANGE PC PUMP MOTOR BRACKET SS TOOTH WASHER SS, M6 7R HEXAGON BOLT SS, 6X40 7B SPLIT LOCK WASHER SS, M6 7L FLAT WASHER SS, M6 7F NUT SS, M6 7N MECHANICAL SEAL H5-PN, 8MM PACKING EPDM IMPELLER ABS PIN SS PUMP HOUSING ABS HEXAGON BOLT SS, 4X30 7B FLANGE NUT SS, M4 7J

42 KM-1300MAH, MWH, MRH G. ACCESSORIES 42

43 : KM-1300MAH, MWH, MRH TITLE: G. ACCESSORIES REQUIRED 1 INSTRUCTION MANUAL PAPER 91A1OD10A 1 2 UNIVERSAL BRACE GS 4A HEX HEAD BOLT SS, 5X12 7B