INSTALLATION AND MAINTENANCE INSTRUCTIONS For Chemline EC & EK Series Characterized Control Valves Sizes 1/2 6

Size: px
Start display at page:

Download "INSTALLATION AND MAINTENANCE INSTRUCTIONS For Chemline EC & EK Series Characterized Control Valves Sizes 1/2 6"

Transcription

1 INSTALLATION AND MAINTENANCE INSTRUCTIONS For Chemline EC & EK Series Characterized Control Valves Sizes 1/2 6 Installation (all sizes) 1. Before installation, check the stainless steel reinforcing rods as well as the bolts on the actuator. If necessary tighten them. 2. Make sure the piping and valve body are clean and free of any solid foreign material. 3. The valve should be mounted between full-face flanges. The valve housing can be damaged by improper installation and/or improper tightening of bolts. Follow bolt pattern diagram below. 4. You will find the valve number on the valve body. Shown on these tags are the valve working pressures and temperatures. Should working conditions change, check whether the material of the actuator or other parts are still appropriate. 5. Manual or actuated shut-off valves are recommended in front and behind the control valve for installation and future maintenance. Strainers are recommended to avoid damage to the seat and plug. 6. The valve can be installed in any position, but it is recommended mounting with the actuator in an upright position, if necessary the actuator should be supported. 7. Use low torque flange gaskets and washers to protect housing and flange surfaces. Chemline fullface flange gaskets require lower torques. Use chart as show below if using Chemline gaskets: RECOMMENDED BOLT TIGHTENING TORQUE CHART NOMINAL SIZE RECOMMENDED TORQUE 1/2 3/ (ft-lbs) 1-1-1/4-1-1/ (ft-lbs) 2 2-1/ (ft-lbs) (ft-lbs) (ft-lbs) 09/19/01 Page 1

2 CHEMLINE Installation & Maintenance Instructions Characterized Control Valves cont. 8. Flow direction is indicated on the valve housing by an arrow. Normal flow direction is with pressure against the plug. 9. Never exceed the maximum working pressure which is indicated on the name plate. The maximum working pressure decreases with increased temperature, as in the following chart. 10. The installation of a compressed-air conditioner is recommended. The maximum admissible air pressure is indicated on the name plate and dependent on the size of the actuator. IMPORTANT NEVER EXCEED THE MAXIMUM AIR PRESSURE. 11. The air connection at the actuator housing is G 1/4. It is fixed on the lower or upper cover of the actuator housing depending on the function of the actuator. Operating Specs, EC-Series: Air Filtration: 40 to 50 micron recommended Air connection: ¼ Body: Single seat globe-type Control signal: 3 15 psi, max 35 psi Installation: No limit on mounting orientation. Max Temp:PVC: 60C, PP:80C, PVDF/PTFE: 120C Nominal sizes: ½ to 4 Operation: NO, NC or DA Pressure rating:90 psi Spring range: 3 15 psi Sealing: Teflon PTFE Valve plug: Linear or equal percentage Valve lift: ½ -3/4 :15mm, 1-2 :25mm, 2-1/2-4 :40mm 09/19/01 Page 2

3 CHEMLINE Installation & Maintenance Instructions Characterized Control Valves cont. Operating Specs, EK-Series: Air Filtration: 40 to 50 micron recommended Air connection: ¼ Body: Single seat globe-type Control signal: 3 15 psi, max 90 psi; 4-20 ma Installation: No limit on mounting orientation. Max Temp: PVC:60C, PP:80C, PVDF/PTFE: 120C Nominal sizes: ½ to 4 Operation: NO, NC or DA Pressure rating:150 psi Spring range: 3 15 psi Sealing: Teflon PTFE Valve plug: Linear or equal percentage Valve lift: ½ -3/4 :15mm, 1-2 :25mm, 2-1/2-4 :40mm Weight: 5.2 kg Maintenance Refer to DRAWING IOD-104a: 1. On spring return closed valves, apply 15 psi air pressure to the actuator air connection. This must be done to avoid damaging the threads on the plug (14). 2. Remove body (15) from bonnet (10) by unscrewing nuts (6), washers (5) Remove threaded rods (7), ensure that rods are not loosed from the mounting plate (3). A strap wrench may be used. Avoid using a metal wrench on plastic valves or damage may occur Remove bonnet (10) from mounting plate (3). 2. Remove and replace body O-ring (12), and bellows O-ring (18). 4. Remove (unscrew) plug (14) from the stem (1). Bellows must be held while undoing the plug (14). Screw new plug into bellows hand-tight. IMPORTANT DO NOT ATTEMPT TO PULL BELLOWS OFF THE STEM OR DAMAGE WILL OCCUR TO THE THREADS 5. Remove seat (16) by inserting a tool into the holes (two small allen keys and a screwdriver work well). Turn counterclockwise. Remove and replace the seat O-ring (17). Use tool to replace seat by turning clockwise until hand-tight. Make sure seat (16) is flush against body (15). Check by looking through valve inlet. 6. Change or replace all O-rings and check all parts for wear and or abrasion, replace as necessary. 7. It is recommended that the spare parts be exchanged only by experienced personnel as different structural dimensions have to be taken into account during the assembly of the valve. Should major repairs be necessary, we recommend you send the valve back to Chemline. 8. To re-assemble valve, repeat steps 1 through 6 in reverse. 09/19/01 Page 3

4

5

6

7

8

9

10

11

12

13

14

15

EC4 SERIES CRYOGENIC VALVES 1/4 2 Sizes

EC4 SERIES CRYOGENIC VALVES 1/4 2 Sizes 12501 Telecom Drive, Tampa, FL 33637 Ph: (813) 978-1000 Fax: (813) 977-3329 www.cpc-cryolab.com INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 17/2.5.6 Rev. 0 EC4 SERIES CRYOGENIC VALVES 1/4 2 Sizes

More information

Installation, Operation and Maintenance Instructions

Installation, Operation and Maintenance Instructions Installation, Operation and Maintenance Instructions MODEL 5520 June 2002 1.0 GENERAL... 2 Model Number Information... 2 Features... 3 Specifications... 4 Table 1A. Flow Coefficients (C V ), Modified Percent

More information

Mounting and Operating Instructions EB 8091 EN. Pneumatic Control Valve Type and Type Type with 120 cm 2 actuator

Mounting and Operating Instructions EB 8091 EN. Pneumatic Control Valve Type and Type Type with 120 cm 2 actuator Pneumatic Control Valve Type 3510-1 and Type 3510-7 Type 3510-1 with 120 cm 2 actuator Type 3510-7 with 120 cm 2 actuator and integrated positioner Type 3510-1 with 60 cm 2 actuator Fig. 1 Pneumatic control

More information

Technical Instructions

Technical Instructions IS-P-595DB Double Seat - Balanced Valve - Bronze (Type DB) or Stainless Steel Trim (Type DS) Technical Instructions Description The Powers #11 Double Seat Balanced Valve Regulator (Bronze or Stainless

More information

Series 2200/2220 Control Valve. Operation and Maintenance SCOPE OF MANUAL MAINTENANCE DESCRIPTION VALVE INSTALLATION

Series 2200/2220 Control Valve. Operation and Maintenance SCOPE OF MANUAL MAINTENANCE DESCRIPTION VALVE INSTALLATION SCOPE OF MANUAL This instruction manual includes installation and maintenance information for the 1.00" and 2.00" Series 2200/2220 Control Valves. Refer to separate manuals for instruction covering controllers,

More information

Mounting and Operating Instructions EB 5868/5869 EN

Mounting and Operating Instructions EB 5868/5869 EN Electric Control Valves Types 3213/5857, 3213/5824, Types 3214/5824, 3214/3374, 3214/3274 with safety function: Types 3213/5825, 3214/5825, 3214/3374, 3214/3274 Pneumatic Control Valves Types 3213/2780-1,

More information

Standard Valves Series Globe Valves Series Angle Valves Series Way-Valves

Standard Valves Series Globe Valves Series Angle Valves Series Way-Valves Installation, Operation, Maintenance Instructions Standard Valves Series 035 000 Globe Valves Series 031 000 Angle Valves Series 033 000 3-Way-Valves 1 GENERAL INFORMATION These instructions are designed

More information

2001 SERIES CRYOGENIC BAR STOCK BODY VALVES

2001 SERIES CRYOGENIC BAR STOCK BODY VALVES 12501 Telecom Drive, Tampa, FL 33637 Ph: (813) 978-1000 Fax: (813) 977-3329 www.cpc-cryolab.com INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 17/4.5.2 Rev. 0 2001 SERIES CRYOGENIC BAR STOCK BODY

More information

Mounting and Operating Instructions EB 8053 EN. Series 250 Type and Type Pneumatic Control Valves

Mounting and Operating Instructions EB 8053 EN. Series 250 Type and Type Pneumatic Control Valves Series 250 Type 3252 1 and Type 3252 7 Pneumatic Control Valves Type 3252 High-pressure valve with Type 3277 Pneumatic Actuator and Type 3767 Electropneumatic Positioner Mounting and Operating Instructions

More information

STAINLESS STEEL ARES PNEUMATIC ANGLE-SEAT VALVE

STAINLESS STEEL ARES PNEUMATIC ANGLE-SEAT VALVE FEATURES The stainless steel ARES valve is intended for the automatic shut-off of networks of fluids. The full-bore, inclined-seat body and the excellent flow-rate coefficients allow for very low pressure

More information

Mounting and operating instructions EB Pneumatic Control Valve Type and Type Globe Valve Type 3522 ANSI Class 300

Mounting and operating instructions EB Pneumatic Control Valve Type and Type Globe Valve Type 3522 ANSI Class 300 Pneumatic Control Valve Type 3522-1 and Type 3522-7 Globe Valve Type 3522 ANSI Class 300 Fig. 1 Type 3522-7 Control Valve with integrated positioner Mounting and operating instructions EB 8822 Edition

More information

Globe Valve Type Fig. 1 Type 3241 Globe Valve. Mounting and Operating Instructions EB EN

Globe Valve Type Fig. 1 Type 3241 Globe Valve. Mounting and Operating Instructions EB EN Globe Valve Type 3241 Fig. 1 Type 3241 Globe Valve Mounting and Operating Instructions EB 8015-1 EN Edition July 2012 Contents Contents Page 1 Design and principle of operation.................... 4 2

More information

Mounting and Operating Instructions EB 8111/8112 EN. Series V2001 Valves Type 3321 Globe Valve

Mounting and Operating Instructions EB 8111/8112 EN. Series V2001 Valves Type 3321 Globe Valve Series V2001 Valves Type 3321 Globe Valve Type 3321 Globe Valve with rod-type yoke and Type 3372 Electropneumatic Actuator (350 cm²) Mounting and Operating Instructions EB 8111/8112 EN Edition June 2013

More information

Split Body Valves with Bellows Seal Series Globe Valves Series Angle Valves Series Way-Valves

Split Body Valves with Bellows Seal Series Globe Valves Series Angle Valves Series Way-Valves Installation, Operation, Maintenance Instructions Split Body Valves with Bellows Seal Series 025 300 Globe Valves Series 027 300 Angle Valves Series 028 300 3-Way-Valves 1 GENERAL INFORMATION These instructions

More information

Powers Controls 656 Powermite Valve with 3-inch Top Rebuilding

Powers Controls 656 Powermite Valve with 3-inch Top Rebuilding Powers Controls 656 Powermite Valve with 3-inch Top Rebuilding Technical Bulletin Document No. 155-240P25 TB 233 Description This Technical Bulletin describes the recommended method of rebuilding the 656

More information

M x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator

M x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator Installation Instructions Issue Date June 15, 2007 Supersedes November 15, 2002 M9000-53x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator Installation Parts Included

More information

CIRCLE SEAL CONTROLS

CIRCLE SEAL CONTROLS CIRCLE SEAL CONTROLS ATKOMATIC SOLENOID VALVES INSTALLATION, MAINTENANCE, AND OPERATION INSTRUCTIONS 3000 SERIES Bronze, Normally Closed, Direct Lift Installation Instructions WARNING: These instructions

More information

CATALOG. Actuated Diaphragm Valve DN PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL.

CATALOG. Actuated Diaphragm Valve DN PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL. CATALOG Actuated Diaphragm Valve DN 15-100 PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL. TABLE OF CONTENTS Type 186 - DN 12-15 (MA 10) 04 General information - Technical specification 04 Sectional

More information

TECHNICAL INSTRUCTIONS #11 REGULATOR Single Seat - Bronze Trim - Composition Disc

TECHNICAL INSTRUCTIONS #11 REGULATOR Single Seat - Bronze Trim - Composition Disc Page 1 TI595CD A Watts Industries Co. TECHNICAL INSTRUCTIONS #11 REGULATOR Single Seat - Bronze Trim - Composition Disc VALVE DESCRIPTION TABLE OF CONTENTS The Powers #11 Regulator is a self-actuating

More information

Mounting and Operating Instructions EB 8111/8112 EN. Valve Series V2001 Globe Valve Type 3321

Mounting and Operating Instructions EB 8111/8112 EN. Valve Series V2001 Globe Valve Type 3321 Valve Series V2001 Globe Valve Type 3321 Fig. 1 Type 3321 Valve with mounted rod-type yoke for pneumatic or electric actuators (partial view) Mounting and Operating Instructions EB 8111/8112 EN Edition

More information

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Version with handwheel Mounting and Operating Instructions EB 8039 EN Edition May 2016 Definition of signal

More information

BRONZE ZEUS PNEUMATIC ANGLE-SEAT VALVE

BRONZE ZEUS PNEUMATIC ANGLE-SEAT VALVE FEATURES The bronze ZEUS valve is intended for the automatic shutoff of networks of fluids. The full-bore inclined-seat body and the excellent flow-rate coefficients allow for very low pressure drops.

More information

485 - NC NO/DA DN

485 - NC NO/DA DN 485 - NC 285 - NO/DA DN 25-100 The 485/285 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic

More information

PNEUMATICALLY ACTUATED 2-WAY

PNEUMATICALLY ACTUATED 2-WAY 482 DN 25-65 The 482 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic efficiency by increasing

More information

Fisher RSS Lined Globe Valve

Fisher RSS Lined Globe Valve Instruction Manual D0990 November 009 RSS Valve Fisher RSS Lined Globe Valve Contents Introduction............................... Scope of Manual.......................... Description...............................

More information

Fisher RSS Lined Globe Valve

Fisher RSS Lined Globe Valve Instruction Manual D0990 RSS Valve July 07 Fisher RSS Lined Globe Valve Contents Introduction... Scope of Manual... Description... Educational Services... Specifications... Installation... Maintenance...

More information

M x Series Cast Iron Flanged Valve Linkage Kit for Tandem Mounting of M9000 Series Electric Actuators

M x Series Cast Iron Flanged Valve Linkage Kit for Tandem Mounting of M9000 Series Electric Actuators Issue Date June 15, 2007 Supersedes November 15, 2002 M9000-53x Series Cast Iron Flanged Valve Linkage Kit for Tandem Mounting of M9000 Series Electric Actuators Installation Parts Included Linkage Stem

More information

ONYX VALVE CO MODEL CAR, CAP-PFO Installation & Maintenance

ONYX VALVE CO MODEL CAR, CAP-PFO Installation & Maintenance ONYX VALVE CO MODEL CAR, CAP-PFO Installation & Maintenance OPERATION: (4-2010) The Onyx series CAR-PFO and CAP-PFO pinch valves fail open on loss of air. The simple spring and air bag arrangement drives

More information

Gate Valve Maintenance & Adjustment Procedures

Gate Valve Maintenance & Adjustment Procedures Gate Valve Maintenance & Adjustment Procedures 1 Table of Contents I. GATE AND BONNET O-RING 1.5-21 GATE VALVES...3 II. BELLOWS, PNEUMATIC STANDARD 1.5-21 GATE VALVES...5 III. ACTUATOR O-RING 1.5-21 GATE

More information

Powers Controls Powermite Two-Way Flared Valves Normally Open/Normally Closed

Powers Controls Powermite Two-Way Flared Valves Normally Open/Normally Closed Powers Controls Powermite Two-Way Flared s Normally Open/Normally Closed VP 656-5 Description The VP 656 normally open and normally closed flared valves are pneumatically operated valves designed to control

More information

Steam/Water Washdown Units Safety and Operation Installation and Maintenance Instructions

Steam/Water Washdown Units Safety and Operation Installation and Maintenance Instructions INSTALLATION AND MAINTENANCE INSTRUCTIONS IM-8-002-US October 2016 Steam/Water Washdown Units Safety and Operation Installation and Maintenance Instructions These instructions should be read by the Company

More information

GATE VALVE MAINTENANCE AND ADJUSTMENT PROCEDURES

GATE VALVE MAINTENANCE AND ADJUSTMENT PROCEDURES GATE VALVE MAINTENANCE AND ADJUSTMENT PROCEDURES Valve Maintenance Manual 1 May 15, 2001 Table of Contents TABLE OF CONTENTS... 2 I. GATE AND BONNET O-RING 0.625" - 21" GATE VALVES... 3 II. BELLOWS, PNEUMATIC

More information

Hose Length Custom Length Supply Line Options Ball Valve w/ PT UBY Strainer w/ PT and BDV

Hose Length Custom Length Supply Line Options Ball Valve w/ PT UBY Strainer w/ PT and BDV Model AC Circuit Sentry Automatic Balance Hose Kits - Submittal Hose Kit Size Flow Range *MFR Qty. 1/2".33-14 5 3/4".33-14 11 3/4" 5-50 11 1".33-14 20 1" 5-50 20 1-1/4" 5-50 30 **1-1/2" 5-50 44 **1-1/2"

More information

In combination with an actuator, e.g. a SAMSON Type 3271 or Type 3277 Pneumatic Actuator

In combination with an actuator, e.g. a SAMSON Type 3271 or Type 3277 Pneumatic Actuator Type 3241 Valve In combination with an actuator, e.g. a SAMSON Type 3271 or Type 3277 Pneumatic Actuator ANSI and JIS version Translation of original instructions Type 3241 Valve with Type 3271 Actuator

More information

CIRCLE SEAL CONTROLS

CIRCLE SEAL CONTROLS CIRCLE SEAL CONTROLS ATKOMATIC SOLENOID VALVES INSTALLATION, MAINTENANCE, AND OPERATION INSTRUCTIONS 13000 SERIES Stainless, Normally Closed, Direct Lift, 3-Way Valve Installation Instructions WARNING:

More information

Mounting and operating instructions EB 8093 EN. Series 240 Pneumatic Control Valve for Cryogenic Temperatures. Type and

Mounting and operating instructions EB 8093 EN. Series 240 Pneumatic Control Valve for Cryogenic Temperatures. Type and Series 240 Pneumatic Control Valve for Cryogenic Temperatures Type 3248-1 and 3248-7 Fig. 1 Type 3248 Cryogenic Valve with Type 3277 Pneumatic Actuator as globe and angle valve Mounting and operating instructions

More information

DL/DS Series Diaphragm Valve

DL/DS Series Diaphragm Valve DL/DS Series Diaphragm Valve Service Instructions DL Series (Lever Handle) Valve DS Series (Round Handle) Valve Valves are shown with tube butt weld ends. These instructions also apply to DL or DS series

More information

Series 250 Pneumatic Control Valves Type and

Series 250 Pneumatic Control Valves Type and Series 250 Pneumatic Control Valves Type 3252-1 and 3252-7 Fig. 1 Type 3252 High-pressure Valve with Type 3277 Pneumatic Actuator and Type 3767 i/p Positioner Edition November 1998 Mounting and operating

More information

ONYX VALVE CO MODEL DAO-PFO Installation & Maintenance

ONYX VALVE CO MODEL DAO-PFO Installation & Maintenance ONYX VALVE CO MODEL DAO-PFO Installation & Maintenance OPERATION: (4-2010) The Onyx DAO-PFO pinch valve is an open frame valve without housing enclosure and fails open on loss of air. The actuator drives

More information

MODEL 106/206-PG POWER OPERATED GLOBE VALVE Sizes 1/2" to 8" (106-PG) 3" to 10" (206-PG) Installation, Operating and Maintenance Instructions

MODEL 106/206-PG POWER OPERATED GLOBE VALVE Sizes 1/2 to 8 (106-PG) 3 to 10 (206-PG) Installation, Operating and Maintenance Instructions MODEL 106/206-PG POWER OPERATED GLOBE VALVE Sizes 1/2" to 8" (106-PG) 3" to 10" (206-PG) Installation, Operating and Maintenance Instructions DESCRIPTION: This valve is the basic component used for most

More information

Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body

Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body VF 599-1 Description Features Application The Flowrite VF 599 series two-way valves are designed to work with either a pneumatic

More information

Valve Series V2001 Three-way Valve Type 3323

Valve Series V2001 Three-way Valve Type 3323 Valve Series V2001 Three-way Valve Type 3323 Fig. 1 Type 3323 Valve with mounted rod-type yoke (partial view) Edition January 1999 Mounting and operating instructions E 8113/8114 EN 1. Design and principle

More information

DA Series Diaphragm Valve

DA Series Diaphragm Valve DA Series Diaphragm Valve Service Instructions Pneumatically Actuated Valve Toggle Valve Valve Valve Valves are shown with tube butt weld ends. These instructions also apply to DA series valves with any

More information

Ideal Installation. I & M Mark 67 (1/2 6 ) Control Line. Installation & Maintenance Instructions for Mark 67 Pressure Regulators

Ideal Installation. I & M Mark 67 (1/2 6 ) Control Line. Installation & Maintenance Instructions for Mark 67 Pressure Regulators I & M Mark (/ ) 0 Wasson Road Cincinnati, OH 0 USA Phone --00 Fax -8-00 info@richardsind.com www.jordanvalve.com Installation & Maintenance Instructions for Mark Pressure Regulators Warning: Jordan Valve

More information

Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body

Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body VF 599-1 Description Features Application The Flowrite VF 599 series two-way valves are designed to work with either a pneumatic

More information

ONYX VALVE CO MODEL DAO-PFC Installation & Maintenance

ONYX VALVE CO MODEL DAO-PFC Installation & Maintenance ONYX VALVE CO MODEL DAO-PFC Installation & Maintenance OPERATION: (4-2010) The Onyx DAO-PFC pinch valve is an open frame valve without housing enclosure and fails closed on loss of air. The actuator drives

More information

Globe type control valve

Globe type control valve Basically a globe type of control valve consists of two parts as follows: Main (globe) valve body Diaphragm type of pneumatic actuator This two valve s part is coupled by a special coupling when the air

More information

LNG Screw Down Non-Return Valve Installation, Operation and Maintenance Manual

LNG Screw Down Non-Return Valve Installation, Operation and Maintenance Manual Installation, Operation and Maintenance Manual Date of Issue: 04 August 2010 Page 1 of 27 QF 80: Issue 2 WARNING! BEFORE ANY INSTALLATION AND MAINTENANCE WORK CAN COMMENCE ENSURE THE VALVE AND SURROUNDING

More information

PRESSURE REDUCING CONTROL VALVE

PRESSURE REDUCING CONTROL VALVE PRESSURE REDUCING CONTROL VALVE 06/08 Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) X P/L Standard Components 1 Main

More information

CVS Series H-900, H-1500 and H-2500 Design Valve Bodies

CVS Series H-900, H-1500 and H-2500 Design Valve Bodies Instruction Manual CVS Series H-900, H-1500 and H-2500 Design Valve Bodies Introduction Contents Contained in this manual are installation instructions, maintenance procedures and parts information for

More information

ONYX VALVE CO MODEL DAC-PFO Installation & Maintenance

ONYX VALVE CO MODEL DAC-PFO Installation & Maintenance ONYX VALVE CO MODEL DAC-PFO Installation & Maintenance OPERATION: (01-10) The Onyx series DAC-PFO pinch valve fails open on loss of air. This simple spring and air bag arrangement that drives a pair of

More information

Product Manual. CVS Series D Globe and Series DA Angle Style Valves. Introduction. Applications and Features

Product Manual. CVS Series D Globe and Series DA Angle Style Valves. Introduction. Applications and Features Product Manual CVS Series D Globe and Series DA Angle Style Valves Introduction Contained in this manual are installation instructions, maintenance procedures and parts information for the -inch and 2-inch

More information

Mounting and Operating Instructions EB 8048 EN. Type and Type Pneumatic Control Valves Type 3249 Aseptic Angle Valve

Mounting and Operating Instructions EB 8048 EN. Type and Type Pneumatic Control Valves Type 3249 Aseptic Angle Valve Type 3249-1 and Type 3249-7 Pneumatic Control Valves Type 3249 Aseptic Angle Valve Ball body version Special version with packing Type 3249-7 Control Valve with Type 3277 Actuator and integrated positioner

More information

Mustang Series PRESSURE REDUCING CONTROL VALVE. M115 (Globe) M1115 (Angle) Schematic. Standard Components. Options & Accessories.

Mustang Series PRESSURE REDUCING CONTROL VALVE. M115 (Globe) M1115 (Angle) Schematic. Standard Components. Options & Accessories. PRESSURE REDUCING CONTROL VALVE 02/09 Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) P/L Standard Components 1 Main Valve

More information

ONYX VALVE CO MODEL DAO-ADA Installation & Maintenance

ONYX VALVE CO MODEL DAO-ADA Installation & Maintenance ONYX VALVE CO MODEL DAO-ADA Installation & Maintenance OPERATION: (4-2010) The Onyx DAO-ADA pinch valve is an open frame valve without housing enclosure and fails last position on loss of air. This actuator

More information

WARNING Carefully Read These Instructions Before Use

WARNING Carefully Read These Instructions Before Use DO NOT RETURN THIS SPRAYER TO STORE Call: 1-800-950-4458 Backpack Sprayer Use and Care Manual Manufactured for Northern Tool + Equipment Co., Inc. WARNING Carefully Read These Instructions Before Use Model

More information

Mounting and Operating Instructions EB 8097 EN. Pneumatic Control Valves Type and Type

Mounting and Operating Instructions EB 8097 EN. Pneumatic Control Valves Type and Type Pneumatic Control Valves Type 3347-1 and Type 3347-7 Hollow-mold cast body with welding ends Full-mold cast body with threaded connections Fig. 1 Type 3347-7 Control Valve with Type 3277 Actuator and integral

More information

Instructions. Certifications Chrome less spray Chrome with spray 10-K82-WNCH-AD-Z Chrome less spray 10-K82-WYCH-AD-Z Chrome with spray

Instructions. Certifications Chrome less spray Chrome with spray 10-K82-WNCH-AD-Z Chrome less spray 10-K82-WYCH-AD-Z Chrome with spray Instructions *Image may vary slightly from actual product Tools Required Adjustable Wrench Groove Joint Pliers Pipe Wrench Phillips Screwdriver Pipe Tape or pipe thread compound Safety Tips If you solder

More information

LOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED

LOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED DIAPHRAGM BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to

More information

MODEL 5540 CONTENTS. Installation, Operation and Maintenance Instructions 1.0 GENERAL

MODEL 5540 CONTENTS. Installation, Operation and Maintenance Instructions 1.0 GENERAL Installation, Operation and Maintenance Instructions MODEL 5540 Sep 20 CONTENTS.0 GENERAL. Model Number---------------------------------------------------------------------------------------------------------------

More information

METERING VALVE 2" STEM GUIDED

METERING VALVE 2 STEM GUIDED 2" STEM GUIDED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be construed

More information

Mounting and Operating Instructions EB 8052 EN. Type 3251 Valve

Mounting and Operating Instructions EB 8052 EN. Type 3251 Valve Type 3251 Valve In combination with an actuator, e.g. a SAMSON Type 3271 or Type 3277 Pneumatic Actuator ANSI version Translation of original instructions Type 3251 Valve with Type 3271 Actuator Mounting

More information

Instruction Manual. CVS Series H-900, H-1500 and H-2500 Design Valve Bodies. Contents. Figure 1: Typical CVS Series H Design Body with Trim and Seals

Instruction Manual. CVS Series H-900, H-1500 and H-2500 Design Valve Bodies. Contents. Figure 1: Typical CVS Series H Design Body with Trim and Seals Instruction Manual CVS Series H-900, H-1500 and H-2500 Design Valve Bodies Contents Contained in this manual are installation instructions, maintenance procedures and parts information for the CVS Series

More information

Powers Controls Powertop Two-Way Valves Normally Open

Powers Controls Powertop Two-Way Valves Normally Open Powers Controls Powertop Two-Way s Normally Open VP 658-5 Description The VP 658 normally open valves are pneumatically operated valves designed to control the flow of both water and steam. Features Stainless

More information

B21 Series BASOTROL Gas Valve

B21 Series BASOTROL Gas Valve Installation Instructions B21 Issue Date September 19, 2017 Installation IMPORTANT: These instructions are intended as a guide for qualified personnel installing or servicing BASO Gas Products. Carefully

More information

PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance

PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance ACECO Valve P.O. Box 9 Mounds, Oklahoma 74047 PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance Doc. No.: IOM-PV4-.0 Date: 6/0-00 Revision: A Contents: Installation Operation

More information

PRESSURE REDUCING VALVE

PRESSURE REDUCING VALVE Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve

More information

PRESSURE REDUCING VALVE

PRESSURE REDUCING VALVE Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve

More information

User Manual for the ProFlow 1K Release: User Manual for the ProFlow 1K_Rev_A PVA Support Hub. User Manual for the ProFlow 1K

User Manual for the ProFlow 1K Release: User Manual for the ProFlow 1K_Rev_A PVA Support Hub. User Manual for the ProFlow 1K PVA Support Hub User Manual for the ProFlow 1K Collection of guides and pages for the operation and maintenance of the ProFlow 1K. Written By: Technical Writing 2017 support.pva.net Page 1 of 18 INTRODUCTION

More information

PRESSURE REDUCING VALVE

PRESSURE REDUCING VALVE Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Closes quickly when downstream pressure exceeds reduced pressure setpoint 3 PRESSURE REDUCING VALVE with SURGE

More information

Mounting and Operating Instructions EB 8256 EN. Type 3286 Steam Conditioning Valve

Mounting and Operating Instructions EB 8256 EN. Type 3286 Steam Conditioning Valve Type 3286 Steam Conditioning Valve In combination with an actuator, e.g. a SAMSON Type 3271 or Type 3277 Pneumatic Actuator DIN version Translation of original instructions Mounting and Operating Instructions

More information

3-way control valve in mixing and diverting design

3-way control valve in mixing and diverting design with electric and pneumatic actuators 3-way control valve in mixing and diverting design 1/2-6 STEVI 450 / 451 Electric actuator Enclosure IP 65 2 torque switches 1 travel switch Handwheel Additional devices

More information

Installation Instructions

Installation Instructions Installation Instructions Thermostatic Valve and Trim Model No. RH-5944 1 REV.A Restoration Hardware Product Size Specification Diagram General Characteristics In case of instantaneous heaters, hot water

More information

CV Control Valves Installation and Operation Manual

CV Control Valves Installation and Operation Manual CV1500 - Control Valves Installation and Operation Manual 652-EN Overview Warning: This bulletin should be used by experienced personnel as a guide to the installation of the Armstrong CV1500 Control Valve.

More information

Design CP Control Valve with ENVIRO-SEAL Bellows Seal Bonnet

Design CP Control Valve with ENVIRO-SEAL Bellows Seal Bonnet Instruction Manual Form 5410 November 1998 Design CP/ENVIRO-SEAL Bellows Seal Design CP Control Valve with ENVIRO-SEAL Bellows Seal Bonnet Contents Introduction.............................. 1 Scope of

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Part # 751-FP2500 IMPORTANT INFORMATION This Jagg oil cooler must be installed following these instructions. Read the easy-to-follow instructions fully prior to starting the installation

More information

Pressure Relief Valve Maintenance Manual

Pressure Relief Valve Maintenance Manual Technical Manual 1098T Pressure Relief Valve Maintenance Manual Farris Engineering Division of Curtiss-Wright Flow Control Corporation TABLE OF CONTENTS - Manual Revision 0 Introduction & Safety Tips...

More information

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS PART NUMBER: 102264 REVISION: "C" DATE: November 2000 Page 1 of 11 1.0 INTRODUCTION 1.1

More information

CONTROL VALVES. Installation, Maintenance & Operating Instructions. Read these instructions carefully before installation or servicing.

CONTROL VALVES. Installation, Maintenance & Operating Instructions. Read these instructions carefully before installation or servicing. KOSO HAMMEL DAHL CONTROL VALVES KOSO HAMMEL DAHL 253 Pleasant Street West Bridgewater, MA 02379 tel: 774.517.5300 fax: 774.517.5230 www.hammeldahl.com Installation, Maintenance & Operating Instructions

More information

DYNAFLUID 2000 STEAM & WATER MIXING VALVE INSTALLATION & OPERATING MANUAL

DYNAFLUID 2000 STEAM & WATER MIXING VALVE INSTALLATION & OPERATING MANUAL DYNAFLUID 2000 STEAM & WATER MIXING VALVE INSTALLATION & OPERATING MANUAL LILLY ENGINEERING COMPANY 217 CATALPA STREET P.O. BOX 173 ITASCA, ILLINOIS 60143 630-773-2222 FAX: 630-773-3443 www.lillyengineering.com

More information

Crispin Valves Operating Guide. Crispin

Crispin Valves Operating Guide. Crispin Crispin Valves Operating Guide Crispin Since 1905 Crispin Multiplex Manufacturing Co. 600 Fowler Avenue Berwick, PA 18603 1-800-AIR-VALV T: (570) 752-4524 F: (570) 752-4962 www.crispinvalve.com sales@crispinvalve.com

More information

Mounting and operating instructions EB EN. Differential Pressure and Temperature Regulator with Flow Limiter Type 2479/2430 K

Mounting and operating instructions EB EN. Differential Pressure and Temperature Regulator with Flow Limiter Type 2479/2430 K Differential Pressure and Temperature Regulator with Flow Limiter Type 2479/2430 K Special version DN 15 with differential pressure set point p = 0.5 bar Fig. 1 Type 2479/2430 K Mounting and operating

More information

Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body

Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body VF 599-1 VF114R1 VF115R1 Description Features Application The Flowrite VF 599 series two-way valves are designed to work with either

More information

Series 240 Type Gas and Type Gas Automatic Shut-off Valves for Gases (valve class D)

Series 240 Type Gas and Type Gas Automatic Shut-off Valves for Gases (valve class D) Series 240 Type 3241-1-Gas and Type 3241-7-Gas Automatic Shut-off Valves for Gases (valve class D) DIN-DVGW typetested acc. to DIN EN 161 (2013-04) Application Control valve for control systems subject

More information

Spira-trol TM Two-port Control Valves EN Standard LE, LF and LL DN15 to DN100 and ASME Standard LEA, LFA and LLA ½" to 4"

Spira-trol TM Two-port Control Valves EN Standard LE, LF and LL DN15 to DN100 and ASME Standard LEA, LFA and LLA ½ to 4 Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

Tri-Clover Manual and Air Actuated Fractional Valves

Tri-Clover Manual and Air Actuated Fractional Valves FVSM-99 Tri-Clover Manual and Air Actuated Fractional Valves Series 650 655 660 CONTENTS Thank you for purchasing a Tri-Clover Product! This manual contains disassembly and assembly instructions, maintenance

More information

SKD U Electronic Valve Actuator

SKD U Electronic Valve Actuator Document No. 129-217 SKD U Electronic Valve Actuator Product Description The SKD U actuator requires a 24 Vac supply signal to control a Flowrite 599 Series valve with a 3/4-inch (20 mm) stroke. Product

More information

INSTRUCTION MANUAL. Anchor Darling 1878 Swing Check Valves. Installation Operation Maintenance. Sizes 1/2 through 2 FCD ADENIM

INSTRUCTION MANUAL. Anchor Darling 1878 Swing Check Valves. Installation Operation Maintenance. Sizes 1/2 through 2 FCD ADENIM INSTRUCTION MANUAL Anchor Darling 1878 Swing Check Valves Sizes 1/2 through 2 Installation Operation Maintenance FCD ADENIM0006-00 Table of Contents 1.0 Physical Description and Operation of Equipment

More information

BETTIS ACTUATOR & CONTROLS SERVICE INSTRUCTIONS FIELD CONVERSION OF SPRING CARTRIDGE FAIL DIRECTION CLOCKWISE TO COUNTER-CLOCKWISE OR THE INVERSE

BETTIS ACTUATOR & CONTROLS SERVICE INSTRUCTIONS FIELD CONVERSION OF SPRING CARTRIDGE FAIL DIRECTION CLOCKWISE TO COUNTER-CLOCKWISE OR THE INVERSE BETTIS ACTUATOR & CONTROLS SERVICE INSTRUCTIONS FIELD CONVERSION OF SPRING CARTRIDGE FAIL DIRECTION CLOCKWISE TO COUNTER-CLOCKWISE OR THE INVERSE FOR THE FOLLOWING SERIES T3XX-SRX AND T4XX-SRX SPRING RETURN

More information

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves Type 3347-1 and Type 3347-7 Pneumatic Control Valves Type 3347-7, cast body with welding ends Type 3347-7, bar stock body with threaded connections Mounting and Operating Instructions EB 8097 EN Edition

More information

PNEUMATIC SLIDING VALVE

PNEUMATIC SLIDING VALVE INSTALLATION, OPERATION, & #: MM-SV001 6-23-09 Rev. A Page 1 of 8 PNEUMATIC SLIDING VALVE PART NUMBERS (Including, but not inclusive) SV704MSTS, SV714MSTS, SV754MSTS, SV764MSTS, SV774MSTS, SV706MSTS, SV716MSTS,

More information

Flowrite 599 Series Two-Way Valves, 1/2 to 2- inch Bronze Body, ANSI 250

Flowrite 599 Series Two-Way Valves, 1/2 to 2- inch Bronze Body, ANSI 250 Flowrite 599 Series Two-Way Valves, 1/2 to 2- inch Bronze Body, ANSI 250 Document No. 155-184P25 VF 599-3 Description The Flowrite 599 Series two-way valves are designed to work with either a pneumatic

More information

Maintenance-free metal-seated globe valves. Grey cast iron PN 16 DN Nodular cast iron PN 16 DN Nodular cast iron PN 25 DN

Maintenance-free metal-seated globe valves. Grey cast iron PN 16 DN Nodular cast iron PN 16 DN Nodular cast iron PN 25 DN Type Series Booklet 7150.1/9-10 BOA -H Maintenance-free metal-seated globe valves with bellows Grey cast iron PN 16 DN 15-300 Nodular cast iron PN 16 DN 15-350 Nodular cast iron PN 25 DN 15-150 Applications

More information

Globe valves Shut-off check valve 200 AE/BE PN DN Globe valves Lift check valve 240 MT PN DN 10-50

Globe valves Shut-off check valve 200 AE/BE PN DN Globe valves Lift check valve 240 MT PN DN 10-50 Globe valves Shut-off check valve 200 AE/BE PN 10-160 DN 10-50 Globe valves Lift check valve 240 MT PN 10-160 DN 10-50 Admissible operating pressure [bar] at design temperature [ C] 1) Material PN -200-60

More information

USERS MA UAL Bellow sealed valve Fig.229, 230, 234, 235 Edition: 1/2008

USERS MA UAL Bellow sealed valve Fig.229, 230, 234, 235 Edition: 1/2008 诲眾 ᓠ 睂睄 睄 ɞ 1/7 ZETKAMA Spółka Akcyjna ul. 3 Maja 12 PL 57-410 Ścinawka Średnia USERS MA UAL Bellow sealed valve Fig.229, 230, 234, 235 Edition: 1/2008 Date: 01.01.2008 CONTENTS 1. Product description

More information

3-way 1/2-2 Globe Valves

3-way 1/2-2 Globe Valves Datasheet Overview Designed to work with either an electronic actuator with a 3/4-inch (20 mm) stroke, the three-way globe valves are available in ANSI Class 250 for normally closed or normally open action.

More information

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Type 3535 Three-way Valve with bellows seal and rod-type yoke (partial view) Mounting and Operating Instructions EB 8135/8136 EN Edition

More information

INSTALLATION & MAINTENANCE MODEL mm

INSTALLATION & MAINTENANCE MODEL mm MODEL 65-25mm INSTALLATION INSTRUCTIONS CAUTION: Installation of Backflow Preventers must be performed by qualified, licensed personnel. The installer should be sure the proper device has been selected

More information

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an in-out filter.

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an in-out filter. Filter 10-1 Section 10 Filter NOTE: This section applies to applicators with an in-out filter. Table of Contents Filter...................................................... 10-1 Introduction................................................

More information

MP and MP Diaphragm and Seal Kits for MP8000 Series Actuators

MP and MP Diaphragm and Seal Kits for MP8000 Series Actuators MP8000-6325 and MP8000-6350 Diaphragm and Seal Kits for MP8000 Series Actuators Contents of the MP8000-6325 Diaphragm and Seal Kit for MP82 and MP83 Actuators One seal, 5/8 in. Internal Diameter (I.D.)

More information