GPA 13.8 kv Semi-Annual Slip Ring PM, Sav 10-41

Size: px
Start display at page:

Download "GPA 13.8 kv Semi-Annual Slip Ring PM, Sav 10-41"

Transcription

1 GPA 13.8 kv Semi-Annual Slip Ring PM, Sav Crane number Contrator Job # Inspection date: GPA Work Order # Inspected by: Trolley Hour Meter Reading Crane Hour Meter Reading Gantry Hour Meter Reading Hoist Hour Meter Reading SAFETY PRECAUTIONS: PRIOR TO SERVICING EQUIPMENT ALL ELECTRICAL AND MECHANICAL ENERGY SOURCES SHALL BE ISOLATED, DE-ENERGIZED, LOCKED OUT, AND TAGGED OUT. EQUIPMENT MAY BE POWERED FROM MULTIPLE SOURCES. PERSONAL PROTECTIVE EQUIPMENT IS REQUIRED TO PERFORM THIS (PM) PREVENTIVE MAINTENANCE PER NFPA 70E GUIDELINES. Tools required: 40 Kcal/cm2 flash 20 kv rated gloves Tic (voltage) tracer Hand Tools suit rated above 15kv 15 kv megger Ductor 10 amp Cleaning supplies Ladder Blower Shop vacuum Extension cords Generator Medium voltage PM Lock Out, Tag Out: All of the items below to be performed prior to starting any of the steps in this PM Ensure Crane is parked in agreement with GPA Crane Operations 912/ Ensure no persons are on the Crane to be de-energized Set crane stow pins (if possible) Connect 480 volt shore power when available Ensure Proper GPA personnel are notified that you are De-Energizing the circuit(crane) Identify the Medium Voltage Circuit breaker that feeds the crane to be serviced Turn Off Medium voltage Circuit Breaker following NFPA 70E guidelines 1 of 12

2 Rack out the Medium Voltage Circuit breaker following NFPA 70E guidelines Lock Out Medium voltage Circuit Breaker following NFPA 70E guidelines Ground Out Medium voltage Circuit Breaker following NFPA 70E guidelines, then Hang "Grounds Applied" sign on the De-Energized compartment door Procure the key for the Medium Voltage Compartments from the Switchgear cabinet MEGGER ALL CRANE FEEDERS FROM GEAR TO CRANE DISCONNECT at 15 kvdc. Record readings below o Note; Megging one phase while the other 2 phases are ungrounded will meg the whole system from the MV Breaker cubicle to the transformer. If the readings are low, then the circuit will have to be isolated between components/phases. o Caution: After megging it will take a long period of time for the cables to discharge. Use Caution prior to regrounding the system. Megger readings in Megohms for complete system OPTIONAL Megger readings in Megohms for A phase Megger readings in Megohms for B phase Megger readings in Megohms for C phase 2 of 12

3 Slip Ring Inspection Task List: Obtain the locks to the Slip Ring Cabinet from the Switchgear cabinet Verify that the Crane is De-Energized Unlock the padlocks on the Slip ring compartment Lubricate the padlocks Remove Slip Ring compartment doors Check the slip ring compartment for power following NFPA 70E guidelines Ground Out the slip rings following NFPA 70E guidelines Clean slip rings, brushes, and compartment with Non-Flammable Di-Electric solvent Inspect the Following per NETA Guidelines noting any deficiencies on the Test Sheet Cable Penetration Cable center packing Cable Reel fasteners Fire Extinguishers 3 of 12 Test the resistance between the slip rings and brushes with a Micro-ohmmeter note readings below. Results in microhms L1 L2 L3 Neutral Ground Remove grounds from slip ring compartment per NFPA 70E guidelines Install Slip Ring compartment doors Install Slip Ring compartment locks Torque Cable Reel bolts and nuts to manufacturers specifications, replace any defective parts. Inspect and verify spool cable entry gap is correct. Inspect Slip Ring area for any additional deficiencies

4 Change the oil in the slip ring gearbox following manufacturer s specified oil (EP-220). Inspect cable guide rollers. Inspect the cable dock level diverter. Inspect Ground shoes and note any deficiencies. Upriver Land side Downriver Land side Upriver River side Downriver River side LIST NOTES OR DISCREPANCIES BELOW: 4 of 12

5 Spreader Slip Ring Inspection Task List: Ensure Crane is parked in agreement with GPA Crane Operations Set crane stow pins (if possible) Identify the Circuit Breaker(s) that feed the Spreader Slip Ring Turn Off the Circuit Breaker(s) following NFPA 70E guidelines Lock Out the Circuit Breaker(s) following NFPA 70E guidelines Remove Spreader Slip Ring cover Verify that the Spreader Slip Ring is De-Energized following NFPA 70E guidelines Clean slip rings, brushes, and compartment with LP air(canned preferably) and dry rags where possible (DO NOT USE SOLVENTS OF ANYKIND) Inspect the Following per NETA Guidelines noting any deficiencies on the Test Sheet Check Spreader Slip Ring Motor Connections Ensure Spreader Slip Ring Gearbox oil is at correct level Ensure all associated mechanical and electrical fasteners on Spreader Slip Ring are in place and in functional condition Check Spreader Slip Ring collector housing condition Check condition of all rubber seals Check Spreader Slip Ring wire condition and wire connections Check for water intrusion in slip ring compartment & motor connections Check condition of kit plug Ensure Brake Lens cover is secure Check Encoder connections Check all fasteners on Motor, Pre-Reducer and Gearbox 5 of 12

6 Once cleaning is complete, test the resistance between the slip rings and brushes with a Micro-ohmmeter note readings below Wire Number Micro-ohmmeter Reading # 1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 #12 #13 #14 #15 #16 #17 #18 #19 #20 #21 #22 #23 #24 #25 #26 #27 #28 #29 #30 6 of 12

7 Install Spreader Slip Ring collector housing, and any removed covers Change the oil in the slip ring gearbox following manufacturer s specified oil (EP-220). Inspect Spreader Slip Ring area for any additional deficiencies Turn ON the Circuit Breaker(s) that feed the Spreader Slip Ring Inspect Spreader Slip Ring area after Powering up to ensure there are no issues Test operate Spreader Bar for proper function LS/WS Flippers Extend Spreader (20, 40, & 45) Retract Spreader (20, 40, & 45) Hoist Raise Hoist Lower Pins Engage Pins Dis-engage Return Crane to normal ops NETA: NFPA 70E: International Electrical Testing Association Inc. National Fire Protection Association Standard for Electrical Safety in the Workplace LIST NOTES OR DISCREPANCIES BELOW: 7 of 12

8 Gantry Cable Reel Drive Task List: Ensure crane is parked in accordance with GPA Crane Operations. Ensure no person(s) are on the crane to be de-energized. Set crane stow pins. (If possible) Check the compartment for power following NFPA 70E guidelines. Open the compartment doors and necessary covers. Check connections to all input and output modules. Check connections to control reset button. Verify control reset light(s) are functioning properly. Check connection to drive selection switch. Check connection to jog up and jog down buttons. Inspect the breaker(s) per the manufacturer s recommendations; ensure the breaker settings are returned to the proper settings. GCR Drive contactor #1; visually inspect for hotspots and connection point(s) are tight. GCR Drive contactor #2; visually inspect for hotspots and connection point(s) are tight. GCR brake #1 relay; visually inspect for hotspots and connection point(s) are tight. GCR brake #2 relay; visually inspect for hotspots and connection point(s) are tight. Remove the 30a filter fuses, visually inspect for hotspots and ensure all connections are tight. CRfltr (Filter); remove power and read across L1-L2-L3 and check for proper function. Open the 30a Cable Reel #1 circuit breaker for inspection; visually inspect for hotspots and loose connections. Open the 30a Cable Reel #2 circuit breaker for inspection; visually inspect for hotspots and loose connections. Close the breakers and reinstall the fuses. 8 of 12

9 Cavotec DTC Drive #1 Remove power to the drive 600 volt feed fuses. Check all connections. Check coil and associated connections. Read and verify braking resistor operation. CRBS1 Check all connections and look for hotspots. Check coil connections. Verify overload trip set; note setting found: ( ) Check output connection cable and connections. Check output cable connection brake status. Cable Reel Brake #1 Recifiers Test rectifier; verify bridge is complete. Verify output. Check connections. Cavotec DTC Drive #2 Remove power to the drive 600 volt feed fuses. Check all connections. Check coil and connection. Read and verify braking resistor operation. CRBS2 Check all connections and look for hot spots. Check coil connections. Verify overload trip set and note found setting; ( ) Check output connection cable and associated connections. Check output cable connection brake status. 9 of 12

10 Cable Reel Brake #2 Rectifiers Test rectifier and verify bridge is complete. Verify output. Check connections. Controls Located Remotely at the Cable Reel and/or Base of the Crane Cable reel resolver; verify connections and unit is secure. Check remote location control reset button; verify operation and connections are tight. Check jog up button; verify operation and connections are tight. Check jog down button; verify operation and connection are tight. Check connections and operation of drum empty / end of travel switch. Check connections and operation of feed point bypass switch. Check connections and operation of slack cable switch. At conclusion of inspection of Cavotec drives #1 and #2; Test drives. 10 of 12

11 Medium voltage PM Lock Out, Tag Out: The items below to be performed when all of the steps in this PM are complete Remove the grounds from the Medium Voltage Breaker compartment per NFPA 70E guidelines Install the rear door on the Medium Voltage Breaker Compartment Remove the "Grounds Applied" sign from the compartment door. Confirm all the grounds used on this job are accounted for, and the supervisor for the project has signed them in. Remove the Lock Out on the Circuit Breaker following NFPA 70E guidelines Rack in the Medium Voltage Circuit Breaker following NFPA 70E guidelines Ensure all personnel are clear Turn On the Medium Voltage Circuit Breaker Following NFPA 70E guidelines Contact Crane Operations for clearance to Boom down and operate the crane Lift Stow Pins Operate all Functions on the crane Run gantry left and right. Functionally check the slack limit switch and both over tension limits trip the gantry motion when activated. Monitor the cable reel resolver at the crane cms. Verify the value is correct and changes when the gantry is moved left and right. Boom Crane up Insert Stow Pins Notify operations and maintenance that work is complete and ( ) crane is ready for normal operations. LIST NOTES OR DISCREPANCIES BELOW: 11 of 12

12 NETA: International Electrical Testing Association Inc. NFPA 70E: National Fire Protection Association Standard for Electrical Safety in the Workplace 12 of 12

Pressure Makeup Jockey Pump Controller

Pressure Makeup Jockey Pump Controller Hubbell Industrial Controls, Inc. A subsidiary of Hubbell Incorporated 4301 Cheyenne Dr. Archdale, NC 27263 Telephone (336) 434-2800 FAX (336) 434-2803 Instruction Manual Pressure Makeup Jockey Pump Controller

More information

1500 Hour PM Inspection

1500 Hour PM Inspection 1500 Hour PM Inspection Electrical Start Time Stop Time 1. Perform initial walk around RTG prior to start and verify no excessive damage to crane. Report to Maintenance team immediately if damage is found

More information

ELECTRICIAN TRAINING SKILL DEVELOPMENT GUIDE

ELECTRICIAN TRAINING SKILL DEVELOPMENT GUIDE Q-01b ELECTRICIAN TRAINING SKILL DEVELOPMENT GUIDE Duty Q: Cranes and Hoists Q-01b: PM/Troubleshoot/Repair Crane (15 Ton) Issued 01/01/99 Task Preview PM/Troubleshoot/Repair Crane A Preventive Maintenance

More information

B-03 ELECTRICIAN TRAINING SKILL DEVELOPMENT GUIDE

B-03 ELECTRICIAN TRAINING SKILL DEVELOPMENT GUIDE B-03 ELECTRICIAN TRAINING SKILL DEVELOPMENT GUIDE Duty B: Power Distribution (600V and below) B-03: Troubleshoot 480V System Issued 06/01/98 Task Preview Troubleshoot 480V System The 480V distribution

More information

ELECTRICAL AREA CONTROLLED ACCESS PROCEDURE SP-18 NATIONAL HIGH MAGNETIC FIELD LABORATORY NHMFL FLORIDA STATE UNIVERSITY SAFETY PROCEDURE SP-18

ELECTRICAL AREA CONTROLLED ACCESS PROCEDURE SP-18 NATIONAL HIGH MAGNETIC FIELD LABORATORY NHMFL FLORIDA STATE UNIVERSITY SAFETY PROCEDURE SP-18 NATIONAL HIGH MAGNETIC FIELD LABORATORY NHMFL FLORIDA STATE UNIVERSITY SAFETY PROCEDURE SP-18 CONTROLLED ACCESS PROCEDURE HEAD of MAGNET OPERATIONS Bryon Dalton EH&S MANAGER Angela Sutton HEAD OF FACILITIES

More information

Appendix C. Interval Every 2 Year. Functional Test Weekly Monthly Quarterly. Semi. Every 3. Engineering Studies

Appendix C. Interval Every 2 Year. Functional Test Weekly Monthly Quarterly. Semi. Every 3. Engineering Studies Engineering Studies Coordination Study Every 5 years and in conjunction with electrical system modifications. Short Circuit Study NETA MTS 6.2 Every 5 years and in conjunction with electrical system modifications.

More information

PUB NLH 174 Island Interconnected System Supply Issues and Power Outages Page 1 of 4

PUB NLH 174 Island Interconnected System Supply Issues and Power Outages Page 1 of 4 PUB NLH 174 Island Interconnected System Supply Issues and Power Outages Page 1 of 4 1 2 3 4 5 6 7 8 9 Q. Please describe Hydro s terminal station and substation inspections policies and practices. In

More information

Notice. Overhead Crane Safety and Inspection Requirements. Daily Operator Inspection Reuirements. Daily Operator Inspection Requirements

Notice. Overhead Crane Safety and Inspection Requirements. Daily Operator Inspection Reuirements. Daily Operator Inspection Requirements Notice Overhead Crane Safety and Inspection Requirements It is the responsibility of the Owner/User to install, inspect, test, maintain, and operate a crane or associated lifting equipment in accordance

More information

Derailment Detector Assembly

Derailment Detector Assembly Derailment Detector Assembly Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences, directly

More information

IB PowlVac ITE-HK Remote Racking Device

IB PowlVac ITE-HK Remote Racking Device IB-51802 PowlVac ITE-HK Remote Racking Device for use with ITE-HK 5kV & 15kV Circuit Breakers and PowlVac ITE-HK 5kV & 15kV Replacement Circuit Breakers Powered by Safety PowlVac ITE-HK Remote Racking

More information

ibusway for Data Center

ibusway for Data Center ibusway for Data Center PBPQOD Plug-In Units with 15 60 A Circuit Breakers for Use On Busway Straight Sections Class 5600 Installation S1B99523 06/2012 Hazard Categories and Special Symbols Read these

More information

Level Lifter Ground Entry Lift Table Service Manual

Level Lifter Ground Entry Lift Table Service Manual Level Lifter Ground Entry Lift Table Service Manual LIFT PRODUCTS INC PO BOX 349 ELM GROVE WI 53122 262-521-5720 FAX 262-521-5725 Toll Free 877-543-8776 Model: Level Lifter s (LL Series) S/N Customer SETTING

More information

CENTRIFUGAL CHILLER. Lubrication System Pull oil sample for spectroscopic analysis.

CENTRIFUGAL CHILLER. Lubrication System Pull oil sample for spectroscopic analysis. CENTRIFUGAL CHILLER Annual Inspection Refrigerant Circuit Check and record refrigerant level Inspect for leak results Calculate refrigerant lass and report to the customer. Repair minor leaks as required

More information

PAD-MOUNTED SWITCHGEAR INSPECTION & MAINTENANCE RECOMMENDATIONS TYPE PSI/II. 15kV 25kV. Qualified Persons

PAD-MOUNTED SWITCHGEAR INSPECTION & MAINTENANCE RECOMMENDATIONS TYPE PSI/II. 15kV 25kV. Qualified Persons Page 1 Qualified Persons... 1 Safety Information... 2 Procedures... 3 Maintenance... 3 Security Inspection (Exterior)... 3 Verify Securing Devices... 3 Maintaining the Exterior... 3 Replacing Labels...

More information

Door Restrictor Assembly. Model R2

Door Restrictor Assembly. Model R2 Door Restrictor Assembly Model R2 Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences,

More information

MY-TE. OPERATION and MAINTENANCE. Winch and Hoist. Provided by: Model AC 36B OF MAX AC VOLT AC

MY-TE. OPERATION and MAINTENANCE. Winch and Hoist. Provided by:   Model AC 36B OF MAX AC VOLT AC Provided by: www.hoistsdirect.com Model AC 36B 6000# Double Line Lift Capacity MY-TE Winch and Hoist OPERATION and MAINTENANCE OF MAX AC 368-115 VOLT AC READ THIS BEFORE OPERATING UNIT INSTALLATION: Mount

More information

Exercise 1-1. Lockout/Tagout Procedure EXERCISE OBJECTIVE DISCUSSION. Become familiar with the Industrial Controls Training System.

Exercise 1-1. Lockout/Tagout Procedure EXERCISE OBJECTIVE DISCUSSION. Become familiar with the Industrial Controls Training System. Exercise 1-1 Lockout/Tagout Procedure EXERCISE OBJECTIVE Become familiar with the Industrial Controls Training System. Understand and perform proper lockout/tagout procedures during industrial servicing

More information

Overload Warning System DS 50

Overload Warning System DS 50 Overload Warning System DS 50 Grove - FMTV Trouble Shooting Manual Level 1 - Basics - 1 Table of contents Troubleshooting Manual PAT Overload Warning system DS 50 Level 1 -Basics- Item Content Page 1.

More information

C802/C802D/C802TD/C820 Alternators Troubleshooting Guide

C802/C802D/C802TD/C820 Alternators Troubleshooting Guide C802/C802D/C802TD/C820 Alternators Troubleshooting Guide Hazard Definitions These terms are used to bring attention to presence of hazards of various risk levels or to important information concerning

More information

2015 EDITION SUBMERSIBLE MOTORS AIM MANUAL. APPLICATION INSTALLATION MAINTENANCE 60 Hz, Single-Phase and Three-Phase Motors. franklinwater.

2015 EDITION SUBMERSIBLE MOTORS AIM MANUAL. APPLICATION INSTALLATION MAINTENANCE 60 Hz, Single-Phase and Three-Phase Motors. franklinwater. 0 EDITION AIM MANUAL SUBMERSIBLE MORS APPLICATION INSTALLATION 60 Hz, Single-Phase and Three-Phase Motors franklinwater.com All Motors System Troubleshooting Motor Does Not Start A. No power or incorrect

More information

Trimline Car and Sling

Trimline Car and Sling Trimline Car and Sling Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences, directly

More information

Four Corners Mine. Lockout Procedures. 15 Dragline

Four Corners Mine. Lockout Procedures. 15 Dragline Four Corners Mine Lockout Procedures BE 15 Dragline Revision Log Rev. No. Requested By Approved By Revised By Rev. Date 0 Initial Issue FCO Mine Safety B. Marceaux 05.07.07 Committee 1 Electrical Department

More information

A. This Section includes ac, enclosed controllers rated 600 V and less, of the following types:

A. This Section includes ac, enclosed controllers rated 600 V and less, of the following types: SECTION 262913 600 VOLT ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 0 Specification

More information

PAGE 1 OF 5 HEALTH, SAFETY & ENVIRONMENTAL MANUAL PROCEDURE: S360 Overhead Cranes & Lifts Procedure REV 4.0 8/14/2012

PAGE 1 OF 5 HEALTH, SAFETY & ENVIRONMENTAL MANUAL PROCEDURE: S360 Overhead Cranes & Lifts Procedure REV 4.0 8/14/2012 PAGE 1 OF 5 PURPOSE: OVERHEAD CRANES AND LIFTS PROCEDURE The purpose of this procedure is to define the safety and training requirements for use of overhead cranes and lifts. Procedure: Definitions Designated

More information

2018 KSB Pump Maintenance Event (Revised 10/16/2017)

2018 KSB Pump Maintenance Event (Revised 10/16/2017) Introduction: The purpose of this event is to test the skills of a maintenance team to respond to trouble at a sanitary sewer lift station that has resulted in an alarm. Premise: A pump trouble alarm was

More information

LED Downlight Ceiling Fixtures

LED Downlight Ceiling Fixtures ED Downlight Ceiling Fixtures Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences, directly

More information

BP OIL -- TOLEDO REFINERY

BP OIL -- TOLEDO REFINERY BP OIL -- TOLEDO REFINERY Document Type: Procedure Effective Date: August 31, 2017 Owner: Dane P. Clark Refinery Wide Electrical Distribution System Switching and Isolation Auth. By: Rick J. Chmelovski

More information

6. Document tasks performed during visit and report any observations to the appropriate

6. Document tasks performed during visit and report any observations to the appropriate Chiller Annual Maintenance RFP Attachment B Services Required Tasking: Vibration Analysis 1. All work shall be performed in accordance with safety policies 2. Check with appropriate customer representative

More information

OPERATING INSTRUCTIONS. ASTRO HOIST Type E89-CTO

OPERATING INSTRUCTIONS. ASTRO HOIST Type E89-CTO OPERATING INSTRUCTIONS ASTRO HOIST Type E89-CTO CONFORM TO EN 1808 - MARCH 1999 MACHINE DIRECTIVE 98/37 EC All persons operating this equipment must read and completely understand this manual. Any operation

More information

OPERATOR MANUAL Combo Belt Conveyor

OPERATOR MANUAL Combo Belt Conveyor 1 OPERATOR MANUAL Combo Belt Conveyor Document No. 11-01, Rev., 0816 2 WARNINGS THIS CONVEYOR IS DESIGNED FOR A SPECIFIC APPLICATION. CHECK FRAME AND METAL BELT FOR DAMAGE DURING SHIPMENT. READ THE MANUAL

More information

Installation Instructions Electric Heaters 5 20 kw

Installation Instructions Electric Heaters 5 20 kw Small Packaged Products 2 to 5 Tons Accessory Electric Heaters Cancels: IIK 564A-24-2 IIK 564A-24- -02 Installation Instructions Electric Heaters 5 20 kw NOTE: Read the entire instruction manual before

More information

MAINTENANCE EVALUATION CHECKLIST ELECTRIC ELEVATORS

MAINTENANCE EVALUATION CHECKLIST ELECTRIC ELEVATORS Manufacturer: Model: Evaluation Performed By: INTRODUCTION: This checklist will enable the user to make an objective appraisal of the condition of the equipment. Given the variety and complexity of the

More information

CALTRAP INSTALLATION AND OPERATIONS MANUAL

CALTRAP INSTALLATION AND OPERATIONS MANUAL INSTALLATION AND OPERATIONS MANUAL NOTE Please read this entire installation and operations manual before energizing the. Safety Considerations: Installing and servicing capacitor equipment can be hazardous.

More information

Power Break Circuit Breakers

Power Break Circuit Breakers Draw Out 800-4000 Amperes GEH-46988 Installation Instructions Power Break Circuit Breakers POWER BREAK Draw Out Circuit Breaker (SOOA 4000A) DESCRIPTION Types TC, and THC Power Break draw out circuit breakers

More information

General Instructions and Inspection Instructions for Crane

General Instructions and Inspection Instructions for Crane General Instructions General Instructions and Inspection Instructions for Crane Distributed by Ergonomic Partners Sales@ErgonomicPartners.com www.ergonomicpartners.com Tel: 314-884-8884 EN R_(EN)/1 --

More information

2. AC SERVICE AND MOTOR REQUIRED 1. ENCLOSURE REQUIRED

2. AC SERVICE AND MOTOR REQUIRED 1. ENCLOSURE REQUIRED 1. ENCLOSURE REQUIRED If the OC1 control is furnished as an open-chassis unit (standard), mount control in an enclosure 12 x 10 x 5 or larger and mount enclosure where room temperature does not exceed

More information

BOILER PM & INSPECTION

BOILER PM & INSPECTION BOILER PM & INSPECTION Record inspection log for Gaming Commission and Safety Department. The following listed maintenance items are not intended to be a complete list. Follow any additional maintenance

More information

UBC Technical Guidelines Section Edition Commissioning of Electrical Systems Page 1 of 5

UBC Technical Guidelines Section Edition Commissioning of Electrical Systems Page 1 of 5 Page 1 of 5 1.0 GENERAL 1.1 Coordination Requirements.1 UBC Building Operations Electrical Technical Support.2 UBC Energy & Water Services 2.0 REQUIREMENTS FOR COMMISSIONING AND TESTING 2.1 Testing.1 Unit

More information

WIRING DESIGN & PROTECTION REQUIREMENTS CHECKLIST

WIRING DESIGN & PROTECTION REQUIREMENTS CHECKLIST WIRING DESIGN & PROTECTION REQUIREMENTS CHECKLIST Use & Identification of Grounded and Grounding Conductors YES NO N/A Grounded conductors are identifiable and distinguishable from all other conductors.

More information

SmartBoost 50 INSTALLATION INSTRUCTIONS & OWNER S MANUAL LT93 SMTBST50 1. Issue 1 Print 2 AUTOMATIC SHORELINE TRANSFORMER

SmartBoost 50 INSTALLATION INSTRUCTIONS & OWNER S MANUAL LT93 SMTBST50 1. Issue 1 Print 2 AUTOMATIC SHORELINE TRANSFORMER SmartBoost 50 AUTOMATIC SHORELINE TRANSFORMER INSTALLATION INSTRUCTIONS & OWNER S MANUAL 1 Contents INTRODUCING... THE SmartBoost 50............................................................ 3 Manual

More information

OutdoorXUPS-600AHV-8364

OutdoorXUPS-600AHV-8364 OutdoorXUPS-600AHV-8364 TSi Power s OutdoorXUPS-600AHV-8364 provides secure and uninterrupted 230 vac power to critical loads. 1) Weather-tight metal cabinet (IP44 or NEMA 3R rated) 2) 2A and 2B are wide

More information

Cutler-Hammer. Instructions for Installation, Operation, and Maintenance of the AMPGARD Reduced Voltage Soft Starter

Cutler-Hammer. Instructions for Installation, Operation, and Maintenance of the AMPGARD Reduced Voltage Soft Starter Operation, and Maintenance of the Instruction Bulletin Read and understand these instructions before attempting any installation, operation, or maintenance of the. This equipment shall be installed and

More information

Hanna Daily Preventive Maintenance Schedule

Hanna Daily Preventive Maintenance Schedule Hanna Daily Preventive Maintenance Schedule Location Location # Daily operation and inspection procedures to be performed by car wash personnel. Mark status in the spaces on the right after performing

More information

INSTRUCTIONS FOR THE RELIANCE CONTROLS ARM SERIES AUTOMATIC TRANSFER SWITCH

INSTRUCTIONS FOR THE RELIANCE CONTROLS ARM SERIES AUTOMATIC TRANSFER SWITCH INSTRUCTIONS FOR THE RELIANCE CONTROLS ARM SERIES AUTOMATIC TRANSFER SWITCH THE RELIANCE CONTROLS ARM SERIES AUTOMATIC TRANSFER SWITCH IS NOT FOR "DO-IT-YOURSELF" INSTALLATION. It must be installed by

More information

ATV/UTV WINCH INSTRUCTION BOOK 3000 LBS

ATV/UTV WINCH INSTRUCTION BOOK 3000 LBS ATV/UTV WINCH INSTRUCTION BOOK 3000 LBS As you read these instructions, you will see WARNINGS and CAUTIONS. Each message has a specific purpose. WARNINGS and CAUTIONS identify the hazard, indicate how

More information

BREAK-SAFE Load Break & Pick-up Tool

BREAK-SAFE Load Break & Pick-up Tool BREAK-SAFE Load Break & Pick-up Tool USBS-15-1-PS USBS-15-2-PS USBS-27-1-PS USBS-27-2-PS USBS-38-1-PS USBS-38-2-PS USBS-46-1-PS USBS-46-2-PS Available Options: H - Hard Case S - Soft Case Second Generation

More information

Instructions for VCP-W Simple Electrical Ground & Test Device (SEG&TD) with simplified interlock scheme - bottom terminal set version

Instructions for VCP-W Simple Electrical Ground & Test Device (SEG&TD) with simplified interlock scheme - bottom terminal set version IB131018EN Instructions for VCP-W Simple Electrical Ground & Test Device (SEG&TD) with simplified interlock scheme - bottom terminal set version Contents Description Page 1. Introduction...2 2. Description...2

More information

JBI Docupunch P33 Automatic Punch

JBI Docupunch P33 Automatic Punch JBI Docupunch P33 Automatic Punch Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com TABLE OF CONTENTS SECTION I: INSTALLATION & TESTING: 1) Uncrating, Inspection & removal

More information

Electrical Safety. Introduction

Electrical Safety. Introduction Electrical Safety Introduction Electrical hazards 300 electrocutions every year in the U.S. Leading cause is insufficient training ALL were preventable What is Electricity? How Electricity Works Created

More information

GE Industrial Solutions. User/Installation Manual for 4.76kV -15kV SecoBloc

GE Industrial Solutions. User/Installation Manual for 4.76kV -15kV SecoBloc GE Industrial Solutions User/Installation Manual for 4.76kV -15kV SecoBloc Index General Scope...3 Standards...3 Operating conditions...3 Technical specification...3 Basic structure Features...4 Operation...4

More information

Optional Bullard Hook* with return latch, with or without return spring, for added safety.

Optional Bullard Hook* with return latch, with or without return spring, for added safety. Standard Top Hook with safety latch-rigid (standard) or swivel. Optional Bullard Hook* with return latch, with or without return spring, for added safety. Optional Shur-Loc Hook* with positive lock latch

More information

Electric Motor Controls BOMA Pre-Quiz

Electric Motor Controls BOMA Pre-Quiz Electric Motor Controls BOMA Pre-Quiz Name: 1. How does a U.P.S. (uninterruptable power supply) work? A. AC rectified to DC batteries then inverted to AC B. Batteries generate DC power C. Generator, batteries,

More information

Hunter Automatics HA-8. Installation Manual

Hunter Automatics HA-8. Installation Manual Hunter Automatics HA-8 Installation Manual WARNING TO REDUCE RISK OF INJURY 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE

More information

E.S.P. Embedded Sensing Probes for Motor Brushes

E.S.P. Embedded Sensing Probes for Motor Brushes E.S.P. Embedded Sensing Probes for Motor Brushes 2/13 Installation & Operating Manual MN609 Any trademarks used in this manual are the property of their respective owners. Important: Be sure to check www.baldor.com

More information

Switchgear Skid, C1192

Switchgear Skid, C1192 CUSTOM SOLUTIONS 15kV Modular Stairs stored on floor in front of battery bay Ground grid stored on front tongue of trailer Stairs deployed for unit access Storage box for fencing materials and other parts

More information

1900AL Electric Mining Shovel Product Overview

1900AL Electric Mining Shovel Product Overview 1900AL Electric Mining Shovel Product Overview 1900AL Shovel Taking the Next Step: Building on Proven Success When the P&H 1900AL was introduced in 1977, the result was one of the most rugged, reliable,

More information

REVELSTOKE - 1 YEAR DOWN. Applied to Equipment Instruction Number R Class-Group Generate Date: 11 March 2004

REVELSTOKE - 1 YEAR DOWN. Applied to Equipment Instruction Number R Class-Group Generate Date: 11 March 2004 Page 1 of 7 Planned Maint. Type Turbo file - Job Group 1Y-DOWN Lead Trade Applied to Equipment Instruction Number R Class-Group Generate Date: 11 March 2004 Isolation Zone Supersedes References J:\PS\mep\Maintenance

More information

Vacuum Circuit Breaker Type VAD-3

Vacuum Circuit Breaker Type VAD-3 Instruction Bulletin Bulletin 6055-11 Vacuum Circuit Breaker Type VAD-3 4.76 kv, 29 ka (250 MVA) 4.76 kv, 41 ka (350 MVA) 8.25 kv, 33 ka (500 MVA) 15.0 kv, 18 ka (500 MVA) 15.0 kv, 28 ka (750 MVA) 15,0

More information

APPENDIX B SPECIFICATION FOR GENERATOR OVERHAUL EMD MODEL AR10 D18... B-1

APPENDIX B SPECIFICATION FOR GENERATOR OVERHAUL EMD MODEL AR10 D18... B-1 Table of Contents APPENDIX B SPECIFICATION FOR GENERATOR OVERHAUL EMD MODEL AR10 D18... B-1 B.01 SCOPE... B-1 B.02 GENERAL... B-1 B.03 ELECTRICAL QUALIFICATION... B-1 B.04 EQUIPMENT RECONDITIONING... B-2

More information

Removable Applied Panel Mounting System

Removable Applied Panel Mounting System Removable Applied Panel Mounting System Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences,

More information

SUBSTATION VACUUM CIRCUIT BREAKER (15.5KV)

SUBSTATION VACUUM CIRCUIT BREAKER (15.5KV) SUBSTATION VACUUM CIRCUIT BREAKER (15.5KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities

More information

SUBSTATION VACUUM CIRCUIT BREAKER (38KV)

SUBSTATION VACUUM CIRCUIT BREAKER (38KV) SUBSTATION VACUUM CIRCUIT BREAKER (38KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities

More information

SUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV)

SUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV) SUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products

More information

EISHO TEK. Vacuum Circuit Breaker

EISHO TEK. Vacuum Circuit Breaker EISHO TEK Vacuum Circuit Breaker TYPE:SV1-12 INSTRUCTION MANUAL Operation and Maintenance Version TAIWAN CALSONIC SAFETY PRECAUTIONS For safety reason, this equipment should be handled by personnel who

More information

Wingate Creek Mine. Lockout Procedures. 14 Dragline

Wingate Creek Mine. Lockout Procedures. 14 Dragline Wingate Creek Mine Lockout Procedures BE Revision Log Rev. No. Requested By Approved By Revised By Rev. Date 0 Initial Issue R. Barefield R. Barefield 12.03.08 1 Operations/Maint. Facility Mngt. R. Barefield

More information

TubeTrace Tubing Bundles

TubeTrace Tubing Bundles for Custom CEMS and Analytical Umbilicals English Units Receiving, Storing and Handling... 1. Inspect materials for damage incurred during shipping. Report damages to carrier for settlement. 2. Identify

More information

NSGV PT-1000 PORTABLE WELDING STATION I, O & M MANUAL

NSGV PT-1000 PORTABLE WELDING STATION I, O & M MANUAL APPLICATION OF DUST CONTROL EQUIPMENT: CAUTION - Warning Improper operation of dust control system may contribute to conditions in the work area or facility that could result in severe personal injury

More information

1. The term "withstand" means "the unit will remain in place without separation of any parts from the device when subjected to the seismic forces.

1. The term withstand means the unit will remain in place without separation of any parts from the device when subjected to the seismic forces. SECTION 262816 - ENCLOSED SWITCHES AND CIRCUIT BREAKERS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Fusible switches. 2. Nonfusible switches. 3. Receptacle switches. 4. Shunt trip switches. 5.

More information

Electrobar FS Conductor Bar System

Electrobar FS Conductor Bar System Electrobar FS Conductor Bar System Electromotive Part Number: 005-1066 R12 Copyright 2015 Magnetek Material Handling Table of Contents Chapter 1.0: Danger, Warnings and Cautions... 33 Chapter 2.0: Disconnecting

More information

PBA Series Prelube Controls

PBA Series Prelube Controls VARNA Products Engineered Innovation PBA Series Prelube Controls Simple, Compact, Industrial Full featured control for running prelube from the control or from a remote station Easy internal wiring connections

More information

EAVERLINE. Operator s Manual. Series 5 Feed Cart Models 521, 525, 531 & 537. Weaverline, LLC - Churchtown, PA 17555

EAVERLINE. Operator s Manual. Series 5 Feed Cart Models 521, 525, 531 & 537. Weaverline, LLC - Churchtown, PA 17555 EAVERLINE Operator s Manual Series 5 Feed Cart Models 521, 525, 531 & 537 CAUTION: Drive at a speed slow enough to ensure safety and complete control at all times. CAUTION: Know the controls and how to

More information

Overspeed Adjustable Valve

Overspeed Adjustable Valve Overspeed Adjustable Valve Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences, directly

More information

Installation Instructions For Motor Control Center (MCC) Units

Installation Instructions For Motor Control Center (MCC) Units s Page 1 of 8 Installation Instructions December, 2013 Installation Instructions For Motor Control Center (MCC) Units Hazardous voltage. Will cause death or serious injury. Always de-energize and ground

More information

1. Take the cover off the relay, taking care to not shake or jar the relay or other relays around it.

1. Take the cover off the relay, taking care to not shake or jar the relay or other relays around it. RC SCOPE This test procedure covers the testing and maintenance of Westinghouse RC relays. The Westinghouse Protective Relay Division was purchased by ABB, and new relays carry the ABB label. Refer to

More information

AVOIDING ELECTROCUTION HAZARDS

AVOIDING ELECTROCUTION HAZARDS Print AVOIDING ELECTROCUTION HAZARDS MODULE DESCRIPTION This module will provide information that helps you recognize and avoid common electrocution hazards in your work environment. OBJECTIVES After completing

More information

Freedom egen System End-of- Line Functional Checklist

Freedom egen System End-of- Line Functional Checklist U Freedom egen System End-of- Line Functional Checklist 976-0361-01-01 Rev A April 2018 DANGER RISK OF FIRE, ELECTRIC SHOCK, EXPLOSION, AND ARC FLASH This checklist is in addition to, and incorporates

More information

A system fault contribution of 750 mva shall be used when determining the required interrupting rating for unit substation equipment.

A system fault contribution of 750 mva shall be used when determining the required interrupting rating for unit substation equipment. General Unit substations shall be 500 kva minimum, 1500 kva maximum unless approved otherwise by the University. For the required configuration of University substations see Standard Electrical Detail

More information

50 AMP TRANSFER RELAY DELAY - DUAL INPUT GENSET

50 AMP TRANSFER RELAY DELAY - DUAL INPUT GENSET R 50 AMP TRANSFER RELAY DELAY - DUAL INPUT GENSET Transfer Relay Delay 00-00803-400 Dual Input Genset INDUSTRIAL CONTROL EQUIPMENT TYPE 1 Shore Power Rating: 120/240VAC 60HZ 1 Phase 50A/Pole Generator

More information

Horizontal Circuit Switchers

Horizontal Circuit Switchers > Transformer Protection > CIRCUIT SWITCHERS C A T A L O G B U L L E T I N General Application Southern States Types CSH and CSH-B Horizontal Circuit Switchers provide an economical, versatile, space saving

More information

BREAK-SAFE Load Break & Pick-up Tool

BREAK-SAFE Load Break & Pick-up Tool BREAK-SAFE Load Break & Pick-up Tool USBS-15-1-PS USBS-27-1-PS USBS-46-1-PS USBS-15-2-PS USBS-27-2-PS USBS-46-2-PS Available Options: H - Hard Case S - Soft Case Second Generation Models Only. For tools

More information

OPERATION MANUAL MODELS TWE-250 TWE-321 TWE-375 TRU WELD EQUIPMENT COMPANY 6400 N. HONEYTOWN ROAD SMITHVILLE, OHIO (330)

OPERATION MANUAL MODELS TWE-250 TWE-321 TWE-375 TRU WELD EQUIPMENT COMPANY 6400 N. HONEYTOWN ROAD SMITHVILLE, OHIO (330) OPERATION MANUAL MODELS TWE-250 TWE-321 TWE-375 TRU WELD EQUIPMENT COMPANY 6400 N. HONEYTOWN ROAD SMITHVILLE, OHIO 44677 (330) 669 2773 CONTENTS Section Description Pages 1 Introduction 3 2 External Features

More information

Installation Instructions Electric Heaters 5 20 kw

Installation Instructions Electric Heaters 5 20 kw Small Packaged Products to 5 Tons Accessory Electric Heaters Cancels: IIK 564A--1 IIK 564A-- 11-01 Installation Instructions Electric Heaters 5 0 kw NOTE: Read the entire instruction manual before starting

More information

Battery Operation. Battery Construction. Battery State Of Charge. Battery Load Test. Battery Rating Systems 2/14/12

Battery Operation. Battery Construction. Battery State Of Charge. Battery Load Test. Battery Rating Systems 2/14/12 Battery Operation Batteries, Charging and Donald Jones Brookhaven College Batteries convert chemical energy into electrical energy During discharge the battery s plate composition is changed During charging

More information

STARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS

STARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS TJ STARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS page DESCRIPTION AND OPERATION STARTER MOTOR... 2 STARTER RELAY... 3 STARTING SYSTEM... 1 DIAGNOSIS AND TESTING STARTER MOTOR... 8 STARTER MOTOR NOISE

More information

ASTA Handling System Installation & Operating Instructions

ASTA Handling System Installation & Operating Instructions ASTA Handling System Installation & Operating Instructions Part #s V2HS-03, V2HS-05LS & V2HS 01/25/11 Handling System Serial # ASTA Serial # Date: PRACTICAL SYSTEMS, INC. 11617 Prospect Road Odessa, FL

More information

Installation Instructions

Installation Instructions NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment

More information

Star Swivel-Arm Hoist Installation and Operating Instructions

Star Swivel-Arm Hoist Installation and Operating Instructions Star Swivel-Arm Hoist Installation and Operating Instructions Conveying & Hoisting Solutions P/L ABN 78 6 7. Purpose of Equipment Star Swivel-Arm Hoists are intended for the transport of materials. Star

More information

Instruction Manual 15kV KVAN-1125M 1200/2000A Maxi-Vac Medium-Voltage Vacuum Circuit Breaker

Instruction Manual 15kV KVAN-1125M 1200/2000A Maxi-Vac Medium-Voltage Vacuum Circuit Breaker Instruction Manual 15kV KVAN-1125M 1200/2000A Maxi-Vac Medium-Voltage Vacuum Circuit Breaker Circuit Breaker Sales, Inc. 1315 Columbine Drive Gainesville, TX 76241 (940) 665-4444 Revision 2 March 2012

More information

Ex. 1-1 Nacelle Familiarization and Safety Discussion

Ex. 1-1 Nacelle Familiarization and Safety Discussion Exercise 1-1 Nacelle Familiarization and Safety EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with key components and safety aspects of the nacelle trainer. You will be

More information

Michigan State University Construction Standards SECONDARY UNIT SUBSTATIONS PAGE

Michigan State University Construction Standards SECONDARY UNIT SUBSTATIONS PAGE PAGE 261116-1 SECTION 261116 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

ALTERNATOR STARTUP Turning gear to full operation. Procedure initiated by:. 7/03 Before starting procedure, remove all check marks.

ALTERNATOR STARTUP Turning gear to full operation. Procedure initiated by:. 7/03 Before starting procedure, remove all check marks. ALTERNATOR STARTUP Turning gear to full operation. Procedure initiated by:. 7/03 Before starting procedure, remove all check marks. 1. Check log book for incomplete compliance for further operation. 2.

More information

CAL/OSHA ELECTRICAL LOW VOLTAGE

CAL/OSHA ELECTRICAL LOW VOLTAGE Preparation: Safety Mgr Authority: CEO Issuing Dept: Safety Page: Page 1 of 7 Purpose The purpose of this program is to prevent injuries due to electrical exposure to low voltage (less than or equal to

More information

When: Task: See job aid:

When: Task: See job aid: On opening Wake minilab from Sleep mode page 2 of Maintenance Schedule Resolve errors or warnings on touchscreen Check supplies and long-life consumables status Check pen health and verify image quality

More information

Service Manual for Battery Control Center

Service Manual for Battery Control Center Service Manual for Battery Control Center P/N 82 E0071 00 (Ref. 81 1317) June, 1999 Battery Control Box Operation Charging Circuit This function charges the coach battery from the engine alternator while

More information

Building Operator Certification Level I

Building Operator Certification Level I Building Operator Certification Level I A Partnership of the CUNY Institute for Urban Systems Building Performance Lab, the CUNY School of Professional Studies, and the New York State Energy Research &

More information

ALTERNATOR PRECAUTIONS. Some precautions should be taken when working on this, or any other, AC charging system.

ALTERNATOR PRECAUTIONS. Some precautions should be taken when working on this, or any other, AC charging system. The alternator charging system is a negative (-) ground system which consists of an alternator, a regulator, a charge indicator, a storage battery and wiring connecting the components, and fuse link wire.

More information

Best Diversified Products, Inc. Product Manual. BestReach Rigid Belt. Models BRB 230 OS BRB 230 SS BRB 460 OS BRB 460 SS

Best Diversified Products, Inc. Product Manual. BestReach Rigid Belt. Models BRB 230 OS BRB 230 SS BRB 460 OS BRB 460 SS Best Diversified Products, Inc. Product Manual TM BestReach Rigid Belt Models BRB 230 OS BRB 230 SS BRB 460 OS BRB 460 SS Best Diversified Products Inc. 107 Flint Street Jonesboro, AR 72401 Phone 870-935-0970

More information

BP-Husky Refinery Toledo, OH

BP-Husky Refinery Toledo, OH BP-Husky Refinery Toledo, OH Document Type: Procedure Refinery Wide Procedure No.: SAF 095 Effective Date: 2/25/16 Owner: D. Clark Working on or near Energized Electrical Equipment Rev. No.: 6 Auth. By:

More information

Wind and Temperature Tip Over Hazard Do not add notice boards or similar

Wind and Temperature Tip Over Hazard Do not add notice boards or similar Lift & Work Platform Safety Information Safety Information: Boom Lifts Safety Information: Scissor Lifts Safety Information: Boom Lifts Power Lines Electrocution Hazard Maintain safe clearance from Electrical

More information

CRANE & HOIST SAFETY PROGRAM

CRANE & HOIST SAFETY PROGRAM CRANE & HOIST SAFETY PROGRAM 1.0 PURPOSE The purpose of the Crane and Hoist Safety Program is to: 1.1 Ensure a safe work environment for employees who operate, maintain, or work around cranes and hoists

More information