Lionel Burning Switch Tower Owner s Manual

Transcription

1 /08 Lionel Burning Switch Tower Owner s Manual

2 Congratulations on your purchase of the Lionel Burning Switch Tower! s the building smokes, a man waves for help on the balcony. nother figure travels up and down the stairs with a bucket of water. Caution! dd smoke fluid before you operate this accessory. Inventory of parts Burning Switch Tower Smoke fluid Four green wires Owner s manual Two separate switches Table of contents Powering the accessory 3-4 Operating the accessory 4 dding smoke fluid 5 Operating the accessory in the TrainMaster Command Control environment 5-6 Replacing the lamps 7 Limited Warranty/Lionel Service 8 The following Lionel marks may be used throughout this instruction manual and are protected under law. ll rights reserved. Lionel, TrainMaster, Odyssey, RailSounds, CrewTalk, TowerCom, DynaChuff, StationSounds, Pullmor, ElectroCoupler, Magne-Traction, CB-1 Remote Controller, PowerMaster, Lionel ZW, ZW, PowerHouse, TMCC, Lionelville, Lockon, Wireless Tether, LionMaster, FatBoy, merican Flyer, TrainSounds, PowerMax, LEGCY, PowerMax Plus The name FasTrack is used with permission from Pitsco, Inc. 2

3 Powering the accessory Your accessory was designed to operate at volts (C). You may choose to supply power with a separate accessory power supply or through the track using a Lionel Lockon (available separately, ) or a FasTrack ccessory Power Wire (available separately, ). Refer to Figure 1. To make the proper connections, the ends of the wires must be stripped back 1/8 to 1/4. Caution! Only an adult should perform this task. We recommend using a pair of wire strippers. lways use care when stripping wires. 1. ttach one wire to the C INPT terminal on the underside of the accessory and connect it to the Common/Ground/ terminal on your power supply or to the #2 Lockon terminal. If you are using the FasTrack ccessory Power Wire, twist the accessory wire to the ccessory Power Wire, which must be attached to the track. We recommend using a wire nut (not included) to insulate the connections. Note! To make the spring clip terminal connection, press down on the top portion of the spring clip so that the metal loop is exposed. Slide the bare end of the wire into the loop, then release pressure on the spring clip. 2. ttach a wire to the remaining C INPT terminal on the underside of the accessory and connect it to the Power/ terminal on your power supply or to the #1 Lockon terminal. If you are using the FasTrack ccessory Power Wire, twist the accessory wire to the remaining ccessory Power Wire. 3. ttach a wire to the CTION terminal on the underside of the accessory and connect it to a separate switch. Connect the remaining switch terminal to the Power/ terminal on your transformer, the #1 Lockon terminal, or a FasTrack ccessory Power Wire. Note! To make the switch connection, loosen the screw, wrap the wire around the screw clockwise, and tighten the screw to secure the connection. 4. ttach a wire to the LIGHT terminal on the underside of the accessory and connect it to the second separate switch. Connect the remaining switch terminal to the Power/ terminal on your transformer, the #1 Lockon terminal, or a FasTrack ccessory Power Wire.

4 Powering the accessory (continued) OR OR POWER SPPLY Lockon FasTrack ccessory Power Wire Figure 1. Power connections Operating the accessory se the two separate switches to operate the accessory. The switch connected to the LIGHT terminal turns on the lights and smoke unit. The switch connected to the CTION terminal turns on the movement of the figures. Caution! dd smoke fluid before you operate this accessory to avoid damaging the smoke unit. 4

5 dding smoke fluid Your accessory is equipped with an operating smoke unit that creates safe, clean, white smoke. You must periodically add about five drops of smoke fluid while the accessory is operating. Operating the smoke unit without a small amount of smoke fluid will cause damage to the smoke unit. Your accessory includes a small bottle of smoke fluid. To add smoke fluid, press down and unscrew the smoke fluid bottle s cap, then use a pin to pierce the tip of the nozzle. Lift away the roof and add about five drops of smoke fluid into the hole. Refer to Figure 2. Replace the roof. Figure 2. Smoke fluid Operating the accessory in the TrainMaster Command Control environment For operation in the TrainMaster Command Control environment, you may choose to wire this accessory with an SC-2 Switch and ccessory Controller (available separately, ) or the ccessory Switch Controller (available separately, ). Refer to these manuals for additional information. SC-2 wiring and operation Refer to Figure 3 to connect your accessory to the SC-2 and a separate accessory power supply. Example: CC2 X2 turns on lights CC2 X1 (hold) activates tower while button is pressed. CC2 X 2 turns lights off. CC1 CC2 CC1 CC2 ction Lights Control lights with CC2 X2 mechanism with CC2 X1 Figure 3. SC-2 connections 5

6 Operating the accessory in the TrainMaster Command Control environment (continued) SC wiring and operation Refer to Figure 4 to connect your accessory to the SC and a separate accessory power supply. Example: CC1 X2 toggles lights on and off. CC2 X1 (hold) activates the animation. ction Lights Bottom of the accessory Figure 4. SC connections

7 Replacing the lamps Three lamps illuminated the interior of this accessory. During the course of normal operations, you may find that the lamps require replacement. Replacement lamps are available at your authorized Lionel Service Center or from Lionel Service in Chesterfield, Michigan. Refer to Figure 5 as you replace the lamps. To replace the lamp on the second floor, simply lift away the roof, pull the expired lamp out of the socket, and install the replacement (Lionel part no. 6SP ). Replace the roof. To replace a lamp on the ground floor, remove the four screws from the underside of the base. Locate and remove the expired lamp, then install the replacement (Lionel part no. 6SP ). Replace the base, securing it with the four screws. Figure 5. Lamp replacement 7

8 Limited Warranty/Lionel Service This Lionel product, including all mechanical and electrical components, moving parts, motors and structural components, except for light bulbs, is warranted to the original consumer-purchaser, for one year against original defects in materials or workmanship when purchased through an authorized Lionel merchant. This warranty does NOT cover normal wear and tear, light bulbs, defects appearing in the course of commercial use, or damage resulting from abuse or misuse of the product by the purchaser. Transfer of this product by the original consumer-purchaser to another person voids this warranty. Modification of this product voids this warranty. ny warranted product which is defective in original materials or workmanship and is delivered by the original consumer-purchaser to Lionel L.L.C. or an authorized Lionel L.L.C. Service Center, together with proof of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the original purchase price will be granted. ny products on which warranty service is sought must be sent freight or postage prepaid, as transportation and shipping charges are not covered by the warranty. In no event shall Lionel L.L.C. be liable for incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may have other rights which vary from state to state. Instructions for Obtaining Service If service for this Lionel L.L.C. product is required, bring the item, along with your dated sales receipt and completed warranty information to the nearest uthorized Lionel Service Center. Your nearest Lionel Service Center can be found by calling Lionel, or by accessing our Website at If you prefer to send your product back to Lionel L.L.C. for repair in Michigan, you must first call or FX , or write to Customer Service, P.O. Box 748, New Baltimore, MI , stating what the item is, when it was purchased and what seems to be the problem. You will be sent a return authorization letter and label to ensure your merchandise will be properly handled upon receipt. Once you have received your return authorization and label, make sure that the item is packed to prevent damage during shipping and handling. We suggest that you use the product s original packaging. This shipment must be prepaid and we recommend that it be insured. Please make sure you have followed all of the above instructions carefully before returning any merchandise for service. You may choose to have your product repaired by one of our uthorized Lionel Service Centers after its warranty has expired. reasonable service fee will be charged. Warranty Information Please complete the information below and keep it, along with your dated sales receipt. You must present this and your dated sales receipt when requesting warranty service. Name ddress Place of Purchase Date of Purchase Product Number Product Description 2008 LIONEL L.L.C., CHESTERFIELD, MI NITED STTES OF MERIC PRINTED IN CHIN