KTM Motorcycle 1050/1190/Super Duke
|
|
- Jack Page
- 6 years ago
- Views:
Transcription
1 1/21/2016 Brandon Distributing, Inc KTM Motorcycle 1050/1190/Super Duke AP 900cm Doc#1191 Installation Guide With OBD Connector
2 Parts included in this kit RS Switch Custom OBD Harness Custom KTM Motorcycle Harness for Trail Tech Switch (3pieces) Custom KTM Motorcycle Installation Guide Custom Throttle Harness Smart Line AP900cm Module The following is a complete step by step installation guide for the Smart Line AP900cm Cruise Control. KTM Motorcycle 1050/1190/Super Duke Please read each step carefully before you start the install to insure no damage is done to the Motorcycle.
3 The first step in installing the Smart Line AP900cm cruise control on your KTM motorcycle is to decide the location that you would like to mount the cruise control module and the cruise control switch. On the KTM 1190R Model a good location for the cruise control module is under the Left side cover of the motorcycle. On the KTM 1190S model a good location for the cruise control module is under the passenger seat between the frame rails. You can mount the unit upside-down using the mounting tabs to secure the cruise control module to the frame. On the KTM 1290 Super Duke a good location is under seat. *Temporarily mount your Smart Line AP900CM module into position.
4 INSTALLATION of THROTTLE HARNESS 1. Disconnect the negative side of the battery located under the seat of the motorcycle. 2. Remove the Fuel Tank. 3. Remove the Left Side Air Intake Tube 4. Locate the OEM Throttle Harness Connector. 5. Unplug the OEM Throttle Harness Connector. (see below picture)
5 6. Plug in the Throttle Harness ( ) from Cruise Control kit to both ends on the OEM Throttle Connections. 7. Reinstall the left side Air Intake Tube. 8. Route the Throttle Harness wiring over the Intake Tube and back to the Smart Line AP900cm Control Module.
6 INSTALLATION of OBD CONNECTOR 1. Locate the OBD connector under the seat of the motorcycle. 2. Plug the OBD connector into the OBD plug. 3. Route the wire from the OBD connector to the Smart Line AP900cm module.
7 Mounting & Wiring Harness for Trail Tech Switch 1. There are two places to mount the Trail Tech switch. 2. Location 1 is between the mirror bracket and the turn signal. (This is the easier of the 2 locations to mount the switch.)
8 3. Location 2 is between the Turn signal and the left Hand Handle Bar Grip. 4. Carefully loosen the mounting bolt on the underside of the turn signal switch and slide the switch to the right about ½ inch. 5. Mount the Trail Tech switch Part number 8500-RS to the handle bar. 6. Once the Trail Tech switch is mounted tighten to 1.5 foot pounds. 7. Route the Custom harness back to the Smart Line AP900cm module. Reconnect the negative side of the battery Remember that a neat & clean install does count. Now is a good time to check your work. Make sure all of the Smart Line AP900cm cruise control wires are securely mounted all the way back to the control module. *Continue on next page
9 THROTTLE POSITIONING PROGRAMMING It is required on all motorcycles to program the throttle positioning to the cruise control system for optimal operation of the system. 1. Turn ignition switch to the ON position, DO NOT start motorcycle. 2. Turn cruise control on. (center button) Top = SET Center = On/Off Bottom=Resume 3. Press and hold the Brake, then press SET (top button) 4 times. You will hear 4 beeps. Continue to hold the brake for the next step. 4. Press RESUME (bottom button) 1 time. You will hear 1 low beep. Release the brake and you will hear 1 high beep. You are now in the pedal set-up mode. Press SET (top button) 1 time and release to learn the values of the throttle in the idle position. You will hear 1 high beep. 5. Twist the throttle grip to full throttle, once at full throttle, Press resume (bottom button) to store the throttle position signal outputs. You will hear 1 high tone beep. Slowly release the throttle grip and it should keep sounding low tone beeps. Release the Throttle Grip completely. 6. Press and hold the brake, then press set (top button) 4 times you will hear 1 long beep. Then turn the Motorcycle off. 7. The Throttle positioning signals are now stored in the cruise control module. Congratulations! You have now completed the install of the Smart Line AP900cm Cruise Control For your KTM Motorcycle. Take your Motorcycle out for a test drive. The information included in this installation guide, has been compiled through manufacturer s service manuals, research and actual motorcycle testing. We try to have the most accurate and up-to-date information. However, as motorcycles change in design we cannot guarantee the accuracy of all information. ** It is the installers responsibility to verify the wire colors and signals prior to attaching and after installing this product. Incorrect connection of wires may cause motorcycle or accessory malfunctions or even damage to components, which could become a major risk factor, causing an accident or injury while driving, to you, a passenger and/or another motorist. * We shall not be held responsible for the use of this information, misuse or any typographical errors. We shall not be held Responsible for damage to vehicle/motorcycle or injury to its occupants caused by the use of information in this installation guide.
10 CRUISE CONTROL FINE TUNING ADJUSTMENTS Always adjust the Init 1 st before the Gain INIT Speed Adjustments Low System INIT :is distinguished by sluggish throttle response when pressing the Set key to engage the cruise control. The result is a drop in speed which then returns to set speed. High System INIT: is distinguished by overshooting of the set speed. To enter the adjustment mode follow the following steps. 1. Start the motorcycle. 2. Turn the cruise control on. 3. Press and hold your brake and continue to hold until you are instructed to release it. 4. Press the set button four times. You will get 4 beeps from the cruise control. 5. Press the resume button three times. 6. Release the brake. You will hear 3 Hi tone beeps. 7. Drive the motorcycle to a convenient speed. 8. Press the set button. 9. If the cruise control drops speed as you press the set button this is the adjustment you will make. To increase the init speed, press the set button and release. This will increase the amount of time it takes to engage the cruise control. If the cruise control overshoot s the set speed this is the adjustment you will make. To decrease the init speed, press the Resume button and release. This will decrease the amount of time it takes to engage the cruise control. You can continue to do these adjustments until you feel that the cruise control is responding as you like. 10. When the cruise control response has been adjusted to a satisfactory level. 11. Press the set button 4 times and you will hear 1 long beep. This will confirm and save the adjustments that you have made.
11 CRUISE CONTROL FINE TUNING ADJUSTMENTS Always adjust the Init 1 st before the Gain Gain Adjustments Low System Gain: is distinguished by sluggish throttle response when traveling up or down a hill. Excessive overshoot of the final set speed. High System Gain: is distinguished by overactive speed adjustments and excessive throttle motion or surging. To enter the adjustment mode follow the following steps. 1. Start the motorcycle. 2. Turn the cruise control on. 3. Press and hold your brake and continue to do this until you are told to release it. 4. Press the set button four times. You will get 4 beeps from the cruise control. 5. Press the resume button four times. 6. Release the brake. You will hear 4 Hi tone beeps. 7. Drive the motorcycle to a convenient speed. 8. Press the set button 9. If you have Excessive throttle motion (surging) this means that your gain is set to high. To lower your gain press and release the resume button. Every time that you press the button it will lower your gain. Once you are happy with the throttle settings, go to the side of the road and press and hold the brake, press set 4 times and you will hear 1 long beep, the cruise control has learned the new settings. If you have Excessive overshooting gain is set to low (this is when you press the set button and it speeds up and then it sets) Press the set button, turn off the cruise control and retry to set. Continue doing this until the cruise control no longer overshoots the set speed. Once you are happy with the throttle settings, go to the side of the road and press and hold the brake, press set 4 times and you will hear 1 long beep, the cruise control has learned the new settings.
12 Help Spread the News We would love for you to share your comments and pictures. The install you did using our Smart Line Cruise Control. Pictures of the New Adventures you ve taken since installing the Smart Line Cruise Control. Get your Bragging Rights Click on our Face Book Link and start your Bragging Rights. Have a Great Day Enjoying a comfortable and relaxing ride, particularly while on a long trip.
CRUISE CONTROL SPEED LIMITER. SL900Series. Dealer address details: C Rev. 7.0
INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series Dealer address details: 35 231.000453C Rev. 7.0 1 2 NOTES: CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics
More informationCRUISE CONTROL SPEED LIMITER Rev. 4.0
INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series 231.0004530 Rev. 4.0 1 2 CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics module location... 5 4 Input
More informationCRUISE CONTROL SPEED LIMITER
Dealer address details: 39 INSTALLATION MANUAL CRUISE CONTROL & SPEED LIMITER AP900Ci SL900CiSeries 231.0005060 Rev. 1.0 f FOREWORD: This installation manual is written for installers with knowledge of
More informationTABLE OF CONTENTS PARTS LIST
TROUBLESHOOTING: Note: You will have a check engine light and/or other problems unless using this product with a compatible ECM calibration. Contact your tuning supplier to learn whether or not aftermarket
More informationTIP SHEET RS + EVO ALL + T Harness Remote Starter for Kia Optima 2016
TIP SHEET RS + EVO ALL + T Harness Remote Starter for Kia Optima 2016 Thank you for purchasing your remote start from MPC - an industry leader in providing remote starts to do-it-yourself installers since
More informationPlease contact BrakeAway Products tech support for additional (503) or
Congratulations on the purchase of your new BrakeAway Motorcycle Cruise Control. At BrakeAway Products, we are committed to your complete satisfaction. With proper installation, use, and periodic maintenance,
More informationCruise Control designed. The only. and developed in Australia CRUISE CONTROL OPERATING INSTRUCTIONS. PROFESSIONAL SERIES and DRIVE by WIRE
The only Cruise Control designed and developed in Australia CRUISE CONTROL OPERATING INSTRUCTIONS PROFESSIONAL SERIES and DRIVE by WIRE CONGRATULATIONS! You have purchased one of the most advanced cruise
More informationTIP SHEET. STEP 1: Starting the installation
TIP SHEET Add on Remote Start Kit for Push to Start CRV 2015-2016 Txxxx Thank you for purchasing your remote start from MPC - an industry leader in providing remote starts to do-it-yourself installers
More informationApplication(s) > Items Supplied > Instruction Manual >
301 E. La Palma Ave., Yorba Linda, Ca 97 Ph. 714.69.10, Fax. 714.69.5016 Items Supplied > Application(s) > www.fi000r.com 1 Fi000R Fuel Injection Module Zip Ties 1 Velcro Strip Oxygen Sensor Eliminators
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationINSTALLATION MANUAL AP60B INSTALLATION MANUAL
INSTALLATION MANUAL 2. TOOLS REQUIRED The following is a list of tools required to properly install the cruise control. While this unit may be installed without some of the tools listed, it is recommended
More information2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions
2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationSpeed Sentinel Programmable Road Speed Limiter
An ISO 9001:2008 Registered Company Speed Sentinel Programmable Road Speed Limiter SS531-A, SS531-AX, SS531-AND Ford E Series 2005-2012 Ford F Series 2008-2010 Ford Crown Victoria 2005-2008 Contact InterMotive
More informationBASIC TROUBLE SHOOTING (PERFECTPASS FOR MECHANICAL ENGINES) How PerfectPass Works
BASIC TROUBLE SHOOTING (PERFECTPASS FOR MECHANICAL ENGINES) How PerfectPass Works Through the in-dash display the driver sets the desired boat speed or engine RPM depending upon which mode of operation
More informationRCA PLUG KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RCA PLUG KIT P/N 2883824 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationBrakeAway Products Inc. wishes you many years of cramp free cruising, ENJOY and ride SAFELY!!!
Congratulations on the purchase of your new BrakeAway Motorcycle Cruise Control. At BrakeAway Products, we are committed to your complete satisfaction. With proper installation, use, and periodic maintenance,
More informationHANDLEBAR BAG WITH PHONE CHARGER KIT
HANDLEBAR BAG WITH PHONE CHARGER KIT P/N 2883687; 2883786 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted
More informationTABLE OF CONTENTS. If you have any questions during the installation of this product, please H&S Motorsports support at
TROUBLESHOOTING: Note: You will have a check engine light and/or other problems unless using this product with a compatible ECM calibration. Contact your tuning supplier to learn whether or not aftermarket
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationMK7 GTI Electronic Folding Mirror Conversion
MK7 GTI Electronic Folding Mirror Conversion 01 Mirror and Switch Installation 1. Using a soft pry tool remove the trim panel on the driver side door handle. 02 2. Remove 2 T-30 torx screws. 03 3. On the
More informationEdelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179
For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your vehicle.
More informationCRUISE CONTROL SPEED LIMITER. SL900Series. Dealer address details: Rev. 3.0
USER GUIDE f CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series Dealer address details: 11 231.0005010 Rev. 3.0 1 2 CONTENTS: 1 Product variants... 2 2 Cruise Control Safety Features. 3 3 Operating
More informationSpeed Sentinel II Programmable Road Speed Limiter
An ISO 9001:2008 Registered Company Speed Sentinel II Programmable Road Speed Limiter SS501-A, SS501-AX Ford E Series 2005-2008 Ford F250-F550 Series 2008-2010 Ford Crown Victoria 2005-2008 Contact InterMotive
More informationFog Lamp Instructions
Fog Lamp Instructions 2011+ Ford Super Duty Congratulations on your purchase of a high quality PUTCO product. Should you need any application or technical assistance feel free to call us at: 1-800-247-3974
More informationFront Door Panel: Service and Repair Front Door Trim Panel - Removal
Front Door Panel: Service and Repair Front Door Trim Panel - Removal REMOVAL Special Tools: 1. Disconnect and isolate the negative battery cable 2. Using trim stick or equivalent, disengage the two retaining
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationPlease make sure you pay close attention to any details in this manual for instructions on proper maintenance and overall usage of our product.
NEW YORKER LAB Introduction Please always remember to wear an approved safety helmet and other safety gear when operating this electric bicycle. Make sure you comply with all road regulations and any local
More informationPart A. A1 Introduction. AP-550 Installation Manual. Installation manual. for the universal. AP-550 GoldCruise
AP-550 Installation Manual Installation manual for the universal AP-550 GoldCruise Part A A1 Introduction The GoldCruise is an optimal flexibility product which consists of a universal part and a specific
More informationElectronic Over-Boost Protection System With Vent-to-Atmosphere Valve Control And 4 Bar Map Sensor Output Installation and User Guide
Stratified guardian angel v3 Electronic Over-Boost Protection System With Vent-to-Atmosphere Valve Control And 4 Bar Map Sensor Output Installation and User Guide Guardian Angel V3 Installation and User
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 23302 2002 MDX Issue Date PN 08U97-S3V-210 (BLACK) P/N 08U97-S3V-270 (SADDLE) NOV 2001 PARTS LIST Wood trim steering wheel 1. Make sure
More informationFitting instructions for Voodoo Fairing - KTM 950/990 Adventure
Fitting instructions for Voodoo Fairing - KTM 950/990 Adventure Thank you for purchasing the Voodoo fairing. Your fairing kit comes largely completed and includes the following. 1 x Fairing 1x Screen,
More informationAccessory Fitting Instructions
Accessory Fitting Instructions Heated Grip Kit Kit Number Models Affected A9680 Street Twin, Street Cup from VIN 8750 A9680 Street Cup to VIN 879 A9685 Street Scrambler A9685 Thruxton 00 R A9689 Thruxton
More information1200 Southeast Ave Tallmadge, Ohio to 2014 Mustang (V6 & V8) Summit Racing Roll Stop Install Instructions.
1200 Southeast Ave Tallmadge, Ohio 44278 2010 to 2014 Mustang (V6 & V8) Summit Racing Roll Stop Install Instructions Part # SUM-760005 Thank you for considering the Summit Racing Roll Stop. Summit Racing
More informationSP EVO-CHR4 (A)
TIP SHEET Installation Tips for SP-502 + EVO-CHR4 (A) Remote Start / Alarm T1630 Chrysler 300 (2008-2011) Dodge Magnum (2008) Chrysler Town and Country (2008-2015) Dodge RAM (2009-2012) Dodge Challenger
More informationFUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit with Adjustable Slave Cylinder INSTALLATION & USER S GUIDE Doc ID: 191-7704A Doc Rev: 102915 OVERVIEW This kit replaces the OEM core clutch components including
More informationVolkswagen MKVI Jetta w/keyless Start Traction Control Button Retrofit Kit Installation Instructions
Volkswagen MKVI Jetta w/keyless Start Traction Control Button Retrofit Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationFLOWMASTER XDR PN DELTA BOOST PERFORMANCE TUNER INSTALLATION INSTRUCTIONS for Can Am Maverick X3
FLOWMASTER XDR PN DELTA BOOST PERFORMANCE TUNER INSTALLATION INSTRUCTIONS for 2017 2018 Can Am Maverick X3 Thank you for choosing the Flowmaster XDR Delta Boost Performance Tuner! We have invested many
More informationw w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required
-J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.
More informationSeat Comfort Systems
Seat Comfort Systems Revitalizer Massage Installation Manual SCS6MC Seat Comfort Systems www.seatcomfort.com Important Safety Instructions The Reviltalzer Massage System is a vibration system that has
More informationInstallation Instructions
This product has been designed and manufactured to work correctly with installation as described in these instructions. Failure to follow these instructions could result in damage to property, damage to
More informationGENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS
GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationEdelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines Part #7179
For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 24570 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2003 MDX Issue Date OCT 2002 PARTS LIST Wood steering wheel 1. Make sure
More informationGW-CRUISE Cruise Control Vanagon [84-91]
Driving without cruise control on a long trip can be tiring. Update your vehicle with some modern convenience with this easy to install cruise control kit. Tools Needed Phillips screwdriver #2 Electric
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationInstruction Manual. Backup Camera System For Pickup Trucks. RVS-Pickup
Instruction Manual Backup Camera System For Pickup Trucks RVS-Pickup Rear View Safety, Inc. 2016 1 NOTE! Please read all of the installation instructions carefully before installing the product. Improper
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST 2006-2007 Yamaha R6 Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol swab 1 Posi-tap THE IGNITION
More informationTIP SHEET. Step 1: Prepare the Vehicle
TIP SHEET Installation Tips for LC + EVO-CHR4 (C) Remote Start Kit Pre-wired Txxxx Chrysler 300 (2011) Chrysler Town and Country (2011-2015) Dodge RAM (2011-2012) Dodge Challenger (2011-2014) RAM CV (2011-2016)
More informationFuel Injection System
7. Fuel Injection System XCITING 400i Fuel Injection System This chapter covers the location and servicing of the fuel system components for the KYMCO XCITING 400i. Air box... 7-2~7-5 Fuel Tank... 7-6~7-10
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationINSTRUCTIONS. #82028 Diesel Nitrous System. Thank you for choosing ZEX products; we are proud to be your manufacturer of choice.
1 INSTRUCTIONS #82028 Diesel Nitrous System Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. Why our nitrous system is better: 2 Performance enthusiasts know the potential
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25831-26975 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2004 MDX Issue Date MARCH 2004 PARTS LIST Wood steering wheel 1. Make
More informationTable of Contents. 4 Getting Started 4 About the Juice 5 Safety Terms 5 Product Registration 6 Important Notes 7 Truck Orientation
Table of Contents 4 Getting Started 4 About the Juice 5 Safety Terms 5 Product Registration 6 Important Notes 7 Truck Orientation 8 Juice Installation 1999-2003 (7.3L) 8 Supplied Items & Required Tools
More information200-4R TRANSMISSION LOCK-UP HARNESS INSTALLATION INSTRUCTIONS
2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech E-mail: painless@painlessperformance.com Web: www.painlessperformance.com 60110 200-4R
More informationEnglish. Fitting Instructions: Sprint GT 1050 A and A of 12
English Fitting Instructions: Sprint GT 050 A950855 and A950856 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's use of proven engineering, exhaustive
More information1) Remove battery so that you have access to the firewall behind the battery. Also remove the under hood fuse box cover.
Thank you for purchasing SacCityCorvette s Hardwire CoolIt CoolIt H2 and H3 Installation Instructions (v10/14) IMPORTANT! We highly recommend that you test your CoolIt H2/H3 for compatibility and operation
More informationJEEP TJ INSTALL GUIDE
JEEP TJ INSTALL GUIDE S-TECH Switch Systems DEVELOPED, DESIGNED, MANUFACTURED and Assembled in the Rocky Mountains of Colorado, known to many as JEEP COUNTRY. Trail riding at 10,000 feet at night requires
More informationAP500 FAULT FINDING NEW INSTALLATION
AP500 FAULT FINDING NEW INSTALLATION This Bulletin covers the AP500 model which is identified by a black plastic Electronic Module with a silver printed label. This module would normally be mounted behind
More informationInstallation Instructions JMS PedalMAX Kit P/N PX GM GM Drive-By-Wire Electronic Throttle Enhancement Device
Installation Instructions JMS PedalMAX Kit P/N PX-5000-1415GM 2013-2015 GM Drive-By-Wire Electronic Throttle Enhancement Device Included in the PedalMAX kit: (1) PedalMAX assembly (1) 4-pin RED de-sensitizing
More informationINSTALLATION GUIDE. z-start Revision RMS200 Perch Adjuster Manual Revision:
REKLUSE MOTOR SPORTS z-start Perch Adjuster INSTALLATION GUIDE z-start Revision 3.000 RMS200 Perch Adjuster 194-200 Manual Revision: 121906 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43
More informationAMS F1-I INTAKE MANIFOLD
AMS F1-I INTAKE MANIFOLD The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS will never compromise
More informationHarley Davidson V-Rod Models
2801190 REV. 8-11-05 User Manual 2002-2005 Harley Davidson V-Rod Models Part Number DFCH-5 Congratulations on your purchase of this Dynatek product. Please take a moment to read these instructions completely
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS QUICK SHIFTER P/N 08U70-MKJ-D00 CB1000RA Honda Dealer: Please give a copy of these instructions to your customer. MII 16775 Issue Date August
More informationM7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301
M7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301 M7 Speed engineers and manufactures the highest quality MINI COOPER accessories and performance parts available anywhere on Planet Earth! Please
More informationC&L Upper Intake Plenum (96-04 GT):
C&L Upper Intake Plenum (96-04 GT): Tools Needed: Flat-Head Screwdriver 10mm Socket 5/16 Socket 1/4 or 3/8 Ratchet 2 Ratchet Extension Time Required: Approximately 1 hour Installation Instructions: 1.
More informationINSTALLATION GUIDE. Doc ID: C Doc Rev:
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit INSTALLATION GUIDE Doc ID: 191-7700C Doc Rev: 012213 2012 Rekluse Motor Sports Rekluse Motor Sports, Inc. 12000 W Franklin Rd Boise, Idaho 83709 208-426-0659
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationCruise control On Board Diagnostic (OBD)
Page 1 of 13 01-203 Cruise control On Board Diagnostic (OBD) Special tools, test equipment and auxiliary items VAS5051 Diagnostic Operation Center (DOC) and/or VAG1551 Scan Tool (ST). VAG1551/3 adapter
More informationInstallation Instructions Diesel Nitrous System (#82028)
Installation Instructions Diesel Nitrous System (#82028) Thank you for choosing ZEX. If at any time you have questions regarding this or any of our products, please call our Nitrous Help support line at
More informationAvoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket.
HOUSINGS 7808 Thank You For Choosing Küryakyn! Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding
More informationI N S T A L L A T I O N G U I D E
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Ford Super Duty - Crew Cab 2008-2010, 2013-2015 77134-01A Note:The application works only on the Crew Cab model Vehicles. INSTALLATION TIME 3-5
More informationBBK Long Tube Header and Shorty Mid-pipe (05-10 GT):
Time Required: Approximately 6-8 Hours BBK Long Tube Header and Shorty Mid-pipe (05-10 GT): Tools Required: Floor Jack or Ramps Jack Stands (unless you used a ramp) 5mm, 8mm, 10mm, 12mm, 22mm sockets/open
More informationInstruction Manual. Backup Camera System With Replacement Mirror Display RVS N
Instruction Manual Backup Camera System With Replacement Mirror Display RVS-778718N Rear View Safety, Inc. 2016 1 NOTE! Please read all of the installation instructions carefully before installing the
More informationKTM 690 TTV UPGRADE INSTRUCTIONS
INSTRUCTIONS: Temp. Sensor Connector/Jumper Jumper Plug O-Ring TTV STEP 1 Remove the seat, radiator shrouds and air box from the bike and drain the coolant system by removing the drain bolt on the water
More informationPage No General Installation Wiring diagram AP Wiring diagram AP Tools required...5. Parts list AP Parts list AP250...
INSTALLATION SECTION Page No General Installation Wiring diagram AP150...3 Wiring diagram AP250...4 Tools required...5 Parts list AP150...6 Parts list AP250...8 Installation instruction Vacuum actuator
More informationTOYOTA PRIUS 2010 TVIP V5 PREPARATION
PREPARATION Part #: PT398-47090 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information2017 Current Ford SuperDuty HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford SuperDuty HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationAutomotive FORENZA / RENO October 6, 2014 Technical Service Bulletin Engine Bulletin No. TS R1
Service Automotive FORENZA / RENO October 6, 2014 SUBJECT: MODEL(S): YEAR: Revisions: Throttle Position Sensor Replacement Forenza (RQ420) Reno (RQ420) 2006 2008 Forenza 2006 2008 Reno R1-10/08/14. This
More informationMustang One-Touch Convertible Top Module (2005+) - Installation Instructions
Mustang One-Touch Convertible Top Module (2005+) - Installation Instructions The below installation instructions work for the following products: Mustang One-Touch Convertible Top Module (2005+) Please
More informationEFI Harley Davidson 1340 EVO
Floppy Disc Request Form If you do not have a CD-Rom drive and would like to receive the program and the alternate maps for your model on a 3 1/2 floppy disc, please fax this form to Dynojet at 1-702-399-1431
More informationU S A INSTALLATION GUIDE EP400 / E8-B
U S A INSTALLATION GUIDE EP400 / E8-B www.easycar-.com Before Beginning the Installation 1. Wire Connection Guides Please read this entire installation guide before beginning the installation. The installation
More informationPACKAGE CONTENTS
Thank you for purchasing the Electronic Jet Kit (EJK) from Dobeck Performance. This EFI controller is designed to be used on stock or modified vehicles. The following instructions will walk you through
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
2014 FORD TRANSIT FULL SIZE PART NUMBER: 250-9636 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD TRANSIT 150, 250 RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT
More informationJHP 04 GTO SPORTS BINNACLE KIT INSTALL GUIDE
JHP 04 GTO SPORTS BINNACLE KIT INSTALL GUIDE NOTE: If you don't feel comfortable with any of the following steps, you should find a professional to do the installation. 1) Use a piece of tape as shown
More informationINSTALLATION INSTRUCTIONS PART NUMBER D APPLICATIONS: 2015 W205 Mercedes C W205 Mercedes C450 AMG 2017 W205 Mercedes AMG C43
INSTALLATION INSTRUCTIONS PART NUMBER D440-0057 APPLICATIONS: 2015 W205 Mercedes C400 2016 W205 Mercedes C450 AMG 2017 W205 Mercedes AMG C43 PARTS LIST Qty Part # Description 1 D443-0045 DINANTronics Elite
More informationNOTES: 1489 N THESTA FRESNO, CA PHONE (559) FAX (559)
NOTES: 1489 N THESTA FRESNO, CA. 93703 PHONE (559)486-5444 FAX (559)486-5155 Contents: REMOTE X 2 THIS IS ONLY A GUIDE!!! BUTTON X 16 THE APPLICATIONS SHOWN ARE GENERAL GUIDE LINES OF POSSIBLE APPLICATIONS.
More informationELECTRONIC POSITIVE AIR SHUTOFF
12 January 2015 103675X Electronic positive air shutdown (I-00336) 1 ELECTRONIC POSITIVE AIR SHUTOFF 1036750 2007-2009 Dodge 6.7L 1036751 2010-2015 Dodge 6.7L 1036754 2008-2010 Ford 6.4L 1036755 2011-2014
More informationQUICK FUEL TECHNOLOGY HOT ROD SERIES CARBURETORS SLAYER SERIES CARBURETORS SUPER STREET SERIES CARBURETORS
QUICK FUEL TECHNOLOGY Installation Instructions HOT ROD SERIES CARBURETORS SLAYER SERIES CARBURETORS SUPER STREET SERIES CARBURETORS HR-580-VS 580 CFM Vac. Secondary!!! SS-680-VS 680 CFM Vac. Secondary
More informationHonda Accord/Prelude
Honda Accord/Prelude 1984-1995 In Tank Fuel Pumps TEST 1. Turn the ignition OFF. 2. On the Accord, remove the screws securing the underdash fuse box to its mount. Remove the fuel cut off relay from the
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST 2015 Yamaha FJ-09 Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 3 Velcro strips 1 Alcohol swab 1 Posi-tap 1 O2 Optimizer
More informationBe sure to read and go over all pages before you start your installation
Yamaha Gen-2 V-MaxV Holeshot Superbike Bars Installation Guide Pre-Installation Note Be sure to read and go over all pages before you start your installation Preparation for Installation A) It is recommended
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationEXPANSION TANK MUSTANG GT FORD FIESTA ST PARTS LIST AND INSTALLATION GUIDE PARTS LIST AND INSTALLATION GUIDE
PARTS LIST MMHOSE-MUS8-15L: 4 PC SILICONE HOSES 8 PC CLAMPS 1 PC STAINLESS STEEL ADAPTER MMHOSE-MUS8-15U: 1 PC SILICONE HOSE 1 PC QUICK-DISCONNECT FITTING 1 PC CLAMP MMHOSE-MUS8-15ANC: INSTALLATION INSTRUCTIONS
More informationAUTO-BLiP. User Manual Chevrolet Corvette. Version 1.2
AUTO-BLiP INTELLIGENT DOWNSHIFTS www.auto-blip.com User Manual 1997-2004 Chevrolet Corvette Version 1.2 Copyright 2012 Tractive Technology, LLC. All rights reserved. Page 1 WARNING Use of the AUTO-BLiP
More information850 TETHER SWITCH KIT
850 TETHER SWITCH KIT P/N 2883823 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationKTM TECHNICAL BULLETIN TB 0904 SEPTEMBER 24» 2008
Subject: Checking the Oil Tank Return Pipe Bore KTM TECHNICAL BULLETIN TB 0904 Affected Models: 2006-2007 990 Adventure, Adventure S and Super Duke Initial Information:» Market research has shown that
More informationLOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT
LOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT P/N 2881235; 2881236; 2881237 APPLICATION All AXYS and PRO RIDE chassis with stock Pro-Taper Bar BEFORE YOU BEGIN Read these instructions and
More information