Planting Components. Operator s/parts Manual. Flat Fold Marker. John Deere & 30
|
|
- Lauren Merritt
- 6 years ago
- Views:
Transcription
1 Operator s/parts Manual John Deere & 30 Flat Fold Marker Planting Components! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Cover illustration may show optional equipment not supplied with standard unit. Copyright 2002 Printed 8/8/ M
2 Table of Contents General Information Introduction Using this Manual Important Safety Information Owner s Assistance Operating and Assembly Instructions General Operation & Repair Installation Instructions Hydraulics Adjusting the Hydraulics Maintenance & Lubrication Maintenance Breakaway Protection Marker Transporting Lubrication Troubleshooting Parts Flat Fold Marker Assembly Disk Assembly Hydraulic Assembly Hydraulic Cylinder Sequence Valve Appendix Warranty Copyright 2002 All rights Reserved Great Plains Manufacturing, Inc. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Great Plains Manufacturing, Incorporated Trademarks The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 10/17/ M
3 General Information 1 General Information Important Notice Great Plains Manufacturing, Inc. provides this publication as is without warranty of any kind, either expressed or implied, while every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product at all times in the future. Printed in the United States of America. For your convenience, record your Model and the Date Purchased on page 4. Have this information before you when calling a Great Plains Authorized Dealer. This Operator s Manual applies to the Product Name listed below: Flat Fold Marker for John Deere & 30 10/17/ M
4 2 John Deere & 30 Introduction Great Plains welcomes you to its growing family of new product owners. This Flat Fold Marker has been designed with care and built by skilled workers using quality materials. Proper setup, maintenance and safe operating practices will help you get years of satisfactory use from the machine. Description of Unit The parts on your Flat Fold Marker have been specially designed and should only be replaced with genuine Great Plains parts. Therefore, should your Flat Fold Marker require replacement parts go to your Great Plains Dealer. Using This Manual This manual will familiarize you with safety, assembly, operation, adjustments and maintenance. Read this manual and follow the recommendations to help ensure safe and efficient operation. The information in this manual is current at printing. Some parts may change to assure top performance. Definitions The following terms are used throughout this manual. Right-hand and left-hand as used in this manual are determined by facing the direction the machine will travel while in use unless otherwise stated. IMPORTANT: A crucial point of information related to the preceding topic. For safe and correct operation, read and follow the directions provided before continuing. NOTE: Useful information related to the preceding topic M 10/17/2002
5 Important Safety Information 3 Important Safety Information Look for Safety Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. Be Aware of Signal Words Signal words designate a degree or level of hazard seriousness. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.!! DANGER! WARNING! CAUTION 10/17/ M
6 4 John Deere & 30 Owner Assistance If you need customer service or repair parts, contact a Great Plains dealer. They have trained personnel, repair parts and equipment specially designed for Great Plains products. Your machine s parts were specially designed and should only be replaced with Great Plains parts. Always use the model number when ordering parts from your Great Plains dealer. Record your Model and Date Purchased here for quick reference: Model: Date Purchased: Your Great Plains dealer wants you to be satisfied with your new machine. If you do not understand any part of this manual or are not satisfied with the service received, please take the following actions. 1. Discuss the matter with your dealership service manager. Make sure they are aware of any problems so they can assist you. 2. If you are still unsatisfied, seek out the owner or general manager of the dealership. 3. For further assistance write to: Product Support Great Plains Mfg. Inc., Service Department PO Box 5060 Salina, KS M 10/17/2002
7 Operating and Assembly Instructions 5 Operating and Assembly Instructions Most accidents are the result of negligence and carelessness, usually caused by failure of the operator to follow simple but necessary safety precautions. The following safety precautions are suggested to help prevent such accidents. The safe operation of any machinery is a big concern to consumers and manufactures.your Flat Fold Marker has been designed with many built-in safety features. However, no one should operate this product before carefully reading this Operators Manual. General Operation & Repair Never allow the Flat Fold Marker to be operated by anyone who is unfamiliar with the operation of all functions of the unit. All operators should read and thoroughly understand the instructions given in this manual prior to moving the unit. 1. Make sure safety rules are understood before operating machinery or tractor. 2. Never permit any persons other than the operator to ride on the tractor. 3. Never permit any persons to ride on or stand near the drill while it is in operation. 4. Regulate your speed to the field conditions, maintaining complete control at all times. 5. After repairing or adjusting, make sure all tools and parts are removed from the implement before attempting to operate it. 6. Do not grease or oil machine while it is in operation. 7. Loose fitting clothing should not be worn as it may catch in moving parts. 8. Never dismount from a moving tractor. 9. Do not leave the tractor or the implement unattended with the engine running. 10. Do not stand between the tractor and the implement during hitching. 11. Detach and store implements in an area where children normally do not play. Stabilize implements by using suitable supports and block wheels. 10/17/ M
8 6 John Deere & If a hydraulic leak develops, correct it immediately. Escaping hydraulic oil can have extremely high pressure. A stream of high pressure oil may easily penetrate the skin as with modern needle-less vaccination equipment - but with the exception that hydraulic fluid may cause blood poisoning. It is imperative that the connections are tight and that all lines and pipes are in good condition. If an injury is caused by the escaping hydraulic fluid, see doctor at once! 13. Use a piece of cardboard or wood to detect leaks of hydraulic oil under pressure. 14. Be sure to relieve all hydraulic pressure before disconnecting any lines or pipes between the implement and the tractor hydraulic system. Keep all guards and shields in place. John Deere 455 Marker Installation Instructions See the Parts Section of this manual to identify individual components not mentioned in these installation instructions. 1. Place drill in a lowered field position. From each end of the drill box allow 16 ft. clearance for marker assembly. Refer to Figure 1 2. Mount the adapter plate (1) to the John Deere 455 Drill using u-bolt (2), USS flat washers (4), hardened flat washers (3), and lock flange nut (5). Also use 2-1/2 x 1 1/2 bolts (6) and 1-1/2 x 1 1/4 carriage bolt (7) with flat washers (8), and locking flange nuts (9). The carriage bolt (7) is inserted into the holes with the slots head first. It is then slid sideways into the square slot to be tightened 3. Attach the marker first section with mount (10) to the adapter plate on the drill frame as illustrated. Mount the 5/8 x 2" long bolts (11), and flanged hex nuts (12). Figure 1 Adapter Plate M 10/17/2002
9 Operating and Assembly Instructions 7 Refer to Figure 2 4. Assemble the marker in a horizontal position, remove the port plugs in the hydraulic cylinder to allow the fold cylinder to be extended. Then fold the first section and the lift lug channel (7) to a horizontal position. 5. With the shear bar positioned towards the front (2), align the holes of the second section with the holes of the lift lug channel (7) and bolt together with the 5/8 x 5 1/2 long bolt (3), lock nut (4), 3/8 x 2" long shear bolt (5), and lock nut (6). Figure 2 Lift Lug Channel and Shear Bar Refer to Figure 3 6. Place the third section (1) over the end of the second section (2) and insert hinge pin (3) through the second and third section pivot. Secure the hinge pin (3) with 5/16 x 2" long bolt (4) and lock nut (5). Figure 3 Second and Third Sections /17/ M
10 8 John Deere & 30 Refer to Figure 4 7. Bolt the chain bar weldment (1) to the first section (2) with 3/8 x 3 1/4 long bolt (3) and lock nut (4). The chain bar weldment (1) should pivot freely on the 3/8 bolt (3). Bolt the chain bar (5) to the third section (6) with the 3/8 x 1 1/2 long bolt (7) and lock nut (4). The chain bar (5) should pivot freely on the 3/8 bolt (7). Connect the marker chain (10) between the chain bar (5) and chain bar weldment (1) with 5/16 utility clevis (9). With the marker disk adjusted for seeding width and disk touching the ground, adjust chain length to remove the slack. Adjustment should be made at the utility clevis (9) nearest to the drill. 8. The purpose of the 3/8 x 2 1/2 long stop bolt (11) is to hold tension on the marker chain (10) ONLY when the marker is in folded position. Therefore; the 3/8 stop bolt (11) and lock nuts (4) should be positioned in the first section (1) so the head of the stop bolt extends as little as possible. After marker is folded, adjust stop bolt to tighten chain. Refer to Figure 5 9. When mounting the marker carrier arm (1), on the 455, first mount the transport mount arm (2) to the drill frame using 3/8 x 6" x 7" long u- bolt (3), flat washers (4), and flanged nuts (5). The transport mount arm should be 45" - 55" away from the box end as shown. Next attach the marker carrier arm (1) to the transport mounting arm (2) using the 1/2 x 2" x 3" long u-bolts (6),flat washers (9) and flanged nuts (7). The marker carrier arm should be set at 31 3/8-31 7/8 above the drill frame as shown. 10. Mount the support arm saddle (8) to the marker carrier arm (1) with 1/2 x 2" x 3" long u-bolts (6), flat washer (9), and flanged nuts (7). The support saddle should be centered under the marker chain and the square tube of the second section, when folded to prevent wear. The support arm should support the second section parallel with the seed box lid. Adjustment can be made by loosening the u- bolts that clamp the marker carrier and slide marker carrier (1) up or down to parallel the marker with the drill box lid. Figure 4 Chain Bar Weldment Figure 5 Marker Carrier Arm and Transport Carrier Arm M 10/17/2002
11 Operating and Assembly Instructions 9 Refer to Figure Fold the marker to transport position. With the marker chain (10) in the slot of the support arm saddle, take up the slack in the marker chain by threading 3/8 x 2 1/2 long stop bolt (11) out against the chain bar weldment (1), lock this stop bolt in position with the two lock nuts (4). Figure 6 Marker Chain Refer to Figure The marker blade comes factory assembled as shown. The width of the mark that the blade makes can be adjusted by changing the angle of the blade. This is done by loosening the two 1/2 bolts in the blade adjuster, pivoting the blade to the preferred angle and tightening the bolts. Figure 7 Marker Blade (factory assembled) Refer to Figure If desired, the angle of the blade can be reversed by turning the blade adjuster upside down and reversing the blade so the depth band is on the inside as shown. Figure 8 Marker Blade (reversed) /17/ M
12 10 John Deere & 30 Refer to Figure Bolt the sequence valve (1) to the valve mount using the 3/8 x 3/4 long bolts (2). Remove the upper flanged nut holding the tongue to the crossbar on the cph frame (opposite the slow moving vehicle emblem). Insert the valve mount (3) on the existing bolt and replace the flanged nut. Attach the hydraulic hoses as shown. The front hoses going to the tractor should be routed through the tongue from the bottom side. Figure 9 Hydraulics M 10/17/2002
13 Hydraulic System 11 Hydraulic System Adjusting The Hydraulics 1. Be sure tractor hydraulic reservoir is full. 2. With the markers in field position, crack the hydraulics hose fittings located at the base end of one of the cylinders. With the tractor at an idle speed, activate the tractor hydraulics valve until hydraulic oil seeps out around the hose end. Tighten the hose end fittings. Repeat this process for the hose at the rod end of the cylinder. Crack the fittings on the back side of the sequence valve until hydraulic oil seeps out. Tighten and repeat for the opposite cylinder. 3. Cycle each cylinder 3 or 4 times slowly. Both arms should move to the vertical position on the first move and then they should lower and raise alternately as the hydraulic lever is operated. 4. Fold and unfold the marker(s) slowly in order to work all the air out of your marker hydraulics. Use caution when folding and unfolding the marker for the first time, and check for pinching and kinking of hoses.! CAUTION Escaping Fluid under pressure can have sufficient force to penetrate the skin. Check all hydraulic lines and hoses before applying pressure. Fluid escaping from a very small hole can be almost invisible. Use paper or cardboard, not body parts, to check for suspected leaks. If injured, seek medical assistance from a doctor that is familiar with this type of injury. Foreign fluids in the tissue must be surgically removed within a few hours or gangrene will result. NOTE: JIC fittings do not require high torque. JIC and O-Ring fittings do not require sealant. Always use liquid pipe sealant when adding or replacing pipe thread fittings. To avoid possible danger of cracking hydraulic fittings from over tightening, DO NOT use plastic sealant tape.! CAUTION Never allow anyone near the drill when cycling the markers. 5. The marker hydraulic system is equipped with needle valves to control how fast each marker operates. The needle valves are built into the sequence valve body. There are two hex adjustment heads, one for raising the markers, and one for lowering the markers. These are stamped in the valve body. To adjust the speed of each marker, screw the needle valve clockwise to adjust the raise or lower marker speed to a low setting. Fold the marker up and down a few times and recheck for pinching and kinking of hoses. With the tractor engine at an operating rpm, adjust the needle valve to limit the marker to a safe operating speed. Excessive folding speeds can cause marker damage.! CAUTION Excessive folding speeds can cause marker damage! 10/17/ M
14 12 John Deere & 30 Maintenance & Lubrication Maintenance Proper servicing and adjustment is the key to the long life of any farm implement. With careful and systematic inspection, you can avoid costly maintenance, time and repair. Breakaway Protection The marker arm is attached to the marker body with a 3/8" breakaway bolt. If excessive force is put on the marker during operation, the bolt will break, allowing the marker arm to swing away rather than cause damage to the marker. NOTE: The breakaway bolt is a 3/8"-16 x 2" long grade 2 (G.P. # C). It is identified as a grade 2 by having no marks on the head. If it breaks, it must be replaced by an equivalent grade 2 bolt to prevent marker damage. Marker Transporting Always transport the marker with it folded in the flat fold position M 10/17/2002
15 Maintenance & Lubrication Lubrication is required every 50 hours of operation. Lubrication Symbols As Required Use a multipurpose spray lub. Use as required. Do not over lubricate. 10 Lubrication is required every 10 hours of operation. Lubrication is required Seasonally Lubrication 25 1st Hinge Zerk Type of Lubrication: NLGI Grade 2 or 3 grease lubricant 25 2nd Hinge Zerk Type of Lubrication: NLGI Grade 2 or 3 grease lubricant 10/17/ M
16 14 John Deere & 30 Lubrication 25 3rd Hinge Zerk Type of Lubrication: NLGI Grade 2 or 3 grease lubricant Seasonally Disk Bearings Type of Lubrication: NLGI Grade 2 or 3 grease lubricant M 10/17/2002
17 Troubleshooting 15 Troubleshooting Problem Hydraulic marker functioning improperly Blade does not mark Solution Check all hose fittings and connections for air and oil leaks. The chain on the folding marker should be slack when the marker is both fully extended and fully raised. Check tractor hydraulic oil level. Check all bolts and fasteners. If needle valve is plugged; open valve, cycle markers, and reset the needle valve. Double selector valve positioned for fold cylinders. Shift valve to marker sequence position. The marker folding linkage and chain must have enough slack to allow the marker disk to drop down into depression in the field. Maximum down float should be limited by the slots at the rod end of the marker cylinder, and not by the chain. Read the adjustments section of this manual when adding slack to chain. The blade may be reversed to pull dirt in or throw dirt out depending on soil conditions. An optional smooth blade is available through your Great Plains dealer. The notch blade comes with your marker as standard equipment. 10/17/ M
18 16 John Deere & 30 Parts Flat Fold Marker Assembly M 10/17/2002
19 Parts 17 Ref. Part No. Description H L.H. MARKER MOUNT Shown H R.H. MARKER MOUNT H LH FIRST SECTION Shown H RH FIRST SECTION C BUSHING CYL 1 1/4 X 1 X C GREASE ZERK STRAIGHT 1/ D FIRST PIVOT SHAFT C HHCS 3/8-16X3 1/4 GR C NUT LOCK 3/8-16 PLT H LIFT LUG CHANNEL LH Shown H LIFT LUG CHANNEL RH D SECOND PIVOT SHAFT C WASHER FLAT 1 SAE D PIN 1 OD X 4.34 USABLE C PIN COTTER 3/16 X C HHCS 1/2-13X4 3/4 GR C NUT LOCK 1/2-13 PLT C HHCS 3/8-16X2 GR D CYLINDER STOP D STOP BUSHING H 3 SECTION MARKER BREAKAWAY Shown H 2ND SECTION C WASHER FLAT 3/8 USS PLT C HHCS 3/8-16X1 1/2 GR D HINGE PIN H 30 F.F. MKR. 3RD. SECTION C NUT HEX JAM 1/2-13 PLT C SCREW SET SQ HD 1/2-13X1 1/2G C WASHER FLAT 1/2 USS PLT D MARKER TUBE 42 LG S MARKER DISC & HUB ASSEMBLY C HHCS 1/2-13X3 GR C CYL 2.5X20X1.12 ROD (TIE)1 PIN H CHAIN BAR WELDMENT C HHCS 3/8-16X2 1/2 GR5 FTHD C NUT HEX NYLOCK 5/8-11 PLT C HHCS 5/8-11X5 1/2 GR D 24 MARKER CHAIN Shown D MARKER CHAIN C 5/16 x 1 1/4 UTILITY CLEVIS D CHAIN BAR C WASHER FLAT 1/2 USS PLT C NUT HEX FLG. LOCK 1/2-13 PLT C HHCS 5/16-18X2 GR C NUT LOCK 5/16-18 PLT 10/17/ M
20 18 John Deere & 30 Flat Fold Marker Assembly (Cont.) M 10/17/2002
21 Parts 19 Ref. Part No. Description C NUT HEX FLANGE LOCK 3/4-10 PLT C HHCS 3/4-10X2 1/2 GR H L.H. MARKER MOUNT Shown H R.H. MARKER MOUNT C WASHER FLAT 3/8 USS PLT C NUT HEX LOCK 7/16-14 PLT H MARKER CARRIER H MARKER TRANS ARM MOUNT WDMT C U-BOLT 3/8-16 X 6 1/32 X C WASHER FLAT 1/2 USS PLT C NUT HEX FLG. LOCK 1/2-13 PLT C U-BOLT 1/2-13 X 2 X 3 GR H SUPPORT ARM SADDLE H JD455 MARKER ADAPTER LH Shown H JD455 MARKER ADAPTER RH C WASHER FLAT 3/4 USS PLT C WASHER FLAT 3/4 HARD ASTMF C NUT HEX FLANGE LOCK 3/4-10 PLT C HHCS 1/2-13X1 1/2 GR C WASHER FLAT 1/2 USS PLT C NUT HEX FLG. LOCK 1/2-13 PLT C RHSNB 1/2-13X1 1/4 GR C U-BOLT 3/4-10 X 6 1/32 X 11 10/17/ M
22 20 John Deere & 30 Disk Assembly M 10/17/2002
23 Parts 21 Ref. Part No. Description S MARKER DISC & HUB ASSEMBLY H 1 SPINDLE MARKER WELDMENT C TINE GAUGE WHEEL HUB SEAL C BEARING CONE L C BEARING CUP L RELIABLE HUB 4 BOLT C GREASE CAP # C TINE GW HUB C WASHER FLAT 3/4 SAE PLT C NUT HEX SLOTTED 3/ C PIN COTTER 5/32 X 1 1/4 LG C 16 4-BOLT NOTCHED MARKER DISK H DEPTH BAND 10 4-BOLT 4B.C. 14. BO-47 NEILSON STUD 1/2-20UNFX1 13/ C NUT LUG 1/2-20 X 60 DEG PLT 10/17/ M
24 22 John Deere & 30 Hydraulic Assembly M 10/17/2002
25 Parts 23 Ref. Part No. Description C EL 9/16MJIC 9/16MORB C EL 9/16MJIC 9/16FJIC C HH1/4R /16FJIC C HH1/4R /16FJIC C HH1/4R /2MNPT 9/16FJIC C WASHER LOCK SPRING 3/8 PLT C HHCS 3/8-16X3/4 GR C VALVE,SEQUENCE SHOEMAKER D VALVE MOUNT C CYL 2.5X20X1.12 ROD (TIE)1 PIN C PLASTIC HOSE LABEL C CABLE TIE 2 DIA MIN - ORG 10/17/ M
26 24 John Deere & 30 Hydraulic Cylinder ( C) M 10/17/2002
27 Parts 25 Ref. Part No. Description 1. 1M6006 CLEVIS 2. 2M3326 ROD 3. 3R0310 MW HEAD 4. 4M3108 MW PISTON 5. 5M3128 TUBE 6. 6R0158 BASE MIDWAY 7. 7M3328 TIE ROD 8. 2A0208 CLEVIS PIN 9. * WIPER SEAL 10. * O-RING 11. * BACK UP (ROD) 12. * O-RING 13. * BACK UP (PISTON) 14. 2A0022 PISTON NUT 15. 2A0012 CLEVIS NUT 16. 2A0012 TIE ROD NUT C HHCS 3/8-16X1 3/4 GR A0132 PIN CLIP C SEAL KIT MW 2.5 CYL 3A3102 * AVAILABLE IN SEAL KIT. 10/17/ M
28 26 John Deere & 30 Sequence Valve ( C) M 10/17/2002
29 Parts 27 Ref. Part No. Description BODY, SEQUENCE VALVE O-RING PLUG, HEX SOCKET NEEDLE, FLOW CONTROL PIN,.125" SPRING PIN SPRING, COMPRESSION 7. * O-RING Seal kit only 8. * RING, TEFLON BACK-UP Seal kit only SCREW, FLOW CONTROL ADJUSTMENT HEX, JAM NUT ZINK PLATED 11. * SPRING, DETENT Seal kit only 12. * CHROMIUM STEEL BALLS Seal kit only 13. * CHROMIUM STEEL BALL Seal kit only 14. * SPRING Seal kit only O-RING FITTING, PORT ADAPTOR HEX, SOCKET O-RING PLUG O-RING CONNECTOR, STRAIGHT SPOOL, MARKER SEQUENCE.055" ORIFICE C SEAL KIT SHOEMAKER #1223 Not shown 10/17/ M
30 28 John Deere & 30 Appendix Torque Values Chart Bolt Head Identification Bolt Head Identification Bolt Size (Inches) Grade 2 Grade 5 Grade 8 in-tpi 1 N m 2 ft-lb 3 N m ft-lb N m ft-lb mm x pitch 4 N m ft-lb N m ft-lb N m ft-lb 1/4" M 5 X /4" M 6 X / M 8 X /16" M 8 X /8" M10 X /8" M10 X /16" M12 X /16" M12 X /2" M12 X /2" M14 X /16" M14 X /16" M16 X /8" M16 X /8" M18 X /4" M18 X /4" M20 X /8" M20 X /8" M24 X " M24 X " M30 X /8" M30 X /8" M36 X /4" M36 X /4" Bolt Size (Metric) Class 5.8 Class 8.8 Class /8" in-tpi = nominal thread diameter in inches-threads per inch 1 3/8" N m = newton-meters 1 1/2" ft-lb= foot pounds 1 1/2" mm x pitch = nominal thread diameter in millimeters x thread pitch Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above M 10/17/2002
31 Appendix 29 Warranty Great Plains Manufacturing, Incorporated warrants to the original purchaser that this seeding equipment will be free from defects in material and workmanship for a period of one year from the date of original purchase when used as intended and under normal service and conditions for personal use; 90 days for commercial or rental purposes. This Warranty is limited to the replacement of any defective part by Great Plains Manufacturing, Incorporated and the installation by the dealer of any such replacement part. Great Plains reserves the right to inspect any equipment or part which are claimed to have been defective in material or workmanship. This Warranty does not apply to any part or product which in Great Plains judgement shall have been misused or damaged by accident or lack of normal maintenance or care, or which has been repaired or altered in a way which adversely affects its performance or reliability, or which has been used for a purpose for which the product is not designed. This Warranty shall not apply if the product is towed at a speed in excess of 20 miles per hour. Claims under this Warranty must be made to the dealer which originally sold the product and all warranty adjustments must by made through such dealer. Great Plains reserves the right to make changes in materials or design of the product at any time without notice. This Warranty shall not be interpreted to render Great Plains liable for damages of any kind, direct, consequential, or contingent, to property. Furthermore, Great Plains shall not be liable for damages resulting from any cause beyond its reasonable control. This Warranty does not extend to loss of crops, losses caused by harvest delays or any expense or loss for labor, supplies, rental machinery or for any other reason. No other warranty of any kind whatsoever, express or implied, is made with respect to this sale; and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale. This Warranty is not valid unless registered with Great Plains Manufacturing, Incorporated within 10 days from the date of original purchase. 10/17/ M
32 Great Plains Manufacturing, Inc. Corporate Office: P.O. Box 5060 Salina, Kansas USA
Planting Components. Operator s/parts Manual. Row Cleaner VIII. Terra-Tine
Operator s/parts Manual Terra-Tine Row Cleaner VIII Planting Components! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without
More informationPlanting Components. Operator s/parts Manual. John Deere 30 Dual 750 Flat Fold Marker
Operator s/parts Manual John Deere 30 Dual 750 Flat Fold Marker Planting Components! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious
More informationPlanting Components. Operator s/parts Manual
Operator s/parts Manual Unit Mount Conservation Coulter and Spring Package Attachment for JD 7000, JD 7200, White 6100, Kinze Planters and Great Plains Row Units Planting Components! Read the operator
More informationPlanting Components. Operator s/parts Manual. John Deere & 20" Flat Fold Marker
Operator s/parts Manual John Deere 750 15 & 20" Flat Fold Marker Planting Components! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious
More informationPlanting Components. Operator s/parts Manual Terra-Tine. Row Cleaner
Operator s/parts Manual Terra-Tine Row Cleaner Planting Components! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without
More informationOperator s/parts Manual
Operator s/parts Manual Precision Fertilizer Hitch Flat Fold Marker Manufacturing, Inc.! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious
More informationPlanting Components. Operator s/parts Manual Heavy Duty Fertilizer Coulter
Operator s/parts Manual Heavy Duty Fertilizer Coulter Planting Components Read the operator manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without
More informationOperator s/parts Manual
1--1 4/8/04 Operator s/parts Manual 30 3-Section Flat Fold Marker Manufacturing, Inc. P.O. Box 5060 Salina, Kansas 67402-5060! Read the Operator s manual entirely. When you see this symbol, the subsequent
More informationPlanting Components. Operator s/parts Manual Vantage II
Operator s/parts Manual Vantage II Planting Components! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your
More informationOperator s/parts Manual
Operator s/parts Manual 3-Point Solid Stand Drills Pull Hitch Package Manufacturing, Inc. P.O. Box 5060 Salina, Kansas 67402-5060! Read the operator s manual entirely. When you see this symbol, the subsequent
More informationAssembly Instructions. General Information
Great Plains Mfg., Inc. Installation Instructions! Used with: 1200, 1210 and 1220 1500, 1510 and 1520 2000, 2010 and 2020 12, 15 and 20 Series Drills Folding Markers When you see this symbol, the subsequent
More information! CAUTION! ! WARNING!
Assembly Instructions! 24- and 30-Foot, No-Till Flat Fold Marker Option Used with: 2N-2410 and 2N-3010 Drills 2N-2420 and 2N-3020 Drills When you see this symbol, the subsequent instructions and warnings
More informationGeneral Information. Assembly Instructions. Dual Marker Option
Installation Instructions 12 Center Pivot Hitch Used with: 12 Center Pivot Hitch General Information! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More information! CAUTION! ! WARNING!
Assembly Instructions! 3N-3010P, No-Till Flat Fold Marker Option Used with: 3N-3010P Drills When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your
More informationGeneral Information. Assembly Instructions. Before You Start. Marker Assembly. Assembly Instructions S and S Marker Option
Great Plains Mfg., Inc. Assembly Instructions! Used with: 3000-3S 30 3-Section Folding Drill 2600-2S 26 2-Section Folding Drill Before You Start 3000-3S and 2600-2S Marker Option When you see this symbol,
More informationUpdate Manual. Manufacturing, Inc. 7 & 10 End Wheel No-Till Clutch Linkage. P.O. Box 218 Assaria, Kansas Effective 5/3/ M
Update Manual 7 & 10 End Wheel No-Till Clutch Linkage Manufacturing, Inc. P.O. Box 218 Assaria, Kansas 67416 Effective 5/3/96 152-156M General Information General Information Important Notice Great Plains
More informationInstallation Manual. Manufacturing, Inc. Yield-Pro Unit-Mount Coulter
Table of Contents Appendix Installation Manual Yield-Pro Unit-Mount Coulter Manufacturing, Inc. www.greatplainsmfg.com Read the operator manual entirely. When you see this symbol, the subsequent instructions
More informationPredelivery Instructions
PINK Predelivery Instructions SR5030 Split-Row Planter Manufacturing, Inc. P.O. Box 5060 Salina, Kansas 67402-5060! Read this manual entirely. When you see this symbol, the subsequent instructions and
More informationParts Manual FH6424HD, FH6630HD, FH6636HD, FH6642HD FH6845HD, FH6848HD & FH6851HD Series Harrow. Copyright 2016 Printed 04/03/ P
Table of Contents Part Number Index Parts Manual 6000 Series Harrow FH6424HD, FH6630HD, FH6636HD, FH6642HD FH6845HD, FH6848HD & FH6851HD Read the Operator's manual entirely. When you see this symbol, the
More informationParts Manual HB40/25. Hipper Bedder. Copyright 2017 Printed 06/28/ P
Table of Contents Parts Manual Hipper Bedder HB40/25 Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your
More informationOperator s Manual. Manufacturing, Inc. Inline Ripper Hitch
Operator s Manual Inline Ripper Hitch Manufacturing, Inc. www.greatplainsmfg.com! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationSpike Tooth Harrow STH P Parts Manual. Copyright 2017 Printed 06/30/17
Spike Tooth Harrow STH2024 30897 322-315P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your
More informationLandscape Pull Type Rakes
Landscape Pull Type Rakes LRP05 & LRP15 Series LRP05 Series 20997 LRP15 Series 20997 302-223M Operator s Manual! Read the Operator s manual entirely. When you see this symbol, the subsequent instructions
More informationAssembly and Parts Manual
Assembly and Parts Manual Detracker Manufacturing, Inc. www.greatplainsmfg.com Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationGeneral Information. Veris Drive Option
Installation Instructions 3-Point Precision Seeding System Used with: 1510P and 1520P 2010P and 2020P 2410P and 2420P! When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationGeneral Information B L R F
Great Plains Mfg., Inc. Appendix Installation Instructions 1 Flat Fold Marker Single Section YP Planters Used with: YP425A, YP425A3P YP625A, YP625A3P, YP625PD/TD YP825A, YP825A3P YP925TD When you see this
More informationTrip Edge Blade TB2596 & TB P Parts Manual. Copyright 2017 Printed 12/29/17
Trip Edge Blade TB2596 & TB25108 26891 301-291P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationW & A 12 ROW TOP LEVELING STACKER LEVEL BANDER
W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER NO. 3640 OPERATOR S MANUAL TO THE OWNER: Congratulations on your purchase of a new W & A Top Leveling Stacker Level Bander. Your selection is an indication
More informationInstallation Instructions for Toolbar Pivot Extension for the YP1625, YP1625A, YP1625IR, YP1630F series planter
Installation Instructions for Toolbar Pivot Extension for the YP1625, YP1625A, YP1625IR, YP1630F series planter Before Getting Started Before you begin installation of your Toolbar Pivot Extension, read
More informationRA108CR, RA110CR, RA210CR & RA212CR
Cart Rake RA108CR, RA110CR, RA210CR & RA212CR 38863 512-069PK Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without
More informationRear Blade RBT3572, RBT3584 & RBT P Parts Manual. Copyright 2018 Printed 07/09/18
Rear Blade RBT3572, RBT3584 & RBT3596 24747 301-251P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationPredelivery Manual. Manufacturing, Inc. Yield-Pro Planter YP1225 & YP1625
Predelivery Manual 2005+ YP1225 & YP1625 Yield-Pro Planter Manufacturing, Inc. www.greatplainsmfg.com! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings
More informationLandscape Rakes LR3784 & LR P Parts Manual. Copyright 2016 Printed 02/03/16
Landscape Rakes LR3784 & LR3796 39423 302-337P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationW & A 12 ROW TOP LEVELING STACKER LEVEL BANDER
W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER NO. 3640 OPERATOR S MANUAL TO THE OWNER: Congratulations on your purchase of a new W & A Top Leveling Stacker Level Bander. Your selection is an indication
More informationAerator AR2596 & AR P Parts Manual. Copyright 2018 Printed 07/10/18
Aerator AR2596 & AR2510 27964 325-127P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your
More informationSnow Trip Blade STB1060 & STB P Parts Manual. Copyright 2018 Printed 11/01/18
Table of Contents Snow Trip Blade STB1060 & STB1072 39393 301-501P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationGRADING SCRAPERS INDUSTRIAL SERIES OPERATION, SERVICE & PARTS MANUAL FOR MODELS: GSI7-SS, GSI7, GSI8, GSI10, & GSI12.
GRADING SCRAPERS INDUSTRIAL SERIES OPERATION, SERVICE & PARTS MANUAL FOR MODELS: GSI7-SS, GSI7, GSI8, GSI10, & GSI12 September 2006 FORM: IndGradingScrpr.QXD TABLE OF CONTENTS Safety Information......................1-2
More informationBale Grabber BG2400 & BGE P Parts Manual. Copyright 2018 Printed 01/19/18
Bale Grabber BG2400 & BGE2400 70352 319-173P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationModel 35 PARTS MANUAL
Model 35 PARTS MANUAL Version 3-2007 Ashland Industries Inc. 1115 Rail Drive P.O. Box 717 Ashland, WI. 54806 Ph: 877-634-4622 Toll Free Ph: 715-682-4622 Fx: 715-682-9717 www.ashlandind.com Model 35 Scraper
More information4750 Drill. Repair Parts
4750 Drill Repair Parts #615997-2016 Identification Your CrustBuster drill is identified by a Serial Number and Model Number. Record these numbers in the spaces provided in this manual and refer to them
More informationPost Hole Digger SA30 & SA P Parts Manual. Copyright 2011 Printed 04/01/11
Table of Contents Post Hole Digger SA30 & SA35 19221 317-093P Parts Manual Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without
More informationSnow Pushers SPL0548 & SPL P Parts Manual. Copyright 2018 Printed 07/10/18
Snow Pushers SPL0548 & SPL0560 39713 303-454P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationAG PRODUCTS, LTD. YOU RE ALWAYS AHEAD... WITH A MODERN BEHIND.
SUMMER 2016 BADGER DISC HARROW Operator s Manual 011-1156 011-1166 001-1501 001-1501-1 011-1167 001-1501-2 001-1501-3 011-1176 001-1501-4 011-1177 MODERN AG PRODUCTS, LTD. YOU RE ALWAYS AHEAD... WITH A
More informationPredelivery Instructions
Predelivery Instructions TSF1080, TSF1090, TSF1280 and TSF1290 Front Fold Boom Sprayer Manufacturing, Inc. www.greatplainsmfg.com! Read the operator s manual entirely. When you see this symbol, the subsequent
More informationOperator s Manual. Go Galvanized! YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND.
SUMMER 2008 rock & landscape rake Operator s Manual 003-7445 003-7450 003-7460 003-7440 003-7445 003-7450 YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND. P.O. Box 790 Beaumont, Tx 77704 409.833.2665 1.800.231.8198
More informationClaw Grapple SGC P Parts Manual. Copyright 2018 Printed 01/23/18
Claw Grapple SGC0660 37460 380-164P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life
More informationGeneral Information. Assembly Instructions. Point-Row Option 2004-
3000-3S Used with: 3000-3S General Information! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!
More informationGrapples SGC P Parts Manual. Copyright 2017 Printed 11/27/17
Grapples SGC0548 35815 380-138P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and
More informationROTARY TILLER. Operation, Service & Parts Manual For "AS" Series. FORM: ASTillerBook.QXD
ROTARY TILLER Operation, Service & Parts Manual For "AS" Series FORM: ASTillerBook.QXD April 2002 TABLE OF CONTENTS Preparation......................................1 Assembly Instructions.............................2
More informationOperator s Manual. Go Galvanized! YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND.
SUMMER 2008 C2 tilting grader blade Operator s Manual YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND. 003-5336 003-5342 003-5531 003-5544 P.O. Box 790 Beaumont, Tx 77704 409.833.2665 1.800.231.8198 Fax: 409.726.8333
More informationJ. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH Ph: (419) Fax: (419)
OPERATORS MANUAL Rev.8.14.17 Talc Applicator (Hydraulic) J. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 www.jm-inc.com 2 Table
More information4745 Drill OWNER'S MANUAL (06-08) #
4745 Drill OWNER'S MANUAL (06-08) # 605865 Identification Your CrustBuster drill is identified by a Serial Number and Model Number. Record these numbers in the spaces provided in this manual and refer
More informationInstruction Manual. ATV Manual Plow Lift
Instruction Manual ATV Manual Plow Lift Manual Conventions This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol is used with a key word
More informationParts Manual. Verti-Till Ripper. 5, 7, & 9 Shank. Copyright 2010 Printed 09/13/ P
Table of Contents Parts Manual 5, 7, & 9 Shank Verti-Till Ripper Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationBB1248, BB1254, BB1260, BB1266 & BB1272
Table of Contents Box Scrapers BB1248, BB1254, BB1260, BB1266 & BB1272 30731 303-295P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings
More information3800 SERIES SINGLE HYDRAULIC LOCKING TOOLBAR
3800 SERIES SINGLE HYDRAULIC LOCKING TOOLBAR 2565-774_REV_D 02/2018 OPERATOR S MANUAL PART IDENTIFICATION YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222
More informationI-175 PARTS MANUAL Version 4-04
I-175 PARTS MANUAL Version 4-04 Ashland Industries Inc. 1115 Rail Drive P.O. Box 717 Ashland, WI. 54806 Ph: 877-634-4622 Toll Free Ph: 715-682-4622 Fx: 715-682-9717 www.ashlandind.com Model I-175 Scraper
More informationRotary Tillers SRT62 & SRT P Parts Manual. Copyright 2014 Printed 08/06/14
Rotary Tillers SRT62 & SRT76 37045 321-095P Parts Manual Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationOperator s Manual. Series VII 7551, 7553, 7556, 7558 & 7560 Field Cultivator, Rigid Hitch (Constant Level)
Operator s Manual Series VII 7551, 7553, 7556, 7558 & 7560 Field Cultivator, Rigid Hitch (Constant Level)! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and
More informationGrapples SGC1060 & SGC P Parts Manual. Copyright 2018 Printed 07/11/18
Table of Contents Part Number Index Grapples SGC1060 & SGC1072 35564 380-092P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious
More informationOperator s Manual. Go Galvanized! YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND.
fall 2010 3pt & quick attach Bale spears & 3pt bale carrier Operator s Manual YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND. 318-1006-i 318-1005-i 020-1500 020-1502 P.O. Box 790 Beaumont, Tx 77704 409.833.2665
More informationPowered Rakes PR2572 & PR M Operator s Manual. Table of Contents. Copyright 2006 Printed 6/06/06
Powered Rakes PR2572 & PR2596 10592 314-132M Operator s Manual! Read the Operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationHD HEAVY DUTY COULTER
2910-130-HD HEAVY DUTY COULTER OPERATOR S MANUAL PART IDENTIFICATION 2565-743_REV_A 11/2016 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website:
More informationRear Blades LR3684 & LR P Parts Manual. Copyright 2017 Printed 12/26/17
Rear Blades LR3684 & LR3696 35079 302-306P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your
More informationI-130 XL PARTS MANUAL Introduced 4/01/01
I-130 XL PARTS MANUAL Introduced 4/01/01 Ashland Industries Inc. Hwy. 13 South P.O. Box 717 Ashland, WI. 54806 877-634-4622 Toll Free - phone 715-682-4622 phone 715-682-9717 fax www.ashlandind.com MODEL
More informationI-110 PARTS MANUAL Updated 3/21/01
I-110 PARTS MANUAL Updated 3/21/01 Ashland Industries Inc. Hwy. 13 South P.O. Box 717 Ashland, WI. 54806 877-634-4622 Toll Free - phone 715-682-4622 phone 715-682-9717 fax www.ashlandind.com MODEL I-100,
More informationTalc Applicator OPERATORS MANUAL
OPERATORS MANUAL Rev.4.17.2017 Talc Applicator J. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 www.jm-inc.com 2 Table Of Contents
More informationLIMITED WARRANTY DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Published 08/15 LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material
More informationCAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Instruction Manual Notes: Page Manual Conventions This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol is used with a key word to alert
More informationJohn Deere Tractors MANUAL
John Deere 800-820 Tractors MANUAL 202 John Deere 800-820 Tractors Blade, pivot frame Cylinders & Hydraulics Main Frame, Brackets, Mounting Safety, Operation, Maintenance 9 Attachments Warranty 2 22 Industrial
More informationGeneral Information. Veris Drive Option
No-Till and No-Till Precision Seeding System Used with: 3N-3010P and 3N-3020P 3N-3010 and 3N-3020! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions & Safety Sign Locations Operating Instructions Assembly Instructions...
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions & Safety Sign Locations... 2 Operating Instructions... 3 Assembly Instructions... 5 500 & 600 Snowblower Drawings... 8 500 & 600 Snowblower
More informationDisc Harrows DH3510 & DH P Parts Manual. Copyright 2017 Printed 06/08/17
Disc Harrows DH3510 & DH3512 25984 322-251P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationCore Aerators CA2548, CA2560, CA P Parts Manual. Copyright 2018 Printed 07/10/18
Core Aerators CA2548, CA2560, CA2572 18984 325-020P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationHL4K PLATFORM LIFT INSTRUCTIONS
HL4K PLATFORM LIFT INSTRUCTIONS REIMANN & GEORGER CORPORATION MARINE PRODUCTS P/N 6114--- 6/19/15 BUFFALO, NY TABLE OF CONTENTS CHAPTER TITLE PAGE 1 SAFETY... 1 1.1 Introduction... 1 1.2 Safety Definitions...
More informationLandscape Rakes LR0548, LR0560, LR1560, LR1572, LR1584 & LR1596
Landscape Rakes LR0548, LR0560, LR1560, LR1572, LR1584 & LR1596 LR05 Landscape Rake Shown 10410! Read the Operator s Manual entirely. When you see this symbol, the subsequent instructions and warnings
More informationPOST HOLE DIGGER. Operation, Service & Parts Manual For Models D20 & D40. FORM: D20_40DigRev.QXD
POST HOLE DIGGER Operation, Service & Parts Manual For Models D20 & D40 FORM: D20_40DigRev.QXD September 2006 Revised August 2009 TABLE OF CONTENTS Introduction.............................1 Preparation..............................2
More informationRiding Mowers. Z44 and Z52 Accu-Z Razor (S/N and above) SM Service Manual Printed 9/24/09
Riding Mowers Z44 and Z52 Accu-Z Razor (S/N 472620 and above) 23802 357-044SM Service Manual 2006 Printed 9/24/09 Copyright 2006 All rights Reserved Land Pride provides this publication as is without warranty
More informationDitcher DT P Parts Manual. Copyright 2018 Printed 07/10/18
Ditcher DT35 33328 324-099P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the
More informationSGM1560, SGM1566, SGM1572 & SGM1578
Grapples SGM1560, SGM1566, SGM1572 & SGM1578 35183 380-051P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without
More informationTwin Screw Undercar Conveyor
Twin Screw Undercar Conveyor Owner s Manual #19015700 05-00 Table of Contents Operator Qualifications...................................... 1 Safety.................................................. 2-4
More information4200 & 6200 Owner s Manual & Parts Book
00 & 00 Owner s Manual & Parts Book Purchase Date Serial Number Model Number Tractor Model PN: - Dealer Date --0 Description Page To The Owner & Maintenance Safety Precautions & Torque Specifications Skid
More informationFORM: S-tine Cultivator.QXD
"S" TINE CULTIVATOR Operation, Service & Parts Manual For GST Series FORM: S-tine Cultivator.QXD February 2003 TABLE OF CONTENTS Introduction/Assembly.....................1 General Maintenance.....................1
More informationOperator s/parts Manual
Operator s/parts Manual CPH and CP1000 Coulter Command System Manufacturing, Inc. P.O. Box 5060 Salina, Kansas 67402-5060! Read the operator s manual entirely. When you see this symbol, the subsequent
More informationOutload Trough Roller Conveyor
Outload Trough Roller Conveyor OWNER'S MANUAL 00003400 (8/99) Table of Contents Warranty Information.............................. Inside Front Cover Operator Qualifications / Sign Off Sheet..............................
More informationSEED BED ROLLER SBR48, SBR60 & SBR P Parts Manual. Copyright 2018 Printed 07/10/18
SEED BED ROLLER SBR48, SBR60 & SBR72 25770 322-215P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More informationENGINE DRIVEN ROTARY MOWER
ENGINE DRIVEN ROTARY MOWER Operation, Service & Parts Manual For Models ERM-413, 416, & 617 April 2009 Form: ERMHydMower TABLE OF CONTENTS SECTION DESCRIPTION...PAGE 1 Introduction... 1 2 Preparation...2
More informationManufacturing, Inc. Manual. Series I 1700TT (S/N 2026NN-) Dual Valve Update Kit 1700TT Turbo-Till
Manual Series I 1700TT (S/N 2026NN-) Dual Valve Update Kit 1700TT Turbo-Till Manufacturing, Inc.! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings
More informationOperator s Manual. Manufacturing, Inc. Three-Point Soybean Machine M. Copyright 1997 Printed 4/18/ M+
Operator s Manual 2015 Three-Point Soybean Machine Model Serial No. 2015 1152M+ Manufacturing, Inc. www.greatplainsmfg.com! Read the operator s manual entirely. When you see this symbol, the subsequent
More informationWARRANTY REGISTRATION AND POLICY
WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material
More informationWalker Loader Bucket OPERATOR S AND PARTS MANUAL
Walker Loader Bucket OPERATOR S AND PARTS MANUAL Please Read and Save These Instructions For Safety, Read all Safety and Operation Instructions Prior To Operating Machine P/N 6690 TABLE OF CONTENTS Introduction
More informationTITAN UNIVERSAL UNIT MOUNTED FLOATING RESIDUE MANAGER
2967-030 TITAN UNIVERSAL UNIT MOUNTED FLOATING RESIDUE MANAGER YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail:
More informationBRAKE ASSIST SYSTEM INSERT SHEET
BRAKE ASSIST SYSTEM INSERT SHEET 246779 v1.1 DEGELMAN INDUSTRIES LTD. BOX 830-272 INDUSTRIAL DRIVE, REGINA, SK, CANADA, S4P 3B1 FAX 306.543.2140 PH 306.543.4447 1.800.667.3545 DEGELMAN.COM M28 & M34 MANURE
More informationSKID STEER COMBO PLOW
A DIV. OF NORTHERN STAR INDUSTRIES, INC. P.O. BOX 788 IRON MOUNTAIN, MICHIGAN 49801 SKID STEER COMBO PLOW INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS SAFETY PRECAUTIONS... 2 ASSEMBLY PROCEDURE... 3
More informationPre-Delivery Instructions
Table of Contents Appendix Pre-Delivery Instructions CTA4000 or CTA4000HD Air Drill Implement Manufacturing, Inc. www.greatplainsmfg.com Read the pre-delivery manual entirely. When you see this symbol,
More informationTalet Equipment International Ltd. Sand Kicker
Talet Equipment International Ltd. Sand Kicker Parts & Operators Manual P.O. Box 35 Strathmore AB Canada TP K3 www.taletattachments.com sales@taletattachments.com Toll Free -888-37-5878 Fax -403-934-304
More informationInstruction Manual. ATV Plow Tube System
Instruction Manual ATV Plow Tube System Manual Conventions This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol is used with a key word
More informationPost Driver Attachment
Attachment (Shown with Optional Power Cell Rotator) Models - 600, 850 Safety Instructions This safety alert symbol indicates important safety messages in this manual. When you see this symbol, carefully
More informationTwo-Stage Snow Blower For 4WD Pick Up Trucks. Operator s Manual
Two-Stage Snow Blower For 4WD Pick Up Trucks Operator s Manual Distrubuted by: Metal Fabricating LLC P.O. Box 831 Brodheadsville, PA 18322 Phone: 570-992-9989 SnowVac.com WARRANTY POLICY Metal Fabricating
More informationCRUSTBUSTER OWNER / OPERATOR MANUAL
CRUSTBUSTER OWNER / OPERATOR MANUAL MODEL # CB-1 CRUSTBUSTER Manufactured by: LEWIS BROTHERS MANUFACTURING, INC. Post Office Box 146 Baxley, GA 31513 Tel: (912) 367-4651 Fax: (912) 367-3958 5-2-17 1 INTRODUCTION
More information