YAMAHA RHINO 660 INSTALLATION INSTRUCTIONS
|
|
- Phebe Mason
- 6 years ago
- Views:
Transcription
1 YAMAHA RHINO 660 INSTALLATION INSTRUCTIONS PLEASE READ THE ENTIRE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. THIS KIT INCLUDES ALL NECESSARY PARTS WHICH INCLUDES A GIBSON PERFORMANCE MUFFLER AND A GARRETT T20 TURBO. THE FACTORY CARBURETOR AND AIR BOX ARE USED IN THE INSTALLATION AND THE FUEL PUMP IS REPLACED WITH AN ELECTRIC PUMP. THIS IS A DRAW THROUGH THE CARBURETOR SYSTEM SO THERE MAY BE SOME TURBO LAG TYPICAL WITH THIS TYPE OF INSTALLATION. NOTE: WITH ANY PERFORMANCE ENHANCING PRODUCTS THERE IS THE RISK OF DAMAGING THE ENGINE AND OR DRIVE TRAIN. THE RHINO HAS MANY AFTERMARKET PRODUCTS AVAILABLE TO HELP PREVENT SUCH DAMAGE. PARTS AVAILABLE ARE UPGRADED CLUCH SYSTEM, PISTONS, RODS AND ALSO A REV LIMITER MODIFCATION SO THE ENGINE CAN RUN AT HIGHER RPMS. WE RECOMMEND USING RACING GAS AND IF ANY PING IS HEARD IT WILL BE NECESSARY TO RUN RACING GAS. TO START OUT REMOVE THE SEATS, ENGINE COVER, DRIVER SIDE PLASTIC COVER UNDER THE SEAT AND DUMP BED. WHEN REMOVING THE DUMP BED IT IS NECESSARY TO DISCONNECT THE TAIL LIGHTS.
2 1. Remove the muffler and head pipes, to do this the head pipes must be loose in order to remove the muffler. YAMAHA RHINO 660 INSTALLATION head pipe 04 -UP RHINO Remover the air filter box, carburetor, and the rubber carburetor mount. be careful when disconnecting the throttle cable and choke cable as there are loose parts that need to be saved for reinstallation. It will be necessary to replace the main fuel jet and modify the needle, please see instructions from DYNOJET and make these modifications. we recommend the DJ 200 and to put one extra washer on the needle. 3. Disconnect the vacuum. line from intake manifold and cap off. If you use a boost gauge this is a good place to connect. muffler carburetor vacuum line vacuum line to boost gauge air filer box intake manifold
3 4. Remove factory fuel pump. 5. Mount the exhaust manifold with the 4 lock washers and nuts included. For a stronger installation you may want to change the manifold studs with grade 8 studs. Install the oil return fitting on to turbo and temporarily install the turbo in place. then locate the proper location for the oil scavenging pump under the turbo as shown. It would be best to use the oil return hose from turbo to locate position. for easy of drilling holes remove turbo, drill 4 holes and secure the pump with bolts included. factory fuel pump turbo ex. manifold ex. manifold turbo
4 6. Install turbo on to the exhaust manifold as shown. It may be easier to install right angle charge coupler to turbo before mounting. turbo ex. manifold right angle charge coupler 7. Locate the air intake pipe which goes between the carburetor and turbo compressor intake. Line up the pipe with the turbo inlet and plastic panel which is under the front driver side seat. See photos of this and location of carburetor and air filter box. Drill a 2 inch hole through the plastic so you can insert the air intake pipe. intake pipe drill a 2 inch hole turbo comp. intake
5 8. Install the intake pipe onto the turbo. Using the hanger included slip it over the intake pipe and mark the location where the hole needs to be drilled for the supporting intake pipe bracket. TIP: to limit the dirt/sand from entering the new carburetor area you can take a piece of fuel hose and slit it longwise and fit it into the hole cut for the intake pipe. then slide the intake pipe into place and you can now use silicone sealant to seal up the area. intake pipe 2 inch hole 8 turbo rubber carburetor adapter support bracket 9. Drill appropriate hole and secure the intake pipe with the support bracket and install the rubber carburetor adapter onto the end of intake pipe. Be sure to use the adapter which has the protuberance in the rubber to match the grove in carburetor. carburetor
6 10. Install the carburetor into the adaptor and throttle and choke cables to carburetor and reconnect. carburetor choke cable throttle cable 11. Temporality install the L brackets onto the air filter box as shown and connect the air box to the carburetor. Mark the seat frame in the proper place remove the air box and drill two holes for sheet metal screws. 12. Remove the L brackets from the air box and install them onto the seat frame. L bracket air filter box air filter box L bracket
7 13. Reinstall the air filter box onto the carburet and secure the air box to the L brackets. using the hose included reconnect the breather outlet to the air box. blow-by hose air filter box and intake hose 14. Install oil supply line by removing the fitting on the engine that goes to the oil cooler. Insert between the factory fitting and engine our adapter and secure with screws included. Screw in the right angle adapter fitting and attach stainless oil line to fitting. Bring line across engine to drivers side and thread line towards rear of rhino. Now bring the line over the top of the compressor and secure to oil inlet fitting on the turbo. See photo for proper location of line. oil line to turbo oil fitting adapter right angle oil fitting the line over the top of the compressor and secure to oil inlet fitting on the turbo
8 15. Install the oil return fitting included into the oil check/fill hole and secure. Using the oil return hose included thread hose around to oil return pump and fasten hose to right angle fitting of oil pump output. Secure with clamps included. oil return hose from oil pump oil check oil return fitting 16. Install the turbo oil outlet on the turbo and heat resistant oil return hose to turbo oil outlet and to inlet of oil pump as shown and secure with hose clamps. oil hose to oil return fitting 17. Mount the replacement fuel pump on the side of the passenger seat frame as shown. Drill holes in seat frame to match holes in L shaped mounting bracket. Secure with bolts included. Run fuel line from gas tank to inlet of fuel pump using the factory fuel filter. you may wish to use a higher flow aftermarket fuel filter. From the output side of fuel pump connect the included fuel line to carburetor. You may find that a fuel pressure regulator is needed if gas wants to run out of carburetor. Not included in kit. oil pump to carburetor oil hose from turbo oil outlet from fuel tank
9 18. The fuel and oil pump require more amps than are available in the engine compartment so we need to add a relay. Included in the kit is a 30 amp relay which needs to be connected to the battery. Open the front compartment and remove the battery cover. relay can be loose in the compartment. the wires connect as noted red and black with eyelet connect to battery. Spade connector goes to one terminal of the blue rectangular connector. There are different models of Rhino and some do not have the blue connector. Use a test light to determine which one is switched with ignition. Be careful which one you choose as one goes off when you put Rhino in gear and it will blow lots of smoke out the exhaust. A safe place to connect is on drivers side of Rhino is the light switch, the wire going into the switch turns on and off with the key. Connect there and then thread the long red wire under the hump in the floorboard back to the fuel pump. Find the proper length to connect to fuel pump and cut the wire connect that end to the fuel pump and to the additional wire which then connects to the oil pump. The black wire on both pumps then need to be grounded. charge pipe #2 charge pipe #1 30 A relay
10 19. Install the charge piping as shown using the black rubber coupler included on to rhino intake manifold. The engine cover will need to be notched to go over the charge piping The engine engine cover cover will need to be notched go over the charge piping 20.The last install is the muffler, remove the original hangers for the stock muffler. Install the outlet on turbo and using the silvery donut gasket. Slip it over the end of outlet and then attach muffler with bolts and springs as indicated. Do not tighten these bolts Be sure to leave plenty of flex between rear hanger the muffler and the exhaust outlet but tight enough so it will not leak. There is a lot of movement between engine and muffler. front The muffler is supported by 3 hangers hanger that will have to be installed. In the box with the muffler are some photos that show how the front mount is installed and the photo shone hear indicates rear hanger where it mounts. The muffler has 2 additional hangers. Remove the wire tie holder from the rear hanger frame where the hanger lines up and drill a hole through the bottom portion of the frame the same size the zip tie hole. Now secure the muffler hanger on drivers side with rubber flex mount. now connect the rubber flex mount on passenger side to muffler bracket and hanger. Line up the hole in hanger with frame and locate the place to drill for hanger bracket. Drill proper size hole and attach hanger. rear hanger front hanger
11 NOTE: BE SURE THERE IS ENOUGH CLEARENCE BETWEEN THE TAIL OF THE MUFFLER AND THE DUMP BED WHEN OPEN BY ADDING WASHERS TO CLEAR AFTER THE BED IS REINSTALLED. THE TURBO INSTALLATION SHOULD NOW BE COMPLETE, BEFORE REINSTALLING THE STOCK RHINO PARTS START THE ENGINE AND CHECK FOR OIL/ GAS LEAKS AND BE SURE ALL CONNECTIONS AND BOLTS ARE TIGHT.IF YOU PLAN ON RUNNING YOUR RHINO HARD YOU MAY WISH TO MAKE AN ADDITIONAL TURBO BRACE GOING FROM THE TURBO TO THE ENGINE, THERE IS AN EYELET ON THE TOP OF THE HEAD, A BRACE ALMOST STRAIGHT DOWN TO ONE OF THE OUTLET BOLTS SHOULD BE SUFFICIENT.. IF JUMPING THIS COULD HELP PREVENT THE TURBO FROM PULLING THE STUDS OUT OF THE HEAD. NOW REINSTALL THE BED,UNDER SEAT COVER, ENGINE COVER AND SEATS. INSTALLATION SHOULD NOW BE COMPLETE. IF YOU NEED ADDITIONAL HELP PLEASE CALL FOR TECHNICAL ASSISTANCE. ENJOY TURBO SPECIALTIES
12
4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationNote: Hydro-shields, filter charger kits and replacement parts are sold on-line at injenonline.com
Part number SES1202FMGT 2005 1/2-07 Subaru Impreza STi 2006-07 Subaru Impreza WRX 2.5L, 4 cyl. Turbo 1- Six piece mandrel bent piping 1- Giant size front mount (#11028) intercooler core and tanks 23 3/4
More informationCrawford Performance Top Mount Air/Oil Separator Install Instructions Version 1.12
Crawford Performance Top Mount Air/Oil Separator Install Instructions Version 1.12 Parts List Part Number Quantity Description Sent Received S0774 1 TMIC Air/Oil Separator F0365 1 Crank Case Breather Connector
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More informationPump Gas Instructions for Polaris And 800 Models. Important Information before Installing This System:
Pump Gas Instructions for Polaris 600 700 And 800 Models Important Information before Installing This System: Before you begin your turbo install, read through these instructions to determine if you are
More informationV1 Truck Manifold Turbo Kit for F-body
V1 Truck Manifold Turbo Kit for 98-02 F-body Prep: -Remove all A/C Components, Alternator and brackets, tensioner, front bumper, front bumper foam, and front bumper support. Remove radiator and cooling
More informationScion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #
TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # 11518000 Vehicle Type Chassis Code Engine Code Transmission Model Year Scion FR-S DBA-ZN6
More informationInstant Chat off the main page of Or simply call our tech team at
08+ Rotated Tuner Kit for Garrett GT Turbos 2016-11-03 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationTURBO KIT INSTRUCTIONS
Revision 12/20/10 TURBO KIT INSTRUCTIONS This turbo kit consists of the necessary parts to upgrade or add a turbo to your 22R/RE/RET. This kit may require some fabrication to address your particular application
More informationRotated Tuner Kit for Garrett GT Turbos
Rotated Tuner Kit for Garrett GT Turbos 031411 Thank you for purchasing the PERRIN performance rotated turbo kit. Installation of this turbo should only be performed by persons experienced in the installation
More informationC FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY
EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.
More informationIndustrial Injections Compound Turbo Installation For 6.7L Scorpion
Industrial Injections Compound Turbo Installation For 6.7L Scorpion Step 1: Whenever you are doing an installation the first thing you should do is unhook the batteries to avoid arcing. You will need an
More informationCrawford Performance Top Mount Air/Oil Separator Version 2 (S0714-1)
Crawford Performance Top Mount Air/Oil Separator 02-07 Version 2 (S0714-1) Parts List Part Number Quantity Description Sent Received S0707-1 1 TMIC Air/Oil Separator V2 F0365 1 Crank Case Breather Connector
More informationC40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
More informationRevised 10/22/2014 Page 2 of?
1.Remove side panels, hood, seat, fuel tank, and 2.Remove stock air box, remove fuel line muffler. Save exhaust springs and rubber muffler mounts for turbo bracket. Sand back surface flat for mounting.
More informationCHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
28 January 2014 1045140 6.7L Super B Special Turbo Installation (I-00266) 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid MazdaSpeed3/Mazdaspeed6 Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions will assist
More informationInstallation Instructions
Installation Instructions 2.0T FSI Intake Manifold: Featuring better flow, higher boost capacity, 40% larger plenum volume, and integrated flapper delete; this product will take your 2.0L VW TSI and FSI
More informationInstallation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM 1996-2002 4Runner 1997-1998 T100 1997-2004 Tacoma 2000-2003 Tundra * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg
More information7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only.
7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only. The purpose of this guide is to serve as a reference for use when
More information*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials 701 SuperJet Type 9
*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials 701 SuperJet Type 9 Item Qty Part Number Part Description 1 1 COMASM0964 701 SuperJet Type 9 chamber assy. (includes
More information*** FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials SeaDoo 951XP Twin
*** FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials SeaDoo 951XP Twin Item Qty Part Number Part Description 1 1 COMASM0851 951XP MAG Chamber assembly 2 1 COMASM0850
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More information***FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki Ultra 150 Triple Pipe
***FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki Ultra 150 Triple Pipe Item Qty Part Number Part Description 1 1 COMASM0947 Ultra 150 PTO Chamber assembly
More informationHonda Accord/Prelude
Honda Accord/Prelude 1984-1995 In Tank Fuel Pumps TEST 1. Turn the ignition OFF. 2. On the Accord, remove the screws securing the underdash fuse box to its mount. Remove the fuel cut off relay from the
More informationWorld Formula TECH MANUAL
World Formula TECH MANUAL Section 1 General Rules 1. Only stock Briggs & Stratton World Formula Model # 124435-8101 will be used in this class except as provided in this Tech manual. All parts will be
More informationCrawford Performance Top Mount Air/Oil Separator For 08 STi + Version 2 (S0713-1)
Crawford Performance Top Mount Air/Oil Separator For 08 STi + Version 2 (S0713-1) Parts List Part Number Quantity Description Sent Received S0709-1 1 TMIC Air/Oil Separator 08STI V2 F0365 1 Crank Case
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationPRXB EXHAUST BRAKE MAXIMUM EXHAUST FLOW DESIGN
MAXIMUM EXHAUST FLOW DESIGN PRXB EXHAUST BRAKE C44072/C44073/C44074/C44075/C44076 APPLICATION: 994-2002 DODGE RAM TRUCKS W/5.9L CUMMINS DIESEL ENGINES WITH MANUAL & AUTOMATIC TRANSMISSIONS STOCK DODGE
More informationCUMMINS 6.7L EXHAUST BRAKE PRXB EXHAUST BRAKE KIT FOR 2007½-2015 TRUCKS EQUIPPED WITH 6.7L CUMMINS ISB DIESEL ENGINES. C Kit C Kit
CUMMINS 6.7L EXHAUST BRAKE PRXB EXHAUST BRAKE KIT FOR 2007½-2015 TRUCKS EQUIPPED WITH 6.7L CUMMINS ISB DIESEL ENGINES C44038 4 Kit C44039 5 Kit BEFORE STARTING THE INSTALLATION please read the entire installation
More information*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Sea-Doo 785XP Spec I 1997
*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Sea-Doo 785XP Spec I 1997 Item# Qty Part # Part Description - 1 COMASM0200 785 Spec I hardware kit, 97 (includes items
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationInstallation Instructions Dual Perimeter Plate Nitrous System (#82185)
Installation Instructions Dual Perimeter Plate Nitrous System (#82185) Thank you for choosing ZEX. If at any time you have questions regarding this or any of our products, please call our ZEXTEK support
More informationRemove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0012 Fits: 2006-10 550i (4.8L) PARTS LIST Air Box Assembly Left tube Center tube Right tube Outer Tube AFM housing AFM/TB tube Hardware Kit Congratulations
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
26 September 2012 1045140 6.7L Super B Special Turbo Installation 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140 PLEASE
More informationPowerMax Diesel Upgrade For Cummins Engines
PowerMax Diesel Upgrade For Cummins Engines 00.5-007.5 Dodge Ram With Cummins 5.9L Item 3 4 5 6 7 8 9 0 3 4 5 6 7 8 Parts List Description Turbocharger Ancillary kit 773069- (includes) Installation Instructions
More informationAEROCHARGER TURBO SYSTEM INSTALLATION MANUAL. Can-Am Maverick Version 1.0
AEROCHARGER TURBO SYSTEM INSTALLATION MANUAL Can-Am Maverick 1000 Version 1.0 R INTRODUCTION Congratulations on your purchase of an Aerocharger Turbo system for the Can-Am Maverick 1000! You now own the
More information*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki STX-R Triple Pipe
*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki STX-R Triple Pipe Item Qty Part Number Part Description 1 1 COMASM0935 STX-R PTO Chamber assembly 2 1 COMASM0936
More informationPart number SP Mitsubishi Lancer 4 cyl. 2.0L non-turbo. 1- Three piece cold air intake
Part number SP1835 08-09 Mitsubishi Lancer 4 cyl. 2.0L non-turbo 1- Three piece cold air intake 1- Formed silicone hose (#3158) 1-2 1/2 Injen filter (#1012) 1-2 3/4 straight hose (#3043) 4- Power-Bands.312.040
More informationInstallation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
More informationBill of Materials for
Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationInstallation Instructions :BMW B58 : Page 1
Installation Instructions :BMW B58 : Page 1 1. We will start by removing the stock airbox system. Loosen the hose clamp around the airbox. Remove the MAF sensor plug the white clip unlocks by pulling it
More information2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
More informationZX-14 Stage I Turbo Kit
62910 Peerless Ct. Bend, OR 97701 Phone 541.385.0706 Fax 541.382.9406 ZX-14 Stage I Turbo Kit WARNING: This turbo kit is for OFF-ROAD RACING use ONLY. Advisement: These instructions are written to be comprehensive
More informationFactory Pipe Bill of Materials 650 Super Jet
Factory Pipe Bill of Materials 650 Super Jet Item# Qty. Part Description 1 1 Factory Pipe tunable cast aluminum headpipe 2 1 Factory Pipe aluminum chamber 3 1 Factory Pipe tuned exhaust manifold 4 2 100-120mm
More informationXRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS
XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS The use of NFU (No Further use) and REUSE (Re Use) relates to the individual parts storage when performing the upgrade. Also note that all
More information3 WRX/STI TURBO INLET HOSE
3 WRX/STI TURBO INLET HOSE Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance
More informationJBA Cat4ward Shorty Header Install (05-10 Mustang GT and Bullitt)
JBA Cat4ward Shorty Header Install (05-10 Mustang GT and 08-09 Bullitt) Installation Time: 6-8 Hours (Depending on Tools and Help) Tools Required: 8mm Socket 10 mm Socket 13mm Socket 15mm Deep Socket Ratchet
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationINSTRUCTIONS. #82044 Race Diesel Nitrous System
INSTRUCTIONS #82044 Race Diesel Nitrous System Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. Kit Parts List Description Qty. Description Qty. Nitrous Solenoid 2.088
More informationINSTALLATION INSTRUCTIONS PART NUMBER D
INSTALLATION INSTRUCTIONS PART NUMBER D440-0047 APPLICATION: 2017 BMW F22 230i/M240i & xdrive 2017 BMW F23 230i/M240i & xdrive Convertible 2016-17 BMW F30 330i/340i & xdrive 2017 BMW F31 330i xdrive Wagon
More informationFactory safe air/fuel ratio s for Optimum performance Patent# 7,359,795
Part Number SP1125 2007-09 BMW 335i 2008-09 BMW135i 3.0L Twin Turbo L6 This kit is equipped with the Injen/AMSOIL Ea nanofiber dry filters, Ea nanofiber filters do not require oil. 1-2 piece air intake
More information2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY
INSTALLATION GUIDE 2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning S-FLO Intake for the 2010+ Audi B8 S4 and B8 S5 3.0T. Exquisite build
More informationCARBURETION. Carburetor Identification. Models , , , , , , , , , , ,
Carburetor Identification Models 110400, 110600, 111400, 111600, 113400, 120400, 120600, 121400, 121600, 122600, 123400, 123600 Models 28S700, 311700 Service Carburetor Briggs & Stratton/Walbro LMS Models
More informationHW Prowler Carburetor Installation Instructions
HW Prowler Carburetor Installation Instructions Page 1 of 6 Carb Kit Contains: HW modified Mikuni 36mm pumper style carb Custom choke cable Fuel Line Clamp Instructions (2) Leaner and (2) richer main jets
More informationMfg. No: 49T G1
Parts Manual Mfg. No: 49T877-0004-G1 Copyright Briggs and Stratton. All Rights reserved 28-Feb-2018 Model Components Table Of Contents Page Blower Housing, Air Cleaner............................................................................
More informationFUEL SYSTEM/CARBURETOR/FUEL PUMP
13 FUEL SYSTEM/CARBURETOR/FUEL PUMP FUEL SYSTEM-------------------------------------------------------------------------------------13-1 SCHEMATIC DRAWING-------------------------------------------------------------------------13-2
More information7B1210 COBB BMW N54 Charge Pipe
7B1210 COBB BMW N54 Charge Pipe Installation Instructions Congratulations on your purchase of the COBB BMW N54 Charge Pipe for your BMW. The following instructions will assist you through your installation
More information03-04 Cobra. Hellion Power Systems Mustang Cobra Kit Instructions
Hellion Power Systems 03-04 Mustang Cobra Kit Instructions NECESSARY PARTS REQUIRED FOR INSTALLATION Necessary: 03-04 Cobra hellion Kit ONLY 99-01 Alternator #YR3210346AA Alternator Bracket #XR3Z-10153-AB
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More informationH F G I. A (1) Reducer. pg.2
301009 B A D C E H F G I J L M A (1) Reducer B (1) Coolant hose C (1)Block off bracket D (3) Clamps E (1) Cooler side block off plate F (1) Turbo manifold block off plate G (1) Intake manifold side blocker
More informationCorvette Stage X Twin Turbo Installation. Please read the entire instructions as we ve made many changes.
Corvette Stage X Twin Turbo Installation Please read the entire instructions as we ve made many changes. Disconnect battery. Remove plastic fuel rail covers over the valve cover. Remove Air Box in front
More informationIAG Competition Series Air / Oil Separator (AOS) For 2017 STI
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationIllustrated Parts List. Model Series 31A600. TYPE NUMBERS 0111 Through TABLE OF CONTENTS
Illustrated Parts List Model Series 31A600 TYPE NUMBERS 0111 Through 4139. TABLE OF CONTENTS FORM MS3735 REV S 11/21/2012 REPLACES FORM MS3735 REV R 05/08/2012 FILE IN SECT. 2 OF SERVICE MANUAL 31A600
More informationInstallation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware
More informationZZP LNF Cobalt Turbo Upgrade
ZZP LNF Cobalt Turbo Upgrade Note: These instructions are intended for installers with previous turbo installation experience. Some procedures will not be described in full detail. If you run into any
More informationIllustrated Parts List. Model Series 31A700. TYPE NUMBERS 0112 through TABLE OF CONTENTS
Illustrated Parts List Model Series 31A700 TYPE NUMBERS 0112 through 2454. TABLE OF CONTENTS FORM MS5533 REV R 11/30/2012 REPLACES FORM MS5533 REV P 05/08/2012 FILE IN SECT. 2 OF SERVICE MANUAL 31A700
More informationIllustrated Parts List. Model Series. AIR COOLED Horizontal Shaft
Illustrated Parts List Model Series 613400 AIR COOLED Horizontal Shaft FORM MS6154 REV C -- 12/14/2012 REPLACE FORM MS6154 REV B -- 06/10/2010 FILE IN SECT. 2 OF SERVICE MANUAL 613400 TYPE NUMBERS 0035,
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More informationReproduction. Not for. Illustrated Parts List 49T800. Model Series TYPE NUMBERS 0001 THROUGH 0021.
FORM MS10496 REV C 02/05/2016 REPLACES FORM MS10496 REV B 04/22/2014 FILE IN SECT. 2 OF SERVICE MANUAL Illustrated Parts List Model Series TYPE NUMBERS 0001 THROUGH 0021. PRINTED IN U.S.A. COPYRIGHT by
More informationIllustrated Parts List. Model Series AIR COOLED
FORM MS6154--06/10/2010 REPLACE FORM MS6154--03/06/2010 FILE IN SECT. 2 OF SERVICE MANUAL Illustrated Parts List Model Series AIR COOLED TYPE NUMBERS 0035, 0038, 0048, 0076, 0078, 0079, 0100, 0111, 0113,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationPolaris Axys Sidekick Installation Instructions
2016-2017 Polaris Axys Sidekick Installation Instructions 1. Remove hood and side panels. 2. Remove fasteners and slide console back. 3. Remove belt and driven clutch. 4. Remove clutch cover/ oil-tank
More informationFuel Pressure Regulator Kit PART# - RY12040-RRFPR-6S5
APPLICATION(S): Yamaha FX-SHO, FZR & FZS Fuel Pressure Regulator Kit PART# - RY12040-RRFPR-6S5 We strongly recommend the use of a service manual to familiarize yourself with the various components and
More information8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)
P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationIllustrated Parts List
FORM MS 56 08/11/2004 REPLACES FORM MS 56 11/14/2002 FILE IN SECT. 2 OF SERVICE MANUAL 312700 Illustrated Parts List Model Series 312700 TYPE NUMBERS 0101 through 01. TABLE OF CONTENTS Air Cleaner.........................
More informationWrenches: ⅞, 8mm, 10mm, 13mm, 19mm P. allen, Other: Electrical Tape
IAG Street Series Air / Oil Separator (AOS) For 2008-14 STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationPart number SP Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl.
Part number SP1898 2003-06 Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl. 1- Dyno-proven aluminum cast intake 1- Three piece intercooler pipes A (T/B), B (intercooler) C (turbo) 1-4 1/2 Injen filter (#1018) 1-1890
More information365-SUB Engine : Engine Assembly 365-SUB [1/1] Page 1 of 5
Page 1 of 5 1 951-11012 Bolt 2 951-11054 Valve Cover 2 951-11054 1 Valve Cover 3 731-07059 Breather Hose 4 726-04101 Hose Clamp 6 N/A 1 Intake Valve Spring Seat 7 751-11124 Pivot Locking Nut 7 751-11124
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST MUSTANG GT LONG TUBE HEADERS (M30000)
ADVANCED - Installation requires professional-type tools and advanced automotive-service skills. If you lack experience with internal engine modifications, an Advanced installation is probably beyond your
More informationProcedure: Installation of P/N: ATP-HGC-001 (Blow-off Valve Pipe kit) on the Hyundai Genesis Coupe 2.0T engine.
WWW.ATPTURBO.COM Page 1 of 6 Procedure: Installation of P/N: ATP-HGC-001 (Blow-off Valve Pipe kit) on the Hyundai Genesis Coupe 2.0T engine. Warning: Check local laws before adding turbo components to
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationHP10098 BASIC INDEPENDENT AIR SPRING ACTIVATION KIT
HP10098 BASIC INDEPENDENT AIR SPRING ACTIVATION KIT Thank you and congratulations on the purchase of a Pacbrake basic independent air spring activation kit. Please read the entire installation manual prior
More informationN55 Turbo upgrade install guide
N55 Turbo upgrade install guide Thank you for your purchase of the VTT BMW N55 Stage 2 turbo charger upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More information3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B
3 October 2016 PN#1045320 24V Dodge Twin Turbo Kit (I-00274) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Twin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045320 PLEASE READ
More informationEDWARD STREET WAGGA WAGGA NSW 2650 PHONE FAX AN AUSTRALIAN DISTRIBUTOR FOR SCHWITZER TURBOCHARGERS AND EQUIPMENT
- 1-364 EDWARD STREET WAGGA WAGGA NSW 2650 PHONE 02 6925 4348 FAX 02 6925 3314 AN AUSTRALIAN DISTRIBUTOR FOR SCHWITZER TURBOCHARGERS AND EQUIPMENT TOYOTA 100 SERIES FITTING INSTRUCTIONS. As at 2/2/09 1.
More informationGrimmSpeed Install Guide Series Installing the GrimmSpeed WRX Boost Control Solenoid Updated 4/14/15
GrimmSpeed Install Guide Series Installing the GrimmSpeed 2015+ WRX Boost Control Solenoid Updated 4/14/15 Introduction: This guide will illustrate the installation of the GrimmSpeed 2015+ WRX Boost Control
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationIllustrated Parts List
FORM MS 54 08/11/2004 REPLACES FORM MS 54 11/14/2002 FILE IN SECT. 2 OF SERVICE MANUAL 311700 Illustrated Parts List Model Series 311700 TYPE NUMBERS 0005 through 0209. TABLE OF CONTENTS Air Cleaner.........................
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
More information