OPERATION AND MAINTENANCE MANUAL. AseptiChair. Item ADC-01

Transcription

1 OPERATION AND MAINTENANCE MANUAL AseptiChair Item ADC-01 P.O. Box 1548 Woodinville, WA Fax: Internet:

2 TABLE OF CONTENTS Introduction Purpose Performance Characteristics Items Furnished Operation Instructions Chair Set-Up Chair Adjustments Collapsing the Chair Cleaning & Maintenance Parts List Parts Diagram TABLE OF ILLUSTRATIONS Figure 1 - Leg Adjustment Pin Location Figure 2 - Leg Adjustment Pin Placement Figure 3 - Folding Out Foot/Leg Rest Figure 4 - Arm Sling Pin Insertion Figure 5 - Backrest adjustment Figure 6 - Positioning footrest to vertical Figure 7 - Parts Diagram Page 2

3 PURPOSE: The ADC-01 Portable Dental Chair provides patient seating for field dentistry and medical treatment. The ADC-01 is fully adjustable from upright to supine positions. The ADC-01 is built with a high strength steel frame and rugged replaceable vinyl coverings, allowing for long-term use. PERFORMANCE CHARACTERISTICS: Dimensions Chair- Folded: 37 x 23 x 9.5 Extended: 72 x 28 x 46 Soft carrying case: 38 x 24 x 11 Weight Chair only: 30 lbs. In soft carrying case: 34.5 lbs. Maximum Load Capacity: Approx. 300 lbs. Range of Positions Minimum Seat Height: 11 Maximum Seat Height: 22 Backrest: Adjustable from upright (vertical) to supine (horizontal) positions Footrest: Adjustable from upright (vertical) to supine (horizontal) positions ITEMS FURNISHED ADC-01 Portable Dental Chair Soft padded carrying case with handles Operation and Maintenance Manual Page 3

4 CHAIR SET-UP: 1. Remove the chair from its carrying case and set it on the floor, legs down, in its folded position. Leg Adjustment Pins 2. Rotate the chair up onto one side and remove the leg adjustment pins from their storage pouch underneath the chair seat. (Fig. 1) Figure 1 - Leg Adjustment Pin Location Insert Leg Adjustment Pins Figure 2 - Leg Adjustment Pin Placement 3. Standing in front of the chair, put your toe on one of the front chair legs and lift up on the backrest and front seat portion. Raise chair seat to desired height. Lock in place by inserting leg adjustment pins through chair leg tube and into adjustment link on the right and left side of the chair. (Fig. 2) 4. When the chair has been raised and the height set, the foot and leg portion should be folded forward, out horizontally. It will stop in the horizontal position. (Fig. 3) Figure 3 - Folding Out Foot/Leg Rest Insert Pins Into Frame Holes 5. Insert right and left arm sling pins into holes on the sides of the seat frame. (Fig. 4) 6. Complete set-up by positioning backrest and placing headrest at the proper height on the front side of backrest. Figure 4 - Arm Sling Pin Insertion Page 4

5 CHAIR ADJUSTMENTS: 1. Seat Height- The ADC-01 chair seat height can be set at any of the five preset settings. Without a patient in the chair, put your toe on one of the front chair legs and lift up slightly on the chair seat. While lifting and holding seat, remove the leg adjustment pin from the right and left side. Align link with tube hole in any of the five positions and lock in place by inserting the pin and chain assembly. (see Fig. 1) Lift lever to position. Release to lock. 2. Backrest- The backrest may be set in any position from upright to full supine. To change the position of the backrest, simply lift the chrome friction lever on the back side of the backrest, lower backrest, then release lever to lock. WARNING NEVER LOWER THE BACK- REST WHEN A PATIENT IS IN THE CHAIR WITHOUT COM- PLETELY SUPPORTING THEIR WEIGHT FIRST. Figure 5 - Backrest adjustment To return the backrest to an upright position, lift backrest to desired position. Backrest will automatically lock in place. (Fig. 5) 3. Footrest- The footrest may be positioned in the normal horizontal operating position, or allowed to hang down vertically so a patient can be seated in a sitting position. To release footrest into the vertical position, first fold toe section inward, then lift slightly on footrest section. While lifting, pull the black knobs on each side of the chair frame to release and push footrest down into the vertical position. Lock in the vertical position by snapping holding strap around the chair leg frame. To reposition footrest in the horizontal position, unsnap holding strap from frame, lift footrest to the horizontal position until it locks, then unfold toe section out to horizontal. (Fig. 6) Figure 6 - Positioning footrest to vertical Pull Black Knob to Release Snap Around Frame 4. Headrest- The headrest slides freely on its mounting strap and can be positioned at different heights for different size patients. Page 5

6 COLLAPSING THE CHAIR: WARNING NEVER FORCE THE CHAIR INTO THE COLLAPSED POSITION. FORCING THE CHAIR DOWN WITHOUT RELEASING THE BACKREST ADJUSTMENT LEVER MAY BEND THE ADJUST- MENT ASSEMBLY AND WILL VOID THE WARRANTY. 1. Fold toe and then leg sections onto seat as it was originally stored. 2. Pull arm slings out of the holes in the chair frame. 3. Put your toe onto one of the front chair legs and lift up slightly on the seat, then remove height adjustment pins. While supporting chair weight, let the chair fold down toward the floor. 4. As the chair folds down, release the backrest adjustment lever until the chair collapses completely. Rotate the chair up onto one side and insert the leg adjustment pins into their storage pouch underneath the chair seat. 5. Fold the arm slings and headrest onto the chair and place folded chair into carrying case. CLEANING AND MAINTENANCE: Although bleach, when diluted to <10% and wiped clean immediately could be used, it is not recommended. The use of barrier covers and mild cleaning solutions is recommended as the primary asepsis approach on chair and stool upholstery instead of relying on chemicals. The use of barriers greatly extends the life of chair and stool upholstery and can be replaced between patients. WARNING NEVER SIT ON THE EDGE OF THE SIT- TING SURFACE. ALWAYS SIT IN THE CENTER OF THE SEAT. Page 6

7 NOTES Page 7

8 PARTS LIST Item Part Number Quantity 1 Seat Cover Assembly Armrest Right/Left Armrest Right/Left Cover, backrest Strap, headrest Screw, #8x5/8" Chrome SEMS Headrest, pillow assembly Armrest support rod assembly Tie Wrap, 30" Tie Wrap, 13" Strap, leg C/S, 1/4-20x1" BtnSoc S/S Hinge, back support Nut, 1/4-20 Nyloc S/S Back Support Assembly Leg adjustment link Hole plug, 1/4" black Endcap, 1" domed Leg Assembly, inside Leg Assembly, outside Bolt, 5/16-18 Grade 5 carriage Washer, 5/16 Flat S/S Nut, 5/16-18 Nyloc S/S Endcap, 1" insert C/S, 1/4-20x1-1/4" BtnSoc S/S Toe Frame Assembly Nut, 5/16-18 hex S/S Foam, seat pad Spring Pin, 1/4x3/4" S/S Leg Frame Assembly, cmpl Knob, 5/16-18 insert cornet Spring,.420Dx.038Wx.875L comp C/S, 5/16-18x1-1/4" S/S C/S, 5/16-18x1" S/S SMS, PanPhl #6 x 5/8 Tapping Washer, 5/16 SAE S/S Seat Frame Assembly, cmpl Pin, leg adjustment assembly C/S, 1/4-20x1-3/4" BtnSoc S/S Hole plug, 3/4" black Backrest Frame Assembly Spacer, 1/4ID x 3/4OD Coved Spacer, 1/4ID x 3/4OD x.250 thick Not Shown Case, carrying w/handles Not Shown Backrest Assembly, cmpl Page 8

9 PARTS DIAGRAM Aseptico ADC-01 Portable Dental Chair Figure 7 - Parts Diagram

10 NOTES

11 NOTES

12 WARRANTY Aseptico warrants its products against defects in material or workmanship for a period of two (2) years, from date of original invoice. Some handpieces are warranted for one year under the same conditions. Other handpieces and expendable components, such as air turbines and light bulbs, are covered by shorter warranty periods, or have no warranty. Aseptico's sole obligation under product warranty is (at its sole option and discretion) to repair or replace any defective component or product in part or whole. Aseptico shall be the sole arbiter of such action. In the event of alleged defect under warranty, the purchaser is to notify Aseptico's Customer Service Department promptly. Customer Service will provide instructions, usually directing that the product be returned for service. Shipment to Aseptico and the cost thereof is always the responsibility of the purchaser. Accidental misuse, inappropriate installation, or failure to perform directed maintenance voids the warranty. Deliberately defacing, modifying, or removing the serial number voids the warranty. Aseptico does not assume, under this warranty, any risks or liabilities arising from the clinical use of its products, whether or not such use involves coincidental utilization of products manufactured by others. P/N: Rev. H ECO /2016 P.O. Box 1548 Woodinville, WA Fax: info@aseptico.com Internet: PRINTED IN THE USA