Catalog Cuts. for. Lucian Adams Elementary School - Hurricane Harvey Recovery (PAISD) Sorted by Manufacturer

Transcription

1 Catalog Cuts for Lucian Adams Elementary School - Hurricane Harvey Recovery (PAISD) Sorted by Manufacturer Prepared By HUSHMI HAMEED ALLEGION, PLC N PENNSEYLVANIA CARMEL IN Created 2/16/2018 PDF created by SpeXtra Page 1

2 Catalog Cut Summary Mfr Description Catalog Number Cut Page Number BES RIM CYLINDER 1E-72 BES_0008 BES PRIVACY 93K-0L-15D BES_8002 GLY OH STOP 90S GLY_0003 IVE KICK PLATE K " X 2" LDW B-CS IVE_0223 IVE DOOR STOP 409 IVE_0141 IVE SILENCER 608 IVE_0148 IVE DUST PROOF STRIKE 570 IVE_0098 IVE MANUAL FLUSH BOLT 555 IVE_0097 IVE COAT AND HAT HOOK 802 IVE_0198 IVE PULL PLATE 106 X 70E IVE_0128 IVE PUSH PLATE 70E IVE_0127 IVE FLOOR STOP/HOLDER 491 IVE_0136 NOR CLOSER 1600BF (REG/PA AS NOR_0001 REQ'D) SCE DOOR CONTACT HM SCE_0060 VON POWER TRANSFER EPT10 VON_0201 ZER DOOR BOTTOM 369AA6 ZER_0132 ZER GASKETING 188SBK PSA ZER_0114 ZER THRESHOLD 164A-226 ZER_0104 ZER MULLION SEAL 8780NBK PSA ZER_0114 ZER ASTRAGAL 328AA ZER_0139 Project: Lucian Adams Elementary School - Hurricane Harvey Recovery (PAISD) Control #: Print Date: Feb :57PM EST Company: Allegion, PLC Version #: 1 Ver Date: Feb :31PM EST Page 2 of 2

3 1E SERIES TABLE OF CONTENTS Page Page 1E Series Features...2 Eurocylinders...7 1E Series Specs/How to Order...2 Cylinders and Cams...8 1E Series Rings/Spindles/Mortise Service Equipment...3 1E Cylinder Special Rings...9 1E Series Special Cylinders...4, 5 5E Series Specs/Accessories E7J4/1E7K4 High Security Cylinders...6 5E Series How to Order...11 Patented Keying...6 1E SERIES FEATURES 1E Mortise Cylinder Standard mortise applications require use of BEST s 1E Series cylinders with standard 1E-C4 cam. BEST cylinders may be altered to function with other manufacturers' locks by use of different cams (see page 8) and different cylinder rings (see page 9). Special cylinder variations are available for most applications (see pages 4 & 5). BEST cylinders are machined from brass or bronze bar stock and are available in a variety of finishes. Additional security is provided by a set screw that mounts diagonally in the cylinder wall and when tightened, holds the cylinder securely in the housing. BEST mortise cylinders feature the BEST interchangeable core and may be masterkeyed into any existing BEST system. Contact your local Best Access Systems sales office for information on special cylinder applications not listed in this catalog. 1E Rim Cylinder Standard rim cylinder applications require the use of BEST s 1E rim cylinder series. BEST rim cylinders are interchangeable with other manufacturers rim cylinders. BEST rim cylinders are machined from solid bar stock and are available in a variety of finishes. The standard package for the BEST rim cylinder includes cylinder, RP3 ring package, 1E-S2 spindle, clamp plate and clamp plate screws. BEST rim cylinders feature the BEST interchangeable core and may be masterkeyed into any existing Best system. ECIFICATIO Specifications Cylinder Dimension A Door Nomenclature A Thickness 1E " 1 5 8"to 2 1 4" 1E " 1 7 8"to 2 1 2" Cylinder diameter " To order: see below example: 1E74-C4-RP3-626 Products covered by on or more of the following patents: 4,437,695 4,633,690 4,616,394 A Specifications Cylinder Dimension Door Nomenclature A Thickness 1E " 1"to 2 3 4" 1E " 1 1 4"to 3" Cylinder diameter " To order: see below example: 1E72-S2-RP3-626 HOW TO ORDER HOW TO ORDER STEP A B C D E F G 1E 7 4 C4 RP3 626 ** Cylinder Core Function Standard Cam or Rings Standard Diameter Housing Code Length Mortise Code Spindle Finishes 1E " 0 dummy 2 rim Blank standard C4 standard cam RP1 tapered cyl E 1 1 2" 6 6 pin 4 mortise* " C181 Adams Rite RP2 6 pin mortise E see 7 7 pin 6 tapered "up to MS cam RP3 std. package pages 10,11 housing mortise 96 6" S2 standard RP4 3E mortise E see accepts spindle page 7 all Best cores see pages 4-5 for special cylinders (see page 4-5) (For special cams see page 8) (For special rings see page 9) Specify hand if required * For additional special mortise cylinders, see pages 4 and 5. ** Must specify keymark and number of keys or designate L/C for less core. 2 MORTISE AND

4 STANDARD RINGS RP Standard Ring Package The RP standard ring package includes a 1E-R3 ( 3 16" ) and 1E-R5 ( 3 8" ) ring. 1E-R3 3 16" 1E-R5 3 8" STANDARD CAM Standard Cam for 1E-64, and 1E-74 Mortise Cylinders Unless otherwise specified, the 1E-C4 cam is supplied on all 1E mortise cylinders. Standard Commonly used cams are listed on page 8. 1E-C4 Cam If a cam other than the variety listed is needed, a sample cam should be forwarded to your local BEST office along with the lock manufacturer s name and lock series or identification number. STANDARD CAM RP1 Ring Package The RP1 ring package for the 1E-76 cylinder includes a 1E-R2 ( 1 8" ) and 1E-R3 ( 3 16" ) ring. 1E-R2 1 8" RP2 Ring Package The RP2 ring package for the 1E-64 cylinder includes a 1E-R2 ( 1 8" ) and 1E-R4 ( 1 4" ) ring. 1E-R2 1 8" 1E-R3 3 16" 1E-R4 1 4" RP3 Ring Package The RP3 ring package for the 1E-62, 1E-72 and 1E-74 cylinders includes a 1E-R2 ( 1 8" ) and a 1E-R5 ( 3 8" ) 1E-R2 1 8" 1E-R5 3 8" 1E-S2 Spindle (Steel) - A SH 1E-S3 Spindle (Bronze) - A Z 5" Spindle - A-54950; 5 32" Spindle - A SPINDLES The 1E-S2 flat spindle is supplied standard on all 1E rim cylinders. If marine application is necessary, request marine construction (1E-S3 bronze spindle and non ferrous materials supplied). A five (5) inch spindle is available for thick door applications. MORTISE SERVICE EQUIPMENT ED211 ED211 Mortise Cylinder Wrench ED212 The Best mortise cylinder wrench and test handle is an essential dual-purpose tool. The double end is used primarily to install or remove BEST mortise cylinders without marring the cylinder surface finish. The single end may be used to test the lock operation, as well as align the throw pins. To order specify: ED211 mortise cylinder wrench. ED212 Mortise Cylinder Cam Assembly Tool Mortise cylinder cams are quickly changed with the use of this tool. Approximate length 1 3 4". To order specify: ED212 assembly tool. ED221 Mortise Cylinder Thread Repair Die Tool for re-threading " diameter cylinders. To order specify: ED221 thread repair die. ED222 Cylinder Cam Testing Tool Special cylinder / wrench assembly. Screws provide rapid means to install cams for testing. To order specify: ED222 cam testing tool. ED225 Hole Tap For " Mortise Cylinder Tap tool used to re-thread housing threads for 1E Mortise Cylinders. A40095 Standard Throw Pins SPINDLES SPINDLES RIM CYLINDERS 3

5 HEAVY DUTY LOCKS - LEVERS HEAVY DUTY CYLINDRICAL LOCKS LEVERS

6 TABLE OF CONTENTS & FEATURES TABLE OF CONTENTS Page Features...2 Specifications...3 How to Order...3 Trim Variations...4 Options/Features...5 Service Equipment...5 FEATURES 1. For versatile applications, lever by knob trim variations are available. Page Function Descriptions Shipping Weights K Sample Specifications Patented Keying Deadlocking Latches Strikes & Door Preparation Rose locking pin and rose assembly design offers great torque resistance. It prevents the locking pin from twisting, bending, or breaking under attack. 3. The innovative design of the slotted key release cam and locking lug assembly create maximum attack resistance. Even though damaged, the lock still allows key access. In addition, the lever is fully functional from the inside. The hub-mounted torsion spring and strong retractor springs help prevent lever sag and offer a smooth and snappy operation. 4. Strong through-bolt mounting studs increase torque resistance. Heavy rose liner material is highly attack resistant. 5. Strong retractor springs provide resistance to lever sag. 6. New zinc hubs with a shrouded locking lug, guaranteeing higher quality and increased torque resistance. 7. The outside lever sleeve is a seamless one piece construction made of a hardened steel alloy that provides additional reinforcement in the locking lug slot. 8. Lost Motion feature available allowing lever movement between 45º 60º without engaging retractor assembly. 9. Interchangeable core allows for quick re-keying and customized masterkeying K EXPLODED 2 H E AV Y D U T Y L

7 Certifications UL Listed: Listed by Underwriter's Laboratories for use on 3 Hr, A label single swinging doors (4'x10'). GYJT Builders Hardware-single point locks or latches. American National Standard: ANSI A156.2, Series 4000 Grade 1 California Fire Code NOA ANSI A Listed. Finish (BHMA) US DESCRIPTION bright brass satin brass bright bronze satin bronze B oxidized satin bronze, oil rubbed bright nickel plated satin nickel plated flat black bright chromium plated D satin chromium plated dark bronze SPECIFICATIONS Latch Solid brass 9 /16" throw. Front 2 1 /4" x 1 1 /8" beveled. Lever handles Lever handles are a high-quality zinc alloy. Trim components are brass or bronze. Body is approximately 1 5 /8" in diameter; Handle is approximately 4 3 /4" long (from center-line of chassis). #14 and #15 levers conform to California Administrative Code Title 19 and Title 24. All three styles of levers conform to the Illinois Accessibility Standard. Mounting In addition to standard door preparation (ANSI A115.2 for 1 3 /4" doors), two additional holes are needed for through-bolts. Through-bolts require two 5 /16" diameter holes located at 12 o'clock and 6 o'clock positions. A drill jig is provided to insure accuracy of the holes. (see KD303 page 5). Projection on door Approximately 2 3 /4" when mounted on 1 3 /4" door. Roses C -3" Convex D -3 1 /2" Convex K -3" Convex - no ring L -3 1 /2" Convex - no ring Strike STK: Conforms to ANSI A115.2 (2 3 /4" x 1 1 /8" with curved lip & box). S3: Conforms to ANSI A115.2 for 1 3 /4" doors (4 7 /8" x 1 1 /4" with curved lip). S3-7/8: Conforms to ANSI A115.2 for 1 3 /4" doors (4 7 /8" x 1 7 /8" flat) SPECIFICATIONS Backset 2 3 /4" standard, 3 3 /4" and 5" available. Chassis Critical latch and chassis components are brass or corrosion-treated steel. 2 1 /16" diameter to fit 2 1 /8" hole in door (Conforms to ANSI A115.2). Lost Motion feature available as an option. (see page 5 for options/features) Door thickness Available for 1 3 /4" to 2 1 /4" doors. Spacers available for 1 3 /8" doors. Products protected by one or more of the following patents: U.S.: Canada: D290,085 4,428,212 4,428,570 1,184,773 4,843,852 4,318,558 4,779,908 1,194,057 4,262,507 4,496,178 5,794,472 1,229,358 5,116,170 5,590,555 Other products patent pending. HOW TO ORDER 93K 7 AB 15 D S3 626 Backset Core Function Lever Rose Strike Available Options Housing Code Style Style Package Finishes* 93K 2 3 /4" 94K 3 3 /4" 95K 5" 0 keyless 7 7 pin housing accepts all Best cores AB entrance D storeroom L privacy N passage R classroom Etc. pages curved return 15 contour angle return 16 curved no return C 3" convex D 3 1 /2" convex K 3" convex - no ring L 3 1 /2" convex - no ring STK 2 3 /4" ANSI S3 4 7 /8" ANSI S3 7/8-7 /8" flat strike AL,TL options pages 4-5 pages 4-5 page 11 page 5 * Handles are made from a zinc alloy, and have been plated to be equivalent in appearance to the finishes listed. For information on 9K non IC products please refer to Best s non-ic keying products brochure. AL abrasive lever LL lead lined LM lost motion RQE request to exit SH security head screws TL tactile lever 3/4 3 /4" throw latch 7/8" LTC flat lip strike NOTE: specify inside (I), outside (O), or both (B) for HOW TO ORDER O C K - L E V E R S 3

8 TRIM VARIATIONS TRIM VARIATIONS 14C 15C 16C 14D 15D 16D 14K 15K 16K 14L 15L 16L DIMENSIONS LEVER & TRIM DIMENSIONS 4 H E AV Y D U T Y L

9 OPTIONS/FEATURES Abrasive Lever Option Besides complying with a wide variety of accessibility codes and ordinances, Best Access Systems lever handles are available with a special abrasive feature. Abrasive strip on the lever immediately identifies warnings on doors to hazardous areas for the blind. To order: Designate "AL" on How to Order (page 3). Note: abrasive strip is available on all levers, except #14, #15, #16 levers in 613 finish. Lost Motion Feature The Lost Motion feature allows the lever handle to move 45 degrees from parallel to the horizontal plane without engaging the latchbolt assembly. When the lockset is in the locked mode, this feature makes over-torque or overlever-age abuse more difficult to achieve. To order: designate "LM" on How to Order (page 3). Non IC Lever Option The 9K heavy duty cylindrical lock may be adapted to existing keying systems by using a special retrofit lever and throw member that will accept 6 pin single shear-line cylinders from non BEST manufacturers. No internal modifications are required to adapt the 9K to cylinders from the following manufacturers: Corbin-Russwin, Medeco, Sargent, Schlage, Yale. Refer to non-ic Best keying products brochure for more details. RQE Feature The 9K lever handle cylindrical can be supplied with a request-to-exit (RQE) switch. A normally open switch provides momentary switch closure when the inside lever is rotated. To order: designate "RQE" on How to Order (page 3). Tactile Lever Option Tactile levers may be used in areas where improved grip is required or as a warning in hazardous areas. Grooves are machined into the back of the hand grasp portion of the lever to improve grip and/or to provide a sensory warning in hazardous areas. This option can be used for Blind, Safety or Accessibility applications. To order: Designate "TL" on How to Order (page 3). KD303 THROUGH-BOLT DRILL JIG Special accessory jig aids in aligning 5 /16" holes for through-bolt mounting. Install the latch first, then insert jig in 2 1 /8" bored hole, align with door edge and drill with 5 /16" drill bit. A drill jig is included 1 per every 9 locksets with your order. Additional jigs are available upon request. To order: designate KD303. KD304A BORING JIG KITS The KD304A jig kit is made for boring cut outs in wooden doors for ANSI A156.2 series cylindrical/tubular locksets, doors 1 3 /8" to 2 1 /4" thick. The KD304A kit includes the boring jig (to drill wood doors for 2 3 /8", 2 3 /4", 3 3 /4" and 5" backsets), adaptor for 3 /8" drill chuck, KD309: 2 1 /8" bit, KD318: 1" dia. x 9" bit, KD312: face plate marking chisel 1", KD315: face plate marking chisel 1 1 /8", and the KD325: strike plate locating pin. To order: complete kits specify KD304A Kit. All of the individual kit parts listed above may be ordered separately except for the adaptor chuck and jig. SERVICE EQUIPMENT KD303-9K KD304A (Complete kit) OPTIONS/FEATURES SERVICE EQUIPMENT KD315 FACE PLATE MARKING CHISEL KD325 PLATE LOCATING PIN The KD315 faceplate marking chisel locates the mortising for the faceplate of ANSI A156.2 (1 1 /8" x 2 1 /4" ) cylindrical lockset. A strike plate locating pin KD325 is available for use in conjunction with ANSI A156.2 cylindrical locksets. To order: designate KD312 faceplate marking chisel (1"), KD315 faceplate marking chisel (1 1 /8"), KD325 strike plate locating pin. KD315 KD325 KD317 SPANNER WRENCH KD340 SPRING TOOL All 9K locksets require the use of KD317 spanner wrench for door mounting. This tool is included 1 per every 9 locksets with your order. If more are needed, designate KD317 on your order. The KD340 lever return spring tool with its unique design feature is used when replacing the 9K lever return spring. To order: designate KD340. KD317 Spanner Wrench KD340 Spring Tool O C K - L E V E R S 5

10 FUNCTIONS FUNCTIONS Function & Diag. Description Outside Lever Inside Lever (ANSI No.) Latch operated by Locked by Unlocked by Locked by Unlocked by Single Keyed AB Entrance Cannot be locked Always unlocked F109 D Storeroom Rotating the inside lever, Rotating the outside lever only when the inside push button is out, Turning the key in the outside lever Turning the key in the outside lever, Rotating the inside lever Pushing the inside button, Pushing and turning the inside button. Turning the button keeps the outside lever locked until the button is turned back Always fixed Turning the key in the outside lever, (only when the button is not turned) Rotating the inside lever, (only when the button is not turned). Closing the door (only when the button is not turned) Cannot be unlocked Cannot be locked Always unlocked F86 Service Station E F92 Hotel Guest Rm. H F93 Hotel Guest Rm. HJ Indicator Included No Indicator Classroom R F84 Dormitory T F90 Double Keyed* Corridor C F88 Storeroom * G Rotating the inside lever, Rotating the outside lever-only when the inside push button is out. Turning the key in the outside lever Rotating the inside lever, Turning the key in the outside lever-only when the inside push button is out, Removing the core with a control key and using a special emergency key Pushing the inside button projects an occupied indicator in the outside lever and blocks all operating keys. Rotating the inside lever, Turning the key in the outside lever-only when the inside push button is out, Removing the core with a control key and using a special emergency key Pushing the inside button blocks all operating keys, but no occupied indicator is projected. Rotating the inside lever, Turning the key in the outside lever, Rotating the outside lever when not locked by key Rotating the inside lever, Rotating the outside lever when not locked by key or push button Rotating the inside lever, Rotating the outside lever when not locked by key, Turning the key in the outside lever Rotating the outside lever when not locked by key, Rotating the inside lever when not locked by key Pushing the inside button, Pushing and turning the inside button. Turning the button keeps the outside lever locked until the button is turned back Always fixed Always fixed Turning the key in the outside lever Turning the key in the outside lever, Pushing the button on the inside lever Turning the key in the inside lever Turning the key in the inside lever, Turning the key in the outside lever Turning the key in the outside lever, Rotating the inside lever, Closing the door-only when the button is not turned, Turning back the slotted button Key block feature is released by: Rotating the inside lever, Closing the door Key block feature is released by: Rotating the inside lever, Closing the door Turning the key in the outside lever Turning the key in the outside lever, Rotating the inside lever (only when locked by push button), Closing the door (only when locked by push button) Turning the key in the inside lever Turning the key in the inside lever, Turning the key in the outside lever Cannot be locked Cannot be locked Cannot be locked Cannot be locked Cannot be locked Cannot be locked Always unlocked Always unlocked Always unlocked Always unlocked Always unlocked Always unlocked Turning the key Turning the key in the inside lever, in the inside lever, Turning the key Turning the key in the outside in the outside lever lever F91 Turning the key in either the inside or the outside, locks or unlocks both sides. *ATTENTION: Locksets that secure both sides of the door are controlled by building codes and the Life Safety Code. In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal. 6 H E AV Y D U T Y L

11 FUNCTIONS Function & Diag. Description Outside Lever Inside Lever (ANSI No.) Latch operated by Locked by Unlocked by Locked by Unlocked by Double Keyed (Continued) Intruder Rotating inside lever, Turning key in the inside Turning key in the inside Cannot be locked Always unlocked Rotating outside lever lever, lever, IN only when not locked by Turning the key in the Turning the key in the outside inside or outside key outside lever lever FUNCTIONS Communicating* S F80 Institutional* W F87 Turning the key in the Turning the key in the outside inside lever, lever Turning the key in the outside lever, Rotating the inside or outside lever (if unlocked) Turning the key in either lever, locks or unlocks its own lever independently. Turning the key in the inside lever, Turning the key in the outside lever Always fixed Turning the key in the outside lever Cannot be unlocked Turning the key in the inside lever Always fixed Turning the key in the inside lever Cannot be unlocked Keyless Privacy L F76 Rotating the inside lever Rotating the outside lever only when the inside push button is out Pushing the inside button Rotating the outside slotted button, Rotating the inside lever, Closing the door. Cannot be locked Always unlocked N Passage Rotating the inside lever, Rotating the outside lever Cannot be locked Always unlocked Cannot be locked Always unlocked F75 NX Exit Rotating the inside lever Always fixed Always fixed Cannot be locked Always unlocked F89 P F77 Patio Rotating the inside lever, Rotating the outside lever only when the inside push button is out Pushing the inside button Rotating the inside lever, Closing the door Cannot be locked Always unlocked Exit Rotating the inside lever Cannot be locked Always unlocked Y Single Dummy Trim This is a single, surface-mounted lever for an inactive door or a non-latching door 1DT Double Dummy Trim This is a through bolt mounted pair of matching levers for an inactive door or a non-latching door 2DT *ATTENTION: Locksets that secure both sides of the door are controlled by building codes and the Life Safety Code. In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal. O C K - L E V E R S 7

12 FUNCTIONS FUNCTIONS Outside Lever Inside Lever (ANSI No.) Locked by Unlocked by Locked by Unlocked by Function & Diag. Description Latch operated by Electromechanical Electrically Rotating the inside lever, Locked Rotating the outside lever DEL only when power is off, Turning the key in the outside lever Applying 24 Volts DC. Outside lever remains locked only while power is on Switching off 24 Volts DC Cannot be locked Always unlocked Electrically Unlocked DEU Rotating the inside lever, Rotating the outside lever only when power is on, Turning the key in the outside lever Switching off 24 Volts DC Applying 24 Volts DC Outside lever remains unlocked only while power is on Cannot be locked Always unlocked Special Dormitory or Storeroom A F81 Office B F82 Closet or Storeroom DZ Rotating the inside lever, Rotating the outside lever only when inside turn button is in unlocked position, Turning the key in the outside lever Turning the inside button NOTE: Turn button must be manually rotated to unlock the outside lever. Rotating the inside lever, Rotating the outside lever only when inside push button is out, Turning the key in the outside lever Pushing the inside button Turning the inside button Turning the key in the outside lever, Rotating the inside lever Cannot be locked Cannot be locked Always unlocked Always unlocked NOTE: Push button is released by turning the key in the outside lever, OR rotating the inside lever. Closing the door does not release the push button. Turning the key in the outside lever, Turning the inside closet turn knob Always fixed Cannot be unlocked Closet turn knob cannot be locked Closet turn knob always free Entrance or Office EA Rotating the inside lever, Rotating the outside lever only when inside push button is out, Turning the key in the outside lever Pushing the inside button, Pushing and turning the inside button. Turning the slotted button keeps the outside lever locked until the button is turned back Turning the key in the outside lever, Rotating the inside lever, Turning the slotted button back Cannot be locked Always unlocked Closet or Storeroom RZ Turning the key in the outside lever, Turning the inside closet turn knob, Rotating the outside lever when not locked by key Turning the key in the outside lever Turning the key in the outside lever Closet turn knob cannot be locked Closet turn knob always free XD Special* Turning the key in the inside lever Always fixed Cannot be unlocked Always fixed Cannot be unlocked XR Special* Turning the key in the inside lever, Rotating the inside lever when not locked by key Always fixed Cannot be unlocked Turning the key in the inside lever Turning the key in the inside lever *ATTENTION: Locksets that secure both sides of the door are controlled by building codes and the Life Safety Code. In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal. 8 H E AV Y D U T Y L

13 FUNCTIONS Function & Diag. Description Outside Lever Inside Lever (ANSI No.) Latch operated by Locked by Unlocked by Locked by Unlocked by Special (Continued) Exit * Turning the key in the inside Always fixed Cannot be YD lever unlocked FUNCTIONS YR Special * Turning the key in the inside lever, Rotating the inside lever when not locked by key Turning the key in the inside lever Turning the key in the inside lever DR RD Special * Special * Rotating the inside lever only when not locked by key, Turning the key in the outside lever, Turning the key in the inside lever Rotating the outside lever only when not locked by key, Turning the key in the outside lever, Turning the key in the inside lever Always fixed Turning the key in the outside lever Cannot be unlocked Turning the key in the outside lever Turning the key in the inside lever Always fixed Turning the key in the inside lever Cannot be unlocked LL Hospital Privacy Rotating the inside lever, Rotating the outside lever only when the inside push button is out Pushing the inside push button Turning the turn button in the outside lever, Rotating the inside lever, Closing the door Cannot be locked Always unlocked Communicating* Rotating the inside lever-only Turning the inside turn Turning the inside turn button when the outside turn button is button M in the unlocked position, Rotating the outside lever-only when the inside turn button is in F78 the unlocked position NOTE: Do not use this function for rooms that have no other entrance. Exit Rotating the inside lever, Turning the inside turn Turning the inside turn button Q Rotating the outside lever-only button when the inside turn button is in the unlocked position F83 Closet Rotating the outside lever, Turning the inside closet turn Z knob Turning the outside turn button Cannot be locked Cannot be locked Always unlocked Closet turn knob cannot be locked Turning the outside turn button Always unlocked Closet turn knob is always free *ATTENTION: Locksets that secure both sides of the door are controlled by building codes and the Life Safety Code. In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal. SHIPPING WEIGHTS The chart is the approximate shipping weight for the standard 9K functions locksets. This weight includes the weight of the lockset with the #15 style lever, K style rose, latch, strike package, and box. Listed separately are the approximate weights for with core and less core shipments. LOCK CASE SHIPPING SHIPPING FUNCTION QUANTITY WEIGHT- WEIGHT- NOMENCLATURE WITH CORE LESS CORE Y 9 31 lbs. N 9 40 lbs. L,NX,P 9 40 lbs. AB,D,E,H,HJ,R,T 9 42lbs. 40 lbs. C,G,IN,S,W 9 44 lbs. 40 lbs. SHIP WEIGHTS O C K - L E V E R S 9

14 SAMPLE SPECIFICATIONS ACCEPTABLE MANUFACTURERS A. Locksets and Latchsets Stanley/Best - No Substitution. 1. Locksets and latchsets: ANSI A156.2, Series 4000, Grade 1 UL listed, extra heavy-duty cylindrical type. 2. Backset 2 3 /4 inches (70mm) 3. Interchangeable core 7-pin: [Restricted keyway] [Patented] [Standard] [ ]. 4. Locksets to have anti-rotational studs that are through-bolted. 5. Keyed lever with no exposed keeper hole. 6. Each lever to have independent spring mechanism designed to control lever only. 7. Outside lever sleeve seamless, 1-piece construction, hardened steel alloy. 8. Keyed Lever: Removable only after core is removed, by authorized control key, to allow access to knob keeper. 9. Hub, side plate, anti-rotational studs 1-piece casting with shrouded locking lug. B. Keys and Keying A. Cylinders: 7-pin, interchangeable core and keyed into a [New] [Existing] factory registered Grand Masterkey System with a [Standard] [Restricted] [Patented] keyway. 1. Acceptable Material: Cylinders as manufactured by Best Access Systems. B. Provide construction cores and keys during construction period. Construction control and operating keys and cores are not part of permanent keying system or furnished on same keyway (or key section) as permanent keying system. C. Permanent Keys and Cores: Prepare permanent cores and keys in accordance with keying schedule. [Stamp with applicable key mark for identification.] [Do not stamp.] [ ]. D. Provide Grand Masterkeys, Masterkeys and other Security Keys. E. Furnish keys in the following quantities: 1. [4] [ ] each Grand Masterkeys. 2. [4] [ ] each Masterkeys per set. 3. [2] [ ] each Change keys each keyed core. 4. [6] [ ] each Construction masterkeys. 5. [2] [ ] each Control keys. 6. Install permanent cores in locksets. F. Return construction cores to [{Best} factory representative] [Hardware manufacurer s representative]. MX8 PATENTED KEYING SYSTEM MX8 PATENTED KEYING SYSTEM One of the greatest threats to key control within your facility is the unauthorized duplication of keys; one simple solution is the use of the MX8 Patented Keying System by Stanley-Best Access Systems a patent-protected keying system. Very seldom can a single product meet all of your exact needs, and often your level of convenience must be sacrificed to fit the capabilities of the product. The MX8 Patented Keying System provides you with an significant amount of flexibility, enabling a solution that fits your unique balance between security and convenience. The MX8 Patented Keying System is available in two series of keyways, the M Series and the X Series. Each series offers a different blend of features to help you maximize convenience while optimizing your security. MX8 Key & Core The MX8 Patented Keying System has the ability to provide geographic exclusivity to the customer. M Series Keyway Features Patented keys operate both MX8 and Standard BEST cores (backward compatibility) with existing BEST keyways (JKLM only). Standard keys do not operate MX8 cores. Available in large bow, long blade, and long nose key blanks to work with special applications. Available in core designs for use in special application locks, such as high security mortise, hotel cylinders, and glass display-case locks. Utilizes the same combinating kits and key cutting equipment as the Standard BEST keyways. M Series keys operate MX8 cores and Standard (non-patented) BEST cores. Standard key blanks do not operate MX8 cores. X Series Keyway Features Distinctive key design includes thicker key blanks with larger bow for added strength and easier handling. Keyways are unique to MX8 Patented Keying System offering even higher key duplication protection. Requires only minor modifications to key cutting equipment to accommodate new keyways. X Series keyways utilize the standard combinating kit, minimizing the expense of system changeover. X Series keys only operate MX8 cores. 10 H E AV Y D U T Y L

15 8KL3 Deadlocking Latch Bolt throw 9 /16" Backset 2 3 /4" Front 2 1 /4" x 1 1 /8" beveled. Tube To fit 1" diameter hole in door edge. To order: (wit h unit) designate 93K on How to Order (page 3). To order: (without unit) designate 8KL3-SL (Spring Latch) or DL (Deadlocking Latch) and finish. 8KL4 Deadlocking Latch Bolt throw 9 /16" Backset 3 3 /4" Front 2 1 /4" x 1 1 /8" beveled. Tube To fit 1" diameter hole in door edge. To order: (with unit) designate 94K on How to Order (page 3). To order: (without unit) designate 8KL4-SL" (Spring Latch) or DL (Deadlocking Latch) and finish. DEADLOCKING LATCHES 8KL5 Deadlocking Latch Bolt throw 9 /16" Backset 5" Front 2 1 /4" x 1 1 /8" beveled. Tube To fit 1" diameter hole in door edge. To order: (with unit) designate 95K on How to Order (page 3). To order: (without unit) designate 8KL5-SL (Spring Latch) or DL (Deadlocking Latch) and finish. DEADLOCKING LATCHES STRIKES STRIKES 8KS3-7/8 8KS3 7/8 Flat Strike Dimension: Conforms to ANSI A115.2 for 1 3 /4" doors (4 7 /8" x 1 7 /8" flat) To order: (with unit) designate S3-7/8 on How to Order (page 3). To order: (without unit) designate 8KS3-7/8 and finish. 8KS3 8KS3 Strike Dimension: Conforms to ANSI A115.2 for 1 3 /4" doors (4 7 /8" x 1 1 /8" with curved lip). To order: (with unit) designate S3 on How to Order (page 3). To order: (without unit) designate 8KS3 and finish. 8KS2 8KS2 Strike (Supplied Standard) Dimension: Conforms to ANSI A115.2 for 1 3 /8" doors (2 3 /4" x 1 1 /8" with curved lip and box). To order: (with unit) designate STK on How to Order (page 3). To order: (without unit) designate 8KS2 and finish. STRIKES & DOOR PREPARATION STRIKES & DOOR PREP. STK strike (standard) S3 strike 9K door preparation with through-bolt mountings O C K - L E V E R S 11

16 HEAVY DUTY CYLINDRICAL LOCKS LEVERS For more information on Stanley Security Solutions products, services, and office locations visit our web site at Product information contained in this catalog has been com piled and presented with as much care and com plete ness as is reasonably possible. Errors or mistakes may be present, and in many cases, reliance has been placed on information supplied by other manufacturers which may be in error or which may be subject to changes or mod i fi ca tions by the man u fac tur er with out no tice and without obligation. Therefore, no guar an tee can be made or should be assumed or implied with regards to product in for ma tion con tained in this catalog. Stanley Security Solutions, Inc E. 75th Street Indianapolis, Indiana Stanley Security Solutions, Inc. and Stanley Logistics 7.5M R709FP BAS008

17 90 Series Surface Overhead Door Holders/Stops 90 Series Heavy-Duty Glynn-Johnson 90 series holders and stops are the most rugged models available for heavy-duty applications. The channel is surface-mounted to the door, most often with sex bolts, and the jamb bracket is surface mounted to the jamb, requiring minimal door and frame preparation. These versatile units can be used in conjunction with most surface-applied door closers. The provided templates allow for variable mounting positions, ranging from 85º to 110º Hold-Open/Stop angle. These templates are designed for installation in almost all types of doors, including doors with conventional butt-type hinges or specialty hinges. Four Models: 90H Series Hold-Open Model 90S Series Stop-Only Model 90F Series Friction Hold-Open Model 90SE Series Special Stop-Only Model Five Sizes: Simple Standardized Each model is available in five sizes Three Options: J Angle Jamb Bracket SHIM Blade Stop Shim Kits SOC Pin-in-Socket Security Screw Package Unmatched Convenience: Non-Handed Improved Compatibility with Door Closers Single-Acting Doors Interior/Exterior Applications Durable Easy to Install Improved Corrosion Resistance Function Conversion Kits Available 14 Materials and Finishes: In 300 series Stainless Steel, Brass and Steel substrates, these models are available in the largest selection of finishes in the industry. Stainless Steel models offer the highest resistance to corrosion. Available in the following finishes: Finish Description US3 Polished Brass US4 Satin Brass US10 Satin Bronze US10B Oil Rubbed Bronze US32 Polished Stainless Steel US32D Satin Stainless Steel SP4 Powder Coat Brass SP10 Powder Coat Bronze SP28 Powder Coat Aluminum SP313 Powder Coat Dark Bronze SPBLK Powder Coat Black 652 Chrome-like Coating Models Glynn-Johnson 90 series door holders and stops provide long-lasting protection for doors, frames and hardware. All models incorporate a heavy-duty channel/slide-arm design and offset jamb bracket. This unique design allows for simple field modification of functions, should user requirements change. 90H Series Hold-Open (Suffix H) Hold-Open models provide a convenient method of holding the door open at a predetermined position for short or long periods of time, permitting an unobstructed traffic flow through the opening. The Hold-Open function can easily be turned on or off by simply rotating the serrated knob on the bottom of the channel. This knob engages the Hold-Open mechanism, allowing the door to be held open at a predetermined position ranging from 85º to 110º. When the knob is flipped over, it acts as a stop and shock absorber. The tension on the Hold-Open mechanism can be adjusted using a phillips screwdriver to offset air currents or other exterior conditions. The Hold-Open tension adjustment is located on the top of the slider in the channel. 90S Series Stop-Only (Suffix S) When the Hold-Open function is not a requirement, Stop-Only models provide a reliable method of door control. Stop-Only models provide the same shock-absorbing capability as Hold-Open models. The Stop-Only model may be used on fire doors. 90F Series Friction Hold-Open (Suffix F) Friction Hold-Open models are ideal for patient room doors, wardrobe and closet doors or similar applications where multiple Hold-Open positions are desired. The friction tension can be adjusted through the top of the channel using an allen wrench. The friction tension adjustment is located on the top of the slider in the channel.

18 90SE Series Special Stop-Only (Suffix SE) When Stop-Only models are used in conjunction with single-point, Hold-Only electronic door closers, the Stop-Only function may be ordered without the shock-absorbing mechanism. Used as an auxiliary stop, these models prolong the life of the closer. The stop location is adjusted using an allen wrench on the stop block located in the channel. Note: Caution should be taken when using this option in other applications, as the elimination of the shock-absorbing spring can put added stress on the door and frame. Application Information UL Classification The 90 series Stop-Only models are classified by Underwriters Laboratories (UL) as Miscellaneous Fire Door Accessories. This classification applies to use on either Hollow Metal Fire Doors or Wood Fire Doors. These units may be used on doors of any rating. As a reminder, the Miscellaneous Fire Door Accessories (GVUX) section is defined by UL as: Miscellaneous fire door accessories are intended in the individual Listings. The accessories have been investigated to determine that when installed in accordance with the manufacturer s instructions, the accessories do not adversely affect the fire rating of the fire door and/or fire door frames. Dead-Stop Templating: Dead-stop templating is recommended for applications where a wall or similar obstruction is placed at an opening angle of 110º or less (i.e., doors that open back-to-back). Dead-stop templating can be applied to Hold-Open, Stop-Only and Friction models. The Dead-Stop position is the point at which the shock-absorbing spring is fully compressed. Therefore, when Dead-Stop Templating is used, the initial degree of opening will be 5º to 7º less than the Dead-Stop opening. Example: If the holder is templated to a 100º Dead Stop, the door will hold open at an angle between 93º and 95º but no further than 100º Note: Do not use dead-stop templating on the 90SE Series since there is no shock-absorbing spring. Environmental Considerations: Environmental factors should always be considered when specifying overhead holders and stops. Doors that are positioned on a building s exterior or subject to corrosive conditions should be equipped with a holder constructed primarily of stainless steel or brass materials. For interior applications, steel is acceptable, though brass substrates generally provide a more attractive architectural-grade finish. Function Conversion Kits FK90H Converts a 90F or a 90S unit into a 90H unit. To order specify FK90H. FK90F Converts a 90H or a 90S unit into a 90F unit. To order specify FK90F. FK90SE Converts a 90H, 90F or a 90S unit into a 90SE unit. To order specify FK90SE Finish. No kit is needed to convert a 90H or 90F unit into a 90S unit. Options Suffix J (Angle Jamb Bracket): An angle jamb bracket is available for converting standard models to hinge-side or flush transom mounting. The angle jamb bracket affixes to the standard jamb bracket. If ordered with the unit add suffix J. If needed separately order 90J by finish needed. Suffix SOC (Pin-in-Socket Security Screws): A screw package with pin-in-socket screws for mounting the door bracket and the jamb bracket is provided instead of the standard screw package. Suffix SHIM (Blade Stop Shims): Shim kits are available in 3 sizes 90 SHIM1 is a 1/4" Shim Kit 90 SHIM2 is a 1/2" Shim Kit 90 SHIM3 is a 3/4" Shim Kit If ordered with overhead, add suffix SHIM (1, 2 or 3). If needed separately order 90 SHIM (1, 2 or 3) Finish. 15

19 90 Series Surface Overhead Door Holders/Stops 1-7/8" 1-3/16" 1/4" 1' 3-1/4" 1/4" 1-1/2" 1/4" 2-5/8" 1-1/2" 90 Series Sizing Chart BUTTS/OFFSET PIVOTS CENTER HUNG DOOR STOP HOLD DOOR STOP HOLD SIZE OPENING ONLY OPEN FRICTION OPENING ONLY OPEN FRICTION /16" 27" 902S 902H 902F 27-1/16" 33" 902S 902H 902F /16" 33" 903S 903H 903F 33-1/16" 39" 903S 903H 903F /16" 39" 904S 904H 904F 39-1/16" 45" 904S 904H 904F /16" 45" 905S 905H 905F 45-1/16" 51" 905S 905H 905F /16" 51" 906S 906H 906F 51-1/16" 59" 906S 906H 906F BHMA/ANSI, A156.8 & FED. Spec. Cross Reference G-J Model BHMA* FED. Spec H C S C A F C02531 * First numeral (0) designates optional material. To specify: Brass material, change 0 to 1 (i.e. C12511) Stainless Steel material, change 0 to 5 (i.e. C52511) Steel material, change 0 to 8 (i.e. C82511) Note: This chart illustrates the most common types of hinging and door opening sizes. For unusual door details, contact Glynn-Johnson for availability. The template information on this page is for reference only and is not intended to serve as an installation template. For complete dimensional information, refer to Glynn-Johnson template book. 16

20 How to Order 90 4 H US32D J Overhead Series: 90 Size (Door Opening Using Butts or Offset Pivots): 2 (23-1/16" 27") 3 (27-1/16" 33") 4 (33-1/16" 39") 5 (39-1/16" 45") 6 (45-1/16" 54") Function: H F S SE Hold-Open Friction Hold-Open Stop-Only Special Stop-Only Finishes: US3 Polished Brass US4 Satin Brass US10 Satin Bronze US10B Oil Rubbed Bronze US32 Polished Stainless Steel US32D Satin Stainless Steel SP4 Powder Coat Brass SP10 Powder Coat Bronze SP28 Powder Coat Aluminum SP313 Powder Coat Dark Bronze SPBLK Powder Coat Black 652 Chrome-like Coating Options: J SHIM SOC Angle Jamb Bracket Blade Stop Shims SHIM1 1/4" Kit SHIM2 1/2" Kit SHIM3 3/4" Kit Pin-in-Socket Security Screws 17

21 Protection Plates A Hinges & Pivots B14 Pulls & Plates C Flush Bolts & Coordinators 8400 Series Protection Plates Door protection plates are available in.050 thick brass, stainless steel or aluminum; and 1/8 thick high impact polyethylene in clear or black. Bevel edge options; specify B4E for all four edges. Mounting screw pack furnished standard, 16 screws per pack. Optional screw packs are available for TEK or TORK screw heads. Refer to the following chart for ordering. Specify NMH for no mounting holes. (Not available on 8402) Specify NMH-A for no mounting holes with adhesive. (Not available on 8402) Specify CS for counter sunk mounting holes. Specify ERS prepped with extra row of screws. Kickplate Gasket Tape Tape is recommended when using a brass plate on a metal door to reduce tarnishing from electrolytic oxidation. One tape pack will cover an the perimeters of a 8 x 34 kickplate. Order 8401 Gasket Tape. D Latches, Catches & Bolts E Stops F Exterior Hardware 8400 Protection Plate 8402 (UL)* Protection Plate *UL mark appears in upper right corner. Factory supplied screws must be used. Number of screw packs required by plate size (specify TEK Screws or TORK screws) Finishes brass 24 x 48 max. size US Number US3 US4 US10 US10B US15 US26 US26D BHMA Finishes stainless steel US Number US32 US32D BHMA G Miscellaneous Hardware B14 Ives Architectural hardware products Finishes aluminum US Number US28 BHMA 628 Finishes plastic Clear and Black Residential Grade Kickplates available Carded only, finishes PA28, PA3, PA619, PA716, B3, B505, B619, B716

22 Protection Plates A Hinges & Pivots B18 Pulls & Plates C Flush Bolts & Coordinators D Latches, Catches & Bolts Mop Plates Kick Plates Protect the bottom of the pull side of door subject to cleaning and mopping procedures. Size Ranges:4 to 6 high, 22 to 48 wide Protect the bottom of the push side of doors subject to scuffing from foot traffic. Recommended for all doors subject to normal use (especially doors using a closer). Size Ranges: 8 to 24 high, 22 to 48 wide Stretcher Plates Armor Plates Protect doors at specific areas where consistent contact is made by stretchers, service carts or other equipment. Usually applied to push side of doors. Specify B4E Option for beveled edges. Size Ranges: 6 to 8 high, 22 to 48 wide Protect lower half of doors from abuse by hard carts, trucks and rough usage. Usually applied to push side of single doors and both sides of double acting doors. Size Ranges: 26 to 48 high, 22 to 48 wide G Miscellaneous Hardware F Exterior Hardware E Stops B18 Ives Architectural hardware products

23 Meets ANSI/BHMA , L Meets ANSI/BHMA , L /4 1/8 CLEARANCE 1-3/16 SIDE VIEW BODY 1/2 F40 MAX. DOOR CLEARANCE CLEARANCE FROM 9/16 to 1-1/16 FS9 FS40 FS41 FS42 FS43 Floor Stops Floor Stop & Semi-Automatic Holder Semi-automatic floor-mounted holders accommodates with door to floor clearance of 1-1/2 or less. Cast from heavy-duty brass. Activate holder by flipping the engagement tongue forward. When door is opened, the hook (mounted on door) engages the tongue. To release, push firmly on door to disengage tongue. Universal screw pack accommodates all types of floor and door construction. Dimensions Overall Height: 3-1/2 Base Dimensions: 2 wide x 3-1/2 long Finishes Ives Number US3 US4 US10 US10B US26 US26D BHMA Floor Stop & Automatic Holder Automatic door holders ideal for heavy-traffic situations that require a simple, fool-proof, Hold-Open device. Forged from brass. Unit is activated automatically when door is opened. A firm pull on door releases the mechanism. Strikes accommodate different door to floor clearances. Model numbers are determined by strike/door-to-floor clearances. Holder position on door is adjustable. Universal screw pack allows for installation in all types of door construction. Dimensions Door to Floor Clearance: FS40 1/2 or less FS41 9/16 to 1-1/16 FS42 1-1/8 to 1-9/16 FS43 1-5/8 to 2-1/16 Holder Dimensions: 3 Wide x 3-11/16 High Finishes brass Ives Number US3 US4 US10 US10B US26 US26D BHMA /4 CLEARANCE FROM 1-1/8 to 1-9/16 FS41 FS42 FS43 2-3/4 CLEARANCE FROM 1-5/8 to 2-1/16 Ives Architectural hardware products E7 A Hinges & Pivots B Pulls & Plates C Flush Bolts & Coordinators D Latches, Catches & Bolts E7 Stops F Exterior Hardware G Miscellaneous Hardware

24 Architectural Door Trim A Hinges & Pivots B6 Pulls & Plates C Flush Bolts & Coordinators Push Plate 8300 Pull Plate, Prep for Pull (less pull) Available Sizes 3 x x 15 4 x 16 6 x 16 8 x 16 Special sizes are available. Consult factory. Plates Cut for Cylinder or Thumbturns Plates are available with cutout for cylinder or thumbturn; standard cutout is 2 from top and centered on plates up to 4 wide. For plates wider than 4 cutout is located 2 from outer edge, specify LH or RH. When pull location interferes with standard cutout location a detail drawing should be furnished with the order. Standard cutout is 1-1/4 for cylinder and 3/8 for thumbturn. Specify CFC for cutout for cylinder or CFT for cutout for thumbturn. Finishes brass US Number US3 US4 US10 US10B US15 US26 US26D* D Latches, Catches & Bolts 2 2 CFC CFT 2 2 BHMA Finishes stainless steel US Number US32D* BHMA 630 CFC CFT Finishes aluminum US Number US28 BHMA 628 E Stops * Available with Antimicrobial Coating, use suffix AM G Miscellaneous Hardware F Exterior Hardware B6 Ives Architectural hardware products

25 Wall Bumpers A Hinges & Pivots B Pulls & Plates C Flush Bolts & Coordinators D Latches, Catches & Bolts WS406CVX & WS407CVX Meets ANSI/BHMA L22201 for brass, and L52101 for stainless steel. WS406CCV & WS407CCV Meets ANSI/BHMA L22251 for brass and and L52251 for stainless steel. WS406CVX Wall Bumpers WS406CCV WS407CVX WS407CCV Dimensions Base Diameter: 2-1/2 Base Thickness: 3/8 Overall Projection: 1 Constructed in sturdy yet economical wrought base of brass or stainless steel construction. Feature concealed tamper-proof mounting. Shipped factory preassembled backplate to reduce installation cost. Easy installation by inserting screwdriver through small hole in rubber. WS406CVX (406) convex rubber bumper, packed with wood screw and plastic anchor. WS406CCV (406-1/2) concave rubber bumper, which avoids damage to locks with projecting buttons, packed with wood screw and plastic anchor. WS407CVX (407) convex rubber bumper packed with screw and drywall anchor. WS407CCV (407-1/2) concave rubber bumper which avoids damage to locks with projecting buttons and is packed with screw and drywall anchor. Finishes brass Ives Number US3 US4 US5* US10 US10B US15 US15A** US26 US26D B716** BHMA * E12 Stops Finishes stainless steel Ives Number US32D BHMA 630 * only available on WS407CVX Slim-Pak of 15 ** available on WS407CCV or WS407CVX Slim-Pak of 15 G Miscellaneous Hardware F Exterior Hardware E12 Ives Architectural hardware products

26 Door Silencers Meets ANSI/BHMA , L Meets ANSI/BHMA , L03021 SR64 Dimensions Diameter: 1/2 Thickness: 1/8 Finishes GRY, TAN SR65 Dimensions Height: 3/4 Diameter: 3/8 Thickness: 1/8 Finishes GRY Door Silencer For use on metal frames featuring pneumatic design that, once installed, forms an air pocket to absorb shock and reduce noise of door closing. Tamper-proof once installed on the frame. Proper installation also eliminates door rattle and provides constant tension for door latches or locks. Packed in bags of 100. Grey Available in bulk pack of Each bag has an installation tool included. Door Silencer For use on wood frames, also feature pneumatic design to cushion shock and absorb noise. To prevent removal, a small brad should be driven into stop strip and through stem of silencer, as shown in the detail. Packed in bags of 100. A Hinges & Pivots B Pulls & Plates C Flush Bolts & Coordinators D Latches, Catches & Bolts SR66 Door Silencer Self Adhesive Rubber Silencers. Economical installation requires no drilling of frames. Packed two sheets of 50 (100 minimum). E23 Stops Dimensions Diameter: 1/2 Thickness: 1/8 Finishes BRN, GRY, WHT F Exterior Hardware G Miscellaneous Hardware Ives Architectural hardware products E23

27 Dust Proof Strikes DP1 DP2 Meets Meets ANSI/BHMA , L DP1 DP2 Dust Proof Strikes Designed for use with the bottom bolt of all flush bolts. Spring-loaded plunger returns to floor or threshold level anytime flush bolt is retracted, eliminating need to clean standard floor strikes. Strike hole is 3/4" Diameter and 1-1/8" Deep Dimensions DP1 Face Plate: 1-7/16" Diameter DP2 Face Plate: 1-5/8" W x 3-1/2" L x 1/8" Thick Body: 1-3/16" Diameter x 1-7/8" Deep Finishes Ives Number US3 US4 US10 US10B US26 US26D BHMA A Hinges & Pivots B Pulls & Plates C11 Flush Bolts & Coordinators D Latches, Catches & Bolts E F Stops Exterior Hardware G Miscellaneous Hardware Ives Architectural hardware products C11

28 Manual Flush Bolts Metal Doors A Hinges & Pivots B Pulls & Plates C10 Flush Bolts & Coordinators D Latches, Catches & Bolts Meets ANSI/BHMA A156.16, L UL Listed 90 Minute Fire Doors 8'0" x 10'0" FB458 Top or Bottom Bolts When the active door is opened, the lever can be moved to the up position, retracting the bolt and allowing the inactive leaf to be opened. When the inactive leaf is closed, the lever can be moved to the down position, projecting the bolt into the strike and securely locking the inactive leaf. Simplified installation in metal frames. Round bolt head requires only a punched hole. Use of strike optional. Special design of guide and flat sided bolt tip to prevent bolt rotation. Non-handed. Bolt tip is 1/2" diameter. Bolt throw is 3/4" with a 7/8" vertical adjustment. Bolt backset is 3/4" Standard Rod Length is 12", which is measured from the center of the flush bolt body to the bolt tip. Optional Rod Lengths available - 6", 9", 18" and 24" for fire rated Doors. Optional Rod lengths available - 6", 9", 18", 24", 30", 36" and 48" for non-fire rated doors. DP1 or DP2 optional dust proof strike available, see page C11. Dimensions Body Size: 1" Wide x 6-3/4" Long x 1-1/8" Deep Guide Size: 1" Wide x 2" Long x 5/64" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick Finishes Ives Number US3 US4 US5 US10 US10B US15 US26 US26D BHMA G Miscellaneous Hardware F Exterior Hardware E Stops C10 Ives Architectural hardware products

29 Hooks A Hinges & Pivots B Pulls & Plates C Flush Bolts & Coordinators D Latches, Catches & Bolts E Stops Meets ANSI/BHMA A L13113 for brass and L33113 for aluminum Meets ANSI/BHMA A L Coat & Hat Hook Decorative design is ideal for commercial and residential installations. Made from cast brass, cast aluminum or epoxy-coated aluminum. Dimensions Base: 1-5/8" High x 1-3/4" Wide Projection: 3-3/4" Overall Height, Brass: 4-3/4" Overall Height, Aluminum: 5" Finishes brass Ives Number B3 B4 B10 B10B B15 B26 B26D BHMA Finishes aluminum Ives Number A3 A26 A92 BHMA Coat & Hat Hook Especially designed to accommodate large hats. Made from solid brass or cast aluminum. Dimensions Base: 2-1/4" High x 1-3/8" Wide Projection: 3-5/8" Overall Height: 5-3/4" Finishes aluminum Ives Number A3 A10B A92 BHMA F Exterior Hardware 580 Ceiling Hook Ideal for use in closets, attached to underside of shelves, or in storage lockers. Made from cast brass or cast aluminum. Dimensions Base: 1" High x 1-7/8" Wide Projection: 2-1/4" G4 Miscellaneous Hardware Finishes Ives Number A3 A5 A10 A14 A15 A92 A716 BHMA G4 Ives Architectural hardware products

30 Architectural Door Trim 3/4 ROUND 1 ROUND 8302 Pull plate Available mounting Standard, F, G, H-I-L, or J see pages B15 and B16 Pulls have new heavy duty 5/16-18 mounting Plate 8102 Pull 3-1/2 x 15 6 centers 4 x 16 8 centers 6 x centers Finishes brass US Number US3 US4 US10 US10B US26 US26D* BHMA Finishes stainless steel US Number US32D* BHMA 630 Finishes aluminum US Number US28 BHMA 628 * Available with Antimicrobial Coating, use suffix AM 8303 Pull plate Available mounting Standard, F, G, H-I-L, or J see pages B15 and B16 Pulls have new heavy duty 3/8-16 mounting Plate 8103 Pull 3-1/2 x 15 8 centers 4 x centers 6 x 16 7 centers Finishes brass US Number US3 US4 US10 US10B US26 US26D* BHMA A Hinges & Pivots B7 Pulls & Plates C Flush Bolts & Coordinators D Latches, Catches & Bolts 1 FLATTED 1/2 ROUND Finishes stainless steel US Number US32D* BHMA 630 Finishes aluminum US Number US28 BHMA 628 * Available with Antimicrobial Coating, use suffix AM 8305 Pull plate Available mounting Standard or F see page B15 Pulls have 1/4-20 mounting 8300 Plate 8105 Pull 3-1/2 x 15 6 centers 4 x 16 8 centers 6 x centers Finishes brass US Number US3 US4 US10 US10B US26 US26D BHMA Finishes stainless steel US Number US32D BHMA 630 Finishes aluminum US Number US28 BHMA 628 * Available with Antimicrobial Coating, use suffix AM Ives Architectural hardware products B7 E F Stops Exterior Hardware G Miscellaneous Hardware

31

32

33

34

35 Door position switches 674-OH Overview Overhead door, floor mount magnetic switch Door position switches are used to detect the open or closed status of an opening and then send this status to a control panel. They come in a variety of shapes and sizes and are designed for monitoring door positions, roof hatches, gates etc. Concealed SPDT magnetic switches For wood doors and frames VDC Concealed/flush mount magnetic switches For aluminum, wood and hollow metal doors VDC UL Listed 7764 For hollow metal doors and frames VDC For wood doors and metal frames VDC HM Surface mount magnetic switches For aluminum, wood and hollow metal doors VDC UL Listed WD

36 Ordering information 674-OH - Overhead door floor mount Wood door and frame HM - Hollow metal door and frame WD - Wood door and metal frame Concealed/flush mount Surface mount Allegion, the Allegion logo, Schlage, and the Schlage logo are trademarks of Allegion plc, its subsidiaries and/or affiliates in the United States and other countries. All other trademarks are the property of their respective owners. About Allegion Allegion (NYSE: ALLE) is a global pioneer in safety and security, with leading brands like CISA, Interflex, LCN, Schlage and Von Duprin. Focusing on security around the door and adjacent areas, Allegion produces a range of solutions for homes, businesses, schools and other institutions. Allegion is a $2 billion company, with products sold in almost 130 countries. For more, visit Allegion , Rev. 08/15

37 Electrical power transfer Overview Features and benefits Electric power transfer provides a means of transferring electrical power from a door frame to the edge of a swinging door. The units are completely concealed when the door is in the closed position, and are ideally suited for installations involving abuse or heavy traffic. Two models are available; EPT-2, two 18 gauge wires and EPT-10, ten 24 gauge wires. UL Listed for use on fire doors UL listed as Miscellaneous Door Accessory Ball-and-socket joint construction provides cut and pinch protection for wiring Built for heavy traffic and high abuse openings

38 Door applications Up to 5" butt hinges 180 o swing " butt hinges 130 o swing. 6 butt hinges 110 o swing. 3 4" offset pivots 180 o swing. Not for use with swing clear hinges, center-hung pivots, pocket pivots or balanced doors. Door applications shown are for 1 ¾" door thickness, for all other applications contact Technical Support to confirm compatibility. Finishes SP28 (sprayed aluminum) SP313 (sprayed duranodic) Dimensions Housing EPT-2 EPT-10 PNT-1 9" X X (229mm X 32mm X 38mm) Two 18 gauge wires, up to 2 24VDC, with a 16 AMPS maximum surge Ten 24 gauge wires, up to 1 24VDC, with a 16 AMPS maximum surge 5/32" tubing To order, specify EPT-2, EPT-10 or PNT-1. Finish, SP28 or SP313. About Allegion Allegion (NYSE: ALLE) is a global pioneer in safety and security, with leading brands like CISA, Interflex, LCN, Schlage and Von Duprin. Focusing on security around the door and adjacent areas, Allegion produces a range of solutions for homes, businesses, schools and other institutions. Allegion is a $2 billion company, with products sold in almost 130 countries. For more, visit Allegion , Rev. 04/16

39 Sill Protection Automatic Door Bottoms - Heavy Duty Note: A = Aluminum D = Dark Bronze Anodized AA = Clear Anodized G = Gold Anodized #8 x 1.500"(38.1) SMS.916"(23.3).916"(23.3).924"(23.5).083" (2.2).083" (2.2) Anti Squeak Rubber 1.575" (40.0) Anti Squeak Rubber 1.901" (48.3) Anti Squeak Rubber 1.901" (48.3).371" (9.4).125"(3.2) #6x.500(12.7)SMS Max. Drop 1.00"(25.4) Max. Drop 1.00"(25.4) Max. Drop 1.00"(25.4) #8 x 1.500"(38.1) SMS.916"(23.3).916"(23.3).924"(23.5).083" (2.2).083" (2.2) Anti Squeak Rubber 1.575" (40.0) Anti Squeak Rubber 1.901" (48.3) Anti Squeak Rubber 1.901" (48.3).371" (9.4).125"(3.2) #6x.500(12.7)SMS Max. Drop 1.00"(25.4) Max. Drop 1.00"(25.4) Max. Drop 1.00"(25.4) #8 x 1.500"(38.1) SMS.916"(23.3).916"(23.3).924"(23.5) Magnet Magnet Magnet 1.575" (40.0) 1.901" (48.3) 1.901" (48.3) 1.250" (31.8).125" (3.2).371" (9.4).500" Rubber Extends (12.7) #6x.500(12.7)SMS Max. Effective Drop.562" (14.3) Double Neoprene Seal.500"(12.7) Max. Effective Drop.562"(14.3) Double Neoprene Seal.500"(12.7) Max. Effective Drop.562"(14.3) PRODUCT CATALOG #90 PAGE 18

40 Utility Thresholds Note: A = Aluminum B = Bronze D = Dark Bronze Anodized STST = Stainless Steel Thresholds can be ordered with E (Epoxy Abrasive), EL (Epoxy Abrasive Photoluminescent) or V3 (Full Body Strength) options..250" (6.4) (not shown).125" (3.2) 3.00" (76.2).125" (3.2).250" (6.4) 4.00" (101.6).125" (3.2) " (6.4) 5.00" (127.0).250" (6.4).125" (3.2) 6.00" (152.4).250" (6.4).125" (3.2) 7.00" (177.8).250" (6.4).125" (3.2) 8.00" (203.2).500" (12.7).187" (4.7).500" (12.7).187" (4.7) 3.00" (76.2) 4.00" (101.6).500" (12.7).187" (4.7) 4.00" (101.6).500" (12.7).187" (4.7) 4.00" (101.6).500" (12.7) 4.00" (101.6) PVC Break.135" (3.4) PRODUCT CATALOG #90 PAGE 4

41 Note: A = Aluminum R = Rubber Expansion Joints Adjustable Thresholds Thresholds can be ordered with E (Epoxy Abrasive) or EL (Epoxy Abrasive Photoluminescent) STST = Stainless Steel 1.00"(25.4) 84R 3.00"(76.2) 1.00" (25.4) 1.00" (25.4) 663 PSA 1.00"(25.4) Finished Wood Floor Finished Terrazzo or Asphalt Tile R Varies 2.00"(50.8) PSA Wood Flooring Bed plate by others Expansion Joint " (203.2).250" (6.4) 1.00"(25.4) 518N 8 wide rubber (optional) Directed to drains to evacuate water.365" (9.3).938" (23.8).375 (9.5) (52.4) Anchor with machine screw 10/24 Anchor with machine screw 1/4-20 PR OD U CT CA TA LOG # 9 0 PA GE 1 3 WW W. Z E RO IN TER N ATI ON AL. COM

42 Self-Adhesive Weatherstripping Note: N = Neoprene S-Bk = Silicone, Black S-Br = Silicone, Brown S-Cl = Silicone, Clear FS= Intumet Rubber Y-Bk = Polyvinyl, Black S-Wh = Silicone, White S-Gy = Silicone, Grey BIO = Antibacterial PSA* is equipped with 3M self-adhesive tape Gasketing, White All products are available with ZAG feature (Anti-Ligature) PSA PSA PSA.500" (12.7).250" (6.4) PSA.375" (9.5).187" (4.8) PSA.500" (12.7).187" (4.8).250" (6.4).425" (10.8).234" (5.9).500" (12.7) PSA.400" (10.2) PSA.500" (12.7).200" (5.1) PSA.500" (12.7).375" (9.5) PSA.437" (11.1).437" (11.1) PSA 1.00"(25.4).500" (12.7).250" (6.4) PSA.125" (3.2).500" (12.7) PSA.125" (3.2).500" (12.7) PSA.185" (4.7) 1.00"(25.4) PSA.094" (2.4) 1.250" (31.8).125" (3.2).375" (9.5) PSA.250" (6.4).125" (3.2).375" (9.5) PSA PSA.185" (4.7).750"(19.1).375" (9.5) 1.00"(25.4).400" (10.2).500" (12.7).125"(3.2).625" (15.9).625" (15.9).750" (19.1).625" (15.9) 1.00" (25.4).500" (12.7) 1.250" (31.8).625" (15.9) PRODUCT CATALOG #90 PAGE 33 INTERNATIONAL.COM