AUTO-BREEZE Cotton Candy Machine Instruction Manual Model #3052
|
|
- Gordon Burke
- 6 years ago
- Views:
Transcription
1 Part No Revised: August 2004 AUTO-BREEZE Cotton Candy Machine Instruction Manual Cincinnati, OH USA
2 Safety Precautions Auto-Breeze 2
3 INTRODUCTION Your Floss Machine warranty is described on the back page of this manual. This does NOT cover the motor bearings, since they can be damaged by the operator. After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty also does not cover damage that occurs in transit or damage caused by abuse or consequential damage due to the operation of this machine, since it is beyond our control. ELECTRICAL REQUIREMENTS The GOLD MEDAL 3052 requires 15 amp, 120 volt, 60 cycle electrical service. The power supply cord is equipped with a machine ground (the tubular prong on the male plug). For safety, always plug the machine into a grounded receptacle, which has been tested for proper polarity to insure electrical safety. BEFORE PLUGGING IN THE MACHINE Remove all padding and restraints. Loosen the two shipping bracket knobs. (As shown in figure 1 below.) This will allow the motor mount casting to float freely on the springs. Figure 1 Shipping bracket Knobs: Turn counter-clockwise to loosen. 3
4 CONTROLS AND FUNCTIONS POWER SWITCH Supplies power to the machine without turning on any components. Also acts as A Master on/off switch. Turning the power switch off will turn motor and heat off. (Power Switch is located on the side of the machine) CANDY SWITCH Turns motor and heat cycle on. Turning this switch off when finished making cotton candy allows the machine to start it s cooling cycle. Note: Motor will continue turning during the cooling cycle, and will stop turning after seconds. (Candy Switch is located on the front of the machine) OPERATING INSTRUCTIONS 1. With the CANDY SWITCH off, turn the POWER SWITCH on. The spinner head will not start to rotate. 2. With the spinner head stopped, pour sugar into the spinner head. Fill to about the 90% level, DO NOT over-fill. 3. Turn the CANDY SWITCH to on. The spinner head will rotate and heat, after about 45 seconds the machine will start to make cotton candy. 4. When the spinner head is empty, or to stop making cotton candy, turn the CANDY SWITCH off. The cooling cycle will start. When the cooling cycle completes, the spinner head will stop rotating. When the spinner head is stopped; re-fill with sugar, turn the CANDY SWITCH on, and continue to make cotton candy. SUGAR FOR YOUR COTTON CANDY Our ready to use FLOSSUGAR is the preferred sugar for your new cotton candy machine.our FLOSSUGAR gives you good rich colors, and great flavors, too. It is packed in handy half-gallon sealed cartons, with E-Z pour spout for filling your machine. FLOSSUGAR comes in 12 flavors, and you can easily change colors for greatest variety, and best sales. Today 99% of the sugar manufactured is Extra Fine Granulated which does have some small particles that can slip through the slots in the spinner head without being melted. You can use plain white cane or beet sugar. If this becomes objectionable, you can seek out Medium Coarse, or sanding sugars. The larger crystal size will require a little more heat to melt. Read the label on the bag of sugar today we see some Free Flowing sugar for restaurants, and it contains cornstarch, which will burn onto your spinner head, clogging it rapidly. We have also seen some cheap off-brand sugar which is a blend of sugar and dextrose or corn syrup. This product makes very poor cotton candy. Please make sure you get good sugar for your cotton candy machine. 4
5 INSTALLATION OF FLOSS STABILIZER
6 MAKING FLOSS Pick a cone; if it sticks in the stack of cones, twist it off the stack. Hold an inch or two of the pointed end of the cone between two fingers and a thumb. With a light flicking action, roll cone in the web of floss building up in the pan. Lift the cone up with the ring of floss attached and rotate the cone to wrap the floss. DO NOT roll floss while the cone is inside the pan. This will pack the floss too tightly. If the floss fails to stick to the cone, pass the cone near the spinner head to pick up a starter of melted sugar. Lift the cone out of the pan and wrap the floss with a "figure eight" movement of the hand. This leaves giant pockets and makes the final product appear larger. Make sure room humidity is not too high, or product will be "heavy". 1. Grip cone as shown. 2. Break into web of 3. Wind the sugar 4. Lift web of floss from the floss with the cone. onto the cone. pan and roll onto the cone DO NOT PUT HANDS OR OBJECTS IN ROTATING SPINNER HEAD. DO NOT FILL SPINNER HEAD WITH SUGAR WHILE IT IS ROTATING. OPERATOR SHOULD ALWAYS WEAR EYE PROTECTION. DO NOT PUT HANDS NEAR ROTATING SPINNER HEAD. USE FLOSS CONE TO COLLECT COTTON CANDY. 6
7 FLOATER ADJUSTMENT In operation, the floss will collect on the FLOSS STABILIZER. If the floss collects low on the stabilizer, twist the front (leading) edge of the leather floaters down. You get more lift and the floss will collect higher. Form leather floaters as shown. This creates a lifting action to float the floss higher on the outside wall of the floss pan. 7
8 MAINTENANCE INSTRUCTIONS Auto-Breeze 8
9 FLOSS BANDS AND ELEMENTS Disassembly and Removal 1. Remove all sugar from the head of the machine before disassembling. If the unit is inoperative, carefully turn the machine on its side and gently shake the sugar out. 2. Remove the four spinner cap retainer screws and spinner cap. In some cases, the sugar has caused the cap and band to stick together. Applying gentle pressure with the heel of the hand should free the parts for removal. 3. Remove the element lead wire retaining screws with a ¼" (9.5mm) nut driver and remove the element lead wires from the terminals in the floss head. This will allow the band and element to be removed. 4. Remove the band and element. If there is excessive sugar buildup, soak the band and element in hot water until the sugar dissolves. When the sugar has been removed, allow the band and element to dry over-night. 5. Re-assemble the floss head components, using the above steps for a reference. 9
10 TROUBLESHOOTING EXCESSIVE VIBRATION 1. If the equipment is new, verify that shipping bolts have been loosened and packing materials were removed from the machine. 2. When adding sugar to the floss head, always fill it 90% full to obtain a balanced condition in the head, and eliminate excessive vibration. DO NOT add sugar with motor running! 3. Check for stretched, or uneven suspension springs. 4. Run the sugar completely out, then check for foreign objects or sugar lumps in the head assembly. ORDERING SPARE PARTS 1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list. 2. When ordering, please include part number, part name, and quantity needed. 3. Please include your model name, serial number, and date of manufacture (located on the machine nameplate) with your order. 4. Address all parts orders to: Parts Department Gold Medal Products Co Medallion Drive Cincinnati, Ohio or, place orders at: (800) (513) Fax: (513) info@gmpopcorn.com Web Page: 10
11 CABINET ASSEMBLY FRONT VIEW For spinner head components see page
12 CABINET BOTTOM VIEW
13 PARTS LIST CABINET ASSEMBLY Item No. Part No. Description W Brush Holder Assy. - Complete (Includes below 3 items) *42138 Cap, Brush Holder *42436W Dual Brush Holder *55007 Carbon Brush Bell Housing Rubber Feet (Also used on bottom of the machine) Instruction Overlay Candy Switch Pilot Light Inspection Cover Shipping Bracket Knob Handle Stainless Steel Cabinet Power Switch Power Switch Overlay (Label) Strain Relief Lead-in Cord Suspension Springs Shipping Bracket Assy Heat Sink Tinnerman Fastener Motor Surge Protector Timer Voltage Control Board * K Potentiometer *55155 Triac, 35Amp - 600Volt * Items Not Shown 13
14 SPINNER HEAD ASSEMBLY Item No. Part No. Description Qty./Machine Spinner Head Complete Locknut, Reversible Spinner Cap, High Capacity Lower Spinner Head x 1/4" Hex Head Whiz Lock Screw Terminal Guard, Phenolic Bottom Washer, Phenolic Leather Floater Slip Ring 3/8" Wide Acorn Nut, Nylon Screw, #10-24 x 2 3/4" Screw, #8-32 x 5/8 PH PAN Set Screw, 1/4-20 x 2 1/2" Slip Ring Stud #10-32 Hex Nut, Brass #10 External Tooth Washer Set Screw, 1/4-20 x 3/8" Terminal Assembly 2 1,18,19,20, Floss Band Assembly W/ Element,Element Clamps, Counterweight & Nut Upper Spinner Head
15 ELECTRICAL SCHEMATIC 15
16 WARRANTY WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said GOLD MEDAL equipment or any part thereof. The term Original Purchaser as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS COMPANY, or their authorized distributor for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. GOLD MEDAL PRODUCTS COMPANY Medallion Drive Cincinnati, Ohio USA Phone: Fax:
Super Floss Instruction Manual Model #3038 and 3038EX
Part No. 88761 Revised Aug 2003 Super Floss Instruction Manual Cincinnati, OH 45241-4807 USA Safety Precautions 2 INTRODUCTION Your Floss Machine warranty is described on the back page of this manual.
More informationPart No Revised May 2002
Part No. 42231 Revised May 2002 Electronic Tornado Deluxe Whirlwind X15 Instruction Manual Model #3015A, #3015AX, #3005E, 3005XE, #3008E, #3008XE, #3007E, #3007XE, #3009E, and #3009XE Cincinnati, OH 45241-4807
More informationInstruction Manual. Whirlwind SHO
Instruction Manual Whirlwind SHO Model No. 3009 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA Part No. 63898 SAFETY PRECAUTIONS Page 2 INSTALLATION INSTRUCTIONS Inspection of Shipment After unpacking,
More informationInstruction Manual. Tornado and Deluxe Whirlwind
Instruction Manual Tornado and 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA Part No. 42231 SAFETY PRECAUTIONS Page 2 INSTALLATION INSTRUCTIONS Inspection of Shipment After unpacking, check thoroughly
More informationExport Bucket Pump Instruction Manual Models: 2114XE & 2114XD
Part No. 79064XE Revised: August 2006 Export Bucket Pump Instruction Manual Cincinnati, OH 45241 USA SAFETY PRECAUTIONS INTRODUCTION This manual provides instruction for installation and operation of the
More information!"" #$% "!&' ( ( ) *
!"" #$% "!&' (( ) * FunPop Assembly Manual Model # 2649CR Part No. 59406CR Revised: October 2004 Cincinnati, OH 45241-4807 USA INSTALLATION INSTRUCTIONS Checking Shipment Unpack carton and check thoroughly
More informationPart No DROP IN POPCORN WARMERS Instruction Manual Model #2343, 2344, 2345
Part No. 39406 DROP IN POPCORN WARMERS Instruction Manual Model #2343, 2344, 2345 SAFETY PRECAUTIONS 2 INSTALLATION INSTRUCTIONS Inspection of Shipment: Unpack all cartons and check thoroughly for any
More informationCountertop B.I.B. Butter Dispenser Instruction Manual Model #2496
Part No. 39177 Countertop B.I.B. Butter Dispenser Instruction Manual Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS Installation Instructions Countertop B.I.B. Checking Shipment Unpack all cartons and
More informationAutomatic Butter Dispenser Instruction Manual Model #2395NS
Automatic Butter Dispenser Instruction Manual Part No. 39642 Revised: July 2006 Cincinnati, OH 45241 USA Safety Precautions Automatic Butter Dispenser 2 INTRODUCTION Automatic Butter Dispenser This manual
More informationColor Wheel Instruction Manual Model #7767
Part No. 52179 Revised: April 2004 Color Wheel Instruction Manual Model #7767 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS INSTALLATION INSTRUCTIONS CHECKING SHIPMENT The Color Wheel is shipped in
More informationCincinnati, OH USA
Astro Pop Warmer Instruction Manual Model #2002 Part No. 61987 Revised July 2000 Cincinnati, OH 45241-4807 USA e-mail: goldme19@eos.net www.gmpopcorn.com SAFETY PRECAUTIONS INTRODUCTION Your new #2002
More informationInstruction Manual. Tornado and Deluxe Whirlwind
Instruction Manual Tornado and 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA Part No. 42231 SAFETY PRECAUTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel.
More informationPEANUT ROASTER Instruction Manual Model #5081
Part No. 46355 Revised: September 2004 Instruction Manual Model #5081 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS 2 MODEL # 5081 OPERATING INSTRUCTIONS Unpacking and Assembly After unpacking your,
More informationPLINKO Instruction Manual Model #7760
Part No. 52148 Revised November 2002 Instruction Manual Model #7760 Cincinnati, OH 45241-4807 USA SAFETY SHEET 2 INSTALLATION INSTRUCTIONS CHECKING SHIPMENT The is shipped in two corrugated cartons. One
More informationAccu-Meter Oil Pump. Instruction Manual. Model #2114. Cincinnati, OH USA. Part No Revised June 1996
Instruction Manual Model #2114 Part No. 79064 Revised June 1996 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS INSTALLATION CHECKING SHIPMENT Your new Accu-Meter Oil Pump is completely assembled and
More informationInstruction Manual. Auto Breeze
Instruction Manual Auto Breeze Model No. 3052-00-000 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2016 Gold Medal Products Co. Part No. 110025 SAFETY PRECAUTIONS DANGER Machine must be properly
More information!"" #$% "!&' ( ( ) *
!"" #$% "!&' (( ) * FunPop CART Assembly Manual Model # 2689 CARTS Part No. 59411 Revised: FEB 2009 Cincinnati, OH 45241-4807 USA INSTALLATION INSTRUCTIONS Checking Shipment Unpack all cartons and check
More informationROLLER GRILL Instruction Manual Model #8223, 8224, Part No Revised:March 2008
ROLLER GRILL Instruction Manual Model #8223, 8224, 8225 Part No. 88189 Revised:March 2008 Safety Precautions Models #8223, 2 #8224, #8225 FORWARD This manual covers the model # 8223, # 8223, 8225 ROLLER
More informationBag-In-A-Box Oil Pump System
Bag-In-A-Box Oil Pump System Part No. 79285 Revised February 2000 INSTRUCTION MANUAL MODEL #2257 AND MODEL #2257H Cincinnati, OH 45241-4807 USA e-mail: goldme19@eos.net www.gmpopcorn.com SAFETY PRECAUTIONS
More informationGiant Cone Display Case
Instruction Manual Model #8211 Part No. 76132 Revised June 1996 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS This equipment is designed and sold for commercial use only. This equipment is not to be
More informationSno Konette. Instruction Manual Deluxe Model #1002EX Standard Model #1003EX DC Battery Model #1009EX. Cincinnati, OH USA.
Sno Konette Instruction Manual Deluxe Model #1002EX Standard Model #1003EX DC Battery Model #1009EX Part No. 22045EX Revised June 1996 Model #1002EX Model #1003EX Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS
More informationFUNNEL CAKE FRYER Instruction Manual Models: 8078 / FC-4, 8082 / FC-6, and 8090 / FC-4
Part No. 89784 Revised: December 2005 FUNNEL CAKE FRYER Instruction Manual Models: 8078 / FC-4, 8082 / FC-6, and 8090 / FC-4 Cincinnati, OH 45241-4807 USA GAS SAFETY PRECAUTIONS INSTALLATION INSTRUCTIONS
More informationHot Dog Roller Grills Instruction Manual Model #8023, Model #8024 and Model #8025 Model #8023SL, Model #8024SL and Model #8025SL
Part No. 87630 Revised November 2007 Hot Dog Roller Grills Instruction Manual Model #8023, Model #8024 and Model #8025 Model #8023SL, Model #8024SL and Model #8025SL Model #8023 shown Cincinnati, OH 45241-4807
More informationCincinnati, OH USA
Part No. 87630PE Revised November 2007 Hot Dog Roller Grills Non-Stick Instruction Manual Model #8023PE, Model #8024PE and Model #8025PE Model #8023SLPE, Model #8024SLPE and Model #8025SLPE Model #8023PE
More informationSAM S CLUB POPPER UniMaxx Kettle Popcorn Machine Instruction Manual Model #2085CL
SAM S CLUB POPPER UniMaxx Kettle Popcorn Machine Instruction Manual Model #2085CL Part No. 49388 Revised: March 2009 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS 2 Model #2085CL UniMaxx INSTALLATION
More informationInstruction Manual. Fudge Puppy Display Case
Instruction Manual Fudge Puppy Display Case Model No. 5535 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2014 Gold Medal Products Co. Part No. 89074 SAFETY PRECAUTIONS DANGER Machine must be properly
More informationWARNING!! The attached Gold Medal Manual is for reference only and is not intended for any other purpose. The information contained in these on line manuals is subject to change at any time. Improvements
More informationGay 90 s Whiz Bang. Instruction Manual Model #2014. Cincinnati, OH USA. Part No Revised June 1996
Gay 90 s Whiz Bang Instruction Manual Model #2014 Part No. 47700 Revised June 1996 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS INSTALLATION Your new Antique Popcorn Machine is completely assembled.
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More informationDispenser & Warmer RIC-1909 RIC-1909EXP
Dispenser & Warmer RIC-1909 RIC-1909EXP Safety Precautions CAUTION This equipment is designed and sold for commercial use only. This equipment is not to be used by the consumer in home use. Do not allow
More informationModel 616 Rotating Disk Electrode Instruction Manual
Model 616 Rotating Disk Electrode Instruction Manual 219303 C / 1202 Printed in USA Advanced Measurement Technology, Inc. a/k/a Princeton Applied Research, a subsidiary of AMETEK, Inc. WARRANTY Princeton
More informationOperations & Maintenance Manual DFH-1000 DUCTLESS FUME HOOD
Operations & Maintenance Manual DFH-1000 DUCTLESS FUME HOOD ----------------------------------------------------------------We Make Clean Air----------------------------------------------------------------
More informationMODEL 7100 PORTABLE PIN WELDER OPERATOR S MANUAL
Model 7100 Portable Pin Welder MODEL 7100 PORTABLE PIN WELDER OPERATOR S MANUAL Copyright: March 22, 2005 Revised: December 20, 2016 Gripnail Corporation An Employee Owned Company 97 Dexter Road East Providence,
More informationJunior Sandblaster. Model #51 WARNING! FOR YOUR SAFETY PLEASE READ INSTRUCTIONS BEFORE OPERATING TOOL & WEAR EYE PROTECTION
Junior Sandblaster Model #51 WARNING! FOR YOUR SAFETY PLEASE READ INSTRUCTIONS BEFORE OPERATING TOOL & WEAR EYE PROTECTION PARTS LIST AND PART NUMBERS 01.Red Rubber Air Hose (5Ft) P51-01 02. Male Insert
More informationOWNER & OPERATOR INSTRUCTION MANUAL
OWNER & OPERATOR INSTRUCTION MANUAL Model No. RHW-450 FOOD WRAPPER www.turboairinc.com For service contact: German Knife Inc. 1-800-500-3519 www.turboairinc.com TABLE OF CONTENTS PAGE INSTALLATION MAINTENANCE
More informationMACHINES / RECLAIMS WITH DUST BAG
WARNING SET-UP INSTRUCTIONS MACHINES / RECLAIMS WITH DUST BAG *** READ BEFORE OPERATING EQUIPMENT *** 1. Remove plastic from machine. 2. Remove lag bolts from each of the four legs, then remove machine
More informationBlue Air. Commercial Refrigeration Inc. Installation & Operation Manual Chef Bases
Blue Air Commercial Refrigeration Inc. Installation & Operation Manual Chef Bases Please read this manual completely before installing or operating this unit! BACB53 BACB71 BACB74 BACB83 BACB86 BACB96
More informationSeries: PFUEG 1/12HP, 5000 RPM, 60 Hz Utility Pumps
INSTALLATION MANUAL Series: 1/12HP, 5000 RPM, 60 Hz ISP No: - 6/09 General Safety Information Before installation, read the following instructions carefully. Failure to follow instruction and Safety information
More informationFOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION MODEL: SERIAL NUMBER: DATE PURCHASED: PURCHASED FROM:
FOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION MODEL: SERIAL NUMBER: DATE PURCHASED: PURCHASED FROM: BASIC TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine does not work Power switch
More informationAir Curtain. Installation, Operating and Maintenance Instructions
Installation, Operating and Maintenance Instructions Save this manual for future reference. Air Curtain Model Numbers: ES026, ES036, ES042, ES048, ES060, ES072 READ THIS OWNER S MANUAL CAREFULLY BEFORE
More informationPOWER PINNER HAND WELDER 7200 OPERATOR S MANUAL
POWER PINNER HAND WELDER 7200 OPERATOR S MANUAL Copyright: January 5, 2009 Revised: November 24, 2014 Serial No. 0901189 - Gripnail Corporation An Employee Owned Company 97 Dexter Road East Providence,
More informationTissue Master. User Manual
Tissue Master User Manual This page left blank intentionally This manual is a guide for the use of the Omni International Tissue Master and accessories. Data herein has been verified and validated. It
More informationDeZURIK AFR3 Filter Regulator Used on Pneumatic Cylinder Actuators
AFR3 Filter Regulator Used on Pneumatic Cylinder Actuators Instructions D11033 August 2013 Instructions These instructions provide information about AFR3 Filter Regulators. They are for use by personnel
More informationINSTALLATION AND SERVICE MANUAL FOR TURBO-CARB HIGH CAPACITY CARBONATOR
Please refer to the Lancer web site (www.lancercorp.com) for information relating to Lancer Installation and Service Manuals, Instruction Sheets, Technical Bulletins, Service Bulletins, etc. INSTALLATION
More informationReach ins, Freeezers & Refrigerators Installation & Operation Manual
Reach ins, Freeezers & Refrigerators Installation & Operation Manual BSR23 BSF23 BSR49 BSF49 BSR72 BSF72 IMPORTANT SAFETY INSTRUCTIONS (SAVE THESE INSTRUCTIONS) Visit us on the web at www.blueairinc.com
More informationHenny Penny Hand Breader/Sifter Model HB-11
Henny Penny Hand Breader/Sifter Model HB-11 TECHNICAL MANUAL TABLE OF CONTENTS Section Page Section 1. MAINTENANCE... 1-1 1-1. Introduction....1-1 1-2. Safety... 1-1 1-3. Replacement of Belt...1-2 1-4.
More informationCW Optimizer Capacity Hat Kit. 75/80 and 80/40 Thunderbolt Vertical Antennas. for the DXE-7580-THK
CW Optimizer Capacity Hat Kit for the 75/80 and 80/40 Thunderbolt Vertical Antennas DXE-7580-THK DXE-7580-THK-INS Revision 1a DX Engineering 2012 P.O. Box 1491 Akron, OH 44309-1491 USA Phone: (800) 777-0703
More informationCardinal DETECTO. PORTABLE PLATFORM SCALES Digital Type Series 850F Owner s Manual
Cardinal DETECTO PORTABLE PLATFORM SCALES Digital Type Series 850F Owner s Manual CARDINAL SCALE MFG. CO. PO BOX 151, WEBB CITY, MO 64870 0066-M176-O1 Rev H 10/06 417-673-4631 www.cardinalscale.com Printed
More informationLBT-3 WITH 300 CFM RECLAIM MANUAL NUMBER: 506 TABLE OF CONTENTS
LITTLE BLASTER LITTLE BLASTER LBT-3 WITH 300 CFM RECLAIM MANUAL NUMBER: 506 TABLE OF CONTENTS PAGE FIGURE 1 - SET-UP INSTRUCTIONS 1 - OPERATING INSTRUCTIONS 1 - GENERAL MAINTENANCE 2 1 STANDARD CABINET
More informationMODEL G300 BRAKE BLEEDER
MODEL G300 BRAKE BLEEDER Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV120716 P/N: 81-0035H THIS PAGE INTENTIONALLY
More informationOPW Installation and Maintenance Instructions OPW Series Primary and Secondary Bucket Replacement Instructions
OPW Installation and Maintenance Instructions OPW 1-3100 Series Primary and Secondary Bucket Replacement Instructions IMPORTANT: Please read these warnings and follow the assembly instructions completely
More informationAirflo MANUFACTURING CO., INC.
Airflo MANUFACTURING CO., INC. 365 UPPER OAKWOOD AVE, ELMIRA NY 14903 PHONE: 607-733-8284 / FAX: 607-733-0587 OPERATOR & PARTS MANUAL PSV-8L ELECTRIC SPREADER Visit our website at www.air-flo.com Contents
More informationInstallation & Operation Manual Chef Base
Installation & Operation Manual Chef Base Please read this manual completely before installing or operating this unit! BACB53 BACB53M BACB71 BACB71M BACB74 BACB74M BACB83 BACB83M BACB86 BACB86M BACB96
More informationCOMPACT GLYCOL FEED SYSTEMS OPERATION & MAINTENANCE MANUAL
COMPACT GLYCOL FEED SYSTEMS OPERATION & MAINTENANCE MANUAL Model Number: Service: Serial Number: Installation Date: Installation Location / Application: PLEASE RECORD THE FOLLOWING DATA (Information is
More informationUSER S OPERATING AND INSTRUCTION MANUAL
Grand Rapids, Michigan, U.S.A. 49504-5298 USER S OPERATING AND INSTRUCTION MANUAL MODEL 797-21 BREAD SLICER 797S20000CV_21 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319 RECOMMENDED
More informationUser s Manual and Operating Instructions
User s Manual and Operating Instructions Model Numbers: CL-36-BDF-A, CL-42-BDF-A, CL-48-BDF-A E355088 READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the instructions in this manual
More informationPenguin Gentoo 600B Cordless Sprayer User s Manual
Penguin Gentoo 600B Cordless Sprayer User s Manual Please read before use. Serial Number: Date of Purchase: Distributor: LIMITED WARRANTY POLICY Masterclean Products, LLC endeavors to provide high quality
More informationAutomated I.V. Stand Cat. No OPERATOR S MANUAL. Operation& Maintenance Instructions. Raising the Standard of Care!
Automated I.V. Stand Cat. No. 741314 OPERATOR S MANUAL Operation& Maintenance Instructions Raising the Standard of Care! Table of Contents Warranty....................... 2 Hardware.......................
More informationHOTSHOT COMMERCIAL BROADCAST SPREADER MODEL OWNER S MANUAL
HOTSHOT COMMERCIAL BROADCAST SPREADER MODEL 380 OWNER S MANUAL ASSEMBLY RH. Handle Brace 1/4-20 x 2 1/4 Hex Bolt 1. Remove components from carton and place spreader upside down on a padded surface. Install
More informationSPH General Manual 400 Series
Operations & Maintenance Manual SPH General Manual 400 Series (SPH-415,416,425,426,4U6,4U5,4B5,4B6) Filename: Quatro/SPH-400 General 12/28/04 R6 ------------------------------------------------------------------------Engineering
More informationMV Series Motors Operation & Parts Manual. Models M3V, M5V, M5V-US
MV Series Motors Operation & Parts Manual Models M3V, M5V, M5V-US Introduction This manual pertains to drum pump motors MV Series. Finish Thompson, Inc. thanks you for choosing our products. We believe
More informationHP30 Slab Saw Owner s Manual and Operating Instructions
HP30 Slab Saw Owner s Manual and Operating Instructions MADE IN USA Revision 07 09.0 Manual Part No. 67 Caution: Read all safety and operating instructions before using this equipment. This manual MUST
More informationModel E600 Tarping System
10 Boulder Parkway N. Oxford, MA 01537 866-353-5826 pioneersales@wastequip.com www.pioneercoverall.com Model E600 Tarping System Installation Instructions WARNING: In order to prevent damage, the tarp
More informationViking Use/Installation Guide
Viking Use/Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site
More informationHOTSHOT HD COMMERCIAL BROADCAST SPREADER MODEL OWNER S MANUAL
HOTSHOT HD COMMERCIAL BROADCAST SPREADER MODEL 3 OWNER S MANUAL ASSEMBLY INSTRUCTIONS 1. Remove the spreader and components from carton and place hopper up-side down on a padded surface as shown. Slide
More information24 Linear Actuator 115 Volts A.C. (Cat. # C430A)
Installation, Operation & Parts Manual Read carefully the information provided. Retain manual for future reference. 24 Linear Actuator 115 Volts A.C. (Cat. # C430A) Page 1 of 8 IS10007.doc 11/15/06 IMPORTANT!
More informationFig Series. Installation and Spare Parts Manual Pilot House Control Solar-Ray Sealed Beam 7 & 8 Searchlights
Fig. 0314 Series Installation and Spare Parts Manual Pilot House Control Solar-Ray Sealed Beam 7 & 8 Searchlights 16490 N.W. 13th Avenue Miami, FL 33169-5707 www.perko.com 0314PTD5 Rev: 9/2016 Fig. 0314
More informationOIL! Use #30 SAE Motor Oil in the gear case. 1. Use the bottle of oil that is included.
2237 MARSHALLTOWN BLVD. MARSHALLTOWN, IOWA 50158 PHONE: (641) 753-5601 TOLL FREE: 1-800-383-5601 FAX: (641) 752-9748 WWW.SPREAD-ALLMFG.NET Instructions models: e-2, e-3, & e-6 grain spreaders ASSEMBLY
More informationCBR lv. Prizelawn COMMERCIAL BROADCAST SPREADER MODEL CBR IV MODEL CBR IVSS. Part# OWNER S MANUAL
Prizelawn CBR lv COMMERCIAL BROADCAST SPREADER MODEL CBR IV MODEL CBR IVSS Part# 12 OWNER S MANUAL ASSEMBLY INSTRUCTIONS 1. Remove the spreader and components from carton and place hopper up-side down
More informationPotentiometer Thrust Plate Kit (50421) Installation & Operator s Instruction Manual
Potentiometer Thrust Plate Kit (0) Installation & Operator s Instruction Manual Thank You The employees of Chore-Time Equipment would like to thank you for your recent Chore-Time purchase. If a problem
More informationCSA CERTIFIED Conforms to UL 507
Installation tion Instructions Please read and save these instructions! TURBO/MAXX12 Volt All Weather RV Ventilator Fans P/N 00-965001 Deluxe Model 1200T WITH THERMOSTAT P/N 00-965007 Standard Model 3550
More informationESE Series Cast Iron Sewage Pumps
Owner s Manual ESE Series Cast Iron Sewage Pumps TABLE OF CONTENTS General Safety.................... 2 Specifications..................... 3 Installation.................... 4 & 5 Troubleshooting...................
More informationOPERATOR S MANUAL. MODEL ORDER # MODEL HD 2.0/10 Ed HE D HD 1.8/14 Ed HE D
OPERATOR S MANUAL MODEL ORDER # MODEL HD 2.0/10 Ed 1.575-400.0 HE-201006D HD 1.8/ Ed 1.575-401.0 HE-2006D To locate your local Kärcher Commercial Pressure Washer Dealer nearest you, visit www.karchercommercial.us
More informationMOTORIZED FOLDING CAMPER WINCH
OWNER'S MANUAL MOTORIZED FOLDING CAMPER WINCH With 1200lb Lift Capacity The 12 Volt Motorized Folding Camper Winch is used to raise and lower folding campers with the touch of the switch, eliminating hand
More informationUSER S MANUAL CDL S AUTOMATIC DRAW-OFF VALVES. Les Équipements d Érablière CDL inc.
USER S MANUAL CDL S AUTOMATIC DRAW-OFF VALVES Thank you for choosing a CDL automatic draw off valve. Our 25 years of experience working with sugar makers ensures you that you acquired a performant and
More informationCONTENTS. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA USA SECTION TSM 710.1
TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES hle, ate and ale SECTION TSM 710.1 PAGE 1 of 8 ISSUE B CONTENTS Introduction....................... 1 Safety
More information4400 Airless Product Manual
4400 Airless Product Manual TABLE OF CONTENTS Precautionary Warning... Page 1 Assembly... Page 2 Operation... Page 3 Spray Tip Cleaning... Page 4 Cleaning Procedure... Page 4 Cleaning Procedure... Page
More information12 Meter Add-On Kit for the Hustler 4/5/6-BTV Vertical Antennas
12 Meter Add-On Kit for the Hustler 4/5/6-BTV Vertical Antennas DXE-AOK-12M Patent Pending DXE-AOK-12M-INS Revision 1d DXE-AOK-12M Installed on a BTV with optional Tilt Base and Direct Coax Feedpoint DX
More informationEffective June 1, 2013 This guide supersedes all previous versions
Effective June 1, 2013 This guide supersedes all previous versions 3842 Redman Drive 1-800-797-7974 Fort Collins, CO 80524 www.commandlight.com L-CAS THANK YOU Please allow us to express a simple thank
More informationBHT-1 Baler-Mounted Hay Moisture Tester
Unpacking Operators Manual BHT-1 Baler-Mounted Hay Moisture Tester 1. The BHT-1 is comprised of a display module (A) with mounting bracket and 2 knobs, a 10 ft. power cable (B) with fuse, a 25 ft. shielded
More informationPrizelawn. BF l COMMERCIAL BROADCAST SPREADER. MODEL BF l MODEL BF l SS OWNER S MANUAL
Prizelawn BF l COMMERCIAL BROADCAST SPREADER MODEL BF l MODEL BF l SS OWNER S MANUAL ASSEMBLY 3/16 Dia. x 2 COTTER PIN /32 Dia. x 1 1/4 COTTER PIN FREE WHEEL SCREEN Insert into hopper UPPER HANDLE ASSEMBLY
More informationOUTDOOR SPEAKERS OWNER S MANUAL
OUTDOOR SPEAKERS OWNER S MANUAL UNPACKING 1. Carefully unpack the speakers. If you suspect damage from transit, report it immediately to your dealer and/or delivery service. Keep the shipping carton and
More informationWash Prep Systems featuring CAT PUMPS DUPM623 DUPM820 / DUPM820-TS DUPM820D / DUPM820D-TS DUPM1010. Owner s Manual #
Wash Prep Systems featuring CAT PUMPS DUPM623 DUPM820 / DUPM820-TS DUPM820D / DUPM820D-TS DUPM1010 Serial Number: Owner s Manual #0779 072415 Installation Date: Please read and understand this manual.
More informationGETZ EQUIPMENT INNOVATORS SYSTEM DUST 120V ECONOMY PART NUMBER: 4G59542 OPERATING AND INSTRUCTION MANUAL
GETZ EQUIPMENT INNOVATORS SYSTEM DUST 120V ECONOMY PART NUMBER: 4G59542 OPERATING AND INSTRUCTION MANUAL 2320 Lakecrest Drive, Pekin IL 61554 PH. (888) 747-4389 Fax (309) 495-0625 Website: www.getzequipment.com
More informationOwner s Manual. Upper Body Unit. Serial Number Here. Date of Purchase New Hope Road, Raleigh, NC Fusion -
Revision 3 April 2015 Upper Body Unit Owner s Manual Serial Number Here Date of Purchase www.batcafitness.com 1207 New Hope Road, Raleigh, NC - 919.255.1233 Fusion - www.batcafitness.com 4 Upper Body Station
More informationA48 / A48B (base plate) BATTERY CHARGER
A48 / A48B (base plate) BATTERY CHARGER CPN41054 ISSUE DATE: 12315-8/98 ECN/DATE 106 BRADROCK DRIVE DES PLAINES, IL. 60018-1967 (847) 299-1188 FAX: (847)299-3061 15349-07-07/02 16041 6/03 14575-2/01 INSTRUCTION
More informationOWNER'S MANUAL & INSTALLATION INSTRUCTIONS 6500 Series
OWNER'S MANUAL & INSTALLATION INSTRUCTIONS 6500 Series "You push our buttons, we pour your drink!" SIDEBAR BEVERAGE SYSTEMS INC. (800)775-6150 PHOENIX, AZ Congratulations!! You are now the proud owner
More informationHOTSHOT COMMERCIAL BROADCAST SPREADER MODEL OWNER S MANUAL
HOTSHOT COMMERCIAL BROADCAST SPREADER MODEL 38170 OWNER S MANUAL ASSEMBLY 1. Remove components from carton and place spreader upside down on a padded surface. For easier assembly, remove the defector shield
More informationFD Conveyor for FD 260 Tabber
FD 260-20 Conveyor for FD 260 Tabber Operator Manual 1/2011 First Edition TABLE OF CONTENTS 1. INTRODUCTION... 1 1.1 FD 260-20 DESCRIPTION... 1 1.2 ITEMS INCLUDED... 1 1.3 OPERATING MANUAL SAFETY TERMS...
More informationDeZURIK 2 20" BOS BUTTERFLY VALVES
2 20" BOS BUTTERFLY VALVES Instruction D10459 October 2013 2-20 BOS Butterfly Valves Instructions These instructions provide information about BOS Butterfly Valves. They are for use by personnel who are
More informationSOLAR DASH CHARGING SYSTEM USER GUIDE
SOLAR DASH CHARGING SYSTEM Doc 1.01 INST049 INSTALLATION STEP 1 Place 20 watt solar panel in the dash of the vehicle facing up. Note: For ideal results position the vehicle in a manner in which the solar
More informationBottom Loading Water Dispenser
Bottom Loading Water Dispenser Model # 601000 TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE, USER MUST READ THIS MANUAL BEFORE ASSEMBLING, INSTALLING & OPERATING DISPENSER. SAVE THIS MANUAL FOR FUTURE
More informationMODEL A97 SERIES. Switchmode Utility Rectifier/Battery Charger ECN/DATE
MODEL A97 SERIES Switchmode Utility Rectifier/Battery Charger CPN108172 ISSUE DATE: 16071 7/03 ECN/DATE 106 BRADROCK DRIVE DES PLAINES, IL. 60018-1967 (847) 299-1188 FAX: (847)299-3061 Page 1 of 7 INSTRUCTION
More informationA39 UNIVERSAL SCR CHARGER
A39 UNIVERSAL SCR CHARGER ECN/DATE CPN35971 21681 01/18 16816-6/05 15349-03 05/02 14575 02/01 14268 10/00 10400 9/96 106 BRADROCK DRIVE DES PLAINES, IL. 60018-1967 (847) 299-1188 FAX: (847) 299-3061 ISSUE
More informationOperators Manual. Model 3370 Air Cooled Recirculator rev.8/98
Operators Manual Model 3370 Air Cooled Recirculator 110-080 rev.8/98 Table of contents Section 1. General Information 1.1 Warranty 1.2 Unpacking Section 2. Product Information 2.1 Description 2.2 Specification
More informationUSER S OPERATING AND INSTRUCTION MANUAL
Grand Rapids, Michigan, U.S.A. 49504-5298 USER S OPERATING AND INSTRUCTION MANUAL MODEL 777 SLICER 0777S20000-CVR THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319 THIS PAGE WAS INTENTIONALLY LEFT BLANK.
More informationAPCO CRF-100A RUBBER FLAPPER SWING CHECK VALVES
APCO CRF-100A RUBBER FLAPPER SWING CHECK VALVES Instruction D12043 June 2016 DeZURIK Instructions These instructions provide installation, operation and maintenance information for APCO CRF-100A Rubber
More informationMP/MTFL LIGHT FIXTURE (Dimming)
Robern 701 N. Wilson Ave. Bristol, PA 19007 800.877.2376 MP/MTFL LIGHT FIXTURE (Dimming) General Notes 1. It is important that the armored cable be installed during electrical rough in. 2. When surface
More informationAIR CLEANERS Model MC 3000 OWNER S MANUAL CAUTION Read complete instructions before operating. Please file for future reference.
AIR CLEANERS Model MC 3000 OWNER S MANUAL CAUTION Read complete instructions before operating. Please file for future reference. MODEL MC 3000 SPECIFICATION Input Volts: 208-230/430 VAC, 60Hz, 3 Phase
More informationHenny Penny Heated Express Cabinet Model HEC-103 Model HEC-104 Model HEC-123 Model HEC-124
Henny Penny Heated Express Cabinet Model HEC-103 Model HEC-104 Model HEC-123 Model HEC-124 TECHNICAL MANUAL LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny
More information