SAKUNDIAK --- ASSEMBLY INSTRUCTIONS OPERATOR'S MANUAL PARTS LIST HD1 0 BELT DRIVE AUGER MODEL NO. HD BD HD BD HD BD HD

Transcription

1 SAKUNDIAK --- ASSEMBLY INSTRUCTIONS OPERATOR'S MANUAL PARTS LIST HD 0 BELT DRIVE AUGER MODEL NO. HD0-400BD HD0-600BD HD0-800BD HD SAKUNDIAK EQUIPMENT L TO PASQUA ST. NORTH REGINA, SK CANADA PO BOX 996- S4P 3E PHONE : (306) FAX : (306) sakundiak.equip@sasktel.net PRINTED IN CANADA HD

2 cc.;:::::; SAKUNDIAK SECTION.00 "GENERAL" TABLE OF CONTENTS + COVER SHEET + TABLE OF CONTENTS + SIGN OFF SHEET + GENERAL SAFETY SECTION.0 "SAFETY" +MACHINE INSPECTION +DESIGNATED WORK AREA + SAFETY GUARD DESCRIPTION + TRANSPORT AND PLACEMENT + AUGER DRIVES AND LOCK OUT + AUGER DRIVES AND LOCK OUT SECTION.02 "OPERATIONS" + START UP AND BREAK-IN +LUBRICATION AND MAINTENANCE +SAFETY DECALS AND LOCATIONS +SAFETY DECALS AND LOCATIONS SECTION.03 "ASSEMBLY" + MAIN FRAME AND A-FRAME ASSEMBLY +TUBE ASSEMBLY + BELT DRIVE PTO CONVERSION SECTION.04 "PARTS" + HEAD - END ASSEMBLY + GEAR BOX ASSEMBLY + MAIN FRAME ASSEMBLY (PICTURED) + MAIN FRAME ASSEMBLY (PARTS LIST) + A-FRAME ASSEMBLY + MOTOR MOUNT ASSEMBLY + TUBE ASSEMBLY (PICTURED) + TUBE ASSEMBLY (PARTS LIST) + TUBE ASSEMBLY (PARTS LIST) Continued + P.T.O. ATIACHMENT + P.T.O. SHAFT + BRAKE WINCH ASSEMBLY SECTION.05 "INDEX" + PARTS INDEX PAGE 29 SECTION.06 "WARRANTY" + WARRANTY AND DISCLAIMER 30 HD

3 SAKUNDIAK '<:::S27 " SAKUNDIAK GRAIN AUGER SIGN OFF SHEET As a requirement of OSHA, it is necessary for the employer to train the employee in the safe operation and safety procedures with this auger. We include this sign-up sheet for your convenience and personal record keeping. DATE EMPLOYER SIGNATURE EMPLOYEE SIGNATURE HD0BD ,

4 '27, SAKUNDIAK GENERAL SAFETY Watch This Symbol. It Points Out Important Precautions. It Means "ATTENTION- Become Alert! Your Safety is Involved" Occupational safety is of prime concern to Sakundiak Equipment Ltd. This transport manual was written with the safety of the operator and others who come in contact with the equipment as our prime concern. The manual presents some of the day to day work problems encountered by the operator and other personnel. We wrote this manual to help you understand safe operating procedures for augers. We want you as a partner in the safe operation of our equipment. It is your responsibility as an owner, or operator or supervisor, to know what specific requirements, precautions and work hazards exist and to make these known to all other personnel working with the equipment or in the area, so that they too may take any necessary safety precautions that may be required. Failure to read this Transport Auger Manual and its Safety Instructions is a misuse of the equipment ' HD0BD.OJ.OO

5 cc::;:::;;. <:::::s &AKUNDIAK SECTION.0 SAFETY ALERT SYMBOLS BE ALERT This symbol is used to call your attention to instructions concerning your personal safety. Watch for this symbol- it points out important safety precautions. It means "ATTENTION! Become Alert! Your Personal Safety is Involved!" Read the message that follows and be alert to the possibility of personal injury or death. MACHINE INSPECTION. Check to see that all guards listed in the assembly instructions are in place and secured, and functional. 2. Check winch and cable for security and operation. There should be at least 3 complete wraps of cable around winch drum in full down position. Cable anchor on winch drum must be tight. 3. Are all fasteners tight? 4. Are all chains properly adjusted. (See Maintenance Section) 5. Check oil levels in gear box. (See Maintenance Section) OPERATOR QUALIFICATIONS Operator of this transport auger shall be limited to competent and experienced persons. In addition, anyone who will operate or work around a portable auger must use common sense. In order to be qualified, they must know and meet all other requirements, such as:. Some regulations specify that no one under the age of 6 may operate power machinery. This includes augers and flight type elevators. It is your responsibility to know what these regulations are in your area or situation. 2. Current OSHA regulations state in part: "At the time of initial assignment and at least annually thereafter, the employer will instruct every employee in the safe operation and servicing of all equipment with which the employee is, or will be involved." 3. Unqualified persons are to stay out of the work areas. 4. A person who has not read and understood all the operating and safety instructions is not qualified to operate the machine HD0BD.04.00

6 cz::;;;:::; SAKUNDIAK <::::S27 DESIGNATED WORK AREA The following diagrams will show the designated work areas. These areas shall be marked off with colored nylon or plastic rope hung by portable barriers to define the designated work areas. Under no circumstances should persons not involved in the operation be allowed to trespass into the work area. It shall be the duty of all operators to see that children and/or other persons stay out of the work area! Trespass into the area by anyone not involved in the actual operation, or trespass into a hazard area by anyone, shall result in an immediate shut down by the operator. Prior to start up and during operation, it shall be the responsibility of the operators to see that the work area has secure footing, is clean and free from all debris, and tools which might cause accidental tripping and/or falling. P.T.O. BELT DRIVE CAUTION! _A, WALKING SURFACE,.. IS IT SLIPPERY? ARE THERE THINGS TO TRIP YOU? A KEEP AWAY! OVERHEAD WIRES A HAZARD, KEEP OUT, AUGER INTAKE AREA. HAZARD, KEEP OUT! A UNDER AUGER AND UNDERCARRIAGE AREA_ I I I I I I I L A HAZARD, KEEP OUT, AUGER DRIVE AREA. P.T.O. DRIVE AREA. WORK AREA AUTHORIZED PERSONNEL ONLY. WHEEL CHOCKS.'----+_/ WHEEL CHOCKS. " " \ /./ \ I I I I I SUPPORT DISCHARGE END. HD '

7 cz:;::;:, K SAFETY GUARD DESCRIPTION HEAD-END INTAKE FORK GEAR BOX PULLEY GUARD GEAR BOX SHAFT GUARD ENGINE PULLEY GUARD P.T.O. ATTACHMENT GUARD TUBULAR DRIVE SHAFT GUARD HD0BD

8 <::::::s &AKUNDIAK TRANSPORTANDPLACEMENT Moving the Auger with the Towing Vehicle to or from the Work Area. Placement: Moving the Auger with the Towing Vehicle into or out of its Working Position.. Always transport your auger in the full down position. The A-Frame of the undercarriage should be seated against the down position stop. 2. Make sure that the hitch pin is securely attached and an alternate safety chain is secure to the auger and towing vehicle. 3. Be alert of overhead obstructions and electrical wires. Electrocution can occur with out direct contact. Failure to do so will result in severe injury or death. 4. Never allow persons to stand underneath or ride on the auger when it is being transported. Always move an auger with a vehicle, never manually. Test the intake for downward weight before removing from hitch. Lift slowly, no higher then hitch bar. Be sure grain is out of tube and auger is on level surface. Do not place lumber under wheels for increased weight. Before raising, check for power lines. When auger is in place, anchor intake end and/or discharge end and chock wheels. When in transport or placement PTO shaft to be disconnected. OVERHEAD WIRES KEEP AWAY! A KEEP AWAY!.. OVERHEAD WIRES II ' HD0BD.07.00

9 SAKUNDIAK AUGER DRIVES AND LOCK OUT It is essential to inspect your drive before adding power and know how to shut down in an emergency. Whenever servicing or adjusting your equipment, make sure you stop your engine and lock out your power source! A. GASOLINE DRIVES Power Source PTO- Shaft B.PTO. Never attempt to adjust or service engine while it is in operation. 2. Shut down and allow engine to cool before filling with fuel. 3. Keep all guards and shields in place. Lock Out. For engines with rope or crank start - remove spark plug wire or spark plug. 2. For engines with electric start- remove ignition key, spark plug wire or spark plug.. Never use a PTO shaft without a rotating shield in good working order. Also see that the power drive system safety shields are in place at the auger gear box and the power source. 2. Be certain that the PTO shaft is securely attached to the gear box and the power source. 3. Before starting power source, be certain power to PTO is off. 4. Stay out of the hazard area of an operating PTO. Lock Out. Remove ignition key or coil wire from power source. If this is impossible, remove the PTO shaft from the work area. HD0BD.08.00

10 cz.>:::::, &AKUNDIAK AUGER DRIVES AND LOCK OUT Power Source C. ELECTRIC. Electric motors and controls shall be installed by a qualified electrician and must meet the standards set by the National Standards Electrical Code. 2. A magnetic starter should be used to protect your motor. 3. You must have a manual reset button. 4. You must disconnect power before resetting your motor. 5. Reset and motor controls must be located so the operator has full view of the entire operation. 6. Keep all guards and shields in place. Lock Out A main power disconnect switch capable of being locked only in the Off position shall be provided. This shall be locked whenever work is being done on the auger.

11 SAKUNDIAK SECTION.02- OPERATIONS START-UP AND BREAK-IN Sakundiak Equipment Ltd. recommends that before you start augering grain with your new auger that you should do the following:. Run the grain auger at approximately /2 the normal operating speed (270 rpms with PTO) without adding grain to the intake for approximately five minutes. 2. Bring auger up to full operation speed (540 rpms with PTO) and slowly add grain to intake of auger. 3. Continue to add grain slowly until approximately 000 bushels (28 tonnes) has been run through the grain auger. This will "shine up" the flighting and the tube. 4. The operator should be aware if any unusual vibrations or noises, determine source, shut off, LOCK OUT power source and adjust. OLD AUGER START-UP AND BREAK-IN Sakundiak Equipment Ltd. recommends that before augering grain with your used auger, you should do the following:. Before positioning the auger, be sure all guards and shields are in place, securely fastened and fully operational. 2. Check and fill if necessary, all lubricating fluids, and grease all fittings. CAUTION. Observe work area restrictions (see work area diagram.) 2. Keep all safety guards and shields in place. 3. Make certain everyone is clear before operating or moving the machine. EMERGENCY SHUT -DOWN. Should the auger be immediately shut down under load --- disconnect and lock out the power source. Clear as much grain from the hopper and auger as you can. Never attempt to start the auger full. 2. Starting the auger under load may result in damage to the auger. Such damage is considered abuse of the equipment. 3. Reconnect power source and clear grain gradually. NORMAL SHUT-DOWN. Make sure that the hopper and auger are empty before stopping the unit. 2. Before the operator leaves the work area, the power source shall be locked out. CLEAN-UP AND STORAGE When the operation is completed, it is recommended that you move the auger to the new work area or to a storage area.. Clean entire work area. 2. Remove anchors, supports and chocks. 3. Move auger slowly out of working position with towing vehicle --- not by hand. (see transport and placement) 4. When augering out of bin is complete, do not attempt to pull on axle with tractor to remove from bin. This will bend the auger. 5. If not in transport position, lower auger to the full down position immediately upon clearance of any obstruction. 6. Transport to new work area or storage area. We recommend that the auger be stored in the full down position with intake end anchored. 4. Keep hands, feet, and clothing away from all moving parts. 5. Lock out power sources to adjust, service or clean. 7. Do not attempt to pull grain auger out of snow bank in winter. This will cause damage to the tube assembly. 8. Make certain that there is no snow build up on auger tube or frame, which will bend the auger frame or auger tube HD08D '

12 SAKUNDIAK AUGER LUBRICATION AND MAINTENANCE DANGER Do not service or lubricate while the auger is running. LOCK OUT the power source. GEAR BOX. 0 inch grain augers, fill with 2 quarts (2 litres) of #90 gear oil. 2. Do not over fill gear box. 3. Change oil once a year or every 20,000 bushels (550 tonnes) or when it gets contaminated with water. DRIVE SHAFT BEARINGS. Grease once a day with good quality grease. HEAD-END. The bearings are pre-lubricated and do not require further lubrication. 2. The sprockets and chain should be oiled with #30 gear oil once every season. 3. Keep chains snug, do not over tighten. FORK BEARING. Grease every,000 or 2,000 bushels (28 or 54 tonnes) with a good quality grease. WHEEL BEARINGS. The wheel bearings are packed at the factory. 2. They should be cleaned and repacked once a year. PTO SHAFT AND ATTACHMENT. PTO shaft and attachment should be greased once a day with a good quality grease ' HD0BD..00

13 _.... SAKUNDIAK...._ ;;;::::s::? CAUTION. Do not operate this auger before reading and understanding the operator's manual. 2. Do not operate this auger unless all guards and safety devices are securely in place. 3. Do not adjust, service, lubricate, clean, unclog or move this unit until all power has been shut off. 4. Make certain everyone is clear of the equipment before moving or operating. Never allow children, vstors or untrained personnel in the area. 5. Keep hands, feet and clothing clear of all moving parts while in operation. 6. Support discharge end or anchor intake end to prevent upending. 7. Empty auger and lower to transport position before moving to prevent upending. To Prevent Serious Injury or Death Avoid unsafe operation or maintenance. Do not operate or work on this machine without reading and understanding the operator's manual. If manual is lost, contact your nearest dealer for a new manual. 8. Lower this unit to transport position when not in use. 9. When raising or lowering auger watch for overhead powerlines and other obstructions. 0. Disengage belt tension release on motor base before starting motor.. Disconnect power on electric motor driven units before resetting motor overload make certain electric motors are properly gronded. 2. Always make certain that trained personnel are in attendance while unit is in operation. 653 A DANGER Upending Hazard The intake end of the grain auger must always have downward weight. Always test it before releasing it from the vehicle or holddown. Lift the intake slowly and keep it no higher than the tractor tow bar when attaching or releasing it. Immediately lower the auger to transport position before moving. Failure t? do so will cause upending, Which Will result in serious injury or death. 655 A DANGER A DANGER ROTATING FLIGHTING Keep away from intake end. Failure to do so will result in serious injury or death. Do not use this auger without intake guard in place. 65 ELECTROCUTION HAZARD To prevent serious injury or death from electrocution: Stay away from overhead powerlines when transporting or raising augers. This machine is not grounded. Electrocution can occur without direct contact H:D

14 Cf3:::> _._._.... SAKUNDIAK MOVING PART HAZARD To prevent serious injury or death from moving parts: Close and secure guards and shields before starting. Keep hand, feet, hair and clothing away from moving parts. Disconnect and lockout power source before adjusting or servicing. Do not stand or climb on machine when operating. A CAUTION. After lowering the auger, always tum the winch handle clockwise at least two clicks to tighten the brake lock. 2. Maintain control of the handle at all times. 3. Maintain light cable tension when in the towing position. 4. Do not put lubricatjon of any kind on the brake disc. 5. Check cable before each use. Replace if frayed or damaged. 659 A DANGER ROTATING DRIVELINE CONTACT CAN CAUSE DEATH KEEPAWAY! Do not operate without - All driveline, tractor and equipment shields in place. Drivelines securely attached at both ends. Driveline shields that tum freely on driveline. SW ' HD

15 sk '27 SECTION.03 -ASSEMBLY NOTE: Reference to right and left hand used throughout this manual refers to the position standing at the intake end looking toward the head-end. MAIN FRAME ASSEMBLY. 2. A-FRAME ASSEMBLY Lay out frame as shown in figure (No.0) Install spindles in frame using the last or bottom holes in the A-Frame.. Lay frame out as shown in figure (No.0) 2. Fasten Main Frame to axle using 7/6" dia. bolts. (do not tighten) 3. Install Main Frame to axle braces and main frame cross brace at the same time. 4. Install winch base plate and belt idler bracket. 5. Bolt on winch. 6. Fasten battery mount. 7. Assemble cable roller bracket and mount frame. 8. Leave out two bolts on winch plate so Main Frame can be spread apart to fit on tube pins. 3. Place A-Frame so the stub on the Main Frame axle can be slid into the second hole on the A-Frame. Now do the same on the other side. Both pieces should be installed on the axle and be pointing in the opposite direction. (Fig. No.0) 4. Install A-Frame cross brace on A-Frame. 5. Mount gooseneck to the A-Frame, using the middle holes on the gooseneck and the upper end of A Frame. 6. Install track roller brackets and track roller as shown in figure (No.02). (Do not tighten) 7. When assembling swing augers, install lift cable roller at the upper end of gooseneck. 8. Mount tires on rims and mount rims on axle spindles. FIGURE 02 FIGURE HD0BD.4.00

16 cc;;:::;:., &AKUNDIAK TUBE ASSEMBLY. Tube assembly has been pre-assembled at the. factory, at this time you should check the tube for damage. TUBE ASSEMBLY INSTALLATION Raise head-end of the auger tube about 5ft. Position the complete frame under the auger tube. Place A-Frame to head-end, and Main Frame to intake end. At this time you should run the cable around the grooved roller on the gooseneck. 2. After checking for damage, this is a good time to grease drive shaft bearings and oil head-end chains. Head-end bearings have been prelubricated. 2. Lift A-Frame up to head-end of the track on the bottom of the auger tube. Spread track roller brackets and fit over track, then tighten. 3. Make sure that the track rollers are well lubricated and rotate freely. 4. Now raise the head-end of the auger tube high enough to allow the Main Frame to fit on the steel pins of the tube assembly. These are the same pins that the truss cable eyebolts are mounted to. 5. Roll frame back to allow the frame to line up to the tube assembly. Then tighten all the bolts on the complete frame and insert all other frame bolts. 6. Lower the auger to the ground and allow the A Frame to rest against the track stop. 7. Attach cable to the bottom track stop with cable clamp. Cable will already be threaded through the cable roller in the gooseneck (done in previous step). The cable then runs around the Main Frame cable roller and then to the winch. Allow 3 wraps of cable around the winch drum before cable is tight. 8. A regular 0" belt drive auger is complete except for safety guards (engine pulley guard and base plate, gear box pulley guard). Also make sure all other guards and shields are in place and secure for your safety. A-Frame/Gooseneck Cable Clamp FIGURE 03 Track Stop ' HD0BD.5.00

17 SAKUNDIAK BELT DRIVE PTO CONVERSION. Mount PTO base onto motor mount base. (leave bolts loose) 2. Bolt quard mounting brackets to PTO base on the side that has bolt holes. The small ends of the bracket bolts onto the PTO base. 3. Bolt the quard base to the large end of the brackets. 4. Take the V-pulley in the PTO kit and mount it on the gear box of the main auger tube. Hub of the V-pulley must face into gear box. 5. Take the old V-pulley from the gear box and mount it on the PTO shaft of the PTO base. Face the hub of the V-pulley into the PTO base. 6. Bolt guard cover onto guard base. 7. Slide splined coupler onto PTO drive shaft and then tighten the screws. 8. Bolt cover guard to V-pulley guard. P.T.O. Attachment Pulley Guard Mounting Brackets Guard Back Hinge Guard Cover FIGURE 04 Spline Guard ' HD

18 SAKUNDIAK HEAD-END Bearing insert is available in set screw or locking collar. See REF NO. 4-7 below. Also available is the set screw bearing c/w casting. See REF NO. 2 & 3 below. REF NO. HD0 DESCRIPTION Head-end base plate /2" Locking collar bearing c/w casting /2" Bore 6 tooth sprocket /2" Bore 28 tooth sprocket /4" x 7/8" Woodruff key No c/w connecting link Head-end cover /4" x /2" Self-tapping screws 5/8" x /2" UNC Bolts 5/8" Whiz Nut /2" Locking collar bearing c/w casting /2" Set screw bearing c/w casting (Optional for REF NO.2) /2" Set screw bearing c/w casting (Optional for REF NO. ) /2" Locking collar bearing insert for REF NO. 2 /2" Locking collar bearing insert for REF NO. /2" Set screw bearing insert for REF NO. 2 /2" Set screw bearing insert for REF NO ' H0 0BD.7.00

19 GEARBOX DESCRIPTION 626 Gear box housing Double bearing cover Single bearing cover Bevel gear Tapered roller bearing Tapered roller bearing Tapered bearing cup Snap ring 9 2 /2" UNC bolt 0 2 /2" Lock washer 634 3/8" Stakenut /2" Stakenut Input shaft Output shaft Woodruff key /8" I.D. Oil seal /4" I.D. Oil seal /8" NPT Oil level plug /8" NPT Oil drain plug Vent and plug bushing Gasket Shim 23 3 Square key 540 Gear box complete ' HD0BD.8.00

20 s: - )> )> 3: m Note: Ref No.'s 3, and 2 thru 25 are standard for 600, Series HD0 augers, and are optional for 400 Series HD0 augers. J: c c CJ m r ---4 c - < ;a m... (.CJ

21 , """ &AKUNDIAK MAIN FRAME HD 0 BELT DRIVE REF NO. HD0 NO. USED DESCRIPTION Main frame Main frame Main frame Main frame /8" x 2 /2" UNF bolt c/w nut and lock washer 3 38 Cable roller bushing 4-4 3/8" x " UNC bolt c/w whiz nut Winch base plate 6 68 Brake winch Main frame to axle brace Main frame to axle brace Main frame to axle brace Main frame to axle brace /8" x 9" UNC bolt c/w nut and lock washer Battery top mount bracket Axle Axle Axle Axle /2" x 4 /2" UNC bolt c/w nut and lock washer 2-2 3/4" x /4" Bolt with grease fitting c/w lock washer and 3/4" flat washer 3-7 7/6" x 3 /2" UNC bolt c/w nut and lock washer Battery mount Main frame cross brace 6-4 7/6" x 4" UNC bolt c/w nut and lock washer 7 07 Cable roller Cable roller bracket 9-2 5/8" x " UNC bolt c/w lock washer /2" Plated flat washer Belt idler channel bracket Idler bushing Idler roller Belt idler brace /8" x 3/4" Carriage bolt c/w nut and lock washer Belt idler kit \. H00BD

22 SAKUNDIAK A- FRAME 2 8 HD0 BELT DRIVE REF NO. HD0 DESCRIPTION " Wheel A-frame A-frame A-frame A-frame Grease seal Tapered roller bearing cone (inner) Tapered roller bearing cup (inner) Hub Tapered roller bearing cone (outer) Tapered roller bearing cup (outer) Dust cap 0 43 Gooseneck 64 3 Trolley bushing Track roller 3 65 Track roller spacer 4 07 Cable roller Trolley quide /2" x 3" Spindle Complete hub clw spindle and bearings 8 2 /8" x 3/4" Cotter pin 9 2 5/32" x /4" Cotter pin /8" X 2 3/8" Pin /2" x 7/8" Wheel stud /8" x 5" UNC Bolt c/w nut and lock washer /4 Castlated nut A-frame cross brace- 600, 800, /8" x 4 /2" UNC bolt c!w nut and lock washer- 600, 800, P.T.O. Bracket U-Bolt P.T.O. Bracket Base plate P.T.O. Bracket Holder P.T.O. Bracket Pin and clip P.T.O. Bracket Kit. Includes items No. 26, 27, 28, and 29 2 HD0BD.2.00

23 GAKUNDIAK MOTOR MOUNT ASSEMBLY HD0 BELT DRIVE REF NO. HD0 DESCRIPTION 587 Motor mount base Leveling bar bracket - lower Motor mount pivot bracket Motor mount bracket Pivot bushing 6 07 Leveling bar adjusting screw- lower- LH Leveling bar Leveling bar Leveling bar Leveling bar Leveling bar adjusting screw- upper- R.H Leveling bar bracket- upper 0 2 /4" x /2" Whiz bolt dw whiz nut 4 3/8" x " Carriage bolt c/w nut and lock washer 2 4 3/8" x /2" UNC bolt c/w nut and lock washer 3 2 3/8" x 2 3/4" UNC bolt c/w nut and lock washer 4 4 7/6" x " UNC bolt c/w nut and lock washer 5 2 7/6" x 3" UNC bolt c/w nut and lock washer 6 4 /2" x /4" UNC bolt c/w nut and lock washer 7 3 3/4" Jam nut- R.H Engine pulley guard base Engine pulley guard Extension handle H0 0B

24 ':! 0 0 "' tl ' c: OJ m )> en en m s: OJ : c 0 OJ m I - c :;o < m l:

25 SAKUNDIAK TUBE ASSEMBLY HD0 BELT DRIVE "''I REF NO. HD0 NO. USED II DESCRIPTION 526 Tube assembly Tube assembly Tube assembly Tube assembly f'"light assembly Flight assembly Flight assembly Flight assembly Intake fork- complete, includes Ref No.'s 4, 5, 6, 7, 8, 37, 38, Intake fork c/w bushing, includes Ref No.'s 4, Intake fork bushing Intake guard Auger hitch Hitch pin and clip Gear box 542 Coupler chain Coupler sprocket Pillow block bearing Pillow block bearing Pillow block bearing Pillow block bearing Drive shaft- top section -400, 600, 800, Drive shaft- bottom section Drive shaft- bottom section Drive shaft- bottom section Drive shaft- bottom section Triple groove V-pulley c/w hub Triple groove V-pulley only Pulley hub only Gear box shaft guard Lift cable Lift cable Lift cable Lift cable Pulley guard - front Pulley guard - back Pulley bracket- upper Pulley bracket - lower B-270 V-belt B-30 V-belt B-355 V-belt B-405 V-belt Drive shaft guard- top section Drive shaft guard- top section Drive shaft guard- top section Drive shaft guard -top section Drive shaft guard- middle section- 400, 600, 800, Drive shaft guard - bottom section Drive shaft guard- bottom section Drive shaft guard - bottom section Drive shaft guard - bottom section Drive shaft guard nylon bushing Drive shaft guard nylon bushing Drive shaft guard nylon bushing Drive shaft guard nylon bushing /4" x 5/8" UNC Whiz bolt c/w whiz nut 3 3 3/8" x /4" Woodruff key 32-4 /2" x 3/4" UNC Whiz bolt Ball bearing insert Ball bearing housing Drive shaft bearing guard /4" Cable clamp /8" x " Carriage bolt HD0BD

26 , SAKUNDIAK TUBE ASSEMBLY HD0 BELT DRIVE """' REF NO. HD0 NO. USED II DESCRIPTION /8" x " Carriage bolt /8" x " Carriage bolt /8" x " Carriage bolt /8" Whiz nut /8" Whiz nut /8" Whiz nut /8" Whiz nut /8" x " UNC Whiz bolt Truss cable Truss cable Truss cable Truss riser- 600, 800, Truss riser brace- 600, 800, Truss tension bracket- 600, 800, /2" UNC nut 45-2 /2" x 6" UNC eyebolt /6" Cable clamp - 600, 800, /4" x 5/8" Carriage bolt 48-4 /4" UNC Whiz nut 49 - /4 Wing nut /6" x " UNC Bolt cjw nut - 600, 800, /8" x 3/4 Carriage bolt /8" x 3/4" Carriage bolt- 600, 800, Pulley hub bolt Decal "SAKUNDIAK" Decal "HD0-400" Decal "HD0-600" Decal "HD0-800" Decal "HD0-2000" Auger flight 2" I. D. (per foot) Cupped flight 2" I. D. (per 2 feet) Auger tube 0" O.D. (per foot) Drive shaft tube -5/8" O.D. (per foot) Flight shaft tube 2" O.D. (per foot) Sakundiak red paint Sakundiak grey paint Sakundiak red spray bomb paint Sakundiak grey spray bomb paint "-2 5 HD0BD I

27 &AKUNDIAK P.T.O. ATTACHMENT BELT DRIVE Note: 6" Pulley supplied with P.T.O. attachement, is to be assembled on the gear box. /2" Pulley supplied with auger is assembled on the P.T.O. REF NO. HD0 DESCRIPTION PTO attachment base Bearing and casting complete Bearing - insert only Drive shaft Triple groove V-pulley complete with hub /2" x 3/4" UNC Bolt, nut, lockwasher Drive shaft guard PTO splined stub Mounting bracket- guard PTO guard - back PTO guard - front PTO spline guard Mounting bracket- guard 5/6" UNC Nut, lock washer 5/6" x " Carriage bolt /4" x /2" UNC whiz bolt, nut /4" x " Woodruff key ' HD0BD.26.00

28 cc:;::::;;, SAKUND PTO SHAFT WEASLER 90" REF NO. HD0 DESCRIPTION 2004 Quick disconnect yoke Yoke repair kit Yoke and male shaft Outer PTO shield Cross and bearing kit Yoke and female tube Nylon bearing Shield centralizer Inner PTO shield Yoke repair kit- shear end Snap ring Quick disconnect shear yoke Safety decal Safety decal 5 /4" x " Roll pin /6" x 5/8" UNC Gr.2 bolt /6" Nut 2036 Complete PTO shaft (#40-90) ' HD0BD.27.00

29 &AKUNDIAK FULTON K2550 BRAKE WINCH BELT DRIVE REF NO. HD0 DESCRIPTION 672 Cable clamp 2 7 Handle 3 72 Pawl & spring Shaft brake disc Spacer Bushing Bushing Spring pin Output shaft Ratchet gear 947 Pinion & disc Friction disc Input shaft 4 Drum bolt 5 Drum lock nut 6 Drum spacer 7 Drum assembly 8 Frame lock nut 9 2 Frame spacer 20 Frame bolt 2 Frame 22 Washer (input) 23 Washer (output) 24 2 Handle lock nut 25 Woodruff key 26 Gear 27 E-clip HD

30 Part ' ' Ref Page Part Ref Index Page HD0BD Part Ref Page

31 SAKUNDIAK Limited Warranty Statement Sakundiak Equipment Ltd. warrants each new Sakundiak Equipment Ltd. product to be free from defects in material and workmanship. This warranty is applicable only for the nonnal service life expectancy of the product or components, not to exceed twelve (2) consecutive months, or forty-five ( 45) days in the case of commercial use, from the date of delivery of the new Sakundiak Equipment Ltd. product to the original purchaser. Genuine Sakundiak Equipment Ltd. replacement parts and components will be warranted for thirty (30) days from date of purchase, or the remainder of the original equipment warranty period, whichever is longer. Under no circumstances will Sakundiak Equipment Ltd. cover any merchandise or components thereof, which, in the opinion of Sakundiak Equipment Ltd., has been subjected to misuse, unauthorized modifications, alteration, an accident or if repairs have been made with parts other than those obtainable through Sakundiak Equipment Ltd. Sakundiak Equipment Ltd. in no way warrants engines, batteries, tires or other trade accessories since these items are warranted separately by their respective manufacturer. Our obligation under this warranty shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in our judgment, shall show evidence of such defect, provided further that such part shall be returned within thirty (30) days from date of failure to Sakundiak Equipment Ltd., routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. This warranty shall not be interpreted to render Sakundiak Equipment Ltd. liable for injury or damages of any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other reason. Except as set forth above, Sakundiak Equipment Ltd. shau have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages. Sakundiak Equipment Ltd. makes no other warranty, expressed or implied, and, specifically, Sakundiak Equipment Ltd. disclaims any implied warranty or merchantability or fitness for a particular purpose. Some states or provinces do not permit limitations or exclusions of implied warranties or incidental or consequential damages, so the limitations or exclusion in this warranty may not apply. This warranty is subject to any existing conditions of supply which may directly affect our ability to obtain materials or manufacture replacement parts. Sakundiak Equipment Ltd. reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion, limitations and reservations HD 0BD.30.0