Blue Lightning Belt Drive Installation Instructions

Size: px
Start display at page:

Download "Blue Lightning Belt Drive Installation Instructions"

Transcription

1 June 25, 2007 Water Walker LLC Montrose Colorado Blue Lightning Belt Drive Installation Instructions Parts List: Bolts and mounting hardware A special installation tool A Gates (brand) Poly Chain GT 2 synchronous belt An aluminum CNC machined Head Frame A machined from 4043 steel axle/plate An aluminum Driver Sprocket with two belt retention rings An aluminum Driven Sprocket assembly with installed propeller lugs One (installed) front oil seal One paper gasket to attach propeller mount half hub One (installed in the Driven Sprocket) front tapered roller bearing One rear tapered roller bearing One Bear Nut retaining clip and thrust washer assembly Four stand off Studs to hold cover plate One cover protection plate Two aluminum block braces to attach to each engine head. (ZZ type GM engine only) The Blue lightning Belt Reduction unit is designed for GM performance crate engines for air boats and has been developed over the past five years. They have been field tested on several boats for hundreds of total hours. You have a Propeller Speed Reduction Unit (PSRU) that provides all of the benefits of older belt drive units, of gear box reduction units and more. The total weight of the Blue Lightning Drive Unit including mounting hardware is 59 pounds, making it the lightest weight PSRU commercially available to date for airboats. The Blue Lightning drive unit is currently manufactured and offered for GM Crate engines of the current models produced after 1986?, including the newer GM LS series of aluminum block crate engines. For instance, an installation has successfully been completed and run by GTO Airboats, Inc. on a Water Thunder performance LS engine. Currently the engine of choice would be the GM ZZ383, 425 HP engine. The unit is bolted onto the rear of the engine block using the 3/8 bolt holes that would normally receive an automotive transmission in a car. In addition, there are two more attach points from the unit to the engine that attach one to each head of the engine for a total of nine attach points. These nine attach points are needed to withstand the huge gyroscopic forces incurred when an air boat turns rapidly as in during a spin 360 turn. Water Walker, LLC Page 1 8/17/2007

2 See the enclosed picture of standard hardware including the two aluminum blocks that mount, one to each of the engine heads of the ZZ line of GM engines. These are for additional support of the unit to the engine. Note that the ZZ line of GM engines require standard SAE threads and that LS GM engines generally require metric thread bolts to attach the various parts of the unit to the LS engine. There are other differences between the units made for LS engines and is why you were asked to specify which unit style wanted when ordering your unit. should then be installed onto the engine mount stand either on the shop floor or in the boat. The axle shaft and plate piece is the heart of the unit and is machined from 4043 forged steel. Begin its installation by first observing that there are two 3/8 holes at the top of the head plate that are for temporary assistance in the installation of the axle shaft/plate. There are extra 3/8 bolts, nuts, washers and 3/8 nylon washers in the hardware group. Begin the installation by bolting these two aluminum support blocks to each of the engine heads. Then mount the unit head plate to the rear of the engine block using the 3/8 bolts provided. Use Blue Locktite on these bolt threads and torque to 35 ft. lbs. At each lower side of the head plate there are two ½ threaded holes provided for the attachment of the engine stand rear engine mounts. These engine mounts are not provided and must be fabricated by the airboat builder as part of the engine stand assembly. Be sure to use ½ bolts, grade 8, into the aluminum of enough length to use all of the depth and threads available without the bolts extending into the cavity for the starter ring of the engine. Torque these bolts to 50 ft. lbs. and use Blue Locktite. The engine with the head plate attached Water Walker, LLC Place the axle/plate into its recessed cavity in the head plate and notice that there is a grove for the retainer lock washer at the end of the axle shaft. Position this grove at the top (up) as it positions the axle centerline at its lowest position of the cam movement for later tightening the main belt. Use two 3/8 bolts with first metal washers and then the nylon washers through these two holes placing a washer and nut at the rear of the head plate to hold the axle/pale in place during future rotation to finally tighten the Gates Poly Chain G2 belt as the installation proceeds later. You will see that these two nylon washers cover the edge of the axle/plate to hold it in place during rotation and belt tightening. These two bolts, washers and nuts will be Page 2 8/17/2007

3 removed after final installation and be stored for future use if the unit is to ever be disassembled. The top large driven sprocket is to be installed next. Notice the bearing races are already pressed into the wheel and that the rear tapered roller main bearing and the large oil seal are already installed into the rear of the sprocket wheel. Apply some light oil into the rear roller bearing and onto the axle including the seal area so that the seal lips will easily slip onto the seal area. Carefully slide and rotate the sprocket onto the axle with the seal sliding onto its area while the roller bearing also slides onto its area of the axle. Lightly oil and then place the smaller rear roller bearing onto the axle and into the sprocket. Add the thrust washer, locking clip and the Bear nut to hold it all in place. Tighten the Bear nut to approximately 30 ft. lbs. of torque and set the lock features of the clip and Bear nut. (You could temporarily place a couple of 3/8 bolts into matching holes of the axle/plate and head plate to hold it from rotating while applying torque to the Bear nut, then remove them again.) the flex plate and onto the crankshaft. Place the included guide pin through the flex plate into the crankshaft hole. With the flex plate still in place, hang the belt over the top sprocket and under the smaller drive sprocket and then position this sprocket onto the crankshaft being sure to align the sprocket with the crankshaft guide pin. (It is helpful to have another person press the two sides of the belt together with two short straight edges to mount the driver sprocket on the crankshaft.) Start the 7/16 X 3 grade 8 bolts with Nord lock washers (LS engines require 11 millimeter bolts) through the sprocket and through the flex plate and tightening them drawing the sprocket into place with the belt loosely in place. Use Blue Loctite and torque to 50 lb. lbs. Install the belt retention ring onto the rear of the drive sprocket using the screws provided. Use Blue Locktite on these as well and tighten to modest torque. The beveled edge goes to the outside as it is on the front edge ring and not against the belt. The smaller drive sprocket and belt are next to install. Remove the factory 7/16 bolts that hold the starter ring flex plate to the crankshaft of the engine. These bolts will be replaced with longer ones that secure this sprocket over A special tool is provided to tighten the belt by rotating the axle/plate in its head plate recess. The axle is offset approximately from the center of the plate part of the axle/plate and rotation within the recess raises the axle centerline of the assembly to increase the center to center distance of the sprockets to tighten the belt. The axle/plate Water Walker, LLC Page 3 8/17/2007

4 assembly should be rotated clockwise as viewed from the back of the boat. to tighten the belt. The belt is tight when the belt can be deflected inward along one of its sides 1/8 with an approximate 50 pound force on the belt. washer for vibration and thermal expansion between the closer mount plate and the support block and the small round spacer on the other one and tighten 3/8 bolts and nuts to 35 ft. lbs. Remove the temporary bolts and nylon washers at the top of the axle/plate as described earlier. Place the four cover stand off studs into the head plate. Use Blue Loctite and modest torque with pump pliers or a small pipe wrench to tighten. Place the protective cover over these studs with the ¼ screws provided. Do not use Loctite on these screws so as to be able to remove them easily for routine service inspections later. Insert the special tool from the right side behind the top sprocket so that the two metal pegs can be inserted into two of the lower 3/8 holes of the axle/plate. Press the tool downward and turn the axle/plate clockwise in its recess. Repeat with a new tool position as needed until the above belt force and deflection is achieved. (The earlier described temporary bolts, washers and nylon slide washers need to be snug so as to hold the axle/plate securely into the recess of the head plate to assure that when the permanent bolts are drawn tight that no additional belt tension is developed.)then rotate the axle/plate as much more or less as may be needed to align twelve of the twenty four holes with the twelve head plate holes. Install the mount half of the propeller hub using the gasket provided, the Nord Lock washers and torque the ½ bolts to 50 ft. lbs. Refer to propeller installation instructions for the completion of the Propeller installation. Notice that some of the holes in the head plate are blind. (You can not put a nut behind them) They have self locking heli coil inserts installed to receive 3/8 bolts. These bolts will be shorter and you are to match the sizes as may be required from the hardware package. In the areas of the head plate that can receive nuts behind, use the longer bolts and nuts as required. You will notice that with a drive socket and an extension you can reach through several of the sprocket holes to place some of the above described bolts and or nuts. Go ahead and torque these bolts and or bolts and nuts to 35 ft. lbs. torque. Use a large screw driver to move the flex plat teeth against the bottom of the engine mount plate to rotate the crankshaft and thus the sprocket to be able to install remaining bolts until all twelve are installed. During this process there are two of these bolts that attach the aluminum block braces, one to each engine head. (One is 3 ¾ long and one is 3 long.) Because the engine heads are offset, one block brace is further from the mount plate than the other. Use the enclosed small round spacer between this block and the mount plate. Place a 3/8 nylon After the mount half of the propeller hub is installed it is time to put the 90 weight gear oil into the roller bearing area of the driven sprocket. Notice that there are two 1/8 allen head pipe plugs in the sides of the sprocket. Rotate the sprocket (by the large screw driver method on the flex plate) until one of the plugs is about one inch higher than the other. Remove the two pipe plugs. Using a 90 weight gear oil spout type container (The auto parts Water Walker, LLC Page 4 8/17/2007

5 houses sell a quart container with a tapered small spout) insert oil slowly from the higher pipe plug hole until the oil just begins to drain from the lower pipe plug hole. Let it settle there, wipe off any excess and replace the plugs. You now have the internal cavity slightly less than half full of 90 weight gear oil for the bearings to run in. This oil should be replaced from time to time, say in a year. The rear end of your pickup truck uses the same type oil and it lasts for years in that assembly. Water Walker, LLC Page 5 8/17/2007

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-46. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. b06x6x Neutral st Gear Mainshaft Mainshaft 4 5 4 5 Countershaft Out

More information

INSTRUCTIONS FOR INSTALLATION OF THE CH-2 and CH-3 DRIVE UNIT TO AN ENGINE WARNING

INSTRUCTIONS FOR INSTALLATION OF THE CH-2 and CH-3 DRIVE UNIT TO AN ENGINE WARNING INSTRUCTIONS FOR INSTALLATION OF THE CH-2 and CH-3 DRIVE UNIT TO AN ENGINE WARNING! Never reach hands or other body parts in or near moving parts!! Maintain a safe distance from any fixed or moving propeller!!

More information

Assembly Manual. 1/10th Formula 1 Car

Assembly Manual. 1/10th Formula 1 Car Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-45. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. Mainshaft Neutral Mainshaft st Gear b06x6x Countershaft 4 Out 5 Countershaft

More information

Rotax Sprag Replacement

Rotax Sprag Replacement Rotax Sprag Replacement This is intended as a full walk through on a Sprag replacement on a Electric start Rotax engine These instructions were made from a sprag replacement on an MT 350 Tools List Non

More information

Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS

Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS Front Drive System - Big Block Chevy Installation Instructions Big Block Chevy with AC & with PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for install Jack Jack

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

MM Rear Coil-Over Kit - Bilstein Shocks (MMCO-3)

MM Rear Coil-Over Kit - Bilstein Shocks (MMCO-3) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Rear Coil-Over Kit - Bilstein Shocks (MMCO-3) Read all instructions before

More information

Maintenance Information

Maintenance Information 45528270 Edition 1 June 2007 Barring Motor T480 Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this Barring Motor.

More information

HORSTMAN GREASED LIGHTNING CLUTCH

HORSTMAN GREASED LIGHTNING CLUTCH HORSTMAN GREASED LIGHTNING CLUTCH Horstman s Greased Lightning (GL) clutch is designed for ultra high performance, and requires expert setup and a serious commitment to maintenance. Warning!!! 1. Clutch

More information

Geared Drives 200Z PSRU Zero Offset Gearbox with Centrifugal Clutch Assembly

Geared Drives 200Z PSRU Zero Offset Gearbox with Centrifugal Clutch Assembly Instructions for Removing and replacing Gen X Gearbox with Geared Drives 200Z Prior to your gear box arriving: Using a strap or chain and an engine hoist to hold your engine up in the mount, remove your

More information

RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.

RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS. RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR 2007-2016 JEEP WRANGLER ALL MODELS. Rear Bumper Installation Instructions 1) Remove factory rear bumper, (this includes all tow hitch

More information

ALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions

ALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions ALL AMERICAN BILLET Front Drive System - Small Block Ford Installation Instructions Small Block Ford with AC & PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for

More information

»Product» Safety Warning

»Product» Safety Warning C2402, C2602 Installation Instructions 2007-2013 Chevy 1/2 Ton 2wd Pickup 4.5", 6.5" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of

More information

»Product» Safety Warning

»Product» Safety Warning #F1422 Installation Instructions 2008-2010 Ford Super Duty F250/350 4wd 4" Radius Arm Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of

More information

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info* DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

»Product» Safety Warning

»Product» Safety Warning #F1424 Installation Instructions 2011 Ford Super Duty F250/350 4wd 4" Radius Arm Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle.

More information

IMCO SCX SERIES INFORMATION, OPERATION & MAINTAINANCE

IMCO SCX SERIES INFORMATION, OPERATION & MAINTAINANCE IMCO SCX SERIES INFORMATION, OPERATION & MAINTAINANCE Warning! Warning! Warning! Danger! Warning! 1. SCX & SCX4 Drives will not fit on a standard gimbal helmet, IMCO HELMET: #05-8025 Black or #05-8027

More information

STERNDRIVE UNIT 3 A DRIVE SHAFT HOUSING

STERNDRIVE UNIT 3 A DRIVE SHAFT HOUSING STERNDRIVE UNIT 3 A 23262 DRIVE SHAFT HOUSING Table of Contents Page Specifications............................ 3A-1 Torque Specifications.................. 3A-1 Upper Drive Shaft Bearing Preload.......

More information

»Product» Safety Warning

»Product» Safety Warning #F1410 Installation Instructions 2017 Ford Super Duty F250/350 4WD 4" Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

»Product» Safety Warning

»Product» Safety Warning C2453/C2653 Installation Instructions 2014-2016 Chevy/GMC 1500 2WD 4.5"/6.5" Suspension Systems Read and understand all instructions and warnings prior to installation of product and operation of vehicle.

More information

BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).

BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special

More information

»Product» Safety Warning

»Product» Safety Warning J1400, J1401 Installation Instructions 1997-2006 Jeep TJ 4 Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information

SCION tc LOWERING SPRINGS Preparation

SCION tc LOWERING SPRINGS Preparation Preparation Part Number: PTR11-21100 PTR11-21100-50 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Locking Nut 4 2 Spring Bumper, Front 5 1 Instruction Form Hardware

More information

INSTALLATION. 200 Series. Alternator bracket designed for the Small Block Chevy using early non Vortec cast iron style heads (1955 & newer)

INSTALLATION. 200 Series. Alternator bracket designed for the Small Block Chevy using early non Vortec cast iron style heads (1955 & newer) INSTALLATION INSTRUCTIONS 200 Series Speedway P/N: 916-67955 Bill's Hot Rod P/N: 201 / 202 / 203 Alternator bracket designed for the Small Block Chevy using early non Vortec cast iron style heads (1955

More information

UNDERDOG RACING DEVELOPMENT URD Traction Bar Installation

UNDERDOG RACING DEVELOPMENT  URD Traction Bar Installation URD Traction Bar Installation Introduction: UNDERDOG RACING DEVELOPMENT Thank you for choosing the URD Traction Bar for two wheel drive street trucks. More models coming soon! This bar is a true bolt on

More information

The HMC-Lite Construction Guide

The HMC-Lite Construction Guide The HMC-Lite Construction Guide The Heavy Metal-Lite Chassis is constructed using two identical drive modules. The drive modules are constructed using 3 mechanical sub-assemblies. The drive modules are

More information

Assembly Manual. 1/10th World GT car

Assembly Manual. 1/10th World GT car Assembly Manual 1/10th World GT car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

Backwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit

Backwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit Backwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit 1. Throttle Cable Twin (CKC-41) 2. Carburetor VM30mm (CKC-40) 3. Loctite 242.5mL (A-210) 4. Air Cleaner Filter 6000 (EC-86) 5. Rev

More information

Self-propelled Chipper Shredder Vacuum

Self-propelled Chipper Shredder Vacuum 2.11. Confirm that the drive gears are installed on the correct side. See Figure 2.11. 3. TRANSMISSION REMOVAL 3.1. Disconnect the H.T. lead from the spark plug. 3.2. Remove collection bag or blower chute.

More information

Timing belt change. Timing belt change

Timing belt change. Timing belt change Timing belt change Put 2 new Gates T275 timing belts on today. Tensioner drilled smooth and tight with less than 16,000 miles on her decided not to change the tensioners just the belts. You'll need some

More information

HKS 700E. Service Manual June Ver. 2.04

HKS 700E. Service Manual June Ver. 2.04 HKS 700E Service Manual 009 June Ver..04 HKS CO.,LTD 78 KITAYAMA FUJINOMIYA SHIZUOKA JAPAN 48-09 TEL +8(0)544-54-78 FAX +8(0)544-54-40 hks_aviation@hks-power.co.jp http://www.hks-power.co.jp/hks_aviation/

More information

Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion

Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern

More information

3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift

3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift 3.2 DRIVE TORQUE HUB Roll, Leak and Brake Testing 10 LUG PATTERN Torque-Hub units should always be roll and leak tested before disassembly and after assembly to make sure that the unit's gears, bearings

More information

Sport Performance Aviation LLC or or

Sport Performance Aviation LLC or or Sport Performance Aviation LLC Sales@FlywithSPA.com or 904.226.1881 Support@FlywithSPA.com or 904.563.4337 www.flywithspa.com Introduction Thank you for purchasing the Corvair rear generator kit from Sport

More information

ENG-14, Balance Shaft Oil Seal Replacement

ENG-14, Balance Shaft Oil Seal Replacement ENG-14, Balance Shaft Oil Seal Replacement Introduction The following procedure will provide instructions for replacing the balance shaft seals on a 944. It will also provide instructions for resealing

More information

Special Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

(1) License Plate Light (2) License Plate Plugs

(1) License Plate Light (2) License Plate Plugs PARTS LIST: 1 HD Replacement Bumper 4 12mm x 40mm Hex Bolts 1 Driver/Left Bracket 4 12mm Nylon Lock Nuts 1 Passenger/Right Bracket 8 12mm x 37mm x 3mm Oversize Flat Washers 2 Thin Side Spacers 4 Rubber

More information

FORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1)

FORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1) FORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack

More information

Installation Instructions

Installation Instructions 2003-Present Toyota 4Runner 2007-2014 FJ Cruiser LRT 3" Lift Kit by Low Range Off-Road (SKU# LR-LRFJ4RU) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when

More information

Owner smanual. Banks Billet TM Torque Converter Chevy/GMC Duramax Allison Transmission. with Installation Instructions

Owner smanual. Banks Billet TM Torque Converter Chevy/GMC Duramax Allison Transmission. with Installation Instructions with Installation Instructions Owner smanual Banks Billet TM Torque Converter 2001-2010 Chevy/GMC Duramax Allison Transmission THIS MANUAL IS FOR USE WITH KITS 72510 Gale Banks Engineering 546 Duggan Avenue

More information

AmTryke Adult Recumbent Model JT2000 #50-FC-2000

AmTryke Adult Recumbent Model JT2000 #50-FC-2000 AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

C3 Syncro Drive Proclimb 1100 Installation Instructions

C3 Syncro Drive Proclimb 1100 Installation Instructions Revision 4 Nov 8-2013 201A Old Town Road, Sicamous, BC. V0E 2V4 Ph 250-833 3538 Fax 888-716 5903 www.c3powersports.com Thank you for purchasing a ProClimb M, ProCross F & XF SyncroDrive Note: This modification

More information

ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1)

ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1) ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack Stands

More information

»Product» Safety Warning

»Product» Safety Warning #F1420 Installation Instructions 2011 Ford Super Duty F250/350 4wd 4" Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit

M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure

More information

»Product» Safety Warning

»Product» Safety Warning J1300, J1301 Installation Instructions 1997-2006 Jeep TJ 3 Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information

»Product» Safety Warning

»Product» Safety Warning F1604 Installation Instructions 2011-12 Ford Super Duty F250/350 4wd 6" Radius Arm Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle.

More information

WD DODGE SUSPENSION LIFT KIT P/N

WD DODGE SUSPENSION LIFT KIT P/N 4/03/03 94-01 4WD DODGE 1500 3 SUSPENSION LIFT KIT P/N 10-46094 NOTE: Each lift kit, and options to lift kits, are packaged separately. Therefore installation procedures are covered in separate instructions.

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

Installation Instructions

Installation Instructions 86-95 Suzuki Samurai Rear Wheel Bearing Kit (SKU# SAX-RWB) Instructions also include:! Rear Hub Bolt Kit!!!! (SKU# SAX-AS)!! SJ410 Backing Plate!!!! (SKU# SAX-410)! SJ413 Rear Drum Brake Hardware Kit!

More information

The spacers can be made out of.750 round aluminum bar with a.3125 to.318 hole drilled in center.

The spacers can be made out of.750 round aluminum bar with a.3125 to.318 hole drilled in center. SECTION I : FRONT COVER INSTALLATION With Crankshaft, Camshaft and oil Galley plugs installed in engine, you need to verify that the front cover clears the oil galley plugs and fits on engine block. The

More information

Installation Instructions

Installation Instructions Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System.

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System. Part # 22020-979-989 Mustang Level 2 CoilOver System Front Components: 2230 Front CoilOver Strut Recommended Tools Rear Components: 2260 Rear Coilover 225899 Rear Lower StrongArms 226699 Rear Upper StrongArms

More information

REPAIR INSTRUCTION - MP4120-SWS/MP4124-SWS

REPAIR INSTRUCTION - MP4120-SWS/MP4124-SWS Disassembly sequence REPAIR INSTRUCTION - MP4120-SWS/MP4124-SWS 1. With a 27mm wrench, remove the three discharge plugs (#48) and three inlet plugs (#42A) from the manifold (#43). 2. Inspect the plug o-rings

More information

KIT # CSS-C SUSPENSION LIFT KIT

KIT # CSS-C SUSPENSION LIFT KIT 14385 Veterans Way Moreno Valley, CA 92553 Phone: (951) 571-0212 Fax: (951) 571-0215 2001-2010 CHEVROLET SILVERADO 1500 AND 2500 HD 4WD AND 2WD PICK-UP 1999-2010 CHEVY 2500 4WD PICK-UPS 2001-2010 2500

More information

Installation Instructions

Installation Instructions Instructions Created by an: 86-95 Suzuki Samurai Samurai Front Axle Knuckle Rebuild Kits (SKU# SAX-KRK) Installation Instructions Revised 6-6-14 Suggested Tools: CAUTION: Safety glasses should be worn

More information

»Product» Safety Warning

»Product» Safety Warning #J1453 Installation Instructions 1993-1998 Jeep ZJ 4 Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products recommends

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

2001 Toyota MR ENGINES' '1.8L 4-Cylinder

2001 Toyota MR ENGINES' '1.8L 4-Cylinder TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator

More information

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,

More information

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 LTO SPORT KIT FOR OVAL RACING. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly

POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly DISASSEMBLY: 1. Remove pump from car and allow to drain. 2. Remove pulley from front of pump. This requires

More information

DYNATRAC THE PERFORMANCE AXLE SPECIALIST

DYNATRAC THE PERFORMANCE AXLE SPECIALIST DYNATRAC THE PERFORMANCE AXLE SPECIALIST DynaLoc Installation Instructions, Appendix A iinformation: Dynatrac has included an additional bushing in the DynLoc kit. Part DA60-0022-L will be referred to

More information

Patriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector)

Patriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector) Aluminum and Steel 5spring Qty. Component Parts Description: LONG BOX: (1) 103 Aluminum Tarp Axle (2) 98 Upper Arms with 90 Degree Elbow (2) Lower Aluminum ( 84 ) (1) Aluminum Cross Tube SMALL HARDWARE

More information

Range Road RR20T Firewood Processor. Crated Unit Assembly Manual

Range Road RR20T Firewood Processor. Crated Unit Assembly Manual Range Road RR20T Firewood Processor Crated Unit Assembly Manual Crated Unit 1.) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2.) Lift top of Metal crate off and move out of work area.

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 SPORT 3.2 KIT. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED VIEW

More information

88cc Big Bore Kit Install Instructions

88cc Big Bore Kit Install Instructions 88cc Big Bore Kit Install Instructions Before installing a big bore kit, you should first install a high volume oil pump. A high volume oil pump will deliver up to 300% more oil to your top end which will

More information

The HMC Heavy Metal Chassis Construction Guide using Timing Pulleys and Belts

The HMC Heavy Metal Chassis Construction Guide using Timing Pulleys and Belts The HMC Heavy Metal Chassis Construction Guide using Timing Pulleys and Belts The Heavy Metal Chassis is constructed using two identical drive modules. Power can be transmitted from the motors to the wheels

More information

Vibration Damper - Installation (0-118) Fan Hub - Installation (0-119)

Vibration Damper - Installation (0-118) Fan Hub - Installation (0-119) Vibration Damper - Installation (0-118) Section 0 - Engine Disassembly and Assembly - Group 00 Page 0-110 B Series Shop Manual 10 mm Install the package. Torque Value: 24 N m [18 ft-lb] Vibration Damper

More information

HEIDTS SUPERIDE IRS INSTALLATION INSTRUCTIONS INDEPENDENT REAR SUSPENSION

HEIDTS SUPERIDE IRS INSTALLATION INSTRUCTIONS INDEPENDENT REAR SUSPENSION HEIDTS SUPERIDE IRS INDEPENDENT REAR SUSPENSION Please read these instructions completely before starting your installation. Remember the basic rule for a successful installation: Measure Twice, Weld Once.

More information

'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS

'99-03 CHEVROLET/GMC IFS 4WD 6 SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS 1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures

More information

Click Here to Go Back AT THIS POINT AT THIS POINT. 9. Remove the driven gear from the crank balancer. Account for a key.

Click Here to Go Back AT THIS POINT AT THIS POINT. 9. Remove the driven gear from the crank balancer. Account for a key. Click Here to Go Back Fig. 3-398 Fig. 3-400 CC197D To service the driveshaft and/or countershaft, see Servicing Center Crankcase Components in this sub-section. NOTE: For efficiency, if the driveshaft

More information

Read and understand all instructions and warnings prior to installation of system and operation of vehicle.

Read and understand all instructions and warnings prior to installation of system and operation of vehicle. 102 S. Michigan Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech@bds-suspension.com Part#: 023620 Product: 6" Suspension System Application: 2009-2012 Ford

More information

FULL FLOATER HUB KIT INSTRUCTION MANUAL

FULL FLOATER HUB KIT INSTRUCTION MANUAL FULL FLOATER HUB KIT INSTRUCTION MANUAL WARNING: All components are shipped assembled for illustration purposes only. IT IS YOUR RESPONSIBILITY FOR FINAL ASSEMBLY. Please read instructions thoroughly before

More information

Installation Instructions

Installation Instructions Instructions Created by an: 2007-Present Toyota Tundra LRT Leveling Lift Kit - 4WD by Low Range Off-Road (SKU# LR-LRTundra) Instructions also apply to 2WD Kits. Installation Instructions Revised 7-11-17

More information

The HMC Heavy Metal Chassis Construction Guide

The HMC Heavy Metal Chassis Construction Guide The HMC Heavy Metal Chassis Construction Guide The Heavy Metal Chassis is constructed using two identical drive modules. The drive modules are constructed using 4 mechanical sub-assemblies. The drive modules

More information

Kysor On/Off Rear Air Fan Drive

Kysor On/Off Rear Air Fan Drive . Proper precautions must be taken to prevent personal injury from contact with moving parts, unintended engine start or other hazards present when working with powered equipment. Refer to the vehicle

More information

PORSCHE V TO 32V CAM GEAR CONVERSION INSTRUCTIONS. For all 16V engines: USA 78-84, Euro

PORSCHE V TO 32V CAM GEAR CONVERSION INSTRUCTIONS. For all 16V engines: USA 78-84, Euro PORSCHE 928 16V TO 32V CAM GEAR CONVERSION INSTRUCTIONS For all 16V engines: USA 78-84, Euro 77-86 2.0 cams@mrtubby.net Required parts not included in kit (2) HTD 32V cam gears - sprocket 928.105.530.01

More information

LEXUS IS 250/350/250 AWD REAR GS SHOCK ABSORBERS Preparation. Part Number: PTR PTR PTR

LEXUS IS 250/350/250 AWD REAR GS SHOCK ABSORBERS Preparation. Part Number: PTR PTR PTR Preparation Part Number: PTR13-53082 PTR13-53092 PTR13-53095 Kit Contents Item # Quantity Reqd. Description 1 1 Shock Absorber 2 1 Hardware Bag 3 Hardware Bag Contents Item # Quantity Reqd. Description

More information

Super 1050 Chain Saw UT Page 1 of 16 Carburetor Chamber

Super 1050 Chain Saw UT Page 1 of 16 Carburetor Chamber Super 1050 Chain Saw UT-10139 Page 1 of 16 Carburetor Chamber Super 1050 Chain Saw UT-10139 Page 2 of 16 Carburetor Chamber 1 58319A 1 RING- Retaining 2 592301 1 COVER- Air filter 3 A70326 1 NUT- Cover

More information

Hydraulic Automatic Primary Chain Tensioner for Sportsters

Hydraulic Automatic Primary Chain Tensioner for Sportsters Hydraulic Automatic Primary Chain Tensioner for Sportsters Installation Instructions Note: The factory service manual or equivalent for your motorcycle is highly recommended before attempting to install

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh

More information

FRONT AXLE - 9 1/4 AA

FRONT AXLE - 9 1/4 AA DR FRONT AXLE - 9 1/4 AA 3-45 FRONT AXLE - 9 1/4 AA TABLE OF CONTENTS page FRONT AXLE - 9 1/4 AA DESCRIPTION......................... 45 OPERATION........................... 45 DIAGNOSIS AND TESTING................

More information

Ford Racing GT500 Style Strut Mount Upgrade (05-12 All):

Ford Racing GT500 Style Strut Mount Upgrade (05-12 All): Ford Racing GT500 Style Strut Mount Upgrade (05-12 All): Required tools: (2) Jack stands Floor jack (1 is required but 2 is preferred) Torque wrench Spring compressor tool (can be rented at your local

More information

07 & UP GM 1500 PICKUP 2.0 FRONT 1.0 REAR LEVELING KIT INSTALLATION

07 & UP GM 1500 PICKUP 2.0 FRONT 1.0 REAR LEVELING KIT INSTALLATION INSTRUCTION PART NO 15265 LEVELING KIT NO 3813 07 & UP GM 1500 PICKUP 2.0 FRONT 1.0 REAR LEVELING KIT INSTALLATION READ INSTRUCTIONS/WARNINGS COMPLETELY THROUGH BEFORE STARTING. FAILURE TO ADHERE TO THE

More information

INSTALLATION. 200 Series. Air Conditioner bracket designed for the Small Block Chevy using early non Vortec cast iron style heads (1955 & newer)

INSTALLATION. 200 Series. Air Conditioner bracket designed for the Small Block Chevy using early non Vortec cast iron style heads (1955 & newer) INSTALLATION INSTRUCTIONS 200 Series Speedway P/N: 916-67956 Bill's Hot Rod P/N: 204 / 205 / 206 Air Conditioner bracket designed for the Small Block Chevy using early non Vortec cast iron style heads

More information

Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited)

Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited) Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited) Installation Time: 6 Hours Tools Required: Floor Jack Jack Stands Ratchet Torque Wrench 15mm Socket 15mm

More information

For the 4 lift application we recommend an 18 wheel not to exceed 9 in width with 5 of backspacing/ 0 offset and a 275/65-18 tire.

For the 4 lift application we recommend an 18 wheel not to exceed 9 in width with 5 of backspacing/ 0 offset and a 275/65-18 tire. 921221200F *1221BAG16* 1221BAG16 2015-18 Colorado/ Canyon 4 and 6 Lift Kit Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs

More information

Instructions to install the early ( ) Limited Slip Differential in the Late-model ( ) G28 Transaxle

Instructions to install the early ( ) Limited Slip Differential in the Late-model ( ) G28 Transaxle Instructions to install the early (1978-83) Limited Slip Differential in the Late-model (1985-1995) G28 Transaxle BACKGROUND: Most 928 owners know about the improvements to the 5- speed transaxle that

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-3 1965-72 GM A-BODY 10 & 12 BOLT AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time

More information

Ford 9 XD Aussie-Locker Install Instructions.

Ford 9 XD Aussie-Locker Install Instructions. Ford 9 XD-45831 Aussie-Locker Install Instructions. Before the install check the following. 1. Must be 31 spline 4-pinion carrier. 2. Must be an open carrier not a limited slip. 3. Refer to Ford or vehicle

More information

1992 Mitsubishi 3000GT VR-4

1992 Mitsubishi 3000GT VR-4 TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner

More information

INSTALLATION INSTRUCTIONS 89551

INSTALLATION INSTRUCTIONS 89551 INSTALLATION INSTRUCTIONS 89551 For Rancho Suspension System RS66551B: Ford F250, F350 Super Duty 4x4 DIESEL ONLY (Single Rear Wheels Only With or Without Auxiliary Spring). (WILL NOT WORK ON GAS ENGINES

More information

»Product» Safety Warning

»Product» Safety Warning F2650 Installation Instructions 2017-18 Ford F150 4WD 4-6" Suspension Systems Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information