PNEUMATIC TOOLS Below are examples of the merchandised range, please contact your sales rep for more details on how to order store concepts*.

Transcription

1 PNEUMATIC TOOLS Below are examples of the merchandised range, please contact your sales rep for more details on how to order store concepts*. *Concepts may change from time to time and without notice, due to stock availability, updating and/or discontinuation of certain products Industry Leaders Established 1977 For more information: Tel: Fax: Visit our website:

2 PNEUMATIC TOOLS Blowers Air Duster Blow Gun Short nozzle Maximum pressure: 9 bar Min compressor required: 1.1KW Pressure required: 3-8 bar Suitable for blowing and cleaning away cuttings etc Extended nozzle Air inlet: 6.5mm Suitable for unblocking oilways in engines & machine parts, cleaning electrical circuit boards & computers, general cleaning duties in & around the workshop Inflating Gun TOOS Tyre Inflator PAB Blowers / Inflators / Wash Guns / Under Coating Guns Suitable for: Inflating car tyres, bicycle tyres, air beds & inflatables, footballs etc Wash Guns PAB Paraffin Spray Gun Cup capacity: 1000cc Working pressure: 5 bar Adjustable nozzle for fine or course spray Suitable compressor: 1.1KW/ 24L & above Use to clean: Motor vehicles, boats, engines & outer components Lubrication of suspension parts & machinery TOOS Under Coating Gun Undercoating Gun Washing Gun Working pressure: kPA (4-7 bar) 6mm Air intake Need to connect to a 1/2 or 12.5mm hose pipe Suitable for: Cleaning paths, drains & patios, cleaning garden furniture, cleaning grime from car bodywork; cleaning conservatory guttering & roofs; removing rust from underneath wheel arches & vehicle bodywork PAB Max Pressure: 90PSI/ 628kPA Working pressure: 60PSI/ 419kPA Air consumption: 11.3CFM/ 321L/min Feed type: Suction Air intake: Suction Min recommended compressor: 3HP/ 2.2KW TOOG Page 78

3 PNEUMATIC TOOLS Sand Blasting Guns Air Sand Blasting Kit Sand Blaster Gun 3 Spare 6.35mm nozzles 1 Air jet 1 Hex key wrench Complete with 3 meter hose and pick up tube Use to clean old paint, carbon and stubborn deposits. Adjust pressure between 304KPA & 659KPA until desired result is obtained. Minimum recommended comressor 2HP / 1.5kW Air Brush Set Air Brush Set Hand piece protective cap 22cc cup 5cc metal cap 60cc mixing jar with lid Spray jar Spanner PVC Airline hose with adaptors Suitable for: Hobby enthusiasts & model makers, fine spray nozzles, spraying with cellulose & enamel paints PAB Gravity Feed Spray Gun Fluid nozzle: 1.4mm Cup Capacity: 600ml Max operating pressure: bar Average air consumption: L/min Suitable compressor: 1.5KW or above TOOS TOOG Working pressure 6 bar Suitable for: Removing old paint, rust spots etc, renovation of plants & machinery Suction feed for blasting material Min air compressor required: 3HP/ 2.2KW industrial PAB Spray Guns - Gravity Feed Mini Gravity Feed Touch Up Gun - K3 Gravity flow cup 125ml Cup capacity Air inlet 1/4 Air pressure PSI Ave. air consumtion: CFM Adjustable spray pattern Fluid adjustment knob TOOS Gravity Feed Spray Gun Fluid nozzle: 1.5mm Plastic cup: 500cc Pattern width: mm Working pressure: kPA (3-4 bar) Air consumption: 350l/min - 12CFM Suitable for most types of paint spraying including cellulose & oil based paints; emulsion & gloss paints for walls & ceilings, low viscosity wood stain & varnish Suitable compressor: 2HP & above PAB Sand Blasting Guns / Air Brush Kits / Gravity Feed Spray Guns Gravity Feed Spray Gun Standard Nozzle: 1.4mm Cup Capacity: 0.6L Average Air Consumption: 8CFM/228L/min Recommended Air Pressure: 50-70PSI 3 Control adjustment valves: a) Paint flow b) Fan adjustment c) Air control Spare cup for S1789 TOOS TOOS Deluxe Mini HVLP Spray Gun Fluid nozzle: 1.4mm 30-80Psi Operating pressure L/min Air consumption 6.35mm NPS (M) Air connector 100ml Cup size Non bleeder type, gravity feed & external mix spray TOOS Page 79

4 PNEUMATIC TOOLS Spray Guns - Suction Feed Suction Feed Low Pressure Spraygun Feed type: Pressure Standard nozzle: 1.3mm Optional nozzle: 1.2mm Average air consumption: 3CFM / 85L/min Cup Capacity: 0.8L Recommended Air Pressure: 10-40Psi Canister Capacity: 0.8L Paint Nozzle: 1.3mm Suction Spray Gun Fluid nozzle: 1.5mm Aluminium cup: 1000cc Pattern width: mm Working pressure: kPA (3-4 bar) Air consumption: 350l/min - 12CFM Air inlet: 6.5mm Suitable for most types of paint spraying including cellulose & enamel paints; emulsion paint for walls & ceilings, low viscosity wood stain & varnish Suitable compressor: 2HP & above TOOS PAB Suction Feed Spray Guns / Accessory Kits Suction Feed High PressureSpray Gun Standard Nozzle: 1.6mm Cup Capacity: 1L Avg Air Consumption: 10CFM / 280L/min Recommended Air Pressure: kPA/ bar Canister Capacity: 0.8L Adjustable spray pattern Non-bleeder type, siphon feed External mix nozzle Dual Action trigger Air inlet 1/4 BSP Paint nozzle: 2.0mmØ Min recommended compressor: 2HP/ 1.5KW and above TOOS Spray Gun Holder TOOS Accessory Kits 5Pc Spray Gun & Accessory Kit Spray Gun Degreasing Gun Blow Gun Tyre inflator & connectors High Pressure Spray Gun Standard nozzle: 1.8mm Cup Capacity: 1L Average Air Consumption: 7CFM / 200L/min Recommended Air Pressure: 50-70PSI TOOS Pc High Pressure Spray Gun & Accessory Kit High pressure spray gun Paraffin spray gun Tyre Inflator Air duster Coiled hose PAB TOOS Page 80

5 PNEUMATIC TOOLS Pneumatic Sanders Grinders Drills Die Grinder 6mm Collet Die grinder 5x 6mm Moulded stones 2x Hand wrenches Connecting nipple Working pressure: 695kPA/ 6.5 bar Free speed: 22000RPM Air inlet: 6.5mm Collet: 6mm Avg air consumption at 100% duty cycle: 11CFM/ 311L/min Suitable compressor: 3HP and above Suitable for: grinding & smoothing rough castings; removing rust from metalwork; general workshop use, model making Dual Action Sander 150mm Pad Size Pad size: 150mm Free speed: 9000RPM Air inlet: 6.5mm Avg air consumption at 100% duty cycle: 14CFM/ 397L/min Working pressure: 659kPA/ 6.5 bar Min air compressor required: 3HP/ 2.2KW Suitable for: Finishing body filler, ideal for contoured surface Code no: Barcode: PAB PAB mm Angle Grinder Working pressure: 6.5 bar/ 659kPA Avg air consumption at 100% duty cycle: 14CFM/ 396L/min Disc size: 100mm x 16mm bore Free speed: 11000RPM Air inlet: 6.5mm Suitable compressor: 4HP/ 3KW and above Suitable for: Car body work & metal fabrication applications PAB /2 Impact Wrench & Socket Set PAB Pneumatic Wrenches Air Hammer 1/2 Impact wrench 10 x 1/2 Drive impact sockets: 9, 10, 11, 13, 14, 17, 19, 22, 24, 27mm 1/2 Drive extension bar Mini oiler Connecting nipple Tube oil air tool 16mm bolt capacity 7000RPM free speed Avg air 100% duty cycle: 23CFM/652L/min Working pressure: 659kPA/ 6.5 bar Min air compressor required: 3HP/ 2.2KW Suitable for: automotive applications, removing vehicle wheel nuts, metal construction applications Reversible Air Drill 10mm Drill capacity 6.5mm air inlet 1800RPM free speed Working pressure: 608kPA/ 6.5 bar Avg air 100% duty cycle: 200L/min Fitted with a 10mm keyless chuck Suitable for: All types of wood & metal drilling, workshop & automotive use PAB mm Drive Ratchet Wrench 1/2 Drive ratchet 9, 10, 11, 13, 14, 17, 19mm 7 x 1/2 drive sockets 2 x extensions Swivel Connecting nipple We recommend the use of an inline lubricator (PAB1222) from the TRADEair range of accessories. You will also require an air hose to connect to your compressor Suitable for: fast removal & refitting of nuts; ideal for production line environment PAB Pneumatic Sanders / Grinders / Drills / Wrenches / Hammers Chipping Hammer Set Air hammer 4 x Chisels Spring retainer Connecting nipple. Required air pressure: 628kPA/ 6.2 bar Avg air cons.: 5CFM/141L/min Max speed: 3000blow/min Air intake: 1/4 Suggested air compressor: 2HP/ 1.5KW or larger Suitable for: chipping tiles, paving & brickwork etc, sheet metal fabrication PAB Page 81

6 PNEUMATIC TOOLS Nail Gun Staple Gun Staples Nails Nailer/ Staple gun Working pressure: 608kPA/ 6 bar Avg air consumption at 100% duty cycle: 5CFM/ 142L/min 65mm Air intake Minimum compressor required: 2HP/ 1.5KW Uses F series nails: 10-32mm PAB1366 F10/ PAB1367 F15/ PAB1368 F20/ PAB1369 F25/ PAB1370 F30 Uses ffg staples: 6-32mm PAB mm long/ PAB mm long/ PAB mm long Suitable for: nailer - fixing mouldings, cladding & picture framing, stapler - use in upholstery Finishing Nailer Working pressure: 608kPA/ 6 bar Uses T series nails Nails: 15-50mm Suitable for: Fixing mouldings, cladding & picture framing See page 38 for Nails PAB PAB Guage Staples 1000Pc 18 Guage Air Nails 1000Pc Pneumatic Guns / Lubricators PAB mm Staples PAB mm Staples PAB mm Staples For use on TRADEair stapler PAB1350 Filters Lubricators Inline Lubricator Helps to reduce wear on air tools. Automatically lubricates air line system 6.35mm thread PAB PAB F10 Air nails PAB F15 Air nails PAB F20 Air nails PAB F25 Air nails-1.22mm PAB F30 Air nails For use on TRADEair stapler PAB1350 & PAB mm Pressure Regulator/ Water Filter Designed to reduce moisture content in the air flow and adjust the air pressure 6.5mm female inlet & outlet Complete with pressure guage sockets Manual pressure adjustment PAB /4 Regulator & Water Trap Combo 1Lt Air Compressor Oil Maximum inlet pressure : (150PSI) Maximum temperature: 60ºC (140F) Maximum pressure: 10 bar TOOR TOOO Page 82

7 PNEUMATIC TOOLS Hose Fittings Tail Pieces Couplings 1/4 Bsp Female Air Quick Coupler 1/4 Bsp Male Air Connector 1/4 Bsp Female Air Connector TOOC TOOC TOOC mm Air Hose Connector 8mm Hose to 1/4 BSP Male Fitting Connector 6mm Hose To Split Nut Fitting TOOC TOOC TOOC Pc 8mm Air Hose Connector Set 8mm Hose to 6.35mm BSP male fitting 6.35mm BSP male connector 6.35mm BSP female air quick coupler 6.35mm BSP female air connector 8mm connector PVC High Pressure Hose PVC Airline Hose With Fittings Double layer re-inforced PVC airline hose Resistant to fuels, oils, solvents & chemicals Strong polvin/ nylon contruction 1750kPA Test pressure 6mm x 10m length with fittings Will not kink and reduce air flow N.O.S.A blue, colour coding TOOH TOOC PVC High Pressure Air Hose TOOH mm x 20m TOOH mm x 20m TOOH mm x 20m TOOH mm x 100m TOOH mm x 100m TOOH mm x 100m Abrasion resistant air/ water hose Weather resistant wont kink Ideal for high pressure lines & compressors 1750kPA Pressure Rubber High Pressure Air Hose TOOH mm x 20m TOOH mm x 20m TOOH mm x 100m TOOH mm x 100m TOOH mm x 100m Abrasion resistant air/ water hose Weather resistant wont kink Ideal for high pressure lines & compressors 1750kPA Pressure Hose Fittings / Couplings / Air Hoses Ultra-light & super strong 100% rubber 40% lighter -50º to 190ºF unmatched versatility genuine flexibility & usability in extreme conditions Ozone resistant cover - resists extreme weather, abrasions and kinks oil resistant core tube & cover high strength polyester braided reinforcement Rubber Air Line Hose Warranty Explained Product is warranted to be free from defects in material and workmanship for a period of 10 years from the date of original purchase subject to the disclaimers and limitations stated below. 8mm x 100MT The blubird warranty is an express limited warranty to the original purchaser. This warranty does not cover a defect TOOH resulting from abuse, misuse, neglect, or any use not in conformity with the printed directions or commonly intended application of the product. the purchaser is urged to inspect the product upon purchase. -50º TO 190º F INNER DIAMETER 8MM Rubber Air Line Hose 8mm x 20MT TOOH WORKING PRESSURE 20BAR SAFETY FACTOR 4:1 Page 83

8 DIRECT DRIVE COMPRESSORS REF KEY In order to maintain the manufacturers stated warranty, please adhere strictly to the following recommended duty cycles: Direct Drive 2HP/3HP 60% Duty Cycle ( 6 minute run/4 minute rest) If the compressor runs for longer than the stated times, please adjust usage or air tool type accordingly. The ratings are suggested usage for optimal running expectancy of your compressor SUITABLE SUITABLE MCFRC KW / FAD 1.7 CFM MCFRC100 MCFRC108 FAD 2.3 CFM MCFRC102A MCFRC109 FAD 3.7 CFM MCFRC103 FAD 3.7 CFM MCFRC113 FAD 5.8 CFM MCFRC241 FAD 1.7 CFM MCFRC242 FAD 2.6 CFM MCFRC243 FAD 5.3 CFM MCFRC244 FAD 5.3 CFM NON USABLE Air Dusters Tyre Inflator Air Nailer Air Brush Air Stapler Touch-up Gun Low Pressure Spray Gun High Pressure Spray Gun Air Drill Air Screwdriver Die Grinder Angle Grinder Palm Sander Orbital Sander Impact Wrench 3/8-1/2 The above air tool recommendations are based on Average CFM = 25% duty cycle of tool ( i.e. continuous running for 15 seconds)

9 BELT DRIVE COMPRESSORS REF KEY In order to maintain the manufacturers stated warranty, please adhere strictly to the following recommended duty cycles: Belt Drive 2HP/3HP 80% Duty Cycle (8 minute run/2 minute rest). If the compressor runs for longer than the stated times, please adjust usage or air tool type accordingly. The ratings are suggested usage for optimal running expectancy of your compressor SUITABLE SUITABLE MCFRC221 FAD 3.5 CFM MCFRC222 FAD 7.0 CFM MCFRC227 FAD 8.8 CFM MCFRC228 FAD 8.8 CFM MCFRC229 FAD 8.8 CFM MCFRC KW / FAD 9.3 CFM MCFRC KW / FAD 12.3 CFM NON USABLE Air Dusters Tyre Inflator Air Nailer Air Brush Air Stapler Touch-up Gun Low Pressure Spray Gun High Pressure Spray Gun Air Drill Air Screwdriver Die Grinder Angle Grinder Palm Sander Orbital Sander Impact Wrench 3/8-1/2 The above air tool recommendations are based on Average CFM = 25% duty cycle of tool ( i.e. continuous running for 15 seconds)

10 /INDUSTRIAL PNEUMATIC TOOLS Blow Guns 100mm Air Blow Gun 300mm Air Blow Gun Body material: Plastic P.O.M Nozzle material: Steel Nozzle length: 100mm Working pressure: 115PSI/ 8kg/cm 2 Max pressure: 156PSI/ 11kg/cm 2 Air inlet: 1/4 PT (NPT) Body material: Plastic P.O.M Nozzle material: Steel Nozzle length: 100mm Working pressure: 115PSI/ 8kg/cm 2 Max pressure: 156PSI/ 11kg/cm 2 Air inlet: 1/4 PT (NPT) PUAA PUAA Air Blow Gun Air Duster Heavy Duty Pneumatic Guns Body material: Aluminium Nozzle material: Aluminium Working pressure: 115PSI/ 8kg/cm 2 Max pressure: 156PSI/ 11kg/cm 2 Air inlet: 1/4 PT (NPT) PUAA Air Grease Gun Capacity (bulk): 400cc Capacity (cartridge): 14oz Pressure tested: PSI at PSI Loading ways: C105 - Stand 14 or 14.5 / C107: Grease cartridge / C108: Loading with dispenser / C109: Loading with bulk grease Min compressor required: 2HP PUAT Deluxe Mini HVLP Spray Gun Body material: Aluminium Nozzle material: Aluminium Working pressure: 115PSI/ 8kg/cm 2 Max pressure: 156PSI/ 11kg/cm 2 Air inlet: 1/4 PT (NPT) Spray Guns PUAA High Pressure Spray Gun Nozzle: 0.3mm Working air pressure: 15-45PSI Air consumption: CFM Cup capacity: 20cc, Screw-on type cup Double action trigger - air/paint control Adaptor permits use with propel can or air compressor Excellent for fine art work and hobby crafts such as: photo-retouching, fine drawings, illustrations, pricing plastic items by application of colour inks, watercolours, lacquers, design colours,acrylic colours etc Light USE PUAB Pneumatic Accessories Oil & Water Separator 1/4 Mini In-Line Oiler Standard nozzle: 1.6mm Optional nozzle: 1.0mm, 1.5mm, 1.8mm & 2.0mm Feed type: Suction Capacity of cup: 1.0 litre Air inlet: 1/4 : 3/8 Average air consumption: 10CFM/280L/min Nett weight: 1.1kg Recommended air pressure: 30-50Psi Code no: Barcode: PUAS A good spray job requires clean air, free from oil & water This simple device is easily attached between your spray gun and air line and removes water and oil with very little pressure reduction PUAA mm female outlet + male inlet Do not use on spray guns PUAA Page 86

11 /INDUSTRIAL PNEUMATIC TOOLS Pneumatic Drills Screwdrivers 10mm Chuck Air Drill 13mm Chuck Air Drill 10mm Drilling capacity 1800RPM Free speed 6.5mm Air inlet Avg air 100% duty cycle: 7CFM Reversible pistol action Min compressor required: 2.5HP 13mm Drilling capacity 400RPM Free speed 6.5mm Air inlet Ave air 100% duty cycle: 10CFM Reversible pistol grip Min compressor required: 3HP Light USE PUAT PUAT mm Chuck Angle Air Drill 1800RPM Air Screwdriver 10mm Drilling capacity 1900RPM Free speed 6.5mm Air inlet Avg air 100% duty cycle: 7CFM Non reversible angle action Min compressor required: 2.5HP PUAT RPM Air Screwdriver 6.35mm Hex shank size 6mm Capacity bolt size 800RPM Free speed kg.cm Max Torque 1/4 Air inlet Ave air 100% duty cycle: 7CFM Pistol adjustable clutch 6.5 bar Working air pressure Min compressor required: 2.5HP PUAT4080A mm Dual Action Air Sander 6.35mm Hex shank size 6mm Capacity bolt size 1800RPM Free speed kg.cm Max Torque 1/4 Air inlet Avg air 100% duty cycle: 7CFM Pistol adjustable clutch 6.5 bar Working air pressure Min compressor required: 2.5HP PUAT Pneumatic Grinders Sanders 125mm Air Angle Grinder Free speed: RPM Air inlet: 6.5mm Average air consumption at 100% duty cycle: 14CFM Min compressor required: 4HP PUAT Pneumatic Sanders 5 Air Orbital Sander Heavy Duty Drills / Drivers / Grinders / Sanders Spindle thread: 150mm Free speed: 9000RPM Air inlet: 6.5mm : 3/8 Average air consumption at 100% duty cycle: 14CFM Work air pressure: 6.5 bar Min compressor required: 4HP PUAT7015P Sanding paper: 93 x 228mm Free speed: 8000RPM Air inlet: 6.5mm : 3/8 Average air consumption at 100% duty cycle: 14 CFM Work air pressure: 6.5 bar Min compressor required: 4HP Light USE PUAT Page 87

12 /INDUSTRIAL PNEUMATIC TOOLS Pneumatic Sanders Air Sander Pneumatic Die Grinders 1/4 Air Die Grinder PUAT Two piston Free speed: 22000RPM Overall length: 160mm Air inlet: 6.5mm Capacity bolt size: 6mm Average air consumption at 100% duty cycle: 11 CFM Work air pressure: 6.5 bar Min compressor required: 3HP Light USE PUAT /4 Air Die Grinder Kit 1/4 Extended Air Die Grinder 1x AT7033 1x Blow case 2x Wrenches 10 x Grinding stones Free speed: 22000RPM Overall length: 160mm Air inlet: 6.5mm Capacity bolt size: 6mm Average air consumption at 100% duty cycle: 11 CFM Work air pressure: 6.5 bar Min compressor required: 3HP Free speed: 25000RPM Air inlet: 6.5mm Average air 100% duty cycle: 5 CFM Work air pressure: 6.5 bar Min compressor required: 2.5HP Heavy Duty Sanders / Grinders / Wrenches Light USE PUAT7033K Pneumatic Impact Wrenches 17Pc 12.5mm Drive Impact Wrench Kit 1Pc AT Pc Air Sockets: 10,11,12,13,15,17,19,21,22,24,mm 1Pc 5 Extension Bar 1Pc Oil Pot 1Pc Hex Wrench 1Pc Nipple 1Pc Plastic Case 1Pc Mini Oiler Packing: 4 Sets/Ctn/19kgs/ mm Bolt capacity 7000RPM Free speed 30kg/cm 220ft/lbs Max Torque 6.5mm Air inlet Avg air 100% duty cycle: 23CFM Single hammer clutch type Min compressor required: 5HP professional PUAT Light USE 12.5mm Drive Impact Wrench 16mm Bolt capacity 7000RPM Free speed 27kg/cm 220ft/lbs Max Torque 6.5mm Air inlet Avg air 100% duty cycle: 26CFM Working air pressure: 6.5 bar Single hammer clutch type Min compressor required: 4HP PUAT7033L PUAT mm Drive Impact Wrench 16mm Bolt capacity 7 000RPM Free speed 32kg/cm 230ft/lbs Max Torque 6.5mm Air inlet Avg air 100% duty cycle: 23CFM Pin clutch type Min compressor required: 5HP PUAT Page 88

13 /INDUSTRIAL PNEUMATIC TOOLS Pneumatic Impact Wrenches 12.5mm Drive Impact Wrench 12.5mm Drive Impact Wrench 16mm Bolt capacity 7 000RPM Free speed 230kg/cm 350ft/lbs Max Torque 6.5mm Air inlet Avg air consumption 100% duty cycle: 27CFM Pin clutch type Min compressor required: PUAT mm Drive Impact Wrench 25mm Bolt capacity 4500RPM Free speed 69kg/cm 500ft/lbs Max Torque 10mm Air inlet Avg air 100% duty cycle: 30CFM Single hammer clutch type Min compressor required: 7.5HP PUAT x 25mm Drive Impact Wrench 32mm Bolt capacity 3000RPM Free speed 152kg/cm 900ft/lbs Max Torque 12.5mm Air inlet Avg air 100% duty cycle : 53CFM Twin hammer clutch type Min compressor required: 10HP PUAT mm Bolt capacity 7000RPM Free speed 55kg/cm 400ft/lbs Max Torque 6.5mm Air inlet Avg air 100% duty cycle: 23CFM Twin hammer clutch type Min compressor required: 5HP PUAT mm Drive Impact Wrench 19mm Bolt capacity 4200RPM Free speed 100kg/cm 700ft/lbs Max Torque 6.5mm Air inlet Avg air 100% duty cycle: 30CFM Pin clutch type Min compressor required: 7.5HP PUAT Pneumatic Ratchet Wrenches 10mm Drive Air Ratchet Wrench 10mm Bolt capacity 160RPM Free speed 6.9kg/cm 50ft/lbs Max Torque 6.5mm Air inlet Avg air 100% duty cycle: 18CFM Twin hammer clutch type Min compressor required: 2.5HP Light USE PUAT Heavy duty Pneumatic Sanders / Grinders / Drills / Wrenches / Hammers 13mm Drive Air Ratchet Wrench 1Lt Air Tool Oil 13mm Bolt capacity 160RPM Free speed 6.9kg/cm 50ft/lbs Max Torque 6.5mm Air inlet Avg air 100% duty cycle: 18CFM Single hammer clutch type Min compressor required: 2.5HP PUAT Lght USE For in-line lubrication of air tools With rust inhibitors to prevent internal corrosion of components TOOO Page 89

14 /INDUSTRIAL PNEUMATIC TOOLS Pneumatic Hammer 190mm Air Hammer With 4 Chisels (Round) 1 Pc Air hammer 1 Pc Air nailer scaler attachment (AT-2071) 1 Pc Inlet adaptor 1 Pc Mini oiler 1 Pc Retainer 5 Pc 7 Chrome molybdenum chisels Universal Spring Retainer For use with PUMA 190mm Air hammer PUAT2020/R PUAT Heavy Duty Pneumatic Hammers, Rivet Guns, Staplers & Nailers Chisel shank: 10mm Piston bore: 19.05mm Piston stroke: 66mm Blow per minute: 3 000RPM Air inlet: 6.5mm : 3/8 Avg air consumption at 100% duty cycle: 9CFM Min compressor required: 3HP PUAT2020/R Pneumatic Rivet Guns 4.8mm Air Hydraulic Riveter PUAT industrial Air Stapler PUMA Pneumatic Fasteners Nails - F Series PUAT Traction power: 720kg Stroke length:14mm Overall length: 273mm Air inlet: 1/4 Average air consumption at 100% duty cycle: 4 CFM Nett weight: 1.5kg Work air pressure: 6.5 bar Min compressor required: 2HP Pneumatic Staple Gun Nail Gun Crown: 11.2mm Shank width: 1.20mm Gauge 20 Uses J series staples Staple length: 10-22mm Average air 100% duty: 3CFM Min compressor required: 2HP Nails - T Series Air Hydraulic Riveter Kit Code no: Barcode: PUAT6015K AT6015 Air riveter joints Rivets Oiler Blowmould case Nose pieces: 3/32, 1/18, 5/32 3/16 Jaw case Jaw Jaw case joint Jaw pusher Return springs Valve pusher spring Jaw pusher spring Frame O-rings Frame back-up rings Oil piston O-rings & back-ups Hanging clip O-ring Frame joint O-ring & back ups Frame brass joint Valve pusher O-rings Valve Valve cap O-ring Air piston ring Lock nut O-ring Air cylinder O-ring Spanner gauge Spanner F30 Air Nailer Crown: 9.1mm Shank width: 1.25mm Gauge: 18 Uses F series staples Average air 100% duty: 5CFM Min compressor required: 2HP PUAT Staples - J Series Traction power: 720kg Stroke length:14mm Overall length: 273mm Air inlet: 1/4 Average air consumption at 100% duty cycle: 4 CFM Nett weight: 1.5kg Work air pressure: 6.5 bar Min compressor required: 2HP Code no: Spec: Barcode: F10 10MM F15 15MM F20 20MM F25 25MM F30 30MM Pc per box Guage: 18 Thickness: 1.25mm Code no: Spec: Barcode: T20 20MM T25 25MM T32 32MM T38 38MM T45 45MM T50 50MM Pc per box Guage: 16 Thickness: 1.6mm Code no: Spec: Barcode: 1010J 10MM J 13MM J 16MM J 19MM J 22MM Pc per box Guage: 20 Crown: 11.2mm Thickness: 0.6mm Page 90