Basic introduction to Points Page 1 of 12 Uncontrolled document for information only see disclaimer** on last page
|
|
- Egbert Wells
- 6 years ago
- Views:
Transcription
1 Basic introduction to Points Page 1 of 12 Uncontrolled document for information only see disclaimer** on last page Points are used to enable trains to switch tracks from one to another or into a station or siding etc. They are operated by electric powered point machines, hydraulically power clamplocks, torsion operated systems, air powered machines, mechanically operated points or train operated point machines (either by hydraulic type or spring). They also come in many different types of turnouts, these are as follows: LH & RH Turnouts (LH SHOWN) Known as Plain Leads Not all configurations are shown. Rail type: The track in the UK comes in various types, this is either Flat bottomed vertical, Flat bottomed inclined, Bull-head or UIC60 (European adopted rail). Bull head and UIC are disguisable by the way they look, but vertical and inclined look exactly the same. The only way to tell is by looking on the slide chairs it is mounted on. Either a V will be stamped on the chair for Vertical Rail, or X for Inclined. Vertical & Inclined rail are actually the same, it s the chairs it is mounted on that make it vertical or inclined.
2 Page 2 of 12 Basic layout of point equipment (track): Stretcher bars Types of Rail: Flat bottom and rare bull-head type rail UIC 54B type switch with UIC60 stock rail Switch length: The length of switch rails is determined by at what speed the train is to cross over to another track, the lengths are A,B,C,D,E,F,G,SG (small switch G ),H. The smallest switch is A for very slow speeds and up to H for very fast speeds. The length of switch will also determine how many stretchers should be fitted (minimum is two) and how long the backdrive will be. The switch length letter is found on the gauge blocks at the rear of the switch which hold the switch and stock together. Fastenings: The switch rail rests on slide chairs, some points are fitted with Austro or Schwihag rollers, the Austro rollers are becoming more obsolete as these take a full day to fit and are nonadjustable. The switch rail is only fixed at the rear to the stock rail by bolts and clips. The clips are either pandrol or fastclip type on modern points.
3 Page 3 of 12 Pandrol type E clip New modern fastclip type The slide chairs (also known as slide base plates ): Normal conventional non roller slide chair Schwihag type roller baseplate (modern) Austro-roller (becoming more obsolete) AS type chair screw used to secure the slide chairs to wooden sleepers only. M screws which are wider in diameter are used if AS screws no longer grip. Or Hilti coils are used instead (these are like large wall plugs). The track at each end is either welded together or fixed together by fishplates (left hand picture) or insulated block joints ( IBJs ) (right hand picture), if the track circuit voltage needs to be separated. Sometimes six hole insulated block joints are used which are insulated by glue and not plastic.
4 Track bed: Page 4 of 12 The points are mounted on mostly wooden timbers and on more modern layouts on concrete reinforced sleepers. On concrete sleepers different track components are used to secure the rails and to stop lateral movement. The track bed is made up of large stones known as ballast, this is compacted by hand using kango machines or a S&C (switch and crossing) tamping machine. The track is either level or has a cant, where it is on a bend and has to lean either left of right to enable trains to go around the bend at higher speeds. Points are usually sited on level parts of the railway away from bends. The cant is measured using a track gauge with super-elevation gauge fitted (pictured below). The track gauge: The distance between both rails has to be maintained within a pre-determined distance known as the track gauge. This depends on the type of rail installed. The track gauge pictured above also measures this distance. The tolerances are; for flat bottomed VERTICAL rail it is mm, for INCLINED, BULL HEAD & UIC60 rail it is mm. S&T equipment: Conventional fixed Stretchers: Super-elevation gauge The switch rails are independent of one another but are fixed together by stretcher bars. The new type of reinforced stretcher bar is coloured yellow and have the manufacturers name and date marks on them. The points ID number, should always be on the normally closed side and readable from the facing direction. Facing direction (arrowed). Stretcher shoe Insulated swan neck (to stop the track circuit rail voltage shorting). The soleplate. By law all points must have one to hold the gauge at the front. The new yellow stretchers are secured to the rail by stretcher shoes, these are also coloured yellow and are fixed together by using the new type hardlock bolts. The nuts used are male and female and lock together using a torque wrench set to 250Nm.
5 Page 5 of 12 Before yellow stretchers were introduced, they were black and were secured using either square headed black bolts or hexagon black bolts with spring washers. The stretchers and bolts are still widely used on many points, but if a fault (ie crack is detected) they should then be changed to yellow. These type of stretchers are known as fixed, this is because they are drilled and cannot be altered once bolted. The stretchers come in two formats (on plain leads only); these are either long or short. The long ones are only used at the front position (at the toe), and all the rest are the short type. The long stretcher is basically longer because it has what is known as a kicking strap which protrudes through both sides of the points to stop the switch rail from possible lifting although very rare. On switch diamonds (machine operated) the stretchers are the same but use coloured angled shoes (these are used to make sure the stretchers are straight and do not bend because of the extreme angles of the switch rails). On switch diamonds that are operated by clamplocks, the stretchers are installed with the insulation in the middle and also use coloured shoes. On double slip layouts, there are four different coloured shoes used; black, grey, green & red. Switch diamonds with yellow stretchers, coloured shoes (grey & white) and insulations set in the middle. Old style fixed black stretchers using hexagon black bolts (plain lead set shown). Adjustable stretchers: Modern point layouts rebuilt on concrete sleepers will more than likely have adjustable stretchers, these are not fixed and can be adjusted at anytime to alter the FWC or switch openings. The brackets which they are fixed to are totally different to the shoes mentioned above. The stretchers have no swan neck insulations but have rubber insulations at both ends where they are fixed to the brackets. They are held in place by either half-lock nut type nuts or hardlock nuts. Both configurations require different maintenance techniques. Adjustable stretchers can only, at the moment, be fitted to UIC type rail. There are also less fitted; a C type switch UIC54B rail for instance will only have two stretchers fitted as opposed to three on vertical and inclined points. Also modern points are fitted with an additional detector at mid position to double check the points are fitting up along the entire length.
6 Backdrives: Page 6 of 12 FWC on open side RSO on closed side Pictured above is a LH backdrive fitted to a C switch. All Vertical track points over a C switch MUST have a backdrive fitted and all Inclined track points over D switch MUST also have one fitted. The backdrive is used to push up the rear of the points and hold them there by using cranks and rodding. They help maintain the RSO and FWC and prevent FBC. RSO (residual switch opening): the small closed gap that should be between 1.5-2mm. FWC (free-wheel clearance): the other open gap in which the train wheel flange runs through mentioned later. FBC (flange back contact): if the FWC & RSO are incorrect and track gauge is wide, the train wheel may hit the back of the switch rail and cause the stretchers to break. The backdrives come in many many different configurations, they can be fitted to the left, right or in the centre (known as a four foot backdrive), these are used in limited clearance areas where normal (six foot) backdrives cannot be installed, such as stations or cuttings. Backdrives now come as a kit and are installed on plates instead of bolted through the sleeper. The price of a typical kit can start at around The operating equipment: Four foot backdrive Lock fender Pictured above is a HW point machine on points fitted with adjustable stretchers.
7 Page 7 of type detector used to detect points N or R Clamp used to secure points out of use. Above is a mechanically operated set of points by lever in signalbox. HW point machine basic layout: Drive rod, this drives the points normal or reverse. HW1000/2000 machine Lock fender, this connects both switch rails as a connection point for the lock rod. This with the lock rod, locks the points either normal or reverse. The lock rod, connects to the lock blades. Short detection rod. This detects the nearest to machine switch rail. The long detection rod. This detects furthest switch rail from machine. Switch rail bracket, lock arm s are fixed to this. Lock body. Clamplock operated basic plain lead layout: Centre thrust bracket, the hydraulic actuators are fixed here. Brass locking piece. Inside the body, two microswitches copy the fixed and adjustable cams to detect the points closed and locked. Lock arm, this locks the switch blade to the stock rail via brass locking piece. Hydraulic actuators, these drive the points normal or reverse. Adjustable tie-bar, holds drive lock slides together. Drive lock slide, this pushes lock arm in and up to lock switch blade.
The Effects of Track Stability on Point Systems; Page One
The Effects of Track Stability on Point Systems; Page One Voiding Track stability through points is very important, probably the most common cause of point failures is voiding or the effects of voiding.
More informationVarious actuators are now available, the new type have coloured bands signifying what they are, these are as follows:
Page 8 of 12 The detector blades are also fixed to the switch rail brackets, these detect the points locked via an adjustable cam and microswitches housed in the bodies. Another fixed cam on the drive
More informationBackdrive Installation, Set-up & Faults new standard.
Backdrive Installation, Set-up & Faults new standard. A backdrive is only used on vertical switches at type C switch and above or on inclined switches type D and above. It is primarily used to assist the
More informationCONVENTIONAL TURNOUTS
RAILWAY CONVENTIONAL Basic description Turnout mounted in the track enables passing of the vehicle in either straight or branch direction. Depending on the design we distinguish the following types of
More informationBack Drive Equipment List For Full Depth and UIC Rail fitted with Clamplocks or Machines For information only. Not for installation, commissioning,
Back Drive Equipment List For Full Depth and UIC Rail fitted with Clamplocks or Machines For information only. Not for installation, commissioning, testing or maintenance purposes. Always consult NR official
More informationOPERATION & SPARE PARTS MANUAL
P a g e 1 OPERATION & SPARE PARTS MANUAL BACKDRIVE ALIGNMENT KIT (0111/110006) ISSUE 2 JULY 2015 Any alterations or modifications to this equipment or the use of after-market spare parts, without the express
More informationSuspension Supplement Inboard Anti Roll Bar
Suspension Supplement Westfield Sportscars Ltd Unit One Gibbons Industrial Park Dudley Road Kingswinford West Midlands DY6 8XF www.westfield-sportscars.co.uk Tel: +44 (0) 1384 400077 Fax: +44 (0) 1384
More informationARB TACOMA COMBO BULL BAR 2005 ONWARDS. WARNING
ARB TACOMA COMBO BULL BAR 2005 ONWARDS. PART No 323030 Fitting Kit 67963 WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT PROTECTION BAR DOES
More informationWARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.
Part Number: 34000 Product Description: Suited to vehicle/s: ARB WINCH BULL BAR TOYOTA FJ CRUISER WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG: When installed in accordance with these instructions,
More informationWARNING. Part Number: F/KIT: Product Description: JEEP ROCK CRAWLER BAR. Suited to vehicle/s: CHRYSLER WRANGLER JK JEEP 2006 ON
Part Number: 3450210 F/KIT: 6172210 Product Description: JEEP ROCK CRAWLER BAR Suited to vehicle/s: CHRYSLER WRANGLER JK JEEP 2006 ON WARNING This product must be installed exactly as per these instructions
More informationWARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.
Part Number: 36030 Product Description: BULL BAR WINCH TYPE Suited to vehicle/s: CHEVROLET C/K 500-3500 988-998 YEAR MODEL RANGE AND Warn 9,500-5,000lb WINCHES WARNING REGARDING VEHICLES EQUIPPED WITH
More informationTrack Work Information Sheet 2P036 How to change a plain wooden sleeper by hand
Introduction This task covers the replacement of wooden sleepers in all categories of track. It includes the replacement of any chairs, baseplates, clips and pads. For gauge correction see TWI 2G064. Overview
More informationWARNING TAKE NOTE OF THE FOLLOWING: THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING ONLY THE HARDWARE SUPPLIED.
ARB COMBINATION BAR TO SUIT MITSUBISHI PAJERO NM PRODUCT No. 3434050 WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT PROTECTION BAR DOES NOT
More informationSuperbike Kit
Superbike Kit www.spieglerusa.com sales@spieglerusa.com Mounting Instructions & Safety Instructions for Honda CBR 1000 RR ABS model year 2017 - Attention Important Safety Instructions: Thank you for purchasing
More informationInstallation Instructions MX-5 Dual Air Horns
440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com Tools required: Phillips screwdriver, 8mm, 10mm and 21mm sockets, 8mm and 10mm combination wrenches,
More informationInstallation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware
More informationARB WINCH/NON WINCH BUMPER TO SUIT MITSUBISHI PAJERO NM FLARED. EXCLUDING EXCEED MODEL WARNING
ARB WINCH/NON WINCH BUMPER TO SUIT MITSUBISHI PAJERO NM FLARED. EXCLUDING EXCEED MODEL PRODUCT No. 3934020 Sahara Bar 3034020 Sahara Bumper FITTING KIT No. 6171383, 6171762, 6171363 WARNING FOR VEHICLES
More informationA Guide to Key Railroad Terminology for the Northeast Corridor
A Guide to Key Railroad Terminology for the Northeast Corridor Index of terms Approach signal, 8 Diverging route, 5 Ladder, 6 Section break, 12, 13 Tie replacement, 7 Ballast, 3, 4, 7 Double slip switch,
More informationP/N Rev. A. Proximity Sensor Add-On for SMART2 ProTrap on StrapTrap Hoppers
P/N 1123499 Rev. A Proximity Sensor Add-On for SMART2 ProTrap on StrapTrap Hoppers Sensor Add-On S2 ProTrap StrapTrap P/N 1123499 Rev. A 17 14 7 2 6 8 11 Item Part # Description 1. 1123495 Magnet Screw
More informationChevy Nova Pro-Touring Front Suspension Installation Instructions
1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions 1-800-984-6259 www.totalcostinvolved.com 1 Pro-Touring Clip A-Arm Assembly Sway Bar Assembly Fender Panel Kit 8 7/16-20 * 1 ¼
More informationWARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.
Part Number: 3400 Product ARB WINCH BULL BAR Description: Suited to TOYOTA 4 RUNNER YEAR MODELS 03 ON vehicle/s: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG: When installed in accordance with these
More informationDo not have any open flame or heat sources close to the installation
March 6, 2017 IS# 791 Page 1 of 16 Thank you for purchasing a Transfer Flow, Inc. 50-gallon replacement fuel system for your 2011-16 Ford diesel short bed pickup. This system will fit any 2x4 or 4x4 crew
More informationSeries AA Roller Door
Series AA Roller Door Installation Instructions TAUREAN DOOR SYSTEMS Phone (03) 9721-8366 www.taureands.com.au Extreme safety warning. Safe practices must be observed when working at heights, lifting roller
More informationRAIL MATERIAL HANDLING TONGS RAIL IPS 40 TONGS FROG LIFTING IPS 43
INDEX 40 51 TONGS RAIL IPS 40 THREADING TONGS & SPREADER BARS RAIL IPS 42 TONGS FROG LIFTING IPS 43 TONGS SLEEPER/TIMBER IPS 44 PULLER & TUGGER RAIL IPS 45 THREADER BALL & RAIL IPS 46 RUNNER & THREADER
More informationCHRYSLER WRANGLER JK JEEP 2006 ON WARNING. ARB 4x4 ACCESSORIES. Corporate Head Office
Part Number: 3450210 F/KIT: 6172210 Product Description: JEEP ROCK CRAWLER BAR Suited to vehicle/s: CHRYSLER WRANGLER JK JEEP 2006 ON WARNING This product must be installed exactly as per these instructions
More information3 Axles and brakes. 3.1 Function and construction of the axles Construction Function
3 Axles and brakes 3.1 Function and construction of the axles 3.1.1 Function Each wheel has an independent suspension system in the axle body (1), so that individual wheel suspension is provided. The swinging
More informationBolt FBN The heavyweight.
120 The heavyweight. OVERVIEW II, A4, stainless steel A4 Approved for: Non-cracked concrete C20/25 to C50/60 Also suitable for: Concrete C12/15 Natural stone with dense structure -GS (with large washer),
More informationCOMBAR G/BAR CHEROKEE KJ SRS NFO
Part Number: 3450170 F/KIT: 6173661 & 6173668 Product Description: Suited to vehicle/s: Optional Fitting Kit: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG; When installed in accordance with these
More informationProfile series I-40. System kit Profile series I-40
Profile series I-40 System kit Profile series I-40 n n n a n n n R n a R 45 Profile series I-40 Contents 1 Technical data/profile machining F f Page 1 2 Page 1 3 Page 1 5 Page 1 8 Profiles Page 2 2 3000
More informationINSTALLING THE NEUTRAL SAFETY SWITCH WIRES
Installation Instructions Magnum Grip Pro Bandit Shifter Part Number 81045 & 81046 2004, 2003 by B&M Racing and Performance Products (Visit www.bmracing.com for additional products and product information)
More informationSPIRIT - FRAME ASSEMBLY
Titel - 1 - Titel - 2 - Table Of Contents QUICKIE SPIRIT... 4 FRAME... 4 SPIRIT - FRAME ASSEMBLY... 4 SEATING... 6 SPIRIT - STD SEAT AND BACKREST... 6 SPIRIT - UNISUN BACKREST- DISCONTINUED... 8 HANGERS
More informationMAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS
MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent
More information1.0 Scope: Adjustment of headheight for PW2000 for printing on 0,2 0,3mm plates especially Halm.
Approval: TNI (Init.) Version: C Page 1 of 6 1.0 Scope: for printing on 0,2 0,3mm plates especially Halm. 2.0 Extent and limitation: After adjusting the headheight it is necessary to perform a bidirectional
More informationPart number SP Acura RSX Type-S
Part number SP1477 02-06 Acura RSX Type-S 1- cold air intake system 1-3 Injen filter (#1014) 1-2 7/8 x 3 60 deg. elbow (#3007) 1-1525 sensor grommet (#6014) 1-20 - 8mm vacuum hose (#3091) 1-18 - 17mm vacuum
More informationINSTALLATION INSTRUCTION
1551 S. Vineyard Avenue Ontario, CA 91761 (909) 923-1973 INSTALLATION INSTRUCTION Club Car Precedent Installation Notes CURTIS 1234, 1236 OR 1238 AC INDUCTION MOTOR/ CONTROLLER REVISION: B This kit is
More informationRAIL MATERIAL HANDLING TONGS RAIL IPS 40 TONGS FROG LIFTING IPS 43
INDEX 40 51 TONGS RAIL IPS 40 THREADING TONGS & SPREADER BARS RAIL IPS 42 TONGS FROG LIFTING IPS 43 TONGS SLEEPER/TIMBER IPS 44 PULLER & TUGGER RAIL IPS 45 THREADER BALL & RAIL IPS 46 RUNNER & THREADER
More informationTransportation Engineering II UNIT - I
Transportation Engineering II UNIT - I I. Components of a Permanent Way: A. Rails: Rails are the I-section members of a track laid in two parallel lines to provide a level surface for the movement of trains.
More informationINSTALLATION INSTRUCTIONS 97 FORD EXPEDITION
INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before
More informationInstallation Instructions for TLC79DCA Toyota Landcruiser VDJ79 Series 90lt Auxiliary Tank
Installation Instructions for TLC79DCA Toyota Landcruiser VDJ79 Series 90lt Auxiliary Tank 1. Carry out wiring of PG200 switch gauge unit, suggested switch location is in the large rectangle blank on the
More informationMC2 BOWLING Pin-Setter
MC2 BOWLING Pin-Setter File No.: M200509-01 COPYRIGHT 2005, VIA BOWLING PRODUCTS Content I. Installation of Front-End Assembly --------------------------------------- 1 II. Installation of Back-End Assembly
More informationINSTALLATION AND OPERATING INSTRUCTIONS
ASTRO ENVELOPE FEEDER AMC-2000 INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION Thank you for purchasing the Astro Envelope Feeder. It is fast, efficient, reliable, and designed to provide many years
More informationACCESS SOLUTIONS NEW PRODUCTS BROCHURE.
ACCESS SOLUTIONS NEW PRODUCTS BROCHURE www.essentraaccesssolutions.com ESSENTIAL SOLUTIONS DELIVERED NEW PRODUCTS Locks Hinges Gaskets Handles Stainless Steel Products Electronic p3-6 p13 14 p17-18 p7-8
More informationARB PRADO WINCH/NON WINCH BUMPER TO SUIT GXL, VX AND GRANDE 2003 ONWARDS.
ARB PRADO WINCH/NON WINCH BUMPER TO SUIT GXL, VX AND GRANDE 003 ONWARDS. PART No 390 500050 Top Tube Kit 50073 Buffer Kit With hole (required when fitting Top Tube) 50074 Buffer Kit With no hole FITTING
More informationSeries B Roller Door. Installation Instructions. TAUREAN DOOR SYSTEMS Phone (03)
Series B Roller Door Installation Instructions TAUREAN DOOR SYSTEMS Phone (03) 9721-8366 www.taureands.com.au Extreme safety warning. Safe practices must be observed when working at heights, lifting roller
More informationBallast Usually stone chippings, or similar material, which support the sleepers and hold them in place on the ground.
Model Rail Terminology Alternating Current/AC The electric current that flows alternately through each wire in a rapid sequence called a cycle. The normal mains electricity supply is powered by Alternating
More informationPRODUCT SAFETY NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationRemoving and installing cylinder head Removing, installing and tensioning toothed belt
Page 1 of 10 Removing and installing cylinder head Removing, installing and tensioning toothed belt Special tools, workshop equipment, test and measuring appliances and auxiliary items required 3359 Locking
More informationMain Frame (1,676 MM (5-1/2 FT.) Hay Pickup)
Main Frame (,676 MM (5-/2 FT.) Hay Pickup) 2 E34250 STRIPPER 2-3000 AUGER E66297 ANGLE 2 300- AUGER, (SUB FOR E34496) (SUB E9572) E9572 ANGLE 2 AUGER E6905 TUBE 59400-86 Pickup Heads Strippers (,676 MM
More informationFRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
More informationCOOPERATIVE PATENT CLASSIFICATION
CPC E COOPERATIVE PATENT CLASSIFICATION FIXED CONSTRUCTIONS BUILDING E01 CONSTRUCTION OF ROADS, RAILWAYS, OR BRIDGES (of tunnels E21D) PERMANENT WAY; PERMANENT-WAY TOOLS; MACHINES FOR MAKING RAILWAYS OF
More informationIndexing Plunger 417. Triangular Knobs, Made from Plastic. Triangular Knobs, Made from Stainless Steel
Standard Parts for Operating - Overview Cam-Action Indexing Plungers / Indexing Plungers Cam-Action Indexing Plunger 612, Made from Steel and Stainless Steel Page 532 Page 533 Indexing Plunger 417 Indexing
More informationWARNING TAKE NOTE OF THE FOLLOWING: THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING ONLY THE HARDWARE SUPPLIED.
ARB WINCH/NONWINCH BUMPER TO SUIT TOYOTA HJ100 IFS PRODUCT No. 3913140 5100050 Top Tube Kit 5100160 Buffer Kit With hole (required when fitting Top Tube) 5100170 Buffer Kit With no hole Fitting Kit No.
More informationProduct Deluxe Combination Winch and Non Winch Bull Bar, Flare and Non Flare Description: Suited to Nissan D40T Navara XC DC SC 2008 ON WARNING
Part Number: 343840 & 343850 F/Kit 617501 Product Deluxe Combination Winch and Non Winch Bull Bar, Flare and Non Flare Description: Suited to Nissan D40T Navara XC DC SC 008 ON vehicle/s: WARNING REGARDING
More informationBIG DEAL. cylinders are still a. compact air. inside: Digital Ebook A Design World Resource. Compact Air Cylinders: 101
compact air cylinders are still a BIG DEAL inside: 2 Compact Air Cylinders: 101 5 9 Enormous range of options Applications 10 Custom Compact Air Cylinders And more! Digital Ebook A Design World Resource
More informationService Manual. LT-5 Lawn Tractor
Service Manual LT-5 Lawn Tractor NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power equipment of the kind described in this publication,
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1963-67 Corvette P/N: 121620 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More information21" STEEL DECK WALK BEHIND COMMERCIAL MOWERS SERIES 19
Parts Manual for 21" STEEL DECK WALK BEHIND COMMERCIAL MOWERS SERIES 19 MODEL CP215519HV CP216019KWV CRP216019KWV McDonough, GA, 30253 U.S.A. COPYRIGHT 2006 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED.
More informationParts & Owner s Manual
Havener Enterprises, Inc. 368 S. Michigan Ave. Bradley, IL 60915 815.935.8383 32, 36, 48 & 52 Commercial Belt-Drive Mowers Parts & Owner s Manual Congratulations on the purchase of your new Bradley mower.
More informationKJ JEEP COMBINATION BULL BAR WARNING
KJ JEEP COMBINATION BULL BAR PRODUCT NUMBER FITTING KIT NUMBER 3450120 6171962 WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT PROTECTION BAR
More informationPRODUCT SAFETY NOTICE DEALER/INSTALLER NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationUSE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:
1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE
More informationINSTALLATION AND OPERATING INSTRUCTIONS
ASTRO ENVELOPE FEEDER AMC-2000-5 FOR RYOBI 3302 / ITEK 3985 (2 COLOR) INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION Thank you for purchasing the Astro Envelope Feeder. It is fast, efficient, reliable,
More informationCOMPACT DEMO RULES 2016
COMPACT DEMO RULES 2016 ENTRIES 1. NO ALCOHOL PERMITTED. STATE LAW ALSO PROHIBITS THE CONSUMPTION OF ALCOHOLIC BEVERAGES WHILE OPERATING A VEHICLE. THEREFORE, NO DRIVER UNDER THE INFLUENCE OF ALCOHOL OR
More informationFLANGE. Flanges used for
FLANGE FLANGE Flanges with rating class designations 150, 300, 400, 600, 900, 1500, and 2500 in sizes NPS 1 2 through NPS 24 ASME B16.5: Pipe Flanges and Flanged Fittings (NPS 24 ) ASME B16.47: NPS 26
More informationOWNER'S MANUAL MOBILE LIFT:
: 18"MODELS-(19675 & 24565) OR 24" MODELS-(20565, 24570, & 24770) INSTALLATION AND OPERATION INSTRUCTIONS -SERVICE AND PARTS INFORMATION IMPORTANT A class III frame receiver hitch must be installed by
More informationCustomers please note that ALL Stock Points are manufactured for use with GRS or Tenmille ground throw levers! (as picture above). The picture above i
January 2015 All content & images copyright of Garden Railways Specialists Ltd Customers please note that ALL Stock Points are manufactured for use with GRS or Tenmille ground throw levers! (as picture
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More information2008 K&M NEWSPAPER SERVICES, INC SLS.1000 HOPPER SLS1000 HOPPER
SLS1000 HOPPER - 1-800-828-0242 NEEDLE ASSEMBLY - 2-800-828-0242 NEEDLE ASSEMBLY ITEM PART NUMBER DESCRIPTION QUANTITY 1 KMS 5020 ROD END 1 2 KMS 2093 NEEDLE BAR ARM 1 3 KMS 2045 NEEDLE BAR LINK 1 4 KMS
More informationAssembly & Installation Instructions
TM P R O D U C T S Assembly & Installation Instructions FOR 28 SERIES SNOWPLOW PIVOT ASSEMBLY AND FLOAT LIMITER 99103000 FOR SERIAL NUMBERS 28D100000 TO 28D100770 97100552A 1. THINK SAFETY, ALWAYS WEAR
More informationInstallation Instructions: RB26 WET AND DRY SUMP ENGINE CRADLE
Installation Instructions: RB26 WET AND DRY SUMP ENGINE CRADLE Congratulations on the purchase of your RB26 Platinum Racing Engine Cradle (PREC)! This PREC will assist in preventing block twist, block
More informationLast Revision: 30JN THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 30JN2007 1969 THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationWARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.
Part Number: 343870 F/Kit 17557 Product Deluxe Combination Winch and Non Winch Bull Bar Description: Suited to Nissan XTERRA 05ON USA Only vehicle/s: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG;
More informationPROSTOCK CLASS. Infraction of rules will be decided by Race Officials. Number Plate
PROSTOCK CLASS Tech Rules: Must have race receiver and needs to work (cruiser class: both driver & passenger must be able to hear) All four brakes must lock up or won t race. You will load up and go home
More information1/35 Caterpillar Sixty Conversion Set
1/35 Caterpillar Sixty Conversion Set No.35506 WWW.LZmodels.com Made in EU contains 1 highly detailed and accurate set Conversion set for Trumpeter s Russian S-65 Stalinetz tractor 70+ resin parts 40+
More informationMfg. No: P216020KWV, 21" 6 TP Steel Deck Series
Parts Manual Mfg. No: 7800557 P216020KWV, 21" 6 TP Steel Deck Series Copyright Briggs and Stratton. All Rights reserved 28-Sep-2018 Model Components Table Of Contents Page Accessory Recycling Kits..............................................................................
More informationThe specialist for fastening technology. Post holders NEW. to our product range
Post holders H post anchors H post anchors Fork width Dimensions a) Drill holes b) Art. no. (mm) Overall/Post support (mm) Post support (mm) PU 904722 91 600 x 60 / 300 4 x 11 904723 101 600 x 60 / 300
More informationDODGE DAKOTA 3 BODY LIFT INSTALLATION INSTRUCTIONS KIT # 60153
DODGE DAKOTA 3 BODY LIFT INSTALLATION INSTRUCTIONS 2003-04 KIT # 60153 Installation of a Performance Automotive Group body lift kit will change the vehicle s center of gravity and handling characteristics
More informationMaterial: Hinge Parts: zinc die, matt chrome plated, or zinc die, matt black. Pin: stainless steel Nut plate: steel, zinc plated
4-249 Hinge Pr01 180 Small elegant hinge. 180 Opening. Adjustments are possible with respective bores provided. The nut plate can be mounted in different ways, according to the application. zinc die, matt
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More informationS840, S845, S846 Series Single-break changeover, NC or NO contacts, positive opening operation and wiping action Catalogue D40.en
Snap-action switches S80, S85, S86 Series Single-break changeover, NC or NO contacts, positive opening operation and wiping action Catalogue D0.en Snap-action switches, S80, S85, S86 Series Single-break
More informationInstallation Manual. stairlift. A 4724 Neukirchen/W, Salling 8 Tel: 07278/ , Fax: 07278/ Mobil: 0664/
Installation Manual Ω MEGA stairlift A 4724 Neukirchen/W, Salling 8 Tel: 07278/3514-15, Fax: 07278/3514-12 Email: office.lehner@gmx.at Mobil: 0664/1612980 CONTENTS OBSERVE THE FOLLOWING POINTS BEFORE INSTALLATION!...
More informationItem No. Part Number Description Qty
36 Frame Assembly 1 336-001 Hood 36" 1 2 100-009 Saucer Nut 4 3 300-001 Rear Deck Weldment 1 4 200-006 Nylon Nut M10 GB889-86 9 5 200-003 Hexagon Bolt M10*25 GB5783-86 12 6 100-007 Chute Deflector 1 7
More informationASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH
ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate procedures in this Manual to end user. (3) Have end user
More informationSECTION 7: PARTS LIST FOR MODEL 5KL
SECTION 7: PARTS LIST FOR MODEL 5KL 3 9 4 5 6 7 0 4 3 5 3 34 9 8 5 6 7 8 3 30 3 4 5 0 9 8 6 7 5 7 68 40 5 5 7 39 36 53 60 58 54 57 58 59 48 50 49 45 46 4 44 4 6 35 6 65 63 64 66 67 47 0 Model 5KL. 73-0447A
More informationRAS-5E PART NO Date: 04/08/02
33-400, 33-401, 33-402, 33-403 14 RADIAL SAWS 33-410, 33-411, 33-412, 33-413 16 RADIAL SAWS 33-420, 33-421, 33-422, 33-423 18 RADIAL SAWS RAS-5E PART NO. 424-03-651-0018 Date: 04/08/02 Page1/ RAS-5E /DEB
More informationEM 27 2UZ-FE ENGINE MECHANICAL CAMSHAFT REMOVAL
2UZ-F NGIN MCHANICAL CAMSHAFT M 27 RMOVAL 1. RMOV TIMING BLT (See page M-18) 2. RMOV IGNITION COIL ASSMBLY (a) Disconnect the 4 ignition coil connectors. (b) Remove the 4 bolts and 4 ignition coils. 3.
More informationFrom a modest beginning in 1976 producing small. quantities of gravity conveyor rollers, Arnott Handling
ARNOTT HANDLING LTD From a modest beginning in 1976 producing small quantities of gravity conveyor rollers, Arnott Handling Equipment Limited has grown to become one of the United Kingdom s foremost manufacturers
More informationTools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40
Subaru 2004+ Legacy GT & Outback XT For JDM 2.0 twinscroll turbo and USDM 2.5 turbo models Front Mount Intercooler Fitting Instructions PN# LEG-1348-000 You are now the proud owner of a highly tested and
More informationAR46.20-P-0601P Setting play between thrust element and steering rack MODEL 203, 209, 211, 215, 220
AR46.20-P-0601P Setting play between thrust element and steering rack 4.5.07 1 Stop plate 2 Adjusting screw 3 Thrust piece 4 Rack 2 Adjusting screw P46.20-2178-09 14 housing 16 Stop ring P46.20-2181-01
More informationSUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1
SUENSION SUENSION SYSTEM 1 Vehicle/pulls Bottoming Sway/pitches Wheel shimmy Abnormal tire wear SUENSION SYSTEM PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of the problem. The
More informationWARNING. ARB 4x4 ACCESSORIES. Corporate Head Office Garden St Tel: +61 (3) Kilsyth, Victoria Fax: +61 (3) AUSTRALIA 3137
Part Number: 3948020 Product Description: Suited to vehicle/s: Optional Fitting Kit: SAHARA BAR ISUZU DMAX 5148020 Sahara Top Tube Kit 3540050 Winch Install Kit 3500640 ARB AUX Fog Light Adaptor 3500530
More information1. General Description
General Description 1. General Description A: SPECIFICATION Front Rear Model Wheel arch height (Tolerance: +12 mm 24 mm ( +0.47 in 0.94 in)) mm (in) 376 (14.8) Camber (Tolerance: 0 45 Differences between
More informationHusqvarna Hedgetrimmers 325HS/ 325HE/ 325HDA. Workshop manual
Husqvarna Hedgetrimmers 325HS/ 325HE/ 325HDA Workshop manual 101 90 73-26 2 Workshop Manual Hedge trimmers Supplement for models 325HS, 325HE,325HDA Contents 1. Starter 5 2. Ignition system 7 3. Fuel system
More informationChevrolet 3100 IFS Kit
1947-54 Chevrolet 3100 IFS Kit Congratulations on your purchase on what we believe is the finest IFS kit available for 1947-54 Chevrolet pickups with stock frames. We have invested many hours into designing
More informationIllustrated Parts List
Illustrated Parts List Hydrostatic Lawn Tractor IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and
More information95-98 CHEVY TRUCK INSTALLATION INSTRUCTIONS KIT #112 #113
This body lift kit should only be installed on vehicles that are in good working condition. Before the installation begins, the vehicle should be thoroughly inspected for evidence of corrosion or deformation
More informationI. Before starting installation
5. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. A. Disconnect battery cables 1. Disconnect the negative cable first, then the
More informationT15 Fleet Frontal Protection System Vehicle: Mazda BT50 09/08+ Part No. 070SB15X46Z
Australian Standards Relating to Installing Vehicle Frontal Protection Systems (VFPS): AS 4876.1-2002 a) Do not attach V.F.P.S. to vehicle using anchorages not intended for this purpose (e.g. engine mounting
More informationSub Section Title Page No.
Sub Section Title Page No. 1 Introduction 3 2 Routine Maintenance 3 3 Disassembly 4 3.1 Disassembly of Double Crank Design 4 3.2 Disassembly of Scotch Yoke Design 5 3.3 Disassembly of Actuator Cylinder
More informationPassenger Car Trucks... Components and Maintenance - Part 1
Passenger Car Trucks... Components and Maintenance - Part 1 By Martin McDonnough This is the second in a series of highly informative articles by veteran Boston Amtrak car inspector Martin McDonough, a
More information