0 Series. 9Exit Device

Transcription

1 0 Series 9Exit Device Copyright , Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

2 Table of Contents Features, Applications and UL Fire Door Ratings Series Rim Exit Device Functions and Trims Series Surface Vertical Rod Exit Device Functions and Trims Series Mortise Lock Exit Device Functions and Trims Series Narrow Stile Concealed Vertical Rod Exit Device Reversible Rim Exit and Trim for the 9898 Rim Exit Device ET Trim, Levers and Pulls Studio Collection Levers Ordering Gramercy Series Levers Coastal Series Levers and Thumb Piece Pulls Electromechanical Functions and Accessories Mullions: Aluminum, Steel and Electrified Mullion Accessories, Stabilizers and Door Coordinators Mechanical Options and Descriptions Cylinder Options and Descriptions How to Order Finishes and Finish Care MicroShield As part of their promise to provide innovative solutions to their customers, certain ASSA ABLOY Group brands offer the MicroShield technology, a silver-based antimicrobial coating designed to inhibit the growth of bacteria. MicroShield is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. MicroShield Coating Revolutionary finish coating available on all SARGENT product lines, utilizes a silver-based antimicrobial compound from Agion Technologies As an integral part of the finish coating, MicroShield lasts for the life of the hardware MicroShield coating permanently suppresses the growth of bacteria, algae, fungus, mold and mildew. It is effective against a broad spectrum of bacteria. Non-toxic and completely safe. The Agion antimicrobial compound is EPA and NSF approved and FDA listed for use in medical and food preparation equipment. Applications: Anywhere there is need for a clean environment (hospitals, laboratories, schools, medical centers, daycare, food processing etc.)

3 Features, Applications and UL Fire Door Ratings Features Full line of exit devices offering a selection of both wide and narrow stile exit devices, including concealed and surface vertical rods, rim and mortise Maximum 4-1/2" (114mm) projection, minimum 2-3/4" (70mm) dogged All Sargent exit devices can be masterkeyed or grand masterkeyed with any other Sargent product All crossbar assemblies are brass, bronze, stainless steel, or steel (see specific device) Stainless steel springs throughout Trim is through-bolted All exit devices meet ANSI standard 156.3, Grade 1 UL Listed UL Listed to Canadian safety standards All fire exit hardware for hollow metal door applications listed up to 3 hours (A label) (Double doors require astragal) All fire exit hardware for wood door applications listed up to 1-1/2 hour (B label) except where noted Applications Single Door Rim Type 9800 Surface application. Pairs of Doors with 980 Mullion Rim Type Each 980 Mullion - 1 Each Two independent active doors with full double door opening when required. Pairs of Doors without Mullion Surface Vertical Rod Type 9700 or Concealed Vertical Rod Type Each 2 point locking both doors. Each door active. Do not use an overlapping astragal. Pairs of Doors without Mullion Vertical Rod Type Each Rim Type Each Both devices are surface applied. A coordinator is recommended. = Available Application Type Of Device Series Device Single Doors Pair of Doors Swinging in the same direction Double Egress Pair of Doors Swinging in opposite directions Mortise Rim ** Concealed Mortise and Surface Vertical Rod Two Rim With Mullion ( available) *Two Surface Vertical Rod No astragal No coordinator Two Concealed Vertical Rod No overlapping astragal *Two Surface Vertical Rod *Two Concealed Vertical Rod X X X X X Maximum Door Opening UL Fire Door Rating (A) (B) (C) (D) (E) 3 1-1/2 3/4 1-1/2 3/4 Hour Hour Hour Hour Hour 4'0" X 10'0" (1219 X 3048) 4'0" X 8'0" (1219 X 2438) 4'0" x 7'2" (1219 X 2184) 8'0" X 8'0" (2438 X 2438) 8'0" X 8'0" (2438 X 2438) 8'0" X 8'0" (2438 X 2438) 8'0"x 7'2" (2438 X 2184) 8'0" X 8'0" (2438 X 2438) 8'0" x 7'2" (2438 X 2184) * Limited for Fire Doors listed by UL for this use. NFPA requires an astragal on 3 hour applications ** 75 and 76 functions are not available with 12- fire rated 9800 devices Vertical rod applications will not work with astragal Note: Please contact door manufacturer for specifications regarding fire door construction Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and Sargent Manufacturing Company makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings. 3

4 9800 Series Rim Exit Device 9800 Rim Exit Device The 9800 Series exit devices are ordered with trim and shipped complete with the strike, screw packs and cylinder as required in one carton. The cross bars are cut to the correct length, based on door width. Specifications For Doors Mounting Chassis Cover Chassis Crossbar Hand Dogging Strike Fire Exit Hardware See chart page 3 Alternate Strikes for Rim Devices /8" (16mm) 4 3-5/8" (92mm) Wood or metal. 1-3/4" (44.5mm) thick standard. 2-1/4" (57mm) thick on order. Other door thickness, consult factory. 4-1/8" (105mm) minimum stile Supplied standard with wood and machine screws. Through-bolts available on order Brass, bronze or stainless steel Nonferrous alloy 1" brass, bronze and stainless steel tubing. Specify 42- for reinforced cross bar Reversible Standard Allen key dogging 649 standard strike for panic and fire 613 Half mortised Nylon coating on face plate only Specify hardware finish 3-5/8" (92mm) L 1-1/2" 1-1/2" (38mm) 1-1/2" 1/4" (38mm) (6mm) 642 Full mortised Dimension L equals door thickness plus 1/2" Nylon coating on lip only Specify hardware finish 649 Strike 1-5/32" (29mm) For 9800 and Supplied standard Surface applied Black nylon coated 2" (51mm) 3-11/16" (94mm) 7/16" (38mm) 2-7/16" (63mm) 3/4" (19mm) 644 Surface applied For use on pairs of doors without mullion Black nylon coated

5 9800 Functions and Trims How to order: 700 Series ET Trim Exits with ET Trim, specify lever design after the ET designation (e.g., ETL) Lever Designs for ET Controls A, B, E, F, J, L, P, W Also available with Coastal Series & Studio Collection Levers Note: Voltage must be specified for 73, 74, 75 & 76 function ET trims (12v or 24v) PRK Knob Trim RK Trim with K knob is through-bolted to the chassis. To order: PRK trim less exit device, Specify: 814-PRK for 04 function Specify: 810-PRK for 10 function Specify: 813-PRK for 13 function Specify: 825-PRK for 15 function Pull & Thumb Piece Trim Section SARGENT Function Numbers ANSI Function Numbers Options Series Function Trim Hand O/S Finish I/S Finish Door Width 10-SG ETL RHR 26D 32D 36" SARGENT Function Numbers Description & Cylinder Info. (1-3/4" Door) Night Latch Key Retracts Latch #34 Cylinder Supplied Description & Cylinder Info (1-3/4" Door) Night Latch Key Retracts Latch #34 Cylinder Supplied ANSI Type Panic & Fire Note: Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32 or 32D to match accordingly. For nickel finishes, specify 14/32 or 15/32D to receive nickel finished trims and stainless exit devices 814-FLL 814-FLW 814-MAL 814-PTB 814-STS No O/S Operation or Cylinder (Pull Only) 810-FLL 810-FLW 810-MAL 810-PTB 810-STS Passage Only (No cylinder) 828-FLL 828-FLW 828-MAL 828-PTB 828-STS Key Outside Unlocks/ Locks Trim #34 Cylinder Supplied ANSI Function Numbers Night Latch Key Retracts Latch #34 Rim Cylinder Supplied No outside Operation PRK used as a Pull only Classroom Key Outside Unlocks/locks Trim #34 Rim Cylinder Supplied Trim Designations Use three letter designations (Ex PTB ) when ordering the exit device with trim Use the six digit designation (Ex 866-MAL ) when ordering trim without an exit device, always specify finish 866-FLL 866-FLW 866-MAL 866-PTB 866-STS 862 Pull 862 Pull N/A N/A 9804 x PRK 9810 x PRK 9813 x PRK Passage Only (No cylinder) 9815 x PRK Note: Thumb piece trims for 63 and 66 function devices are identical and are identified as 66 function when trim is ordered separately Note: FLW trim is not available in 32(629) or 32D(630) 9804 x ET_ No outside Operation (No Cylinder) 9810 No outside Operation (No Cylinder) ET Control is used as Pull Only 9810 x ET_ Key Outside Unlocks/locks Trim #41 Cylinder Supplied 9813 x ET_ Passage Only (No cylinder) 9815 x ET_ Electrified ET Trim - Fail Safe 73 Power Off, Unlocks Lever (No Cylinder) 9873 x ET_ Electrified ET Trim - Fail Secure 74 Power Off, Locks Lever (No Cylinder) 9874 x ET_ Electrified ET Trim - Fail Safe Power Off, Unlocks Lever, Key Retracts Latch 75++ #34 Cylinder Supplied 9875 x ET_ NOT available with devices 76** Electrified ET Trim - Fail Secure Power Off, Locks Lever, Key Retracts Latch #34 Cylinder Supplied NOT available with devices 9876 x ET_ Series 9800 Panic & Fire 9804 x Trim Designation 9810 x Trim Designation 9828 x Trim Designation 9863 x Trim Designation Options 9800 Mechanical Options: CPC- *** SG- TB- Cylinder Options: P P P P P- 73-7P F F BR- LC- SC- SE- *** Only available with 15, 26D, and 32D finishes Available Finishes SARGENT Finishes B 10BE 10BL D 26 26D 32 32D BSP 5 BHMA Finishes E

6 9700 Series Surface Vertical Rod Exit Device 9700 Series Surface Vertical Rod Exit Device 9700 SVR Exit Device The 9700 Series exit devices are ordered with trim and shipped complete with the strikes, screw packs and cylinder as required in one carton. The cross bars are cut to the correct door width and vertical rods are made to order, based on mounting position of the hardware and opening height. 646 Top Strike Standard Top Strike for both Panic & Fire (12-) Hardware Surface applied to frame Black nylon coated Replaces 629 Strike 1-5/32" (29mm) 3/4" (19mm) 1/4" (6mm) 3-11/16" (94mm) Features Two point latching (top and bottom of the door) Top & bottom latchbolt projection adjustable through center case Standard bottom latch compatible with latchtrack thresholds (by others) Single and double door applications Devices are ANSI A Grade 1 UL Fire and Panic listed Rods are 1/2" (13mm) brass, bronze or stainless steel 624 Bottom Strike Standard for 9700 Applied to surface of floor or to a flat threshold Black nylon coated 2-1/2" (64mm) Specifications for 9700 Series Exit For Doors Wood or metal. 1-3/4" (44.5mm) thick standard. 2-1/4" (57mm) thick on order. Other door thickness, consult factory. 3" (76mm) minimum stile. Maximum door height 96" Mounting Supplied standard with wood and machine screws. Through-bolts available on order Chassis Cover Brass, bronze or stainless steel Chassis Nonferrous alloy Crossbar 1" brass, bronze and stainless steel tubing. Specify 42- for reinforced cross bar Hand Non Handed Dogging Standard Allen key dogging Strikes 646 top strike for panic & fire and 624 bottom strike for panic & 655 bottom strike for fire Rod 1/2" brass, bronze or stainless steel Fire Exit Hardware See chart page 3 Opening Height 84" (2134mm) Standard Inside Lever Assembly for 300 Series Aux Control 6 Attaches to top rod and engages with 300 Series Auxiliary Control. Packed standard with 306 and 313 Auxiliary Controls Part # Bottom Strike 648 & 653 Strikes (Alternate Strikes for 9700 SVR Devices) 648 Strike For doors having transom panel applications Black nylon coated 1-1/8" (29mm) 7/16" (11mm) 2-1/2" (64mm) 1 7/8" (48mm) 9/16" (14mm) 3/8" (10mm) Standard bottom strike for and Stainless steel Black nylon coated Replaces 647 Strike 653 Strike 2-3/4" (70mm) Alternate for /4" (44mm) 2-1/8" 2-3/4" (54mm) (70mm) 1- (46mm) 2-5/16" (59mm) Black nylon coated 1/2" (13mm)

7 9700 Functions and Trims How to order: Options Series Function Trim Hand O/S Finish I/S Finish Door Width Door Height AFF ETL RHR 15 32D 36" 84" 36" 700 Series ET Trim Exits with ET Trim, specify lever design after the ET designation (e.g., ETL) Lever Designs for ET Controls A, B, E, F, J, L, P, W Also available with Coastal Series & Studio Collection Levers Note: Voltage must be specified for 73 & 74 function ET trims (12v or 24v) PRK Knob Trim PRK Trim with K knob is through-bolted to the chassis. To order: PRK trim less exit device, Specify: 813-PRK for 06 function Specify: 810-PRK for 10 function Specify: 813-PRK for 13 function Specify: 825-PRK for 15 function 300 Series++ Auxiliary Control 300 Series Auxiliary Control SARGENT Function Numbers ANSI Function Numbers SARGENT Function Numbers Description & Cylinder Info. (1-3/4" Door) Description & Cylinder Info. (1-3/4" Door) Key unlocks Trim, Trim retracts latch/ Trim relocks when key is removed #41 Cylinder Supplied Description & Cylinder Info. (1-3/4" Door) ANSI Type Panic & Fire 9706 x ET_ No outside Operation (No Cylinder)** No outside Operation (No Cylinder)** ET Control is used as Pull Only 9710 x ET_ Key Outside Unlocks/locks Trim #41 Cylinder Supplied 9713 x ET_ Passage Only (No cylinder) 9715 x ET_ 73 ANSI Function Numbers Electrified ET Trim - Fail Safe Power Off, Unlocks Lever (No Cylinder)** 9773 x ET_ Electrified ET Trim - Fail Secure 74 Power Off, Locks Lever (No Cylinder)** 9774 x ET_ Note: Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32 or 32D to match accordingly. For nickel finishes, specify 14/32 or 15/32D to receive nickel finished trims and stainless exit devices Note: AFF means Above Finished Floor, center line of rail Above Finished Floor ** Cylinder Override is available with a 306 Aux Control Example Order: 9773F 12V x ETMG x 306 x RHR x 32D 36"w x 84"H SARGENT Function Numbers Key unlocks Trim, Trim retracts latch/ Trim relocks when key is removed #34 Rim Cylinder Supplied No outside Operation PRK used as a Pull only Classroom Key Outside Unlocks/locks Trim #34 Rim Cylinder Supplied Key unlocks Turn; Turn retracts latch/ Turn relocks when key is removed #41 Cylinder Supplied Pull Only (No Cylinder)*** 810-FLL 810-FLW 810-MAL 810-PTB 810-STS Passage Only (No cylinder) 828-FLL 828-FLW 828-MAL 828-PTB 828-STS Key Outside Unlocks/ locks Trim #34 Cylinder Supplied 866-FLL 866-FLW 866-MAL 866-PTB 866-STS 9700 Panic & Fire 9710 x 306 Key Outside Unlocks/locks Turn #41 Cylinder Supplied 9710 x 313 Note: When ordering 9700 Series Exit Device x 300 Series Aux. Control, specify 10 Function for the exit. Example: 9710F x 306 x RHR x 32D x 42" x 90" ++ Note: Exit Devices must be mounted 38" AFF when used with a 300 Series Auxiliary Controls to meet ICC/ANSI A Accessible & Usable Buildings and Facilities Code Pull & Thumb Piece Trim Section Trim Designations Series Use three letter designations (Ex PTB ) when ordering the exit device with trim Use the six digit designation (Ex 866-MAL ) when ordering trim without an exit device, always specify finish *** Cylinder Override is available with a 306 Aux Control Note: Thumb piece trims for 63 and 66 function devices are identical and are identified as 66 function when trim is ordered separately Note: FLW trim is not available in 32(629) or 32D(630) 9706 x PRK 9710 x PRK 9713 x PRK Passage Only (No cylinder) 9715 x PRK ANSI Function Numbers 9700 Panic & Fire 9710 x Trim Designation 9728 x Trim Designation 9763 x Trim Designation Options 9700 Mechanical Options: CPC- *** SG- TB- Cylinder Options: P P P P P- 73-7P F F BR- LC- SC- SE- *** Only available with 15, 26D, and 32D finishes Available Finishes SARGENT Finishes B 10BE 10BL D 26 26D 32 32D BSP 7 BHMA Finishes E

8 9900 Series Mortise Lock Exit Device 9900 Mortise Lock Exit Device The 9900 Series exit devices are ordered with trim and shipped complete with the strike, screw packs and cylinder as required in one carton. The cross bars are cut to the correct length, based on door width. Specifications For Doors Wood or metal. 1-3/4" (44.5mm) thick standard. Other door thickness, consult factory. 4-1/2" (114mm) minimum stile Mounting Supplied standard with wood and machine screws. Through-bolts available on order Chassis Cover Brass, bronze or stainless steel Chassis Nonferrous alloy Crossbar 1" brass, bronze and stainless steel tubing. Specify 42- for reinforced cross bar Hand Handed, please specify hand when ordering Mortise Lock 900 Series Mortise Lock, non-reversible Dogging Standard Allen key dogging Strike C908 standard for panic and fire rated Fire Exit Hardware See chart page 3 C908 Strike 8 1-1/4" (32mm) 3-3/8" (86mm) 1-1/4" (32mm) 4-7/8" (124mm) 3/32" (2mm) Curved lip ANSI A115.1 Handed. 1-1/4" lip standard Longer, lips in increments of 1/4" through 2-7/8" available Black nylon coated 815 Open Back Strike 4-7/8" (124mm) 1-1/4" (32mm) 3-3/8" (86mm) ANSI A Open Back Beveled 1/8" in 2" Specify hand of active door B label Required for pairs of doors with 9700 and 9900 on pair Black nylon coated Single Door Pair of Doors Trim 815 Open back strike Trim

9 9900 Functions and Trims How to order: Options Series Function Trim Hand O/S Finish I/S Finish Door Width 10-SG ETL RHR " Options Series ET Trim Exits with ET Trim, specify lever design after the ET designation (e.g., ETL) Lever Designs for ET Controls A, B, E, F, J, L, P, W Also available with Coastal Series & Studio Collection Levers Note: Voltage must be specified for 73, 74, 75 & 76 function ET trims (12v or 24v) PRK Knob Trim PRK Trim with K knob is through-bolted to the chassis. To order: PRK trim less exit device, Specify: 814-PRK for 04 function Specify: 810-PRK for 10 function Specify: 813-PRK for 13 function Specify: 825-PRK for 15 function Pull & Thumb Piece Trim Section SARGENT ANSI Function Function Numbers Numbers SARGENT Function Numbers Description & Cylinder Info (1-3/4" Door) ANSI Type Panic & Fire Note: Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32 or 32D to match accordingly. For nickel finishes, specify 14/32 or 15/32D to receive nickel finished trims and stainless exit devices Function without cylinder is available as a 73 Function ** 76 Function without cylinder is available as a 74 Function Description & Cylinder Info. (1-3/4" Door) Night Latch Key Retracts Latch #46 Cylinder Supplied 9904 x ET_ No outside Operation (No Cylinder) No outside Operation (No Cylinder) ET Control is used as Pull Only 9910 x ET_ Key Outside Unlocks/locks Trim #41 Cylinder Supplied 9913 x ET_ Passage Only (No cylinder) 9915 x ET_ ** ANSI Function Numbers Electrified ET Trim - Fail Safe Power Off, Unlocks Lever (No Cylinder)** Electrified ET Trim - Fail Secure Power Off, Locks Lever (No Cylinder)** Electrified ET Trim - Fail Safe Power Off, Unlocks Lever, Key Retracts Latch #46 Cylinder Supplied Electrified ET Trim - Fail Secure Power Off, Locks Lever, Key Retracts Latch #46 Cylinder Supplied Night Latch-Key Retracts Latch #41 Cylinder Supplied 814-FLL 814-FLW 814-MAL 814-PTB 814-STS No O/S Operation or Cylinder (Pull Only) 810-FLL 810-FLW 810-MAL 810-PTB 810-STS Passage Only (No cylinder) 828-FLL 828-FLW 828-MAL 828-PTB 828-STS Key Outside Unlocks/locks Trim #41 Cylinder Supplied 866-FLL 866-FLW 866-MAL 866-PTB 866-STS 9773 x ET_ 9774 x ET_ 9975 x ET_ 9976 x ET_ Night Latch Key Retracts Latch #41 Mortise Cylinder Supplied 9904 x PRK No outside Operation PRK used as a Pull only Classroom Key Outside Unlocks/locks Trim #41 Mortise Cylinder Supplied Trim Designations Use three letter designations (Ex PTB ) when ordering the exit device with trim Use the six digit designation (Ex 866-MAL ) when ordering trim without an exit device, always specify finish & hand Note: Thumb piece trims used with mortise lock exit devices are handed Note: Thumb piece trims for 63 and 66 function devices are identical and are identified as 66 function when trim is ordered separately Note: FLW trim is not available in 32(629) or 32D(630) 9910 x PRK 9913 x PRK Passage Only (No cylinder) 9915 x PRK Series 9900 Panic & Fire 9904 x Trim Designation 9910 x Trim Designation 9928 x Trim Designation 9963 x Trim Designation Mechanical Options: CPC- *** SG- TB- Cylinder Options: P P P P P- 73-7P F F BR- LC- *SC- *SE- * Options are not available with the following functions: 04 x ET, 75 & 76 *** Only available with 15, 26D, and 32D finishes Available Finishes SARGENT Finishes BE 10BL D 26 26D 32 32D BSP 9 BHMA Finishes E

10 9400 Series Narrow Stile Concealed Vertical Rod Exit Device How to order: Options Series Function Hand Finish Door Width Door Height AFF RHR 32D 36" 84" 36" 9400 CVR Exit Device The 9400 Series Exit Device is available with two functions: Night latch No outside operation (no cylinder) 9400 Night Latch Cylinder Retainer Key retracts latch Standard with 9404 & Supplied with a # 41 Cylinder 10 Specifications For Doors Mounting Chassis Cover Chassis Crossbar Hand Dogging Strikes Rod Trim Opening Height Stile Width Projection Backset Cylinder Metal doors with 1-3/4" (44.5mm) thickness only. Requires proper reinforcements Supplied standard with machine screws. Brass, bronze or stainless steel Nonferrous alloy Warranty Certifications / Compliance ANSI Fire Exit Hardware See chart on page Top Strike Standard Top Strike for /32" 2" x 1-3/8" oval seamless tubing; standard length for doors up to 36"; crossbar available for doors 36-1/2" to 48" Field Reversible. Order as RHRB or LHRB Standard Allen key dogging Less dogging available, special order top strike pack; bottom strike pack 3/8" solid steel (top); 1/2" steel tubing Rods for doors 8'6" standard Rods for doors 8'6" to 10'8" optional Night Latch Cylinder Retainer with 04 function; 862, 863, 864 pulls available separately 8'6" standard to 10'8" optional 2-1/8" minimum with 1/2" stop, single door; 1-3/4", pair of doors 4-7/8"; 3-1/8" depressed 1-3/8" on single door with 3/8" stop; 1" on pair of doors without mullion 41 Mortise cylinder Supplied with 9404 / only; Cylinder kit includes: Cylinder, Night Latch Cylinder Retainer, and mounting screws 1 Year Limited ANSI A156.3 Grade 1; A117.1 Accessibility Code Bottom Strike Standard Bottom Strike for 9400 Strike to be flush with finish floor 1-3/8" 4-3/16" Options 9400 Mechanical Options: Cylinder Options: F1-82- BR- SC- SE-

11 9898 Reversible Rim Exit and Trim for the 9898 Rim Exit Device Specifications For Doors Mounting Chassis Cover Chassis Crossbar Hand Dogging Strike Fire Exit Hardware Wood or metal. 1-3/4" (44.5mm) thick standard. 2-1/4" (57mm) thick on order. Other door thickness, consult factory. 4-1/8" (105mm) minimum stile Supplied standard with wood and machine screws. Through-bolts available on order Brass, bronze or stainless steel Nonferrous alloy 1" brass, bronze and stainless steel tubing. Specify 42- for reinforced cross bar Non-handed Standard Allen key dogging 649 Strike Not available Available Trim Designs & Functions to be used with any 9898 Device All trims are non-handed for 9898 devices Determine available Trim Designs & Functions with chart below How to Order Trim: Specify Product Designation from the chart below and finish required Functions ANSI Descriptions Key Retracts Latch #34 Cylinder Required & Supplied No O/S Operation or Cylinder (Pull Only) 814-FLL 810-FLL 814-FLW 810-FLW The 9898 Multi-fuction Rim Exit Device is the perfect stocking device. 4 functions determined by trim specified Device & trim sold separately; easy to mix and match 5 available trim designs Trim is non-handed Device is field reversible How to Order: 9898 x Door Width Note: If door width information is not supplied, SARGENT will supply a cross bar for a 44" door width Cross bars can easily be cut to length in the field Available options for 9898 exit devices are 42-, ***SG-& CPC Available options for 9898 trim are 10-, 11-, , , , 21-, 22-, 60-, 63-, 64-, 81-, 82-, F1-82-, 83-, F1-83-, 84-, BR-, CPC- and ***SG- *** Only available with 15, 26D, and 32D finishes 649 Strike 814-MAL 810-MAL No O/S Operation or Cylinder (Exit Only) N/A N/A N/A Passage Only (No cylinder) Key Outside Unlocks/ locks Thumb Piece # 34 Cylinder Required & Supplied 828-FLL 866-FLL 828-FLW 866-FLW 1-5/32" (29mm) Product Designation 828-MAL 866-MAL Note: Thumb piece trims for 63 and 66 function devices are identical and are identified as 66 function when trim is ordered separately Note: FLW trim is not available in 32(629) or 32D(630) 3-11/16" (94mm) For 9898 Surface applied Black nylon coated 814-PTB 810-PTB 802-PTB 828-PTB 866-PTB 3/4' (19mm) 814-STS 810-STS N/A 828-STS 866-STS 11

12 ET Trim, Levers and Pulls ET Lever Controls A Lever B Lever 3-9/16" MAX* (90mm) Handed 8-1/16" (205mm) 3-1/2" (89mm) 3-1/8" (79mm) 1- (46mm) *Projection varies by lever design. 2-1/2" (63mm) projection with L Lever E Lever 4-1/2" (114mm) F Lever 4-5/8" (117mm) ET lever trim can be used with most 90 Series exit devices. Easy operating lever handle allows convenient one hand operation. ET Escutcheons are forged or cast brass and the levers are brass or bronze. Stainless steel is available. ET Designations (Used to order ET trim without device) Specify: 704 x ET, 706 x ET, 710 x ET, 713 x ET, 715 x ET, 773 x ET, 774 x ET, 775 x ET & 776 x ET include lever design and finish and hand Example: 713 x ETJ x 26D x RHR Note: ET trim used with 90 Series device use standard ET trims with out a suffix 3" (76mm) 4" (102mm) 3-1/4" (83mm) 4" (102mm) J Lever* 2-3/4" (70mm) W Lever 3" (76mm) * Lever returns within 1/2" (13mm) of door face /16" (119mm) 1/2" (13mm) 4-11/16" (119mm) L Lever* Pulls 2-3/8" (60mm) 1-3/4" (44mm) /4" (70mm) 1/2" (13mm) 4-1/2" (114mm) SIDE PROFILE 862 1" Dia. (25mm) 4" (102mm) P Lever* 10" (254mm) MTG Holes 3" (76mm) " Dia. (25mm) 4" (102mm) 5/16" (8mm) 4-15/16" (125mm) 18" (457mm) MTG Holes 3/4" Dia. (19mm) 3-1/2" (89mm) 10" (254mm) MTG Holes

13 Studio Collection Levers Odéon Series Features Studio Collection levers can be used with all SARGENT 90 Series exit devices with ET trim All levers - solid brass or stainless steel Available with all lever functions Finishes available: 03, 04, 09, 10, 10B, 10BE, 10BL, 14, 15, 20D, 26, 26D, 32 & 32D, BSP Always specify hand MN MH MK Centro Series Rialto Series MS MD MJ MP ND* Aventura Series MO MZ* MB MU MV MX* NS* Notting Hill Series ME NJ* MF NF MQ MG MT MI MM NI* MY* Gramercy Series** MW* * Lever returns within 1/2" (13mm) of door face Levers are not available with Simplí Roseless trim ** The Gramercy Levers are customized. Refer to the next page for ordering information NU* RCM RAL REM RAM RAS RAW RAG RGM 13

14 Ordering Gramercy Series Levers Elements of Gramercy Series Levers REM RCM RAM, RAW, RAS, RAL Lever Part Number Shank Finish* Insert Grip Finish Plain REM Polish Stainless (629) or Satin Stainless (630) With Raised Band RCM Polished Stainless (629) n/a With Metallic Insert RAM Polished Stainless (629) With Wood Insert With Santoprene Insert With Leather Insert RAW RAS RAL * ET trim finish is designated by shank finish selected Grip finish must match shank finish Polished Stainless (629) or Satin Stainless (630) Polished Stainless (629) or Satin Stainless (630) Polished Stainless (629) or Satin Stainless (630) n/a Satin Stainless (630) Birch (BH) Black (BK) Black (BK) or Brown (BN) Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630) Polished Stainless (629) Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630) To order Gramercy Series levers with SARGENT products, see the examples below. When specifying finish, use the last two digits of the BHMA standard finish code, i.e. use 29 for polished stainless, BHMA finish 629. How to specify: x ET trim with Gramercy levers Options Series Functions Voltage Trim Lever select from pages 19 & Series select from pages 4-11 specified for electrical functions Gramercy Lever Information Leather insert Shank Finish* polished or satin stainless Insert Finish black or brown Grip Finish polished or satin stainless Hand RHR, RH, LHR, or LH Inside Finish select from page 22 Door Width Opening Height For vertical rod devices VDC ET RAL 29 BN 29 RH 32D 36" 84" 36" AFF Above Finished Floor

15 Coastal Series Levers and Thumb Piece Pulls Coastal Series levers with ET Trim is available with 9900, 9800 & 9700 Devices C* - Coronado R - Rockport All levers solid cast brass All standard functions available Finishes available: 03, 04, 09, 10, 10B, 10BE, 10BL, 14, 15, 20D, 26 & 26D, BSP * Lever returns within 1/2" (13mm) of door face Y - Yarmouth 2-3/4" (70mm) 4-3/4" (121mm) 2-1/2" (64mm) 4-1/4" (108mm) G - Gulfport S - Sanibel 3-1/4" (83mm) 4-1/2" (114mm) Specify hand when ordering Pulls and Thumb Piece Trims Pulls and trims are through-bolted. Through-bolting of trim allows for perfect alignment of thumb pieces, cylinders and spindles. Through-bolts pass through the chassis of the devices and are bolted directly to the trim. FLL 3-1/2" (89mm) 4-1/2" (114mm) Specify hand when ordering 1-3/4" (44mm) 2-1/16" (52mm) FLW 4-1/16" (103mm) Specify hand when ordering 1-3/4" (44mm) 4-1/2" (114mm) 2-1/16" (52mm) PRK PTB 2-1/4" (57mm) 3-1/2" (89mm) 8" (203mm) 15" (381mm) 2-1/2" (64mm) 1-15/16" (49mm) 6" (152mm) STS 1-5/8" (41mm) 14-5/16" (364mm) 9-5/8" (244mm) 2-1/4" (57mm) 6" (152mm) 7-3/16" (198mm) MAL 2-5/8" (67mm) 14-5/16" (364mm) 14-1/4" (362mm) 2-1/16" (52mm) 6" (152mm) 6" 152mm 15

16 Electromechanical Functions and Accessories 73 & 75 Electromechanical (Fail Safe) 74 & 76 Electromechanical (Fail Secure) 73 Functions: Fail Safe - Power Off, Unlocks Lever (No Cylinder) 74 Functions: Fail Secure - Power Off, Locks Lever (No Cylinder) 75 Functions: Fail Safe - Power Off, Unlocks Lever includes Cylinder override 76 Functions: Fail Secure - Power Off, Locks Lever includes Cylinder override 75 & 76 functions: the key retracts latch Exit Device always allows egress Voltage requirements: 12VDC or 24VDC Regulated; always specify voltage 250mA at 24VDC or 500mA at 12VDC Provided with ElectroLynx 8-Pin Connector 12VDC & 24VDC Power Supplies: UL Class 2 Listed Four 12V models and four 24V models available Integral battery charging capability keeps sealed lead acid gel/cell at full charge in case of line voltage failure (737-battery sold separately) Fused line voltage input with one, four, or eight DC outputs (depending on model) Each circuit can be individually turned on and off via a slide switch; the power status of each is shown by an LED In the event of a DC short the problem is confined to the zone of difficulty Fire alarm interface standard Requirements for Electrical and Data Transfer To answer the demand for smart electronic access control and locking solutions that require fast, easy, and cost-effective installation, ASSA ABLOY Group brands use the ElectroLynx standardized plug-in connectors and color-coded wiring system. With ElectroLynx, doorway components come pre-wired for easy hookup to the power source. Key to the system is the transfer device hinge that carries power from the frame to the locking hardware. Features of ElectroLynx : Makes it easy to bring power to the locking hardware Wires have connectors that snap together, like plugging a telephone into a jack To connect Electrified Trim to the electronic access control system, the following items are required: Electrified Trim (73, 74, 75 & 76 function ET s) ASSA ABLOY Door Group pre-wired door, or ElectroLynx retrofit cable (order from McKinney) Electronic transfer device (ElectroLynx electronic transfer hinge or Electrical Power Transfer with standard hinge, from McKinney) ElectroLynx cable from the hinge to above the ceiling (order from McKinney) Information regarding cable selection, hinge requirements and order strings can be found in the McKinney Transfer Device Solutions catalog. Consult WIRE (9473) with questions on application specifications and requirements. McKINNEY QC ElectroLynx Hinges are recommended 16 SARGENT Model No. DESCRIPTION V - 1 AMP POWER SUPPLY V - 3 AMP POWER SUPPLY V AMP POWER SUPPLY V - 6 AMP POWER SUPPLY V - 5 AMP HOUR BACKUP BATTERY SARGENT Model No. DESCRIPTION V - 1 AMP POWER SUPPLY V - 2 AMP POWER SUPPLY V - 4 AMP POWER SUPPLY V - 6 AMP POWER SUPPLY V - 5 AMP HOUR BACKUP BATTERY

17 Mullions: Aluminum, Steel and Electrified Aluminum Mullions Product Designation 650A 980 L980 Description Removable Removable Lockable Material Aluminum Aluminum Aluminum Standard Finish Options US28/Satin Anodized Aluminum Specify 650A x 10B for 313AN to match 10B Prime Coat Specify 980A for Anodized US28/ Satin Aluminum Aluminum Prime Coat Specify: L980A Anodized Aluminum Specify: L980A x10b for 313AN to match 10B Stk Size 96" 96" 96" Max Stk Height 120" 120" 120" Pre-prepped 658 Strikes Included No No Cylinder Size Not Required Not Required #41 Shape 1-1/2" x 2-1/2" T Shaped 2-1/2" x 3" T Shaped 2-1/2" x 3" Electrified EL980 Electrical Lockable Steel Gray Paint Wall Mounting Kit: Top Ret Pack : " 120" No #46 Only Rectangular 2" x 3" Misc. Information and Accessories Includes 651 Stabilizers and imbedded Weather Stripping Top Retainer Bottom Retainer Top Retainer Bottom Retainer Adapter for narrow transom: Aluminum Prime Coated 507A - Anodized Aluminum All Cylinder Options Available Wall Mount Kit Top Ret Pack Bottom Ret Pack Cylinder Kit 980C1* For use with Electric Strikes and Monitoring, Quick Connect Wiring Supplied Cylinder Kit 980C2* * Note: Cylinder Kits must be ordered separately Misc. Information Accessories Designed for severe wind load conditions due to hurricanes or windstorms. Tested to Dade County Protocols & ASTM Standards Top Ret Pack Bottom Ret Pack Top Retainer Shim Kit * Note: Cylinder Kits must be ordered separately Note for HC980/12-HC980 Mullions: Designed for severe wind load conditions due to hurricanes or tornadoes Tested to Dade County protocols and ANSI ASTM Standards and FEMA Fire labeled version Replacement lock kits are available for lockable mullions Part numbers for each model are listed in the price book Steel Mullions Product Designations HC S L980S Description Hurricane Code Standard Mullion Lockable Material Steel Steel Steel Fire Rated Specify 12-HC980 Specify Specify 12-L980 Fire Rated Max Height 96" 96" 96" Finish Gray Paint Gray Paint Gray Paint Stk Size 96" 96" 96" Max Stk Height 96" 120" 120" Pre-prepped No No No Cylinder Size Not Required Not Required #41 Std (#42 & #43 available) Shape Rectangular 2" x 3" Rectangular 2" x 3" Rectangular 2" x 3" Channel Iron & Malleable iron top & bottom retainers Top Ret Pack Bottom Ret Pack Top Retainer Shim Kit HCL980 Mullion Information Fire rated for 8'0" x 8'0" paired openings Wall Mounting Kit Top Ret Pack Bottom Ret Pack Top Retainer Shim Kit Cylinder Kit 980C1* Model 12-HC-L980 may be supplied for doors UL fire rated up to and including 3 hrs not exceeding 8 ft in width and height Meets the following standards: ANSI , ASTM E330, ASTM 1886, ASTM 1996, TAS 201, TAS 202 & TAS 203 HCL980 Lockable Hurricane Code Steel Specify 12-HCL980 96" Gray Paint 96" 96" No #41 Std (#42 & #43 available) Rectangular 2" x 3" See Notes Below Top Retainer Pack: Bottom Retainer Pack: Top Retainer Shim Kit Cylinder Kit 980C1* Lockable Mullion Cylinder Kit Options Lockable mullions are shipped without cylinders. Order Cylinder Mullion Kit separately. L980, L980A, L980S & HC-L980 are 10, , , 11-, , 11-60, , , P-, P-, P-, 21-, 22-, 60-, 63-, 64-, 70, 72-, 73-, , P-, 73-7P-, 81-, 82-, F1-82-, 83-, F1-83-, 84-, SC- & SE- EL980 are 10, , , 11-, , 11-60, , , P-, P-, P-, 21-, 22-, 60-, 63-, 64-, 70, 72-, 73-, , P-, 73-7P-, 81-, 82- & F1-82- Note: See page 20 for option details 12-HD980 Heavy Duty Steel Specify 12-HD " Gray Paint 120" 120" No Not Required Rectangular 2" x 3" 12-HD980 is for pair of doors over 8'0" to 10'0" includes two piece strikes Top Ret Pack Bottom Ret Pack Top Retainer Shim Kit

18 Mullion Accessories, Stabilizers and Door Coordinators Mullion Accessories RK980 Latchbolt assembly retrofit kit with top and bottom retainers for 980 aluminum mullion. 507 Narrow Transom Bars Adapter Available with 980 and 980A Required when soffit is 1-1/4" (32mm) to 2" (51mm) wide 980S Mullion Application All steel mullions are 2" x 3" Soffit 19/32" (15mm) Top Retainer Door Mullion Body 980 Mullion & L980 Lockable Mullion 651 Mullion Stabilizer Kit 650A Mullion Stabilizer block Furnished standard w/650a Mullion Order as a 651 Kit Lockable Mullion 980C1 Cylinder Mullion Kit Lockable mullions only Aluminum and steel Includes cylinder and collar 980C2 Cylinder Mullion Kit Lockable mullions Electrified only Includes cylinder and collar 18 Mullion Weights & Packaging Product Avg Wt Case Exit Device with Trim 15 lbs 1 ea 980 Mullion 18 lbs 1 ea Mullion 40 lbs 1 ea 650A Mullion 18 lbs 1 ea Cylinder Nut Wrench This wrench simplifies the installation and removal of mortise cylinders nuts used on 700 Series Auxiliary Control (80 Series ET Trim). Part number Door Coordinators Prevents active door from closing before inactive door closes Meets Federal Specification FF-H-106a Type 836. Cast bronze with rubber rollers U.L. Labeled when used with Fire Exit Hardware 3487 (6-3/4" length; 171mm) for pairs of doors equipped with outside astragal Packed with wood and machine screws Finishes: 10, 26D

19 Mechanical Options and Descriptions Mechanical Options: Fire Rated 12- UL Fire Label Exit hardware SVR Bolt 14- Sliding bolt bottom case for 9700 Alternate Strike /8" (124mm) ANSI flat lip strike (for 9900 Series Mortise Lock Exit Devices) Thick Doors 31- Doors over 1-3/4" and/or Panels (Specify door thickness, panel thickness & location as required) (Not available with 9400 Devices) Extended lip strike supplied for 9900 Series Security Fasteners Reinforced Cross Bar Electrical Options Tactile Warning Options Finish Protection 36- Six lobe security head screws 37- Spanner head screws 42- Reinforced Cross Bar (Not available with 9400 Devices) 54- Monitors ET Lever movement with Internal micro switch in ET Control 76- Tactile Warning - Milled Outside Lever (Not available with Studio & Coastal Levers and the A Lever) 85- Tactile Warning - Abrasive strip on Cross Bar 86- Tactile Warning - Abrasive coating on Outside Lever 87- Tactile Warning - Abrasive strip on Cross Bar & Abrasive coating on Outside Lever CPC- SG- Clear Powder Coat (Available for 32 & 32D Finishes) MicroShield antimicrobial clear powder coat (only available with 15, 26D and 32D finishes) Through Bolts TB- Through-bolts for 9900, 9800 & 9700 Devices Note: Tactile Warning with Knurled Cross Bars is available, please consult factory (not available with 9400 devices) Mounting Heights 36" (914mm) Cross Bar above finished floor for standard application Hand Left Hand Reverse LHR Inside Outside Right Hand Reverse RHR Door Opening Height 1/8" (3mm) Door 1/4" (6mm) Stop Height 36" AFF Finished Floor 19

20 Cylinder Options and Descriptions Cylinder Options: Degree Key System Signature Key System Signature- LFIC Removable Core XC- Key System XC- Large Format Interchangeable Core (Removable Core) XC- Small Format Interchangeable Core 20 DG1- DG1-21- DG1-60- DG1-63- DG1-64- DG1-65- DG2- DG2-21- DG2-60- DG2-63- DG2-64- DG2-65- DG3- DG3-21- DG3-60- DG3-63- DG3-64- SARGENT Degree Key System Level 1 (bump resistant with patented keys) Degree Level 1 Construction Master Keying Degree Level 1 Removable Disposable Construction Core Degree Level 1 Removable Core Degree Level 1 Removable Construction Keyed LFIC Degree Level 1 Unassembled/Uncombined Core SARGENT Degree Key System Level 2 (geographically exclusive; bump and pick resistant) Degree Level 2 Construction Master Keying Degree Level 2 Removable Disposable Construction Core Degree Level 2 Removable Core Degree Level 2 Removable Construction Keyed LFIC Degree Level 2 Unassembled/Uncombined Core SARGENT Degree Key System Level 3 (geographically exclusive; UL437 certified; bump and pick resistant) Degree Level 3 Construction Master Keying Degree Level 3 Removable Disposable Construction Core Degree Level 3 Removable Core Degree Level 3 Removable Construction Keyed LFIC 10- SARGENT Signature Key System (Not Available with other Key Systems) SARGENT Signature Construction Key System (Lost Ball) SARGENT Signature Removable Core Cylinder 11- XC Key System (Not available with other Key systems unless specified) XC- Construction Key System (Lost Ball) Device to accept XC- Permanent Removable Core, Disposable plastic Core- provided Device provided with XC- Removable Core Cylinder - (Includes masterkeying, grand masterkeying) Device provided with Keyed construction core to accept XC- Removable Permanent Core (ordered separately) P- Device to accept XC- SFIC ( 7-Pin) XC- Permanent Cores, plastic disposable core provided P- Device to accept XC- SFIC (7-pin Keyed Construction Core provided) cylinder Permanent core ordered separately P- Device provided with XC- Small Format 7-Pin interchangeable core (Includes masterkeying, grand masterkeying) P- Device provided to accept XC- Uncombinated 7-Pin SFIC (Permanent) Core - (Packed Loose) Note: For V-10 Cylinders and information, contact ASSA,

21 Cylinder Options and Descriptions Cylinder Options: Construction Key Systems Old Style Removable Core Large Format Interchangeable Core (Removable Core) Small Format Interchangeable Core Keso & Keso F1 52- Removable Construction Core (Old Style) Permanent core ordered separately (existing systems only) Device to accept SARGENT Permanent Removable Core, Disposable plastic Core provided (Permanent Cores ordered separately) 63- Device provided with Removable Core Cylinder - (Includes masterkeying, grand masterkeying) 64- Device provided with Keyed construction core to accept Removable Permanent Core (ordered separately) 70- Device to accept 6- or 7-Pin SFIC Permanent Cores, plastic disposable core provided Device to accept 6- or 7-Pin SFIC (6-Pin Keyed Construction Core provided) Cylinder (Permanent Core ordered separately) 73- Device provided with 6-pin SFIC (Includes masterkeying, grand masterkeying) Device provided to accept Uncombinated 6-Pin SFIC (Permanent) Core - (Packed Loose for field keying) P- Device provided to accept Uncombinated 7-Pin SFIC (Permanent) Core - (Packed Loose for field keying) F1-82- Device provided with SARGENT Keso F1 Security Cylinder (Patented) 83- Device provided with SARGENT Keso Security Removable Core cylinder F1-83- Device provided with SARGENT Keso F1 Security Removable Core cylinder (Patented) 84- Device provided with SARGENT Keso Construction Cores (Permanent Cores ordered separately) Added Security BR- Bump Resistant Cylinder (Available with Conventional & Conventional XC Cylinders Only) Less Cylinder Schlage Keyways 21- SARGENT Lost Ball Construction Keying for Conventional, XC and Signature Series (N/A with 63- or 73-) 22- SARGENT Construction Split Key System for Conventional Cylinders (Existing Systems Only) (N/A with 10-, 11-, 63- or 73-) 51- Removable Core Cylinder (Old Style) provided (existing systems only) P- Device provided with Small Format 7-Pin Interchangeable Core (Includes masterkeying, grand masterkeying) 81- Device provided with housings to accept Keso (83) & Keso F1 (F1-83-) removable cores. (Permanent Cores ordered separately) 82- Device provided with SARGENT Keso Security Cylinder LC- SC- SE- Less Cylinder - SARGENT supplies standard blocking rings for 1-1/8" Cylinders (For longer cylinders order collars/rings separately) Schlage C keyway cylinder, 0 bitted Schlage E keyway cylinder, 0 bitted 21

22 How to Order Example Order: ETMR 12VDC RHR 26D 32D 36" 84" 36" Options Device Type Function Trim Voltage Available Options Listing Pgs Through-bolts Mortise 04 - Night Latch 98 - Rim 06 - Night latch 97 - SVR 10 - Dummy 94 - CVR Narrow Device Through- *Ordering bolts Classroom 15 - Passage 28 - TP Passage 63 - TP Classroom 73 - Solenoid Fail Safe 74 - Solenoid Fail Secure 75 - Solenoid Fail Safe w/cyl 76 - Solenoid Fail Secure w/cyl For ET trim specify ET followed by Lever design, See pages For Thumb Piece Trims and Pulls specify Trim Designation as specified by Device Type For 300 Series Auxiliary Controls; specify 306 or 313 with 10, 73 or 74 Function Devices For PRK Trim; specify PRK 12VDC 24VDC Voltage required for Solenoid Controlled Functions - 73, 74, 75 & 76 How to Order Exit Devices *Specify Finish To order Through-bolts, specify TB- Option. Examples: TB-9804 x FLL x RHR x 32D or TB-9804 x PRK x LHR x 10. Through-bolts and mortise nuts must be specified to mount fire exit devices on composite fire doors with steel, wood or plastic covering. Note: PRK Trim: When PRK trim is ordered with 9700, , 9800 and 9900 Series Exit Devices, placement of bolts at center case differs (See illustration) Hand Finish RHR LHR Legend Outside Finish Available Finishes page 23 Inside Finish Inside Finish Available Finishes page 23 AFF - Above Finish Floor ET - SARGENT External Lever Trim CVR - Concealed Vertical Rod TP - Thumb Piece Trim SVR - Surface Vertical Rod Center Bearing Bracket Door Width If door width is supplied Cross Bar will be cut to size & 9900 PRK Opening Height Required for Vertical Rod Exit Devices AFF 36" Cross Bar above finished floor for std application All exit devices used on doors 48" wide and wider will be furnished with a matching center bearing bracket at an additional charge. This bracket assists in supporting the long crossbar and adds an extra spring to help counter balance the crossbar.

23 Finishes and Finish Care Finishes SARGENT # BHMA# Description How to clean Avoid these cleaners Polished brass, clear coated Satin brass, clear coated Polished bronze, clear coated Satin bronze, clear coated 10B 613 Oxidized bronze, oil rubbed 10BE 613E Dark oxidized satin bronze, equivalent BSP Black Suede Powder Coat 10BL+ 614 Oxidized satin, bronze, clear coated 20D 624 Statuary dark bronze, clear coated 32** 629** Polished stainless steel Mild non-abrasive detergent with damp cloth or sponge Lemon oil polished with dry cloth Mild non-abrasive detergent with damp cloth or sponge Abrasive cleaners, bleach solvents, steel or bronze wool Abrasive cleaners, bleach solvents, steel or bronze wool Abrasive cleaners, bleach solvents, steel or bronze wool 32D** 630** Satin stainless steel Plastic pad or bronze wool Cleaners, solvents, bleach, steel wool + Note: Finish not available, 9400 / PRK Trim is not available in 32 or 32D ** Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32 or 32D to match accordingly. 26 or 26D is automatically supplied as a trim finish when 32 or 32D is specified for the exit device finish. For nickel finishes, specify 14/32 or 15/32D to receive nickel finished trims and stainless exit devices. Note: Arms Nickel Plated to match 32 and 32D Note: FLW Trim is NOT available in 32 or 32D To avoid discoloration and pitting: Keep stainless steel away from contact with other metals Avoid cleaning with mineral acids or chlorine products Avoid cleaning with abrasive products like sandpaper or steel wool Rod Replacement Kits Product Top Rod Kit * Bottom Rod Kit ** 3 670T 670B To maintain the finish: Remove any contamination before damage occurs Protect with a metal polish or car wax Suggested Architect s Specification All exit devices must be listed under panic hardware in accident equipment list of Underwriters Laboratories All exit devices, regardless of type, shall be of matching design Crossbar must have minimum wall thickness of.062" or be reinforced Main arm pivots shall be stainless steel Springs shall be stainless steel Crossbars and arms shall be counter balanced by springs in both center case and hinge style cases All exit devices shall be of chassis mounted unit construction with removable covers Top and bottom rods of vertical rod devices shall be a minimum of 3/8" diameter Where labeled fire doors are used as exits, they must be equipped with labeled fire exit hardware All crossbars on exit devices to be locked down by inside dogging feature accomplished by depressing crossbar and turning key Note: Finish Information Required * Door Height & Rail Location Required ** Rail Location Required 571 Rod Extension Kits For use on surface mounted vertical rods Kits available in 6" (15.2cm), 12" (30.4cm) or 18" (45.7cm) lengths To order: Specify length and finish Example: 571-6" x 26D 23