INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Lucas Booth
6 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory P/N 08U97-TX4-200 Application 2016 RDX Publications No. VERSION 1 Issue Date APRIL 2015 PARTS LIST Steering wheel Illustration of the Steering Wheel in the Vehicle 2 TORX bolts Steering wheel bolt QA00402AB Information INSTALLATION TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 10 mm Open end wrench 10 mm Hex bit Ratchet T30 TORX bit Torque wrench Steering wheel puller HDS The following tool is available through the Honda Tool and Equipment Program. On the in, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under Search. Or, call Plastic Trim Tool (T/N SILTRIMTL10) Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Observe all safety notes and precautions in the service manual in addition to those in this installation instruction. Be careful not to damage the vehicle. After installing the steering wheel, you must align the steering wheel spoke angle to the straight ahead position by adjusting the front toe. 1. Turn the steering wheel so the front wheels are in the straight-ahead position. 2. Disconnect the negative cable from the battery, and wait at least 3 minutes before you start to install the steering wheel American Honda Motor Co., Inc. All Rights Reserved. BII (1504) 08U97-TX of 8

2 3. Remove the access panel from the underside of the steering wheel. 6. Remove the airbag (two TORX bolts). Do not drop the removed airbag or hit it on anything. Place the removed airbag in a safe place with the pad surface (top) facing upward. CABLE GUIDE ACCESS PANEL HORN 4 RETAINING TABS 2 TORX BOLTS (Discard.) QA00403AB SPRING-LOADED SLEEVE AR 4. Remove the horn connectors from the cable guide and unplug the horn connectors. 5. Remove the airbag connectors from the cable guide and unplug the airbag connectors. To unplug the airbag connectors, pull the spring-loaded sleeve toward the stop while holding the opposite half of the airbag connector, then pull the airbag connector halves apart. Pull on the sleeve and not on the harness wires. 2 of 8 BII (1504) 2015 American Honda Motor Co., Inc. All Rights Reserved.

3 7. Unplug the vehicle connector from the cable reel, and loosen the steering wheel bolt. BOLT (Loosen.) 10. Remove the steering wheel cover (four screws). COVER PULLER PULLER BOLT 4 SCREWS QA00405AB 11. Remove the lower cover (two screws). CABLE REEL SRS VEHICLE BOLT (Discard.) QA00404BB 8. Using a steering wheel puller, remove the steering wheel. Do not thread the steering wheel puller bolts in more than 10 mm. Be careful not to rotate the steering wheel during removal. 9. Remove the steering wheel bolt, then remove the steering wheel. 2 SCREWS LOWER COVER QA00406AB 2015 American Honda Motor Co., Inc. All Rights Reserved. BII (1504) 3 of 8

4 12. Remove the four screws from the left and right paddle switches. RIGHT PAD- DLE SWITCH LEFT PADDLE SWITCH 14. Remove the cable guide assembly (including both paddle switches, the audio switch, and the cruise switch) from the steering wheel (four retaining tabs). (Discard.) 4 SCREWS QA00407AB 4 RETAINING TABS CABLE GUIDE QA00409AB 13. Remove the two screws. 15. Install the cable guide assembly onto the new steering wheel. NEW GROUND TERMINAL 2 SCREWS QA00408AB 4 RETAINING TABS CABLE GUIDE QA00410AB 4 of 8 BII (1504) 2015 American Honda Motor Co., Inc. All Rights Reserved.

5 16. Install the two screws and ground terminal. 18. Install the lower cover to the new steering wheel with two screws. GROUND TERMINAL 2 SCREWS (reused) NEW QA00408AB 2 SCREWS (reused) NEW LOWER COVER QA00406AB 17. Install the left and right paddle switches to the new steering wheel with four screws. RIGHT PAD- DLE SWITCH LEFT PADDLE SWITCH 19. Install the steering wheel cover to the new steering wheel with four screws. COVER 4 SCREWS (reused) NEW QA00407AB NEW 4 SCREWS (reused) QA00411AB 2015 American Honda Motor Co., Inc. All Rights Reserved. BII (1504) 5 of 8

6 If the cable reel was moved, continue with step 20. If it was not moved, go to step Center the cable reel: Rotate the cable reel clockwise all the way until it stops. Rotate the cable reel counterclockwise about three full turns until the arrow mark on the cable reel points up. 21. Route the airbag connector through the opening in the new steering wheel, then install the steering wheel to the steering column shaft in the straightahead position: Make sure the wire harnesses are not pinched. PIN COLUMN SHAFT Rotate clockwise until it stops. Rotate counterclockwise about three full turns until the arrow mark points up. NEW CABLE REEL CABLE REEL ARROW MARK CABLE REEL QA00412BB VEHICLE NEW BOLT Torque: 49 N m (36 lbf ft) NEW QA00413BB 22. Install the new steering wheel bolt. Torque the new steering wheel bolt to 49 N m (36 lbf ft). NOTE: The original steering wheel bolt is coated with locktite, and cannot be reused. When installing the new steering wheel, use the steering wheel bolt included in the kit. 6 of 8 BII (1504) 2015 American Honda Motor Co., Inc. All Rights Reserved.

7 23. Plug the vehicle connector into the cable reel. 24. Install the airbag on the new steering wheel. Make sure that the harness does not get caught between the steering wheel and the airbag. Alternately tighten the right and left TORX bolts so that the clearances between the steering wheel and horn pad are equal on both sides. Torque the TORX bolts to 10 N m (7.2 lbf ft). TORX bolts are coated with loctite, so they cannot be reused. When installing the airbag, use the TORX bolts included in this kit. 25. Reconnect the horn connector and the airbag connector. To reconnect the airbag connector, hold the pawl-side connector, and push on the back of the sleeve-side connector. Do not hold the sleeve, the sleeve is pushed back by the pawl as the two airbag connectors mate. CABLE GUIDE NEW ACCESS PANEL HORN 4 RETAINING TABS 2 NEW TORX BOLTS Torque: 10 N m (1.0 kgf m, 7.2 lbf ft) Make sure the clearances are equal on both sides. SPRING-LOADED SLEEVE HORN PAD QA00414AB AR 26. Secure the airbag connector and horn connector to the cable guide. 27. Reinstall the access panel. 28. Check that all wire harnesses are routed properly and all connectors are plugged in American Honda Motor Co., Inc. All Rights Reserved. BII (1504) 7 of 8

8 29. Reconnect the negative cable to the battery. 30. Connect the HDS, and clear the DTCs. 31. Inspect the following items. If the items do not operate properly, perform the troubleshooting in the service manual. Turn the ignition switch to ON; the SRS indicator should come on for about 6 seconds and then go off. Make sure the horn works. 32. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions. 33. Reset the clock (vehicle without navigation). 34. Make sure the steering wheel is in the straight-ahead position with the front wheels. If the spoke angle of the steering wheel is not in the straight-ahead position with the front wheels, adjust the front toe. 8 of 8 BII (1504) 2015 American Honda Motor Co., Inc. All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory WOODGRAIN LOOK P/N 08U97-TZ5-200 Application 2014 MDX Publications No. BII 48844-49638 Issue Date JUNE 2013 PARTS LIST INSTALLATION Steering wheel 2 TORX bolts Steering