XR500B Universal Voltage Regulator

Transcription

1 XR500B Universal Voltage Regulator The XR500B is a unique voltage regulator that is designed specifically for Professional Electrical Generator Service and Repair Technicians. The XR500B incorporates patented electronic circuitry that allows an installer to match the regulator to many differing configurations of exciters without special transformers or inline resistors. The XR500B can be externally controlled with a PLC or Genset controller by simply adding an optional interface module. Specifications Input Volts: Frequency: Voltage Regulation: Parallel Operation Output Volts: Maximum Continuous Output: Minimum Field Resistance: Min Residual Build up Volts: Physical Size: Weight: Repairable: Internal Protection: External Voltage Adjustment: System Operating Indicator: Optional Static Exciter Modules Optional External Controls 120 / 208 or 240acv 50 or 60hz +/- 1% From NL to FL Yes 120vac input 240vac input 240vac input 5adc 52vdc output 105vdc output 210vdc output 3.5vac 4.75 x 6 x 1 in. 7 oz Yes Fuses Yes Yes Yes Yes

2 Caution: Read this Installation Manual carefully. Warning: Do not use digital equipment to read voltage, Hz or amperage during this installation. Use only Analog sensing equipment! Failure to do so may result in damage to equipment or in personal injury! Make sure that all setup is done off line. Always wear eye protection and never hold the regulator in your hand when energized. The XR500B is a Universal Voltage Regulator that can be configured several different ways to fit differing applications. Before selecting a wiring configuration for the regulator, you must know certain pieces of information about the generator and exciter to be successful in determining the correct hookup for the regulator. Show below is a guide to determine the correct connection of the regulator: Exciter field resistance is more than 40 ohms and exciter full load voltage is rated at 125vdc or less. (Use connection A) Exciter field resistance is more than 21 ohms and exciter full load voltage is rated at 63vdc or less. (Use connection B) Exciter field resistance is more than 10 ohms and exciter full load voltage is rated at 32vdc or less. (Use connection C) Connection A If this generator is going to operate at a speed lower than 50/60 Hz, a disconnect or switch should be placed in series from the generator stator to terminal #1 and #2 on the XR500B. Generator AØ BØ CØ vac For 480vac, either use a transformer with a 240vac secondary or center tap the generator windings. At T7 and T8. N vac Do not connect the input of the voltage regulator to DPE or auxiliary windings! F+ F-! XR500B Universal Voltage Regulator Remote Voltage Adjustment 1w Note: It is not necessary to jumper 7 and 8 terminals if not using the Remote Voltage Adjustment! 2

3 Connection B If this generator is going to operate at a speed lower than 50/60 Hz, a disconnect or switch should be placed in series from the generator stator to terminal #1 and #2 on the XR500B. Generator AØ BØ CØ vac For 480vac, either use a transformer with a 240vac secondary or center tap the generator windings. At T7 and T8. F- F+ N vac Do not connect the input of the voltage regulator to DPE or auxiliary windings!! XR500B Universal Voltage Regulator Remote Voltage Adjustment 1w Note: It is not necessary to jumper 7 and 8 terminals if not using the Remote Voltage Adjustment! Connection C If this generator is going to operate at a speed lower than 50/60 Hz, a disconnect or switch should be placed in series from the generator stator to terminal #1 on the XR500B. Generator AØ BØ CØ vac For 480vac,use a transformer with a 120vac secondary. F- F+ N vac Do not connect the input of the voltage regulator to DPE or auxiliary windings!! XR500B Universal Voltage Regulator Remote Voltage Adjustment 1w Note: It is not necessary to jumper 7 and 8 terminals if not using the Remote Voltage Adjustment! 3

4 Installation and setup 1. Install the regulator and wire up to the correct wiring diagram. 2. Turn the internal voltage control and stability control 15 or more turns counter clockwise (left). This procedure is necessary in case the original factory settings have been altered. Internal voltage adjustment Stability adjustment 3. If you are using a remote voltage adjustment, set it at 50% of adjustment. 4. Start up the prime mover and bring up to operating speed and turn on the regulator switch. (if used) 5. Set the internal voltage adjustment to the desired voltage setting for the generator output. If the generator voltage is unsteady or flickering, adjust the stability adjustment clockwise (right) until the voltage is steady and the green light is not pulsating. During this adjustment, be sure to keep the generator voltage within 10vac of the original setting with the internal voltage adjustment. 6. Place the generator on line and observe the frequency and voltage. 4

5 Application Troubleshooting Problem: Possible Cause No Voltage Pulsating Voltage Flickering Voltage High Voltage Voltage Drop on Load Low Voltage Poor Voltage Regulation No Voltage Control Possible Cause: 1. Residual input voltage to the voltage regulator is below 3.5vac or fuses are open in the regulator. 2. Unbalanced generator load. 3. Open exciter field or defective generator. 4. Stability adjustment is not properly adjusted. 5. Open diode in exciter or shorted rotor in generator. 6. Loose component in voltage regulator. 7. Loose wiring connections. 8. Input voltage to regulator is too low. 9. Exciter field is grounded. 10. Stability adjustment is set too far clockwise. 11. Exciter fields are reversed. 12. Wrong selection of regulator wiring configuration. 13. Defective voltage regulator. 14. SCR or Inverter drive effecting generator waveform. 15. Regulator needs external flashing circuit. 16. Isolation transformer is too small. 17. Isolation transformer is needed. 18. Exciter fields are not isolated from other circuits. 5

6 19. Input and field circuit are being fed by a common cable or conduit. 20. Incorrect hookup or wiring. Fuse Replacement Remove the 2 screws located on the front of the mounting can near the terminal board. Loosen the 2 screws located on the front of the mounting can near the voltage and stability adjustment holes. (DO NOT REMOVE!) Partially separate the top of the regulator printed circuit card from the mounting housing. (Separate just enough to reach and replace the fuses) Replace open fuses and re-tighten all screws. Fuse size is 20mm x 5mm, 5 250vac. (DO NOT REPLACE WITH ANY OTHER TYPE AND RATING OF FUSE! SEVERE DAMAGE AND PERSONAL INJURY COULD RESULT BY DOING SO!) 6

7 Installation form It is very important that you fill out this form completely when installing a voltage regulator. This form serves as a history record on the application. This form also contains the information needed by Power-Tronics, Inc., for repair and troubleshooting of any product you may be having problems with. Product Serial Number Date of Installation Other options Type of Generator Model # Brush type [ ] Brushless [ ] AC Stator Information Wired for Volts Phase Hz Generator Configuration: Lead Exciter/Rotor Information Exciter field resistance F+ / F- Ω Exciter field volts Slip Rings Ω Description of problem with product or generator Your phone number Your fax number Your address Name: Ship to Address: Ship to City, State, Zip: 7

8 PRODUCT WARRANTY Power-Tronics, Inc., assumes no liability for damages due to incorrect voltage or other voltage related damages resulting from either output of the generator or input to the generator exciter system. These problems should be protected with external devices provided by the customer such as fuses, surge suppressors, over/under voltage and frequency controls. Power-Tronics, Inc., warranties only parts and workmanship of this product for a period of 2 years from the original date of purchase from Power-Tronics, Inc. Under warranty, Power-Tronics, Inc. will replace, exchange or repair the defective product without labor or parts cost to the customer. Remaining warranty of the original product will be transferred to the replaced or repaired product. To obtain warranty, a copy of the original purchase receipt must be sent in with the defective product, which clearly shows the purchase date and serial number of the defective part. A repair request form must be sent in with the product before repairs will begin. You can obtain this form through contacting Power- Tronics, Inc.. Send repairs to: Power-Tronics, Inc., 2802 Cobbler Ln., Kerrville Texas USA Send in repairs only by UPS or FedEx. Any one of the following conditions will void the warranty:! Overheating of the power supply resistor on the printed circuit card.! Overheating of the SCR or freewheeling diode.! Physical damage to the printed circuit card, housing or components.! Unauthorized repair or alteration of printed circuit card.! Installation by anyone other than a qualified professional generator service technician.! Conductive or corrosive contamination of the circuit card.! Removal of our company identification from the product.! Removal of any conformal coating of the printed circuit card or components.! Overheating of foil on the printed circuit card.! Inappropriate or infeasible application! Use on any external device other than manufactured by Power-Tronics, Inc. No other warranty is expressed or implied. 8

9 Figure A Figure B Bench Check Instructions 1. Wire up the regulator as shown in figure A. 1. Connect up a 120 volt 50 to 150 watt light bulb to the F+ and F- Terminals. 2. Adjust the internal voltage and stability pots fully CCW (25 turns) or until a click is heard. 3. Input 120vac into the regulator at #1 and #2. (Fuse this input with fuses rated at 120 volts or higher and not more than 5 amps ac ) 4. Observation: The green status light should be on and the light bulb across F+ and F- should be off. If the green status light is not on, the internal fuses are blown in the regulator or there is internal damage to the regulator! If the green status light is not on, do not continue this test! 5. Turn the internal voltage adjustment CW until the light bulb across F+ and F- turns fully on, then adjust the internal voltage adjustment CCW until the light bulb is very dim. 6. Adjust the stability adjustment CW until the light bulb begins to brighten up. 7. Turn both of the internal voltage and stability pots fully CCW (25 turns ) or until a click is heard. 8. Remove the 120vac from the regulator. 9. Connect up the regulator in configuration B and perform all of the previous steps again. In this mode, the light bulb will only glow at half brilliance! 10. If you were able to successfully perform all of these tests, the regulator is good. 120 vac F+ F- 120 vac F- F+ 9

10 1Kva transformer for maximum output amperage vac 6 ohm, 100w Exciter field Unit / Parallel switch XR500B For stand-alone operation, close the Unit/Parallel switch. If the voltage raises during motor loading, reverse the current transformer leads. Remote voltage adjustment 100k, 1/2w 10

11 Parallel Connections For The XR500B Universal Voltage Regulator (Connection B) Generator xx/5a CT A B C 750va transformer for maximum output amperage. Regulator off/on 240vac Reactive droop adjustment 6 ohm, 100w Exciter field + - Unit / Parallel switch XR500B For stand-alone operation, close the Unit/Parallel switch. If the voltage raises during motor loading, reverse the current transformer leads. Remote voltage adjustment 100k, 1/2w 11

12 Parallel Connections for the XR500B Universal Voltage Regulator when used with the SE350 Static Exciter Module. xx/5 White CT ohm, 3 switch Regulator 4 100w 5 6 off/on transformer maximum amperage. switch. If the voltage raises during motor loading, reverse the adjustment adjustment 7 8 Generator AC1 240vac SE350 AC2 F+ F- Red XR500B A 5kva for output For current stand-alone transformer operation, leads. close Exciter the Unit/Parallel Gray field C B Reactive Unit / Parallel droop Remote 100k, voltage 1/2w 12

13 Parallel Connections for the XR500B Universal Voltage Regulator when used with the SE450 Static Exciter Module. Generator xx/5 CT A B C 5kva transformer for maximum output amperage. 240vac Exciter field Reactive droop adjustment 6 ohm, 100w Unit / Parallel switch AC1 AC2 F+ F- SE450 Gray Red White Regulator off/on XR500B For stand-alone operation, close the Unit/Parallel switch. If the voltage raises during motor loading, reverse the current transformer leads. Remote voltage adjustment 100k, 1/2w 13

14 Interpole on Diagram To Change From ARM Main Shunt Older Field Shunt Wound Voltage Voltage Regulation Regulator To Newer Solid State Voltage VR, UVR Rotor And XR Universal Voltage Regulators. F+ and F- F1 Original Wiring F2 Switch polarity if buildup Rheostat does not occur Or Voltage Regulator A1 ARM A2 C1 C2 Converted Wiring F1 F2 A1 A2 C1 C2 14

15 Optional AFM500X Auto Flash Connection Diagram AFM500X shown connected to an XR or UVR series Power-Tronics voltage regulator in the AUTO FLASH configuration. 1 XR500B XR500B UVR501 UVR UVR500 AFM500X shown connected to an XR or UVR series Power-Tronics voltage regulator in the BATTERY FLASH configuration XR500B XR500B-400 UVR501 UVR UVR500 B+ 12/24vdc 10Ω, 100w resistor PB switch, fuel or oil pressure, speed switch or relay contact. Note: Battery negative must be connected to the generator neutral and not to the F- of the exciter! 15