1999 Montero Sport 3.5/3.0L A/T PCM to 1997 Montero Sport 3.0L M/T ECM Harness Pin-Out Conversion Table
|
|
- Easter Fowler
- 6 years ago
- Views:
Transcription
1 999 Montero Sport 3.5/3.0L A/T PCM to 997 Montero Sport 3.0L M/T ECM Harness Pin-Out Conversion Table Pin-outs were taken directly from the official Mitsubishi factory service manuals and as such may contain errors if the service manual documentation is in error. Not all pin-outs may be listed in the tables below. Note that these pin-outs are untested and use of these tables may result in vehicle component damage. As such, the user of this documentation accepts all liability and may not hold the distributor of this document liable for any damages that may occur. Do not attempt to use these tables without confirming that the pin-outs are correct! 997 M/T ECM FED MD33839/MD (GREEN 76-pin) 999 A/T PCM FED MD35756/MD36453 (BLACK 9-pin) 999 A/T PCM -> 997 M/T Harness BLACK GREEN Lead 4 AWG 3 Description (male) (female) 6 No. fuel injector 9 6 No. 2 fuel injector No. 3 fuel injector No. 4 fuel injector No. 5 fuel injector No. 6 fuel injector 6 3 Heated oxygen sensor heater (front) FED EGR solenoid FED 6 Ignition power transistor unit A 0 2 Ignition power transistor unit B 23 3 Ignition power transistor unit C 4 Stepper motor coil <A> 4 28 Stepper motor coil <A2> 7 5 Stepper motor coil <B> 5 29 Stepper motor coil <B2> Evaporative emission purge solenoid 32 8 FLYLD Condenser fan relay input 9 Volume air flow sensor reset signal 9 20 Fuel pump relay module 8 2 A/C compressor clutch relay Service engine soon/malfunction indicator lamp Heated oxygen sensor heater (rear) FED Evaporative emission ventilation solenoid 4 46 Sensor supplied voltage 8 45 Crankshaft position sensor Engine coolant temperature sensor Spark check signal (RPM signal?) Power supply (ignition switch: "ON") Power supply & ignition switch-ig circuit (body GND #3, #0) Camshaft position sensor Barometric pressure sensor Power steering pressure switch 37 Lead?CM I/O NOTES B+ votage applied to pin 8 from condenser fan motor relay; when PCM switches on its power transistor, condenser fan motor relay coil is energized, causing current to flow in the circuit 4x4 Extreme Sports v.0 Page of 4
2 49 MFI relay (power supply) Backup power supply Volume air flow sensor Intake air temperature sensor 72 6 FLYLD A/C switch 2 input B+ (A/C load high) to v (A/C load low); 65.4 F B+ to pin 6 / 59 F 2v to pin 6; PCM receives signal from A/C automatic compressor-ecu (pin 9) and determines idle-up speed according to high/low air conditioning load 59 6 Ignition switch-st GND (body GND #3) 9 GND for M/T conversion 58 6 Ignition switch-st 7 7 Heated oxygen sensor (front) FED Heated oxygen sensor (rear) FED Throttle position sensor Closed throttle position switch <3.0L Engine> 87 retain the 3.0L throttle body, TPS, IAC, etc. 80 Vehicle speed sensor 86 output pulse detection 83 A/C switch Data link connector circuit (OBD connector pin 7) 62 data link connector () 84 Data link connector circuit (OBD connector pin ) 56 data link connector () 57 Volume air flow circuit, Baro Pressure Sensor, IAT Sensor, ECT 92 Sensor, TPS Sensor, O2 Sensor (front), O2 Sensor (rear), Evap Emission Control System Pressure Sensor, Closed throttle position switch, MAP Sensor, Fluid temp sensor <A/T>, Input shaft speed sensor <A/T>, Output shaft speed sensor <A/T> GND 9 Manifold differential pressure sensor Fuel tank differential pressure sensor Ignition switch-ig FLYLD A/T control relay output B+ to trigger-relay controling B+ power to pins 77/89 (#9) 75 Auto-cruise signal line system circuit output B+; auto-cruise control ecu (pin 3) overdrive cancel signal; this pin doesn't need to be wired to anything 77 FLYLD 4 Solenoid valve power supply input B+ applied to pins 77/89 through std 4 terminal relay; relay swiched on by pin 50 when IG switch turned on 89 FLYLD 6 76 FLYLD 6 Body GND (#3) 24" flying lead ring terminal 88 FLYLD 6 97 FLYLD 6 0 Park/Neutral position switch P input B+ applied to pin 0 when selector lever is in the Park range 02 Park/Neutral position switch D input B+ applied to pin 02 when selector lever is in the Drive range 03 FLYLD Input shaft speed sensor kω; insert 350 Ω,.5w resistor; loops back to PCM pin FLYLD Output shaft speed sensor kω; insert 250 Ω,.5w resistor; loops back to PCM pin FLYLD Second solenoid valve input 68 F Ω - insert appropriate resistor in harness; constant B+ applied to solenoid (pin 06 through terminal 9) 07 FLYLD Torque converter clutch solenoid valve input 68 F Ω - insert appropriate resistor in harness; constant B+ applied to solenoid (pin 07 through terminal 0) 08 Park/Neutral position switch R input B+ applied to pin 08 when selector lever is in the Reverse range 09 Park/Neutral position switch 3 input B+ applied to pin 09 when selector lever is in the 3rd range 0 Park/Neutral position switch L input B+ applied to pin 0 when selector lever is in the Low range 3 FLYLD Data link connector circuit (connector pin 26) data link connector (2) C-82 2-pin PCM flash pin 26 4 FLYLD Data link connector circuit (connector pin 27) data link connector (2) C-82 2-pin INVECS-II pin FLYLD Under drive solenoid valve input 68 F Ω - insert appropriate resistor in harness; constant B+ applied to solenoid (pin 20 through terminal 9) 2 FLYLD Park/neutral postion switch N / "N" range light system circuit 2 input B+ applied to pin 2 when selector lever is in the Neutral range; bulb resistance??? Ω - insert appropriate resistor or bulb in harness, tap lead with resistor, attach other end to Body GND (#9) 22 Park/neutral position switch 2 input B+ applied to pin 22 when selector lever is in the 2nd range 23 FLYLD 7 Stoplight switch input brake depressed, B+ applied to pin 23 4x4 Extreme Sports v.0 Page 2 of 4
3 24 FLYLD Fluid temperature sensor output 5v 32 F kω / 22 F kω; insert.kω,w resistor ( k Ω, V); loops back to PCM pin Transfer low detection switch output 4L continuity / other than 4L no continuity; this pin doesn't need to be wired to anything 26 Pattern select switch input Hold switch; B+ when switch on/no voltage with switch off; this pin doesn't need to be wired to anything 29 FLYLD Low-reverse solenoid valve input 68 F Ω - insert appropriate resistor in harness; constant B+ applied to solenoid (pin 29 through terminal 0) 30 FLYLD Overdrive solenoid valve input 68 F Ω - insert appropriate resistor in harness; constant B+ applied to solenoid (pin 30 through terminal 9) B+ applied to 77, 89, 06, 07, 20, 29, and 30 from A/T Control Relay 2 wire harness for selector lever in N; apply B+ 3 AWG mm unless otherwise noted, wire gauge is 20 AWG (0.5 mm 2 ) 4 FLYLD = flying lead (2" lengh unless otherwise noted) * confirm in manual ? A/T PCM -> 997 M/T Harness BLACK GREEN Lead AWG Description (male) (female) Lead?CM I/O NOTES 7 A/T fluid temperature warning light <V4A5> <A/T> 20 A/C compressor clutch relay 22 2 Fuel pump relay module 8 50 A/T Control Relay System GND <A/T> 5 Fuel temperature sensor (Fuel temperature sensor circuit) run wire from fuel level/temperature sensor pin <00-04 fuel temperature signal/sensor> 59 Park/neutral position switch <A/T> 9 60 Fuel gauge unit (Fuel level sensor circuit) tap from fuel gauge circuit <97-04 fuel level signal/sensor pin 2> 75 Auto-cruise signal line system circuit 76 GND 77 A/T Control Relay System (solenoid valve PS) <A/T> GND Fuel level warning light intercept fuel level warning light signal/sensor pin <97-99> 03 Input shaft speed sensor system <A/T> 04 Output shaft speed sensor system <A/T> 0 Park/Neutral Position Switch System (L) <A/T> 22 Park/Neutral Position Switch System (2) <A/T> 09 Park/Neutral Position Switch System (3) <A/T> 02 Park/Neutral Position Switch System (D) <A/T> 2 Park/Neutral Position Switch System (N) <A/T> 08 Park/Neutral Position Switch System (R) <A/T> 0 Park/Neutral Position Switch System (P) <A/T> 4x4 Extreme Sports v.0 Page 3 of 4
4 20 Low/Reverse solenoid system valve circuit (underdrive) <A/T> 06 Low/Reverse solenoid system valve circuit (second) <A/T> 30 Low/Reverse solenoid system valve circuit (overdrive) <A/T> 07 Low/Reverse solenoid system valve circuit (torque converter clutch) <A 29 Low/Reverse solenoid system valve circuit (low & reverse) <A/T> 23 Stoplight switch system circuit <A/T> 24 A/T fluid temperature sensor system circuit <A/T> 2 Transfer low detection switch <V4A5> <A/T> Immobilizer/PCM communications line PCM/immobilizer control module must come from same vehicle/additional parts and wiring required 4x4 Extreme Sports v.0 Page 4 of 4
5 A/T Fluid Temperature Sensor Circuit >>>> Pin 24.5mm 2 >>>>. kω, W resistor PCM PCM Plugs >>>> Pin 03.5mm 2 >>>> 350 Ω, 3 W resistor >>>> Pin 04.5mm 2 >>>> 250 Ω, 3 W resistor ECM Harness Plugs <<<< Pin 57 <<<< 4x4 Extreme Sports v.3 Page 5 of 4
6 A/C Switch 2 and Condenser Fan Control Circuit Flywheel Circuit >>>> Pin 50 >>>> GND #3 A/T Control Relay <<<< Pin 77 <<<< B+ Battery/5A Fuse PCM <<<< Pin 6.5mm 2 <<<< Thermal Switch Close 70ºF, Open 60ºF (+/-5 ) B+ IG Switch On < Zener N5350BG Diode N5404 > Flywheel Circuit <<<< Pin 8.5mm 2 <<<< Condenser Fan B+ Relay (nna) GND 4mm 2 B+ 4mm 2 Condenser Fan B+ Battery/nnA Fuse F068 (070 F-563 Close 70ºF, Open 60ºF (+/-5)) 2570F068 (090 F-664 Close by 90ºF max, Open by 80ºF min) 4x4 Extreme Sports v.6 Page 6 of 4
7 Alternate thermal switch setup PCM Pin 6 Temperature Switch Circuit on@65 F B+ GND B+ Kemo Electronic 2 V= Temperature switch Kit [B048] Operating voltage: 2 4V= Current consumption: approx. 00mA at maximum Temperature switching range: approx C Relay contact: x ON Contact capacity relay: max. 25V, 3A Board dimensions: approx. 54 x 27 mm 4x4 Extreme Sports v.6 Page 7 of 4
8 A/T Control Relay Diagram Flywheel Circuit < Diode N5404 Zener N5350BG > PCM <<<< Pin 77 2mm 2 <<<< <<<< Pin 89.25mm 2 <<<< >>>> Pin 50.5mm 2 >>>> A/T Control Relay (30A) GND #3.5mm 2 B+ 2.5mm 2 Battery/20A Fuse <<<< Pin 06 3Ω <<<< <<<< Pin 20 3Ω <<<< <<<< Pin 30 3Ω <<<< <<<< Pin 07 3Ω <<<< <<<< Pin 29 3Ω <<<< 2mm 2 2mm 2 2mm 2 2v, 3Ω, 50w resistor (4A per solenoid) PCM <<<< Pin 2 Park/Neutral SW Solenoids: Engine: Idling Gear range: Nst gear, engine idling B+ Selector lever position: Park 6-9v Pin 89, 06, 07, 20, 29, 30 tap off of 77 Resistor 06, 20, 30 in paralel Resistor 07, 29 in paralel 4x4 Extreme Sports v.8 Page 8 of 4
9 Park/Neutral Position Switch, Position "N" Flywheel Circuit PCM >>>> Pin 50 >>>> <<<< Pin 77 <<<< IG Switch On A/T Control Relay GND #3 B+ Battery/5A Fuse Pin 2 <<<<>>>> <<<< B+.5mm 2 <<<< B+.5mm 2 >>>> Combination Meter Neutral Bulb GND.5mm 2 Wire the PCM so 'transmission' is in constant Neutral Mitsu '99 Neutral guage cluster bulb, resistor n Ω, or LED Alternative Combination Meter Neutral Bulb Circuit 3mm LED with protective diodes and capacitor m/whiteled.html; Kingbright 3mm cylindrical LED Pin 2 <<<<>>>> >>>> B+ >>>> Resistor / R < Zenner N4732A Resistor / R2 LED > \\ GND Kingbright 00 Cylindrical LED , , r=300 ohm,.5w, Tol ±% d2=green, 2.2v, 25ma r2=00 ohm,.5w, Tol ±% d2=red, 2v, 30ma r2=00 ohm,.5w, Tol ±% d2=yellow, 2.v, 30ma r2=00 ohm,.5w, Tol ±% Example of a circuity that maintains a constant voltage across the LED as battery discharges to maintain constant brightness of LED. 4x4 Extreme Sports v.9 Page 9 of 4
10 On-Board Diagnostics (OBD) Flash <<<< Pin 3 PCM <<<< Phone/Audio 3.5mm Stereo Jack Phone/Audio 3.5mm Stereo Plug Openport 2.0 Mitsubishi Flash Plug PCM <<<< Pin 4 INVECS <<<< Phone/Audio 3.5mm Stereo Jack 4x4 Extreme Sports v0. Page 0 of 4
11 Transmission Input/Output Speed Sensors >>>> Pin 03.5mm 2 >>>> 350 Ω, 3 W resistor PCM >>>> Pin 04.5mm 2 >>>> >>>> Pin 24.5mm 2 >>>> 250 Ω, 3 W resistor. kω, W resistor ECM Harness Plugs <<<< Pin 57 <<<< output shaft speed* x current transmission gear ratio = input shaft speed* * speed = number of pulses 4x4 Extreme Sports v0. Page of 4
12 997 Mitsubishi Montero Sport 3.0L ECM M/T & A/T 4x4 Extreme Sports v0.4 Page 2 of 4
13 999 Mitsubishi Montero Sport 3.5L PCM A/T 4x4 Extreme Sports v0.4 Page 3 of 4
14 Wire Gauge Conversion Table No code indicates 0.5 mm2 American Wire Gauge Diameter (in) Diameter (mm) Cross Sectional Area (AWG) (mm2) AWG mm2 AWG mm2 AWG mm2 AWG mm / MCM MCM MCM / MCM / MCM / MCM 500 4x4 Extreme Sports v0.4 Page 4 of 4
Montero Sport L ECM/ L A/T PCM Pin-Out Table for Piggy-Back AEM F/IC 8 & Innovate LC-1 WBO M/T ECM & 1999 A/T PCM
Montero Sport 199 3.0L ECM/1999 3.5L A/T PCM Pin-Out Table for Piggy-Back AEM F/IC 8 & Innovate LC-1 WBO2 Pin-outs were taken directly from the official Mitsubishi factory service manuals and as such may
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Terminal side Wire side Component/circuit description ECM pin Signal Condition Typical value Oscilloscope setting (Suggested settings - Voltage/time per division)
More informationON-BOARD DIAGNOSTICS II SYSTEM. 5. Specified Data. Signal (V) Ignition SW ON (Engine OFF)
1. ENGINE CONTROL MODULE (ECM) I/O SIGNAL OBD0092A Crankshaft Camshaft Mass air flow Throttle Signal (+) 8 0 7 +7 Sensor output waveform Signal ( ) 29 0 0 Shield 54 0 0 Signal (+) 7 0 7 +7 Sensor output
More informationDiagnostic Trouble Codes (continued) GM Specific Codes
85 GM Specific Codes P11XX Fuel and Air Metering P1106 MAP Sensor Circuit Intermittent High Voltage P1107 MAP Sensor Circuit Intermittent Low Voltage P1108 BARO to MAP Signal Comparison Too High P1111
More informationA: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B
5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal
More informationEvoX EFI ECU Pinouts Last Updated Tuesday, 24 April :40
HOW TO: Reset your Fuel trims... Open your bonnet, open the fuse box, pull out 7.5A number 2 fuse, this is battery backup for your main ECU, remove for 2 seconds, and replace. Your fuel trims and learned
More informationPosition of Parts in Engine Compartment
[1UZ FE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor E 4 Engine Coolant Temp. Sensor (Water Temp. Sensor A 2 A/C Dual Pressure SW and A/C High Pressure SW (for Cooling Fan)) A
More informationDiagnostic Trouble Code (DTC) memory, checking and erasing
Page 1 of 49 01-12 Diagnostic Trouble Code (DTC) memory, checking and erasing Check DTC Memory (function 02) - Connect VAS5051 tester Page 01-7 and select vehicle system "01 - Engine electronics". Engine
More informationTROUBLESHOOTING FOR EFI ELECTRONIC CIRCUIT WITH VOLT/OHMMETER
FI118 TROUBLESHOOTING FOR EFI ELECTRONIC CIRCUIT WITH VOLT/OHMMETER HINT: Because the following troubleshooting procedures are designed for inspection of each separate system, the actual troubleshooting
More information5. Engine Control Module (ECM) I/O Signal S008526
5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen
More informationMULTIPOINT FUEL INJECTION (MPI) <4G9>
MULTIPOINT FUEL INJECTION (MPI) 13C-1 MULTIPOINT FUEL INJECTION (MPI) CONTENTS GENERAL................................. 2 Outline of Changes............................ 2 GENERAL INFORMATION...................
More informationLSx Harness Installation. lsxeverything.com #BecauseYouShould
LSx Harness Installation lsxeverything.com #BecauseYouShould Table of Contents Slide 1 Introduction Page Slide 2 Table of Contents Slide 3 Starting Instructions Slide 4 Power Connections Slide 5 Ground
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Name: Manufacturer: Ford Address: Model: Year: 1994 Registration: Tel - Private: Tel - Business: Mileage: Job number: Terminal side Wire side Component/circuit description
More informationTroubleshooting Self-diagnostic Procedures
Self-diagnostic Procedures I. When the Malfunction Indicator Lamp (MIL) has been reported on, do the following: 1. Connect the Service Check Connector terminals with a jumper wire as shown. (The 2P Service
More informationG - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.
More informationPosition of Parts in Engine Compartment
ELECTRICAL WIRING ROUTING [3S GTE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor D 1 Date Link Connector 1 (Check Connector) A 2 A/C Condenser Fan Motor D 2 Distributor A 4 A/C Magnetic
More informationService Bulletin. DTC Detection Item Associated Monitor
Service Bulletin 03-010 Applies To: All OBD II equipped models except SLX March 29, 2003 OBD II DTCs and Their Associated Monitors This is a list of all DTCs for all OBD II models. No one model has all
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: K143 AC compressor clutch relay X88 AC connector S63 AC refrigerant pressure switch S341 AC refrigerant triple pressure switch A16 Anti-lock braking system (ABS) control
More informationMULTIPORT FUEL SYSTEM (MFI) <2.4L ENGINE>
13A-1 GROUP 13A MULTIPORT FUEL SYSTEM (MFI) CONTENTS GENERAL DESCRIPTION......... 13A-2 FUEL INJECTION CONTROL...... 13A-5 THROTTLE VALVE OPENING ANGLE CONTROL..................... 13A-6
More informationGROUP 13Ab. 13Ab-2 CONTENTS TROUBLESHOOTING STRATEGY.. DATA LIST REFERENCE TABLE... 13Ab-29 TROUBLE CODE DIAGNOSIS...
13Ab-1 GROUP 13Ab CONTENTS TROUBLESHOOTING STRATEGY.. 13Ab-2 DATA LIST REFERENCE TABLE... 13Ab-29 TROUBLE CODE DIAGNOSIS..... 13Ab-2 FAIL-SAFE FUNCTION REFERENCE TABLE........................ 13Ab-20 DIAGNOSTIC
More informationGROUP 17 CONTENTS WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
17-1 GROUP 17 CONTENTS ENGINE CONTROL 17-4 GENERAL DESCRIPTION 17-4 ENGINE CONTROL SYSTEM DIAGNOSIS 17-4 INTRODUCTION TO ENGINE CONTROL SYSTEM DIAGNOSIS 17-4 ENGINE CONTROL SYSTEM DIAGNOSTIC TROUBLESHOOTING
More informationG ELECTRICAL WIRING ROUTING
2 6 G ELECTRICAL WIRING ROUTING [2JZ-GTE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp Sensor A 2 A/C Condensor Fan Motor A 3 A/C Triple Pressure SW (A/C Dual and Single Pressure SW) A
More informationHOT IN START OR RUN JUNCTION BLOCK (BEHIND LEFT SIDE OF DASH)
of //0 : PM Vehicle Reference: WIRING DIAGRAMS BODY CONTROL MODULES 00 Mitsubishi Diamante.L Eng VR-X Fig : Assist ECU Circuit HOT IN START OR RUN (BEHIND (ON LEFT FRONT FENDER) HOT IN ACC OR RUN (BEHIND
More informationENGINE 01 02A 1. Toc of SCT ON-BOARD DIAGNOSTIC [ENGINE. Toc of SCT 01 02A ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (ZM)] 01 02A
ENGINE 01 SECTION Toc of SCT ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (ZM)]...01-02A ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (FS)]...01-02B ON-BOARD DIAGNOSTIC [CRUISE CONTROL SYSTEM].......01-02C
More informationDiagnostic Trouble Code (DTC) table
Page 1 of 40 01-19 Diagnostic Trouble Code (DTC) table Note: When malfunctions occur in monitored sensors or components, Diagnostic Trouble Codes (DTCs) are stored in DTC memory with a description of the
More information3/14/2018 Engine Controls (Powertrain Management) - ALLDATA
//0 Engine Controls (Powertrain Management) - ALLDATA 00 Chrysler Truck PT Cruiser L-.L VIN X Vehicle > Powertrain Management > Diagrams > Electrical - Interactive Color (Non OE) Engine Controls - Page
More informationPowertrain DTC Summaries EOBD
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar X-TYPE 2.0 L 2002.25 Model Year Refer to page 2 for important information regarding the use of Powertrain DTC Summaries. Jaguar X-TYPE 2.0
More information1. Connect the Honda PGM Tester or an OBD II scan tool to the 16P Data Link Connector (DLC) located behind the right side of the center console.
Troubleshooting Procedures I. How To Begin Troubleshooting When the Malfunction indicator Lamp (MIL) has been reported on, or there is a driveability problem, use the appropriate procedure below to diagnose
More informationMotronic September 1998
The Motronic 1.8 engine management system was introduced with the 1992 Volvo 960. The primary difference between this Motronic system and the previous generation of Volvo LH-Jetronic engine management
More informationEngine management/transmission
MAZDA Model: 323 (BG) 323 Estate 1,6/4x4 (BW) 323 (BA/BJ) 626/MX-6 626/Estate Xedos 6/9 MX-3/MX-5 Year: 1989-00 Engina code: BP, BP-DOHC, B3, B3E, B6, B6-SOHC, B6-DOHC, B6E,FP, FS, KF, KJ, KL K8, RF, RF-CX,
More informationFor Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID
Index For Troubleshooting of DTC related components, see chart on page 11-53. '96-99 models: EXHAUST GAS RECIRCULATION (EGR) and LIFT MANIFOLD ABSOLUTE PRESSURE (MAP) INTAKE AIR BYPASS (IAB) HIGH page
More informationDTC Summaries. NipponDenso V12 Engine Management
DTC Summaries NipponDenso V12 Engine Management OBD II MONITORING CONDITIONS: When testing for DTC reoccurrence, it can be determined if the Service Drive Cycle was of sufficient length by performing a
More information13A-1 FUEL CONTENTS MULTIPOINT FUEL INJECTION (MPI) FUEL SUPPLY... 13B
13A-1 FUEL CONTENTS MULTIPOINT FUEL INJECTION (MPI)... 13A FUEL SUPPLY... 13B 13A-2 MULTIPOINT FUEL INJECTION (MPI) CONTENTS GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 6 SEALANT... 6 SPECIAL TOOLS...
More informationGROUP 13Ab. 13Ab-2 CONTENTS TROUBLESHOOTING STRATEGY.. DATA LIST REFERENCE TABLE... 13Ab-28 TROUBLE CODE DIAGNOSIS...
13Ab-1 GROUP 13Ab CONTENTS TROUBLESHOOTING STRATEGY.. 13Ab-2 DATA LIST REFERENCE TABLE... 13Ab-28 TROUBLE CODE DIAGNOSIS..... 13Ab-2 FAIL-SAFE/BACKUP FUNCTION TABLE........................ 13Ab-20 DIAGNOSTIC
More informationPosition of Parts in Engine Compartment
ELECTRICAL WIRING ROUTING [5S FE] Position of Parts in Engine Compartment A 1 A/C Condenser Fan Motor E 4 Engine Coolant Temp. Sensor (EFI Water Temp. A 2 A/C Magnetic Clutch and Lock Sensor Sensor) A
More informationPowertrain DTC Summaries EOBD
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar S-TYPE V6, V8 N/A and V8 SC 2002.5 Model Year Refer to pages 2 9 for important information regarding the use of Powertrain DTC Summaries.
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More information2002 ENGINE PERFORMANCE. Self-Diagnostics - RAV4. Before performing testing procedures, check for any related Technical Service Bulletins (TSBs).
2002 ENGINE PERFORMANCE Self-Diagnostics - RAV4 INTRODUCTION NOTE: Before performing testing procedures, check for any related Technical Service Bulletins (TSBs). To properly diagnosis and repair this
More informationCONFIGURATION DIAGRAMS
80-1 GROUP 80 CONFIGURATION DIAGRAMS CONTENTS CONFIGURATION DIAGRAMS......................... 80A SPLICE LOCATIONS................................. 80B 80A-2 GROUP 80A CONFIGURATION DIAGRAMS CONTENTS OVERALL
More informationG ELECTRICAL WIRING ROUTING [5VZ FE] TOYOTA TACOMA (EWD517U) Position of Parts in Engine Compartment
G ELECTRICAL WIRING ROUTING [5VZ FE] Position of Parts in Engine Compartment A 5 A/C Magnetic Clutch A 7 A/T Oil Temp. Sensor A22 ABS Actuator with ECU A23 Air Fuel Ratio Sensor (Bank 1 Sensor 1) A24 ADD
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationDIAGNOSTIC TROUBLE CODE DEFINITIONS
DIAGNOSTIC TROUBLE CODE DEFINITIONS DIAGNOSTIC TROUBLE CODE DEFINITIONS DTC Description P0010 Variable Valve Timing Circuit Malfunction (Bank 1) P0020 Variable Valve Timing Circuit Malfunction (Bank 2)
More information5. Engine Control Module (ECM) I/O Signal
5. Engine Control Module (ECM) I/O Signal A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9
More informationDiagnostic Trouble Code (DTC) List - Vehicle
Document ID# 850406 2002 Pontiac Firebird Diagnostic Trouble Code (DTC) List - Vehicle DTC DTC 021 and/or 031 DTC 022 and/or 032 DTC 023 or 033 DTC 24/34 DTC 025 and/or 035 DTC 041 DTC 042 DTC 043 DTC
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationENGINE AND EMISSION CONTROL
17-1 GROUP 17 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL.......... 17-3 GENERAL DESCRIPTION...... 17-3 ENGINE CONTROL SYSTEM DIAGNOSIS.................. 17-3 INTRODUCTION TO ENGINE CONTROL SYSTEM
More informationMULTIPORT FUEL SYSTEM (MFI) <3.8L ENGINE>
13B-1 GROUP 13B MULTIPORT FUEL SYSTEM (MFI) CONTENTS GENERAL DESCRIPTION......... 13B-2....................... 13B-5 ACTUATOR.................... 13B-5 FUEL INJECTION CONTROL...... 13B-7
More information01 02B ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (FS)]
ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (FS)] CONTROL SYSTEM WIRING DIAGRAM [FS]............................ 2 CONTROL SYSTEM DEVICE AND CONTROL RELATIONSHIP CHART [FS]........ 4 Engine Control System............
More informationTROUBLE DIAGNOSIS. ECM Harness Connector Terminal Layout. ECM Terminals and Reference Value EC-107
ECM Harness Connector Terminal Layout UBS00K1I A EC C ECM Terminals and Reference Value PREPARATION 1. ECM is located behind the glove box. For this inspection, remove glove box. 2. Remove ECM harness
More informationPowertrain DTC Summaries EOBD
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar X-TYPE 2.5L and 3.0L 2001.5 Model Year Revised January, 2002: P0706, P0731, P0732, P0733, P0734, P0735, P0740, P1780 POSSIBLE CAUSES Revised
More informationCONFIGURATION DIAGRAMS
80A-1 GROUP 80A CONFIGURATION DIAGRAMS CONTENTS OVERALL CONFIGURATION DIAGRAM...................... 80A-2 HOW TO READ CONFIGURATION DIAGRAMS.................... 80A-3 ENGINE COMPARTMENT......... 80A-4
More informationMULTIPORT FUEL SYSTEM (MFI) <2.4L ENGINE>
13B-1 GROUP 13B MULTIPORT FUEL SYSTEM (MFI) CONTENTS GENERAL DESCRIPTION 13B-2 CONTROL UNIT 13B-5 SENSOR 13B-7 ACTUATOR 13B-24 FUEL INJECTION CONTROL 13B-31 IGNITION TIMING AND CONTROL FOR
More informationNissan Altima ECU
by jserrano (www.nissanclub.com) 1993-1994 Nissan Altima ECU Pin Color Name Symbol Description Signal Rev. 0.2 1 W Ignition Signal IGN This pulse signal drives the base of the ignition power transistor
More informationFig.11 Powertrain Control Module (PCM)
2003 Dodge or Ram Truck Caravan V6-3.3L VIN R Vehicle > Powertrain Management > Relays and Modules - Powertrain Management > Relays and Modules - Computers and Control Systems > Engine Control Module >
More informationDIAGNOSTIC TROUBLE CODE CHART HINT:
DIAGNOSTICS DIAGNOSTIC TROUBLE CODE CHART HINT: SFI SYSTEM (1MZFE) 05241 Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument or other factors. If a
More informationPOWER SOURCE (Current Flow Chart)
POWER SOURCE (Current Flow Chart) The chart below shows the route by which current flows from the battery to each electrical source (Fusible Link, Circuit Breaker, Fuse, etc.) and other parts. The next
More informationPGM-FI ( Models)
PGM-FI ( 00-0 Models) HOT AT ALL TIMES HOT IN ON OR START FUSE BACK UP, (RADIO).5A FUSE FI E/M 5A C PHOTO UNDER- HOOD FUSE/ RELAY PHOTO FUSE FUEL PUMP (SRS UNIT) 5A page 0-. UNDER- DASH FUSE/ RELAY PHOTO
More informationENGINE AND EMISSION CONTROL
17-1 GROUP 17 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL 17-2 GENERAL INFORMATION 17-2 AUTO-CRUISE CONTROL SYSTEM 17-3 GENERAL INFORMATION 17-3 CONSTRUCTION AND OPERATION 17-5 17-7 GENERAL INFORMATION
More informationDTC P0172 Fuel Trim System Rich
Page 1 of 6 1997 Chevrolet Cavalier Cavalier, Sunfire (VIN J) Service Manual Document ID: 47788 DTC P0172 Fuel Trim System Rich System Description A Closed Loop air/fuel metering system is used to provide
More informationMULTIPORT FUEL SYSTEM (MFI)
13A-1 GROUP 13A CONTENTS GENERAL INFORMATION...13A-2 CONTROL UNIT...13A-7 SENSOR...13A-9 ACTUATOR...13A-26 FUEL INJECTION CONTROL...13A-31 IGNITION TIMING AND CONTROL FOR CURRENT CARRYING TIME...13A-36
More information1995 Nissan Altima ECU
by jserrano (www.nissanclub.com) 1995 Nissan Altima ECU Pin Color Name Symbol Description Signal Rev. 0.6 1 W Ignition Signal IGN This pulse signal drives the base of the ignition power transistor and
More informationCONFIGURATION DIAGRAMS
80A-1 GROUP 80A CONFIGURATION DIAGRAMS CONTENTS OVERALL CONFIGURATION DIAGRAM...................... 80A-2 HOW TO READ CONFIGURATION DIAGRAMS.................... 80A-3 ENGINE COMPARTMENT......... 80A-4
More informationENGINE (DIAGNOSTICS) EN(SOHC)
EN(SOHC) Page 1. Basic Diagnostic Procedure...2 2. Check List for Interview...4 3. General Description...6 4. Electrical Components Location...9 5. Engine Control Module (ECM) I/O Signal...22 6. Engine
More informationPowertrain DTC Summaries OBD II
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar X-TYPE 2.5L and 3.0L 2002 Model Year Revised January, 2002: P0706, P0731, P0732, P0733, P0734, P0735, P0740, P1780 POSSIBLE CAUSES Revised
More informationMULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-1 GROUP 13B MULTIPORT FUEL INJECTION (MFI) CONTENTS GENERAL INFORMATION 13B-3 GENERAL SPECIFICATIONS 13B-6 SERVICE SPECIFICATIONS 13B-7 SEALANT AND ADHESIVE 13B-7 SPECIAL TOOL 13B-8 MULTIPORT
More information2009 Model year NPR, NPR HD Gas Electrical Symbols. Symbol Meaning Symbol Meaning Symbol Meaning
2009 Model year NPR, NPR HD Gas Electrical Symbols 14.1 Symbol Meaning Symbol Meaning Symbol Meaning Fuse Electronic Parts Coil (Inductor), Solenoid Magnetic Valve Fusible Link Resistor Relay Fusible Link
More informationTroubleCodes.net- engine & OBD2 Trouble Codes and Technical info & Tool Store.
Page 1 sur 8 advertisement Articles / SAFETY / TOOL STORE!! / BAT Support / Search / Help / Guestbook / About Us / Contact Us Forums Navigation Links & Technical Trouble Codes Sunday, January 23, 2005
More informationDisconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
More informationFUEL 13-1 CONTENTS MULTIPOINT INJECTION (MPI)... 2 GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 3 SEALANT... 3 SPECIAL TOOLS...
13-1 FUEL CONTENTS MULTIPOINT INJECTION (MPI)....... 2 GENERAL INFORMATION................ 2 SERVICE SPECIFICATIONS.............. 3 SEALANT............................... 3 SPECIAL TOOLS........................
More information3. Engine Control System Diagram
ENGINE - 2UZ-FE ENGINE 59 3. Engine Control System Diagram Ignition Switch Fuel Pump Relay Fuel Pump Resister Circuit Opening Fuel Relay Filter Intake Temp. Mass Air Flow Meter Throttle Position Fuel Pump
More informationFive-digit error code First position: P - is for powertrain codes B - is for body codes C - is for chassis codes
https://www.automotive-manuals.net Five-digit error code First position: P - is for powertrain codes B - is for body codes C - is for chassis codes The second position: 0 - the total for the OBD-II code
More informationBUZZERS, RELAYS & TIMERS
BUZZERS, RELAYS & TIMERS 1997 MAZDA MX-5 Miata BUZZERS, RELAYS & TIMERS Location A/C Relay In right front of engine compartment, near radiator. See Fig. 1. Condenser Fan Relay In right front of engine
More information1996 Nissan Altima ECU
by jserrano (www.nissanclub.com) 1996 Nissan Altima ECU Pin Color Name Symbol Description Signal Rev. 0.5 1 W Ignition Signal IGN This pulse signal drives the base of the ignition power transistor and
More informationENGINE CONTROL SECTION EC CONTENTS
ENGINE CONTROL SECTION EC CONTENTS PRECAUTIONS... EC-3 On Board Diagnostic (OBD) System of Engine... EC-3 Precaution... EC-3 PREPARATION... EC-6 Special Service Tools... EC-6 DESCRIPTION... EC-7 Description...
More informationG ELECTRICAL WIRING ROUTING
G ELECTRICAL WIRING ROUTING Position of Parts in Engine Compartment A 1 A/C Condenser Fan Motor A 2 A/C Magnetic Clutch and Lock Sensor A 3 A/C Triple Pressure SW (A/C Dual and Signal Pressure SW) A 4
More information5. Engine Control Module (ECM) I/O Signal
5. A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 35 34 33 32 31
More information3/25 Switch, power sunroof 3/26 Control module, driver's seat 3/27 Control module, passenger's seat 3/28 Switch for heated driver's seat 3/29 Switch
List of Components 1/1 Battery 2/1 Headlight relay with bulb failure sensor 2/2 Foglight relay 2/3 Regulator DIM-DIP 2/4 Intermittent wiper relay, windshield wipers 2/5 Relay, seat belt reminder/ignition
More informationG ELECTRICAL WIRING ROUTING [1MZ-FE] Position of Parts in Engine Compartment
G ELECTRICAL WIRING ROUTING [1MZ-FE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor A 2 A/C Condenser Fan Motor A 3 A/C Magnetic Clutch and Lock Sensor A 4 A/C Triple Pressure SW
More informationLotus Service Notes Section EMD
ENGINE MANAGEMENT SECTION EMD Lotus Techcentre Sub-Section Page Diagnostic Trouble Code List EMD.1 3 Component Function EMD.2 8 Component Location EMD.3 10 Diagnostic Guide EMD.4 11 CAN Bus Diagnostics;
More information20-pin ECU Technical Specs. Engine Control Unit. (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
Engine Control Unit (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product: Part#:
More informationSOUL GDI REPAIR AND MAINTENANCE
SOUL 2013-1.6 GDI REPAIR AND MAINTENANCE (First Numbers are page number within section - Numbers in parenthesis are overall document page) GENERAL INFORMATION (23 PAGES) 01-07 (01-07): Identification Number
More informationC6 Corvette DIC Codes
C6 Corvette DIC Codes B0159 Outside Air Temp Sensor B2910 Steering Column Lock Password Incorrect B0164 Pass Compartment Temp Sensor B2981 Right Front Door Handle Switch B0174 Output Air Temp Sensor 1
More informationCIRCUIT DIAGRAMS GROUP CONTENTS HOW TO READ CIRCUIT DIAGRAMS BACKUP LIGHT TURN SIGNAL LIGHT AND HAZARD WARNING LIGHT...
90-1 GROUP 90 CIRCUIT DIAGRAMS CONTENTS HOW TO READ CIRCUIT DIAGRAMS................................. 90-4 JUNCTION BLOCK.............. 90-10............. 90-12 CENTRALIZED JUNCTION........ 90-18 POWER
More information4.0L CEC SYSTEM Jeep Cherokee DESCRIPTION OPERATION FUEL CONTROL DATA SENSORS & SWITCHES
4.0L CEC SYSTEM 1988 Jeep Cherokee 1988 COMPUTERIZED ENGINE Controls ENGINE CONTROL SYSTEM JEEP 4.0L MPFI 6-CYLINDER Cherokee, Comanche & Wagoneer DESCRIPTION The 4.0L engine control system controls engine
More informationhttp://www.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=t... Page of // 0 Chevrolet Traverse.L Eng LT Service Manual: WIRING DIAGRAMS Print Date: // ENGINE PERFORMANCE >.L VIN D Fig
More informationFUEL INJECTION SYSTEM - MULTI-POINT
FUEL INJECTION SYSTEM - MULTI-POINT 1988 Jeep Cherokee 1988 Electronic Fuel Injection JEEP MULTI-POINT 4.0L Cherokee, Comanche, Wagoneer DESCRIPTION The Multi-Point Electronic Fuel Injection (EFI) system
More information3/22 Switch for rear power window lifts 3/23 Switch for power door mirror, driver's side 3/24 Switch for power door mirror, passenger's side 3/25
List of Components 1/1 Battery 2/2 Relay, front foglights USA/CDN 2/3 Regulator DIM-DIP 2/4 Intermittent relay, windshield wipers 2/5 Relay, seat belt reminder/ignition key warning 2/6 Bypass relay 151
More informationDIAGNOSIS SYSTEM DESCRIPTION EG2 170
EG2170 DIAGNOSIS SYSTEM DESCRIPTION The ECM contains a builtin self diagnosis system by which troubles with the engine signal network are detected and a malfunction indicator lamp on the combination meter
More informationSECONDARY PARAMETERS AND ENABLE CONDITIONS
SECONDARY S AND Manifold Pressure Sensor Rationality Manifold Pressure Too Low Manifold Pressure Too High Intake Air Temperature Sensor Shorted Intake Air Temperature Sensor Open Coolant Temperature Sensor
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationDiagnostic Trouble Code (DTC) Root Cause. for Omnitek ECM 64A/66A/88A. & Remedial Action
Diagnostic Trouble Code (DTC) Root Cause & Remedial Action for Omnitek ECM 64A/66A/88A Omnitek Engineering Corp. 1945 S Rancho Santa Fe Rd. San Marcos, CA 92078 Tel. 760-591-0089 - Fax. 760-591-0880 -
More informationENGINE CONTROL (2RZ FE)
ENGINE CONTROL (RZ FE) IF (A/T) AM IG 6 FROM POER SOURCE SYSTEM (SEE PAGE 44) AM ACC IG ST IF. A STA F FUSE O. A IGN A EFI 0A OD A STOP I4 IGNITION S (A/T) (A/T) F 0 (M/T) Y Y V (A/T) IK3 (A/T) (M/T) 3
More informationData Unit Value Coolant temperature 0.436V (130 ) ~4.896V (-40 )
149000 153 1. ENGINE DATA LIST Data Unit Value Coolant temperature 0.436V (130 ) ~4.896V (40 ) Intake air temperature 40~130 (varies according to ambient air temperature or engine mode) Idle speed rpm
More informationTruck and Transport IP Red Seal Practice Exam PRACTICE EXAM 4
Truck and Transport IP Red Seal Practice Exam PRACTICE EXAM 4 1. Which of these sensors directly measures engine load? a. Manifold absolute pressure sensor. b. Coolant sensor (ECT). c. Vehicle speed sensor.
More information2003 RSX - Intake Manifold Removal and Installation
2003 RSX - Intake Manifold Removal and Installation Exploded View - K20A3 Engine Removal - K20A3 Engine 1. Remove the intake manifold cover. 2. Disconnect the intake air temperature (IAT) sensor connector
More informationDIAGNOSTIC TROUBLE CODE CHART
DI158 DIAGNOSTIC TROUBLE CODE CHART HINT: ENGINE (2JZGTE) Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument or other factors. If a malfunction code
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Name: Manufacturer: Ford Address: Model: Scorpio Year: 1991 Registration: Tel - Private: Tel - Business: Mileage: Job number: Terminal side Wire side Component/circuit
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More informationAcura Plus Comprehensive & Major Component Coverage
Acura Plus Comprehensive & Major Component Coverage ENGINE Cylinder block and all internal parts Cylinder heads and all internal parts Engine mounts Engine seals and gaskets Flywheel Intake and exhaust
More informationPOWER SOURCE (Current Flow Chart)
The chart below shows the route by which current flows from the battery to each electrical source (Fusible Link, Circuit Breaker, Fuse, etc.) and other parts. The next page and following pages show the
More information