Model PH87 Retraction Sensor Assembly

Transcription

1 Instruction Manual Model PH87 Retraction Sensor Assembly Yokogawa Corporation of America 2 Dart Road, Newnan, Georgia U.S.A Tel: Fax: Doc. Nr. L2528 January rd edition

2 2 TABLE OF CONTENTS Overview... 3 Assembly Instructions-Stage # Assembly Installation Instructions- with /B ball valve option... 8 In-Service Installation-with /B ball valve option Sensor Service Sensor Replacement Exploded View of PH Part Numbers and Descriptions PH87 Dimensions and Clearance Requirements... 18

3 3 Sensor Installation Overview NOTE: THE FOLLOWING INFORMATION IS INTENDED TO PROVIDE THE USER WITH A PREVIEW OF WHAT WILL BE REQUIRED TO INSTALL THE MODEL PH87 SENSOR ASSEMBLY. PLEASE REVIEW THE DIAGRAM AND GUIDELINES BEFORE PROCEEDING. Typical Sensor Installation Diagram Shown with Optional /B Ball Valve ASSEMBLY ph/orp SENSOR Sensor Installation Guidelines: [1]. Install the model PH97 sensor in pipe or vessel between 15 and 90 from horizontal. [2]. Connect flex conduit with adequate service loop to junction box. [3]. Connect the sensor cable to the terminals inside the junction box. [4]. Keep cable run between junction box and ph / ORP instrument as short as possible.

4 4 Sensor Assembly Instructions-Stage1 Begin stage #1 Assembly of the model PH87 by following the step-by-step instructions [A] through [F] in order as shown below: [Step B]. slide packing gland, item no.3, onto sheath, item no.4. keep locking nut and ferrules loose but attached to packing gland [Step A]. Install packing gland o-ring, item no. 3d, into packing gland body, item no. 3c. [Step F]. Thread sensor cable through coupler tube, item no. 1, then slide coupler tube into sheath until it contacts sensor. [Step E]. Stretch o-ring, item no. 1a, into groove on coupler tube, item no. 1. [Step D]. Thread Sensor Cable through sheath and slide the sensor into sheath until it stops against flared end Flared end of sheath [Step C]. stretch o-rings, item no. 2, into grooves on sensor PLEASE NOTE REFER to pages 16 and 17 of the sensor assembly and itemized part REFER TO PAGES 15 AND 16 OF THE list for all SENSOR these ASSEMBLY components AND ITEMIZED PART LIST FOR ALL THESE COMPONENTS.

5 Sensor Assembly ly Instructions-Stage1 Instructions Stage1 (Continued) 5 [Step G]. Thread sensor cable through coupler tube, item no. 1, then slide coupler tube into sheath until it contacts sensor. the coupler tube and sensor should be threaded together until both are seated against the ends of the sheath,

6 6 Sensor Assembly Instructions-Stage1 (Continued) [Step H]. REMOVE JUNCTION BOX COVER AND THERAD SENSOR CABLE THROUGH [Step H]. JUNCTION REMOVE BOX ASSEMBLY (JUNCTION JUNCTION BOX BOX AND COVER PROVIDED AND THERAD SENSOR CABLE THROUGH PIPE NIPPLE). THREAD JUNCTION JUNCTION BOX ASSEMBLY BOX ASSEMBLY PIPE NIPPLE INTO (JUNCTION BOX AND PROVIDED SENSOR PIPE NIPPLE). COUPLER THREAD ASSEMBLY, JUNCTION ITEM BOX NO. ASSEMBLY 1.INSTALL PIPE SUITABLE NIPPLE FLEX INTO CONDUIT SENSOR LONG COUPLER ENOUGH ASSEMBLY, TO ALLOW FOR ITEM SERVICING NO. 1.INSTALL OR REPLACEMENT SUITABLE FLEX OF CONDUIT SENSOR. LONG ENOUGH TO ALLOW FOR SERVICING OR REPLACEMENT OF SENSOR. [Step I]. CONNECT THE SENSOR WIRES TO THE 5-TERMINAL STRIP IN THE [Step JUNCTION I]. CONNECT BOX IN THE THE SENSOR FOLLOWING WIRES TO ORDER. THE 5-TERMINAL THE RED TC STRIP WIRE IN THE JUNCTION BOX IN THE FOL- CONNECTS TO TERMINAL #1 AND LOWING ORDER. THE RED TC WIRE THE BLACK TC WIRE TO TERMINAL CONNECTS TO TERMINAL #1 AND #2. THE CONNECT BLACK THE TC WIRE SENSOR TO TERMINAL REFERENCE #2. CONNECT (BLACK) THE TO SENSOR #3, REFER- THE ENCE SOLUTION (BLACK) GROUND TO #3, THE (GREEN) SOLUTION TO GROUND TERMINAL (GREEN) #4 AND TO ph TERMINAL (CLEAR) TO #4 TERMINAL AND ph #5. (CLEAR) THREAD TO THE TERMINAL EXTENSION #5. CABLE THREAD THROUGH THE EXTENSION CONDUIT. ATTACH CABLE THE THROUGH LABELED CONDUIT. WIRES TO ATTACH THE THE TERMINALS LABELED IN WIRES THE SAME TO THE ORDER TERMINALS AS THE IN SENSOR THE SAME WIRES ORDER LISTED AS THE ABOVE. SEN- REPLACE SOR WIRES THE JUNCTION LISTED ABOVE. BOX COVER. SLIDE- THE PROTECTIVE INSULTING BOOT OVER CONNECTORS AND REPLACE THE JUNCTION BOX COVER.

7 7 Sensor Assembly Instructions-Stage1 (Continued) The stage #1 assembly of the ph97 sensor is now complete and should appear as one of the two assemblies shown below Standard STANDARD Assembly ASSEMBLY [STEp J]. Perform a 2-point calibration with ph buffer solutions before proceeding further with the assembly and installation. Note: refer to ph 97 sensor instructions for wiring and calibration procedures. NOTE: REFER TO PH 97 SENSOR INSTRUCTIONS FOR WIRING AND CALIBRATION PROCEDURES.

8 8 Sensor Assembly Instructions-/B Ball Valve Option Begin assembly of the /B ball valve option for model PH87 sensor by following the step-by-step instructions [a] through [d] in order as shown below: PLEASE NOTE REFER to pages 16 and 17 of the REFER sensor TO PAGES assembly 15 AND and 16 OF itemized THE SENSOR ASSEMBLY AND ITEMIZED PART part list for all these LIST FOR ALL THESE COMPONENTS. components [Step a]. Thread the reducer bushing, item no.6, using teflon tape to seal and tighten in place [Step D]. Insure that the valve is in the closed postion as shown below before proceeding to next step. [Step B]. Thread the Nipple, item no.7, into ball valve, item no.6, using teflon tape to seal and tighten in place [Step C]. Thread the Nipple, item no.7, Along with ball valve, item no.6, and reducer bushing, item no.5, into weldalet or appropriate process fitting. use teflon tape to seal threads and tighten in place PLEASE NOTE: /B OPTION IS REQUIRED (OR CUSTOMER SUPPLIED BALL VALUE IS REQUIRED) FOR RETRACTION OF PH87 WHILE PROCESS IS UNDER PRESSURE

9 9 Sensor Assembly Installation Instructions-/B Ball Valve (Continued) Complete /B ball valve option assembly of the model PH87 By following the step-by-step instructions [e] and [f] in order as shown below: [Step E]. Apply teflon tape to pipe threads of packing gland fitting and slide fitting to sensor end of sheath. install stage #1 subassembly into valve taking care not to force the sensor into the ball portion of the valve to prevent breakage of the glass bulb. [Step F]. Securely Tighten packing gland fitting into valve assembly to provide a proper seal. THE ASSEMBLY OF THE THE SENSOR ASSEMBLY IS NOW OF THE COMPL PH87 SENSOR AND SHOULD IS NOW COMPLETE APPEAR A AND SHOWN. SHOULD DO APPEAR NOT TIGHT AS SHOWN. PACKING DO NOT GLAND TIGHTEN LOCKIN PACKING NUT OR GLAND OPEN LOCKING BALL VAL NUT UNTIL OR OPEN SENSOR BALL ASSEMB VALVE UNTIL IS READY SENSOR TO ASSEMBLY GO ON-STR IS READY TO GO ON-STREAM.

10 10 Sensor Assembly In-Service Instructions-/B Ball Valve Option PLEASE NOTE REFER to pages 16 and 17 of the REFER TO PAGES 15 AND 16 OF THE sensor assembly and itemized SENSOR ASSEMBLY AND ITEMIZED PART part LIST FOR list ALL for THESE all COMPONENTS. these components THE FINAL ASSEMBLY IS NOW READY TO BE PLACED INTO SERVICE, WITH PACKING GLAND LOCKING NUT ENGAGED BUT NOT TIGHTENED AND SENSOR IN THE RETRACTED POSITION. [Step B]. INSERT STAGE #1 SUBASSEMBLY INTO PROCESS. THE IN-SERVICE ASSEMBLY SHOULD APPEAR AS SHOWN BELOW. [Step A]. A]. TO TO PLACE PLACE ASSEMBLY INTO INTO SERVICE OPEN OPEN BALL BALL VALVE COMPLETELY. Caution: OPENING VALVE SUBJECTS SENSOR ASSEMBLY TO TO LINE LINE PRESSURE. IF THE IF THE SENSOR IS IS NOT NOT RETRACTED COMPLETLY AGAINST AGAINST STOP, STOP, OPENING OPENING THE THE VALVE VALVE COULD COULD RESULT RESULT IN IN THE THE SENSOR SENSOR SUDDENLY SUDDENLY RETRACTING RETRACTING THE THE REMAINING REMAINING DISTANCE DISTANCE CAUSING DAMAGE TO THE CAUSING DAMAGE TO THE SENSOR ASSEMBLY OR INJURY SENSOR ASSEMBLY OR INJURY TO THE SERVICE PERSON. TO THE SERVICE PERSON. [Step C]. SECURE SENSOR IN PLACE BY TIGHTENING LOCKING NUT AND FERRULES OF GLAND FITTING, ITEM NO.3. DO NOT INSERT TIP OF SENSOR BEYOND INSIDE WALL OF PROCESS PIPE TO AVOID TORQUE AND POSSIBLE BREAKAGE.

11 11 Sensor Service Instructions Before Servicing remove the model ph97 sensor from service following the step-by-step instructions [a] and [b] in order as shown below: [Step B]. [Step FULLY B]. FULLY RETRACT RETRACT STAGE #1 STAGE SUBASSEMBLY #1 SUB- SHAFT. ASSEMBLY SHAFT. [Step A]. LOOSEN LOCKING NUT [Step AND A]. FERRULES LOOSEN OF LOCKING GLAND FITTING, NUT AND ITEM FERRULES NO. 3. OF GLAND Caution: FITTING, THE ITEM SENSOR NO. 3. ASSEMBLY IS Caution: STILL UNDER THE SENSOR PRESSURE. ASSEMBLY LOOSENING IS STILL UNDER THE LOCKING PRESSURE. NUT COULD LOOSENING RESULT THE IN THE LOCKING SENSOR NUT RETRACTING COULD RESULT SUDDENLY IN THE AND SENSOR WITH RETRACTING A GREAT DEAL SUDDENLY OF FORCE. AND THIS WITH COULD A GREAT CAUSE DEAL DAMAGE OF FORCE. TO THIS THE COULD SENSOR CAUSE ASSEMBLY DAMAGE OR TO INJURY THE SENSOR TO THE SERVICE ASSEMBLY PERSON. OR INJURY TO THE SERVICE PERSON.

12 12 Sensor Service Instructions (Continued) Before Servicing remove the model PH97 sensor from service following the step-by-step instructions [C] and [D] in order as shown below: [Step c]. Close ball valve completely. [Step D]. Completely unthread gland fitting, item no.4, from valve assembly 10

13 13 Sensor Service Instructions (Continued) Continue servicing of the model ph97 sensor by following the step-by-step instructions [e] through [g] in order as shown below: [Step G]. TO TEST SENSOR PERFORM A [Step 2-POINT G]. TO TEST CALIBRATION SENSOR WITH PERFORM ph BUFFER A 2-POINT AS CALIBRATION SHOWN WITH BELOW. ph BUFFER AS SHOWN BELOW. IF THE IF SENSOR THE SENSOR TESTS TESTS WITHIN WITHIN ACCEPTABLE ACCEPTABLE LIMITS LIMITS REINSTALL REINSTALL AND PLACE AND PLACE SENSOR SENSOR BACK IN SERVICE BACK BY IN SERVICE FOLLOWING BY FOLLOWING ASSEMBLY ASSEMBLY INSTRUCTIONS. INSTRUCTIONS. IF TESTING IF TESTING PROVES PROVES SENSOR SENSOR T0 BE T0 FAULTY BE FAULTY [Step F]. Before testing the CONTINUE CONTINUE WITH THE WITH SERVICE THE SERVICE INSTRUCTIONS INSTRUcTIONS sensor be sure that it is clean FOR SENSOR REPLACEMENT. FOR SENSOR REPLACEMENT. [Step E]. Remove stage #1 Assembly from valve assembly. With the stage #1 Subassembly completely removed from the valve assembly the sensor may now be tested or replaced.

14 14 Sensor Replacement Instructions Before Servicing remove the model PH87 sensor from service following the step-by-step instructions [a] and [D] in order as shown below: [Step C]. WHILE FIRMLY GRIPING [Step SHEATH C]. While PUSH firmly ON COUPLER griping TUBE sheath - JUNCTION BOX ASSEMBLY TO push on coupler tube junction box UNSEAT SENSOR O-RINGS assembly to unseat sensor o-rings [Step A]. REMOVE JUNCTION BOX COVER AND DISCON- NECT [Step ALL A]. WIRES REMOVE FROM TERMINALS. JUNCTION BOX COVER AND DISCONNECT ALL WIRES FROM TERMINALS. [Step B]. WHILE FIRMLY GRIPING THE [Step SENSOR B]. WHILE AND THE FIRMLY SHEATH GRIPING AT THE THE SAME SENSOR TIME UNTHREAD AND THE SHEATH THEM AT FROM THE THE SAME COUPLER TIME UNTHREAD ASSEMBLY THEM BUT DO FROM NOT COMPLETELY THE COUPLER DISENGAGE ASSEMBLY BUT THREADS. DO NOT COMPLETELY DISENGAGE THREADS. [Step D]. COMPLETELY UNTHREAD SENSOR [Step FROM D]. COUPLER COMPLETELY TUBEUNTHREAD ASSEMBLY. SENSOR FROM COUPLER TUBE ASSEMBLY. CONTINUE WITH SERVICE INSTRUCTIONS CONTINUE AT WITH STEP SERVICE "N". INSTRUCTIONS AT STEP N.

15 15 Sensor Replacement Instructions (Continued) DISASSEMBLE THE ASSEMBLY INTO THE COMPONENT PARTS AS SHOWN IN ONE OF THE ILLUSTRATIONS BELOW. TO INSTALL A NEW SENSOR AND RETURN THE MODEL PH87 TO SERVICE FOLLOW THE ASSEMBLY INSTRUCTIONS STARTING FROM STAGE #1 STEP D (PAGE 4) FIGURE 1: STANDARD ASSEMBLY READY FOR FIGURE SENSOR 1: REPLACEMENT STANDARD ASSEMBLY READY FOR SENSOR REPLACEMENT FIGURE 2: Assembly with sensor mounted FIGURE 2: junction ASSEMBLY box WITH ready for SENSOR MOUNTED JUNCTION sensor replacement BOX READY FOR SENSOR REPLACEMENT

16 16 Sensor Housing Assembly 8 JUNCTION Junction BOX box PLEASE NOTE REFER to pages 15 and 16 of the sensor assembly and itemized part list for all these components ALL O-RINGS REQUIRE PROPER LUBRICATION PRIOR TO SERVICING. WE RECOMMEND USING PARKER O LUBE OR EQUIVALENT. FOLLOW THE LUBRICATION INSTRUCTIONS PROVIDED BY THE MANUFACTURER. 2 Required 9 ph SENSOR ph sensor (SEE (see MODEL model PH97 ph97 SPEC SHEET) spec sheet)

17 17 Sensor Housing Assembly These are the individual part numbers for the items shown in the exploded view on the previous page. Part numbers for a complete assembly are listed on next two pages, on the specific drawing. Item Part Number Description 1 M1234DQ Coupler Assembly, Kynar (PVDF), N=7 M1234TV-A Coupler Assembly, Kynai (PVDF), N=21 These part numbers includes the o-ring 1a, 2 M1234DS O-rings, viton, sensor, size -019, quantity of 10 3 M1234DT Compression Fitting, 1 Tube x 1 MNPT 3a M1234DW Compression Fitting, Nut 3b M1234DX Compression Fitting, Ferrule, Kynar (PVDF) 3c M1234EJ Compression Fitting, Body, Titanium 3d M1234DZ Compression Fitting, O-ring, viton, size M1234EA Sheath, Titanium, N=7 M1234JQ-A Sheath, Titanium, N=21 5 M1234WZ-A Bushing, 1.25 MNPT x 1 FNPT 6 M1234WY-A Ball Valve, Full Port, 1.25 NPT 7 M1234XA-A Nipple, 1.25 NPT 8 M1234EE Junction Box Assembly, Sensor Mount 9 See ph Sensor Specifications

18 18 "C" = MINIMUM CLEARANCE REQUIRED FOR SENSOR REMOVAL "R" = FULLY RETRACTED 3/4" FNPT 15.65" FULLY INSERTED "N" = FULLY INSERTED 3.72" 5.22" 1 1/4" MNPT MODEL NO. N LENGTH Insertion Length R DIMENSION Retraction Distance C DIMENSION Minimum Clearance PH87-07/B PH87-21/B Dart Road, Newnan, GA Tel.: Fax.: PH87 With /B Ball Valve Insertion Assembly: Dimensions & Clearance Requirements

19 19 "C" = MINIMUM CLEARANCE REQUIRED FOR SENSOR REMOVAL "R" = FULLY RETRACTED 3/4" FNPT 9.65" FULLY INSERTED "N" = FULLY INSERTED 3.72" 1 " MNPT MODEL NO. N LENGTH Insertion Length R DIMENSION Retraction Distance C DIMENSION Minimum Clearance PH PH Dart Road, Newnan, GA Tel.: Fax.: PH87 Insertion Assembly: Dimensions & Clearance Requirements

20 YOKOGAWA HEADQUARTERS 9-32, Nakacho 2-chome, Musashinoshi Tokyo 180 Japan Tel. (81) Fax (81) YOKOGAWA EUROPE B.V. Euroweg HD Amersfoort The Netherlands Tel. +31 (0) Fax +31 (0) info@nl.yokogawa.com YOKOGAWA CORPORATION OF AMERICA 2 Dart Road Newnan GA United States Tel. (1) Fax (1) info@yca.com YOKOGAWA ELECTRIC ASIA Pte. Ltd. 5 Bedok South Road Singapore Singapore Tel. (65) Fax (65) webinfo@yas.com.sg Yokogawa has an extensive sales and distribution network. Please refer to the website ( to contact your nearest representative. IM M1234JL-A Subject to change without notice Copyright 2008 Printed in The USA