Data sheet Knife gate valve WB PN10 DN
|
|
|
- Darrell Fisher
- 6 years ago
- Views:
Transcription
1 Page: 1(7) Introduction The Stafsjö WB knife gate valve is a bi-directional seated valve with full bore. Its main applications are different liquids at water, waste water and biogas plants. The WB is designed of a one piece valve body in cast iron. The sealing profile of Nitrile or EPDM is in level with the bore of the body which counteract clogging of the valve. The gate in polished stainless steel guarantees low actuating operations and minimal wear. The unique Stafsjö box packing TwinPack in three layers gives a secure sealing and high operation reliability. The flange sealing is made of rubber and it is integrated in the body of the valve. Further flange gaskets are therefore unnecessary. Due to the flexible design, The WB can be equipped with different types of manual and automatic actuators and accessories, such as limit switches. The Stafsjö knife gate valve WB is designed, manufactured, inspected and tested according to the European directive Pressure Equipment Directive (PED 97/23/EC) category II module A1 and is therefore CE marked. The WB valve is also available in an ATEX design (ATEX 94/9/EC II cat 3 G/D zone 2,22). Please contact Stafsjö or your local representative for advice. 0640
2 Page: 2(7) Design data Maximum working pressure body at 20 C Maximum differential pressure at 20 C DN bar DN bar Basic equipment A. Valve body Material Max. temp. C Not recommended Cast Iron A GG Corrosive media Standard colour: electrostatic painted with powder epoxy colour, thickness µm, RAL B. Gate DN Body Material Stainless steel A AISI316L/W Stainless steel A SS2333/AISI304/W C. Sealing profile Max. temp. C EPDM E 120 NITRIL N 100 D. Box packing ph Max. temp. C TwinPack TM TY E. Flange drilling EN 1092 PN 10 F. Face-to-face dimensions DIN 3202 K1 DN50-300, Stafsjö DN Actuator Manual Automatic Hand wheel HW Pneumatic cylinder AC Hand lever DN HL Elektric motor EM Chain wheel CW Hydraulic cylinder MH Bevel gear BG Pneumatic cylinder recommended sizes at 5 bar air pressure AC Maximum force (kn) 3,5 3,5 3,5 3,5 3,5 3,5 9,0 9,0 9,0 14,1 14,1 14,1 22,1 The table gives recommended cylinder sizes at normal operation at 5 bar air pressure. For other operating conditions, please contact Stafsjö or your local representative for advice. Electric motor recommended size with AUMA multi-turn AUMA Attachment F10/A F10/A F10/A F10/A F10/A F10/A F10/A F10/A F10/A F10/A F10/A F10/A F10/A Electric motors are mounted according to standard ISO The table gives recommended motor sizes at normal operation. For other operating conditions, please contact Stafsjö or your local representative for advice For ATEX classified and other actuators, please contact Stafsjö or your local representative for advice.
3 Page: 3(7) Accessories Limit switches Mechanical Ersce E100 Inductive ifm electronic IG-2008-ABOA / IG wire V AC/DC ifm electronic IG-3008-BPKG / IG wire V DC PNP Accessories to pneumatic cylinder Solenoid valve Metal Work SOV 35 SOS OO ¼ Metal Work SOV 45 SOS OO ½ Magnetic limit switch Elobau wire V AC/DC Elobau PE 3-wire V DC For accessories classified according to ATEX or advice regarding accessories, please contact Stafsjö or your local representative. Valve capacity K v K v value for water at 20 C DN [mm] 3 m / h K v [ ] bar Fully open valve / Bore [mm 2 ] DN [mm] 3 m / h K v [ ] bar Fully open valve / Bore [mm 2 ] Pressure tests Pressure tests are performed with water at 20 C according to ISO 5208 meaning: 1,5 x maximum working pressure for open valve shell test 1,1 x maximum differential pressure for closed valve obturator tightness test Leakage rate Rate A according to ISO 5208 no visible leakage for the duration of the test TAPPI TIS 405-8, MSS SP-81
4 Page: 4(7) Parts and Material 1 2c 2 2b 2a 1b a 4b 4 7g 7e 7f 20b 20a c 8b 8a c 7c 7d 13b 13a Pos Part Material Pos Part Material 1 Hand Wheel Cast iron (GG25), epoxy colour 8 Gland Ductile iron (GGG-50), epoxy colour 1b Straight pin Stainless steel (A2/DIN 1481) 8a PinnBolt Stainless steel (A2) 2 Yoke Steel (Q235), epoxy colour 8b Washer Stainless steel (A2) 2a Bearing Bar brass (CuZn39Pb3) 8c Nut Stainless steel (A2) 2b Slide Washer POM 9 Boxpackning * See equipment D 2c Bearing Bar brass (CuZn39Pb3) 10 Valve body See equipment A 3 Stem Stainless Steel SS c Flange sealing * NBR 4 Stem Nut Bar brass (CuZn39Pb3) 13 Sealing profile * See equipment C 4a Washer Stainless steel (A2) 13a Pin, long * Stainless Steel 4b Bolt Stainless steel (A2) 13b Pin, short * Stainless Steel 6 Gate See equipment B 16 Gate guard, Not for HW Steel (Q235), epoxy colour 7 Beam Steel (Q235), epoxy colour 18 Cylinder See data sheet 7c Bolt Stainless steel (A2) 20 Bolt Stainless steel (A2) 7d Washer Stainless steel (A2) 20a Washer Stainless steel (A2) 7e Washer Stainless steel (A2) 20b Nut Stainless steel (A2) 7f Nut Stainless steel (A2) 25 Piston rod Stainless Steel (AISI303) 7g Bolt Stainless steel (A2) * Recommended spare parts
5 Page: 5(7) Main dimensions E G K STAFSJÖ STAFSJÖ STAFSJÖ F C A L H D B J Dimension (mm) A B C D E F G H J K L Actuator EM is rotated 45 for DN Weight, valve incl. hand wheel (HW) kg 5,5 6,5 7,5 9,
6 Page: 6(7) Flange Drilling All specifications subject to change without notice.
7 Stafsjö standard Data sheet material Materials Knife corresponding gate valve foreign material standards Page: 7(7) MATERIALS Name Sweden Europé Germany U Japan Type Stafsjö SS EN Material Name EN std W. Nr. DIN ASTM AISI UNS JIS Castings Cast iron GG EN-JL2030 EN-GJL-HB195 EN 1561 W A48 No 30B G5501 FC20 / FC200 Cast iron GG EN-JL2040 EN-GJL-HB215 EN 1561 W A48 No 35B G5501 FC25 / FC250 Ductile iron GGG EN-JS1050 EN-GJS EN 1563 W A G5502 FCD50/FCD500 Stainless steel (not pressure purposes) GX5CrNi19-10 EN A CF8 A743 G5121:80 SCS13 Stainless steel GX5CrNiMo EN W A351 CF8M A351 G5121:80 SCS14 Stainless steel CG8M A351 CG8M 317 Stainless steel CG3M L Stainless steel Hastelloy C Hastelloy C276 W A494 CW12MW N10276 Stainless steel - SMO 254 SMO A351 CK3MCuN S31254 Stainless steel - Duplex Duplex EN Sheet metal - pressure purposes Steel P265GH EN A516 Grade 60 Stainless steel SS2333 / X5CrNi18-10 EN W A240 Type S30400 SUS304 Stainless steel SS2343 / X3CrNiMo EN W A240 Type S31599 SUS316 Stainless steel SS2347 / X5CrNiMo EN W A240 Type S31600 SUS316 Stainless steel SS2348 / 316L X2CrNiMo EN W A240 Type316L 316L SUS316L Stainless steel 317L X2CrNiMo EN W A240 Type317L 317L SUS317L Stainless steel SS2377 / FAL X2CrNiMoN EN W S32205 S31803 SUS329J3L Stainless steel-ti.stab. 316Ti Ti Titanium Titan / TiGr2 B265 Grade SMO 254 SMO X1CrNiMoCuN EN S31254 Sheet metal - other Steel S355JR EN A572 Grade 50 G3106 SM490A Stainless steel SS X5CrNi18-10 EN W A S30400 G SUS304 Stainless steel SS X3CrNiMo EN W A S31600 G SUS SMO 254 SMO X1CrNiMoCuN EN S31254 Bar, pipe Steel SS S355J2H EN A618 Grade 3 Steel SS1312/Q S235JRH EN A36 Stainless steel SS X20Cr13 EN W S42010 SUS420J1 Stainless steel SS X6Cr17 EN W A S43000 G SUS430 Stainless steel SS X5CrNi18-10 EN W A S30400 G SUS304 Stainless steel SS X3CrNiMo EN W S31600 SUS316 Stainless steel SS X8CrNiS18-9 EN W S30300 G SUS303 Stainless steel SS X14CrMoS17 EN W F S43020 G SUS430F Screw, nut Stainless steel A X5CrNi18-10 W S30400 SUS304 Stainless steel A SUS316 Steel SS Aluminium Casting AlSi7MgFe 4244 EN AC AlSi7MgFe EN 1706 B26 356,0 A03560 H AC4C Casting ENAC-AlSi12(b) EN AC AlSi12Mn EN 1706 Casting ENAC-AlSi9Cu3(Fe) 4250 EN AC AlSi9Cu3(Fe) EN B413.0 H ADC10 Extruded EN AW-6063-T6 EN AW-6063-T6 EN AW-6063-T6 AlMg0.7Si EN 1706 AA6063 Copper alloy Brass SS Cast brass SS CuZn39Pb3 EN 1982 Bar brass SS CuZn39Pb3 EN A C36000 Oil bronze 2991 oilbronze 2991 ISO 2795
XV en /5 XV Knife gate valve DN
-80-800-en-04 1/5 The Stafsjö knife gate valve is a compact bi-directional valve with full bore. The valve is specially designed with regard to good flow characteristics and simple maintenance which makes
Stafsjö Valves AB. SE Stavsjö, Sweden. Tel: +46 (0) Fax: +46 (0) A Bröer Group company
Product: W W Stafsjö s knife gate valve W is a bi-directional valve with full bore. It is made to handle different liquids, especially in water, waste water and biogas plants. The W valve is designed of
Knife gate valve HG - Standard
Knife gate valve HG - Standard V R Data is only for informational purpose. All specifications are subject to change without notice. 1 Knife gate valve HG Stafsjö s knife gate valve HG has excellent flow
Knife gate valve SLF. Data is only for informational purpose. All specifications are subject to change without notice issue 3
Knife gate valve SLF Data is only for informational purpose. All specifications are subject to change without notice. V R 1 2013-02-15 issue 3 Knife gate valve SLF Stafsjö s knife gate valve SLF is a flanged
SLV EN 1092 PN 10 ANSI B16.5 Class 150 AS 2129 Table D AS 2129 Table E
SLV EN 2 PN ANSI.5 Class 0 AS 2 Table D AS 2 Table E Stafsjö s knife gate valve SLV is bi-directional and designed for the most demanding slurry and abrasive applications. It is a full bore valve with
Knife gate valve WB. Data is only for informational purpose. All specifications are subject to change without notice issue 13
Knife gate valve WB Data is only for informational purpose. All specifications are subject to change without notice. 1 2016-06-03 issue 13 Knife gate valve WB Stafsjö's knife gate valve WB is bi-directional
Knife gate valve WB. Data is only for informational purpose. All specifications are subject to change without notice issue 12
Knife gate valve WB Data is only for informational purpose. All specifications are subject to change without notice. 1 2015-05-28 issue 12 Knife gate valve WB Stafsjö's knife gate valve WB is bi-directional
Knife gate valves for water, sludge and abrasive slurry
Knife gate valves for water, sludge and abrasive slurry The production of knife gate valves started in 1928 in close co-operation with customers... In order to guarantee valve function upon delivery the
Knife gate valve WB14
Knife gate valve WB14 Data is only for informational purpose. All specifications are subject to change without notice. 1 2016-08-19 issue 10 Knife gate valve WB14 Stafsjö's knife gate valve WB14 is bi-directional
Knife gate valve WB14
Knife gate valve WB14 Data is only for informational purpose. All specifications are subject to change without notice. 1 Knife gate valve WB14 Stafsjö's knife gate valve WB14 is bi-directional and can
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve
Knife gate valve WB11
Knife gate valve WB11 Data is only for informational purpose. All specifications are subject to change without notice. 1 2016-12-28 issue 13 Knife gate valve WB11 Stafsjö's knife gate valve WB11 is bi-directional
Knife gate valve MP. Data is only for informational purpose. All specifications are subject to change without notice issue 3
Knife gate valve MP Data is only for informational purpose. All specifications are subject to change without notice. 1 2012-11-27 issue 3 Knife gate valve MP Stafsjö s knife gate valve MP is a full bore
Knife gate valve MP. Data is only for informational purpose. All specifications are subject to change without notice issue 5
Knife gate valve MP Data is only for informational purpose. All specifications are subject to change without notice. 1 2015-06-11 issue 5 Knife gate valve MP Stafsjö s knife gate valve MP is a full bore
Knife gate valve WB. Data is only for informational purpose. All specifications are subject to change without notice issue 11
Knife gate valve WB Data is only for informational purpose. All specifications are subject to change without notice. 1 2013-01-16 issue 11 Knife gate valve WB Stafsjö's knife gate valve WB is bi-directional
KNIFE GATE VALVE Product Ref. : KG02W/KG02L
General Description Model KG02 is a bidirectional knife gate valve suitable for most industrial application cases. With one piece body design, it combines robust and economy giving best cost effective
DOUBLE GATE KNIFE GATE VALVE. OBX 09/09 8th EDITION Reserves the right to change specifications without notice
DOUBLE GATE KNIFE GATE VALVE The model knife gate is a bi-directional valve widely used in the Pulp and Paper industry (recycling or secondary fibre processing) designed to handle high concentrated or
BI-DIRECTIONAL KNIFE GATE VALVE
BI-DIRECTIONAL KNIFE GATE VALVE The model knife gate is a bi-directional valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off on suspended
Knife gate valve MV. Data is only for informational purpose. All specifications are subject to change without notice issue 22
Knife gate valve MV Data is only for informational purpose. All specifications are subject to change without notice. 1 Knife gate valve MV Stafsjö s knife gate valve MV is used within many different fields
SQUARE PORT KNIFE GATE VALVE
SQUARE PORT KNIFE GATE VALVE The model knife gate is a square port low-pressure valve for highly solid loaded fluids or solids, mainly used in bulk handling and silo outlet applications in industries such
WAFER STYLE KNIFE GATE VALVE
MODEL WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut
WAFER STYLE KNIFE GATE VALVE
WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off on
BI-DIRECTIONAL KNIFE GATE VALVE
Wastewater treatment plants Food and Beverage Chemical plants Sizes: Working pressure: DN 2"/ 50mm to DN 10"/ 250mm DN 12"/300mm to DN 16"/ 400mm DN 18"/450mm DN 20"/500mm to DN 24"/ 600mm DN 28"/700mm
HEAVY DUTY KNIFE GATE VALVE
HEAVY DUTY KNIFE GATE VALVE The model knife gate is an uni-directional lug type valve designed according to MSS-SP-81 and TAPPI TIS 405-8 for industrial service applications. The design of the body and
Technical changes kept in reserve THROUGH CONDUIT KNIFE GATE VALVE
Technical changes kept in reserve THROUGH CONDUIT KNIFE GATE VALVE The B model knife gate is a bi-directional wafer valve designed for media with high consistency. The double seat design assures a non-clogging
Knife gate valve HG. Data is only for informational purpose. All specifications are subject to change without notice issue 13
Knife gate valve HG Data is only for informational purpose. All specifications are subject to change without notice. 1 Knife gate valve HG Stafsjö s knife gate valve HG has excellent flow characteristics
WAFER STYLE KNIFE GATE VALVE
11 WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off
Technical changes kept in reserve WAFER STYLE KNIFE GATE VALVE. DN 50 to DN 250: 10 kg/cm² DN 300 to DN 400: 6 kg/cm²
WAFER STYLE KNIFE GATE VALVE The A model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off
Knife gate valve WB14E
Knife gate valve WB14E Data is only for informational purpose. All specifications are subject to change without notice. 1 Knife gate valve WB14E Stafsjö s WB14E knife gate valve is a high performance shut-off
HOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). The special design of the
Knife gate valve XV. Data is only for informational purpose. All specifications are subject to change without notice issue: 3
Knife gate valve XV Data is only for informational purpose. All specifications are subject to change without notice. 1 Knife gate valve XV Stafsjö s knife gate valve XV gives a secure and tight shutoff,
HOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The C model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). makes it ideal for use
THROUGH CONDUIT KNIFE GATE VALVE. OBX 09/11 2nd EDITION Revision 1 Reserves the right to change specifications without notice
THROUGH CONDUIT KNIFE GATE VALVE The model knife gate is a bi-directional wafer valve designed for media with high consistency. The double seat design assures a non-clogging shut off on either normal or
WAFER STYLE KNIFE GATE VALVE
WAFER STYLE KNIFE GATE VALVE The EX(SER.10) model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging
ROUND BY SQUARE PORT KNIFE GATE VALVE
ROUND BY SQUARE PORT KNIFE GATE VALVE The model knife gate is a wafer valve designed for handling difficult applications. This valve is suitable for using in recycling applications, like junk or sand traps
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a bi-directional wafer valve equipped with two metallic coved rubber sleeves designed for use in the handling of abrasive slurries, mainly in industries
DOUBLE GATE KNIFE GATE VALVE
DOUBLE GATE KNIFE GATE VALVE The model knife gate valve is a bi-directional valve widely used in the Pulp and Paper industry (paper recycling) and especially designed to handle high concentrated or contaminated
Knife gate valve RKO. Data is only for informational purpose. All specifications are subject to change without notice issue 20
Knife gate valve RKO Data is only for informational purpose. All specifications are subject to change without notice. 1 Knife gate valve RKO Stafsjö s knife gate valve RKO is reliable and particularly
L15 HEAVY DUTY KNIFE GATE VALVE STANDARD PARTS LIST
L15 HEAVY DUTY KNIFE GATE VALVE The L15 model knife gate is a uni-directional lug type valve designed according to MSS-SP-81 and TAPPI TIS 405-8 for industrial service applications. The design of the body
Knife gate valve HX. Data is only for informational purpose. All specifications are subject to change without notice issue 5
Knife gate valve HX Data is only for informational purpose. All specifications are subject to change without notice. 1 2017-06-13 issue 5 Knife gate valve HX Stafsjö s knife gate valve HX is an extreme
Knife gate valve TV. Data is only for informational purpose. All specifications are subject to change without notice issue 9
Knife gate valve TV Data is only for informational purpose. All specifications are subject to change without notice. 1 2015-06-08 issue 9 Knife gate valve TV Stafsjö s knife gate valve TV can be used an
S GATE KNIFE GATE VALVE WITH PNEUMATIC ACTUATOR
MAIN FEATURES The pneumatic S GATE knife gate valve is intended for the automatic shut off of pipes of the heavy fluids like slurries and powders. The main fields of application are the water treatment,
HEAVY DUTY KNIFE GATE VALVE. ANSI B16.5 (class 150) and DIN PN 10
HEAVY DUTY KNIFE GATE VALVE The SERIES knife gate is a uni-directional lug type valve designed according to the MSS-SP-1 and TAPPI TIS 405- standard for industrial service applications. The design of the
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a bi-directional full flanged valve equipped with two metal reinforced rubber sleeves designed for use in the handling of abrasive slurries, mainly
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a bi-directional full flanged valve equipped with two metal reinforced rubber sleeves designed for use in the handling of abrasive slurries, mainly
Knife gate valve JTV. Data is only for informational purpose. All specifications are subject to change without notice issue 11
Knife gate valve JTV Data is only for informational purpose. All specifications are subject to change without notice. 1 2015-05-21 issue 11 Knife gate valve JTV Stafsjö s knife gate valve JTV is reliable
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a bi-directional wafer valve equipped with two metallic coved rubber sleeves designed for use in the handling of abrasive slurries, mainly in industries
BIDIRECTIONAL WAFER Knife Gate Valve
09/03/2016 BIDIRECTIONAL WAFER Knife Gate Valve Bidirectional wafer design knife gate valve. Monoblock one piece cast iron body. Stainless steel gate. Two rubber sleeves. Provides high flow rates with
Materials : Cast iron or Stainless steel
Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 800 Between flanges PN10-10 C for NBR seat ( -15 C for EPDM ) + 90 C for NBR seat ( + 110 C for EPDM ) Max Pressure : 10 Bars
BI-DIRECTIONAL KNIFE GATE VALVES XD-PRE SERIES WITH D/A PNEUMATIC ACTUATOR
BI-DIRECTIONAL KNIFE GATE VALVES XD-PRE SERIES KGV XD-PRE SERIES FULLY LUGGED WITH RISING STEM & HANDWHEEL KGV XD-PRE SERIES FULLY LUGGED WITH D/A PNEUMATIC ACTUATOR KGV XD-PRE SERIES FULLY LUGGED WITH
UNIDIRECTIONAL Knife Gate Valve
12/04/2016 UNIDIRECTIONAL Knife Gate Valve Unidirectional knife gate valve. Mechanically welded body. Various seat and packing materials available. Face to face dimension in accordance with standard, it
MADE OF STAINLESS... Certificate 3.1
MADE OF STAINLESS... Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 300 Between flanges PN10-10 C + 90 C Max Pressure : 10 Bars up to DN 200 Specifications : Rising rotating
Stafsjö s ATEX solutions for category 1 D (Zone 20)
Stafsjö s ATEX solutions for category 1 D (Zone 20) Data is only for informational purpose. All specifications are subject to change without notice. 1 2017-02-2 issue 1 ATEX solutions for category 1 D
BI-DIRECTIONAL KNIFE GATE VALVE KGV-XD SEMI LUGGED WITH D/A PNEUMATIC ACTUATOR
BI-DIRECTIONAL KNIFE GATE VALVE KGV-XD SEMI LUGGED WITH RISING STEM & HANDWHEEL KGV-XD SEMI LUGGED WITH D/A PNEUMATIC ACTUATOR KGV-XD FULLY LUGGED WITH BONNET & HADNWHEEL The XD model knife gate is a Bi-directional
BIDIRECTIONAL WAFER Knife Gate Valve
31/07/2014 BIDIRECTIONAL WAFER Knife Gate Valve - Bidirectional wafer-design knife gate valve. - One-piece cast body. - Provides high flow rates with low pressure drop. - Various seat and packing materials
UNI-DIRECTIONAL KNIFE GATE VALVE
UNI-DIRECTIONAL KNIFE GATE VALVE The MU-CYL model knife gate is a Uni-directional valve, equipped with automatic or manual driver, that by its loose elastomeric clamping ring design (tight version) ensures
WAFER Disc Check Valve
18/04/2013 WAFER Disc Check Valve WAFER swing or tilting disc check valve (can be manufactured with flanges on request). One piece cast body which provides easy evacuation of solid particles contained
Size : Ends : Min Temperature : Max Temperature : Materials : Cast iron body. Certificate 3.1
Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 500 Between flanges PN10-10 C for NBR seat ( -15 C for EPDM ) + 90 C for NBR seat ( + 110 C for EPDM ) Max Pressure : 10 Bars
KNIFE GATE VALVES -- MODEL A
PRODUCT DESCRIPTION Wafer style, uni-directional knife gate valve. One piece integral cast body with guides to support the gate and seating wedges. High flow rates with low pressure drops. Several seat
WAFER Disc Check Valve
12/03/2012 WAFER Disc Check Valve WAFER swing or tilting disc check valve (can be manufactured with flanges on request). One piece cast body which provides easy evacuation of solid particles contained
FKB INDÚSTRIA DE EQUIPAMENTOS LTDA. KNIFE GATE VALVE VGU-01 (Rev. 02/2016)
General Description The model FKB VGU-01 is developed in accordance with MSS-SP 81 Standard and its function is blocking the fluid sewage. They are light equipments for semi-lug body and flange installation,
BI-ECCENTRIC Disc Retention Valve
05/11/2015 - Oscillating disc retention valve with dual eccentricity and straight seat. - Option of manufacturing WAFER type or with flange boring in accordance with customer requirements. - Distance between
MADE OF STAINLESS... Certificate 3.1
MADE OF STAINLESS... Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 800 Between flanges PN10-10 C for NBR seat ( -15 C for ) + 90 C for NBR seat ( + 110 C for ) Max Pressure
BUTTERFLY VALVE 17 SERIES Gearbox
DN H1 H2 H3 BUTTERFLY VALVE 17 SERIES Gearbox FIGURE: 17234ER: 17234BR: 17234VR: Seat in EPDM, with gearbox Seat in Buna, with gearbox Seat in Viton, with gearbox B ØR L DIMENSIONS: (mm) DN L B XR H1 H2
Mono Flanged Type Long Face to Face
Year : Mono Flanged Type Long Face to Face Page 1 Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve enter b.v. Year : General Product Information Technical
UNIWORLD series PNEUMATIC VALVES
UNIWORLD series PNEUMATIC VALVES 5100AD/E 07 2013 SINGLE SEAT TWO WAY ON-OFF VALVES PED 97/23/CE / ATEX 94/9/CE / MACHINERY DIRECTIVE 2006/42/CE TYPE 5100 AD Normally open air closes Face-to-face ASME
PRZEPUSTNICE. B-599 Centric butterfly valve PN16 from -10ºC to +130ºС DN32 DN200 PN-EN 2-3
BUTTERFLY VALVES PRZEPUSTNICE TYPE DESCRIPTION NOMINAL PRESSURE TEMPERATURE DIAMETER STANDARD PAGE B-599 Centric butterfly valve PN16 from -10ºC to +130ºС DN32 DN200 PN-EN 2-3 B-099 Centric butterfly valve
VALVES 5
info@ayvaz.com www.ayvaz.com GLOBE VALVES GV-16, GV-25, GV-40 GV-16 GV-25 GV-40 GG-25 Cast Iron GSC-25 Cast Steel GSC-25 Cast Steel Seat Stainless Steel AISI 304 Stainless Steel AISI 304 Stainless Steel
The Keystone Series GR is a heavy duty industrial resilient seated butterfly valve aimed at general purpose applications.
The Keystone Series GR is a heavy duty industrial resilient seated butterfly valve aimed at general purpose applications. Features Wafer and lugged body design with face-to-face dimension, according to
2 PIECES BALL VALVE PN63
2 PIECES BALL VALVE PN63 Model/Ref: 176 www.lauridsenindustri.com Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 300 Between flanges ISO PN10-10 C + 90 C Max Pressure : 10 Bars up to DN
S-GATE type KNIFE VALVE with PNEUMATIC ACTUATOR. DN 450 to 600. See below. 5 bar min. / 7 bar max. Prohibited use on gases of group 1 for DN>100
CHARACTERISTICS The S-GATE knife valve is equipped with a pneumatic actuator and is dedicated to the automatic shut-off of loaded fluids such as slurries and powdery materials. The standard application
Fabricated Bevel Gear Operator Bi-Directional Metal Seat 150 PSI Bi-Directional Resilient Seat 150 PSI
Knife Gate Valves Uni-Directional (Metal Seated) Manual Handwheel Style KGV...2 Carbon Steel Technical Data 150 PSI 2 24...3 304 Stainless Steel Technical Data 150 PSI 2 24...3 316 Stainless Steel Technical
Soft seat. Torque values tables 13 Head losses tables 14 Flange and bolts tables 15 Flanges 16 Tests 16
soft seat PD, KI Series 1 technical data 1 components DN 0-300 2 components DN 30-00 3 KI Series 4 components DN 600-800 4 KA, KX tecnical data technical data KA series 6 components DN 40-300 6 components
Long Face to Face. Bonded Liner Butterfly Valve Mono Flanged Type (Long) Series 130. Document : S130 Revision : 3 Year : 2014
Year : Long Face to Face Page 1 Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve enter b.v. Year : General Product Information Technical Data Description
KNIFE GATE VALVES -- MODEL D
PRODUCT DESCRIPTION Flanged unidirectional knife gate valve for high pressure applications One piece integral cast body with seating wedges and bolted bonnet. High flow rates with low pressure drops. Several
Size : Ends : Min Temperature : Max Temperature : Reinforced lug from DN200 to DN1400 MADE OF STAINLESS...
MADE OF STAINLESS... Reinforced lug from DN200 to DN1400 Size : Ends : Min Temperature : Max Temperature : DN 32 to 1400 mm Between flanges PN10/16-10 C ( with EPDM seat ) + 110 C ( with EPDM seat ) Max
BIDIRECTIONAL WAFER Knife Gate Valve
05/10/2012 BIDIRECTIONAL WAFER Knife Gate Valve Bidirectional wafer design knife gate valve. Monoblock one piece cast iron body. Stainless steel gate. Two rubber sleeves. Provides high flow rates with
BALL VALVE - 340BA SERIES Pneumatic actuator - El-O-Matic
C D E BALL VALVE - 30BA SERIES Pneumatic actuator - El-O-Matic FIGURE: PD: Pneumatic actuator, double acting PE: Pneumatic actuator, spring return G F DIMENSIONS: (mm) Ø DN C PD PE PD D E F Kg PE D E G
KEYSTONE OPTISEAL WAFER AND LUGGED
A resilient seated butterfly valve for general purpose applications FEATURES GENERAL APPLICATION Food and beverage processing, dry bulk conveying, paper mills, slurry handling etc. Grease or silicone free
BUTTERFLY VALVE 27 SERIES Pneumatic actuator - El-O-Matic
C D E FIGURE: PD: pneumatic actuator, double acting PE: pneumatic actuator, spring return PEO: pneumatic actuator, spring return, normally open BUTTERFLY VALVE 27 SERIES Pneumatic actuator - El-O-Matic
RAIMONDI. High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services.
Fig. 6022-6025 RAIMONDI High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services. Features Forged body materials of highest quality, all in compliance with ASME
Materials : Cast iron or Stainless steel
Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 700 Between flanges GN10-10 C for cast iron type ( -15 C for S.S. ) + 80 C for cast iron type ( + 110 C for S.S. ) Max Pressure : 10 Bars up
BS 1452 Gr Gr. 420/ Gr. 420/ AB2 304 C C S S S S16. E mm
WAFER TYPE BUTTERFY VAVE SPECIFICATION FOR BS EN 1092-2 PN10 / PN16 FANGE MOUNTING FACE-TO-FACE DIMENSION TO ISO 5752 / BS 5155 / BS EN 593 EVER / WORM GEAR OPERATOR PRESSURE / TEMPERATURE RATINGS BFV-WB
AVK (WWE) BUTTERFLY VALVE DN 50 to DN (EVTLS)
Flangeless tapped lug Wafer Type Design code EN593 Flange connection to EN 1092 PN 6, 10, 16, 25 DESIGN Body Flangeless tapped lug wafer type End Connection EN 1092 PN 6, 10 and 16 ASME B16.5 cl. 150 /
Butterfly valves. Technical features 11 Coupling 12 Elements list 12 Tables 13 torque values 13 dimensions 15
TT series valve TT Series 1 technical data 1 components DN 50-300 Stainless steel disc Stainless steel + PTFE disc 3 components DN 350-500 Tables 5 dimensions 5 torque values Installation instructions
UNIDIRECTIONAL Guillotine Valve
Unidirectional "LUG" guillotine valve. Monobloc cast body with interior slides for optimum movement of the gate during operation. Provides high flow rates with low pressure drop. Various seat and packing
NAF-Torex butterfly valves DN , Size 3-28, PN 10-40, ANSI Class 150, 300
NAF-Torex butterfly valves DN 80-700, Size 3-28, PN 10-40, ANSI Class 150, 300 Fk 41.42(18)GB 11.04 Primary characteristics NAF-Torex, High-Performance butterfly valve is available with either metal-to-metal
CHECK VALVES. MOUNTING: - flow direction marked with arrow on body; - mounting position in conformity with the technical sheet recommendation.
CHECK VALVES RR page 1 R MAIN APPLICATIONS: Transport and distribution of : - cold and hot industrial water; - saturated vapours; - petroleum products; on condition that the compatibility regarding the
KEYSTONE BUTTERFLY VALVE PARASEAL RANGE
The ParaSeal range features a proven disc, shaft and seat arrangement designed for use in high pressure and high velocity applications FEATURES GENERAL APPLICATION Water, food and beverage processing,
KEYSTONE BUTTERFLY VALVE PARASEAL RANGE
The ParaSeal range features a proven disc, shaft and seat arrangement designed for use in high pressure and high velocity applications FEATURES GENERAL APPLICATION Water, food and beverage processing,
MADE OF STAINLESS...
MADE OF STAINLESS... Size : Ends : Min Temperature : Max Temperature : DN 32 to 1400 mm Between flanges PN10/16 and ISO PN20 ANSI150-10 C (with EPDM seat ) + 110 C ( with EPDM seat ) Max Pressure : 16
NAF-Setball ball sector valves for MC-pulp DN , PN 16-40, ANSI Class
NAF-Setball ball sector valves for MC-pulp DN 80-300, PN 16-40, ANSI Class 150-300 Fk 41.54(2)GB 11.02 Primary characteristics NAF-Setball for MC-pulp is a ball sector valve with metalto-metal seating
UNIDIRECTIONAL Knife Gate Valve
UNIDIRECTIONAL Knife Gate Valve 24/04/2013 Unidirectional knife gate valve. One piece cast body with guides to support gate and seat wedges. Provides high flow rates with low pressure drop. Various seat
BUTTERFLY VALVE - WAFER FAF 3500
PRODUCTION STANDARDS DN40 DN600 PN 6-10-16 CLASS 150 Design EN 593 Connection Wafer Type ISO 7005-1 EN 1092-1 Face to Face EN 558 Series 20 Marking EN 19 Tests EN 12266-1 Corrosion Protection Electrostatic
ALC-3 BUTTERFLY VALVES NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS DESIGN. ANSI Class PN DN
BUTTERFLY VALVES ALC-3 NOMINAL PRESSURE ANSI Class 150-600 PN 10-100 NOMINAL 2-80 DN 50-2000 MATERIALS Cast Iron Carbon Steel Low Alloy Steel CONNECTIONS Wafer Lugged Flanged Butt Weld DESIGN Eccentric
Ref WAFER BUTTERFLY VALVE. Model/Ref:
Ref. 1150-1158 WAFER BUTTERFLY VALVE Model/Ref: 1150-1158 www.lauridsenindustri.com Ref. 1150-1158 Size : Ends : Min Temperature : Max Temperature : DN 32 to 1400 mm Between flanges PN10/16 and ISO PN20
Valve Solutions for the Bulk Material Industry
Valve Solutions for the Bulk Material Industry SUCCESS STORY Plant name & location: Tronox, llc. Hamilton, Ms Application: Ore Silo Inlet Media: Titanium Rutile Ore Tronox, llc., formerly Kerr McGee Chemical
Ref LUG BUTTERFLY VALVE. Model/Ref:
LUG BUTTERFLY VALVE Model/Ref: 1160 1168 Reinforced lug from DN200 to DN1400 : www.lauridsenindustri.com Reinforced lug from DN200 to DN1400 : Size : Ends : Min Temperature : Max Temperature : DN 32 to
BIDIRECTIONAL Knife Gate Valve
BIDIRECTIONAL Knife Gate Valve 30/10/2013 Bidirectional knife gate valve. Two piece cast body, joined by screws, with internal guides for smooth movement of gate during operation. Provides high flow rates
BUTTERFLY VALVE VF-7 Series
BUTTERFLY VALVE VF-7 Series CENTRIC, RUBBER SEATED LEVER GEAR PNEUMATIC - ELECTRIC OPERATED ALLOWABLE PRESSURE DN 40 300mm : 16 bar DN 350 1200mm : 10 bar INVESTMENT CASTING STAINLESS STEEL BODY 2 12 (50mm