INSTALLATION GUIDE. Directed Digital Solutions TL11. Designed by Installers for Installers

Transcription

1 INSTALLATION GUIDE Directed Digital Solutions TL11 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components

2 Contents Warning! Safety first... 3 Introduction... 4 Pre-installation and application warnings... 4 Vehicle application guide... 5 Wiring connections... 6 Main power harness (H1), 12-pin thick gauge connector... 6 Auxiliary output harness (H2), 16-pin black connector... 6 Analog harness (H3), 18-pin white connector... 7 MC501 harness (H4), 8 thick-gauge wires (optional)... 7 Installation (wiring diagrams & vehicle wiring reference charts)... 8 Type Type Type Connecting the module Important! Manual or automatic transmission selection Optional sensors RF Systems When used in conjunction with SmartStart Module programming LED diagnostics and troubleshooting Soft reset Hard reset Learning the Tach (not needed with Virtual Tach) Initializing Virtual Tach (not needed with hardwired or data tach applications) Limited lifetime consumer warranty Quick Reference Guide... 37

3 Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3 Directed Digital Solutions TL11

4 Introduction The TL11 firmware for Directed Digital Solutions is compatible with specific Lexus, Pontiac, Scion and Toyota vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using TL11. If you would prefer using this system as a digital solution, go to and search for the make, model and year of the vehicle. This will allow you to find the proper firmware and corresponding installation guide. Warning! This module can only be programmed via the web tool, which can be found on or using the Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module using the XKLoader. Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness compatible Keys required for programming 1 Keys required for operation 0 Important: If your vehicle is NOT equipped with transponders or CANs, please flash your module with an Analog firmware. This guide will help you with the installation diagram and vehicle wiring reference chart. Some Toyota models have different encryption types. Please look at your key blade and indentify the markings. A dot "." means the vehicle is compatible with TL11 firmware. "G" or "H" indicates the vehicle is not compatible with this firmware. Refer to "Key Types" on page 5 for more information. Keyless will remain functional during remote start. Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. Refer to the "Vehicle wiring reference chart" following each installation type. General notes: This section highlights important information for this specific firmware. [1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. [2] The siren is ONLY required when enabling the security features during module flashing. [3] The Green wire is ONLY required for starter disable and antigrind applications. [4] Connection required ONLY if vehicle is equipped with Autolights. [5] Door trigger input is required when enabling the security features during module flashing. [6] Second starter connection may be required in some vehicles. [7] Keysense connection may be required in some vehicles. Additional parts required (maximum required): 87 Diode 6A 0 x 1A Diodes 87a x Relay esistor x Resistor Fuse 7.5A 0 x Fuse 4 Directed Digital Solutions TL11

5 Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control Lexus ES GX LS LX RX RX RX 400h Pontiac Vibe 1 1 Vibe 3 Scion tc xb xd Toyota Runner Avalon Camry Camry Corolla 1 1 Corolla FJ Cruiser Highlander Highlander Highlander Hybrid 3 3 Land Cruiser Matrix 1 1 Matrix RAV RAV4 3 3 Sequoia Sienna Solara Tacoma Tundra Venza 3 Yaris Yaris Sedan Legend: PK: Transponder & Immobilizer Override DL: OE Door Lock & Alarm Controls RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status Key Types DL-Door Unlock DL-Driver Priority Unlock Some Toyota models have different encryption types. Please look at your key blade and identify the markings. A dot. means the vehicle is compatible with TL11 firmware. G or H indicates the vehicle is not compatible with this firmware. Standard Key G-stamped keys H-stamped keys DL-Hatch Glass Release For vehicles with G-stamped key, see the TL5 firmware. DL-Trunk / Hatch Release RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-E-Brake Status For vehicles with H-stamped key, see the TL10 firmware. TL11 works only with standard key. ST-Ignition Status H 5 Directed Digital Solutions TL11

6 Wiring connections The wiring connections listed below are specific to this firmware. Main power harness (H1), 12-pin thick gauge connector Conn./Pin Color Description H1/1 White Relay 3 COM Parking Light Output 1 H1/2 White/Brown Relay 3 N.O. Parking Light Input 1 H1/3 Brown/Red Relay 2 N.O. No Connection H1/4 Yellow/Red Relay 2 COM Autolight Interrupt (vehicle side) H1/5 Orange/Red Relay 2 N.C. Autolight Interrupt (connector side) H1/6 Yellow Relay 1 COM (+) Starter 2 Output 1 H1/7 White Relay 3 COM Clutch Bypass Output 1 H1/8 White/Brown Relay 3 N.O. Clutch Bypass Input 1 H1/9 Black (-) Ground H1/10 Red (+) 12V Input H1/11 Orange/Yellow Relay 1 N.C. No Connection 1 H1/12 Brown Relay 1 N.O. (+) 12V Input 1 Auxiliary output harness (H2), 16-pin black connector Conn./Pin Color Description H2/1 Violet/Brown No Connection H2/2 Yellow/Black Data TX H2/3 Orange/Black Data RX H2/4 Tan HS CAN Low H2/5 Tan/Black HS CAN High H2/6 Light Green No Connection H2/7 Orange/Green No Connection H2/8 Orange/Brown No Connection H2/9 Violet/Green No Connection H2/10 Green/Black (-) Parking Lights Output 2 H2/11 White/Violet No Connection 2 H2/12 White/Red No Connection 2 H2/13 Lt. Blue/Black No Connection 2 H2/14 Green/Red No Connection 2 H2/15 N/A No Connection H2/16 Violet/Yellow No Connection 1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 6 Directed Digital Solutions TL11

7 Analog harness (H3), 18-pin white connector Conn./Pin Color Description H3/1 Lt. Blue/Red No Connection H3/2 Black/White (-) Parking Brake Input (manual transmission) 2 H3/3 Gray (-) Hood Input 2 H3/4 N/A No Connection H3/5 Gray/Black (+) Glow Plug Input 2 H3/6 Violet/White (AC) Tach Input 2 H3/7 Dark Blue (-) Unlock Output 1 H3/8 Brown/Black No Connection 1 H3/9 Red/White (-) Trunk Release Output 1 H3/10 White/Green (-) Door Trigger Input 2 H3/11 Yellow/Green (+) Door Input 2 H3/12 Blue/Red No Connection H3/13 Light Blue (-) Trunk Trigger Input 2 H3/14 Pink/Yellow (-) Activation (start) Input H3/15 Dark Green (-) Lock Output 1 H3/16 Brown/White (+) Brake Input 2 H3/17 Brown (+) Siren Output 1 H3/18 Blue/White (-) Ground When Running (status) Output 1 ; (-) Keysense Output 1 MC501 harness (H4), 8 thick-gauge wires (optional) Conn./Pin Color Description H4/1 Pink/White (+) Ignition 2/Flex Relay Output 3 H4/2 Red/White (+) Fused (30A) Ignition 2/Flex Relay Input H4/3 Pink (+) Ignition Output (also input to Yellow in ribbon cable) H4/4 Red (+) 12 Volt (battery) Input H4/5 Orange (+) Accessory Output H4/6 Red (+) 12 Volt (battery) Input H4/7 Green Starter Input (from key switch) 4 H4/8 Violet (+) Starter Output (to starter) 1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. 3. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 4. The Green wire is only required for starter disable and anti-grind applications. 7 Directed Digital Solutions TL11

8 Installation (wiring diagrams & vehicle wiring reference charts) Type 1 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Headlight Switch (white conn. at headlights) 1 9 HS CAN High: Pin OBDII Plug Black Connector Transponder Key Amplifier (black conn. around ignition) HS CAN Low: Pin Autolight: Pin 19 (-) Parking Lights: Pin 18 Refer to Vehicle Connections for wire and connector details. CUT Data TX: Yellow/Black: 2 Data RX: Orange/Black: 3 HS CAN Low: Tan: 4 (+) Starter Output (Car Side): Violet: 8 Starter Input (Key Side): Green: 7 (+) 12V Input: Red: 6 (+) Ignition Input/Output: Pink: 3 (+) 12V Input: Red/White: 2 8 thick-gauge wires MC501 4 White 7 White HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 10 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) Ignition 2 Output: Pink/White: 1 12: Brown: (+) 12V Input Hood Pin (-) Hood Input: Gray: 3 10: Red: (+) 12V Input 9: Black: (-) Ground Ignition Switch Dash Fuse Box (white 1-pin conn.) (+) Siren Output: Brown: 17 6: Yellow: (+) Starter 2 Output 5: Orange/Red: Autolight Interrupt (conn.side) Siren 4: Yellow/Red: Autolight Interrupt (veh.side) Refer to the Vehicle Wiring Reference Chart for wire and connector details. 8 Directed Digital Solutions TL11

9 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Pontiac Vibe RX Lt. Blue 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Tan 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Starter 1 Black 8 (+) Ignition switch. White 8 B Starter 2 (2.4L only) White 1 (+) Ignition switch. White 8 B Ignition 1 Brown 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B HS CAN High Lt. Green 6 Data OBDII. White 16 C HS CAN Low White 14 Data OBDII. White 16 C Parking Lights Brown 18 (-) Headlight switch. White 20 D 12V White 1 (+) Dash fuse box. White 1 E Scion xb RX Pink 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V White 7 (+) Ignition switch. White 8 B Starter 1 White 8 (+) Ignition switch. White 8 B Starter 2 White 1 (+) Ignition switch. White 8 B Ignition 1 Gray 6 (+) Ignition switch. White 8 B Ignition 2 White 4 (+) Ignition switch. White 8 B HS CAN High Lt. Green 6 Data OBDII. Black 16 C HS CAN Low White 14 Data OBDII. Black 16 C Parking Lights White 18 (-) Headlight switch. White 20 D 9 Directed Digital Solutions TL11

10 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Camry RX Brown 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Red 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V Black 5 (+) Ignition switch. White 8 B Starter 1 Blue 7 (+) Ignition switch. White 8 B Starter 2 Gray 3 (+) Ignition switch. White 8 B Ignition 1 Yellow 6 (+) Ignition switch. White 8 B Ignition 2 Pink 1 (+) Ignition switch. White 8 B HS CAN High Black 6 Data OBDII. Black 16 C HS CAN Low White 14 Data OBDII. Black 16 C Autolights Green 19 Cut Headlight switch. White 20 D Parking Lights Black 18 (-) Headlight switch. White 20 D Toyota Corolla RX Lt. Blue or Pink 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Tan or Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Starter 1 Black or White 1 (+) Ignition switch. White 8 B Starter 2 White 8 (+) Ignition switch. White 8 B Ignition 1 Brown or Gray 6 (+) Ignition switch. White 8 B Ignition 2 Green or White 4 (+) Ignition switch. White 8 B HS CAN High Lt. Green 6 Data OBDII. Black 16 C HS CAN Low White 14 Data OBDII. Black 16 C Parking Lights Brown or White 18 (-) Headlight switch. White 20 D 12V White 1 (+) Dash fuse box. White 1 E Toyota Highlander RX Red 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Lt. Blue 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V White/Black 5 (+) Ignition switch. White 8 B Starter 1 Yellow 7 (+) Ignition switch. White 8 B Starter 2 Red 3 (+) Ignition switch. White 8 B Ignition 1 Black 6 (+) Ignition switch. White 8 B Ignition 2 Lt. Blue 1 (+) Ignition switch. White 8 B HS CAN High Blue 6 Data OBDII. Black 16 C HS CAN Low White 14 Data OBDII. Black 16 C Autolights Green 19 Cut Headlight switch. White 20 D Parking Lights Lt. Blue 18 (-) Headlight switch. White 20 D Toyota Matrix RX Lt. Blue 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Tan 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Starter 1 Black 8 (+) Ignition switch. White 8 B Starter 2 (2.4L only) White 1 (+) Ignition switch. White 8 B Ignition 1 Brown 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B HS CAN High Lt. Green 6 Data OBDII. Black 16 C HS CAN Low White 14 Data OBDII. Black 16 C Parking Lights Brown 18 (-) Headlight switch. White 20 D 12V White 1 (+) Dash fuse box. White 1 E 10 Directed Digital Solutions TL11

11 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota RAV RX Pink 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V Blue 7 (+) Ignition switch. White 8 B Starter 1 Yellow 8 (+) Ignition switch. White 8 B Starter 2 White 1 (+) Ignition switch. White 8 B Ignition 1 White 6 (+) Ignition switch. White 8 B Ignition 2 Pink 4 (+) Ignition switch. White 8 B HS CAN High Black 6 Data OBDII. Black 16 C HS CAN Low White 14 Data OBDII. Black 16 C Autolights Green 19 Cut Headlight switch. White 20 D Parking Lights White 18 (-) Headlight switch. White 20 D 11 Directed Digital Solutions TL11

12 Type 2 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Headlight Switch (Scion) (white conn. at headlights) HS CAN High: Violet, pin OBDII Plug Black Connector HS CAN Low: White, pin 14 Transponder Key Amplifier (black conn. around ignition) Data RX: Green, pin 4 (-) Parking Lights: White, pin 13 Data TX: Violet, pin 5 Data TX: Yellow/Black: 2 Data RX: Orange/Black: 3 HS CAN Low: Tan: 4 (+) Starter Output (Car Side): Violet: 8 Starter Input (Key Side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory Output: Orange: 5 (+) 12V Input: Red: 4 8 thick-gauge wires MC501 4 White 7 White HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 10 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) Ignition Input/Output: Pink: 3 Hood Pin (-) Hood Input: Gray: 3 10: Red: (+) 12V Input (+) Siren Output: Brown: 17 9: Black: (-) Ground Ignition Switch Siren Refer to the Vehicle Wiring Reference Chart for wire and connector details. 12 Directed Digital Solutions TL11

13 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Scion xd (Key) RX Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Violet 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Starter Black 7 (+) Ignition switch. White 8 B 12V Gray 5 (+) Ignition switch. White 8 B Accessory White 2 (+) Ignition switch. White 8 B Ignition Pink 6 (+) Ignition switch. White 8 B CAN High Violet 6 Data OBDII diagnostic connector. Black 16 C CAN Low White 14 Data OBDII diagnostic connector. Black 16 C Parking Lights White 13 (-) Headlight switch. White 13 D 13 Directed Digital Solutions TL11

14 Type 3 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Transponder Key Amplifier (black conn. around ignition) Diagnostic Connector at OBDII Refer to Vehicle Wiring Reference Charts for wire and connector details. (AC) Tach: Pin 9 Data TX: Yellow/Black: 2 Data RX: Orange/Black: 3 (+) Starter Output (Car Side): Violet: 8 Starter Input (Key Side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory Output: Orange: 5 (+) 12V Input: Red: 4 (+) Ignition Input/Output: Pink: 3 (+) 12V Input: Red/White: 2 (+) Ignition 2 Output: Pink/White: 1 8 thick-gauge wires MC501 4 White 7 White OR (-) Parking Lights Output: Green/Black: 10 Hood Pin (-) Hood Input: Gray: 3 (AC) Tach Input: Violet/White: 6 (-) Unlock Output: Dk.Blue: 7 (-) Trunk Release Output: Red/White: 9 10: Red: (+) 12V Input Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 12: Brown: (+) 12V Input Ignition Switch Siren (-) Door Trigger Input: White/Green: 10 (-) Lock Output: Dk.Green: 15 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: 17 (-) Keysense Output: Blue/White: 18 9: Black: (-) Ground 6: Yellow: (+) Starter 2 Output 5: Orange/Red: Autolights Interrupt (conn.side) 4: Yellow/Red: Autolights Interrupt (veh.side) Refer to the Vehicle Wiring Reference Charts for wire and connector details. Refer to Vehicle Wiring Reference Chart for wire and connector details. Parking lights & Autolights are secondary options for Tach. 14 Directed Digital Solutions TL11

15 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Lexus ES RX Green/White 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Blue/Yellow 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Blue 2 (-) Key warning switch. White 2 B 12V White Red 7 (+) Ignition switch. White 8 B Starter 1 Black/White 8 (+) Ignition switch. White 8 B Starter 2 Green/Yellow 1 (+) Ignition switch. White 8 B Ignition 1 Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 Black/Yellow 4 (+) Ignition switch. White 8 B Accessory Blue/Red 3 (+) Ignition switch. White 8 B Autolights White 12 Cut Headlight switch. White 17 D Parking Lights Red 14 (-) Headlight switch. White 17 D Lock Blue/Yelllow 4 (-) DDM (Drivers Door Module) in drivers door. White 20 E Unlock Blue 14 (-) DDM in drivers door. White 20 E Brake Green/White 15 (+) Bottom of fuse box. White 20 G Trunk Release Red or Blue/Yellow 5 (-) Body ECU on left rear of fuse box. White 18 G Door Trigger Green/Red 16 (-) Body ECU on left rear of fuse box. White 20 G Tach Black/Orange 5 AC ECM behind glove box. White 31 J 15 Directed Digital Solutions TL11

16 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Lexus GX RX Yellow 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Yellow/Black 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V White/Red or White/ Blue 7 (+) Ignition switch. White 8 B Starter Green/Black 8 (+) Ignition switch. White 8 B Ignition 1 Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 Blue/Yellow 4 (+) Ignition switch. White 8 B Accessory White/Green 3 (+) Ignition switch. White 8 B Tach Black/White 9 AC OBDII. White 16 C Lock Blue 4 (-) Power window master switch. White 20 E Unlock Green 14 (-) Power window master switch. White 20 E Door Trigger White 8 (-) Body ECU on dash fuse box. White 20 G Autolights Green/Orange 3 Cut Body ECU under drivers side dash. White 26 G Parking Lights Green 8 (-) Body ECU under drivers side dash. White 26 G Keysense Green/Yellow 14 (-) Body ECU under drivers side dash. White 26 G Brake Green/Yellow 16 (+) Dash fuse box. White 16 G Lexus LS RX Red/White 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Blue/Black 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Door Trigger Violet/White 6 (-) Ignition key cylinder light. Black 7 B 12V White/Blue 7 (+) Ignition switch. White 8 B Starter Black/White 4 (+) Ignition switch. White 8 B Ignition 1 Green/Yellow 6 (+) Ignition switch. White 8 B Ignition 2 Red/White 2 (+) Ignition switch. White 8 B Accessory White/Green 3 (+) Ignition switch. White 8 B Keysense Lt. Green/Black 2 (-) Ignition switch. White 8 B Lock Red/Black or Violet/Red 10 (-) DDM (Drivers Door Module) in drivers door. White 24 E Unlock Black/Green or Violet/ Green 9 (-) DDM in drivers door. White 24 E Hazard Orange 2 (-) Rear of drivers fuse box. White 10 G Trunk Release Violet 2 (-) Body ECU on dash fuse box. White 22 G Brake Green/Orange 1 (+) Brake pedal switch. Green 4 H Lexus LX RX Blue/Black 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Violet/Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Red/Black 2 (-) Key warning switch. White 2 B Starter Black/White 8 (+) Ignition switch. White 8 B Ignition 1 Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 Blue/Black 4 (+) Ignition switch. White 8 B Accessory Black 3 (+) Ignition switch. White 8 B Tach Black 9 AC OBDII. Black 16 C Door Trigger Green/White 16 (-) Drivers fuse box, top left. White 25 G Lock Blue/White 4 (-) DDM (Drivers Door Module) in drivers door. White 20 E Unlock Green/Black 14 (-) DDM in drivers door. White 20 E Parking Lights Green/Black 14 (-) Headlight switch. White 17 D Brake Green/White 1 (+) Brake pedal switch. Blue 4 H 16 Directed Digital Solutions TL11

17 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Lexus RX RX Lt.Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Brown 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V Red 7 (+) Ignition switch. White 8 B Starter 1 Blue 8 (+) Ignition switch. White 8 B Starter 2 White 1 (+) Ignition switch. White 8 B Ignition 1 Violet 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B Accessory Gray 3 (+) Ignition switch. White 8 B Keysense Black 2 (-) Ignition switch. White 8 B Tach Black 9 AC OBDII. Black 16 C Autolights Brown 19 Cut Headlight switch. White 20 D Parking Lights Orange 18 (-) Headlight switch. White 20 D Lock Brown N/A (-) Drivers kick panel. N/A N/A F Unlock Violet N/A (-) Drivers kick panel. N/A N/A F Door Trigger Lt. Blue 5 (-) Right side of dash fuse box. White 11 G Brake Gray 2 (+) Brake pedal switch. Black 4 H Power Liftgate Violet 2 (-) Power liftgate switch. White 2 I Lexus RX RX Lt. Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Brown 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Black 2 (-) Key warning switch. White 4 B 12V Red 7 (+) Ignition switch. White 8 B Starter 1 Blue 8 (+) Ignition switch. White 8 B Starter 2 White 1 (+) Ignition switch. White 8 B Ignition 1 Violet 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B Accessory Red 3 (+) Ignition switch. White 8 B Autolights Brown 19 Cut Headlight switch. White 20 D Parking Lights Orange 18 (-) Headlight switch. White 20 D Lock Brown 4 (-) Power window master switch. White 20 E Unlock Gray 14 (-) Power window master switch. White 20 E Brake Blue or Brown 3 (+) Fuse box middle connector. White 12 G Door Trigger Lt. Green or Lt. Blue 5 (-) Right side of dash fuse box. White 12 G Power Liftgate Violet 2 (-) Power liftgate switch. White 2 I Tach White 9 AC ECM behind glove box. Black 16 J 17 Directed Digital Solutions TL11

18 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Lexus RX 400h RX Lt. Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Brown 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Black 2 (-) Key warning switch. White 4 B 12V Red 7 (+) Ignition switch. White 8 B Starter Blue 8 (+) Ignition switch. White 8 B Ignition 1 Violet 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B Accessory Brown or Gray 3 (+) Ignition switch. White 8 B Tach Black 9 AC OBDII. Black 16 C Autolights Brown 19 Cut Headlight switch. White 20 D Parking Lights Orange 18 (-) Headlight switch. White 20 D Lock Brown 4 (-) Power window master switch. White 20 E Unlock Gray 14 (-) Power window master switch. White 20 E Brake Blue 3 (+) Bottom of fuse box. White 12 G Door Trigger Lt. Blue 5 (-) Right side of dash fuse box. White 12 G Power Liftgate Violet 3 (-) Power liftgate switch. Black 4 I Pontiac Vibe 2008 RX Blue 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Blue/Black 2 (-) Key warning switch. Black 2 B 12V White 1 (+) Ignition switch. White 6 B Starter Red 4 (+) Ignition switch. White 6 B Ignition 1 Black/White 6 (+) Ignition switch. White 6 B Ignition 2 Black/Yellow 2 (+) Ignition switch. White 6 B Accessory Blue/Red 3 (+) Ignition switch. White 6 B Lock Green 6 (-) Drivers kick panel. White 10 F Unlock Blue/Yellow 7 (-) Drivers kick panel. White 10 F Tach Black 5 AC Body ECU behind glove box. White 31 G Brake Green/White 1 (+) Brake pedal switch. White 4 H Trunk Release Blue/White 2 (-) Trunk release switch. White 5 I Door Trigger Red/Yellow N/A (-) Drivers "A" pillar. N/A N/A K Scion tc RX Yellow 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Red 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V Red 7 (+) Ignition switch. White 8 B Starter 1 Black 8 (+) Ignition switch. White 8 B Starter 2 Green 1 (+) Ignition switch. White 8 B Ignition 1 Blue 6 (+) Ignition switch. White 8 B Ignition 2 Yellow 4 (+) Ignition switch. White 8 B Accessory Gray 3 3 Ignition switch. White 8 B Tach Black 9 AC OBDII. White 16 C Parking Lights Brown 14 (-) Headlight switch. White 17 D Lock Green or Blue 15 (-) Drivers kick panel. White 20 F Unlock Violet or Pink 14 (-) Drivers kick panel. White 20 F Brake Blue 9 (+) Drivers kick panel. White 30 F Trunk Release Orange 12 (-) Drivers kick panel. Gray 12 F Door Trigger Blue 2 (-) Dash fuse box. White 6 G Keysense Black 26 (-) Dash fuse box. White 32 G 18 Directed Digital Solutions TL11

19 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota 4Runner RX Pink/Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Lt. Green/Red 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Green/Yellow 2 (-) Key warning switch. Blue 4 B 12V White/Blue 2 (+) Ignition switch. White 8 B Starter Green/Black 8 (+) Ignition switch. White 8 B Ignition 1 Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 Blue/Yellow 4 (+) Ignition switch. White 8 B Accessory White/Green 3 (+) Ignition switch. White 8 B Trunk Release Orange 12 (-) Drivers kick panel. Gray 12 F Lock Blue 6 (-) Drivers kick panel. White 18 F Unlock Green 8 (-) Drivers kick panel. White 18 F Brake Green/Yellow 16 (+) Front of Body ECU on dash fuse box. White 16 G Door Trigger White 8 (-) Dash fuse box. White 20 G Parking Lights Green 8 (-) Body ECU, middle connector. White 26 G Autolights Green/Orange 3 Cut Body ECU, top connecter. White 26 G Tach Black/White 19 AC Junction connector above gas pedal. Blue 22 L Toyota Avalon RX Lt. Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Brown 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Black 2 (-) Key warning switch. White 4 B Starter 1 Blue 8 (+) Ignition switch. White 8 B Starter 2 Red 1 (+) Ignition switch. White 8 B 12V Black 7 (+) Ignition switch. White 8 B Ignition 1 Yellow 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B Accessory Gray 3 (+) Ignition switch. White 8 B Parking Lights Blue 18 (-) Headlight switch. White 20 D Autolights Orange 19 Cut Headlight switch. White 20 D Lock Black 9 (-) Drivers kick panel. White 20 F Unlock Gray 19 (-) Drivers kick panel. White 20 F Door Trigger Brown 5 (-) Dash fuse box. White 12 G Tach Black 17 AC Left of steering column. White 18 G Brake White to Blue 3 (+) Brake pedal switch. White 12 H Trunk Release Blue 5 (-) Trunk release switch. White 6 I 19 Directed Digital Solutions TL11

20 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Camry RX Green/White 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Blue/Yellow 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Blue 2 (-) Key warning switch. Blue 2 B Door Trigger Green/Red 1 or 6 (-) Ignition key cylinder light. Gray or Black 12V White/Red 7 (+) Ignition switch. White 8 B Starter 1 Black/White 8 (+) Ignition switch. White 8 B Starter 2 Black/Yellow 1 (+) Ignition switch. White 8 B Ignition 1 Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 Black/Yellow 4 (+) Ignition switch. White 8 B Accessory Blue/Red 3 (+) Ignition switch. White 8 B Autolights White 12 Cut Headlight switch. White 17 D Parking Lights Red 14 (-) Headlight switch. White 17 D Trunk Release White/Blue 5 5-wire Drivers kick panel. White 12 F Lock Blue/Yellow 7 (-) Drivers kick panel. White 20 F Unlock Blue 2 (-) Drivers kick panel. White 20 F Brake Green/White 15 (+) Dash fuse box. White 20 G Tach "Black/Orange (V6) or White (V4)" 16 or 11 AC Right of steering column or behind cluster White Toyota Corolla RX Lt. Blue or Pink 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Tan or Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Blue/Black 2 (-) Key warning switch. White 2 B 12V White 1 (+) Ignition switch. White 6 B Starter Red 4 (+) Ignition switch. White 6 B Ignition 1 Black/White 6 (+) Ignition switch. White 6 B Ignition 2 Black/Yellow 2 (+) Ignition switch. White 6 B Accessory Blue/Red 3 (+) Ignition switch. White 6 B Parking Lights Green/White or Green 13 (-) Headlight switch. White 13 D Lock Green 6 (-) Drivers kick panel. White 10 F Unlock Blue/Yellow 7 (-) Drivers kick panel. White 10 F Brake Green/White N/A (+) Drivers kick panel, harness to rear. N/A N/A F Door Trigger Red/Yellow 6 (-) Rear of drivers fuse box. Gray 6 G Tach Black 5 AC ECM behind glove box. Black 31 G 2 or 6 22 or 40 B L or M 20 Directed Digital Solutions TL11

21 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota FJ Cruiser RX Pink/Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Lt. Green/Red 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V Blue/Black 7 (+) Ignition switch. White 8 B Starter 1 Green/Black 8 (+) Ignition switch. White 8 B Starter 2 Black/White 1 (+) Ignition switch. White 8 B Ignition 1 Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 Blue/Yellow 4 (+) Ignition switch. White 8 B Accessory White/Green 3 (+) Ignition switch. White 8 B Tach Black/White 9 AC OBDII. White 16 C Lock Blue 6 (-) Drivers kick panel. White 18 F Unlock Pink 8 (-) Drivers kick panel. White 18 F Brake Green/Yellow 16 (+) Bottom of dash fuse box. White 16 G Door Trigger White 8 (-) Dash fuse box. White 20 G Trunk Release Blue/Yellow 13 5-wire Back door ECU in tailgate. White 25 G Keysense Green/Yellow 14 (-) Right side of dash fuse box. White 26 G Parking Lights Green 8 (-) Right side of dash fuse box. White 26 G Toyota Highlander RX Gray 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX White 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Door Trigger Green 1 or 6 (-) Ignition key cylinder light. Gray or Black Keysense Green 2 (-) Key warning switch. White 4 B 12V Yellow 7 (+) Ignition switch. White 8 B Starter 1 Black/White 8 (+) Ignition switch. White 8 B Starter 2 Black 1 (+) Ignition switch. White 8 B Ignition 1 Gray 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B Accessory Blue 3 (+) Ignition switch. White 8 B Tach Black 9 AC OBDII. Black 16 C Autolights Pink 12 Cut Headlight switch. White 17 D Brake Green 6 (+) Drivers kick panel. White 14 F Lock See Tech Doc 1070 on Unlock See Tech Doc 1070 on 2 or 6 B 21 Directed Digital Solutions TL11

22 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Highlander Hybrid RX Gray 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Lt. Blue 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Door Trigger Black 1 or 6 (-) Ignition key cylinder light. Gray or Black Keysense Green 2 (-) Key warning switch. White 4 B Parking Lights Lt. Blue 4 (-) Dash fuse box. White 7 G 12V Yellow 7 (+) Ignition switch. White 8 B Starter Black 8 (+) Ignition switch. White 8 B Ignition 1 Gray 6 (+) Ignition switch. White 8 B Ignition 2 Green 4 (+) Ignition switch. White 8 B Accessory Blue 3 (+) Ignition switch. White 8 B Brake Green 6 (+) Drivers kick panel. White 14 F Tach Black 9 AC OBDII. Black 16 C Autolights Pink 12 Cut Headlight switch. White 17 D Lock See Tech Doc 1070 on Unlock See Tech Doc 1070 on Toyota Land Cruiser RX Blue/Black 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Violet/Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Red/Black 2 (-) Key warning switch. White 2 B Door Trigger Green/White 6 (-) Ignition key cylinder light. Black 7 B 12V White/Red 7 (+) Ignition switch. White 8 B Starter Black/White 8 (+) Ignition switch. White 8 B Ignition 1 Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 Blue/Black 4 (+) Ignition switch. White 8 B Accessory Black 3 (+) Ignition switch. White 8 B Tach Black 9 AC OBDII. Black 16 C Autolights Green/Orange 12 Cut Headlight switch. White 17 D Parking Lights Green/Black 14 (-) Headlight switch. White 17 D Lock Blue/White 4 (-) Drivers door ECU, in drivers door. White 20 E Unlock Green/Black 14 (-) Drivers door ECU, in drivers door. White 20 E Brake Green/White 1 (+) Brake pedal switch. Blue 4 H Toyota Matrix RX Blue 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Green 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Blue/Black 2 (-) Key warning switch. Black 2 B 12V White 1 (+) Ignition switch. White 6 B Starter Red 4 (+) Ignition switch. White 6 B Ignition 1 Black/White 6 (+) Ignition switch. White 6 B Ignition 2 Black/Yellow 2 (+) Ignition switch. White 6 B Accessory Blue/Red 3 (+) Ignition switch. White 6 B Parking Lights Green or Green/White 13 (-) Headlight switch. White 13 D Lock Green 6 (-) Drivers kick panel. White 10 F Unlock Blue/Yellow 7 (-) Drivers kick panel. White 10 F Trunk Release Blue/White 2 (-) Trunk release switch. White 5 I Tach Black 5 AC ECM behind glove box. White 31 J Door Trigger Red/Yellow N/A (-) Drivers "A" pillar. N/A N/A K 2 or 6 B 22 Directed Digital Solutions TL11

23 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota RAV RX Blue/Red 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Pink 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Door Trigger Red/White 1 or 6 (-) Ignition key cylinder light. White or Black Keysense Blue/Red 2 (-) Key warning switch. White 4 B 12V White 1 (+) Ignition switch. White 6 B Starter 1 Red 4 (+) Ignition switch. White 6 B Ignition 1 Black 6 (+) Ignition switch. White 6 B Ignition 2 Black/yellow 2 (+) Ignition switch. White 6 B Accessory 1 Blue/Red 3 (+) Ignition switch. White 6 B Tach Black 9 AC OBDII. Black 16 C Parking Lights Green or Green/Red 10 (+) Headlight switch. White 13 D Lock Blue/Orange 6 (-) Drivers kick panel. White 14 F Unlock Blue/Yellow 13 (-) Drivers kick panel. White 14 F Trunk Release Blue 21 5-wire Drivers fuse box. White 28 G Brake Green/White 12 (+) Drivers fuse box. White 32 G Toyota Sequoia RX Lt. Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Blue 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Starter Green 7 (+) Ignition switch. White 8 B Ignition 1 Black 6 (+) Ignition switch. White 8 B Ignition 2 Lt. Green 1 (+) Ignition switch. White 8 B Accessory Gray 2 (+) Ignition switch. White 8 B Tach White 9 AC OBDII. White 16 C Door Trigger Blue 10 (-) Interior light switch on dash. Black 10 D Lock Lt. Blue 14 (-) Drivers kick panel. Blue 17 F Unlock Pink 16 (-) Drivers kick panel. Blue 17 F Keysense Lt. Green 5 (-) Body ECU on back of fuse box. White 10 G 12V Blue 4 (+) Dash fuse box. White 24 G Autolights Pink or Green 21 Cut Body ECU on dash fuse box. White 26 G Parking Lights Orange 23 (-) Body ECU on dash fuse box. White 26 G Power Liftgate Red 26 (-) Body ECU on dash fuse box. White 26 G Brake Tan 1 (+) Brake pedal switch. Blue 4 H 2 or 6 B 23 Directed Digital Solutions TL11

24 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Sienna RX Yellow 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Yellow/Red 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Blue/Black 2 (-) Key warning switch. White 4 B 12V White/Red 5 (+) Ignition switch. White 6 B Starter Black/Yellow 4 (+) Ignition switch. White 6 B Ignition 1 Black 6 (+) Ignition switch. White 6 B Ignition 2 Black/Yellow 2 (+) Ignition switch. White 6 B Accessory Pink 3 (+) Ignition switch. White 6 B Autolights Violet 12 Cut Headlight switch. White 17 D Parking Lights Green/Black 14 (-) Headlight switch. White 17 D Lock Lt. Green 5 (-) Drivers kick panel. White 18 F Unlock Blue 7 (-) Drivers kick panel. White 18 F Door Trigger Red/Green (front dome light) and Red/White (rear dome light) 10 & 3 (-) Junction connector, left of dash fuse box. Isolate the front and rear dome lights with diodes. White 14 G Power Liftgate Yellow/Red 10 (-) Left of dash fuse box. White 22 G Brake Green/Yellow or Green/ White 21 (+) Dash fuse box. White 30 G Tach Black/Orange 37 AC Behind insturment cluster White 40 M Toyota Solara RX Yellow or Green/White 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Yellow/Red or Blue/ yellow 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Blue 2 (-) Key warning switch. White 4 B 12V White/Red 7 (+) Ignition switch. White 8 B Starter 1 Black/White 7 (+) Ignition switch. White 8 B Starter 2 Black/Yellow 1 (+) Ignition switch. White 8 B Ignition 1 (coupe) Red/Black 6 (+) Ignition switch. White 8 B Ignition 1 (convertible) Black/Red 6 (+) Ignition switch. White 8 B Ignition 2 (coupe) Black/Yellow 4 (+) Ignition switch. White 8 B Ignition 2 (convertible) Blue 4 (+) Ignition switch. White 8 B Accessory Blue/Red 3 (+) Ignition switch. White 8 B Tach Black/Ornage 9 AC OBDII. Black 16 C Autolights White 12 Cut Headlight switch. White 17 D Parking Lights Red 14 (-) Headlight switch. White 17 D Trunk Release White/Blue 11 5-wire Drivers kick panel White 18 F Lock Lt.Green (coupe) or Blue/ Yellow (convertible) 18 (-) Drivers kick panel. White 20 F Unlock Blue 2 (-) Drivers kick panel. White 20 F Door Trigger Green/Red 5 (-) Dash fuse box. White 12 G Brake Green/White 13 (-) Dash fuse box. White 14 G 24 Directed Digital Solutions TL11

25 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Tacoma RX Pink/Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Lt. Green/Red 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Green/Black 1 (-) Key warning switch. White 2 B 12V White/Red 5 (+) Ignition switch. White 8 B Starter 1 Green/Black 7 (+) Ignition switch. White 8 B Starter 2 Black/White 3 (+) Ignition switch. White 8 B Ignition 1 Black/red 6 (+) Ignition switch. White 8 B Ignition 2 Bue/Yellow 1 (+) Ignition switch. White 8 B Accessory White/Green 2 (+) Ignition switch. White 8 B Tach Black/White 9 AC OBDII. White 16 C Parking Light Green 18 (-) Headlight switch. White 20 D Lock Violet 4 (-) Drivers kick panel. White 10 F Unlock Green/Black 8 (-) Drivers kick panel. White 10 F Brake Blue 13 (+) Dash fuse box. White 13 G Door Trigger Blue 9 (-) Dash fuse box. Black 13 G Toyota Tundra RX Lt. Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Blue 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Starter Green 7 (+) Ignition switch. White 8 B Ignition 1 Black 6 (+) Ignition switch. White 8 B Ignition 2 Lt. Green 1 (+) Ignition switch. White 8 B Accessory Gray 2 (+) Ignition switch. White 8 B Keysense Gray 1 (-) Key warning switch. White 2 B Tach White 9 AC OBDII. White 16 C Door Trigger Blue 10 (-) Interior light switch on dash. Black 10 D Lock Lt. Blue 14 (-) Drivers kick panel. Blue 18 F Unlock Pink 16 (-) Drivers kick panel. Blue 18 F Autolights Green 21 Cut Body ECU on dash fuse box. White 26 G 12V Black 1 (+) Dash fuse box. White 1 G Parking Light Oranger or Tan 23 (-) Body ECU on dash fuse box. White 26 G Brake Tan 1 (+) Brake pedal switch. Blue 4 H 25 Directed Digital Solutions TL11

26 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Venza 2009 RX Lt. Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Brown 5 Data Transponder Key Amplifier on ignition switch. Black 7 A Keysense Brown 1 (-) Key warning switch. White 2 B 12V Blue 7 (+) Ignition switch. White 8 B Starter 1 Red 8 (+) Ignition switch. White 8 B Starter 2 Green 1 (+) Ignition switch. White 8 B Ignition 1 Green 6 (+) Ignition switch. White 8 B Ignition 2 Red 4 (+) Ignition switch. White 8 B Accessory Green 3 (+) Ignition switch. White 8 B Tach Gray 6 AC OBDII. Black 16 C Autolights Brown 19 Cut Headlight switch. White 20 D Parking Light Red 18 (-) Headlight switch. White 20 D Lock Brown 11 (-) Drivers kick panel. White 18 F Unlock Gray 8 (-) Drivers kick panel. White 18 F Door Trigger Pink 5 (-) Dash fuse box. White 12 G Brake Lt. Green or Blue 3 (+) Dash fuse box. White 25 G Power Liftgate Brown 4 (-) Power liftgate switch. Black 5 I Toyota Yaris RX Green 4 Data Transponder Key Amplifier on ignition switch. Black 7 A TX Violet 5 Data Transponder Key Amplifier on ignition switch. Black 7 A 12V Yellow 4 (+) Ignition switch. White 8 B Starter Black 7 (+) Ignition switch. White 8 B Ignition 1 Pink 6 (+) Ignition switch. White 8 B Ignition 2 Green 1 (+) Ignition switch. White 8 B Accessory White 2 (+) Ignition switch. White 8 B Tach Lt. Green or Tan 9 AC OBDII. White 16 C Parking Lights White 13 (-) Headlight switch. White 13 D Lock Brown 7 (-) Drivers kick panel. White 20 F Unlock Green 8 (-) Drivers kick panel. White 20 F Keysense Yellow 7 (-) Dash fuse box. White 14 G Door Trigger Pink 2 (-) Dash fuse box. White 6 G Brake Green or Violet 12 (+) Dash fuse box. White 30 G 26 Directed Digital Solutions TL11

27 Connecting the module Important! Before connecting the Directed Digital Solutions, it is important to ensure that the proper feature and function programming is selected using the configuration wizard. Visit to use the latest version of the online tool. Flashing a module using your computer: 1. Disconnect the main module from any (+) 12V power source, then connect it to your computer using the XKLoader2. 2. Go to using Internet Explorer; the configuration wizard will be displayed automatically. 3. Follow the instructions in the pop up window that will be displayed when the module is detected. Flashing a module using your smartphone or tablet: 1. Disconnect the main module from any (+) 12V power source, then connect it to the XKLoader3. 2. Launch the Directechs Mobile app on your smartphone or tablet. 3. Select FLASH YOUR MODULE and follow the on-screen instructions. When the flashing operation is successful, you can proceed with the instructions below. Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected. Uncut (default): Manual transmission. Cut: Automatic transmission. For safety reasons, all Directed Digital Solutions are shipped ready to use with a manual transmission (the yellow loop is untouched). If the loop is cut after power has been applied, it is necessary to cycle power to the main module (via the white 12- pin main power harness) so the unit will see the state change on the loop and appropriately configure the transmission type. Ready mode To successfully remote start a vehicle equipped with a manual transmission, the Ready Mode feature must be enabled before exiting the vehicle. Please refer to the Owner s Guide for more details on this required process. Additional connections required for vehicles equipped with a manual transmission (if not supported by firmware) Connection (-) E-Brake Status Input (Black/White, pin 2) (-) Door Trigger Input (White/Green, pin 10) OR (+) Door Input (Yellow/ Green, pin 11) (AC) Tachometer Input (Violet/White, pin 6) Description Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple (-) trigger emergency brake circuits note some vehicles do not and may require unique integration methodologies. Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor the door pins to allow the Ready Mode process to be enabled. Note: Some vehicles may require unique integration methodologies for this circuit. For more information, refer to Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) and learned successfully to the Directed Digital Solutions. 27 Directed Digital Solutions TL11