SL63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2

Size: px
Start display at page:

Download "SL63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2"

Transcription

1 SL63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2

2 WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 63 USES AN ELECTRONIC THROTTLE CONTROL (ETC), WHICH IS CONTROLLED BY THE ENGINE CONTROL UNIT (ECU) AND THE CALIBRATION INSIDE. A REFLASH DOES NOT PROPERLY RECALIBRATE THE ENGINE MANAGEMENT SYSTEM; THIS CREATES A DANGEROUS SITUATION THAT COULD RESULT IN A STUCK THROTTLE AND CAN LEAD TO INJURY OR DEATH. WEISTEC FULLY REPROGRAMS THE ECU TO MERCEDES STANDARDS, AND ENSURES THAT ALL ENGINE SAFETY CONTROLS ARE FULLY FUNCTIONAL. 1

3 WARNING! THE WEISTEC M156 SUPERCHARGER AND ACCOMPANYING PROGRAMMING ARE DESIGNED AROUND THE USE OF 91 OCTANE FUEL OR HIGHER ONLY. BEFORE YOU RUN YOUR MERCEDES WITH THE WEISTEC M156 SUPERCHARGER INSTALLED EVEN ONCE, YOU MUST EITHER DRAIN THE FUEL TANK COMPLETELY AND FILL IT UP WITH 91 OCTANE, OR BEGIN USING 91 OCTANE IN YOUR MERCEDES TWO COMPLETE FILLUPS BEFORE INSTALLATION. 2

4 WARNING! IF YOU ARE NOT EXPERIENCED IN THE AREA OF AUTOMOTIVE MECHANICS, WE STRONGLY URGE THAT YOU REFER THIS INSTALLATION TO A CERTIFIED INSTALLER OR TECHNICIAN. 3

5 WARNING! THE WEISTEC M156 SUPERCHARGER MUST BE FILLED WITH 160 ml OF PROVIDED OIL PRIOR TO ROTATION OF THE COMPRESSOR SCREW SYSTEM OR YOUR WARRANTY WILL BE VOIDED. 4

6 WEISTEC M156 SUPERCHARGER Installation Guide for MERCEDES AMG 63 Thank you for your purchase of the Weistec M156 Supercharger for the Mercedes AMG 63 with the 6.3L motor. We appreciate your business, and we know you will enjoy your product. For your benefit, please read the following instructions completely and thoroughly before attempting to install the supercharger. Many questions we have received from customers about the installation of our products that could have been easily solved by information listed in the accompanying installation guide. We want you to enjoy the product in its fully functional state, and reading this tutorial is the first step to getting you on your way to a more rare and powerful Mercedes AMG. PLEASE NOTE THAT IF YOU HAVE ANY AFTERMARKET POWERTRAIN PARTS ALREADY INSTALLED ON YOUR VEHICLE, YOU MUST RETURN THE CAR TO STOCK STATUS THIS INCLUDES PULLEYS, PROGRAMMING, ETC. THE CAR WILL NOT FUNCTION AND PARTS MAY NOT FIT PROPERLY IF OTHER AFTERMARKET PARTS ARE INSTALLED. We strongly urge that you also have at least one person to help you install the supercharger, as the unit is heavy. You will soon be on your way to installing the World's First Supercharger for the 6.3L! Again, thank you for choosing Weistec Engineering! 5

7 Table of Contents Tools Required... Error! Bookmark not defined. I. Disassembly... 2 II. Bumper and Underbody Removal III. Cradle Install and Air Tube Delete IV. Weistec M156 Supercharger Installation V. Power Steering Reservoir Relocation... Error! Bookmark not defined. VI. Intercooler System Installation and Plumbing VII. Bumper and Underbody Installation VIII. Supplementary Installation and Fluid Check

8 Tools Required Hydraulic Jack or service lift Jack Stands or transmission stand 1/4 Drive Ratchet 12" Long 1/4" Drive Extension 6.5mm 1/4 Drive Deep Well Socket 8mm 1/4 Drive Deep Well Socket 10mm 1/4 Drive Deep Well Socket 17mm 3.8" Drive Deep Well Socket 10mm Open End Wrench 13mm Open End Wrench 14mm Open End Wrench 15mm Open End Wrench 17mm Open End Wrench 1" Open End Wrench 8mm Ratcheting Wrench 3/8 Drive Ratchet 13mm 3/8" Drive Socket 16mm 3/8 Drive Deep Well Socket Vice 17mm 3/8" Drive Deep Well Socket 19mm Heavy Duty Deep Well Socket T-25 1/4" Drive Torx Bit T 30 1/4" or 3/8 Drive Torx Bit T-45 3/8" Drive Torx Bit T-50 3/8" Drive Torx Bit E-8 3/8" Drive Reverse Torx Bit E-10 3/8 Drive Reverse Torx Bit E-14 3/8" Drive Reverse Torx Bit Flat Head Screw Driver Wire Cutter Pushpin Removal Tool 6mm Drive Hex Bit 8mm Drive Hex Bit Mechanics Rags Vacuum Painters Tape Fluid evacuator 7

9 Impact Gun (Optional) Crimp Style clamp tool 5mm Drill bit Drill Grinder (Optional) Torque Wrench 1

10 I. Disassembly Before removing battery terminal, double check vehicle is in Park, and driver side window is completely down. 1. Disconnect the Negative battery terminal by: a. Swinging spare tire panel in truck upward to access battery. b. Removing 2 T25 Torx Bit body screws. c. Pulling top battery panel forward and sliding out. 2. Using 10mm Drive Socket, and 12" extension to remove batter ground strap. Raise and support the hood. 3. Remove ECU by: a. Removing right from rim and tire with 17mm heavy duty socket. b. Removing inner wheel well using a 10mm Socket and 1/4" Drive Ratchet and removing push pins with Push Pin Removal Tool. c. Removing two 10mm nuts that hold ECU bracket using 10mm Socket and 1/4" Drive Ratchet inside the fender. d. Swinging ECU and Bracket out and unplugging chassis and engine harness from ECU by sliding tabs. e. Removing 4 T-27 bolts that hold bracket on ECU with a T-27 Torx Bit and 1/4" Drive Ratchet. 2

11 BEFORE MOVING ON, PLEASE FILL OUT THE VEHICLE INFORMATION/TUNE REQUEST FORM AND MAIL THE ECU AND FORM TO 1701 E. EDINGER AVE. SUITE G4, SANTA ANA, CA 92705, USA. ELECTRONIC COMPONENTS SUCH AS THE ECU ARE VERY FRAGILE. PLEASE BE SURE TO SECURELY PACK THE ECU WITH PROTECTIVE COVERING WHEN MAILING. THE VEHICLE INFORMATION/TUNE REQUEST FORM IS INCLUDED WITH THE SUPERCHARGER SYSTEM DOCUMENTATION, AND CAN ALSO BE FOUND AT 4. Remove the air intake system from the vehicle by: a. Removing plastic MAF clips. b. Unplugging both MAF's. c. Removing Mercedes engine cover. d. Removing both air box inlet tubes. e. Unplugging vacuum canister line. f. Using Flat Head Screw Driver or 6.5mm Socket to loosen both Clamps. g. Lifting the air box assemblies from the vehicle. Place all removed parts in a safe location. Many parts will be reused. 5. Remove intake manifold by: 3

12 a. Disconnecting Vacuum line from canister above the intake plenum. b. Removing stock Y inlet from rear section of intake manifold. (Retaining clips on both side of Y must be lifted upwards) c. Unplugging all sensor clips, hoses, and fasteners and make wire harness free for removal. 8 injector clips Rear IAT Sensor clip Fuel pressure sensor clip 2 throttle body clips (Front of manifold) 1 map sensor clip (Front of manifold) 1 Variable runner clip (Front of manifold) Air pump vacuum hose (Front of manifold, On solenoid side NOT manifold side) Variable Runner TB 1 TB 2 MAP d. Removing EVAP line from rear left valve cover and EVAP Silonoid. e. Removing Variable Runner Solenoid from Intake Manifold and storing it for reinstallation during final installation. f. Removing PCV hose with T25 TORX Bit. g. Removing 4 bolts for fuel rail removal. h. Disconnecting fuel line using 14mm Open End Wrench and 17mm Open End Wrench. 4

13 Please be aware that the fuel system may retain fuel pressure that can be extremely dangerous if removed suddenly. Proceed with caution. Please be aware of dripping fuel that may get on parts that can be affected. Please cover fuel line with a shop rag in this case. i. Removing 10 T-45 Torx bolts from intake manifold. j. Lifting intake manifold and setting on work bench. k. Vacuuming area near ports to collect all trapped dust and debris. l. Removing intake manifold gaskets and placing painters tape on runners. 6. Remove power steering reservoir and bracket by: a. Removing all fluid with the use of a fluid evacuator. b. Removing T-25 Torx bolt from reservoir tab. c. Lifting up and disconnecting 2 lines from the front of the engine. (Remove hard lines with reservoir.) d. Use rags to reduce spillage. e. Disconnecting retaining clip for air pump solenoid. f. Removing 4 T-45 bolts and eliminate engine bracket. 7. Remove both rear engine hoist brackets by: a. Removing 3 T-45 Torx bolts from right side of vehicle. b. Cutting harness zip tie from bracket and removing bracket. c. Inserting 2 T-45 Torx bolts to hold dipstick tube to head. (Same location) d. Removing 3 T-45 Torx bolts from left side of vehicle. e. Removing bracket. 8. Remove Throttle bodies by: a. Placing intake manifold on clean work bench. b. Removing map sensor with T-30 Torx Bit. (2 Bolts) c. Detaching wire harness from the front of the intake manifold. 5

14 d. Flipping manifold upside down, and removing 12 T-30 Torx bolts. T-30 e. Inserting flat head screw driver between lower pan, and manifold plate and gently prying to open. 6

15 f. Pulling rubber wire bulk head through hole. g. Using T-30 Torx bit, and removing 4 bolts per throttle body, and 2 metal wire clamps. h. Removing evaporative lines from each throttle body, as well as both horns by unclipping from the side. i. Bolting complete assembly back together to ensure safe storage. 7

16 j. Remove four airbox balls using a 10mm deep wall socket and 1/4" drive. (Store in safe location, will be used soon) f. At this point you will need to gather two (2) throttle bodies, two (2) throttle body gaskets, one (1) throttle body harness, one (1) runner solenoid, one (1) 8

17 map sensor, and one (1) IAT Sensor. These items will be reused on the supercharger system.removing plastic cover by turning 2 tabs 90 degrees and lifting. g. Removing ECU and cage with a T-30 Safety Torx Bit and a 3/8" ratchet. Unplugging chassis and engine harness from ECU by sliding tabs. Before removing battery terminal, double check vehicle is in Park, and driver side window is completely down. 9. Disconnect the Negative battery terminal by: d. Swinging spare tire panel in truck upward to access battery. e. Removing 2 T25 Torx Bit body screws. 9

18 f. Pulling top battery panel forward and sliding out. 10. Using 10mm Drive Socket, and 12" extension to remove batter ground strap. Raise and support the hood. 11. Remove ECU by: h. Removing right from rim and tire with 17mm heavy duty socket. i. Removing inner wheel well using a 10mm Socket and 1/4" Drive Ratchet and removing push pins with Push Pin Removal Tool. j. Removing two 10mm nuts that hold ECU bracket using 10mm Socket and 1/4" Drive Ratchet inside the fender. k. Swinging ECU and Bracket out and unplugging chassis and engine harness from ECU by sliding tabs. l. Removing 4 T-27 bolts that hold bracket on ECU with a T-27 Torx Bit and 1/4" Drive Ratchet. BEFORE MOVING ON, PLEASE FILL OUT THE VEHICLE INFORMATION/TUNE REQUEST FORM AND MAIL THE ECU AND FORM TO 1701 E. EDINGER AVE. SUITE G4, SANTA ANA, CA 92705, USA. ELECTRONIC COMPONENTS SUCH AS THE ECU ARE VERY FRAGILE. PLEASE BE SURE TO SECURELY PACK THE ECU WITH PROTECTIVE COVERING WHEN MAILING. 10

19 THE VEHICLE INFORMATION/TUNE REQUEST FORM IS INCLUDED WITH THE SUPERCHARGER SYSTEM DOCUMENTATION, AND CAN ALSO BE FOUND AT Remove the air intake system from the vehicle by: h. Removing plastic MAF clips. i. Unplugging both MAF's. j. Removing Mercedes engine cover. k. Removing both air box inlet tubes. l. Unplugging vacuum canister line. m. Using Flat Head Screw Driver or 6.5mm Socket to loosen both Clamps. n. Lifting the air box assemblies from the vehicle. Place all removed parts in a safe location. Many parts will be reused. 13. Remove intake manifold by: m. Disconnecting Vacuum line from canister above the intake plenum. n. Removing stock Y inlet from rear section of intake manifold. (Retaining clips on both side of Y must be lifted upwards) o. Unplugging all sensor clips, hoses, and fasteners and make wire harness free for removal. 8 injector clips Rear IAT Sensor clip Fuel pressure sensor clip 11

20 2 throttle body clips (Front of manifold) 1 map sensor clip (Front of manifold) 1 Variable runner clip (Front of manifold) Air pump vacuum hose (Front of manifold, On solenoid side NOT manifold side) Variable Runner TB 1 TB 2 MAP p. Removing EVAP line from rear left valve cover and EVAP Silonoid. q. Removing Variable Runner Solenoid from Intake Manifold and storing it for reinstallation during final installation. r. Removing PCV hose with T25 TORX Bit. s. Removing 4 bolts for fuel rail removal. t. Disconnecting fuel line using 14mm Open End Wrench and 17mm Open End Wrench. Please be aware that the fuel system may retain fuel pressure that can be extremely dangerous if removed suddenly. Proceed with caution. Please be aware of dripping fuel that may get on parts that can be affected. Please cover fuel line with a shop rag in this case. u. Removing 10 T-45 Torx bolts from intake manifold. v. Lifting intake manifold and setting on work bench. w. Vacuuming area near ports to collect all trapped dust and debris. 12

21 x. Removing intake manifold gaskets and placing painters tape on runners. 14. Remove power steering reservoir and bracket by: g. Removing all fluid with the use of a fluid evacuator. h. Removing T-25 Torx bolt from reservoir tab. i. Lifting up and disconnecting 2 lines from the front of the engine. (Remove hard lines with reservoir.) j. Use rags to reduce spillage. k. Disconnecting retaining clip for air pump solenoid. l. Removing 4 T-45 bolts and eliminate engine bracket. 15. Remove both rear engine hoist brackets by: f. Removing 3 T-45 Torx bolts from right side of vehicle. g. Cutting harness zip tie from bracket and removing bracket. h. Inserting 2 T-45 Torx bolts to hold dipstick tube to head. (Same location) i. Removing 3 T-45 Torx bolts from left side of vehicle. j. Removing bracket. 16. Remove Throttle bodies by: k. Placing intake manifold on clean work bench. l. Removing map sensor with T-30 Torx Bit. (2 Bolts) m. Detaching wire harness from the front of the intake manifold. 13

22 n. Flipping manifold upside down, and removing 12 T-30 Torx bolts. T-30 o. Inserting flat head screw driver between lower pan, and manifold plate and gently prying to open. 14

23 p. Pulling rubber wire bulk head through hole. q. Using T-30 Torx bit, and removing 4 bolts per throttle body, and 2 metal wire clamps. r. Removing evaporative lines from each throttle body, as well as both horns by unclipping from the side. s. Bolting complete assembly back together to ensure safe storage. 15

24 t. Remove four airbox balls using a 10mm deep wall socket and 1/4" drive. (Store in safe location, will be used soon) 16

25 At this point you will need to gather two (2) throttle bodies, two (2) throttle body gaskets, one (1) throttle body harness, one (1) runner solenoid, one (1) map sensor, and one (1) IAT Sensor. These items will be reused on the supercharger system. II. Bumper and Underbody Removal 17

26 1. Safely place vehicle on vehicle hoist or stands. 2. Remove belly pan, and bumper shrouds by: a. Using 8mm Socket and 1/4" Drive to remove complete underbody and set in a safe location. b. Using Push Pin Removal Tool, remove five pins from left and right side wheel well and underbody. (Total varies on build date.) c. Removing turn signal light on left and right side of bumper. d. Using an 8mm Ratcheting Wrench, remove both bolts inside Signal hole. e. Using 8mm Socket, 12" long 1/4" extension, and 1/4" Drive, remove top bumper bolts between headlight mount and grill. f. Removing grill support using 8mm Socket from radiator support. g. Pulling both side grills from the bottom of the bumper to gain access. h. Using 8mm Socket, 12" long 1/4" extension, and 1/4" Drive, remove bolt from either side of lower grill in corner. i. With the help of one more person, slide bumper forward and disconnect headlight sprayers. j. Setting bumper in a safe location. k. Removing center oil cooler shroud l. Removing oil cooler side mounts with a 10mm Socket and 1/4 Drive. m. Shrouding and oil cooler side mounts (above) will be completely removed from vehicle at this point. 18

27 Oil cooler will be mounted to heat exchanger in steps ahead. 19

28 III. Cradle Install and Air Tube Delete 1. Install Cradle assembly by: a. Removing air pump valves using a T30 bit b. Removing air pump tubes using an E10 bit. c. Remove the indicated bolt from the left side air pump valve and drill through the bolt hole with an 6mm drill bit. 20

29 d. Remove the indicated bolt from the right side air pump valve and drill half way through the hole from the bottom. Do not drill through the threads in the top half of the air pump valve 21

30 Keep Threads Intact e. Use a M6 x 1.0 tap to tap the threads from the bottom of the right side air valve. f. Bolt air pump valves together, right side valve on top of the left side valve using the included M6x1x30 Button head cap screw, as shown below 22

31 g. Use a hack saw to cut off the mounting tab from the right side air valve shown below h. Bolt the air pump valves to the engine in the location where the left side air valve was removed from and bolt the metal air tube back onto the left side air valve i. Connect the Air Tube and air valve vacuum lines 23

32 j. Use included hose and adapter fittings to connect the right side metal air tube to the right side air valve in its new location. The Straight adapter bolts onto the right side metal air tube and the Bent adapter bolts to the right side air valve. Cut the included hose to proper length and use the included clamps on each end of the hose. 24

33 k. Clean block surface where existing power steering reservoir mounted. l. Positioning the cradle in the front of the engine as shown m. Insert one M8x1.25x25mm bolt through the left hole on top of the cradle and partially thread them. Do not tighten the bolt yet 25

34 Insert bolt into this hole. A bolt is not used in the other hole to make servicing the supercharger in the future easier. n. Bolt on Belt Wrap Idler using the M8x1.25x90mm bolts to the front of the cradle. Partially thread them in. Installation of the belt wrap idler is shown in this illustration 26

35 o. Tighten all three bolts using a 6mm hex bit starting with the top bolt then tighten the front bolts. Torque to 20 ft-lbs p. Removing existing serpentine belt using a 17mm 3/8" deep socket and a 3/8" drive onto belt tensioner. q. Removing all idlers pulleys, water pump pulley and the factory belt tensioner. (Please view Belt Routing Diagram for further information on which pulleys are replaced with new billet parts) r. Installing all idler pulleys with retaining clip facing radiator in the locations shown in the belt routing diagram below 27

36 Belt Routing Diagram: 65mm Idler 65mm Idler Grooved Idler 54mm Idler Water Pump Pulley Tensioner Idler 28

37 a. Using supplied M8x22mm allen hex bolt and bearing washer on tensioner pulley onto supplied Weistec High Rate Tensioner and M8x40mm allen hex bolts and black bearing washers on the rest of the idlers. Install Weistec High Rate Tensioner in place of the factory belt tensioner. Install Weistec Water Pump Pulley using included hardware (Be sure to retain factory spacer on the idler pulley above the crankshaft pictured below) Do not forget factory spacer for this Idler Make Sure All Idlers Are Installed With The Retaining Clip Facing the Radiator. Stock Tensioner Idler: 29

38 Billet Tensioner Idler Installed Using Supplied Washer and Bolt: Installing included serpentine belt around newly added supercharger pulley. 30

39 31

40 IV. Weistec M156 Supercharger Installation Always keep your work area clean for this process. 1. Install Supercharger System by: a. Removing Supercharger from Box A and clean and dust or debris from system. b. Removing runner cover tags, and all vacuum port plastic covers. Do NOT remove throttle body covers. c. Removing painters tape from ports and double check a clean surface. d. Placing new (Included) intake manifold gaskets on head surface. e. Clocking water manifold ports (Rear of Supercharger system) at a 10 o'clock and 2 o'clock position. (Do not tighten clamping bolts until you are sure water lines will clear near firewall) f. Installing the following vacuum lines before installation: Air pump vacuum line on lowest vacuum port for Stage 1 and Stage 2 vehicles, For Stage 3 the 1/8 port must be securely plugged or capped Long 3/8" EVAP line. (Keep coiled on top of supercharger unit) 10" 1/2" brake boost line with crimp style clamp. 32

41 g. Installing existing map sensor using 5mm Allen Bit. Socket head allen bolts used for map sensor and PCV in rear Y inlet. h. Unclipping injectors from existing fuel rails, and inserting into new fuel rails with clips. (Be sure to use some lubrication to insert into fuel rails and supercharger, failure to do so can result in damage to O rings) 33

42 i. Install the IAT (Intake Air Temperature) Sensor in the rear of the supercharger system. MAP Sensor IAT Sensor j. With the help of a technician, lift supercharger system and carefully place it into its position. Fitment should be very snug and clean. Be sure to lower the Supercharger slowly as to not damage the gaskets. 34

43 k. Using the included new stainless socket Allen bolts, insert all ten and tighten snug. Torque bolts in a start pattern to Lb. Ft. (25 Nm) l. Twisting existing brake booster line towards supercharger unit, and placing included crimp style clamp on 1/2" brake booster hose and slide over existing line. Adjust line and double check no bottle necks in line. Crimp clamp at this point. m. Installing new fuel rails and injectors onto supercharger unit buy using 4mm Allen bit and 1/4" drive. Aluminum finish spacers will be used between manifold and fuel rail. 35

44 n. Running new fuel line crossover behind Y inlet. (45 end must be on right side of vehicle) o. Using 7/8" wrench, tight both fuel line ends. p. Replacing existing harness zip ties with included zip ties. Cut excess and dispose. Cut MAP sensor plug here and extend q. Carefully cutting 3 wire map sensor wire about 1.5" away from plug and crimping new extension. Use included heat shrink on all crimp joints and be sure to have no wiring or metal showing through. Use 3/8" heat shrink over all three wires. Clip plug in rear of Y inlet. 36

45 New MAP Sensor Plug Location r. Clipping existing throttle body harness. (Two plugs) s. Plugging in Variable Runner and Air Pump Solenoids to the engine harness. Variable Runner Solenoid will have no vacuum lines connected to it. Air Pump Solenoid will re-use factory vacuum lines for Stage 1 and Stage 2 cars. Stage 3 cars the solenoid will only be plugged into the engine harness. Cable ties should be used to secure the solenoid in place. Solenoid Cable tied to harness under air box 37

46 t. Installing existing PCV line in rear section of Y Inlet using a 5mm Allen key. Twisting hose can be necessary for proper seal. Shown Above is the PCV hose correctly positioned for installation. u. Installing existing airbox balls on included stand-off's using a 10mm open end wrench, and a 10mm deep wall socket and 1/4" drive. v. Running 3/8" EVAP hose along coil pack wiring harness and using crimp style clamp onto EVAP solenoid. Use included zip ties to hold in place of existing EVAP line. 38

47 V. Intercooler System Installation and Plumbing 1. Install Intercooler recovery tank by(skip this Section if installing Weistec Trunk Ice Tank, Refer to Trunk Tank Manual for hose routing): a. Removing two existing timing cover bolts on right side using a T-30 Torx Bit and 3/8" drive. Remove b. Removing wire harness on right side. c. Mounting tank using 5mm Allen Bit and 1/4" Drive against timing cover with spacers. 39

48 d. Installing lines onto reservoir and fastening included clamps with crimp style clamp tool. (More pictures of this procedure below). 2. Install Water Pump by: a. Using a 5mm Drill Bit and a Drill, drill two holes through bumper support. 1 1/4" 1/2" b. Using two supplied body bolts, use a 10mm Socket and 1/4" Drive Ratchet to screw in place. 40

49 c. Mounting pump onto bracket by using a 12mm Open End Wrench to screw bolts in place, and Using a 13mm Open End Wrench to install supplied M8 Serrated nuts on back side of bracket. 3. Install Heat Exchanger by: a. Cutting along white lines with an angle grinder to properly fit with heat exchanger. 41

50 b. Trimming around shrouding to properly fit oil lines. Trim here with Aviation snips a. Installing metal brackets back onto vehicle and pushing oil cooler pins in top grommets and shifting bottom grommets behind bracket to give the oil cooler a more straight and flush mount. (This will leave room for the Heat Exchanger.) b. Using a 5mm Drill Bit and a Drill, drill four holes on marks through bumper support. c. Using four included body bolts, use a 10mm Socket and 1/4" drive to screw in place. 4. Install Intercooler hoses by: 42

51 a. Placing included clamps on both ends of the short straight hose. Cut to length approximately 11-12". b. Placing included clamps on both ends of L-shaped molded hose and installing from heat exchanger to the bottom o the recovery tank. c. Placing included clamps on both ends of straight 3/4" hose and running from water pump to the rear of the supercharger. (Be sure to tighten rear 43

52 supercharger fitting at this point with a 1" Open End Wrench.) Cut hose to length on supercharger side. d. Placing included clamps on both ends of straight hose and installing from intercooler reservoir to back side of supercharger system. Zip Tie water line to radiator hose and keep clear of fan shroud. (Be sure to tighten water outlet nut before moving forward with a 1" Open End Wrench) Cut hose to length on supercharger side. 44

53 Double Check all fitments of hoses and assure no bottle neck or kink in hose. This will greatly reduce flow and performance of system. Also double check all hoses are not lying against sharp objects. 5. Install Water Pump Wiring by: a. Using 10mm Socket and 1/4" Drive, remove ground nut from left side wheel well, and place included harness ground and retighten. b. Running wire along body wiring up to fuse box. c. Using zip ties from water pump along with body wiring. d. Plugging harness and water pump together. e. Run Blue switched line to open connector in fuse box. 45

54 Run red power line to open connector in fuse box. 46

55 VI. Bumper and Underbody Installation 1. Install Bumper by: a. Replugging all head light electrical clips. b. Reinstalling bumper cover using an 8mm Socket, 12" Extension, 1/4" Drive and 8mm Ratcheting Wrench. c. Reinstall grill support using a 8mm Socket and 1/4" Drive onto radiator support. d. Lift car on hoist and reinstall underbody using an 8mm Socket and 1/4" Drive and reinserting all push pins. (Ten total) 47

56 VII. Supplementary Installation and Fluid Check 1. Install existing fuel line by: a. Removing line from existing fuel rails with a 17mm Open End Wrench. b. Installing onto new fuel rails using a 17mm Open End Wrench on the fuel rail side, and install onto chassis side using a 17mm Open End Wrench and 14mm Open End Wrench. 2. Install Throttle Bodies by: a. Placing throttle bodies in vice. b. Tapping existing hole with supplied 1/8" NPT Tap. 48

57 c. using pipe sealant, place NPT plug into hole. d. Removing protective film from throttle body inlets. e. Placing included bolts into throttle body with existing gasket and fastening in star formation on both sides. f. Run existing throttle body wiring behind supercharger Y inlet and plug into both throttle bodies. 3. Install factory air boxes by: a. Installing included black couplers and clamps on throttle body side. b. Fastening clamps on throttle body side. c. Freely placing existing air box couplers over coupler, install factory air boxes. d. Fasten clamps on air box side. e. Install air box inlets. 4. Install ECU by: a. Inserting ECU into the fixture. b. Clipping Chassis and engine harness and sliding clips to ensure proper plug in. c. Reinstalling onto bracket and sliding in fender. d. Gently bolting it down with 10mm Socket and 1/4" Drive Ratchet. 49

58 5. Final assembly: a. Plug in electrical connections for the Variable Runner Solenoid and Air Injection Solenoid. Solenoids must be plugged in to prevent check engine lights and other issues. Position solenoids in secure locations on the intake manifold and use cable ties to hold them in place b. Add water into intercooler system and double check no leaks. c. Reinstall battery ground using a 10mm Socket and 1/4" Drive. d. Reinstall battery cover. e. Check all vital fluids. f. Turn Key to on position and add water into intercooler system until system is fully bled and water is visibly circulating. 6. Fill supercharger with oil by: 50

59 a. Removing plug on top of supercharger with a 5mm allen bit. b. Filling supercharger unit with supplied oil. Weistec Engineering recommends adding coolant / anti-freeze to the intercooler system if climate temperatures reach freezing. 51

60 7. Bleed Power Steering System by: a. Making sure that power steering lines are properly routed, sloping down from the reservoir to the power steering pump b. Loosening Power Steering Reservoir Cap, wrapping a shop rag around the cap in case of over flow. c. Starting engine d. Turning steering wheel from lock to lock 2 to 3 times. e. Checking power steering fluid level, adding fluid if necessary f. Repeating steps d and e until power steering system is functioning properly and quietly g. Tightening Power Steering Reservoir Cap 52

61 Thank you from Weistec Engineering! Always enjoy the added horsepower and torque of the M156 supercharger responsibly. Use best judgment when driving, and remember to have fun! NOTES: 53

CLS63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2

CLS63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2 CLS63 Weistec M156 Supercharger System Installation Guide Stage 1 / Stage 2 WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 63 USES AN ELECTRONIC THROTTLE

More information

Weistec M113K Supercharger System Installation Guide

Weistec M113K Supercharger System Installation Guide Weistec M113K Supercharger System Installation Guide WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 55 USES AN ELECTRONIC THROTTLE CONTROL (ETC), WHICH

More information

C63 Weistec M156 Supercharger System Installation Guide Stage 3

C63 Weistec M156 Supercharger System Installation Guide Stage 3 C63 Weistec M156 Supercharger System Installation Guide Stage 3 WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 63 USES AN ELECTRONIC THROTTLE CONTROL

More information

CLK63 (Black Series) Weistec M156 Supercharger System Installation Guide Stage 3

CLK63 (Black Series) Weistec M156 Supercharger System Installation Guide Stage 3 CLK63 (Black Series) Weistec M156 Supercharger System Installation Guide Stage 3 WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER. THE AMG 63 USES AN ELECTRONIC

More information

SLS825 Weistec Supercharger System Installation Guide

SLS825 Weistec Supercharger System Installation Guide SLS825 Weistec Supercharger System Installation Guide 2010-Present SLS AMG (Gullwing and Roadster) 2014 SLS Black Series WARNING! DO NOT HAVE YOUR ECU REPROGRAMMED ANYWHERE BUT AT WEISTEC FOR THIS SUPERCHARGER.

More information

Weistec True Downpipes

Weistec True Downpipes Weistec True Downpipes Installation Guide, W212, W218, AWD 2014+ E63 2014+ CLS63 WARNING! IF YOU ARE NOT EXPERIENCED IN THE AREA OF AUTOMOTIVE MECHANICS, WE STRONGLY URGE THAT YOU REFER THIS INSTALLATION

More information

Weistec M156/M159 ENGINE

Weistec M156/M159 ENGINE Weistec M156/M159 ENGINE Oil / Air Separator System Installation Guide 2007-2011 S63 AMG 2007-2011 ML63 AMG 2007 R63 AMG 2007-2008 CLK63 AMG 2008 CLK63 Black Series 2007-2011 CLS63 AMG 2008-Present C63

More information

Weistec M157 WMI System

Weistec M157 WMI System Weistec M157 WMI System Installation Guide 2012-2013 E63 2014+ E63 4matic(S) 2011-2013 CLS63 2014+ CLS63 4matic(S) 2015+ S63 AMG (Without ABC Suspension) This product is legal in California for racing

More information

Weistec M177 WMI System

Weistec M177 WMI System Weistec M177 WMI System Installation Guide 2015+ C63(S) Sedan 2016+ C63(S) Coupe This product is legal in California for racing vehicles only and should never be used upon a highway. This product is legal

More information

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Procharger Stage II Intercooled Supercharger System (11-14 GT) Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2

More information

ENGINE DEVELOPMENT INC.

ENGINE DEVELOPMENT INC. 2003 Ford Expedition 4.6L& 5.4L We encourage you to read this manual thoroughly before you begin work, and perform the following: 1. A quick parts check to make certain your kit is complete. If you discover

More information

Edelbrock E-Force Supercharger Part #1538: Dodge 1500 Truck 5.7L V8 HEMI

Edelbrock E-Force Supercharger Part #1538: Dodge 1500 Truck 5.7L V8 HEMI Edelbrock E-Force Supercharger Part #1538: 2009-2014 Dodge 1500 Truck 5.7L V8 HEMI 2009-14 Dodge 5.7L Hemi 1500 Truck INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the 2009-15

More information

2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit

2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit 2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is

More information

IAG Street Series Air / Oil Separator (AOS) For 2017 WRX

IAG Street Series Air / Oil Separator (AOS) For 2017 WRX P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,

More information

IAG Street Series Air / Oil Separator (AOS) For WRX

IAG Street Series Air / Oil Separator (AOS) For WRX P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

IAG Competition Series Air / Oil Separator (AOS) For WRX

IAG Competition Series Air / Oil Separator (AOS) For WRX P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw

More information

97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS

97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS 92RC60500 97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS Congratulations on your purchase of a new Rough Country 2 /3 Body Lift. We are committed to providing you with the best product available for the best

More information

2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED

2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE

More information

Performance Inlet Manifold

Performance Inlet Manifold Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with

More information

SLP Camaro ZL1 STAGE 3 (650 HP)

SLP Camaro ZL1 STAGE 3 (650 HP) SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1

More information

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit # 2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009

More information

Installation Instructions for: Radix. INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha

Installation Instructions for: Radix. INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha Installation Instructions for: Radix INTERCOOLED SUPERCHARGER SYSTEM 2008 Hummer H3-Alpha Step-by-step instructions for installing the best in supercharger systems. ATTENTION! Your MAGNA CHARGER intercooler

More information

Edelbrock LS2 Corvette Supercharger Part #1593, 1594 & 1595

Edelbrock LS2 Corvette Supercharger Part #1593, 1594 & 1595 Edelbrock LS2 Corvette Supercharger INTRODUCTION Thank you for purchasing the Edelbrock 6.0L GM Supercharger System for the Chevy Corvette. The Edelbrock E-Force Supercharger System for the 2005 to 2007

More information

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines Part #7179

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines Part #7179 For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your

More information

Instant Chat off the main page of Or simply call our tech team at

Instant Chat off the main page of   Or simply call our tech team at FRONT MOUNT INTERCOOLER 2008-13 STI 2014-04- 08 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation

More information

Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI

Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following

More information

Edelbrock LS3 Corvette Supercharger Part #1590, 1591 & 1592

Edelbrock LS3 Corvette Supercharger Part #1590, 1591 & 1592 Edelbrock LS3 Corvette Supercharger Part #1590, 1591 & 1592 INTRODUCTION Thank you for purchasing the Edelbrock 6.2L GM Superchager System for the Chevy Corvette. The Edelbrock E-Force Supercharger System

More information

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat

More information

2015 Corvette Supercharger System Instructions

2015 Corvette Supercharger System Instructions 2015 Corvette Supercharger System Instructions These instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharging system. Please be sure to use all safety equipment

More information

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace

More information

Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions

Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,

More information

LChevrolet Camaro Supercharger Kit

LChevrolet Camaro Supercharger Kit PART #92000A Important Notes: 2010-2013 6.2LChevrolet Camaro Supercharger Kit The use of fuel additives (ie. octane boosters) is not recommended. There is a possibility that these chemicals can damage

More information

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located

More information

Wrenches: ⅞, 8mm, 10mm, 13mm, 19mm P. allen, Other: Electrical Tape

Wrenches: ⅞, 8mm, 10mm, 13mm, 19mm P. allen, Other: Electrical Tape IAG Street Series Air / Oil Separator (AOS) For 2008-14 STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat

More information

Edelbrock 5.4L F-150 Supercharger Part #1583

Edelbrock 5.4L F-150 Supercharger Part #1583 Edelbrock 5.4L F-150 Supercharger INTRODUCTION Edelbrock 5.4L Ford Supercharger System Thank you for purchasing the Edelbrock 5.4L Ford Supercharger System for the F-150. The Edelbrock E-Force Supercharger

More information

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles) P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,

More information

Phone Fax

Phone Fax Directions for Installation of ECS Paxton Supercharger Kit Disconnect battery Remove stock serpentine belt Remove stock belt tensioner, save the 2 bolts for later use on supercharger bracket Remove alternator

More information

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat

More information

Single Barrel Shotgun HPFP Install Guide

Single Barrel Shotgun HPFP Install Guide Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should

More information

Edelbrock E-Force Supercharger Dodge/Chrysler 5.7L and 6.4L HEMI Part #1534, 1535, and 15350

Edelbrock E-Force Supercharger Dodge/Chrysler 5.7L and 6.4L HEMI Part #1534, 1535, and 15350 Edelbrock E-Force Supercharger 2011-2013 Dodge/Chrysler 5.7L and 6.4L HEMI Part #1534, 1535, 15340 and 15350 PLEASE COMPLETE THIS PROCEDURE PRIOR to starting the installation of your E-Force supercharger

More information

Edelbrock Hemi Supercharger Part #1530, 1531, 1532, 1533, 1536 & 1537

Edelbrock Hemi Supercharger Part #1530, 1531, 1532, 1533, 1536 & 1537 Edelbrock Hemi Supercharger INTRODUCTION Thank you for purchasing the Edelbrock Hemi Supercharger System for various Chrysler/Dodge vehicles. The Edelbrock E-Force Supercharger System for the 2005 to 2010

More information

Always wear safety glasses when working on your vehicle.

Always wear safety glasses when working on your vehicle. 90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively

More information

APR, LLC

APR, LLC + 1. 3 3 4. 5 0 2. 5 1 8 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 + 1. 3 3 4. 5 0 2. 5 1 8 1 NOTES:

More information

Installation Instructions for: HOT ROD SUPERCHARGER SYSTEM

Installation Instructions for: HOT ROD SUPERCHARGER SYSTEM Installation Instructions for: HOT ROD SUPERCHARGER SYSTEM 89-89-57-007 Step-by-step instructions for installing the best in supercharger systems. Magnuson Products Inc 1990 Knoll Drive, Ventura, CA. 93003

More information

Installation Instructions for: Toyota 4Runner and FJ Cruiser

Installation Instructions for: Toyota 4Runner and FJ Cruiser Installation Instructions for: 2010-2017 Toyota 4Runner and 2010-2014 FJ Cruiser Step-by-step instructions for installation of the supercharger system. * PREMIUM GASOLINE FUEL REQUIRED * ATTENTION! Your

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT

SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT = SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,

More information

Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide

Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Congratulations on your new upgraded piping and intercooler kit, this kit has proven to provide the lowest intake air temps to date on our

More information

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179 For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your vehicle.

More information

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *

More information

Edelbrock E-Force Supercharger Ford F L Lincoln Mark LT 5.4L Part #1581

Edelbrock E-Force Supercharger Ford F L Lincoln Mark LT 5.4L Part #1581 Edelbrock E-Force Supercharger 2004-08 Ford F-150 5.4L Part #1581 INTRODUCTION Thank you for purchasing the Edelbrock 5.4L Ford Supercharger System for the 2004-2008 F-150 and 2006-2008 Lincoln Mark LT.

More information

Owner smanual. Banks Monster-Ram Intake and Grid Heater Delete Kit. For Racing Only Ram 6.7L Pickup Trucks. with Installation Instructions

Owner smanual. Banks Monster-Ram Intake and Grid Heater Delete Kit. For Racing Only Ram 6.7L Pickup Trucks. with Installation Instructions with Installation Instructions Owner smanual Banks Monster-Ram Intake and Grid Heater Delete Kit For Racing Only 2007-2017 Ram 6.7L Pickup Trucks THIS MANUAL IS FOR USE WITH SYSTEM 42788, 42788-PC, 42790,

More information

INSTALLATION INSTRUCTIONS CATCH CAN KIT

INSTALLATION INSTRUCTIONS CATCH CAN KIT INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT

More information

Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM

Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM 1996-2002 4Runner 1997-1998 T100 1997-2004 Tacoma 2000-2003 Tundra * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg

More information

Edelbrock 5.0L Mustang GT Supercharger Part #1588 & 1589

Edelbrock 5.0L Mustang GT Supercharger Part #1588 & 1589 Edelbrock 5.0L Mustang GT Supercharger Part #1588 & 1589 INTRODUCTION Edelbrock 5.0L Ford Supercharger System Thank you for purchasing the Edelbrock 5.0L Ford Supercharger System for the Mustang GT. The

More information

IAG Air / Oil Separator (AOS) For STi

IAG Air / Oil Separator (AOS) For STi IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,

More information

2015+ EcoBoost F150 & Raptor Intercooler Install

2015+ EcoBoost F150 & Raptor Intercooler Install 2015+ EcoBoost F150 & 2017+ Raptor Intercooler Install Note: This entire job can be performed with the truck on the ground - No need to raise the vehicle. The most difficult part is removing the grille

More information

BBK Intake Manifold Kit ( L) - Installation Instructions

BBK Intake Manifold Kit ( L) - Installation Instructions BBK Intake Manifold Kit (86-93 5.0L) - Installation Instructions The below installation instructions work for the following products: BBK Intake Manifold Kit (86-93 5.0L) Please read through the instructions

More information

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS #TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When

More information

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions 96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove

More information

INSTALLATION INSTRUCTIONS CATCH CAN KIT

INSTALLATION INSTRUCTIONS CATCH CAN KIT INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN

More information

Installation manual BMW E TS1/TS2

Installation manual BMW E TS1/TS2 Installation manual BMW E46 330 TS1/TS2 Technical support Europe: +4741558555 Technical support USA: (858)314-2954 Email support: support@esstuning Installation manual BMW E46 330 TS1/TS2 Remove and send

More information

INTERCOOLED SUPERCHARGER SYSTEM FORD 5.4L 3V F-150 TRUCK

INTERCOOLED SUPERCHARGER SYSTEM FORD 5.4L 3V F-150 TRUCK Installation Instructions for: INTERCOOLED SUPERCHARGER SYSTEM 2004-2006 FORD 5.4L 3V F-150 TRUCK Step-by-step instructions for installing the best in supercharger systems. 89-89-65-001 Rev C Magnuson

More information

APIKOL Ur-S4/S6 Gen. II Front Mount Intercooler INSTALLATION INSTRUCTIONS

APIKOL Ur-S4/S6 Gen. II Front Mount Intercooler INSTALLATION INSTRUCTIONS APIKOL Ur-S4/S6 Gen. II Front Mount Intercooler INSTALLATION INSTRUCTIONS Only work underneath your vehicle after properly supporting it with adequate jack stands on a flat surface. NEVER work under a

More information

FULL LENGTH HEADERS/ CATTED HEAD PIPES

FULL LENGTH HEADERS/ CATTED HEAD PIPES INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder

More information

INSTALLATION INSTRUCTIONS CATCH CAN KIT

INSTALLATION INSTRUCTIONS CATCH CAN KIT INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT

More information

Edelbrock E-Force Supercharger JEEP WRANGLER JK 3.6L V6 Part #1527 and 15270

Edelbrock E-Force Supercharger JEEP WRANGLER JK 3.6L V6 Part #1527 and 15270 Edelbrock E-Force Supercharger 2012-14 JEEP WRANGLER JK 3.6L V6 Part #1527 and 15270 INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the Jeep Wrangler with 3.6L V6 Pentastar.

More information

Slingshot Rotrex Supercharger Kit

Slingshot Rotrex Supercharger Kit Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0907 APPLICATION: 2011-12 E90 335i/xi (N55 engine) with BMW M-Technic bumper and without stock oil cooler Congratulations for being selective enough

More information

Installation Instructions for: Radix. Intercooled Supercharger System GM 4.8L & 5.3L SUV S Only

Installation Instructions for: Radix. Intercooled Supercharger System GM 4.8L & 5.3L SUV S Only Installation Instructions for: Radix Intercooled Supercharger System 07-10 GM 4.8L & 5.3L SUV S Only Step-by-step instructions for installing the best in supercharger systems. * PREMIUM FUEL REQUIRED *

More information

Edelbrock LS7 Corvette Supercharger Part #1572 & 1573

Edelbrock LS7 Corvette Supercharger Part #1572 & 1573 Edelbrock LS7 Corvette Supercharger INTRODUCTION Thank you for purchasing the Edelbrock 7.0L GM Supercharger System for the Chevy Corvette Z06. The Edelbrock E-Force Supercharger System for the 2006 to

More information

137. Unbolt the fi ve bolts holding the coil brackets to the valve covers using a 10mm wrench Remove the coil brackets for modifi cation.

137. Unbolt the fi ve bolts holding the coil brackets to the valve covers using a 10mm wrench Remove the coil brackets for modifi cation. 137. Unbolt the fi ve bolts holding the coil brackets to the valve covers using a 10mm wrench. 138. Remove the coil brackets for modifi cation. 139. Use a small fl athead screwdriver to unsnap the plastic

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter

More information

Included parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Brackets/Hardware

Included parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Brackets/Hardware TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports

More information

03-04 Cobra. Hellion Power Systems Mustang Cobra Kit Instructions

03-04 Cobra. Hellion Power Systems Mustang Cobra Kit Instructions Hellion Power Systems 03-04 Mustang Cobra Kit Instructions NECESSARY PARTS REQUIRED FOR INSTALLATION Necessary: 03-04 Cobra hellion Kit ONLY 99-01 Alternator #YR3210346AA Alternator Bracket #XR3Z-10153-AB

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough

More information

Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench

Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench 2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission

More information

TOP FEED FUEL RAIL KIT for WRX

TOP FEED FUEL RAIL KIT for WRX TOP FEED FUEL RAIL KIT for 2002-14 WRX Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0925 APPLICATION 2011-12 E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler Congratulations for being selective enough

More information

Shotgun Single Barrel HPFP install guide

Shotgun Single Barrel HPFP install guide Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective

More information

OIL COOLER KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION TOOLS NEEDED NOTE INSTALL PROCEDURE

OIL COOLER KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION TOOLS NEEDED NOTE INSTALL PROCEDURE PARTS LIST AND PARTS INCLUDED 3PC APPLICATION-SPECIFIC MOUNTING BRACKETS 1PC HORN RELOCATION MOUNTING BRACKET 1PC 25-ROW OIL COOLER (SLEEK SILVER OR STEALTH BLACK) 1PC 4'4" STAINLESS STEEL BRAIDED HOSE

More information

INSTALLATION INSTRUCTIONS PORT INJECTION KIT (PIK)

INSTALLATION INSTRUCTIONS PORT INJECTION KIT (PIK) INSTALLATION INSTRUCTIONS PORT INJECTION KIT (PIK) FORD FOCUS 2.3L ECOBOOST Document: 19-0155 Support: info@radiumauto.com IMPORTANT NOTES: 1. This installation requires minor metal cutting. Air tools

More information

Edelbrock E-Force Supercharger L HEMI / L HEMI Part #1530, 1531, 1532, 1533, 1536 & 1537

Edelbrock E-Force Supercharger L HEMI / L HEMI Part #1530, 1531, 1532, 1533, 1536 & 1537 Edelbrock E-Force Supercharger 2005-10 6.1L HEMI / 2006-10 5.7L HEMI PLEASE COMPLETE THIS PROCEDURE PRIOR to starting the installation of your E-Force supercharger system. This will allow our calibration

More information

Edelbrock E-Force Supercharger Complete Competition Ford Mustang 5.0L Part # s: 15896

Edelbrock E-Force Supercharger Complete Competition Ford Mustang 5.0L Part # s: 15896 Edelbrock E-Force Supercharger Complete Competition Part # s: 15896 Introduction Thank you for purchasing the Edelbrock Complete Competition Supercharger System for the 2011-2013 5.0L Ford Mustang GT.

More information

Instant Chat off the main page of Or simply call our tech team at

Instant Chat off the main page of   Or simply call our tech team at FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of

More information

FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS

FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # 48.10.90 & 48.10.90P INSTALATION INSTRUCTIONS PART LIST: 1 INTERCOOLER CORE 1 U-BENT TUBE 1 L-SHAPED TUBE 1 INTERCOOLER INLET TUBE 4 M6 NYLOC NUT 3 M6

More information

MAZDASPEED3 Intercooler Instructions

MAZDASPEED3 Intercooler Instructions MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through

More information

Edelbrock LS2 Corvette Supercharger Part #1593, 1594 & 1595

Edelbrock LS2 Corvette Supercharger Part #1593, 1594 & 1595 Edelbrock LS2 Corvette Supercharger E-MAIL EDELBROCK YOUR STOCK VEHICLE CALIBRATION AND VEHICLE INFORMATION PLEASE COMPLETE THIS PROCEDURE PRIOR to starting the installation of your E-Force supercharger

More information

Edelbrock 5.4L Supercharger Ford Expedition & F-150 Lincoln Navigator Part #1583

Edelbrock 5.4L Supercharger Ford Expedition & F-150 Lincoln Navigator Part #1583 Edelbrock 5.4L Supercharger Ford Expedition & F-150 Lincoln Navigator INTRODUCTION Thank you for purchasing the Edelbrock 5.4L Ford / Lincoln Supercharger System for the F-150, Expedition, and Navigator.

More information

Edelbrock LS2 Corvette Supercharger Part #1593, 1594 & 1595

Edelbrock LS2 Corvette Supercharger Part #1593, 1594 & 1595 Edelbrock LS2 Corvette Supercharger TEMPLATE, FAN SHROUD, C6 CORVETTE, LH 1.38 1.00 B 0.35 B 0.35 A A 0.35 A LH A 1.00 FOR VEHICLES EQUIPPED WITH AUX. OIL COOLER, DRILL HOLES MARKED A. LINE UP TEMPLATE

More information

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

Edelbrock E-Force Supercharger Ford F L Lincoln Mark LT 5.4L Part #1581

Edelbrock E-Force Supercharger Ford F L Lincoln Mark LT 5.4L Part #1581 Edelbrock E-Force Supercharger 2004-08 Ford F-150 5.4L Part #1581 INTRODUCTION Thank you for purchasing the Edelbrock 5.4L Ford Supercharger System for the 2004-2008 F-150 and 2006-2008 Lincoln Mark LT.

More information

INSTALLATION INSTRUCTIONS FUEL RAIL

INSTALLATION INSTRUCTIONS FUEL RAIL INSTALLATION INSTRUCTIONS FUEL RAIL MITSUBISHI EVO X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM PREPARING THE VEHICLE:

More information

Parts List See cover Page

Parts List See cover Page Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let

More information

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM

More information

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side 2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and

More information

3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT

3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT Part Number: 00602-17620-260 00602-17620-261 00602-17620-263 00602-17620-264 00602-17620-274 00602-17620-275 00602-17620-276 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description

More information