The Leading Source For Quality Products And Excellent Service!

Size: px
Start display at page:

Download "The Leading Source For Quality Products And Excellent Service!"

Transcription

1 Volume 10 Proud of our Past Focused on the Future OHC Closers Surface Closers Gate Closer Door Hardware Miscellaneous Hardware Strikes Door Holders, Stops & Flush Bolts Thresholds Door Sweeps Aluminum Steel Pivots Stainless Steel Pivots Aluminum Geared Hinges Stainless Steel Pin & Barrel Hinges Butt Hinges & Power Transfers Mechanical - Electrified Exit Devices & Escutcheon Trim Mechanical - Locksets Mechanical - Electrified Mortise Locksets Electro-Magnetic Locks Access Controls The Leading Source For Quality Products And Excellent Service!

2 Overhead Concealed Series 200 & 200SA Underwriters Laboratories Inc. Listed. Two Speed Control Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation DP dual purpose radial ball bearing bottom pivot set is standard for floor or threshold center pivoted installation. Optional 3010-GE bottom pivot sets are available, but must be ordered separately. Fits in an aluminum header or transom bar as small as 1 ¾ x 4. Cast Iron Body. Positive centering for alignment and to hold door closed against a normal wind or draft. Stable hydraulic door check fluid for any climatic operation and constant lubrication. Built-in positive back stop and hold-open positions available: 105 Back Stop with Hold-Open 105 Back Stop - no Hold-Open 90 Back Stop with Hold-Open 90 Back Stop - no Hold-Open S Type Arm Shown. Other Type Top Arms Also Available. Series 200 Handicap & Standard CENTER HUNG DOORS: Double or Single Acting (Door stop applied to frame renders unit Single Acting). Adjustable S type side loading, A type, K type or PT type end loading arms are available for center pivoted applications. OFFSET HUNG DOORS: Single Acting. Offset JO and VO type top arms are available for butt hinge or offset pivot applications. ADA (Handicap) spring tensions available for use on center pivoted applications. Standard spring tensions available: ADA, LIGHT, MEDIUM, and HEAVY Closers designed for ALL GLASS DOORS with a longer spindle and short arm. Series 200-SA All Glass Door Closer CENTER HUNG DOORS: Double or Single Acting Door (Door stop applied to frame renders unit Single Acting). A type short end loading top arm supplied for smaller top rail applications. ¾ spindle length for better door support ¾ spindle length for better door support. Standard spring tensions available: MEDIUM or HEAVY 5-¾ Short A Arm (measured from center line of spindle to end of arm). 2 West: Fax:

3 Overhead Concealed Series 300 & 500 ADA (Handicap) multi-sized closer with Adjustable Spring Power Barrier Free Operation to comply with Federal Accessibility Standards (ADA) ANSI A Underwriters Laboratories Inc. Fire Endurance Tested, conforming to UL10C and UBC7.2 (1997) for Fire Safety. Suitable for both Center Hung (Double or Single Acting) and Offset Doors. Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation. S type side loading, A type, K type, or PT type end loading top arms are available for center pivoted applications. Offset JO and VO type top arms are available for butt hinge or offset pivot (may not meet handicap force requirements) DP dual purpose radial ball bearing bottom pivot set is standard for floor or threshold center pivoted installation. Optional 3010-GE bottom pivot sets are available, but must be ordered separately. Fits in an aluminum header or transom bar as small as 1 ¾ x 4. Stable hydraulic door check fluid for any climatic operation and constant lubrication. Series 300 Handicap Adjustable Spring Power ADA (Handicap) multi-sized closer with Adjustable Spring Power for a range of sizes from 8½ lbs. of Opening Force to medium spring tension, and fully adjustable after installation. Built-in positive back stop and hold-open positions available: 105 Back Stop with Hold-Open 105 Back Stop - no Hold-Open 90 Back Stop with Hold-Open 90 Back Stop - no Hold-Open Series CERTIFIED GRADE 1 Adjustable Spring Power Factory tested to meet or exceed ANSI Grade 1 ADA (Handicap) multi-size closer with Adjustable Spring Power for a range of sizes from 5 lb. to Medium Spring Tension, fully adjustable after installation Underwriters Laboratories Inc. Fire Endurance Tested, conforming to UL10C and UBC7.2 (1997) for Fire Safety. Built-in positive back stop and hold-open positions available: 105 Back Stop with Hold-Open 105 Back Stop - no Hold-Open 90 Back Stop with Hold-Open 90 Back Stop - no Hold-Open East: Fax:

4 Surface Closers Model 44CI & 5000 Model 44CI Adjustable Spring Power Application for HIGH TRAFFIC doors Cast Iron Body; Forged Steel Arm Double Heat Treated Steel Pinion All Weather Fluid Non-handed Adjustable 1 through 6; Standard with Back-Check Universal application for Regular Arm, Top Jam, or Parallel Arm mounting Standard Plastic Cover - non handed 10 year warranty Attractive baked enamel finishes: AL - Aluminum DU - Storefront Bronze Optional Features Metal Cover Hold-open arm Stop only arm Compliance Standards ANSI/BHMA A156.4 Grade 1 Certified UL/C-UL Listed UL 10B and UL 10C Compliant for positive pressure Certified to conform to UBC 7-2 (1997, UL 228) Barrier Free Operation to comply with Federal Accessibility Standards (ADA); complying with ANSI A117.1 ( ) Series Series With Dress Cover 5050 Series Without Dress Cover ADA (Handicap) multi-sized closers with adjustable spring power for a range of sizes adjustable after installation: 5001 & 5051: 8 ½ lb. opening force to a size & 5052: 5 lb. opening force to a size & 5053: 5 lb. opening force to a size 4 CLOSER FUNCTIONS: 5001 & 5051; adjustable spring power with adjustable Back-Check controlled by a separate regulating valve, adjustable after installation & 5052; adjustable spring power with adjustable delayed closing action controlled by a separate regulating valve, adjustable after installation & 5053; Basic-adjustable spring power only. 4 West: Fax:

5 Surface Closers Series 800 & 1800 Underwriters Laboratories Inc. Listed Two Speed Control Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation. Universal Application: Non-handed for standard, top jamb or parallel arm installation. Rack and pinion mechanism contained in a high tensile precision cast aluminum housing. Stable hydraulic door check fluid for any climatic operation and constant lubrication. Furnished with regular, hold-open or fusible link hold-open arms. Hold-open arms are adjustable for holding from 90 to 180. Attractive Baked Enamel finishes: AL - Aluminum DU - Storefront Bronze Series 800 Standard Series 850 Adjustable Back-Check Series 880 Range of sizes: Standard : 851, 852, 853, 854, and 855 Back-Check : 883, 884 and 885 Series 880 has adjustable Back-Check function controlled by a separate regulating valve, adjustable after installation. Regular arms are equipped with a 15% (+)(-) 7½% power adjustment bracket. Hold-Open arms are adjustable for holding from 90 to 180. Narrow design permits installation on most modern glass and aluminum doors without adaptors. Series 1800 Grade 1 Factory tested to meet or exceed ANSI Grade 1 Barrier Free operation to comply with Federal Accessibility Standards (ADA) complying with ANSI Narrow design permits installation on most glass and aluminum doors without adapters Standard application for regular arm and Top Jamb installation; optional parallel arm installation (requires optional PA bracket.) Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating valves, adjustable after installation. (Three valves with optional back-check) Slim Plastic Cover or Full Cover (optional) 5 year warranty Attractive baked enamel finishes: AL - Aluminum DU - Storefront Bronze East: Fax:

6 Surface Closers Series 8050, 8900 & 9000 Underwriters Laboratories Inc. Listed Two Speed Control Valves: Closing and Latching speeds controlled by separate regulating valves, fully adjustable after installation. Universal Application: Non-handed for standard, top jamb or parallel arm installation. Rack and pinion mechanism contained in a high tensile precision cast aluminum housing. Stable hydraulic door check fluid for any climatic operation and constant lubrication. Furnished with regular, hold-open or fusible link hold-open arms. Hold-open arms are adjustable for holding from 90 to 180. Attractive Baked Enamel finishes: AL - Aluminum DU - Storefront Bronze Series 8050 Handicap Adjustable Spring Power ADA (Handicap) multi-sized closers with adjustable spring power for a range of sizes adjustable after installation: 8051: 8 ½ lb. opening force to a size : 5 lb. opening force to a size : 5 lb. opening force to a size : 8 ½ lb. opening force to a size 5 CLOSER FUNCTIONS: 8051; Adjustable spring power with adjustable Back-Check controlled by a separate regulating valve, adjustable after installation. 8052; adjustable spring power with adjustable Delayed Closing Action controlled by a separate regulating valve, adjustable after installation & 8054; Basic-adjustable spring power only. Series 8900 Handicap Adjustable Spring Power Surface Mounted - Grade 1 Closer Series 8900 Grade 1 Door Closer (Handicapped approved and UL listed): ADA (Handicap) multi-sized closers with adjustable spring power Adjustable spring power 1 through 6 (adjustable after installation) Two speed control valves allow closing and latching speeds to be controlled by valves Adjustable backcheck Standard sweep and latch speed Standard Tri-packed for regular arm, top Jamb and parallel arm applications Numerous accessories are available to allow for special installation or adaptability 6 West: Fax:

7 Series 9000 Adjustable Spring Power Complies with ANSI A156.4 Grade 1 Barrier Free Operation to comply with Federal AccessibilityStandards (ADA): Complying with ANSI A117.1 ( ) ADA (Handicap) multi-sized closers with adjustable springpower for a range of sizes adjustable after installation. CLOSER FUNCTIONS: Model 9001: adjustable spring power (8-½ lb. Opening Force to Size 5) with adjustable Back-Check controlled by a separate regulating valve. Model 9003: adjustable spring power (5 lb. Opening Force to Size 4) with both adjustable Back-Check and adjustable Delayed Closing Action controlled by separate regulating valves. Furnished with a high impact molded PVC Dress Cover (door closer body casting is finished for use without the Dress Cover). Pedestrian Gate Closers SWINGER 300 Pedestrian Gate Closer Tough, Dependable and Vandal resistant. 2 x 4 x gauge galvanized Steel housing. Gate closer manufactured for pedestrain gates. Two Separate Closing and Latching valves adjustable after installation without removing the closer. Non Handed (right or left swing) Opens to full 105 degrees. Fully adjustable top arm for proper gate alignment. Adjustable zinc plated Bottom Hinge with sealed ball bearings rated for 350 lbs. Designed to close gate into it s latch position without slamming. Adjustable spring power to accommodate various size gates. Adjustable sealed bearing bottom hinge. East: Fax:

8 Hardware DT-1850 Long Throw Deadlock Cylinder backset available: 31/32, 1-1/8 and 1-1/2 Bolt 1-3/8 throw, made of 5 ply laminated steel with a hardened roller pin in a case hardened ply for maximum security. Lock accepts standard 1-5/32 Mortise Key or Thumbturn Cylinders with AR MS-Type cam DH-1820-H Hook Bolt Deadlock Cylinder backset available: 31/32, 1-1/8 and 1-1/2 Bolt 13/16 throw, made of 5 ply laminated steel with a hardened roller pin in a case hardened center ply for maximum security. DT-1850 Lock accepts standard 1-5/32 Mortise Key or Thumbturn Cylinders with AR MS-Type cam DH-1820-S Short Throw Deadlock Cylinder backset available: 1-1/8 Bolt 13/16 throw, made of 5 ply laminated steel with a hardened roller pin in a case hardened center ply for maximum security. Lock accepts standard 1-5/32 Mortise Key or Thumbturn Cylinders with AR MS-Type cam DH-1820-H DH-1820-S DL-4510 Deadlatch Lock Cylinder backset available: 31/32 and 1-1/8 Field reversible for opposite hand Key controlled dogging Latchbolt 1/2 throw, Chrome plate with Delrin insert for smooth, quiet latching Lock accepts standard 1-5/32 Mortise Key or Thumbturn Cylinders with AR MS-Type cam SS Strike included, US 26D CG-4043 Cylinder Guard Hardened steel security ring Free-spinning beveled collar For standard face 5 pin Mortise key cylinder For use on Aluminum Doors Furnished with retaining clip and two spacers Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Anodized Bronze DL-4510 Faceplates 1 x 6-7/8 Flat Radius Radius Weatherstripped Left Hand Beveled Right Hand Beveled 8 West: Fax:

9 DC-2001 (Zinc) Mortise Dummy Cylinder 7/8 Length Cylinder 1-5/32 diameter No Key or cam Cylinder ring 3/16 standard, 5/32 and 7/32 optional Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze RZ-1003 (Zinc) Rim Cylinder 5 pin Cylinder Core face and Key US 26D Schlage C Keyway Low profile Cylinder ring and adaptor plate standard 1-7/8 Break-away screws and 1-1/4 Break-away Spindle standard Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze CZ-1001 (Zinc) Mortise Key Cylinder 1 Length 5 pin Cylinder 1-5/32 diameter AR MS-Type cam Keyway available: Schlage C, Yale 8 Core face and Key US 26D Cylinder ring 3/16 standard, 5/32 and 7/32 optional Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze Removable Core Mortise Key Cylinder Mortise Cylinder Rim Cylinder TZ-3001 (Zinc) Mortise Thumbturn Cylinder 1 Length Cylinder 1-5/32 diameter AR MS-Type cam Thumbturn US 26D Cylinder ring 3/16 standard, 5/32 and 7/32 optional Finishes Available: AL - Anodized Satin Aluminum BK - Anodized Black DU - Anodized Bronze Regular Type Interchangeable Core Type LI-4089 Lock Indicator Set For use with DH-1820 and DT-1850 Type Deadlocks LOCKED in red and OPEN in green letters on white background Includes adhesive backed HS-4089 Header Sign, THIS/THESE DOORS TO REMAIN UNLOCKED WHEN THE BUILDING IS OCCUPIED Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Anodized Bronze East: Fax:

10 PH-4520 Paddle Handle For use with DL-4510 type Latch Lock Push or Pull Paddle Handle Field reversible for opposite hand with PUSH and PULL Plates included Cam Plug, field reversible, included Extruded Aluminum Handle Finishes Available: AL - Handle anodized Satin Aluminum Housing baked Satin Aluminum paint DU - Handle anodized Storefront Bronze Housing baked Storefront Bronze paint HL-4560 Lever Handle For use with DL-4510 type Latch Lock Cam Plug, field reversible, included Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint CP-4560 Cam Plug For use with HL-4560 Lever Handle and PH-4520 Paddle Handle 10 West: Fax:

11

12 SC & SC Strike Sets Use for the new installation of a DL-4510 Type Deadlatch Lock in a Center Hung Door and Frame Non-handed Stainless Steel Strike for Left or Right hand installation Dustbox, back-up plate, and screws included SC for use on 4 door jamb SC for use on 4-1/2 door jamb 15 Series Electric Strike For up to 3/4 latchbolts Choice of failsafe / failsecure Non handed 12 or 24VDC 15-4F12U 4.875, Fail Safe 12VDC 15-4S12U 4.875, Fail Secure 12VDC 15-4F24U 4.875, Fail Secure 24VDC 15-4S24U 4.875, Fail Secure 24VDC SC-4510 Strike Set Use for the new installation of a DL-4510 Type Deadlatch Lock in an Offset Door and Frame Non-handed Stainless Steel Strike for Left or Right hand installation Dustbox, back-up plate, and screws included 25 Series Electric Strike For up to 5/8 latchbolts Field selectable failsafe/failsecure Field selectable 12/24V AC/DC Latch status output Non handed reversible 25-4U 4.875, 12/24VDC 25-6U 6.875, 12/24VDC SC-4510 Strike Set Use for the new installation of a DL-4510 Type Deadlatch Lock in an Offset Door and Frame Non-handed Stainless Steel Strike for Left or Right hand installation Dustbox, back-up plate, and screws included SS-4510 Standard Strike SS-4510 Mounting holes press formed countersink Non-handed Stainless Steel Strike for Left or Right hand installation Electric Bolt Lock Auto relock switch Bolt and door status optional 12/24 VDC operation FS23MIV Dual failsafe, CSFM Listed 1091AIV Failsafe 1291AHV Failsecure Strike Latch Monitoring Kits Provides latchbolt and deadbolt status delayed egress activation, alarm shunt, and mantrap communication Auto relock switch Bolt and door status optional 12/24 VDC operation MS-12 Cylindrical latch status 2-3/4 MS-14 Cylindrical latch status 4-7/8 MS-16 Mortise lock latch status MS-18 Mortise deadbolt status MS-20 Mortise latch & deadbolt status 12 West: Fax:

13 CM CM UniFLEX 45 Series Full Featured Electric Strike For up to ¾ latchbolts Field reversible failsafe/failsecure Field selectable 12/24V AC/DC 1/4 horizontal alignment adj. Latch position status SPDT std. Keeper closed & deadlocked status SPDT std. Low profile 1-3/16 deep 45-A Universal Includes: 4 7/8 square corners 4 7/8 radius corners radius corners 55-ABC 45-4SU 4 7/8 square corners stainless steel 45-4RV 4 7/8 square corners stainless steel 45-6RVU 6 7/8 radius corners 45-7RV 7 15/16 radius corners UniFLEX Universal Strike UniFLEX Application Specific Strike Up to ¾ Latchbolt and 1 Deadbolt Field Reversible, Failsafe/Failsecure 1/8 Horizontal alignment adjustment Dual Voltage 12/24VDC Exceeds 1,000,000 cycles Factory tested 2500 lbs static strength UL 1034 Burglary-Resistant 55-ABC Universal Strike for cylindrical locks, mortise locks without deadbolts and mortise exit devices, including: SDC, Accurate, Arrow, Baldwin, Best, Corbin Russwin, Dorma, Falcon, Hager, Marks, Sargent, Schlage, Yale Warnock Hersey Tested according to: UL 10C, 3 Hr Fire Rated NFPA-252 CAN4-S104 (ULC-S104) 55-A 55-B/C 55-DE 55-F East: Fax:

14 Additional Door Stops are available, see Master Catalog 9000 Series Heavy Duty - Surface Mount For exterior, vestibule and interior single acting doors All stainless steel components - Prefix N Hold-open can be disengaged to act as a stop only Maximum door opening 110,minimum door thickness 1-3/4 Available in all BHMA finishes including US32 & US32D 1000SL Slim Line Heavy Duty - Concealed For exterior, vestibule or interior single or double acting door All stainless steel components Prefix N (Stop Only) 3/4 maximum channel depth Maximum door opening 110o,minimum door thickness 1-3/4 DH-6000 Heavy Duty Kick Down Holder Zinc Alloy Construction Non-Marking Rubber Shoe 7 Body Height Comes with Mounting Screws Finishes Available: AL - Aluminum DU - Storefront Bronze TB-4015 & TB-4016 Threshold Bolt Kit TB-4015: For doors with cylinder height up to 53-1/2. Threaded rod can be cut for cylinder heights lower than 53-1/2 TB-4016: For doors with cylinder height 34 to 37. Bolt 3/8 hexagon hardened steel 11/16 bolt throw Unit complete for attachment to basic Deadlock to provide two-point security HB-4015-N Special Header Bolt Set Standard for 84 Doors with Cylinder Heights of not less than 33 ER-4015-N Extension Rod Kit is available for 8-9 Door Heights 14 West: Fax:

15 HB-4085, HB-4086 & HB-4087 Header Bolt Set HB-4085: For doors 30-1/2 to 50 from Centerline of cylinder to top of door HB-4086: For doors 55-5/8 to 77-1/2 from Centerline of cylinder to top of door HB-4087: For doors 67 to 89 from Centerline of cylinder to top of door Interactive leaf lock when used with basic Long Throw Deadlock in active leaf 5/8 throw expanding bolt Minor adjustments can be made after installation Unit complete with Rod Guide and Header Strike HS-4089 Header Sign For use on transoms and door headers One piece, self-adhesive decal Black letters on aluminum background THIS/THESE DOORS TO REMAIN UNLOCKED WHEN THE BUILDING IS OCCUPIED FB-1200 Flushbolt 15 /16 x 4-1/4 Radius Face Positive U joint actuator with 5/8 throw 1/8, 3/16 and 1/4 offset with 7/8 backset Rod length for 12 Centerline of face installation Square Nylon Tip with beveled corners fits in 1/2 square hole Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint FB-1201: 1/8 offset, without guide FB-1202: 1/8 offset, with guide FB-1203: 1/4 offset, without guide FB-1204: 1/4 offset, with guide FB-1205: 3/16 offset, without guide FB-1206: 3/16 offset, with guide FB-1201-K Flushbolt 15 /16 x 4-1/4 Radius Face Positive U joint actuator with 5/8 throw 1/8 offset with 11/16 backset Square Nylon Tip with beveled corners fits in 1/2 square hole Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint FB-2200 Flushbolt 15 /16 x 4-1/4 Radius Face Positive U joint actuator with 7/8 throw ER-1200 Flushbolt Extension Rod 1/4-20 x 12 Threaded rod Includes coupler 1/8, and 1/4 offset with 7/8 backset Rod length for 12 Centerline of face installation Square Nylon Tip with beveled corners fits in 1/2 square hole Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint FB-2201: 1/8 offset, without guide FB-2202: 1/8 offset, with guide FB-2203: 1/4 offset, without guide FB-2204: 1/4 offset, with guide FG-1200 Standard Flushbolt Guide For use with FB-1200 and FB-2200 Flushbolts FG-1250 Extension Hole Flushbolt Guide For use with FB-1200 and FB-2200 Flushbolts East: Fax:

16 Thresholds Saddle Thresholds IDC413, IDC513 and IDC713 1/4" Available in 36 and 48 lengths Custom sizes and colors available Finishes Available: Aluminum mill finish DKB - Aluminum dark bronze Typical Wall.125 4" IDC413 / IDC413DKB Typical Wall.125 1/4" 5" IDC513 / IDC513DKB Typical Wall.125 7" 1/4" Saddle Thresholds IDC424E, IDC425E and IDC427E Available in 36 and 48 lengths Custom sizes and colors available Finishes Available: Aluminum mill finish DKB - Aluminum dark bronze 4" IDC424E / IDC424EDKB Typical Wall.109 1/2" Typical Wall.109 1/2" 5" IDC425E / IDC425EDKB Typical Wall.109 1/2" 7" IDC427E / IDC427EDKB 16 West: Fax:

17 Door Sweeps Door Sweeps & Brush Seals IDC601 - Nylon Brush Seals Synthetic polymer: Polyamide bristles Excellent abrasion resistance, flexibilty and memory Moisture resistant Retains insecticides well Temperature range -70F to 160F BHMA Certified to ANSI A performance tests for Heat, Cold, Air Leakage and Smoke Control in most common profiles Not effective against water penetration #6 x 3/4 Stainless Steel sheetmetal screws furnished. Screw holes are slotted for adjustment Available colors: Clear with gray brush, Gold with black brush and Dark Bronze with black bush Stock sizes 36 and 48, custom sizes available nylon brush IDC601 1" 7/8" Door Sweeps & Brush Seals IDC97V - Vinyl Sweep Products are UL10B and Can4-S104-80M Classified, complies with NFPA 80 and NFPA 252 for application to Steel fire doors rated up to 3 hrs., and wood type fire doors treated up to 1-1/2 hrs. Positive Pressure UL10C Classified, Category J Complies with IBC UBC7-2 (1997) NFPA 80 & 252 7/8" Smoke & Draft Control Gasketing, Category H Complies with IBC7-2 (1997) Part 2, UL1784, NFPA 105 for use on S labeled Positive pressure Steel fire doors up to 3 hours and wood type fire doors rated up to 1-1/2 hours vinyl Air Filtration Tested to ASTM E283, Standard Test Method for Determining Rate of Air Leakage through Exterior windows, Curtain Walls and Doors 1" #6 x 3/4 stainless steel SMS furnished and Screw holes are slotted for adjustment Available colors: Clear, Gold and dark bronze. Vinyl is standard gray, bronze frame has black vinyl IDC97V Stock sizes 36 and 48, custom sizes available 9/32" IDC673 9/16" 3/4" Door Sweeps & Brush Seals IDC673 - Concealed Fastener Nylon Brush Sweeps Synthetic polymer: Polyamide bristles Excellent abrasion resistance, flexibilty and memory Moisture resistant Retains insecticides well Temperature range -70F to 160F BHMA Certified to ANSI A performance tests for Heat, Cold, Air Leakage and Smoke Control in most common profiles Not effective against water penetration #6 x 3/4 Stainless Steel sheetmetal screws furnished. Screw holes are slotted for adjustment Available colors: Clear with gray brush, Gold with black brush and Dark Bronze with black brush Stock sizes 36 and 48, custom sizes available East: Fax:

18 Offset Pivot Sets 3/4 Offset for use with Aluminum Doors and Frames Oilite bronze bushing in top frame portion Case hardened stud in floor/jamb portion (stainless steel stud in Series 5000 floor/jamb portion) Case hardened, spring loaded pin in top door portion (case hardened fixed pin in Series 5000 top door portion) Full race ball bearing in bottom door portion 1/8 vertical adjustment For doors up to 125 lbs. Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint Series 3000 Series 2000 Series 4000 Series 2000 Offset Pivot Set Series 3000 Offset Pivot Set Series 4000 Offset Pivot Set Series 5000 Offset Pivot Set Series 6000 Offset Pivot Set OP-2700: Flush Door OP-2700: 1/8 Recessed Door OP-3001: Left Flush Door OP-3002: Right Flush Door OP-3101: Left 1/8 Recessed Door OP-3102: Right 1/8 Recessed Door OP-4001: Left Flush Door OP-4002: Right Flush Door OP-5001: Left 1/8 Recessed Door OP-5002: Right 1/8 Recessed Door OP-6001: Left 7/64 Recessed Door OP-6002: Right 7/64 Recessed Door Series 5000 Series West: Fax:

19 OP-7000 Offset Pivot Set (Kawneer Type) A380 Precision die cast aluminum Oilite bronze bushing in top frame portion Full race ball bearing in bottom door portions Door height adjustable by bottom door portion Case hardened stud in floor/jamb portion Includes steel reinforcement plates for the door portions OP-7001 (Left) OP-7002 (Right) OP Non-Handed Offset Pivot Set Non-Handed Offset Top and Bottom Pivot Set For Use With 1-3/4 (44.4 mm) Aluminum Doors Maximum Door Weight is 125 Pounds (57 Kg) 1689 Bottom Pivot 600-PS Floor Mount Floor Mount Bottom Pivot Set for use with 1 deep Bottom Door Rail East: Fax:

20 Intermediate Pivots IP-1900 Intermediate Pivot Set 3/4 Offset for use with Aluminum Doors and Frames Full race ball bearing baked by an oilite bronze bushing in the door portion Case hardened pin in jamb portion fully retractable for ease of installation Easy vertical adjustment Precision Aluminum die cast For doors up to 125 lbs. IP-1901 (Left) IP-1902 (Right) IP-2200 Intermediate Pivot Set IP-1900 Finishes Available: AL - Baked Satin Aluminum Paint BK - Baked Black Paint DU - Baked Storefront Bronze Paint 3/4 Offset for use with Aluminum Doors and Frames Full race ball bearing baked by an oilite bronze bushing in the door portion Case hardened pin in jamb portion fully retractable for ease of installation Easy vertical adjustment Precision Aluminum Extrusion For doors up to 125 lbs. IP-2201 (Left) IP-2202 (Right) Center Hung Pivots Series 400 For use with Aluminum Doors and Frames IP PF Top Pivot Frame Portion 400-PF mounting holes drilled & tapped 400-PF1 mounting holes drilled & countersunk 400-PC Dress Plate Frame Portion For use with 400-PF1 only 400-PD Top Pivot Door Portion 20 West: Fax:

21 Stainless Steel Offset Pivots Pivot sets include top and bottom pivots.offset pivot sets are handed and require an intermediate pivot to accommodate the door weights listed for each set. Door edges must be beveled 1/8 in 2.All sets are available in standard architectural finishes Stainless Steel Offset Pivot 3/4 offset For interior doors up to 4 0 x 8 0 Weight to 300 lbs top pivot included 019 intermediate pivot required Bottom pivot mortised into floor US32D models UL listed for use on 3 hour fire doors Extended spindles available BHMA/ANSI C07162/3530A (modified) 0147 Stainless Steel Offset Pivot 3/4 offset For interior doors up to 4 0 x8 6 For exterior doors up to 3 6 x 7 0 Weight to 600 lbs top pivot included 019 intermediate pivot required Bottom pivot mounted to floor US32D models UL listed for use on 3 hour fire doors BHMA/ANSI C07162/3530A (modified) Extended spindles available Stainless Steel Intermediate Pivots Intermediate pivots are used to keep doors in alignment. All intermediate pivots are offset hung and cannot be used on center hung doors. Per NFPA 80, fire doors are to have an intermediate pivot for additional 30 or fraction thereof for door heights over 6. Available in most architectural finishes. 019 Stainless Steel Intermediate Pivot 3/4 offset,handed Full mortise Needle bearing supplied standard. Can be used on heavy duty doors US32D models UL listed for use on labeled doors BHMA/ANSI C07321/ E019 Stainless Steel Power Transfer Offset Pivot 3/4 offset,handed Full Mortise Can be used on heavy duty doors US32D models UL listed for use on labeled door (8) 28ga. wires supplied standard* Door and jamb portions are factory assembled *Pivot cannot be separated for installation E019 East: Fax:

22 Continuous Hinges IDC Continuous Gear Hinges are all heavy duty. All hinges have double the number of bearings of standard duty hinges and are pinless. There are no accessible screws, bolts or pins when the door is closed. IDC gear hinges are surface applied to the frame and door. No machining is required. Whether surface mount or concealed, the IDC continuous gear hinges eliminate the gap between the door and frame, and provide a weatherproof, tamper-proof barrier. The IDC gear hinges templated and the hole pattern is the same from hinge to hinge. IDCA110 Concealed UL listed for all Models (except 130) for the following rated doors: Swing Type Metal and Wood Doors up to 1 hour without Fire Studs Swing Type Wood Doors up to 1-1/2 hour with Fire Studs Swing Type Metal Doors up to 1-1/2 hour without Fire Studs Swing Type Metal Doors up to 3 hours with Fire Studs IDCA210HD Full Surface Swing Clear Size: 83, 85, 95 and 120 are standard Other sizes available Stainless Steel Continuous Hinges IDCA570 Full Surface For Narrow Frames IDCA571HD Full Surface IDC Stainless Steel Hinges are made of 304 Stainless Steel. Continuous Stainless Steel Hinges run the entire length of the door eliminating any gaps between the door and the frame, providing high security and also distributing the weight of the door evenly through the opening. Continous Stainless Steel Hinges are ideal for highly abusive & corrosive applications such as hospitals, water treatment plants, swimming pools, and salt spray applications are utilized. Heavy-Duty 14 Gauge 304 Stainless Steel. US32D Satin Stainless Steel Self drilling screws Supports door weights up to 600 lbs. 4-0 Maximum door width Nominal Sizes 7, 8 & 10 are Non-handed 6 8 & 7 2 are handed hinges 1/4 diameter stainless steel pin UL fire rated: Hollow Metal doors - 3 Hours Hollow Metal & Composite wood fire - 90 Min Wood doors - 20 Min IDCA500 Full Concealed Edge Mount No exposed Fasteners when door is closed Electrical modifications available IDCA502 Full Surface Flush Mount IDCA503 Half Surface Decorative Fastener Cover Templated Current transfer prep available IDCA500 Full Concealed Edge Mount IDCA503 Half Surface IDCA502 Full Surface Flush Mount 22 West: Fax:

23 IDCA504 Surface Mounted Decorative Fastener Cover Templated Current transfer prep available (door leaf only) IDCA505 Full Concealed Edge Guard No exposed Fasteners when closed Adjustable to accommodate variances in door thickness Templated Electrical modifications available Wrap around guard protects from unslightly gouges and dents and also protects from further damage. Load of the door is distributed along the entire length of jamb. Square Edge Hinge side door only IDCA506 Surface Mounted Decorative Fastener Cover Templated Current transfer prep available (door leaf only) IDCA504 Surface Mounted IDCA505 Full Concealed Edge Guard IDCA511 Full Concealed Swing Clear With Edge Guard No exposed Fasteners when door is closed Templated IDCA506 Half Surface With Edge Guard IDCA515 Full Concealed With Edge Guard No exposed Fasteners when door is closed Templated Electrical modifications available IDCA515 Full Concealed With Edge Guard Stainless Steel Edge Guards Heavy-Duty 16 Gauge 304 Stainless Steel. US32D Satin Stainless Steel No exposed Fasteners when door is closed Self drilling screws Nominal sizes 6 8, 7, 7 2, 8 & 10 Symmetrically templated, Non Handed Hardware cut-outs available IDCA511 Full Concealed Swing Clear With Edge Guard Specify when ordering: Square edge door or Beveled edge door IDCA528 Edge Guard with 1 Lip Only IDCA538C Full Edge Guard IDCA548T Full Edge Guard With Astragal East: Fax:

24 Butt Hinges IDCAHP Series 5 Knuckle 2 Bearing IDCAHA Series 5 Knuckle 2 Bearing IDCAH SPR Series Spring Hinge IDCAHP 4545 BB - NRP IDCAHP 4545 PB - NRP Size: 4.0 x x x x5.0 Other specs are available. Please contact us! Finishes Available: US3, US4, US10, US10B, US26, US26D, US32, US32D, White, etc. Options: NRP (Non-Removable Pin) Power Transfers IDCAHA 4545 PB IDCAH SPB 4545 Spring Hinge Power Transfer Hinge UL 10B listed for 3 hr fire doors 4 foot cable (standard) Optional DPS PTH-4Q 4 wires, 1 Amp PTH-2-4Q 6 wires, 1 pair - 16 Amp inrush, 2 Amp continuous, 2 pair - 1 Amp PTH-10Q 10 Wires, 1 Amp DPS Door status contact, optional PTH Electric Power Transfer Device IDC s heavy duty Electric Power Transfer Device provides a concealed and secure means of transferring electric lock and exit device power and signal wires from the frame to the door. Completely concealed when the door is closed the PTM Electric Power Transfer Device is ideal for heavy traffic and applications requiring higher security to inhibit tampering and abuse. PTD 24 West: Fax:

25 Mechanical Exit Devices 8000 Series Exit Device Grade 1 Panic and Fire Rated IDC 8000 Series Exit Devices are heavy duty and designed for heavy traffic applications. The devices are Underwriters Laboratory (UL, USA and ULC, Canada) listed for PanicExit Hardware or Fire Exit Hardware, and are certified to ANSI A Grade 1. Rim Mount Exit Device All devices are non-handed design Slight pressure on device touch bar will retract latch(s) for immediate exit Auxiliary guarded latch deadlocks latch bolt automatically when door is closed Mortise Exit Device High shock-resistant latching mechanical design for protection from vandalism All inside components are made of high rust-resistant alloy or heavily electroplated steel Anti-fading, electroplated or architectual base material finishes on all exposed surfaces are available With a dogging mechanism, users have a choice of hex-key or cylinder operated for positive push-pull action at peak traffic time. This dogging device will also help by increasing the life of the exit device (panic label only). Surface Vertical Rod Exit Device Available in Wide or Narrow Stiles, Surface Vertical Rod (SVR), Concealed Vertical Rod (CVR) Less Bottom Rod (LBR) and Rim or Mortise locks Concealed Vertical Rod Exit Device Escutcheon Trim Series 8000 Trim has 4 through-bolts to the device chassis directly for better security and durability. It fits 1-3/4 (44) door standard. For 2 (51mm), 2-1/4 (57mm) thick door or the shim-mounted exit device, specify the door thickness when ordering. Clutch freewheeling design. The lever rotates when the door is locked, preventing excessive force from being applied to the horizontal lever. Operation Options Key Locks & Unlocks Lever Lever Always Active (No Cylinder) KeyRetracts Latchbolt (Rigid Lever) Pull When Dogged (Rigid Lever) Functions Classroom Passage Storeroom Dummy Trim Designation Model Number & Application Cylinder Escutcheon Lever 89L01A Blank Escutcheon Lever 89L01B Night Latch Escutcheon Lever 89L01C For Rim, Surface / Concealed Vertical Rod, LBR Exit Devices Use Dummy Escutcheon Lever 89L01D 89E01A 89E01B 89E01C 89E01D Electrical Trim Field reversible fail safe / fail secure Audible tone when energized 4 ft cable and connectors 600/300 12/24VDC For Mortise Lock Exit Devices Use Only East: Fax:

26 Electrified Exit Device 1 Amp Electric Latch Retraction Rim Mount, Vertical Rod & Mortise E Electric Latch Retraction For 6100, 6200, 6300, 6800 Example: S6101F-RR-36-U-E Operation: Momentary or maintained latch bolt and push pad retraction Voltage: 1 Amp activation, 180 ma continuous EMC: Sequencer Module required for pair of doors and automatic doors. 12/24VDC. Installed in power supply Monitoring: See S6000 Spectra datasheet for details 602RF 1 Amp power supply (1 EMC max) 632RF 2 Amp power supply (2 EMC max) Electrified Mortise Exit Device Mortise M Electric Mortise Exit Device Example: S6303F-LR-U-36-M x GK03U Field reversible fail secure / fail safe. Remains latched when unlocked for fire door integrity Failsafe (F) fire rated device for stairwell doors Power loss or signal from fire command center releases fail safe device immediately Voltage: 1600/300 12/24VDC Monitoring: See S6000 Spectra datasheet for details Electrified Dogging Rim Mount, Vertical Rod & Mortise G Electric Dogging (failsecure) 6100, 6200, 6300, 6800 Example: S6103P-LR-U-36-G x SP03U When energized by optional built-in or remote switch manual, depressing the pushpad, causes the pushpad and latch to remain retracted (unlocked) providing push-pull door operation. When de-enegrized or signaled by a fire alarm, the pushpad and latch are released. Voltage: 170/100 12/24VDC Monitoring: See S6000 Spectra datasheet for details IDC LR100 Series Latch Retraction - For 8000 Series Exit Device Simultaneous Latch Retraction & Dogging Field Retrofit UL Listed When IDC Factory Installed Quiet Motor Operation 450 ma Inrush, 180 ma Continuous Compatible other Manufactures Exit Devices Von Duprin 98/99 Series, 33/32 Series, 22 Series and other manufacture devices 26 West: Fax:

27 Exit Alarm Rim Mount, Vertical Rod & Mortise A Exit Alarm, 9V battery powered B Exit Alarm, 12-24V AC/DC input, 9V battery backup For 6100, 6200, 6300, 6800 Example: S6801P-LR-U-36-A 100 db alarm; visual and audible On/Off status: Armed - green LED blinks every 4 seconds, Alarm mode - red LED, Bypass - no LED Remote status output 15 or 60 second arming delay 2 modes: Continuous alarm with manual key reset; Automatic re-arm 2 minutes after door closes with any manual key reset before 2 minutes. Options: 6, 10 & 20 minutes alarm; 1 or 5 second re-arm delay Remote access control, arm, disarm inputs REX and latch status outputs Delayed Egress DE Wall mount delayed egress controller with keypad and electrified exit device, 6100, 6200, 6300, 6800 Example: S6101F-R-U-36-DE x GK03U KDE Keypad controller with redundant key switch capable of all keypad control features 602RF 1 Amp power supply User PIN codes may be assigned to 1, 2 or all control functions. Reset, sustained bypass and momentary bypass (RES). Audible alarm voice release time, warning or safety message Visual display countdown, locked/unlocked, egress executed 15 or 30 second exit delay, 1 or 2 second nuisance delay Monitoring: See S6000 Spectra datasheet for details Electric Frame Actuator Hitower Pro Frame Actuator Controlled Fire Exit Device Features include failsafe operation and unlocks by access control, power loss or signal from fire command center. Door stays latched even when unlocked. All wiring is maintained in the strike jamb. Complies with national building and fire codes Specify Voltage: 24VDC, 24VAC, 115VAC Monitoring: See S6000 Spectra datasheet for details No wiring through door No door transfer hinge 500 Series Exit Device REX Switches 27 SPDT & DPDT 5 Amp switch kits Retrofit mechanical exit devices Request-to-Exit & alarm shunt Delayed egress activation Magnetic lock release Switch kits available for Von Duprin, Yale, Sargent, Adams Rite, Arrow, Cal Royal, Corbin, Dor-O-Matic, Jackson, Kawneer, Monarch, Precision East: Fax:

28 Mechanical Exit Devices 5000 Series Exit Device Panic and Fire Rated International Door Closers IDC 5000 Series Exit Devices meet the Life and Fire Safety Codes as prescribed by UL and ANSI / BHMA standards. These durable devices are designed for both standard and commercial applications. The 5000 Series were tested and approved by Underwriters Laboratories (UL, USA and ULC, Canada) and listed to comply with UL 10C, and Uniform Building Code Standard 7-2, Fire Test of Door Assemblies (1997). All devices are non-handed design Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed High shock-resistant latching mechanical design or protection from vandalism Narrow Design Panic SVR Exit Device All inside components are made of high rust-resistant alloy or heavy electroplated steel Baked powder coating, electroplated or architectual base finishes are used on all exposed surfaces Outside trims are provided by rose and escutcheon lever or knob in a varity of styles All trim features a through-bolted design to the devices that allow easy installation but not to comprise on security With a dogging mechanism, users have a choice of hex-key or cylinder operated design for a positive push-pull door action during peak traffic time Available in Wide or Narrow Stiles, Surface Vertical Rod (SVR), Concealed Vertical Rod (CVR), Rim and Mortise Locks Mortise Cylinder Rim Cylinder Series Regular Type 426 Trim has two through-bolts to the device chassis directly for more security and durability. It fits 1-3/4 (44) door standard. For 2 (51mm), 2-1/4 (57mm) thick door or the shim-mounted exit device, specify the door thickness when ordering This series trim is Anti-Vandalism design that can prevent the lock from damaging Interchangeable Core Type when key locks the lever in rigid and horizontal position. Operation Options Key Locks & Unlocks Lever Lever Always Active (No Cylinder) KeyRetracts Latchbolt (Rigid Lever) Pull When Dogged (Rigid Lever) Functions Classroom Passage Storeroom Dummy Trim Designation Cylinder Escutcheon Lever Blank Escutcheon Lever Night Latch Escutcheon Lever Dummy Escutcheon Lever Model Number & Application 58L01A 58L01B 58L01C For Rim, 5510 Series Rim, 5530 Series Surface Vertical Rod 58L01D 28 West: Fax:

29 Series 7100 Concealed Vertical Rod Underwriters Laboratories Inc. Listed - Panic Hardware For use with narrow, medium and wide stile Aluminum doors Non-handed, Field Reversible for LHRB or RHRB doors Outside Unlatching and Dogging by Cylinder Key or Dogging by Hex Key in Touch Bar Top Steel Toggle Latch and Bottom Steel Rod Latch Bolt Units use Standard Mortise Cylinder with MS Type Cam and MP-6182 Cylinder Mounting Pad Standard Units for 36 and 48 door widths (cut bar to fit) and up to 84 in height Can be used on 30 wide doors Finishes Available: AL - ALUMINUM - Anodized extruded Aluminum with Baked Aluminum Painted Cover Caps DU - STOREFRONT BRONZE - Bronze Anodized extruded Aluminum with Baked Storefront Bronze Painted Cover Caps MP-6000 Mounting Plate for Wood or Metal Doors PH-6000 Pull Handle MP-6182 Cylinder Mounting Pad with Lock Ring CZ-1001 Mortise Cylinder Series 7300 Rim Panic Underwriters Laboratories Inc. Listed - Panic Hardware For use with narrow, medium and wide stile Aluminum doors, Hollow Metal or Wood Doors Non-handed, for LHRB or RHRB doors Latch Bolt throw 5/8 Dogging by Hex Key in Touch Bar Outside Unlatching with standard Rim Cylinder Standard Units for 36 and 48 door widths (cut bar to fit) Can be used on 30 wide doors RZ-1003 Rim Cylinder Finishes Available: AL - ALUMINUM - Anodized extruded Aluminum with Baked Aluminum Painted Cover Caps DU - STOREFRONT BRONZE - Bronze Anodized extruded Aluminum with Baked Storefront Bronze Painted Cover Caps ST-6312 Standard Surface Roller Strike East: Fax:

30 Mechanical Locksets Grade 1 Cylindrical Locks IDC ALS Series locksets are designed for commercial, industrial and institutional use, where dependable operation and longevity is required along with high resistance to vandalism and abuse. Applications include office buildings, government centers, factories, schools and hospitals and more. Internal clutch provides vandal resistance by permitting lever rotation without retracting latch when locked. Independent heavy duty springs provide effective lever return and support. R-Lever Standard Mechanical - ANSI GRADE 1 Cylindrical Locksets ANSI/BHMA Grade 1 ANSI A compliant Internal clutch for vandal resistance 2-3/4 backset 4 7/8 strike standard 2 3/4 strike optional Dull chrome finish standard R-Lever, I-Core Standard, I-Core Functions Function Ordering Example: ALS10LF Passage ALS10 x ALS20LF Privacy LF - L Type w/flat Rose ALS30LF Entrance RF- R Type with/flate Rose ALS40LF Classroom LR- L Type with/round Rose ALS50LF Store room RR- R Type with/round Rose NOTE: Dull chrome finish standard ALS10 Standard ALP Series Grade 2 Cylindrical Locksets Available ALS10 R-Lever 30 West: Fax:

31 Electrified Locksets Electra Pro Electrified Cylindrical Locksets Request to Exit output standard ANSI Grade 1 Dual 12/24 VDC Failsafe or failsecure operating mode Clutch for vandal resistance Optional I-Core IDC cylinder with C keyway ADA compliant lever handles UL Listed for 3Hr fire rated doors Eclipse or Galaxy lever Functions Z7250 Failsafe, locked outside Z7252 Failsecure, locked outside UL CSFM MEA Electra Mod Electrified Cylindrical Locksets Locked on exterior only IDC electrified Schlage ND series 12/24VDC Rex optional Customer or distributor send Schlage lock to IDC for modification Functions S7250 Failsafe S7252 Failsecure Options R Request-to-exit, SPDT UL CSFM MEA East: Fax:

32 Mortise Locksets Grade 1 IDC Heavy Duty Mortise Locks comply with American National Standard Institute requirement ANSI/ BHMA Grade 1. All our locks are field reversible and require only simple steps for changing the hand of lock for easy installation. Field reversible handing without disassembly Retrofit most other brand locksets (consult factory) Internal clutch for vandal resistance One or two heavy duty spring cages as required per function Functions Standard R-Lever Dull chrome finish standard M7801EU M7801GU Passage M7804EU M7804GU Office M7805EU M7805GU Classroom M7807EU M7807GU Store room M7809EU M7809GU Apartment entrance / vestibule M7813EU M7813GU Corridor / exit M7820EU M7820GU Entrance M7822EU M7822GU Privacy Standard R-Lever L Lever with Round Rose Key Cylinder - Optional R Lever with Flat Rose Mortise Locks with Escutcheon Trim Available DG Pro Electrified Mortise Locksets Drilling guide spans full door width for more accurate drilling Full width guide is adjustable several degrees up or down from hinge stile to lock stile to accommodate lock position. Functions 7000-DG Door Core Drill Fixture with case 7000-DB1/4 1/4 4 Ft. Drill Bit 7000-DB3/8 3/8 4 Ft. Drill Bit 32 West: Fax:

33 Mortise Locksets Selectric Pro Electrified Mortise Locksets IDC quality standards ANSI Grade 1 Heavy Duty Replaces most lock brands Field selectable Failsafe or Failsecure Field selectable function: locked outside only or both sides Field selectable 12/24VDC Field selectable handing Select factory supplied IDC trim or Schlage trim provided by others UL Listed for 3Hr fire rated doors Functions Z7830 Failsafe, locked both sides Z7832 Failsecure, locked both sides Z7850 Failsafe, locked outside Z7852 Failsecure, locked outside Z7835 Locked outside and/or inside Outside failsecure, inside failsafe Schlage Best Options R Failsafe, locked both sides D Failsecure, locked both sides S Failsafe, locked outside Sargent UL CSFM MEA Dorma Corbin Russwin Selectric Mod Mortise Lock Electrification Electrification of Major Brands: Send the mechanical lock to IDC, and IDC will return the electrified lockset to the customer. To expedite delivery, IDC stocks major brands for electrification. Customer may then send mechanical locks to IDC for credit and replenishment of IDC stock. Arrow Marks Yale Field selectable 12/24VDC UL Listed for 3 hr fire rated doors Functions 7830 Failsafe, locked both sides 7832 Failsecure, locked both sides 7850 Failsafe, locked outside 7852 Failsecure, locked outside Cal Royal Options* R Request-to-exit, SPDT D Door Status, SPDT S Latched and Locked, SPDT L Latchbolt Status, SPDT *not available with all brands Falcon PDQ UL CSFM MEA East: Fax:

34 1511V & 1512V 1650lbs. Holding Force Field Upgrade & Service Without Removing From The Frame ANSI Grade 1 BHMA Certified Holding Force 12/24VDC Sensing Input 350mA@24VDC (single) 700mA@12VDC (single) 1511V (Single) 1512V (Double) UL10C CSFM MEA UBC 1571V & 1572V Energy Saver 1200lbs. Holding Force ANSI Grade 1 BHMA Certified Holding Force 12/24VDC Sensing Input 125mA@24VDC (single) 250mA@12VDC (single) Lower Power Consumption 1571V (Single) 1572V (Double) UL10C CSFM MEA UBC Single 1511V, 1571V & V & 1582V 650lbs. Holding Force ANSI Grade 1 BHMA Certified Holding Force 12/24VDC Sensing Input 220mA@24VDC (single) 440mA@12VDC (single) 1581V (Single) 1582V (Double) UL10C CSFM MEA UBC Double 1512V, 1572V & 1582 E6200 Full Featured Magnetic Lock 1200 lb holding force Retrofits Securitron and Locknetics 70 magnetic locks Magnetic bond sensor standard Door status standard 10ft (3.05m) jacketed, stranded conductor cable Dual voltage 12/24VDC Steel housing, US32/630 E-6200 Full Featured Magnetic Lock 34 West: Fax:

35 Interlocking Quick Mount Assembly Monitoring and Timer Options D - Door position sensor B - Magnetic bond sensor T - Adjustable 1-30 sec. timer L - Bi-Color LED A - Anti-Tamper sensor Multiple option example Examples 1511VD 1511VB 1511VT 1511VL 1511VA 1511VDBT See modular program pricing when ordering separately for field upgrades. Different part numbers and pricing may apply Universal Top Jamb Kits TJ1V for 1511 and 1571 TJ2V for 1512 and 1572 TJ81V for 1581V TJ82V for 1582V Universal Glass Door Kits Compatible with all lock models Field adjustable for.5,.625 and.75 glass doors HDB1 For 1511, 1571, 1581 HDB2 For 1512, 1572, 1582 Hi/Shear EMLock 2000lbs. Holding Force Static sensor activates lock only when door is aligned and at rest Lateral & vertical alignment adj. Sensing 12/24VDC input Status sensors optional 1561-ITCM top channels 561-HTCM Up to top channels 1561-FTCM Mortise armature prep UL10C CSFM MEA UBC Hi/Shear EMLock East: Fax:

36 Mini Exit Check Delayed Egress 650lbs. Holding Force 15 sec exit delay, 1 sec nuisance delay Subdued alarm, two tones UBC, NFPA 101 NFPA 1. UFC, IBC, IFC, BOCA & Chicago code compliant Field selectable manual or auto power-up modes 1581SNDV NFPA compliant 1581SBDV BOCA, Chicago compliant Exit Check Delayed Egress Lock 1650lbs. Holding Force Activated by door movement or sense bar 15 sec. unlock delay, 1 or 2 sec. nuisance delay Emergency release input Mode status outputs Dual 12/24VDC operation NFPA, UBC, IBC, IFC, CBC compliant BOCA & Chicago compliant optional Digital countdown display Selectable voice or tone warning 1511SNAKV Single 1511TNAKV Tandem 101-DE Exit Check Delayed Egress Controller 15 or 30 second exit delay Built-In 3 function keypadcontrol Inputs Built-in annunciation Monitoring outputs Optional EMLock outputs Choice of mounting Trigger modes Power-up modes Display modes 101-DE Wall mount controller with keypad control and reset Specify Lock: 1581DEV, 1571DEV, 1511DEV, 1575DEU, 1576DEU Exit Switches Illuminated green PUSH TO EXIT sign Momentary switch button SPDT contact Stainless steel finish 422U 1 Gang, 2 button 423U 1 Gang, 1-60 sec timer, 2 button 412NU Narrow, 1¾ button Mechanical Switch Bar SPDT Contact (2 contacts opt.) Power loop included Epoxy kit optional for all glass door 42 & 48 optional Push To Exit sign included Code compliant sign MSB550V Aluminum MSB550Y Black Anodized 500-GL Glass door kit & adhesive UL CSFM Emergency Pull Station Blue housing with easy to read activation instructions avoids confusion with red fire alarm stations. 2-SPDT 10 Amp Contacts; 1-SPDT for lock release and 1-SPDT auxiliary contact for remote monitoring, CCTV activation or alarm activation. 492 Pull station emergency door release 492GL4 Four replacement glass rods 492BB Blue surface mount box Sure Exit Sense Bar Sensor technology Tri-failsafe, auto activated emergency release Two SPDT outputs 12/24VDC operation Special finishes and lengths available Push To Exit sign included PSB560V 36 Aluminum PSB560Y 36 Black Anodized 500-GL Glass door kit & adhesive UL CSFM 36 West: Fax:

37 Proximity & Pin Access Control System Key programmable for Standalone applications EntryCheck Access Control System PC Managed Network Up To 99 Openings E5P Single Door Prox & PIN Reader & Controller 2nd reader input for egress or outdoor use E5C Single Door 2 Reader Controller Only Choice of 6 prox and keypad readers HID compatible cards & readers by others: 125 KHz; 26 to 40 bit Up to 3000 users E5P 4 read range Prox card only, Prox & PIN or PIN only entry Scheduled events and holidays Guard patrol function Audit trail, 3500 transaction buffer HID ProxCard II, 10 cards HID ProxCard II, 25 cards HID ProxKey II, 10 key fobs HID ProxKey II, 20 key fobs Optional Readers: Standalone Access Control E4KP EntryCheck Proximity & Access Control Reader HID compatible cards by others: 125 KHz; 26 to 40 bit Up to 650 card users Up to 3 read range Weather resistant Remote relay module Prox only or Prox and PIN entry Forced entry alarm Duress output Cost-effective solution for access control and management User card can be registered/deleted in single or batch mode (with consecutive numbers) 6005B E5PW K30W K40W 917W HID ProxCard II, 10 cards HID ProxCard II, 25 cards HID ProxKey II, 10 key fobs HID ProxKey II, 20 key fobs EntryCheck Digital Keypad Request-to-Exit input 2 Form C relay contacts 480 PIN codes from 1-6 digits Two LED status indicators Door sense input Disable keypad Anti-tamper keypad lockout 928U Stainless Steel EntryCheck Digital Keypad Request-to-Exit input 1 main relay output 150 PIN codes from 1-6 digits Red/Green/Amber status indicators Panic Code Disable keypad Anti-tamper keypad lockout 12/24VAC/DC 917U Stainless Steel TR12 Plug-in 12VDC Power Supply East: Fax:

38 4 Station Door Control Relay Module Programmable Door Controller 7 field selectable modes: standard relay, timer, latch, or latch plus timer and 3 mantraps modes. UR2A 2 Station Controller 4 inputs, 2 fused outputs 2 aux inputs, 2 aux outputs UR4A 4 Station Controller 8 inputs, 4 fused outputs 4 aux inputs, 4 aux outputs Power Supply Capacity 631/632RFA- 1 max. 634/636RF - 2 max 12/24 VDC voltage input 4 N.O. inputs 4 fused SPDT wet or dry outputs 4 non-fused SPDT auxiliary outputs Dim: 6 x 3 CR4 Control Module Power Supply Capacity 631RFA 2 max 634RF 4 max 636RF 4 max 1 Amp Class 2 Access Control Power Supply 12/24VDC field selectable Emergency release input with manual reset capability 1 Power limited switched output 1 Power limited auxiliary output Battery charger Input, output & battery status LED 621B Power supply module 621P Power supply module, plug-in transformer 621PJ Power supply module, plug-in transformer & small enclosure 1 Amp Class 2 UL 294 Access Control Power Supply 12/24VDC field selectable Emergency release input Low battery disconnect Input, output & battery status 2 timers or door control modules with fused outputs (optional) 602RF 1 Amp Power Supply FB4 4 optional fused outputs Specify up to (2) FB4 for (8) outputs 38 West: Fax:

39 1.5 Amp Class 2 UL 294 Access Control Power Supply 12/24VDC field selectable Emergency release input Low battery disconnect Input, output & battery status 2 timers or door control modules with fused outputs (optional) 631RF 1.5 Amp power supply FB4 4 optional fused outputs 2 Amp Class 2 Access Control Power Supply 12/24VDC field selectable Low battery disconnect Input, output & battery status Emergency release input with manual reset capability 2 timers or door control modules with fused outputs (optional) 632RF 2 Amp power supply FB4 4 optional fused outputs 4 Amp Class 2 Access Control Power Supply (1) 4A output & (2) 2A outputs Field selectable 12/24VDC Emergency release input with field selectable manual reset Low battery disconnect Input, output & battery status Large cabinet: 16 Wx14 Hx6 D 634RF 4 Amp Power Supply FB4 4 optional fused outputs Specify up to (4) FB4 for (16) outputs 6 Amp Class 2 Access Control Power Supply (1) 6A output & (3) 2A outputs Field selectable 12/24VDC Emergency release input with field selectable manual reset Low battery disconnect Input, output & battery status Large cabinet: 16 Wx14 Hx6 D 636RF 6 Amp Power Supply FB4 4 optional fused outputs Specify up to (6) FB4 for (24) outputs East: Fax:

40 Proud of our Past Focused on the Future OHC Closers Surface Closers Gate Closer Door Hardware Miscellaneous Hardware Strikes Door Holders, Stops & Flush Bolts Thresholds Door Sweeps Aluminum Steel Pivots Stainless Steel Pivots Aluminum Geared Hinges Stainless Steel Pin & Barrel Hinges Butt Hinges & Power Transfers Mechanical - Electrified Exit Devices & Escutcheon Trim Mechanical - Locksets Mechanical - Electrified Mortise Locksets Electro-Magnetic Locks Access Controls WEST: 4431 E. La Palma, Anaheim, CA Tel: (714) (800) Fax: (714) west@intldoorclosers.com EAST: 1920 Air Lane Drive, Nashville, TN Tel: (615) (800) Fax: (615) east@intldoorclosers.com

Spectra Class. N6000 Series Exit Devices SECURITY DOOR CONTROLS. N6100 Rim Mount Exit Device. N6200 Surface Vertical Rod Exit Device.

Spectra Class. N6000 Series Exit Devices SECURITY DOOR CONTROLS. N6100 Rim Mount Exit Device. N6200 Surface Vertical Rod Exit Device. N6000 Series Exit Devices Spectra Class Rim Mount Surface Vertical Rod N6100 Rim Mount Exit Device For use on single doors or pair of doors with mullion 1-3/4"(44 mm) door thickness standard. Specify thickness

More information

Spectra Class - Specification Grade Exit Devices for superior Architectural Style & Performance

Spectra Class - Specification Grade Exit Devices for superior Architectural Style & Performance S6000 & N6000 Spectra Exit Devices Spectra Class - Specification Grade Exit Devices for superior Architectural Style & Performance The new mechanical SDC S6000 & N6000 Spectra series panic and fire rated

More information

International Hardwarecorp.

International Hardwarecorp. Volume 15 HARDWARE SECURITY STOREFRONT GATES International Hardwarecorp. Since 1968 ACCESS CONTROL PARKING OVERHEAD CONCEALED CLOSERS 200 & 200-SA Series 5 YEAR WARRANTY Underwriters Laboratories Inc.

More information

ARCHITECTURAL DOOR HARDWARE DOOR STOPS & HOLDERS THRESHOLDS & GASKETING CATALOG

ARCHITECTURAL DOOR HARDWARE DOOR STOPS & HOLDERS THRESHOLDS & GASKETING CATALOG ARCHITECTURAL DOOR HARDWARE DOOR STOPS & HOLDERS THRESHOLDS & GASKETING CATALOG January 1, 2017 v3 West Coast Office (800) 544-4422 East Coast Office (800) 225-6737 intldoorclosers.com Index DOOR STOPS

More information

ARCHITECTURAL DOOR HARDWARE EXIT DEVICE CATALOG

ARCHITECTURAL DOOR HARDWARE EXIT DEVICE CATALOG ARCHITECTURAL DOOR HARDWARE EXIT DEVICE CATALOG January 1, 2017 v3 West Coast Office (800) 544-4422 East Coast Office (800) 225-6737 intldoorclosers.com Index EXIT DEVICES 5000 Series (Grade 2)...1-10

More information

SPECTRA S6000 TOUCH BAR EXIT DEVICES Discount Code XK

SPECTRA S6000 TOUCH BAR EXIT DEVICES Discount Code XK SPECTRA S6000 TOUCH BAR EXIT DEVICES Panic & Fire Rated ANSI / BHMA Grade 1 SDC S6000 Spectra series panic and fire rated exit devices are available in rim mount, mortise and surface vertical rod configurations.

More information

GRADE 1 ELECTRIFIED CYLINDRICAL & UNIT LOCKS

GRADE 1 ELECTRIFIED CYLINDRICAL & UNIT LOCKS GRADE ELECTRIFIED CYLINDRICAL & UNIT LOCKS LAK Function: Specifications: Features: Locked on the outside only. The 00mA @ VDC Vandal resistant clutch lever release inside lever is always unlocked for 9/6

More information

SPECTRA S6000 Touch Bar Exit Devices - RIM and SURFACE VERTICAL

SPECTRA S6000 Touch Bar Exit Devices - RIM and SURFACE VERTICAL SPECTRA S6000 Touch Bar - RIM and SURFACE VERTICAL Panic & Fire Rated ANSI / BHMA Grade 1 SDC S6000 Spectra Series panic and fire rated exit devices are available in rim mount, mortise and surface vertical

More information

5/8" Radius Corner Hinges

5/8 Radius Corner Hinges 5/8" Radius Corner Hinges FULL MORTISE 5 Knuckles Removable Pin Steel with Steel Pin Non-Template Pack with Phillips flat-head screws (machine and wood) H44-50R SPRING HINGE UL Listed Steel with Steel

More information

S6000 Spectra Exit Devices

S6000 Spectra Exit Devices S6000 Spectra Exit Devices SPECTRA CLASS - SPECIFICATION GRADE EXIT DEVICES FOR SUPERIOR ARCHITECTURAL STYLE & PERFORMANCE The new mechanical SDC S6000 Spectra Series panic and fire rated exit devices

More information

20 Series. Exit Device

20 Series. Exit Device 20 Series Exit Device Copyright 2003, 2007, 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents Table Of Contents Page Features, Applications and UL

More information

Table Of Contents. 30 Series Exit Device. On The Cover

Table Of Contents. 30 Series Exit Device. On The Cover 30 Series Exit Device Copyright 1999, 2001, 2004, 2008, 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table Of Contents Page Features, Applications and UL Fire

More information

Table of Contents 20 Series Exit Device

Table of Contents 20 Series Exit Device 20 Series Exit Device Copyright 2003, 2007, 2009-2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents Features, Applications and UL Fire Door Ratings...

More information

CAL-ROYAL & F2200 Rim Type Panic And Fire Exit Devices 2260 & F2260 Vertical Rod Panic And Fire Exit Devices ANSI A156.

CAL-ROYAL & F2200 Rim Type Panic And Fire Exit Devices 2260 & F2260 Vertical Rod Panic And Fire Exit Devices ANSI A156. CAL-ROYAL P R O D U C T S, I N C. 3 HOUR FIRE RATED 2200 & F2200 Rim Type Panic And Fire Exit Devices 2260 & F2260 Vertical Rod Panic And Fire Exit Devices ANSI A156.3, Grade 1 Lifetime Warranty BHMA CERTIFIED

More information

PUSH BAR EXIT DEVICES CROSS BAR EXIT DEVICES NARROW STILE EXIT DEVICES FEATURING LCWD STRIKES... 20

PUSH BAR EXIT DEVICES CROSS BAR EXIT DEVICES NARROW STILE EXIT DEVICES FEATURING LCWD STRIKES... 20 Exit Devices Section TABLE OF CONTENTS EXIT DEVICES PUSH BAR EXIT DEVICES N1500 Heavy Duty Rim Exit Device N1550 Rim Exit Device... 6 N1650 Fire Rated Heavy Duty Exit Device N1700(F) Vertical Rod Heavy

More information

Adams rite. Exit Devices & parts exit devices series exit device parts

Adams rite. Exit Devices & parts exit devices series exit device parts Adams rite Exit Devices & parts exit devices 8099 8211 8099 Active Dummy Bar with Switch Can be wired normally open or normally closed to operate maglock, alarm, etc No latching mechanism 8211 Surface

More information

Design Guidelines and Standards Manual University of Cincinnati

Design Guidelines and Standards Manual University of Cincinnati SECTION 08710D - A. SPECIFICATIONS FORMAT 1. It is preferred that this section include all items of door hardware. Window hardware and operators should be specified in the window section. This approach

More information

5000 & F5000 Rim Type Panic And Fire Exit Devices 5000V & F5000V Vertical Rod Panic And Fire Exit Devices ANSI A156.3, Grade 2

5000 & F5000 Rim Type Panic And Fire Exit Devices 5000V & F5000V Vertical Rod Panic And Fire Exit Devices ANSI A156.3, Grade 2 5000 & F5000 Rim Type Panic And Fire Exit Devices 5000V & F5000V Vertical Rod Panic And Fire Exit Devices ANSI A156.3, Grade 2 Features & Construction ANSI A156.3, Grade 2 heavy duty exit device in surface

More information

MODELS TRUE WOOD DOOR OPERATIONAL HARDWARE EXIT DEVICE MODELS LEVER X LEVER MODELS DOORS WITH FLUSHBOLTS:

MODELS TRUE WOOD DOOR OPERATIONAL HARDWARE EXIT DEVICE MODELS LEVER X LEVER MODELS DOORS WITH FLUSHBOLTS: MODELS EXIT DEVICE MODELS Concealed Less Bottom Rod Type D3976 Inset Exit Device Concealed Top Latch Only Rated Doors (Paired) LEVER X LEVER MODELS D3944 Classroom Function D3945 Passage Function D3946

More information

Power Transfer Devices

Power Transfer Devices Security Door Controls 4 Power Transfer Devices From frame to door, SDC s power transfer devices provide secure, concealed or vandal-resistant means to transfer power and monitoring signals to doors equipped

More information

ADAMS RITE. ADAMS RITE MANUFACTURING COMPANY Sliding Hardware/Exit Devices Series Turns

ADAMS RITE. ADAMS RITE MANUFACTURING COMPANY Sliding Hardware/Exit Devices Series Turns Sliding Hardware/ 1000 Series Turns Series 1000 turns are designed to operate Adams Rite MS 1847 deadlocks and latches. 1000-11 and 1000-21 have a rectangular escutcheon for mounting directly on the door.

More information

Dor-O-Matic Exit Devices

Dor-O-Matic Exit Devices Dor-O-Matic Exit Devices T H E F A L C O N D I F F E R E N C E S A F E T Y, S E C U R I T Y A N D U N C O M P R O M I S I N G V A L U E At Falcon, we know that every product you sell not only has to meet

More information

SERIES 500 TECHNICAL DETAILS THURSDAY, JANUARY 24, 2008

SERIES 500 TECHNICAL DETAILS THURSDAY, JANUARY 24, 2008 SERIES 500 TECHNICAL DETAILS 1. Table of Contents 2. Overall Specifications 3. Door Overall Dimensions 4. Door Construction 5. Total Preassembled Dimensions 6. Overall Frame Dimensions 7. Frame Profile

More information

FEATURES & SPECIFICATIONS. 100% internal parts quality inspection provides security, reliability and durability

FEATURES & SPECIFICATIONS. 100% internal parts quality inspection provides security, reliability and durability For Doors... 1 ¼ Backset... 2 ¾ Lockcase... FEATURES & SPECIFICATIONS Heavy gauge zinc chromate steel Front... Heavy gauge steel x 1 ¼ x 3 / 32. Accommodates flat doors and doors beveled ⅛ in Armored Front...

More information

Olympian 100, 200, 300 Series

Olympian 100, 200, 300 Series OLYMPIAN 100, 200, 300 SERIES : EXIT DEVICES Olympian 100, 200, 300 Series Exit Devices Strength by design. Simply PRECISION TABLE OF CONTENTS Exit Devices & Trims Rim Devices...4, 5 Surface Vertical Rod

More information

SERIES 700 TECHNICAL DETAILS MONDAY, JANUARY 21, 2008

SERIES 700 TECHNICAL DETAILS MONDAY, JANUARY 21, 2008 SERIES 700 TECHNICAL DETAILS 1. Table of Contents 2. Overall Specifications 3. Overall Preassembled Door Dimensions 4. Door Leaf Dimensions 5. Door Leaf Construction 6. Cylindrical Lock Preparation 7.

More information

ED5470 Panic-Listed Surface Vertical Rod Exit Device ED5470B 1-1/2 Hour Fire-Listed Surface Vertical Rod Exit Device

ED5470 Panic-Listed Surface Vertical Rod Exit Device ED5470B 1-1/2 Hour Fire-Listed Surface Vertical Rod Exit Device Surface Vertical Rod Features ED5470 Panic-Listed Surface Vertical Rod Exit Device ED5470B 1-1/2 Hour Fire-Listed Surface Vertical Rod Exit Device Features Handing Device is handed but easily field reversible.

More information

Excel Series Value Engineered Access Hardware

Excel Series Value Engineered Access Hardware Excel Series Value Engineered Access Hardware Excel E1200 Economically Priced Alternative to Low Cost Imports Quality and Flexibility for Commercial Applications. The Excel product line is designed for

More information

D-1610/D-1611 SERIES: DOOR CLOSERS. D-1610/D-1611 Series. Door Closers. Trusted experts. Proven reliability. Simply STANLEY.

D-1610/D-1611 SERIES: DOOR CLOSERS. D-1610/D-1611 Series. Door Closers. Trusted experts. Proven reliability. Simply STANLEY. D-1610/D-1611 SERIES: DOOR CLOSERS D-1610/D-1611 Series Door Closers Trusted experts. Proven reliability. Simply STANLEY. TABLE OF CONTENTS General Information...2, 3 Standard Application...4 Parallel

More information

PRICE LIST June 1, 2012

PRICE LIST June 1, 2012 June 1, 2012 TABLE OF CONTENTS Overhead Concealed Closers 4-6 Mechanical Exit Devices 45-47, 52-54 Surface Mount Closers 6-14 Electrified Exit Devices 48-51 Pedestrian Gate Closers 14 Mechanical Cylindrical

More information

COMMERCIAL DOOR HARDWARE PRODUCT CATALOG HOME DEPOT EXCLUSIVE SPECIAL ORDER PROGRAM FOR MORE INFORMATION

COMMERCIAL DOOR HARDWARE PRODUCT CATALOG HOME DEPOT EXCLUSIVE SPECIAL ORDER PROGRAM FOR MORE INFORMATION HOME DEPOT EXCLUSIVE SPECIAL ORDER PROGRAM COMMERCIAL DOOR HARDWARE PRODUCT CATALOG FOR MORE INFORMATION Find Universal Hardware in QuoteCenter Downloadable version of this catalog can be found at UniversalHardware.com

More information

cel SECURITY DOOR CONTROLS Value Engineered Access Hardware sdcsecurity.com Power Supplies Exit Switches

cel SECURITY DOOR CONTROLS Value Engineered Access Hardware sdcsecurity.com Power Supplies Exit Switches Security Door Controls cel TM Value Engineered Access Hardware Excel E1200 Excel E600 Excel E300 Excel Series Value Engineered Access Hardware from SDC Economically Priced Alternative to Low Cost Imports

More information

D O O R C L O S E R S

D O O R C L O S E R S DOOR CLOSERS DOOR CLOSER Philadelphia Hardware Group, Inc. is presenting the finest ADVANTAGE surface mounting door closers certified by BHMA including: Multi-size door closer: 9000, 8000, 6000, 6000S

More information

MONACO LOCK COMPANY, INC. TEL (800) FAX (800)

MONACO LOCK COMPANY, INC. TEL (800) FAX (800) We offer several types of faceplate options to accommodate your application. Faceplate options sold separately. The 1006 series is the strongest and most versatile electric strike available. It meets or

More information

Locksets. Requirements. Approved Manufacturers. Schlage D Series Rho Trim No Substitution Cylinders Medeco No Substitution

Locksets. Requirements. Approved Manufacturers. Schlage D Series Rho Trim No Substitution Cylinders Medeco No Substitution Locksets Requirements -All Locksets To Be Grade 1 Series 4000 Cylindrical -All Locksets To Have ADA Approved Lever Trim -All Locksets to be Dull Chrome (626) Finish -All Lock And Cylinders To Be Keyed

More information

CK4400 Series. Standard Duty Cylindrical Knob Locksets

CK4400 Series. Standard Duty Cylindrical Knob Locksets Series Standard Duty Cylindrical Knob Locksets Applications Applications An outstanding combination of value and performance. Ideal for quality residential and light commercial buildings, such as: Fine

More information

E-Plex 5700 Series E-PLEX

E-Plex 5700 Series E-PLEX PIN/PROX or Dual Credential Electronic Pushbutton Lock 3,000 Access Codes 30,000 Audit Events Access Schedules ANSI/BHMA Grade-1 Certified Features Access Control: No Wires: Locking Device Options: Number

More information

Table of Contents 30 Series Exit Device

Table of Contents 30 Series Exit Device 30 Series Exit Device Table of Contents Features, Applications and UL Fire Door Ratings... 1 3727/ NB3727 Vertical Rod Type Exit Device... 2 3828 Rim Type Exit Device...3 30 Series Trims....4 Alternate

More information

Electrified Products TABLE OF CONTENTS. P Power Supply Power Transfers Pressure Sense Bars Proximity Cards & Keys...

Electrified Products TABLE OF CONTENTS. P Power Supply Power Transfers Pressure Sense Bars Proximity Cards & Keys... TABLE OF CONTENTS A Adjustable Angle Bracket (2941/2942)... 6 Angle Brackets (2950 Series)... 9 Armature Mounting Plates (2950 Series)...7-8 C Coordinator Mounting Bracket (2950 Series)... 8 Concealed

More information

Electrified Products TABLE OF CONTENTS. P Power Supply Power Transfers Pressure Sense Bars Proximity Cards & Keys...

Electrified Products TABLE OF CONTENTS. P Power Supply Power Transfers Pressure Sense Bars Proximity Cards & Keys... TABLE OF CONTENTS A Adjustable Angle Bracket (2941/2942)... 6 Angle Brackets (2950 Series)... 9 Armature Mounting Plates (2950 Series)...7-8 C Coordinator Mounting Bracket (2950 Series)... 8 Concealed

More information

CRAFTMASTER HARDWARE CO., INC Architectural. Product Guide

CRAFTMASTER HARDWARE CO., INC Architectural. Product Guide Architectural Product Guide INTRODUCTION Norton Door Controls offers a comprehensive line of door controls designed and manufactured to ensure superior performance, reliability and application breadth.

More information

351 Series Door Closers Models: Finishes: BHMA BHMA Description

351 Series Door Closers Models: Finishes: BHMA BHMA Description Door Closers Adams Rite provides Surface Applied and Pocket Closers from Sargent for controlling the closing of The RITE Door. 351 Series The 351 Powerglide line of surface door closers has been engineered

More information

RELIANT 5000 SERIES: EXIT DEVICES. Reliant 5000 Series. Exit Devices. Strength by design. Simply PRECISION

RELIANT 5000 SERIES: EXIT DEVICES. Reliant 5000 Series. Exit Devices. Strength by design. Simply PRECISION RELIANT 5000 SERIES: EXIT DEVICES Reliant 5000 Series Exit Devices Strength by design. Simply PRECISION TABLE OF CONTENTS Exit Devices & Trims Rim Devices...4, 5 Surface Vertical Rod Devices...6, 7 Mullions

More information

3800 Series

3800 Series 3800 Series Hager 3800 Series mortise lock provides maximum security and durability for the harshest environments. With field reversible handing, ease of installation, and both escutcheon and sectional

More information

D o o r C l o s e r s

D o o r C l o s e r s Door Closers DOOR CLOSER Philadelphia Hardware Group, Inc. is presenting the fi nest ADVANTAGE surface mounting door closers for your various application demands. There are Multi-size door closer: 9000,

More information

6200 Series. Strikes for mortise or cylindrical devices. Features and benefits. Overview

6200 Series. Strikes for mortise or cylindrical devices. Features and benefits. Overview 6200 Series Strikes for mortise or cylindrical devices Overview Features and benefits Von Duprin electric strikes are known for their reliability, durability and security. The 6200 Series strikes are designed

More information

X Series. Features. comparison chart. Lock type. Glossary and finish chart. MA Series. RU Series

X Series. Features. comparison chart. Lock type. Glossary and finish chart. MA Series. RU Series Lock type finish chart MA X Grade 1, heavy-duty cylindrical knob locks RU T When you need a tough, reliable lock that can also withstand the corrosive conditions of a marine environment you need a Falcon

More information

MODELS METAL DOOR OPERATIONAL HARDWARE EXIT DEVICE MODELS LEVER X LEVER MODELS DOORS WITH PUSH OR PULL OPERATION: DOORS WITHOUT TRIM:

MODELS METAL DOOR OPERATIONAL HARDWARE EXIT DEVICE MODELS LEVER X LEVER MODELS DOORS WITH PUSH OR PULL OPERATION: DOORS WITHOUT TRIM: MODELS EXIT DEVICE MODELS Mortise Type D3375 Mortise Inset Exit Device Lock Edge Latching Rated Doors (Single Only) D8375 Mortise Inset Exit Device Lock Edge Latching Non Rated Doors (Single & Paired)

More information

5300 Series. Architectural Commercial Door Control

5300 Series. Architectural Commercial Door Control 5300 Series Architectural Commercial Door Control 5300 SERIES Architectural Commercial Door Control SUGGESTED ARCHITECTURAL SPECIFICATIONS All door closers shall be narrow projection American Eagle 5300

More information

OLYMPIAN 100, 200, 300 SERIES PRECISION HARDWARE

OLYMPIAN 100, 200, 300 SERIES PRECISION HARDWARE OLYMPIAN 100, 200, 300 SERIES PRECISION HARDWARE GENERAL INFORMATION TABLE OF CONTENTS EXIT DEVICES & TRIMS Page Rim Devices...4, 5 Surface Vertical Rod Devices...6, 7 Mortise Devices...8, 9 MULLIONS Fire

More information

W Series. Features. comparison chart. Lock type. Glossary and finish chart. MA Series. RU Series

W Series. Features. comparison chart. Lock type. Glossary and finish chart. MA Series. RU Series Lock type finish chart MA W Grade 2, medium-duty cylindrical lever and knob locks RU T Whether your application is government/military, retail, industrial or multi-family, there s a W lock that fits perfectly.

More information

DIAMOND DOOR PRODUCTS TECHNICAL DETAILS MARCH 2010

DIAMOND DOOR PRODUCTS TECHNICAL DETAILS MARCH 2010 DIAMOND DOOR PRODUCTS TECHNICAL DETAILS 1. Table of Contents 2. Overall Specifications 3. Warranty 4. Door Overall Dimensions Standard locations 5. Door Construction 6. Total Preassembled Dimensions 7.

More information

CL3500 Series. Heavy-Duty Cylindrical Lever Lockset

CL3500 Series. Heavy-Duty Cylindrical Lever Lockset Series Heavy-Duty Cylindrical Lever Lockset Applications Index Applications...2 Features... 3 Functions...4 Trim Designs...6 Options & Accessories...7 How to Order...9 Quick Codes...10 How to...11 Applications

More information

5300 Series. Architectural Door Control

5300 Series. Architectural Door Control 5300 Series Architectural Door Control 5300 SERIES ARCHITECTURAL STYLE COMMERCIAL DOOR CONTROL SUGGESTED ARCHITECTURAL SPECIFICATIONS All door closers shall be narrow projection American Eagle 5300 Series

More information

7100 Series. Heavy Duty Architectural Door Control

7100 Series. Heavy Duty Architectural Door Control 7100 Series Heavy Duty Architectural Door Control 7100 SERIES Heavy Duty Architectural Door Control SUGGESTED ARCHITECTURAL SPECIFICATIONS All door closers shall be PDQ Industries, Inc. 7100 Series with

More information

Concealed Vertical Rod Features

Concealed Vertical Rod Features Concealed Vertical Rod Features ED5800 Panic-Listed Concealed Vertical Rod Exit Device ED5800A 3-Hour Fire-Listed Concealed Vertical Rod Exit Device FOR USE WiTH METAL DOORS OnLy Features Handing Device

More information

K Series. Grade 1 cylindrical lever locks

K Series. Grade 1 cylindrical lever locks K Series Grade 1 cylindrical lever locks Falcon K Series 4 Overview 5 Features and specifications 6 Designs and finishes 7 Functions 8 Cylinders 9 Competitive keyways 10 Options and accessories 11 Competitive

More information

Auxiliary Locks. Deadlocks and Deadbolts. Falcon Monarch Dor-O-Matic

Auxiliary Locks. Deadlocks and Deadbolts. Falcon Monarch Dor-O-Matic Auxiliary Locks Deadlocks and Deadbolts Falcon Monarch Dor-O-Matic T H E F A L C O N D I F F E R E N C E F A L C O N A U X I L I A R Y L O C K S S A F E T Y, S E C U R I T Y A N D U N C O M P R O M I S

More information

CONCEALED CLOSER SERIES

CONCEALED CLOSER SERIES CLOSER SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of

More information

Door Controls DOOR CLOSERS

Door Controls DOOR CLOSERS Door Controls Hager door closers offer architects, contractors, and building owners a superior product with proven reliability. In fact, our 5100, 5200, and 5300 Series Grade 1 models are the only closers

More information

Simplex. Cylindrical Knob Series. Grade 1 Extra Heavy Duty Cylindrical Knob

Simplex. Cylindrical Knob Series. Grade 1 Extra Heavy Duty Cylindrical Knob Cylindrical Knob Series Grade 1 Extra Heavy Duty Cylindrical Knob SPXCK100 F82 Entry/Office Lock Push Button locking. Pushing button in inside knob locks outside lever until unlocked with key or turning

More information

Door Closer Cycle. How to Select the Proper Closer. Things to Consider

Door Closer Cycle. How to Select the Proper Closer. Things to Consider Door Control Closer Spring Adjustment Not Shown in Door Closer Cycle Diagram Effects the entire cycle of the door closer movement Used to size closer for application requirements Determines the amount

More information

Concealed overhead closer for high-end applications DOOR CLOSERS CATALOG

Concealed overhead closer for high-end applications DOOR CLOSERS CATALOG Concealed overhead closer for high-end applications 7900 S E R I E S DOOR CLOSERS CATALOG INTRODUCTION The 7900 Series Overhead Concealed Closers offer extremely durable operation with the vandal resistance

More information

268, 269 & 278. Concealed Door Closers

268, 269 & 278. Concealed Door Closers 268, 269 & 278 Concealed Door Closers Copyright 2004-2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents General Information....3 268 Features and Benefits...4

More information

3100 Series. Commercial Door Control

3100 Series. Commercial Door Control 3100 Series Commercial Door Control 3100 SERIES COMMERCIAL Door Control SUGGESTED ARCHITECTURAL SPECIFICATIONS All door closers shall be American Eagle 3100 Series with full rack and pinion construction,

More information

DC3000 Series. Door Closers

DC3000 Series. Door Closers Door Closers Table of Contents Applications 2 Features 3 & 4 Mountings 5 & 6 Door Closer Arms 7 & 8 Mounting Brackets 9 Brackets and Covers 10 Size and Handing 11 How to Order 12 Quick Codes 13 Helpful

More information

GRADE 2 HEAVY & STANDARD DUTY CYLINDRICAL LOCKS

GRADE 2 HEAVY & STANDARD DUTY CYLINDRICAL LOCKS GRADE 2 HEAVY & STANDARD DUTY CYLINDRICAL LOCKS Division 8 5 YEAR WARRANTY ANSI/BHMA 156.2 GRADE 2 SPECIFICATION UNISON HARDWARE, INC. www.inoxproducts.com Version: 2015.10 TABLE OF CONTENTS How to Order

More information

5300 Series 5300 SERIES

5300 Series 5300 SERIES 5300 Series Hager 5300 Series Grade 1 door closer is ideal for schools, hospitals, and other high abuse and high traffic environments. It is constructed of an aluminum alloy and provides smooth door control.

More information

Recessed. Touch bar exit devices

Recessed. Touch bar exit devices Recessed Touch bar exit devices Table of contents 3 2390 Concealed vertical rod device 4 Accessories 5 Power supply 6 Door application 7 How to order The Falcon difference Safety, security and uncompromising

More information

Architectural Commercial Door Control

Architectural Commercial Door Control 5300 Series Slim Line Architectural Commercial Door Control 5300 SERIES SLIM LINE Architectural Commercial Door Control All door closers shall be narrow projection American Eagle 5300 Series with full

More information

Electrified Lockset 74 SECURITY DOOR CONTROLS

Electrified Lockset 74 SECURITY DOOR CONTROLS Locking Devices 1 Security Door Controls Electrified Lockset Building and fire life safety code compliant for fire rated office doors, corridor doors, lobby doors, exit doors and stairwell doors. HiTower,

More information

Overhead Door Holders/Stops

Overhead Door Holders/Stops Overhead Door Holders/Stops 08 71 00/ING BuyLine 7155 STEELCRAFT SINGLE ACTING DOORS, INTERIOR/EXTERIOR APPLICATIONS, REVERSIBLE, NON-HANDED 450 Series Surface-mounted holders and stops offer the widest

More information

T H E F A L C O N D I F F E R E N C E

T H E F A L C O N D I F F E R E N C E T H E F A L C O N D I F F E R E N C E S E C U R I T Y A N D U N C O M P R O M I S I N G V A L U E At Falcon, we know that every product you spec not only has to meet local building codes, but also your

More information

DOUBLE LEVER ARM DOUBLE LEVER ARM SINGLE LEVER ARM 5010 SINGLE LEVER ARM

DOUBLE LEVER ARM DOUBLE LEVER ARM SINGLE LEVER ARM 5010 SINGLE LEVER ARM SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of the closer.

More information

3400 Series

3400 Series 3400 Series Hager 3400 Series Grade 1 lock is designed and engineered to withstand the most abusive environments. We ve categorized it extra heavy duty and you can rest assured that it has been tested

More information

APEX 2000 SERIES: TOUCHBAR EXIT DEVICES. Apex 2000 Series. Touchbar Exit Devices. Strength by design. Simply PRECISION

APEX 2000 SERIES: TOUCHBAR EXIT DEVICES. Apex 2000 Series. Touchbar Exit Devices. Strength by design. Simply PRECISION APEX 2000 SERIES: TOUCHBAR EXIT DEVICES Apex 2000 Series Touchbar Exit Devices Strength by design. Simply PRECISION TABLE OF CONTENTS Wide Stile Exit Devices & Trims Rim Devices...4, 5 Surface Vertical

More information

Corbin Russwin. Latches, cylinders, interchangeable CORE & spindle. Latches. Lockset Cylinders. Rim Cylinders. Interchangeable Core.

Corbin Russwin. Latches, cylinders, interchangeable CORE & spindle. Latches. Lockset Cylinders. Rim Cylinders. Interchangeable Core. Latches Corbin Russwin Latches, cylinders, interchangeable CORE & spindle Mfg # Series Backset EZ # 486F90 626 4200 2-3/4 035270 Lockset Cylinders Mfg # Series Keyway EZ # 2000 052 59A1 626 4200, 5200

More information

An ASSA ABLOY Group brand Series. Flatbar Exit Devices

An ASSA ABLOY Group brand Series. Flatbar Exit Devices An ASSA ABLOY Group brand 1800 Series Flatbar Exit Devices introduction Yale 1800 series exit devices are the ideal choice for economy commercial applications where consistent quality, ease of use and

More information

5100 Series. Architectural Door Control

5100 Series. Architectural Door Control 5100 Series Architectural Door Control 5100 SERIES ARCHITECTURAL STYLE COMMERCIAL DOOR CONTROL SUGGESTED ARCHITECTURAL SPECIFICATIONS All door closers shall be American Eagle 5100 Series with full rack

More information

MA Series. Mortise Lockset Functions. MA101 FO1 Passage Latchset Latchbolt by knobs/levers at all times.

MA Series. Mortise Lockset Functions. MA101 FO1 Passage Latchset Latchbolt by knobs/levers at all times. MA Series Mortise Lockset Functions ANSI MA101 FO1 Passage Latchset Latchbolt by knobs/levers at all times. MA301 F02 Privacy Lock Latchbolt by knobs/levers, deadbolt by turn inside or emergency key outside.

More information

FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE

FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke barrier doors.

More information

E-Plex 5700 Series E-PLEX

E-Plex 5700 Series E-PLEX PIN/PROX or Dual Credential Electronic Pushbutton Lock 3,000 Access Codes 30,000 Audit Events Access Schedules ANSI/BHMA Grade-1 Certified Features Access Control: No Wires: Locking Device Options: Number

More information

EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES

EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES WIKK INDUSTRIES, INC. MasterFormat 95 SECTION 08480 MasterFormat 04 SECTION 08 42 36 EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES PART 1 GENERAL 1.1 DESCRIPTION A. Work included: Entrance and vestibule

More information

EXIT DEVICES Reliant 5000 Series

EXIT DEVICES Reliant 5000 Series PRECISION HARDWARE EXIT DEVICES Reliant 5000 Series GENERAL INFORMATION TABLE OF CONTENTS EXIT DEVICES & TRIMS Page Rim Devices...4, 5 Surface Vertical Rod Devices...6, 7 MULLIONS Fire Labeled Removable

More information

stanley door closers d-4550/d-4551 D-4550 / D-4551 SERIES DOOR CLOSERS

stanley door closers d-4550/d-4551 D-4550 / D-4551 SERIES DOOR CLOSERS stanley door closers d-4550/d-4551 D-4550 / D-4551 SERIES DOOR CLOSERS 1 General InForMatIon table of contents Page General Information... 2 4 How To Order...4 Standard (Pull) Application...5 Parallel

More information

Corbin Russwin. Locksets & Deadbolt. ck4200 series grade 1 heavy duty locksets. CK4400 Series Grade 2 Medium Duty Locksets. Dl4011 Mortise Deadbolt

Corbin Russwin. Locksets & Deadbolt. ck4200 series grade 1 heavy duty locksets. CK4400 Series Grade 2 Medium Duty Locksets. Dl4011 Mortise Deadbolt ck4200 series grade 1 heavy duty locksets Corbin Russwin Locksets & Deadbolt Ideal for demanding, high-use commercial, industrial and institutional applications Steel chassis, zinc dichromate plated for

More information

Accessories 286 SDC SECURITY DOOR CONTROLS

Accessories 286 SDC SECURITY DOOR CONTROLS 8 Security Door Controls From wireless remote controls to durable door holding & release devices, to REX sensors, timers, ball and magnetic switches, and from concealed contact to universal mounting enclosure

More information

Multi-sized cast iron closer for high use applications DOOR CLOSER CATALOG

Multi-sized cast iron closer for high use applications DOOR CLOSER CATALOG Multi-sized cast iron closer for high use applications 9500 S E R I E S DOOR CLOSER CATALOG INTRODUCTION Ideal for high use openings, the Norton 9500 Series Cast Iron door closer offers the durability,

More information

FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES

FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke

More information

General Information 351 Series Powerglide

General Information 351 Series Powerglide General Information Closer Spring Adjustment (not shown) Effects the entire cycle of the door closer movement Used to size closer for application requirements Determines the amount of force with which

More information

4000 Series Exit Devices Premier Product

4000 Series Exit Devices Premier Product 4 4000 Series Exit Devices Premier Product Certification & Compliance: u ANSI/BHMA A56., Grade ANSI A7. Accessibility Code Underwriters Laboratories (UL and CUL) listed for accident hazard (panic) standard.

More information

98/99 Series. Exit devices

98/99 Series. Exit devices 98/99 Series Exit devices Introduction Exit devices are a critical part of the fire and life safety egress system and will provide safe and reliable service when properly applied and maintained. Von Duprin

More information

Exit Devices Rainer Security Products Ltd

Exit Devices Rainer Security Products Ltd Exit Devices Rainer Security Products Ltd Unit B6, Rudford Industrial Estate, Ford, Arundel, West Sussex BN18 0BF +44 (0) 190 72211 rainersecurity.co.uk sales@rainersecurity.co.uk 2 S1150 & S1250 Series

More information

Entry. Entry. Entry. Entry

Entry. Entry. Entry. Entry Functions x 9800/9M800 AC2 Exit Device Outside Inside Series/Function Type Function Description ED5200(A) & ED5200S(A) *9833 Without Cylinder Outside lever locked (freewheeling) except when in passage

More information

MB1 Series ANSI Grade 1 Extra Heavy Duty Lever Locks

MB1 Series ANSI Grade 1 Extra Heavy Duty Lever Locks MB1 Series ANSI Grade 1 Extra Heavy Duty Lever Locks FEATURES: Heavy duty chassis with various lever styles available. Strong cast and machined stainless steel hubs, mounted with heavy duty return springs.

More information

Light/Medium-Duty Knob Locksets. CK4700 Series

Light/Medium-Duty Knob Locksets. CK4700 Series Light/Medium-Duty Knob Locksets CK4700 Series Applications Quality The CK4700 series is a Grade 2 light/medium-duty knob lockset which provides an outstanding combination of value and performance. It is

More information

Non-handed, pre-assembled for left hand door installation easily changed in the field

Non-handed, pre-assembled for left hand door installation easily changed in the field PIN Access Electronic Pushbutton Lock 100 Access Codes Cylindrical Features Access Control: No Wires: Locking Device Options: Number of Codes: Handing: Programming: Key Override (Optional): Operation Modes:

More information

7 LINE CYLINDRICAL LEVER LOCK

7 LINE CYLINDRICAL LEVER LOCK 7 LINE CYLINDRICAL LEVER LOCK Specifications Table of Contents Lever Designs, Features, Benefits & Applications........................... 1 Functions..........................................................

More information

7100 Series. Heavy Duty Architectural Door Control

7100 Series. Heavy Duty Architectural Door Control 7100 Series Heavy Duty Architectural Door Control 7100 SERIES HEAVY DUTY ARCHITECTURAL STYLE DOOR CONTROL SUGGESTED ARCHITECTURAL SPECIFICATIONS All door closers shall be American Eagle 7100 Series with

More information

CONCEALED CLOSER SERIES

CONCEALED CLOSER SERIES CONCEALED CLOSER SERIES APPLICATIONS n For aluminum, hollow metal, or wood doors and frames. n Can be used with hinge or pivot mounted door. n Closers for 4 or minimum 1-3/4 head frame or 4 top rail. n

More information