GTI PRO LITE HVLP & LVMP Operation Manual

Transcription

1 GTI PRO LITE HVLP & LVMP Operation Manual 1

2 Table of Contents EC DECLARATION OF CONFORMITY... 3 PART NUMBERS... 3 OPERATIONAL DESCRIPTION... 3 KIT CONTENTS (ALL MODELS)... 4 CONSTRUCTION FEATURES... 4 MATERIALS OF CONSTRUCTION... 4 SPECIFICATIONS & TECHNICAL DATA... 4 SAFETY WARNINGS... 5 PARTS LIST... 6 SERVICE PARTS... 6 INSTALLATION... 8 OPERATION... 8 PREVENTIVE MAINTENANCE & CLEANING... 8 PARTS REPLACEMENT/MAINTENANCE... 9 AIR VALVE INSTRUCTIONS... 9 NEEDLE PACKING REPLACEMENT INSTRUCTIONS SPREADER VALVE ASSEMBLY REPLACEMENT/MAINTENANCE FLUID SUPPLY INSERT SPRAY HEAD SEAL REPLACEMENT PARTS REPLACEMENT/MAINTENANCE TROUBLESHOOTING POSSIBLE PROBLEMS IN OPERATION ACCESSORIES

3 EC Declaration of Conformity We, Finishing Brands UK Limited, Ringwood Rd, Bournemouth, Dorset, BH11 9LH, UK, as the manufacturer of the Spray gun model GTIPRO LITE G, declare, under our sole responsibility, that the equipment to which this document relates is in conformity with the following standards or other normative documents: BS EN ISO 12100: 2010, BS EN 1953:2013; and thereby conform to the protection requirements of Council Directive 2006/42/EC relating to Machinery Safety Directive, and; EN :2009, council Directive 94/9/EC relating to Equipment and Protective Systems intended for use in Potentially Explosive Atmospheres protection level II 2 G X. D. Smith, Director of Sales (EMEA) 5th May 2016 Finishing Brands UK Limited reserves the right to modify equipment specification without prior notice. Part Numbers The ordering code for the GTIPRO LITE G Spray gun is; Operational Description E.g. PROLT-GTE10-12 where; G = Gravity Gun TE10 = TE10 Aircap 12 = 1.2 Nozzle See charts 1 & 2 p13 for available Aircap/Nozzle sizes This GTIPRO LITE G Spray Gun is a professional quality gun designed with both high volume, low pressure (HVLP) technology or High Efficiency EPA compliant technology. HVLP Technology reduces overspray and limits air cap pressure to 0.7 bar (10 psi). High Efficiency complies with EPA by obtaining transfer efficiency above 65%. IMPORTANT: These Sprayguns are suitable for use with both waterbased and solvent based coating materials. These guns are not designed for use with highly corrosive and/or abrasive materials and if used with such materials it must be expected that the need for cleaning and/or replacement of parts will be increased. If there is any doubt regarding the suitability of a specific material, contact your DeVilbiss Distributor or DeVilbiss direct. NOTE: This gun is not to be used with halogenated hydrocarbon solvents or cleaning agents such as 1,1,1,-Trichloroethane or methylene chloride. These solvents can react with the aluminium components used in this gun and cup. The reaction can become violent and lead to an equipment explosion. 3

4 Kit contents (all models) 1 GTIPRO LITE Gravity Feed Spraygun 1 Spanner (10mm and 14mm A/F) 1 GFC Gravity feed cup 1 Torx/Flat blade screwdriver 1 Cup Filter 1 Cleaning Brush 1 Set of 4 coloured identification rings 1 Service bulletin Construction Features 1 Air Cap (nickel plated brass for long durability) 10 Fan Air Adjustment (stepless regulation for fan to round spray) 2 Air Cap Retaining Ring (allows easy rotation of air cap) 11 Fluid Adjustment (stepless regulation of fluid volume) 3 Fluid Nozzle (ideal for most paint systems) 12 Interchangeable Colour ID System (4 coloured rings supplied) 4 Fluid Needle (grooved stem for easy removal) 13 Anodised, forged aluminium gun body (ergonomic, good looking & durable, easy to clean) 5 Fluid Inlet (3/8 BSP thread accepts DeVilbiss and cc Acetal Cup (easy clean, anti-static) most other cup systems) 6 Air Inlet (universal thread, accepts G 1/4 & 1/4 NPS) 15 Cup Lid with Drip Free Vent (avoid drips) 7 Self Adjusting Needle Packing (for trouble free operation) 16 Air Valve (design offers low pull force & low pressure drop) 8 Trigger (ergonomic for comfort) 17 Gun acceptable for waterborne and solvent borne applications 9 Trigger Stud & Screw (easy replacement design) Materials of Construction Gun Body Anodised aluminium Air Cap Nickel Plated Brass Fluid Nozzle, Fluid Needle, Fluid Inlet, Trigger Stud Stainless steel Adjusting Knobs, Air Cap Retaining Ring Anodized aluminium Springs, Clips, Screws Stainless steel Seals, Gaskets Solvent resistant Trigger Chrome plated steel Air Inlet, Body Bushing, Spreader Valve Body, Air Valve Chrome plated brass Nut. Air Valve Assembly Aluminium Air Supply Connection Maximum Static Air Inlet Pressure Specifications & Technical Data Gun Air Inlet Pressure for HVLP and High Efficiency both with gun triggered. Fluid Supply Connection Service Temperature Gun Weight (gun only) (with cup) Universal 1/4" BSP and 1/4" NPS male P1 = 12 bar (175 psi) 0.69 bar (10 psi) 2.0 bar (29 psi) 3/8" BSP 0 to 40 C (32 to 104 F) 446 g 623 g 4

5 SAFETY WARNINGS Fire and explosion Solvents and coating materials can be highly flammable or combustible when sprayed. ALWAYS refer to the coating material supplier s instructions and COSHH sheets before using this equipment. Users must comply with all local and national codes of practice and insurance company requirements governing ventilation, fire precautions, operation and house-keeping of working areas. This equipment, as supplied, is NOT suitable for use with Halogenated Hydrocarbons. Static electricity can be generated by fluid and/or air passing through hoses, by the spraying process and by cleaning non-conductive parts with cloths. To prevent ignition sources from static discharges, earth continuity must be maintained to the spray gun and other metallic equipment used. It is essential to use conductive air and/or fluid hoses. Personal Protective Equipment Toxic vapours When sprayed, certain materials may be poisonous, create irritation or be otherwise harmful to health. Always read all labels, safety data sheets and follow any recommendations for the material before spraying. If in doubt, contact your material supplier. The use of respiratory protective equipment is recommended at all times. The type of equipment must be compatible with the material being sprayed. Always wear eye protection when spraying or cleaning the spray gun. Gloves must be worn when spraying or cleaning the equipment. Training Personnel should be given adequate training in the safe use of spraying equipment. Misuse Never aim a spray gun at any part of the body. Never exceed the maximum recommended safe working pressure for the equipment. The fitting of non-recommended or non-original spares may create hazards. Before cleaning or maintenance, all pressure must be isolated and relieved from the equipment. The product should be cleaned using a gun-washing machine, and should be removed and dried immediately after cleaning is completed. Prolonged exposure to cleaning solutions can cause damage to the product. Noise Levels The A-weighted sound level of spray guns may exceed 85 db (A) depending on the setup being used. Details of actual noise levels are available on request. It is recommended that ear protection is worn at all times when spraying. Operating Spray equipment using high pressures may be subject to recoil forces. Under certain circumstances, such forces could result in repetitive strain injury to the operator. 5

6 PARTS LIST REF. NO. DESCRIPTION PART NO. QTY REF. NO. DESCRIPTION PART NO. QTY 1 Air Cap Retaining Ring Air Inlet Slip Ring Colour ID Ring Kit (4Colours) SN-26-K4 1 3 Air Cap Air Inlet Kit SN-9-K 1 4 Air Cap Retaining Clip JGA-156-K Needle Packing Retaining Ring Seal Packing Spring Aircap & Ring 7 Air Cap Retaining Ring & Seal 8 Fluid Nozzle Kit See chart 1 p13 PRO-420-K 1 *37 See chart 2 p13 36 Packing Nut - 1 Packing, Spring and Packing Nut Kit SN-404-K 1 1 *38 Trigger Screw Spray Head Trigger - 1 *10 Spray head Seal SN-18-1-K2 1 *40 Trigger Stud Spray head kit SN-69-K 1 41 Trigger Stud & Screw Kit SP617-CR-K 1 *12 Circlip Airflow Valve PRO-407-K 1 13 Valve Body Circlip - Kit of K5 1 *14 O Ring Valve Head - 1 *15 Spreader Valve Pin Washer Spreader Valve Adjusting Knob Spreader Valve Assembly Valve Body - 1 PRO-406-K 1 47 Valve Adjusting Knob Front Valve Seal Filter KGP-5-K Valve Seat Gravity Cup Spindle Gravity Cup Lid GFC Air Valve Spring Drip Check Lid (kit of 5) GFC-2-K Rear Valve Seal Gravity Cup Kit GFC Air Valve Kit PRO *53 Air Valve Service Tool Fluid Needle PRO-301-K 1 54 Tool kit SN Needle Spring - 1 SERVICE PARTS 26 Spring Pad Housing SN-66-K 1 28 Fluid Adjusting Knob SN-67-C-K 1 *29 Needle Spring Kit PRO-472-K3 1 Spray Gun repair kit (includes items marked *) Seal and Pin Kit, kit of 5 (items 12, 14 and 15) PRO-470 GTI-428-K5 30 Gunbody - 1 * Not included in the Gun Kit, only with ref 23 6

7 7

8 INSTALLATION For maximum transfer efficiency, do not use more pressure than is necessary to atomise the material being applied. NOTE: when using the HVLP do not exceed 1.75 bar inlet pressure. 1. Connect the gun to a clean, moisture and oil free air supply using a conductive hose, of at least 8 mm I.D. Note Depending on hose length, larger I.D. hose may be required. Install an air gauge at the gun handle. When gun is triggered on, adjust regulated pressure to 2.0 bar for High Efficiency Aircaps and 1.75 bar for HVLP. Do not use more pressure than is necessary to atomise the material being applied. Excess pressure will create additional overspray and reduce transfer efficiency. Note If quick connect couplings are required, use only high flow quick connects approved for HVLP use. Other types will not flow enough air for correct gun operation. Note If an air adjusting valve is used at the gun inlet, use DGIPRO-502-BAR Digital Gauge. Some competitive adjusting valves have significant pressure drop that can adversely affect spray performance. The DGIPRO Digital Gauge has minimal pressure drop, which is important for HVLP spraying. 2. Insert the filter (48) into the inlet of the Gravity Cup. Make sure the body of the filter is pushed fully so the body of the filter does not protrude from the cup insert. 3. Attach the gravity feed cup to the material inlet. Note Before using the gun, flush it with solvent to ensure that the fluid passages are clean. OPERATION 1. Mix coating material to manufacturer s instructions and strain material. 2. Fill the cup to no more than 20 mm from the top of the cup. DO NOT OVERFILL. 3. Attach Cup Lid. 4. Turn fluid adjusting knob (28) clockwise to prevent fluid needle movement. 5. Turn spreader valve adjusting knob (16) counter clockwise to fully open. 6. Adjust inlet air pressure if required. 7. Turn fluid adjusting knob (28) counter clockwise 5 turns for full needle travel. 8. Test spray. If the finish is too dry, reduce airflow by reducing air inlet pressure. 9. If finish is too wet, reduce fluid flow by turning fluid adjusting knob (28) clockwise. If atomisation is too coarse, increase inlet air pressure. If too fine, reduce inlet pressure. 10. The pattern size can be reduced by turning spreader valve knob (16) clockwise. 11. Hold gun perpendicular to surface being sprayed. Arcing or tilting may result in uneven coating. 12. The recommended spray distance is mm. 13. Spray edges first. Overlap each stroke a minimum of 75%. Move gun at a constant speed. 14. Always turn off air supply and relieve pressure when gun is not in use. PREVENTIVE MAINTENANCE & CLEANING To clean air cap and fluid nozzle, brush exterior with a stiff bristle brush. If necessary to clean cap holes, use a broom straw or toothpick if possible. If a wire or hard instrument is used, extreme care must be used to prevent scratching or burring of the holes which will cause a distorted spray pattern. To clean fluid passages, remove excess material from cup, then flush with gun wash solution. Wipe the gun exterior with a dampened cloth. Never completely immerse in any solvent or cleaning solutions as this is detrimental to the lubricants and life of the spray gun. Note When replacing the fluid nozzle or fluid needle, replace both at the same time. Using worn parts can cause fluid leakage. See page 13, Chart 2. Also, replace the needle packing at this time. Torque the fluid nozzle to Nm. Do not over tighten. CAUTION To prevent damage to fluid nozzle (8) or fluid needle (24), be sure to either 1) pull the trigger and hold while tightening or loosening the fluid nozzle, or 2) remove fluid adjusting knob (28) to relieve spring pressure against needle collar. CAUTION IMPORTANT - the Gravity cup is made from special anti-static materials, but it is still important to avoid generating static charges. The Cup must not be cleaned or rubbed with a dry cloth or paper. It is possible to generate a static charge by rubbing which, if discharged to an earthed object could create an incendive spark and cause solvent vapours to ignite. Only use a dampened cloth or antistatic wipes if manual cleaning is required within a hazardous area.

9 Parts Replacement/Maintenance AIR VALVE INSTRUCTIONS Servicing Air Valve Reasons to service air valve: A) Air valve not functioning correctly (may need cleaning). B) Routine maintenance. C) Air leaks. 1. Remove trigger screw (38) with Torx tool (55) or Torx T20 key. (See fig 2). 2. Remove trigger stud (40) and remove trigger (39) (See fig 3). 3. Remove fluid adjusting knob (28) and spring (29). (See fig 4). 4. Remove fluid needle (24) (See fig 5). 5. Using a 6mm hex key, remove Valve housing (27). (See Figs 6 and 7). 6. Remove spring (21) and valve spindle (20). (See Fig 8). 7. Using service tool (53), engage groove behind the valve seat (19) (See Fig 9).

10 8. Withdraw the valve seat (19) from the gun body. (See fig 10). 9. Push out the front airvalve seal (18) with a finger. (See fig 11). 10. Turn the Gun upside down and let the seal fall out. (See fig 12). 11. Fit New front seal (18) to service tool (53). Fit into gunbody and press firmly to ensure Seal is engaged. (See fig 13). 12. Fit a new valve seat (19) to service tool (53). Groove must face outwards. (See fig 14). 13. Fit valve seat (19) to gunbody. (See fig 15). 14. Remove rear airvalve seal (22) from housing (27) with a hooked instrument. (See fig 16). 15. Fit new seal (22) to service tool (53). Groove must face outwards. Press seal (22) to housing (27). (See fig 17). 16. Reassemble remaining parts in reverse order - valve (20), spring (21), housing (27) and tighten with 6mm hex key, needle (24) spring (29) and knob (28). Replace trigger (39), fitting trigger stud (40), and screw in the trigger screw (38) with Key (55) or Torx Key T Trigger gun fully and screw in fluid adjusting knob (28) until it stops. Back it off 1/2 turn and gun will have full needle travel. 18. Trigger gun several times to verify correct operation. 10

11 Parts Replacement/Maintenance NEEDLE PACKING REPLACEMENT INSTRUCTIONS 1. Remove trigger and needle following steps 1 to 6 on P9, servicing airvalve. 2. Loosen and remove packing nut using Key (57) or a straight blade screwdriver. (See figs 18 & 19) 3. Discard old packing (34) and packing spring (35) if replacing. Clean packing if reusing. Also clean packing spring and nut (36). (See fig 20). 4. Re-assemble the packing, assemble into gunbody by hand and then tighten. (See fig 21) 5. Complete re-assembly following 16 to 24 on P10. SPREADER VALVE ASSEMBLY REPLACEMENT/MAINTENANCE The spreader valve assembly can be replaced if damaged. Remove using 14 mm Spanner (56) (See figs 22 & 23). The internal seal can be replaced and is included in the Gun Rebuild Kit (See fig 24). FLUID SUPPLY INSERT The fluid insert and seal are NOT replaceable. (See fig 25). Do not remove these parts. No maintenance is required for these parts other than regular cleaning of the internal bore. 11

12 Parts Replacement/ Maintenance SPRAY HEAD SEAL REPLACEMENT 1. Remove air cap and retaining ring (6). (See fig 26). 2. Remove fluid adjusting knob (28), spring (25), and spring pad (26). (See fig 27). 3. Remove fluid needle (24) from gun body. (See fig 28). 4. Remove fluid nozzle using 10mm Spanner (56) (See fig 29). 5. Remove spray head (9) and Seal (10) (See fig 30). 6. Remove seal (10) from spray head. (See fig 31). 7. Clean front of gun if required, using a soft brush, as well as the fluid nozzle, air cap, and retaining ring. 8. Place a new seal (10) into the front of the gun, making sure the flat of the seal is aligned to the flat in the gun. (See fig 32). 9. Fit the spray head (9), making sure the pin is engaged into the hole in the gunbody. (See fig 33). 10. Fit fluid nozzle (8), air cap and retaining Ring (6). Torque the fluid nozzle to Nm ( lbs.in). Do not over torque the fluid nozzle. (See figs 34, and 35) 11. Reassemble remaining parts in reverse order - fluid needle (24), Needle spring and pad (29), and fluid adjusting knob (28). 12. Trigger gun fully and screw in fluid adjusting knob (28) until it stops. Back it off 1/2 turn and gun will have full needle travel. 13. Trigger gun several times to verify correct operation. 12

13 Parts Replacement/Maintenance Chart 1 Air Caps PART No. FOR AIR CAP TECHNOLOGY MARKING ON AIR CAP RECOMMENDED INLET PRESSURE (bar) PROLT-GTE LVMP TE PROLT-GTE LVMP TE PROLT-GHV HVLP HV PROLT-GT LVMP T AIR FLOW 2 bar NOTE: When removing air cap from retaining ring, don t remove the Slip Ring (2) or Retaining Ring Seal (5) from the Retaining Ring. Damage to the parts may occur. Slip ring and Retaining Ring seal are not available as replacements. Simply wipe parts clean and reassemble with new or clean air cap. Chart 2 Fluid Nozzle Range & Fluid Needle PART No. FOR FLUID NOZZLE PART No. NEEDLE PRO K PRO K PRO-301-K PRO K NOTE: When replacing the fluid nozzle or fluid needle, replace both at the same time. Torque to Nm ( lbs.in). Do not over tighten the fluid nozzle. Use SN-28 (56) 10mm Spanner supplied with the gun and check with a torque wrench. 13

14 Troubleshooting Possible Problems in Operation CONDITION CAUSE CORRECTION Heavy top or bottom pattern Heavy right or left side pattern Horn holes plugged. Obstruction on top or bottom of fluid nozzle. Cap and/or nozzle seat dirty. Left or right side horn holes plugged. Dirt on left or right side of fluid nozzle. Clean. Ream with non-metallic point. Clean. Clean. Clean. Ream with nonmetallicpoint. Clean. Remedies for the top-heavy, bottom-heavy, right-heavy, and left-heavy patterns: 1. Determine if the obstruction is on the air cap or the fluid nozzle. Do this by making a test spray pattern. Then, rotate the cap one-half turn and spray another pattern. If the defect is inverted, obstruction is on the air cap. Clean the air cap as previously instructed. Also check for dried paint just inside the cap centre hole opening; remove by washing with solvent. 2. If the defect is not inverted, it is on the fluid nozzle. Clean nozzle. If problem persists, renew nozzle. Heavy centre pattern Spreader adjustment valve set too low. Atomising pressure too low. Material too thick. Turn out counter clockwise to achieve correct pattern. Increase pressure. Thin to correct consistency Split spray pattern Jerky or fluttering spray Air pressure too high. Fluid adjusting knob turned in too far. Spreader adjusting valve set too high. Loose or damaged fluid nozzle/seat Loose or broken cup fluid nipple Material level too low Container tipped too far Obstruction in fluid passage Loose fluid needle packing nut Damaged fluid needle packing Reduce at regulator or gun handle. Turn out counter clockwise to achieve correct pattern. Turn in clockwise to achieve correct pattern. Tighten or replace Tighten or replace cup Refill Hold more upright Back flush with solvent Tighten Replace 14

15 Troubleshooting Possible Problems in Operation (cont) Starved spray pattern Excessive overspray Dry spray Inadequate material flow Blocked vent in Cup lid Low atomisation air pressure Air pressure to high. Gun too far from work surface. Air pressure too high. Gun too far from work surface. Gun motion too fast. Fluid flow too low. Wind fluid adjusting knob out or change to larger fluid nozzle size Clean lid and unblock vent Increase air pressure and rebalance gun. Reduce air pressure. Adjust to correct distance. Reduce air pressure. Adjust to correct distance. Slow down. Wind out needle adjusting screw or use larger nozzle size. Fluid leaking from packing nut Packing worn. Replace. Fluid leaking or dripping from front of gun Fluid dripping or leaking from bottom of cup Runs and sags Fluid nozzle or fluid needle worn or damaged. Foreign matter in fluid nozzle. Fluid needle dirty or stuck in needle packing Wrong size fluid needle or fluid nozzle. Cup loose on gun. Cup fluid inlet seat dirty. Too much material flow. Material too thin. Gun tilted on an angle, or gun motion too slow. Replace fluid nozzle and fluid needle. Clean. Clean. Replace fluid nozzle and fluid needle. Tighten Clean. Turn fluid adjusting knob clockwise or switch to smaller fluid nozzle and fluid needle size. Mix correctly or apply light coats. Hold gun at right angle to work and adapt to correct gun technique. 15

16 ACCESSORIES Spanner Gun Stand GFV-50-F Torx driver SN cc Mixing Cups pack of 50 MC-1-K50 Cleaning Brush Air Valve (with gauge) HAV-501-B Cleaning Brush (5 pieces) K3 Air Valve (with gauge) HAV-502-B Torx driver SPN-8-K2 DGi PRO Digital Pressure Gauge DGIPRO-502- BAR DIVISION Ransburg Japan KK HP DEVILBISS is a registered trademark of Carlisle Fluid Technologie s. Jupiter is a registered trademark of CFT Ransburg Japan KK Carlisle Fluid Technologies GTi Pro LITE 16