A7 DVD Entertainment System Installation Guide

Size: px
Start display at page:

Download "A7 DVD Entertainment System Installation Guide"

Transcription

1 A7 DVD Entertainment System Installation Guide BEFORE YOU START THE INSTALLATION, READ THIS GUIDE! The Rosen A7 is the easiest-to-install DVD entertainment system available today. Even though it is very easy to install, we still strongly recommend reading this guide before starting the installation! Below is an outline of the installation process, showing the installation sequence we recommend, and the pages that describe each step. Contents - Steps to a successful installation: Step One: Make sure you have all the components and tools you ll need 2 Step Two: Check out the vehicle and plan your work - console location, harness routing, etc. 3 Step Three: Cut the headliner and mount the Bracket 4-8 Step Four: Route the harnesses and make all wiring connections 9 Connecting the Domelight Harness 10 Step Five: Install the A7 and the FM Modulator 11 Step Six: Test the system, reassemble the vehicle trim panels, quickly test one more time, and you re finished! 12 Frequently Asked Questions 13 A7 System Diagram 14 A7 Installation Manual Revision C (090303) RES PN Copyright 2003 Rosen Entertainment Systems 866-Go Rosen NOTICE OF INTENDED INSTALLATION AND USE ROSEN ENTERTAINMENT SYSTEMS OVERHEAD VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY TO BE VIEWED BY REAR-SEAT OCCUPANTS. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO VIOLATE STATE LAW. ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE. Rosen A7 Installation Guide 1

2 1 Make sure you have the components and tools you ll need MAKE SURE YOU HAVE ALL THE NEEDED COMPONENTS Before you begin to disassemble the vehicle, make sure you have all the appropriate kit contents. Determine which optional components are to be installed, if any. Standard Components: Model # RES Part #! A7 overhead console in Neutral or Gray AC3100 Neutral AC3101 Gray ! Flush-Mount Trim Ring in Neutral or Gray AC3106 Neutral AC3107 Gray ! Mounting bracket AC ! Hardware pack AC ! FM Modulator AC ! Harnesses and cables: *(if used in the installation) Black power harness AC Blue FM Modulator harness AC Green Auxiliary input cable* AC Yellow Video Out cable * AC Four-wire Domelight Harness AC ! Remote Control AC ! Two (2) Infrared Wireless Headphones AC ! Owner s Manual AC Optional Components:! CV4000 TV Tuner kit ( AC3105 TV Tuner, AC3024 harness, AC3035 TV antenna)! R5000-series VCP and optional harness AC3024 (not included with VCR)! AC3002 TV Antenna (if installing an R5000-series VCR with TV tuner).! CV7000 Second Screen Kit (AC monitor, CV2008 shroud, AC3193 cable) Note: This monitor installs differently than the A7 - see the included manual MAKE SURE YOU HAVE THE TOOLS AND PARTS YOU LL NEED These common hand tools are needed in almost every installation:! Phillips #2 screwdriver! Knife and blades! Digital multimeter (DMM)! Wire cutters, strippers,and a crimping tool! Panel-removing tools! Marking pen or chalk, and cleaning cloths 1/4 drive sockets are often needed for dashboard and trim disassembly. 3/8 drive sockets are often needed for seat removal and reinstallation. Check if Torx or Allen-drive bolts are used on any panels you will be removing,or if special tools are needed to remove the radio. You will need a DVD and a CD in good condition when testing the system. Standard installation parts you will need include wire, wire ties, wire crimp connectors or solder, and electrical insulating tape. Installation of aftermarket automotive electronics also often requires access to special parts such as antenna adapters. It is a good idea to have a source for these common installation parts. Rosen A7 Installation Guide 2

3 2 Check out the vehicle and plan your work IMPORTANT! The vehicle s roof beam (above the headliner) must support the! weight of the overhead console. The supplied mounting bracket must be firmly attached to the roof beam. Determine if this is possible to ensure that the vehicle is suitable for an A7 installation. CHECK THE BATTERY Test the battery voltage and inspect battery terminals for tightness and any corrosion. This takes 30 seconds and can save hours of troubleshooting later. DECIDE ON A LOCATION FOR THE A7 Location of the A7 varies by vehicle, but is typically on the center line of the vehicle and is always aft of the front seats. Often, the A7 s domelights replace the factory dome light. Always attach the mounting bracket to the existing roof cross beams. NOTICE OF INTENDED INSTALLATION AND USE ROSEN ENTERTAINMENT SYSTEMS OVERHEAD VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY TO BE VIEWED BY REAR-SEAT OCCUPANTS. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO VIOLATE STATE LAW. ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE. The A7 requires adequate roof support and a relatively flat headliner. Before you begin installation, drop the dome light and partially drop the headliner, and verify that you have sufficient clearance and sufficient support from a roof beam. Inspect the vehicle roof and headliner area and consider the following questions.! Does the vehicle have overhead climate controls? Does their location interfere with installation of the A7?! Is the dome light located where it would interfere with your installation of the A7? The A7 has built-in dome lights which connect to the existing vehicle domelight wiring, so the A7 can replace the factory dome light.! Does the vehicle headliner contour require using the optional AC3062 A7 Universal Tall Trim RIng and modifying it? (Make sure you have the tools needed). CHECK OUT THE VEHICLE RADIO The FM modulator usually must be located behind the vehicle radio, since it connects to the radio antenna cable. Remove the radio first to determine the type of antenna connector it uses. Some antennas require optional adapters - make sure you have them, if needed!! IMPORTANT! Before you disconnect the vehicle radio, make sure that you have the security code, if the radio uses a code! Check the vehicle owner's manual for details. Rosen A7 Installation Guide 3

4 Do Not Remove Warranty will be VOID If this label is removed or tampered with See Documentation for Liability Limitations All Rights Reserved. Covered under one or more of the following US Patents: 5,946,055 6,124,902 6,157,418 6,115,086 6,246,449 6, ,292,236 6,059,255 6,529,123 6,412,848 6,364,390 Design 456,789 and others pending 3 Cut the headliner and mount the bracket! IMPORTANT! DO NOT BEGIN THIS STEP UNTIL YOU HAVE INSPECTED THE HEAD- LINER, THE ROOF BEAM, AND ALL OTHER ESSENTIAL AREAS, AND VERIFIED THAT THE INSTALLATION CAN BE SUCCESSFULLY COM- PLETED! IT IS YOUR RESPONSIBILITY TO MAKE SURE THE INSTAL- LATION IS SAFE, SECURE, AND APPROPRIATE TO THE VEHICLE. STEP 1: SELECT A MOUNTING METHOD! Standard mounting. You will need to cut the headliner in order to create a path for the cables and to mount the bracket. Sometimes slight modifications to the included trim ring are needed. The bracket will mount laterally and the A7 mounting screws must be able to line up with the threaded on the bracket as shown. Vehicle Roof Bracket Cable Exit Roof Beam Cables Headliner Trim Ring Bracket oriented laterally for Mounting Screws A7 DVD Entertainment System FMM Power TV Tuner AUX VCP / Changer Screen 2 Connectors for Mounting Screws Driver s side mounting holes Passenger side mounting holes (Continued) Rosen A7 Installation Guide 4

5 ! Standard mounting with a spacer. This is the same as Standard mounting except that optional spacers are inserted between the Bracket and the beam to allow extra room. Vehicle Roof Bracket Optional Spacer(s) Cable Exit Roof Beam Cables Headliner Trim Ring Bracket oriented laterally! Custom mounting. This involves modifying the bracket or using appropriate brackets, and can also involve using an AC3062 A7 Universal Tall Trim Ring, and modifying it to fit the vehicle. As with every installation, it is your responsibility to make the installation safe, secure, and appropriate to the vehicle. RES does not recommend recessed mounting (without a trim ring) due to possible high-temperature operation issues. Vehicle Roof Roof Beam Bracket (Bent) Cable Exit Roof Beam Cables Headliner Optional Tall Trim Ring (AC3062) Bracket oriented lengthways Rosen A7 Installation Guide 5

6 STEP 2: CUT THE HEADLINER 1 Use the included paper template. Center the template on the center line of the vehicle by measuring the width of the headliner, dividing by two, and making a chalk mark on the center line. FRONT of Vehicle Cable Exit Paper template Always double-check to make sure the template is correctly oriented front-to-rear. Be careful not to remove more headliner material than absolutely neccessary, especially if there is a domelight opening within the A7 footprint. Trim Ring Footprint DVD drive Mounting screw paths! IMPORTANT! If you cut away too much of the headliner, you will create a direct path for heat to radiate from the roof of the vehicle into the DVD drive. On very hot days, this type of installation could trigger the A7 temperature protection (the A7 DVD drive shuts down above 140 O F). To minimize heat exposure, only cut the headliner where absolutely needed - see below. Vehicle Roof Bracket Optional Spacer(s) Cable Exit Roof Beam Cables Headliner Headliner between DVD drive and roof cavity Trim Ring 2 Double-check the template s front/rear orientation and position. If you position the template backwards, the cable exit hole you cut will not be covered by the A7! 3 Trace the template outline onto the headliner with a pencil, marker, or chalk. 4 Using a sharp blade, carefully cut out the headliner. Cut on the inside of your line. 5 Test-fit the A7 into the headliner opening. You may need to carefully trim in the corners of your opening. Rosen A7 Installation Guide 6

7 STEP 3: MOUNT THE BRACKET! CAUTION! Make sure that the screws you use to mount the bracket and the A7 are not too long! If the screws you select are too long, you will damage the roof of the vehicle. Take great care when planning this part of your installation. Optional Spacers may be needed With some vehicle roof beams, you may need to use optional spacers to mount the bracket to the beam. Some thick headliners require spacers between the bracket and the A7. If test-fitting indicates that you need to use the included spacers between the A7 and the bracket, pre-insert each mounting screw into the A7 from below as shown. Then press the spacer over the tip of the screw. The spacers should hold the screws in place. Insert mounting screw After you have pre-inserted all four screws, go to the next step - do not mount the A7 yet! Stand Vehicle Roof Bracket Optional Spacer(s) (not included) Cable Exit Roof Beam Cables Headliner Bracket oriented laterally Optional Spacers (included in hardware kit) Trim Ring Bending or modifying the Bracket The bracket is designed to be able to be bent or shortened as needed. Bend/break lines Bend/break lines Rosen A7 Installation Guide 7

8 Do Not Remove Warranty will be VOID If this label is removed or tampered with See Documentation for Liability Limitations All Rights Reserved. Covered under one or more of the following US Patents: 5,946,055 6,124,902 6,157,418 6,115,086 6,246,449 6, ,292,236 6,059,255 6,529,123 6,412,848 6,364,390 Design 456,789 and others pending MOUNT THE BRACKET (continued) Remove the headliner trim and any grab handles over the rear door frame. Slide the bracket in between the headliner and the roof. Mount the bracket to the roof beam through the opening you made in the headliner. A minimum of four short screws must be used to mount the bracket. Bend/break lines CAUTION! Slots for screws or optional AC3024 stabilizing mounting feet Lateral Bracket Positioning for Mounting Screws A7 DVD Entertainment System FMM Power TV Tuner AUX VCP / Changer Screen 2 Connectors for Mounting Screws Long-axis Bracket Positioning for Mounting Screws for Mounting Screws Do Not Remove Warranty will be VOID If this label is removed or tampered with See Documentation for Liability Limitations FMM A7 DVD Entertainment System All Rights Reserved. Covered under one or more of the following US Patents: 5,946,055 6,124,902 6,157,418 6,115,086 6,246,449 6, ,292,236 6,059,255 6,529,123 6,412,848 6,364,390 Design 456,789 and others pending Power TV Tuner AUX VCP / Changer Screen 2 Connectors Bend or break Bracket at this point to create a cable exit! (See Pages 5, 7) Rosen A7 Installation Guide 8

9 4 Route the harnesses and make all wiring connections For more information, see the system wiring diagram on page 14. INSTALLATION PRECAUTIONS Use caution to assure that harnesses and cables are protected from sharp edges. Where necessary, add tape to cover sharp surfaces. Avoid routing harnesses and cables with sharp bends (always less than 90 O, but less than 45 O is preferred), or where there is the potential for pinching or other damage. The locking connectors in this system require that even force be applied to the release latch when harnesses are disconnected. Failure to use reasonable care will damage the connector and cause system failure. CABLE AND HARNESS ROUTING 1 Starting at the headliner cutout, route the black power harness and the blue FMM cable to the underdash area. Leave about six inches of cable hanging through the cutout. Allow enough slack in the harnesses above the headliner to allow working room. You may want to leave a short loop hanging out the side of the headliner until final reassembly (this makes stuffing cables into the headliner easier when you mount the A7). 2 You may want to secure the cables with tape so they lie flat. This makes it easier to reassemble the vehicle trim correctly, especially with sunroof vehicles. 3 If the Auxiliary Input harness or any other optional harnesses are being used, route them from the headliner cutout to their destination. Remember to leave working slack. When using optional harnesses, you may need to split the harness paths, routing some harnesses down one side of the vehicle and the rest down the other. CONNECTING THE POWER HARNESS The A7 requires both constant 12V (+) and switched 12V (+) energized when the key is in the Accessory position. These can be found at the ignition switch harness. The A7 ground wire should mount to bare metal, using a factory ground bolt whenever possible. Power Harness Connections: Yellow 12V (+) Constant Power (Fused 7.5 A) Red 12V(+) Switched Accessory (Fused 1 A) Black Chassis (-) Ground Blue 12V(+) output when FM Modulator is on (not used in most installations)! IMPORTANT: - Grounding the Blue power harness wire will cause system failure. - Connecting the Red wire to constant 12V(+) causes battery drain and premature battery failure. CONNECTING THE FM MODULATOR HARNESS FM Modulator Connections: Gray 12V(+) FMM Control On/Off Connect to Red of FM Modulator Black/White FMM Ground Connect to Black of FM Modulator Blue/White, Brown Not used - cap off to avoid shorting to ground Red, White RCAs Red and White input RCAs on FM Modulator Rosen A7 Installation Guide 9

10 Connecting the Domelight Harness The A7 has a domelight harness which connects to the vehicle domelight wiring. Remove the vehicle domelight, find the vehicle domelight harness connector, and unplug it. Use a digital multimeter to test all the wires in the vehicle domelight connector, to determine which of the following domelight wiring systems is being used. Notes: Many vehicles have domelight delay timers which keep the lights on for a few seconds after the doors are closed, or which shut off the domelight after it has been on for too long. Make sure these timers don t defeat your testing - occasionally turn the ignition key on and off, and open and close all the doors. The wire color and operation at the domelight is not always the same as the wiring in the kick panel - alarm wiring information is often not accurate for these connections. Always determine how the wires work at the domelight, not at the kick panel! Negative door trigger systems have the following wires: Constant 12V(+). Negative door trigger. This will test as switched (-) ground when the doors are open, and either 12V(+) or an open circuit when the doors are closed. Constant ground. Note: This wire may not be present if the dome light grounds through its mounting screws, or if it does not have an on/off switch built in. Positive door trigger systems (many Ford and GM) have the following wires: Constant Ground. Note: This wire may not be present if the domelight grounds through its mounting screws. Positive door trigger. This will test as switched 12V(+) when the doors are open, and either (-) ground or an open circuit when the doors are closed. Constant 12V(+). Note: This wire may not be present if the dome light does not have an on/off switch built in. (In new GM cars, Rosen recommends not using this orange wire - connect to another source of 12V constant). Domelight Harness Connections: Yellow wire to 12V(+) constant voltage (Note: in newer positive- trigger GM cars, do not use the GM 12V constant orange wire - connect to another source of 12V constant). Black wire to vehicle chassis (-) ground. Green wire to the vehicle (-) door trigger wire, or Purple wire to the (+) door trigger wire. Note: If the Green wire is unused, you must cap it off to prevent it shorting to ground! Note: The A7 Domelight has a built-in timer that limits the domelight to around five minutes of illumination. This is to prevent accidental battery drain. To turn the domelight back on after the timer has turned it off, just press the domelight button again. Rosen A7 Installation Guide 10

11 Do Not Remove Warranty will be VOID If this label is removed or tampered with See Documentation for Liability Limitations All Rights Reserved. Covered under one or more of the following US Patents: 5,946,055 6,124,902 6,157,418 6,115,086 6,246,449 6, ,292,236 6,059,255 6,529,123 6,412,848 6,364,390 Design 456,789 and others pending 5 Install the A7 and the FM Modulator 1 Test-fit the A7 and the trim ring to determine if the trim ring or headliner should be trimmed. Optimally, the top of the trim ring will be in complete contact with the roof beam, without any gaps achieving this may require trimming the edges of the trim ring (if there are gaps, the domelights may backlight them and make them more noticeable). You can also insert foam above the headliner to help seal gaps from above. Some thicker headliners may require the use of the included spacers - see Page 7 for details. 2 Plug in all the harnesses and cables that you are using, following the color-coded label on the top (remember the domelight harness). The video output and auxiliary harnesses aren t used in all installations. Connectors Label A7 DVD Entertainment System FMM Power TV Tuner AUX VCP / Changer Screen 2 3 Mount the A7 to the bracket with four machine screws of a safe length. Four 45mm-long machine screws are included - use only if they are appropriate for your installation. Some thicker headliners may require the use of the included spacers - see Page 7 for details and more information. CAUTION!!! Make sure that the screws you use to mount the A7 are not too long! If the screws you select are too long, you will damage the vehicle roof. IMPORTANT! Do NOT overtighten! Check for proper deployment of the screen and proper ejection of discs if there is any binding, check for uneven screw torquing. Difficulty in ejecting discs means that the front screws are too tight. Binding indicates that the side edges of the trim ring need to be trimmed to relieve pressure on the sides of the A7. 4 Note the FM Modulator frequency switch setting - either 87.9FM or 88.3 FM. Unplug the radio s antenna cable - connect it to the FM Modulator. Connect the FM Modulator to the radio antenna port. Mount the FM Modulator, using wire ties as needed. Note: Do not re-assemble the vehicle yet! Rosen A7 Installation Guide 11

12 6 Test, reassemble, and basic re-test Remember - until you test your installation, you re not finished! Testing the system before you reassemble the vehicle can save you time troubleshooting any problems. Quick, basic testing after reassembling the vehicle assures that everything is ready to go for your customer. INITIAL SYSTEM AND INSTALLATION TEST 1 Reconnect the battery (if disconnected). 2 Make sure the vehicle can be started safely (for example, there are no tools or workers under the hood and you have appropriate exhaust ventilation). 3 Start the vehicle. 4 Tune radio to the FM Modulator frequency (either 87.9 FM or 88.3 FM). 5 Open the A7 monitor to power up system. 6 Insert the battery into the remote control, and a DVD into the slot. 7 Test TV Tuner or VCP sources if installed, and the Auxiliary Input source if in use. 8 Check both headphones for proper operation (after properly inserting the batteries). 9 Listen to both DVD and CD audio with the FM Modulator on (use the Speaker On/Off button on the remote or on the front of unit). If the DVD Audio level is too low or the CD Audio level is too high, adjust the FM Modulator until both are appropriate. 10 Test for Audio and Video noise with the engine running and the alternator loaded (headlights on high, rear defroster on). If noise is heard or seen:! Check your ground connection on the Power Harness Black wire and the FMM Black/White wire.! Check the battery voltage and the connection quality of the (+) and (-) terminals (these should already have been checked).! Separate the FM Modulator and Power harnesses as far as possible and retest. REASSEMBLE THE TRIM PANELS Carefully reassemble the vehicle. Make sure not to pinch, pierce, or damage any of the cables or harnesses. QUICKLY RETEST THE SYSTEM BASICS After you reassemble the vehicle, quickly retest the system for power-up, audio and video, and noise to verify that no cables or harnesses were disconnected or damaged during reassembly. DELIVER THE VEHICLE Congratulations! The vehicle is now ready for delivery. Rosen A7 Installation Guide 12

13 Frequently Asked Questions Why does the audio seem quiet or distorted? If this is happening with a DVD, retest with the RES Sound Processing feature turned on. This feature helps optimize DVD audio for car stereo systems. Check the disc for damage. If it is a CD-R, make sure the recording level wasn t too low or too high. Check the FMM level setting. Quiet audio can mean the setting is too low, and distorted audio can mean the setting is too high. When testing, use both CDs and DVDs - they often have different audio levels, and adjusting for only one can cause problems with the other. Why is there no audio coming from the DVD player? Make sure that the DVD s Setup Menu Digital Audio output setting is Off. Why are the domelights working backwards? The green or purple door-trigger input wire is connected to the wrong polarity trigger wire in the car. See the main wiring diagram on page 14. Can I use both a Rosen TV Tuner and a Rosen VCP in the same system? Yes - you ll use two optional AC3024 harnesses. However, many Rosen VCPs have onboard TV tuners. Why doesn t the optional VCP or TV Tuner work? Are you pressing the Power button on the A7 remote after selecting the TV Tuner or VCP as a source? (The A7 Power button only controls them when they are the selected source). Is the IR mini-jack plugged from the Magenta harness plugged in to the unit? Is the Blue wire of the VCP connected to the Blue wire of the Magenta VCP harness? Connect both the Red and Blue of the VCP to the Red of the harness. How can I add an additional screen? The CV7200 kit has a matching 7 widescreen display with a special cable included (AC3193) that makes installation and operation with an A7 simple and straightforward (Note: This monitor installs differently than the A7 - see the included manual). The included video output cable can be used to add any monitors with a composite RCA video input. RES recommends grounding any added monitors to the same point as the A7. The screen does not fully deploy, or discs do not eject - what do I do? Check the screw torque. Refer to page 11 for tips. The system keeps shutting off while I try to test it. Why? This could be a low-voltage problem - check the battery. Check power and ground connections. This is a symptom of poor electrical connections. Make sure you are not using a damaged DVD disc. Call Rosen Technical Support to determine if any of the internal protection modes are being triggered - (888) Rosen A7 Installation Guide 13

14 Do Not Remove Warranty will be VOID If this label is removed or tampered with See Documentation for Liability Limitations All Rights Reserved. Covered under one or more of the following US Patents: 5,946,055 6,124,902 6,157,418 6,115,086 6,246,449 6, ,292,236 6,059,255 6,529,123 6,412,848 6,364,390 Design 456,789 and others pending Rosen A7 Installation Guide 14 Rosen A7 System Wiring Diagram FM frequencies: 87.9 or 88.3 Level adjustment screw on bottom of unit AC 3195 FMM Blue FMM Cable (AC3191) To Radio and Antenna Red of FMM to Gray of A7 Black of FMM to Black/White of A7 Blue/White, FMM Harness - Do not use Brown, FMM Harness - Do not use RCA connections FMM Front of Unit (Disc Slot) A7 DVD Entertainment System Power TV Tuner AUX VCP / Changer Screen 2 Domelight Harness (AC 3063) Yellow: 12V(+) Constant Black: (-) Ground Gray: (-) Negative door input Purple: (+) Positive door input * Wiring Connections, Green Optional Magenta *Optional Auxiliary TV Tuner/VCP Harness AC3024: Magenta Input Cable Red 12V(+) Output - Connect to Red of TV Tuner, or Cable,TV Tuner (AC 3198) Connect to Red and Blue of VCP (AC 3024) Blue Cap off - do not use Black (-) Ground Lead of Source Black Power Cable/ Harness (AC 3197) A7 connector map This color-coded label is on the top of the A7. Plug in cables and harnesses as shown. A7 DVD Entertainment System FMM POWER TV TUNER AUX VCP SCREEN 2 Note: Black cables are required, Gray cables are optional. (The Green and Yellow cables are included, but not required) Yellow Video Output Cable (AC 3192) (Note: When using a second screen, this is replaced by the AC3193 cable, included with the CV7200 second-screen kit) *Optional Magenta Cable, VCP (AC3024) Black (-) Chassis Ground Red 12V(+) Switched Accessory Yellow 12V(+) Constant Blue 12V(+) Controlled Output Important: Do not allow the Blue wire to short to ground - system damage will result.

INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System

INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE CAR SHOW VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY

More information

INSTALLATION GUIDE AV7900 Dual Multimedia Headrest Replacement System

INSTALLATION GUIDE AV7900 Dual Multimedia Headrest Replacement System INSTALLATION GUIDE AV7900 Dual Multimedia Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE AV7900 VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY

More information

INSTALLATION GUIDE. AV8900H Dual Multimedia Headrest Replacement System

INSTALLATION GUIDE. AV8900H Dual Multimedia Headrest Replacement System INSTALLATION GUIDE AV8900H Dual Multimedia Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE AV8900H VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED

More information

INSTALLATION GUIDE AV7000 Dual DVD Headrest Replacement System

INSTALLATION GUIDE AV7000 Dual DVD Headrest Replacement System INSTALLATION GUIDE AV7000 Dual DVD Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE ROSEN ENTERTAINMENT SYSTEMS VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO

More information

For additional technical tips, please visit

For additional technical tips, please visit NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE

More information

For additional technical tips, please visit

For additional technical tips, please visit NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE

More information

Conflicts: Vehicles with no sunroof or dual sunroof

Conflicts: Vehicles with no sunroof or dual sunroof Toyota Sienna (Single Sunroof) 2012-8.5 Overhead Video Part Number: 00016-00125 -11 Accessory Code: ED9 Conflicts: Vehicles with no sunroof or dual sunroof General Applicability: 2011 Sienna SMR Kit Contents:

More information

VOH681A Drop Down Video Monitor VOH682A Drop Down TV / Video Monitor OPEN. Installation Guide

VOH681A Drop Down Video Monitor VOH682A Drop Down TV / Video Monitor OPEN. Installation Guide VOH681A Drop Down Video Monitor VOH682A Drop Down TV / Video Monitor ON OFF AUTO OPEN Installation Guide Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which

More information

Conflicts: Toyota Tundra CrewMax w/non Sunroof Overhead Video. Part Number: Accessory Code: ED80.

Conflicts: Toyota Tundra CrewMax w/non Sunroof Overhead Video. Part Number: Accessory Code: ED80. Toyota Tundra CrewMax w/non Sunroof 2011-8.5 Overhead Video Part Number: 00016-00125-07 Accessory Code: ED80 Conflicts: 1.) Third Passenger Front Seating 2.) Sunroof General Applicability: Non Sunroof

More information

Conflicts: Highlander without sunroof

Conflicts: Highlander without sunroof Toyota Highlander (Sunroof) 2011-8.5 Overhead Video Part Number: 00016-00125; Fit Kit-00016-00125-02 Accessory Code: ED9 Conflicts: Highlander without sunroof Kit Contents: Item # Qty. Component Description

More information

VDS102T DROP-DOWN VIDEO MONTOR

VDS102T DROP-DOWN VIDEO MONTOR VDS102T DROP-DOWN VIDEO MONTOR ON OFF AUTO Installation Guide Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video

More information

Toyota 4RUNNER With/MR Overhead Video

Toyota 4RUNNER With/MR Overhead Video Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:

More information

Conflicts: Vehicles with a sunroof

Conflicts: Vehicles with a sunroof Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:

More information

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles

More information

If technical support is required, please contact Advent Technical Support at

If technical support is required, please contact Advent Technical Support at Document 128-9015A Created 12/12/11 Kit Contents: Item # Qty. Component Description 1 2 Headrest Assembly 2 2 Cables # 3 3 1 Power Cord # 9 4 1 FM Antenna 5 1 Control Box 6 2 IR Headphones 7 2 Remote Control

More information

ADVDLX10 A 10.1 OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER INSTALLATION GUIDE

ADVDLX10 A 10.1 OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER INSTALLATION GUIDE ADVDLX10 A 10.1 OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER R INSTALLATION GUIDE TABLE OF CONTENTS IMPORTANT NOTICES...2 GENERAL SYSTEM CONFIGURATIONS (IR TRANSMIT AND RECEIVE MODES M1 OR M2)...3

More information

Toyota Prius Dual Player Headrest Video ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF 01/17/2011

Toyota Prius Dual Player Headrest Video ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF 01/17/2011 Toyota Prius 2011 - Dual Player Headrest Video Part Number: 00016-47210-01; 04; 11 Code : EH5 ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF 01/17/2011 Conflicts Kit Contents

More information

ADVEXL12A 12.1" OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER AND HD INPUTS INSTALLATION GUIDE

ADVEXL12A 12.1 OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER AND HD INPUTS INSTALLATION GUIDE ADVEXL12A 12.1" OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER AND HD INPUTS R INSTALLATION GUIDE TABLE OF CONTENTS Important Notices...2 General system configurations (IR Transmit and Receive Modes

More information

KD-DV7206/KD-DV7205 Installation/Connection Manual

KD-DV7206/KD-DV7205 Installation/Connection Manual GET0375-006A [U/UT] KD-DV7206/KD-DV7205 Installation/Connection Manual 0106DTSMDTJEIN EN, CT 2006 Victor Company of Japan, Limited ENGLISH This unit is designed to operate on 12 V DC, NEGATIVE ground electrical

More information

ADVEXL10 A 10.1" OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER PUSH INSTALLATION GUIDE

ADVEXL10 A 10.1 OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER PUSH INSTALLATION GUIDE ADVEXL10 A 10.1" OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER R S PUSH INSTALLATION GUIDE TABLE OF CONTENTS IMPORTANT NOTICES...2 GENERAL SYSTEM CONFIGURATIONS (IR TRANSMIT AND RECEIVE MODES M1 OR

More information

PK-SIEN11 Toyota Sienna Piranha System

PK-SIEN11 Toyota Sienna Piranha System Toyota Sienna Installation Guide NOTICE OF INTENDED INSTALLATION AND USE PK-SIEN11 Toyota Sienna Piranha System THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS NOT INTENDED

More information

TOYOTA LAND CRUISER 2003 DVD VES

TOYOTA LAND CRUISER 2003 DVD VES LEXUS LX470 Section I Installation Preparation Part Number: PT296 6002D 03/16 (LC) PT296 6002L 03/16 (LX) Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 FPD Assembly

More information

* Premium Audio equipped vehicles will require additional part # DP-HD0822P audio interface NOTICE OF INTENDED INSTALLATION AND USE

* Premium Audio equipped vehicles will require additional part # DP-HD0822P audio interface NOTICE OF INTENDED INSTALLATION AND USE * Premium Audio equipped vehicles will require additional part # DP-HD0822P audio interface NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER,

More information

(1) Remote Control with (2) AAA Batteries

(1) Remote Control with (2) AAA Batteries TOOLS REQUIRED: KIT CONTENTS: E14 Torx (1) Remote Control with (2) AAA Batteries (2) Wireless Headphones with (4) AAA Batteries (2) DVD Headrest Units Owner s Manual (1) Owner s Manual (1) Power / Audio

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: DUAL DVD HEADRESTRAINT MONITOR Pathfinder - (204 Above S grade, without factory FES, and VINs ending in less than 650298)

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: DUAL DVD HEADRESTRAINT MONITOR Pathfinder - (204 Above S grade, without factory FES, and VINs ending in less than 650298)

More information

Chevy Equinox / GMC Terrain 2013-up (with color display) G

Chevy Equinox / GMC Terrain 2013-up (with color display) G INSTALLATION INSTRUCTIONS FOR PART 99-3308G Chevy Equinox / GMC Terrain 2013-up (with color display) 99-3308G KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted gray to match

More information

SCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT

SCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2004 TSX BII 24811 Issue Date APRIL 2003 PARTS LIST Attachment Kit P/N 08B23-SDA-101A Monitor bracket harness FM

More information

PRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B. Display bracket.

PRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B. Display bracket. INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2006 PILOT All 30502 Issue Date SEP 2005 PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B Display

More information

TOYOTA im INTERIOR LIGHT KIT Preparation

TOYOTA im INTERIOR LIGHT KIT Preparation Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1

More information

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts!

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts! 2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit

More information

* JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface NOTICE OF INTENDED INSTALLATION AND USE

* JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface NOTICE OF INTENDED INSTALLATION AND USE * JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER,

More information

* JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface NOTICE OF INTENDED INSTALLATION AND USE

* JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface NOTICE OF INTENDED INSTALLATION AND USE * JBL Audio equipped vehicles will require additional part # DP-TYJBL1 audio interface NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER,

More information

Mobile Video Installation Guide

Mobile Video Installation Guide 000MVGUIDE Revision 04/29/04 Mobile Video Installation Guide This installation guide offers examples of mobile video system types and suggested layouts. The installation of your system will depend upon

More information

1. Check the contents of the installation kit

1. Check the contents of the installation kit DC3 Video Event Recorder Standard Installation Instructions Installation of the event recorder is not complicated, but care must be taken to ensure successful operation. Follow these instructions carefully

More information

Nissan Maxima (with Technology Package) Nissan Maxima (with NAV) 2009 KIT FEATURES. ISO DIN radio provision with pocket...

Nissan Maxima (with Technology Package) Nissan Maxima (with NAV) 2009 KIT FEATURES. ISO DIN radio provision with pocket... 99-7633 INSTALLATION INSTRUCTIONS KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted high gloss black KIT COMPONENTS A) Radio trim panel with climate controls B) Radio brackets

More information

Performance Oil Cooler Kit for (C6) Chevrolet Corvette

Performance Oil Cooler Kit for (C6) Chevrolet Corvette Performance Oil Cooler Kit for 2005-2013 (C6) Chevrolet Corvette Part No. EC6-600 Made in USA Important: Read these instructions in their entirety prior to installation. Copyright 2008-2018 Improved Racing

More information

AXi-MBCIRC-R INSTALLATION MANUAL

AXi-MBCIRC-R INSTALLATION MANUAL Rev. 4.0 081915 AXi-MBCIRC-R INSTALLATION MANUAL PLEASE REVIEW THIS INSTALLATION MANUAL CAREFULLY BEFORE BEGINNING ANY WORK PLUG & PLAY WIRING HARNESS COMPATIBLE WITH AXi-RGB2 AXi-RGB3 Tech Support: 844-AXX-ESSI

More information

SCION tc Navigation System Preparation. Part Number: PT

SCION tc Navigation System Preparation. Part Number: PT Preparation Part Number: PT611-21111 Kit Contents Item # Quantity Reqd. Description 1 1 Navigation System 2 1 GPS Antenna 3 1 Bluetooth Antenna 4 1 Wire Harness (Reverse / Park Brake) 5 1 RCA Relay Cable

More information

2015+ F-150 Active Exhaust Kit Installation Instructions P/N: (1117-5E292LITE)

2015+ F-150 Active Exhaust Kit Installation Instructions P/N: (1117-5E292LITE) 2015+ F-150 Active Exhaust Kit Installation Instructions P/N: 422104 (1117-5E292LITE) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Ford F-150 Active Exhaust Kit Installation Instructions

More information

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION

More information

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable

More information

IMPORTANT. Tools Needed: (depending upon vehicle) Phillips Screwdriver. Drill & Bit Set. Wire Stripper/ Crimp Tool

IMPORTANT. Tools Needed: (depending upon vehicle) Phillips Screwdriver. Drill & Bit Set. Wire Stripper/ Crimp Tool Revision 3/14/05 Amplifier Installation Guide IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call:

More information

AXi-GM2-R INSTALLATION MANUAL

AXi-GM2-R INSTALLATION MANUAL Rev. 4.0 081915 AXi-GM2-R INSTALLATION MANUAL PLEASE REVIEW THIS INSTALLATION MANUAL PLUG & PLAY WIRING HARNESS COMPATIBLE WITH AXi-RGB1 AXi-RGB2 AXi-RGB3 Tech Support: 844-AXX-ESSI WWW.AXXESSINTERFACES.COM

More information

Gentex by VOXX Corporation Installation Instructions

Gentex by VOXX Corporation Installation Instructions KIT CONTENTS: Item Qty Part Number Description 1 1: ADVGEN20A 7 Pin Auto-Dimming Mirror with Compass and Temperature 2 1 Gentex by VOXX Corporation Installation Instructions Contact VOXX Customer Service

More information

GM TRUCK BACKUP CAMERA INSTALLATION

GM TRUCK BACKUP CAMERA INSTALLATION GM TRUCK 07-13 BACKUP CAMERA INSTALLATION Thank you for your purchase! These instructions are intended for the do-it-yourselfer who decides to install the camera without professional assistance. Keep in

More information

INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE

INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE LAST UPDATED: April 2018 Thank you for choosing the Motor Trike Electric Reverse. We ask that you read the directions before you start and follow

More information

INSTALLATION INSTRUCTIONS FORD POWERSTROKE PICKUPS MODEL YEAR

INSTALLATION INSTRUCTIONS FORD POWERSTROKE PICKUPS MODEL YEAR p p INSTALLATION INSTRUCTIONS FORD POWERSTROKE PICKUPS MODEL YEAR 2005-2006 www.dieselturbolifesaver.com Diesel Turbo Lifesaver (DTLS) is a computer controlled device that allows you to set an automatic

More information

U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M

U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof

More information

Installation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)

Installation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf) Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well

More information

IT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.

IT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR. Instructions for Universal Harness PRINT THESE INSTUCTIONS Gentex Mirror Installation Instructions Provided by www.rearviewautomirrors.com These instructions have been prepared to provide you with details

More information

DASH AUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev 01 04/16 Page 1 of 6. Verify accessory fitment at Polaris.com.

DASH AUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev 01 04/16 Page 1 of 6. Verify accessory fitment at Polaris.com. DASH AUDIO KIT P/N 2882030 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these

More information

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Procharger Stage II Intercooled Supercharger System (11-14 GT) Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2

More information

Light Truck MegaShifter

Light Truck MegaShifter Installation Instructions Light Truck MegaShifter The B&M Light Truck Megashifter shifter is designed to be used in most light trucks equipped with most popular three speed or four speed automatic transmissions.

More information

Jeep Cherokee Latitude/Limited 2014-up

Jeep Cherokee Latitude/Limited 2014-up Installation instructions for part 99-6526 REV. 5/23/2017 INST99-6526 KIT FEATURES ISO DDIN radio provision Included interface shows climate and menu info on the aftermarket radio screen. Painted scratch-resistant

More information

Nissan Pathfinder (without NAV) (with color screen) HG

Nissan Pathfinder (without NAV) (with color screen) HG Installation instructions for part 99-7627HG Nissan Pathfinder 2013-2016 (without NAV) (with color screen) 99-7627HG KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted to

More information

TOYOTA TACOMA EC REARVIEW MIRROR Preparation

TOYOTA TACOMA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,

More information

SCION tc 2014 FOG LIGHT KIT

SCION tc 2014 FOG LIGHT KIT Part #: PT413-21140 Conflicts: P/N PTR11-21100 Lowering Springs (CA only) Kit Contents: Wire Ties Self-Tapping Screws Switch Relay Fog Light Bezel, Left and Right Side Wire Harness Fog Lamp, Left and Right

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual John Deere MFWD AutoTrac Ready Supported Models 8225R 8245R 8270R 8295R 8320R 8345R PN: 602-0254-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in

More information

Gentex by VOXX Corporation Installation Instructions

Gentex by VOXX Corporation Installation Instructions Gentex by VOXX Corporation Installation Instructions Bezelled ADVGEN45A4 Bezelled w/ Homelink ADVGEN80EXP ADVGEN45A4PW4 ADVGEN40A4 Frameless ADVGEN8EXP Frameless w/ Homelink ADVGEN85EXP ADVGEN45AB5 TOOLS

More information

TOYOTA TACOMA XM SATELLITE RADIO Preparation

TOYOTA TACOMA XM SATELLITE RADIO Preparation Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness

More information

Conflicts. TOYOTA 4Runner REARSIGHT. Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS

Conflicts. TOYOTA 4Runner REARSIGHT. Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS TOYOTA 4Runner 2010 - REARSIGHT Part Number: 00016-00085 Code: MC90 Conflicts KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS 5

More information

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:

More information

Kit Contents. Color Applicability/Trim Level. Hardware Bag Contents. General Applicability. Recommended Sequence of Application

Kit Contents. Color Applicability/Trim Level. Hardware Bag Contents. General Applicability. Recommended Sequence of Application Document # 2646 Created 9/1/04 TOYOTA SCION XB 2005 - OVERHEAD VIDEO(AUTOCINEMA) Part Number: 00016-00420-09 Accessory Code: YH8 Kit Contents Item # Quantity Reqd. Description 1 1 MONITOR ASSEMBLY 2 1

More information

Installation Instructions Right Hand Drive Megashifter

Installation Instructions Right Hand Drive Megashifter Installation Instructions Right Hand Drive Megashifter Part Number 80685 1995, 2001, 2006, 2010 by B&M Racing & Performance Products The B&M Right Hand Drive Megashifter is designed specifically for vehicles

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 28 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY 2-5 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This

More information

INSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mazda For Models With Manual Climate Controls TOOLS REQUIRED:

INSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mazda For Models With Manual Climate Controls TOOLS REQUIRED: INSTALLATION INSTRUCTIONS FOR PART 99-7509 APPLICATIONS Mazda 5 2006-2007 For Models With Manual Climate Controls 99-7509 KIT FEATURES Painted To Match Factory Dash DIN Radio Provision with Pocket ISO

More information

TOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT

TOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,

More information

Main Harness Quantity: 1

Main Harness Quantity: 1 Smart Engine Start INSTALLATION MANUAL Genuine Part # : H001SVA900 Vehicle Model : WRX Kit Contents Service P/N: H001SVA910 Service P/N: H001SVA820 NOT USED NOT USED SES ECU Quantity: 1 Double-sided tape

More information

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

TOYOTA CAMRY TVIP V2 (GBS WITH ADD ON)

TOYOTA CAMRY TVIP V2 (GBS WITH ADD ON) Preparation Part Number: 08586-3T930 Kit Contents Item # Quantity Reqd. Description 1 2 Wire Harness (One wire harness is only for RS3200+) 2 1 GBS ECU 3 1 GBS Mounting Bracket 4 1 Microphone Hardware

More information

CH. Ford Edge (with 4.2 screen)

CH. Ford Edge (with 4.2 screen) 99-5848CH INSTALLATION INSTRUCTIONS Ford Edge (with 4.2 screen) 2011-2014 KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Touchscreen display for climate and personalization features

More information

Upgrade Options. Installation Guide WARNING

Upgrade Options. Installation Guide WARNING Panasonic POWER BS G-CODE CY-V700U Panasonic XMD 000 L/C 44XXXXXX INTELLIGENT SYSTEM XM RADIO ID : XXXXXXXX Upgrade Options Installation Guide 5.-channel Surround System This unit has a built-in 4-channel

More information

Technical Support (707)

Technical Support (707) Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform

More information

CH. Ford Explorer (with 4.2 screen)

CH. Ford Explorer (with 4.2 screen) 99-5847CH INSTALLATION INSTRUCTIONS Ford Explorer (with 4.2 screen) 2011-2015 KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Touchscreen display for climate and personalization

More information

AXi-MBEIRC-R INSTALLATION MANUAL

AXi-MBEIRC-R INSTALLATION MANUAL Rev. 4.0 081915 AXi-MBEIRC-R INSTALLATION MANUAL PLEASE REVIEW THIS INSTALLATION MANUAL CAREFULLY BEFORE BEGINNING ANY WORK PLUG & PLAY WIRING HARNESS COMPATIBLE WITH AXi-RGB2 AXi-RGB3 Tech Support: 844-AXX-ESSI

More information

Technical Support (707)

Technical Support (707) Installation Instructions UNIMATIC SHIFTER Fits: GM, Powerglide, Ford and Chrysler Transmissions See Application Guide for Specific Vehicles Catalog # 80775 WORK SAFELY! For maximum safety, perform this

More information

REC-11+ REMOTE RECEIVER UNIT

REC-11+ REMOTE RECEIVER UNIT Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous

More information

TOYOTA PRIUS XM SATELLITE RADIO Preparation

TOYOTA PRIUS XM SATELLITE RADIO Preparation Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity

More information

Procedure. These guidelines can be found in the "Accessory Installation Practices" document.

Procedure. These guidelines can be found in the Accessory Installation Practices document. Toyota Tundra 207 LED Illumination Package Part Number: 0006-00069 (Interior and Exterior) Accessory Code: LL000 Conf licts V ehicles with Option Code BZ Color Applicability/Trim Level Kit Content 4 Puddle

More information

TOYOTA TACOMA TVIP V3 (RS3200) Section I - Installation Preparation

TOYOTA TACOMA TVIP V3 (RS3200) Section I - Installation Preparation Section I - Installation Preparation Part Number: 08586-04810 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4

More information

Ford C6 Automatic Trans Mount Shifter Installation Instructions

Ford C6 Automatic Trans Mount Shifter Installation Instructions Ford C6 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C6 Automatic Trans Mount Installation

More information

Ford C4 and C6 Floor Mount Automatic Transmission Shifter Installation Instructions

Ford C4 and C6 Floor Mount Automatic Transmission Shifter Installation Instructions Ford C4 and C6 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C4 and C6 Mount

More information

ADD-ON REMOTE STARTER TO AFTERMARKET SYSTEM

ADD-ON REMOTE STARTER TO AFTERMARKET SYSTEM MEGATRONIX RS 110 ADD-ON REMOTE STARTER TO AFTERMARKET SYSTEM Installation and Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. RS110 ADD-ON REMOTE CAR STARTER For Vehicles Equipped With Automatic Transmission

More information

AX-ADGM01. GM Data Interface 2006-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.

AX-ADGM01. GM Data Interface 2006-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications. AX-ADGM01 INSTALLATION INSTRUCTIONS INTERFACE FEATURES Provides accessory power (12-volt 10-amp) Maintains the retained accessory power (R.A.P.) feature Provides NAV outputs (parking brake, reverse, speed

More information

MY F150 CrewCab 1. Tools Required 10X. Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo

MY F150 CrewCab 1. Tools Required 10X. Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo 2013-2014MY F150 CrewCab 1 Tools Required A B C D E F G 4X H I J K 3X L 3X 2X 10X 2X Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo 2013-2014MY F150 CrewCab 2 Vehicles with selector lever in floor

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior

More information

TOYOTA SIENNA TRAILER WIRE HARNESS Preparation

TOYOTA SIENNA TRAILER WIRE HARNESS Preparation Preparation Part Number: PT791-08150 (non-se) PT791-08102 (SE only) Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Module Harness 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting

More information

B. Ford Fusion 2013-up* *Visit metraonline.com for up-to-date vehicle specific applications.

B. Ford Fusion 2013-up* *Visit metraonline.com for up-to-date vehicle specific applications. 99-5841B INSTALLATION INSTRUCTIONS Ford Fusion 2013-up* *Visit metraonline.com for up-to-date vehicle specific applications. KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Integrated

More information

Ram 1500/2500/ up (with 8 touchscreen) B

Ram 1500/2500/ up (with 8 touchscreen) B INSTALLATION INSTRUCTIONS FOR PART 99-6527B Ram 1500/2500/3500 2013-up (with 8 touchscreen) 99-6527B KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Touchscreen display for climate

More information

TOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation

TOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation Section I Installation Preparation Part Number: 08586 47840 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 3 1 ECU Mounting Bracket Hardware Bag

More information

TOYOTA HIGHLANDE R REARSIGHT Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS

TOYOTA HIGHLANDE R REARSIGHT Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS TOYOTA HIGHLANDE R 2009- REARSIGHT Part Number: 00016-00085 Code: MC90 KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS 5 1 OWNER

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2007-Current Jeep Wrangler 360º System for Factory Display Radios (Kit # AVMS-3701v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2007-Current Jeep Wrangler 360º System for Factory Display Radios (Kit # AVMS-3701) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior

More information

IR Temp Probe. Toyota Sienna Rear Sight. Part Number: Accessory Code:MC1

IR Temp Probe. Toyota Sienna Rear Sight. Part Number: Accessory Code:MC1 Toyota Sienna 200 - Rear Sight Part Number: 0006-00085 Accessory Code:MC Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 2 3 4 5 6 7 8 MIRROR/MONITOR REVERSE MINI-CAMERA

More information

AVH-2330NEX AVH-2300NEX AVH-1330NEX AVH-1300NEX

AVH-2330NEX AVH-2300NEX AVH-1330NEX AVH-1300NEX AVH-2330NEX AVH-2300NEX AVH-1330NEX AVH-1300NEX DVD RDS AV RECEIVER Installation Manual Connection Precautions Your new product and this manual Do not operate this product, any applications, or the rear

More information

SCION iq AUDIO Preparation

SCION iq AUDIO Preparation Preparation Part Number: PT546-00140 (Base Radio) Kit Contents Item # Quantity Reqd. Description 1 1 Receiver Assembly, Radio Unit 2 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description

More information