OVERVIEW: This bulletin aids in diagnosis and repair of automatic transmission fluid weepage.
|
|
|
- Ariel Benson
- 6 years ago
- Views:
Transcription
1 NUMBER: GROUP: REV. A Transmission DATE: May 7, 2005 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retreival system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of DaimlerChrysler Corporation. THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN , DATED JANUARY 14, 2005, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDES AN ADDITIONAL PART AND REVISED REPAIR PROCEDURES FOR 2004 SPRINTER VEHICLES. SUBJECT: Automatic Transmission Fluid (ATF) Weepage OVERVIEW: This bulletin aids in diagnosis and repair of automatic transmission fluid weepage. MODELS: 2005 (LX) 300/Magnum (VA) Sprinter 2005 (WK) Grand Cherokee (ZH) Crossfire Coupe/Crossfire Roadster NOTE: This bulletin applies to vehicles equipped with a NAG1 automatic transmission (sales code DGJ or DGU). SYMPTOM/CONDITION: Transmission fluid may be wicking in the right front corner of the transmission oil pan area. DIAGNOSIS: If the vehicle exhibits the Symptom/Condition, inspect the 13-pin connector plug guide bushing as a possible source of the transmission fluid weepage. If the weepage appears to be coming from above the transmission oil pan gasket, DO NOT REPLACE THE TRANSMISSION OIL PAN GASKET, perform the appropriate Repair Procedure. PARTS REQUIRED: Qty. Part No. Description AB O-Ring, Transmission AB O-Ring, Transmission (AR) AA Transmission Fluid Sprinter and Crossfire Coupe/Crossfire Roadster
2 REV. A -2- Qty. Part No. Description (AR) AA Transmission Fluid 300/Magnum and Grand Cherokee **AR (1) AA Plug, Adapter Sprinter Only** LX VEHICLE REPAIR PROCEDURE: 1. Disconnect and isolate the negative battery cable. 2. Raise the vehicle on a suitable hoist. 3. Disconnect the 13-pin connector plug by turning the bayonet lock of the connector guide bushing counter clockwise (Fig. 1). 4. Place a suitable drain pan under the connector guide bushing to catch transmission fluid that may drain during the next step. 5. Using a 7 mm socket, loosen the bronze bolt securing the connector guide bushing. The bronze bolt is located in the center of the connector guide bushing (Fig. 2). Fig. 1 CONTROL HARNESS CONNECTOR 1 - BAYONET LOCK OF THE CONNECTOR GUIDE BUSHING 2-13 PIN CONNECTOR PLUG
3 REV. A Fig. 2 BOLT SECURING THE CONNECTOR GUIDE BUSHING 1 - CATALYTIC CONVERTER (ZH AND WK MODELS ONLY) 2 - BAYONET LOCK 3 - BRONZE BOLT 4 - TRANSMISSION OIL PAN 6. Remove the connector guide bushing from the transmission. 7. If there is a locator tab present, using side cutter pliers, remove the locator tab on the connector guide bushing (Fig. 3).
4 REV. A BAYONET LOCK 2 - LOCATOR TAB 3 - O-RING (2) 4 - CONNECTOR GUIDE BUSHING Fig. 3 BUSHING LOCATOR TAB LOCATION 8. Using transmission fluid, lubricate and place 1 p/n AB o-ring and 1 p/n AB o-ring on the connector guide bushing. NOTE: The o-rings are two different sizes. Be careful to place the new o-rings in the correct location. 9. Install the connector guide bushing in the transmission. 10. Tighten the bronze bolt securing the guide bushing in place. Tighten the bronze bolt to 2.5 N m +/- 0.2 N m ( 22 in. lbs +/- 2 in. lbs.) (Fig. 2). 11. Connect the 13-pin plug connector. Secure the connector by turning the bayonet lock of the connector guide bushing clockwise. 12. Clean the area of any residual transmission fluid which may be present as a result of the repair. 13. Lower the vehicle. 14. Connect the negative battery cable and reset the clock. NOTE: Be sure to use the correct transmission fluid, Mopar p/n AA. 15. Check the transmission fluid and adjust as necessary. Refer to the service information available in TechCONNECT. Reference: Service Info, 21 - Transmission/Transaxle/Automatic - NAG1/Fluid - Standard Procedure. VA VEHICLE REPAIR PROCEDURE: 1. Disconnect and isolate the negative battery cable. 2. Raise the vehicle on a suitable hoist. 3. Disconnect the 13-pin connector plug by turning the bayonet lock of the connector guide bushing counter clockwise (Fig. 1).
5 REV. A 4. Place a suitable drain pan under the connector guide bushing to catch transmission fluid that may drain during the next step. 5. Using a 7 mm socket, loosen the bronze bolt securing the connector guide bushing. The bronze bolt is located in the center of the connector guide bushing (Fig. 2). 6. Remove the connector guide bushing from the transmission. 7. **2004 VA vehicles go to Step # VA vehicles go to Step #9.** 8. **Install a new connector guide bushing, p/n AA, in the transmission. Proceed to Step #12.** 9. If there is a locator tab present, using side cutter pliers, remove the locator tab on the connector guide bushing(fig. 3). 10. Using transmission fluid, lubricate and place 1 p/n AB o-ring and 1 p/n AB o-ring on the connector guide bushing. NOTE: The o-rings are two different sizes. Be careful to place the new o-rings in the correct location. 11. Install the connector guide bushing in the transmission. 12. Tighten the bronze bolt securing the guide bushing in place. Tighten the bronze bolt to 2.5 N m +/- 0.2 N m ( 22 in. lbs +/- 2 in. lbs.) (Fig. 2). 13. Connect the 13-pin plug connector. Secure the connector by turning the bayonet lock of the connector guide bushing clockwise. 14. Clean the area of any residual transmission fluid which may be present as a result of the repair. 15. Lower the vehicle. 16. Connect the negative battery cable. NOTE: Be sure to use the correct transmission fluid, Mopar p/n AA. 17. Check the transmission fluid and adjust as necessary. Refer to the service information available in TechCONNECT. Reference: Service Info, 21 - Transmission/Transaxle/Automatic - NAG1/Fluid - Standard Procedure. WK VEHICLE REPAIR PROCEDURE: 1. Disconnect and isolate the negative battery cable. 2. Raise the vehicle on a suitable hoist. 3. Remove the bolt and loosen the screw securing the 13 pin connector heat shield in the right front corner of the transmission assembly (Fig. 4). Remove the heat shield.
6 REV. A LOOSEN SCREW 2-13 PIN CONNECTOR HEAT SHIELD 3 - REMOVE BOLT Fig PIN CONNECTOR HEAT SHIELD 4. Disconnect the 13-pin connector plug by turning the bayonet lock of the connector guide bushing counter clockwise (Fig. 1). 5. Place a suitable drain pan under the connector guide bushing to catch transmission fluid that may drain during the next step. 6. Using a 7 mm socket, loosen the bronze bolt securing the connector guide bushing. The bronze bolt is located in the center of the connector guide bushing (Fig. 2). 7. Remove the connector guide bushing from the transmission. 8. If there is a locator tab present, using side cutter pliers, remove the locator tab on the connector guide bushing (Fig. 3). 9. Using transmission fluid, lubricate and place 1 p/n AB o-ring and 1 p/n AB o-ring on the connector guide bushing. NOTE: The o-rings are two different sizes. Be careful to place the new o-rings in the correct location. 10. Install the connector guide bushing in the transmission. 11. Tighten the bronze bolt securing the guide bushing in place. Tighten the bronze bolt to 2.5 N m +/- 0.2 N m ( 22 in. lbs +/- 2 in. lbs.) (Fig. 2). 12. Connect the 13-pin plug connector. Secure the connector by turning the bayonet lock of the connector guide bushing clockwise. 13. Position the 13 pin connector heat shield and install the bolt and tighten the screw securing the heat shield in the right front corner of the transmission assembly (Fig. 4). 14. Clean the area of any residual transmission fluid which may be present as a result of the repair. 15. Lower the vehicle. 16. Connect the negative battery cable. NOTE: Be sure to use the correct transmission fluid, Mopar p/n AA.
7 REV. A 17. Check the transmission fluid and adjust as necessary. Refer to the service information available in TechCONNECT. Reference: Service Info, 21 - Transmission/Transaxle/Automatic - NAG1/Fluid - Standard Procedure. ZH VEHICLE REPAIR PROCEDURE: 1. Disconnect and isolate the negative battery cable. 2. Raise the vehicle on a suitable hoist. 3. Disconnect the oxygen sensor harness connectors and reposition the oxygen sensor harness out of the way (Fig. 5). 4. Remove the oxygen sensor heat shield bolts and the heat shield (Fig. 5). 5. Remove the bolt and loosen the screw securing the 13 pin connector heat shield in the right front corner of the transmission assembly (Fig. 4). Remove the heat shield and set it aside. 6. Disconnect the 13-pin connector plug by turning the bayonet lock of the connector guide bushing counter clockwise (Fig. 1). 7. Place a suitable drain pan under the connector guide bushing to catch transmission fluid that may drain during the next step. 8. Using a 7 mm socket, loosen the bronze bolt securing the connector guide bushing. The bronze bolt is located in the center of the connector guide bushing (Fig. 2). 9. Remove the connector guide bushing from the transmission. 10. If there is a locator tab present, using side cutter pliers, remove the locator tab on the connector guide bushing (Fig. 3). 11. Using transmission fluid, lubricate and place 1 p/n AB o-ring and 1 p/n AB o-ring on the connector guide bushing. NOTE: The o-rings are two different sizes. Be careful to place the new o-rings in the correct location. 1 - OXYGEN SENSOR CONNECTORS 2 - HEAT SHIELD BOLTS Fig. 5 OXYGEN SENSOR HEAT SHIELD 12. Install the connector guide bushing in the transmission.
8 REV. A Tighten the bronze bolt securing the guide bushing in place. Tighten the bronze bolt to 2.5 N m +/- 0.2 N m ( 22 in. lbs +/- 2 in. lbs.) (Fig. 2). 14. Connect the 13-pin plug connector. Secure the connector by turning the bayonet lock of the connector guide bushing clockwise. 15. Position the 13 pin connector heat shield and install the bolt and screw securing the heat shield in the right front corner of the transmission assembly (Fig. 4). 16. Position the oxygen sensor heat shield onto the transmission housing and install the screw and bolt which secure the shield in place.(fig. 5). 17. Connect the oxygen sensor harness connectors and secure the wiring harness in the oxygen sensor heat shield (Fig. 5). 18. Clean the area of any residual transmission fluid which may be present as a result of the repair. 19. Lower the vehicle. 20. Connect the negative battery cable. NOTE: Be sure to use the correct transmission fluid, Mopar p/n AA. 21. Check the transmission fluid and adjust as necessary. Refer to the service information available in TechCONNECT. Reference: Service Info, 21 - Transmission/Transaxle/Automatic - NAG1/Fluid - Standard Procedure. POLICY: Reimbursable within the provisions of the warranty. TIME ALLOWANCE: Labor Operation No: Description Guide Bushing Seals, Replace 0.4 Hrs. Amount ** Adapter Plug/Guide Bushing, Replace 0.4 Hrs 2004 VA Only** FAILURE CODE: 71 Oil Leak
SUBJECT: Front Door Window Glass - Loose, Sticks, Binds, or Express-Up Reversal
NUMBER: 23-032-07 GROUP: Body DATE: August 2, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
SUBJECT: NAG1 (W5A580) Transmission - Shudder When Torque Converter Clutch Engages
NUMBER: GROUP: 21-011-05 REV. A Transmission DATE: July 14, 2005 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
NOTE: This bulletin applies to vehicles equipped with tilt steering (sales code SUA) and built on or after January 14, 2002.
NUMBER: GROUP: 19-005-04 REV. A Steering DATE: October 25, 2004 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves inspecting the ELSD connections for water intrusion and/or corrosion and repairing the wiring harness.
NUMBER: GROUP: 08 059 18 REV. A 08 Electrical DATE: May 5, 2018 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
SUBJECT: Intermittent Coolant Weepage From Upper Radiator Hose Or Radiator
NUMBER: GROUP: 07-005-15 REV. B Cooling DATE: August 11, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THIS BULLETIN IS BEING PROVIDED IN ADVANCE. DO NOT ORDER PARTS RELATED TO THIS BULLETIN UNTIL AFTER DECEMBER 31, 2004.
NUMBER: GROUP: 23-049-04 REV. A Body DATE: December 15, 2004 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
SUBJECT: RFE Transmission Filters - Delayed Engagement And Related Transmission DTC'S
NUMBER: 21-007-06 GROUP: Transmission DATE: April 07, 2006 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves installing a shim package and a tilt head housing assembly in the steering column upper tilt head.
NUMBER: 19-003-03 GROUP: Steering DATE: Aug. 29, 2003 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA
NUMBER: GROUP: 05-001-17 REV. A Brakes DATE: January 14, 2017 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves replacing the spring tip liners and installing spring clinch clip isolators.
NUMBER: GROUP: 02-04-00 Rev. A Suspension DATE: May 12, 2000 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
NOTE: It is no longer necessary to replace the shifter as an assembly.
NUMBER: GROUP: 21-016-06 REV. A Transmission & Transaxle DATE: November 15, 2006 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
SYMPTOM/CONDITION: The Service 4WD lamp is illuminated even though the truck is not a 4X4 vehicle.
NUMBER: GROUP: 08-032-00 REV. A Electrical DATE: Dec. 29, 2000 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
Qty. Part No. Description 1 (AR) NPN Lord Fusor 112B Structural Adhesive Or Equivalent
NUMBER: 23 006 18 GROUP: 23 Body DATE: February 13, 2018 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
NOTE: PERFORM THE PARKING BRAKE CABLE INSPECTION ON BOTH RIGHT AND LEFT REAR PARKING BRAKE CABLES.
NUMBER: 05-002-01 GROUP: Brakes DATE: Mar. 9, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
OVERVIEW: This bulletin involves replacing the spring tip liners and installing spring cinch clip isolators.
NUMBER: 02-13-99 GROUP: Suspension DATE: Sep. 10, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
Start the vehicle and allow it to idle. If the shake is experienced in either the steering wheel or seat, perform the Repair Procedure.
NUMBER: GROUP: 09-01-99 Rev. A Engine DATE: May 21, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
NOTE: This bulletin applies to vehicles built before August 20,2010 (MDH0820XX).
NUMBER: 23-005-13 GROUP: Body DATE: February 27, 2013 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
SYMPTOM/CONDITION: A ratcheting sound is heard from sunroof module as the glass approaches the full open position.
NUMBER: 23-004-08 GROUP: Body DATE: January 16, 2008 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
OVERVIEW: This bulletin involves **installing a rubber gasket** to the face of the half shaft that mounts to the hub bearing.
NUMBER: GROUP: 03-001-03 REV. A Axle and Propshaft DATE: Sept. 19, 2003 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
THIS BULLETIN IS BEING PROVIDED IN ADVANCE. DO NOT ORDER PARTS OR PERFORM ANY ACTIONS RELATED TO THIS BULLETIN UNTIL JANUARY 15, 2008.
NUMBER: 24-008-07 GROUP: Heating & A/C DATE: December 18, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves replacing the front brake caliper guide pin bushings (WK) Jeep Grand Cherokee (WD) Dodge Durango
NUMBER: 05-002-15 GROUP: Brakes DATE: April 24, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
OVERVIEW: This bulletin involves modifying or replacing the cowl trim panel fasteners to correct a water leak condition.
NUMBER: 23-034-14 REV. A GROUP: Body DATE: December 16, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
SUBJECT: Front Brake Pulsation During Light To Moderate Brake Application
NUMBER: GROUP: DATE: 05-003-02 REV. B Brakes Dec. 16, 2002l This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
SUBJECT: Long Engine Crank Time And/Or MIL Illumination Due To DTC P0340 / P0344
NUMBER: GROUP: 08-001-08 REV. A Electrical DATE: February 23, 2008 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
NUMBER: GROUP: DATE: November 12, 2005 SUBJECT: OVERVIEW: MODELS: SYMPTOM/CONDITION: REV A. Electrical
NUMBER: GROUP: 08-036-05 REV A Electrical DATE: November 12, 2005 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THIS BULLETIN IS BEING PROVIDED IN ADVANCE. DO NOT ORDER PARTS OR PERFORM ANY ACTIONS RELATED TO THIS BULLETIN UNTIL FEBRUARY 21, 2005.
NUMBER: 08-004-05 GROUP: Electrical DATE: January 26, 2005 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
NOTE: This bulletin applies to vehicles built before August 20,2010 (MDH0820XX).
NUMBER: GROUP: 23-016-10 REV.A Body DATE: September 25, 2010 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves inspecting and adjusting the transmission fluid to the correct level (MK) Jeep Compass/Patriot
NUMBER: 21-011-15 GROUP: Transmission and Transfer Case DATE: February 28, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
(RS) Town & Country, Caravan, Voyager (RG) Chrysler Voyager (International Markets)
NUMBER: 19-006-05 GROUP: Steering DATE: August 4, 2005 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
SUBJECT: Transmission Wiring Harness Repair Or Replacement For No Start Or Stiff Steering
NUMBER: GROUP: 08-039-16 REV. A Electrical DATE: June 14, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
Grand Cherokee. Durango
NUMBER: 17-002-14 GROUP: Rear Suspension DATE: July01, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin provides a diagnostic procedure for steering sensitivity.
NUMBER: GROUP: 19-002-01 REV. A Steering DATE: Sept. 28, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
SUBJECT: I/M Readiness Check Continues To Indicate OBD System Is Not Ready For I/M Testing
NUMBER: 25-001-07 GROUP: Emissions DATE: February 09, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
SUBJECT: New Repair Procedures With Separate Liftgate Latch Motor And Components
NUMBER: 23-020-02 GROUP: Body DATE: May 20, 2002 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in
THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH A GASOLINE ENGINE.
NUMBER: 14-002-01 GROUP: Fuel DATE: Mar. 16, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in
SUBJECT: Radio Speaker Misdiagnosis - Rattle/Buzz Sounds in Door Modules
NUMBER: GROUP: DATE: Body March 20, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval
SUBJECT: While In Bi-level Mode, Air Flow From Panel Vents Is Less Than That Of The Floor Vents
NUMBER: GROUP: 24-20-99 Rev. A Heating & A/C DATE: Dec. 17, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
ATTENTION ADVANCE SERVICE BULLETIN INFORMATION
NUMBER: 23-047-00 GROUP: Body EFFECTIVE DATE: Jan. 19, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves the replacement of the header seal and its associated butyl adhesive.
NUMBER: 23-025-08 GROUP: Body DATE: August 26, 2008 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
SUBJECT: Click, Creak, Or Groaning Sound Near C-Pillar, Dual Pane Sunroof (Sales Code GWJ)
NUMBER: 23-010-14 GROUP: Body DATE: April 04, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
OVERVIEW: This bulletin involves the replacement of the hydraulic clutch master cylinder and reservoir hose.
NUMBER: 06-001-16 GROUP: Clutch DATE: January 08, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
NUMBER: DATE: Jan. 17, SUBJECT: Wind Noise
NUMBER: 23-002-03 GROUP: Body DATE: Jan. 17, 2003 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in
THE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.
NUMBER: GROUP: 18-006-08 REV. A Vehicle Performance DATE: April 8, 2008 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA.
NUMBER: GROUP: 23-015-16 REV. A Body DATE: April 13, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin announces the release of parts to repair the power distribution center.
NUMBER: 08-07-99 GROUP: Electrical DATE: Mar. 12, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
IT IS RECOMMENDED THAT SPECIAL TOOL OT38793 (ELECTRONIC VIBRATION ANALYZER) BE USED TO HELP PINPOINT THE ROOT CAUSE OF THE VIBRATION.
NUMBER: 03-02-99 GROUP: Axles And Propshafts DATE: Mar. 26, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THE witech SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
NUMBER: 25-003-15 GROUP: Emissions Control DATE: October 06, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA.
NUMBER: 08-060-16 GROUP: Electrical DATE: May 11, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
OVERVIEW: This bulletin involves replacing the purge control valve hose assembly (KL) Jeep Cherokee (UF) Chrysler 200
NUMBER: 25-002-16 GROUP: Emissions Control DATE: September 27, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software.
NUMBER: 18-032-03 GROUP: Vehicle Performance DATE: Sep. 12, 2003 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves installing revised sliding door rear latch assembly and latch rods and modifying the rear latch opening.
NUMBER: 23-15-00 GROUP: Body DATE: April 21, 2000 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in
THE witech SOFTWARE VERSION MUST BE AT **15.02** OR HIGHER TO PERFORM THIS PROCEDURE.
NUMBER: GROUP: 21-030-14 REV. A Transmission and Transfer Case DATE: October 24, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
THE witech SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
NUMBER: 18-095-15 GROUP: Vehicle Performance DATE: November 25, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THE DRBIII FLASH FILES FOR THIS BULLETIN ARE AVAILABLE ON DealerCONNECT.
NUMBER: 18-033-04 GROUP: Vehicle Performance DATE: August 20, 2004 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
FOR HELP WITH USING witech FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION S HELP TAB.
NUMBER: GROUP: 18-003-17 REV. B Vehicle Performance DATE: February 21, 2017 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may
THE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.
NUMBER: GROUP: 18-003-07 REV. A Vehicle Performance DATE: March 7, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
OVERVIEW: This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software.
NUMBER: GROUP: 18-026-03 REV. A Vehicle Performance DATE: September 12, 2003 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
THIS BULLETIN IS BEING PROVIDED IN ADVANCE. THE SOFTWARE WILL BE AVAILABLE ON TechCONNECT ON OR AFTER DECEMBER 15, 2003.
NUMBER: 18-042-03 GROUP: Vehicle Performance DATE: November 28, 2003 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves installing heated seat heating element repair kits.
NUMBER: 08-03-99 GROUP: Electrical DATE: Feb. 5, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
FOR HELP WITH USING witech FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION S HELP TAB.
NUMBER: GROUP: 18-087-16 REV. A Vehicle Performance DATE: August 24, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may
OVERVIEW: This bulletin involves correcting a sealant void between the cowl plenum lower panel and dash crossmember.
NUMBER: 23-029-15 GROUP: Body DATE: July 21, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in
OVERVIEW: This bulletin involves replacing the inner doors and Instrument Panel (IP) appliques.
NUMBER: 23 054 17 GROUP: 23 Body DATE: December 22, 2017 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
NOTE: This bulletin applies to vehicles built on or after July 29, 2013 (MDH 0729XX) and on or before September 19, 2013 (MDH 0919XX).
NUMBER: 19-002-14 GROUP: Steering DATE: February 13, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves replacing all of the Tire Pressure Module (TPM) sensors.
NUMBER: GROUP: 22-002-15 REV. A Tires and wheels DATE: March 28, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
OVERVIEW: This bulletin involves installing a new antilock brake control module.
NUMBER: 08-035-00 GROUP: Electrical DATE: Nov. 10, 2000 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
THE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET. StarSCAN SOFTWARE LEVEL MUST BE AT RELEASE 8.03 OR HIGHER.
NUMBER: GROUP: 21-002-07 REV. E Transmission DATE: December 21, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
NOTE: This bulletin applies to CS models built after February 1, 2004 (MDH 0201XX) equipped with a 3.5L engine (Sales Code EGN).
NUMBER: 09-010-06 GROUP: Engine DATE: September 16, 2006 THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 09-005-05, DATED DECEMBER 2, 2005, WHICH SHOULD BE REMOVED FROM YOUR FILES. THIS IS A COMPLETE
THE SOFTWARE WILL BE AVAILABLE ON TechCONNECT ON FEBRUARY 3, 2004.
NUMBER: 18-002-04 GROUP: Vehicle Performance DATE: February 3, 2004 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THIS INFORMATION APPLIES TO VEHICLES EQUIPPED WITH A 3.9L, 5.2L, OR 5.9L ENGINE. AB MODELS WILL BE ADDED LATER (NEW PARTS REQUIRED).
SUBJECT: NO: 18-48-98 Ignition System Cross Fire/Secondary GROUP: Vehicle Performance Ignition Wire Induction DATE: Dec. 30, 1998 This bulletin is supplied as technical information only and is not an authorization
THE witech SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
NUMBER: 18-094-15 GROUP: Vehicle Performance DATE: November 25, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
Revised Air Conditioning Suction Line And Unified Line Installation Instructions
NUMBER: GROUP: 24 23 99 Air Conditioning EFFECTIVE DATE: Nov. 26, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
THE witech SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
NUMBER: GROUP: 18-021-15 REV. C Vehicle Performance DATE: June 10, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
2004 Dodge Pickup R1500 MIL ILLUMINATION DIAGNOSTIC TROUBLE CODES P0401, P0403, P0404, P0405, P0406 TECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN Reference Number(s): 18-021-04, Date of Issue: May 4, 2004 GROUP: Vehicle Performance SUBJECT MIL Illumination Diagnostic Trouble Codes P0401, P0403, P0404, P0405, P0406 OVERVIEW
THE SOFTWARE FOR THE DRB III WILL BE AVAILABLE ON DealerCONNECT JUNE 1, 2004.
NUMBER: 18-024-04 GROUP: Vehicle Performance DATE: June 1, 2004 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
FOR HELP WITH USING witech FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION S HELP TAB.
NUMBER: GROUP: 18-022-17 REV. B Vehicle Performance DATE: April 07, 2017 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may
THE DRBIII FLASH FILES FOR THIS BULLETIN ARE AVAILABLE ON DealerCONNECT.
NUMBER: GROUP: 18-006-04 REV. B Vehicle Performance DATE: September 13, 2004 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
THE DRBIII FLASH FILES FOR THIS BULLETIN ARE AVAILABLE ON DealerCONNECT.
NUMBER: 18-042-14 GROUP: Vehicle Performance DATE: July 30, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THE witech SOFTWARE LEVEL MUST BE AT RELEASE OR HIGHER TO PERFORM THIS PROCEDURE.
NUMBER: 18-006-12 GROUP: Vehicle Performance DATE: February 04, 2012 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin announces the release of parts to repair the power distribution center.
NUMBER: 08-07-99 GROUP: Electrical DATE: Mar. 12, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
THE witech SOFTWARE LEVEL MUST BE AT RELEASE OR HIGHER TO PERFORM THIS PROCEDURE.
NUMBER: 18-014-10 GROUP: Vehicle Performance DATE: April 28, 2010 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
OVERVIEW: This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software.
NUMBER: 21 001 18 GROUP: 21 Transmission and Transfer Case DATE: January 4, 2018 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
NUMBER: GROUP: DATE: Apr. 1, SUBJECT: Outside Rearview Mirror Glass Replacement MODELS: Body
NUMBER: 23-015-02 GROUP: Body DATE: Apr. 1, 2002 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in
OVERVIEW: This bulletin involves removing and installing the deck lid spoiler.
NUMBER: 23-041-05 GROUP: Body DATE: September 9, 2005 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
THE witech SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
NUMBER: GROUP: 21-021-15 REV. E Transmission and Transfer Case DATE: October 01, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
ATTENTION ADVANCE SERVICE BULLETIN INFORMATION
SUBJECT: NO: 21-10-98 Loss Of Fifth Gear GROUP: Transmission EFFECTIVE DATE: Sep. 11, 1998 CHRYSLER MAIL MANAGEMENT SYSTEM DATE: AUG. 28, 1998 ATTENTION ADVANCE SERVICE BULLETIN INFORMATION The following
SUBJECT: NO: Honk Or Squeal Noise During Parking Lot Maneuvers GROUP: Steering. DATE: Aug. 28, 1998
SUBJECT: NO: 19-05-98 Honk Or Squeal Noise During Parking Lot Maneuvers GROUP: Steering DATE: Aug. 28, 1998 THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETINS 19-07-97, DATED MAY 9, 1997 AND 19-11-97,
THE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET. StarSCAN SOFTWARE LEVEL MUST BE AT RELEASE 9.02 OR HIGHER.
NUMBER: 18-035-08 GROUP: Vehicle Performance DATE: September 13, 2008 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
This bulletin involves using new procedures when replacing/installing timing belt tensioner components.
NUMBER: GROUP: 09 06 00 Engine DATE: Mar. 10, 2000 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
2006 (LX) Chrysler 300, Dodge Magnum and Charger
Dealer Service Instructions for: Emissions Recall F47 Catalytic Converter and Reprogram PCM March 2007 Effective immediately all repairs on involved vehicles are to be performed according to this notification.
(JA) Breeze/Cirrus/Stratus (JR) Sebring Convertible/Sebring Sedan/Stratus Sedan (JX) Sebring Convertible
NUMBER: 08-030-06 REV. A GROUP: Electrical DATE: August 25, 2006 THIS BULLETIN SUPERSEDES SERVICE BULLETINS 08-030-06, DATED JULY 12, 2006, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED
RAPID RESPONSE TRANSMITTAL SERVICE ACTION # REV. B 3.5L #2 Rod Bearing and Crankshaft Journal Inspection for Contamination.
August 10, 2006 TO: FROM: SUBJECT: ALL CHRYSLER AND DODGE DEALERS GLOBAL SERVICE RAPID RESPONSE TRANSMITTAL SERVICE ACTION #06-025 REV. B 3.5L #2 Rod Bearing and Crankshaft Journal Inspection for Contamination.
FOR HELP WITH USING witech FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION S HELP TAB.
NUMBER: 21-019-17 GROUP: and Transfer Case DATE: April 22, 2017 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THE witech SOFTWARE LEVEL MUST BE AT OR HIGHER TO PERFORM THIS PROCEDURE.
NUMBER: 21-001-15 GROUP: and Transfer Case DATE: January 10, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
SB THE witech SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
SB-10058327-8669 NUMBER: GROUP: 18-009-15 REV. F Vehicle Performance DATE: September 19, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of
THE witech SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.
NUMBER: 18-057-15 GROUP: Vehicle Performance DATE: July 25, 2015 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
DATE: September 8, 2017
NUMBER: GROUP: 08 Electrical DATE: September 8, 2017 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
FOR HELP WITH USING witech FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION S HELP TAB.
NUMBER: 18-091-16 GROUP: Vehicle Performance DATE: July 26, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
THIS BULLETIN DOES NOT APPLY TO DIAMLERCHRYSLER CANADA DEALERS.
NUMBER: 08-025-01 GROUP: Electrical DATE: Nov. 23, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
DATE: Nov. 24, 2000 MODELS:
NUMBER: GROUP: 23-08-00 REV. B Body DATE: Nov. 24, 2000 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
OVERVIEW: This bulletin involves performing a Transmission Adaptation Learn procedure based on a subjective shift quality rating evaluation.
NUMBER: GROUP: 21-012-14 REV. B and Transfer Case DATE: September 26, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may