Before continuing with the installation, here are a few definitions you should be aware of:

Size: px
Start display at page:

Download "Before continuing with the installation, here are a few definitions you should be aware of:"

Transcription

1 MSD Ford Billet Distributors PN 8473: 2.3L, PN 8580: 351C, 351M, 400, 429, 460 PN 8582: 289, 302, PN 8584: 351W PN 85805: 351W w/edelbrock Victor Jr. Intake Important: Read these instructions before attempting the installation. Note: An MSD Ignition is required with this Distributor. Parts Included: 1 - Billet Distributor 1 - Rotor 1 - Distributor Cap 1 - Advance Kit 1 - Tube of Gear Lubricant 1 - O-Ring WARNING: Before installing the MSD Distributor, disconnect the battery cables. When disconnecting the battery cables, always remove the Negative (-) cable first and install it last. Note: These distributors must be used with an MSD Ignition Control. TIMING FUNCTIONS Before continuing with the installation, here are a few definitions you should be aware of: Initial Timing: This is the base timing (also referred to as idle timing) of the engine before the centrifugal advance begins. Centrifugal Advance: The centrifugal (or mechanical) advance mechanism is made up of weights, springs, advance cams, and an advance stop bushing. The amount and rate of advance that your distributor is capable of is determined by the centrifugal timing. If you ever wish to lock out the centrifugal advance, refer to the centrifugal advance section. Total Timing: This is the total of the initial timing plus the centrifugal advance added together. Example: 10 Initial 25 centrifugal = 35 Total Timing. Note: MSD Distributors are supplied with the heavy (slow) advance springs installed. This is to prevent detonation in certain applications. Review the information on pages 2-4 to determine the best advance curve for your application.

2 INSTALLATION INSTRUCTIONS CHOOSING AN ADVANCE CURVE The function of the advance curve is to match the ignition timing to the burning rate of the fuel and speed (rpm) of the engine. Any factor that changes the burning rate of the fuel or the engine speed can cause a need for an ignition timing change. Figure 1 shows some of the factors that will affect engine timing. FACTOR Advance Timing Retard Timing For For Cylinder Pressure Low High Vacuum High Low Energy of Ignition Low High Fuel Octane High Low Mixture (Air/Fuel) Rich Lean Temperature Cool Hot Combustion Chamber Shape Open Compact Spark Plug Location Offset Center Combustion Turbulence Low High Load Light Heavy Figure 1 Ignition Timing Factors. As you can see from the chart, most factors will change throughout the range of the engine operation. The timing mechanism of the distributor must make timing changes based on these factors. Example: An engine has 11:1 compression with a high energy ignition. With the specifications given, you will have to retard the timing for the high compression and high energy ignition. By comparing the engine s specifications against the chart, a usable timing guideline can be found. Engines with a combination of items from both columns will require a timing that is set in the mid range. Obviously a full technical explanation of correct ignition timing would be very complicated. The best way to arrive at a suitable ignition curve for your engine is to use the Ignition Timing Factors Chart as a guide and compare it to the Advance Graphs in Figure 4 until a suitable curve is found. When selecting your advance curve, use detonation (engine ping) as an indicator of too much advance, and a decrease in power as an indicator of too little advance. Tips on Selecting an Advance Curve Use as much initial advance as possible without encountering excessive starter load. Start the centrifugal advance just above the idle rpm. The starting point of the centrifugal advance curve is controlled by the installed length and tension of the spring. How quickly the centrifugal advance (slope) comes in is controlled by the spring stiffness. The stiffer the spring, the slower the advance curve. The amount of advance is controlled by the advance bushing. The bigger the bushing, the smaller the amount of advance.

3 INSTALLATION INSTRUCTIONS CENTRIFUGAL ADVANCE CURVE Selecting the Advance Springs The rate, or how quick the advance comes in is determined by the type of springs which are installed on the distributor. The MSD distributors are equipped with two Heavy Silver springs installed. These will give you the slowest advance curve possible (Figure 2). The parts kit contains two additional sets of springs which can be used to match the advance curve to your particular application. Refer to the Spring Combination Chart (Figure 3) for combinations that can be achieved. To change the springs, remove the cap and rotor and use needlenose pliers to remove the springs. Be sure the new springs seat in the groove on the pin. Timing Curve From Factory Figure 2 The Factory Equipped Curve. SPRING COMBINATION RATE OF ADVANCE FIGURE 4 2- Heavy Silver SLOWEST A 1- Heavy Silver B 1- Light Blue 1-Heavy Silver C 1-Light Silver 2- Light Blue D 1- Light Silver E 1- Light Blue 2- Light Silver FASTEST F Figure 3 Spring Combination Chart. Figure 4 Advance Curves.

4 INSTALLATION INSTRUCTIONS Selecting the Advance Stop Bushing Three different advance stop bushings are supplied in the distributor kit. The distributor comes with a Blue (21 ) bushing already installed. If a different amount of centrifugal advance is desired, follow the next procedure to change the bushings. The chart in Figure 5 gives the size and approximate degrees for the corresponding bushings. BUSHING SIZE APPROXIMATE CRANKSHAFT DEGREES Red-Smallest 28 Silver 25 Blue 21 Black-Largest 18 Figure 5 Advance Stop Bushing Chart. Changing the Advance Stop Bushings 1. Remove the distributor cap and rotor. 2. Remove the locknut and washer on the bottom of the advance assembly (Figure 6). 3. Remove the bushing and install the new one. Install the washer and locknut. Locking Out the Centrifugal Advance 1. Remove the advance components including the springs, weights and the advance stop bushing from the advance assembly. 2. Remove the roll-pin from the shaft retaining sleeve and slide the shaft up. 3. Rotate the shaft 180 and insert the advance stop bushing pin into the small hole on the advance plate (Figure 7). 4. Install the locknut and washer to the advance stop bushing pin. This locks the advance in place. 5. Install the retaining sleeve and its roll-pin. Figure 6 Changing the Advance Stop Bushing. Figure 6 Locking Out the Centrifugal Advance. Figure 7 Locking Out the Advance.

5 INSTALLATION INSTRUCTIONS INSTALLING THE DISTRIBUTOR 1. Remove the existing distributor cap without disconnecting any of the spark plug wires. 2. With the cap off, crank the engine until the rotor is aimed at a fixed point on the engine or firewall. Note this position by making a mark (Figure 8). 3. Place the distributor cap back on and note which plug wire the rotor is pointing to. MARK THE SPARK PLUG WIRES and remove the distributor cap. 4. Disconnect the wiring from the distributor. 5. Loosen the distributor hold down clamp and slide the clamp out of the way. 6. Lift the distributor out of the engine. Note that the rotor rotates as you lift the distributor out. This is due to the helical cut gear and should be taken into consideration when installing the Figure 8 Marking the Rotor Location. new distributor. 7. Install the new O-ring and apply a liberal amount of the supplied lubricant to the distributor gear. 8. Install the distributor making sure that the rotor comes to rest pointing at the fixed mark. If the distributor will not fully seat with the rotor pointing to the marked position, you may need to rotate the oil pump shaft until the rotor lines up and the distributor fully seats. 9. Position and tighten the hold down clamp onto the distributor. 10. Install the distributor cap and spark plug wires one at a time to ensure correct location.

6 7200 INSTALLATION INSTRUCTIONS WARNING: High voltage is present on the coil terminals. Do not touch the terminals or coil tower when the engine is cranking or running. TO 12V IGNITION KEY FROM IGNITION KEY (ORIGINAL COIL WIRE) HEAVY RED HEAVY BLACK RED WHITE (NOT USED) ORANGE BLACK TACH OUTPUT IGNITION Multiple Spark Discharge AUTOTRONIC CONTROLS CORPORATION PART NO. SERIAL NO.. GREEN PN 8860 HARNESS VIOLET Figure 9 Wiring to an MSD 6-Series Ignition Control. PRO POWER COIL TO 12V HEAVY BLACK ORANGE BLACK IGNITION KEY FROM IGNITION KEY (ORIGINAL COIL WIRE) HEAVY RED C C- RED GROUND RPM T A C H IGN PTS M M- WHITE (NOT USED) VIOLET GREEN PN 8860 HARNESS VIOLET GREEN Figure 10 Wiring to an MSD 7-Series Ignition Control.

7 INSTALLATION INSTRUCTIONS HEAVY RED HEAVY BLACK ORANGE T A C H C C- IGN PTS M M- NOT USED RED BLACK SWITCHED 12 VOLTS FROM IGNITION KEY NOT USED WHITE GREEN TIMING CONTROL WHITE YELLOW RED VIOLET Note: MSD 6 and 7 Series Ignitions share the same color wiring. TO GROUND Figure 11 Wiring with an MSD 7-Series Ignition and Timing Control. REPLACING THE DISTRIBUTOR GEAR To replace the distributor gear on the MSD Distributors, the following steps must be followed. 1. Remove the original spiral pin with a punch and press the original gear off the shaft. Press the new gear onto the shaft and line up the holes for the spiral pin. Note: The holes may not line up. 2. If the holes line up, measure the distance as shown in the diagram. If the measurement is not correct or the holes do not line up, a new hole must be drilled. If the measurement is within specifications and the holes line up, install a new spiral pin. 3. To drill a new hole, turn the gear on the shaft so the gear hole is approximately 90 to the original shaft hole. Carefully position the gear on the shaft to match the specifications given in the drawing. Note: Before measuring, push the shaft in to remove all of the end play. 4. When the gear is in the correct position, drill a hole through the distributor shaft. Install a new spiral pin and recheck the measurement. Note: If the measurement is not within specifications after drilling, a slight correction can be made by machining the upper face of the thrust collar. Do not remove more than or rotor-to-cap interference may result. THRUST COLLAR PRESS FIRMLY TO TAKE OUT ALL END PLAY BEFORE MEASURING MAX MIN. Figure 12 Replacing the Distributor Gear.

8 Tech Notes Service In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty. When returning MSD components for warranty service, Proof of Purchase must be supplied for verification. After the warranty period has expired, repair service is based on a minimum and maximum fee. All returns must have a Return Material Authorization (RMA) number issued to them before being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or visit our website at to automatically obtain a number and shipping information. When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered by warranty). For more information, call MSD Ignition at (915) MSD technicians are available from 7:00 a.m. to 6:00 p.m. Monday - Friday (mountain time). Limited Warranty MSD IGNITION warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void for any products purchased through auction websites. If found to be defective as mentioned above, it will be repaired or replaced at the option of MSD Ignition. Any item that is covered under this warranty will be returned free of charge using Ground shipping methods. This shall constitute the sole remedy of the purchaser and the sole liability of MSD Ignition. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or fitness. In no event shall MSD Ignition or its suppliers be liable for special or consequential damages. *Intended normal use means that this item is being used as was originally intended and for the original application as sold by MSD Ignition. Any modifications to this item or if it is used on an application other than what MSD Ignition markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item will work for the application they are intending. MSD Ignition will accept no liability for custom applications Autotronic Controls Corporation FRM29111 Revised 12/07 Printed in U.S.A.

MSD Pro-Billet Ford FE Distributor PN 8594

MSD Pro-Billet Ford FE Distributor PN 8594 MSD Pro-Billet Ford FE Distributor PN 8594 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition is required with this Distributor. Parts Included: 1 - Pro-Billet

More information

MSD Pro-Billet Chrysler V8 Distributor PN , 400 PN , 440

MSD Pro-Billet Chrysler V8 Distributor PN , 400 PN , 440 MSD Pro-Billet Chrysler V8 Distributor PN 8545-383, 400 PN 8546-426, 440 Important: Read these instructions before attempting the installation. Note: An MSD Ignition Control is required to use these distributors.

More information

MSD Billet Distributor Buick V6 Even-Fire PN 8551

MSD Billet Distributor Buick V6 Even-Fire PN 8551 MSD Billet Distributor Buick V6 Even-Fire PN 8551 Important: Read these instructions before attempting the installation. Parts Included: 1 - Billet Distributor 1 - Rotor, PN 8467 1 - Distributor Cap, PN

More information

MSD Pro-Billet V8 Distributor Buick 400, 430, 455, PN 8517 Buick 215, 300, 340, 350, PN 8548 Oldsmobile, PN 8566 Pontiac, PN 8563

MSD Pro-Billet V8 Distributor Buick 400, 430, 455, PN 8517 Buick 215, 300, 340, 350, PN 8548 Oldsmobile, PN 8566 Pontiac, PN 8563 MSD Pro-Billet V8 Distributor Buick 400, 430, 455, PN 8517 Buick 215, 300, 340, 350, PN 8548 Oldsmobile, PN 8566 Pontiac, PN 8563 Important: Read these instructions before attempting the installation.

More information

MSD Pro-Billet Small Diameter Ford V8 Distributor PN 8577/85773; 351C-460, PN 8578/85783; 351W PN 8579/85793; 302

MSD Pro-Billet Small Diameter Ford V8 Distributor PN 8577/85773; 351C-460, PN 8578/85783; 351W PN 8579/85793; 302 MSD Pro-Billet Small Diameter Ford V8 Distributor PN 8577/85773; 351C-460, PN 8578/85783; 351W PN 8579/85793; 302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product

More information

MSD Pro-Billet Flat-Top Chevrolet V8 Distributor PN 84891

MSD Pro-Billet Flat-Top Chevrolet V8 Distributor PN 84891 MSD Pro-Billet Flat-Top Chevrolet V8 Distributor PN 84891 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product

More information

MSD Pro-Billet Marine Distributor Chevrolet, PN 8560, with Slip Collar, PN 8562, Ford, PN 85806

MSD Pro-Billet Marine Distributor Chevrolet, PN 8560, with Slip Collar, PN 8562, Ford, PN 85806 MSD Pro-Billet Marine Distributor Chevrolet, PN 8560, with Slip Collar, PN 8562, Ford, PN 85806 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor

More information

MSD Pro-Billet Small Diameter Street Ford V8 Distributor PN 8477; 351C-460, PN 8478; 351W PN 8479; 289/302

MSD Pro-Billet Small Diameter Street Ford V8 Distributor PN 8477; 351C-460, PN 8478; 351W PN 8479; 289/302 MSD Pro-Billet Small Diameter Street Ford V8 Distributor PN 8477; 351C-460, PN 8478; 351W PN 8479; 289/302 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet

More information

MSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570

MSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570 MSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your

More information

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501 MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN 85561 Extra Tall, PN 8547 with Locked-Out Timing, PN 85501 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product

More information

MSD Pro-Billet Dual Pickup Ford Distributor PN 8384; 351W PN 8382; 289/302

MSD Pro-Billet Dual Pickup Ford Distributor PN 8384; 351W PN 8382; 289/302 MSD Pro-Billet Dual Pickup Ford Distributor PN 8384; 351W PN 8382; 289/302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty

More information

Before continuing with the installation, here are a few definitions you should be aware of:

Before continuing with the installation, here are a few definitions you should be aware of: MSD Pro-Billet Small Diameter Street Ford V8 Distributor 351C-460: PN 8477, PN 84771 steel gear, 351W: PN 8478, PN 84781 steel gear, 289/302: PN 8479, PN 84791 steel gear ONLINE PRODUCT REGISTRATION: Register

More information

MSD Pro-Billet Chrysler V8 Distributor PN , 400 PN , 440

MSD Pro-Billet Chrysler V8 Distributor PN , 400 PN , 440 MSD Pro-Billet Chrysler V8 Distributor PN 8545-383, 400 PN 8546-426, 440 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition Control is required to use these distributors.

More information

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360 MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor

More information

MSD Pro-Billet Chevrolet HEI Distributor PN 8365

MSD Pro-Billet Chevrolet HEI Distributor PN 8365 MSD Pro-Billet Chevrolet HEI Distributor PN 8365 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor, PN 8365 1 - Rotor, PN 84101 1 - Distributor

More information

MSD Pro-Billet Front Mount Ford Flathead Distributor 2-Bolt, , PN Bolt, , PN 8353

MSD Pro-Billet Front Mount Ford Flathead Distributor 2-Bolt, , PN Bolt, , PN 8353 MSD Pro-Billet Front Mount Ford Flathead Distributor 2-Bolt, 1942-1948, PN 8351 3-Bolt, 1932-1941, PN 8353 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help

More information

MSD Pro-Billet Chevrolet HEI Distributor PN 8365

MSD Pro-Billet Chevrolet HEI Distributor PN 8365 MSD Pro-Billet Chevrolet HEI Distributor PN 8365 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and

More information

MSD Pro-Billet Dual Pickup Chevrolet V8 Distributor

MSD Pro-Billet Dual Pickup Chevrolet V8 Distributor MSD Pro-Billet Dual Pickup Chevrolet V8 Distributor PN 8356 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor

More information

MSD Pro-Billet Chevrolet HEI Distributor PN 8365

MSD Pro-Billet Chevrolet HEI Distributor PN 8365 MSD Pro-Billet Chevrolet HEI Distributor PN 8365 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering

More information

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501 MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN 85561 Extra Tall, PN 8547 with Locked-Out Timing, PN 85501 Important: Read these Instructions before attempting the installation. Parts Included:

More information

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 Important: Read these Instructions before attempting the installation. Parts Included: 1

More information

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever

More information

MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595

MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark

More information

MSD Pro-Billet Chrysler Distributor PN Early Hemi

MSD Pro-Billet Chrysler Distributor PN Early Hemi MSD Pro-Billet Chrysler Distributor PN 83891-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your

More information

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393 MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly

More information

Before continuing with the installation, here are a few definitions you should be aware of:

Before continuing with the installation, here are a few definitions you should be aware of: MSD Pro-Billet Distributor Cadillac V8 (368, 425, 472, 500), PN 8363 AMC V8, PN 8519 Jeep Inline-6, PN 8516 Chevrolet Inline-6 (194, 230, 250, 292), PN 8515 ONLINE PRODUCT REGISTRATION: Register your MSD

More information

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition is required with this

More information

MSD Billet VW Distributor PN 8485

MSD Billet VW Distributor PN 8485 MSD Billet VW Distributor PN 8485 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653

MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653 MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with

More information

MSD Pro-Billet Ford FE Distributor PN 8594

MSD Pro-Billet Ford FE Distributor PN 8594 MSD Pro-Billet Ford FE Distributor PN 8594 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition is required with this Distributor. Parts Included: 1 - Pro-Billet

More information

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi MSD Pro-Billet Ready-to-Run Chrysler Distributor PN 8391-331/354 Early Hemi PN 8389-392 Early Hemi Important: Read these Instructions before attempting the installation. Note: An MSD Ignition Control is

More information

MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302

MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your

More information

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our

More information

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573 MSD Pro-Billet Ready-to-Run Ford Flathead, 1949-1953 PN 8573 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your

More information

MSD Pro-Billet Ready-to-Run Distributors Pontiac, PN 8528 Oldsmobile, PN 8529

MSD Pro-Billet Ready-to-Run Distributors Pontiac, PN 8528 Oldsmobile, PN 8529 MSD Pro-Billet Ready-to-Run Distributors Pontiac, PN 8528 Oldsmobile, PN 8529 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor,

More information

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573 MSD Pro-Billet Ready-to-Run Ford Flathead, 1949-1953 PN 8573 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor

More information

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi MSD Pro-Billet Ready-to-Run Chrysler Distributor PN 8391-331/354 Early Hemi PN 8389-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there

More information

Installation Instructions MSD Billet VW Distributor PN 8485

Installation Instructions MSD Billet VW Distributor PN 8485 Installation Instructions MSD Billet VW Distributor PN 8485 Important: Read these Instructions before attempting the installation. Contents Timing Functions Choosing an Advance Curve Setting or Locking

More information

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will

More information

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501/85505

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501/85505 MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN 85561 Extra Tall, PN 8547 with Locked-Out Timing, PN 85501/85505 We at MSD are proud to offer a high quality product at the industries most

More information

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor 1 - Rotor,

More information

MSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570

MSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570 MSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor

More information

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor

More information

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue

More information

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor

More information

MSD Pro-Billet Distributor Buick 400, 430, PN 8552 Buick Nailhead - PN 8524

MSD Pro-Billet Distributor Buick 400, 430, PN 8552 Buick Nailhead - PN 8524 MSD Pro-Billet Distributor Buick 400, 430, 455 - PN 8552 Buick Nailhead - PN 8524 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor,

More information

MSD Start/Retard Control PN 8982

MSD Start/Retard Control PN 8982 MSD Start/Retard Control PN 8982 IMPORTANT: Read the instructions before attempting installation. Parts Included: 1 - Start/Retard Control, PN 8982 4 - Retard Modules, 0, 2, 3, 4 1 - Wiring Kit 4 - Mounting

More information

3-Stage Retard PN 8970

3-Stage Retard PN 8970 3-Stage Retard PN 8970 IMPORTANT: Read the instructions before attempting the installation. Parts Included: 1-3-Stage Retard Control 4 - Mounting Screws 4 - Mounting Grommets 6 - Retard Modules, 2, 3,

More information

MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010

MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 Parts Included 1 Ignition Controller, PN 6010 1 Pro-Data+ Software CD 1 Harness 1 Parts Bag 6 Timing Modules Optional Accessories

More information

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 INSTALLATION INSTRUCTIONS MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 Parts Included: 1 - Ignition 1 - Wiring Harness 1 - Parts Bag 1 - CD ROM WARNING: When installing the SB6, disconnect

More information

MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012

MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012 MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty

More information

3-Stage Retard PN 8970

3-Stage Retard PN 8970 3-Stage Retard PN 8970 IMPORTANT: Read the Instructions before attempting the installaiton. Parts Included: 1-3-Stage Retard Control 4 - Mounting Screws 4 - Mounting Grommets 6 - Retard Modules, 2, 3,

More information

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with

More information

ProMaster Ignition Coil PN 29440

ProMaster Ignition Coil PN 29440 ProMaster Ignition Coil PN 29440 Parts Included: 1 - Ignition Coil 1 - Ignition Coil Bracket 1 - Screw, #10 x 1" 1 - Coil Wire Boot 1 - Coil Wire Terminal 2 - Ring Terminals 3 - Screws, #10 x 3/4" GENERAL

More information

MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013

MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013 MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013 Parts Included: 1 - Ignition Controller, PN 6013 1 - Pro-Data+ Software CD 1 - Parts Bag 1 - Mounting Template Optional Accessories: Hand

More information

MSD-8 Plus Ignition PN 7805

MSD-8 Plus Ignition PN 7805 MSD-8 Plus Ignition PN 7805 Note: Solid Core spark plug wires cannot be used with an MSD Ignition. Parts Included: 1 - MSD-8 Plus Ignition 1 - Mag Pickup Extension Harness, PN 8860 4 - Vibration Mounts

More information

MSD Blaster Ignition PN 5900

MSD Blaster Ignition PN 5900 MSD Blaster Ignition PN 5900 Note: Read these instructions completely before attempting any installation. Parts Included: 1 - Blaster Ignition, PN 5900 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground

More information

MSD Single Cylinder Programmable Ignition PN 4217

MSD Single Cylinder Programmable Ignition PN 4217 MSD Single Cylinder Programmable Ignition PN 4217 Parts Included: 1 - PN 4217 1 - PN 4217 Wire Harness 1 - CD Rom 9609 1 - Parts Bag 1 - Serial Cable WARNING: During installation, disconnect the battery

More information

MSD Pro Mag Information

MSD Pro Mag Information MSD 44 Amp Pro Mag Generator Clockwise Rotation - PN 8130, PN 81303, PN 81305, PN 81307 Counterclockwise Rotation PN 8140, PN 81403, PN 81405, PN 81407 Parts Included In This Kit: 1 44 Amp Pro Mag Generator

More information

MSD 7AL-3, Ignition Control PN 7230

MSD 7AL-3, Ignition Control PN 7230 MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,

More information

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 Parts Included 1 - Ignition Controller, PN 6011 1 - Pro-Data+ Software CD 1 - Harness 1 - Parts Bag 1-2-Bar MAP Sensor Optional Accessories

More information

MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740

MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issued with

More information

MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020

MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 INSTALLATION INSTRUCTIONS 1 MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 Important: Read these instructions before attempting this installation! Parts Included: 1 - MSD Stacker Ignition

More information

MSD Zero-Cross Distributor Chevrolet - PN 83971

MSD Zero-Cross Distributor Chevrolet - PN 83971 MSD Zero-Cross Distributor Chevrolet - PN 83971 Parts Included: 1 Distributor 1 Gasket 1 Hold Down & Hardware 1 Gear Lubricant 2 O-Rings IMPORTANT The Separate Pickup Zero-Cross Distributors use two completely

More information

MSD-8 Plus Ignition PN 7805

MSD-8 Plus Ignition PN 7805 MSD-8 Plus Ignition PN 7805 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team

More information

MSD Circle Track LS Ignition Control PN 6014CT

MSD Circle Track LS Ignition Control PN 6014CT MSD Circle Track LS Ignition Control PN 6014CT ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and

More information

MSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251

MSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251 MSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251 Parts Included: 1 - MSD Enhancer CD Ignition 2-6mm Stainless Steel Flatwashers 2 - Zip Ties Supplies Required For Installation 1 Tube of Blue Loctite

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS www.factorydirectperf.com Made exclusively for FDP by SEA-DOO 800 Enhancer Ignition, PN 30-08-2630 Fits SEA-DOO XP, GSX, GTX Watercraft w/rave Engine IMPORTANT: Read these instructions

More information

MSD Circle Track Ignition PN 6427

MSD Circle Track Ignition PN 6427 MSD Circle Track Ignition PN 6427 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

MSD Marine Ignitions 6M-2L, PN 6560

MSD Marine Ignitions 6M-2L, PN 6560 MSD Marine Ignitions 6M-2L, PN 6560 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

MSD Boost Control Module PN 77631

MSD Boost Control Module PN 77631 MSD Boost Control Module PN 77631 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

MSD Boost Control Module PN 7763

MSD Boost Control Module PN 7763 MSD Boost Control Module PN 7763 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

MSD Digital 6M-3L Marine Ignition PN 6564

MSD Digital 6M-3L Marine Ignition PN 6564 MSD Digital 6M-3L Marine Ignition PN 6564 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps

More information

Mallory HyFire Electronic Ignition Control

Mallory HyFire Electronic Ignition Control Mallory HyFire Electronic Ignition Control PN 690 Parts Included: 1 - Ignition 1 - Harness, Mag Pickup 1-18" Ground Wire 1-100V/1A Diode 4 - Mounting Screws WARNING: During installation, disconnect the

More information

ONLINE PRODUCT REGISTRATION:

ONLINE PRODUCT REGISTRATION: Atomic AirForce Intake Manifold for LT-1 2014-on Corvette PN 2700, PN 27003 (Black), PN 27004 (Gray) ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if

More information

Street Fire CDI PN 5520

Street Fire CDI PN 5520 Street Fire CDI ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if

More information

MSD Programmable Shift Controller PN 7559

MSD Programmable Shift Controller PN 7559 MSD Programmable Shift Controller PN 7559 WARNING: During installation, disconnect the battery cables. When Disconnecting, always remove the Negative cable first and install it last. Parts Included: 1

More information

WARNING. Atomic AirForce Intake Manifold for

WARNING. Atomic AirForce Intake Manifold for Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701 LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702 LS3/L99, 2008-2013 Corvette and 2010-2014 Camaro

More information

MSD 7AL-2 Plus Ignition

MSD 7AL-2 Plus Ignition MSD 7AL-2 Plus Ignition PN 7222/72223 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the

More information

MSD Digital-7 Plus Ignition Control PN 7520

MSD Digital-7 Plus Ignition Control PN 7520 INSTALLATION INSTRUCTIONS MSD Digital-7 Plus Ignition Control PN 7520 Parts Included: 1 - MSD Ignition 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground Wire 1 - White Jumper 1 - Red Jumper 2 - Violet

More information

MSD LS Ignition Control PN 6014/60143

MSD LS Ignition Control PN 6014/60143 MSD LS Ignition Control PN 6014/60143 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the

More information

Ford V8 Distributor Installation Instructions with Mechanical Advance

Ford V8 Distributor Installation Instructions with Mechanical Advance Ford V8 Distributor Installation Instructions with Mechanical Advance These instructions will help you to install a Ford V8 distributor with Mechanical Advance style distributor. Please read these instructions

More information

WARNING. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal

WARNING. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701, PN 27013 (Black), PN 27014 (Gray) LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702, PN 27023 (Black),

More information

MSD Pulse Ignition for Harley-Davidson PN 42211

MSD Pulse Ignition for Harley-Davidson PN 42211 MSD Pulse Ignition for Harley-Davidson PN 42211 IMPORTANT: Read these instructions before attempting the installation! It is also recommended to have your bike s Service Manual available during the installation.

More information

ACCEL SUPER BOX P/N 61212

ACCEL SUPER BOX P/N 61212 FRM 34395 INSTALLATION INSTRUCTIONS ACCEL SUPER BOX P/N 61212 PARTS INCLUDED: (x1) Ignition (x1) 18 Ground Wire (x4) Mounting Screws (x1) Harness (x1) 100V/1A Diode WARNING! During installation, disconnect

More information

MSD Digital SCI+ Ignition Control, PN 6350

MSD Digital SCI+ Ignition Control, PN 6350 MSD Digital SCI Ignition Control, PN 6350 Parts Included: 1 - MSD Ignition 1 - Harness, PN 8860 1 - Parts Bag, ASY19864 WARNING: During installation, disconnect the battery cables. When disconnecting the

More information

MSD 40th Anniversary 6AL Ignition Control

MSD 40th Anniversary 6AL Ignition Control MSD 40th Anniversary 6AL Ignition Control PN 6440 Congratulations on the purchase of your MSD 40th Anniversary 6AL Ignition Control! Not only is this limited edition (one of 4,000) Ignition Control going

More information

MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425

MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425 INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm

More information

PLATINUM SERIES. Haltech. High Power Igniter Module QUICK START GUIDE. 4 Channel - # HT Channel - # HT Channel - # HT020040

PLATINUM SERIES. Haltech. High Power Igniter Module QUICK START GUIDE. 4 Channel - # HT Channel - # HT Channel - # HT020040 PLATINUM SERIES Haltech High Power Igniter Module QUICK START GUIDE 4 Channel - # HT020032 6 Channel - # HT020036 8 Channel - # HT020040 HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL:

More information

ULTRA TEAM TABLE OF CONTENTS I. INTRODUCTION

ULTRA TEAM TABLE OF CONTENTS I. INTRODUCTION JACOBS "i.c.e. PAK" -. (import Car Energy PAK) ULTRA TEAM INSTALLATION INSTRUCTIONS LEGAL FOR INSTALLATION IN ALL 50 STATES PER CARB EO #D-19-32 NOTE TO INSTALLER:' Before starting installation, read this

More information

USER GUIDE 1 USER GUIDE

USER GUIDE 1 USER GUIDE USER GUIDE 1 USER GUIDE 1 TABLE OF CONTENTS IN THE BOX...3 NAVIGATING THE MENUS...3 MENU LAYOUT...3 UPDATE YOUR PROGRAMMER...4 CONNECT WITH THE MOTORCYCLE...5 TUNE YOUR MOTORCYCLE...6 ADDITIONAL FEATURES...8

More information

MSD Digital 6 Plus Ignition Control, PN 6520

MSD Digital 6 Plus Ignition Control, PN 6520 MSD Digital 6 Plus Ignition Control, PN 6520 Parts Included: 1 - MSD Ignition 2 - Violet Jumpers 4-45 Faston Terminals 1 - Harness, PN 8860 4 - Vibration Mounts and Hardware 2 - Wire Caps 1 - Harness,

More information

MSD Digital 6A and 6AL Ignition Control 6A - PN 6201/62013, 6AL - PN 6425/64253

MSD Digital 6A and 6AL Ignition Control 6A - PN 6201/62013, 6AL - PN 6425/64253 INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201/62013, 6AL - PN 6425/64253 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will

More information

ATD-5598 Self-Powered Inductive Clamp Timing Light

ATD-5598 Self-Powered Inductive Clamp Timing Light ATD-5598 Self-Powered Inductive Clamp Timing Light The original battery powered timing light, built with quality to last. There's no need to connect to a 12V battery for power. Unit is powered by (2) D

More information

MSD DIS-2 Plus Ignition PN MSD DIS-4 Plus Ignition PN 62152

MSD DIS-2 Plus Ignition PN MSD DIS-4 Plus Ignition PN 62152 MSD DIS-2 Plus Ignition PN 62112 MSD DIS-4 Plus Ignition PN 62152 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FRM34418 (REV. B) 09/17 UNILITE DISTRIBUTOR This product is applicabl e to pre-1966 California and pre-1968 federally certified passenger cars. It is also applicable to non-emission

More information

12-Volt Negative Ground Installation Instructions

12-Volt Negative Ground Installation Instructions 12-Volt Negative Ground Installation Instructions For Part Number: 1183 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for 12-Volt negative

More information

MSD Digital 6 Plus Ignition Control PN 6520

MSD Digital 6 Plus Ignition Control PN 6520 INSTALLATION INSTRUCTIONS 1 MSD Digital 6 Plus Ignition Control PN 6520 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug

More information

Dual Fire Capacitor Discharge Ignition

Dual Fire Capacitor Discharge Ignition Dual Fire Capacitor Discharge Ignition Page 1 Dual Fire CDI Instruction Manual VERSION 1.0 Warning Please ensure all power supplies are disconnected before commencing work. This product produces high voltages.

More information

Suggested Installation Instructions for: , Ignitor Conversion Kit

Suggested Installation Instructions for: , Ignitor Conversion Kit Suggested Installation Instructions for: 609-421, 1958-1974 Ignitor Conversion Kit INSTALLATION INSTRUCTIONS FOR DELCO 8 & 6 DISTRIBUTORS 1181 1164 Refer to "pre-installation checks" on back page before

More information