Usage Instructions of Solar Control for 3Way-Ball Valve
|
|
- Stephany Mathews
- 6 years ago
- Views:
Transcription
1 Table of Contents: Page: 2 Safety Instructions 3 Intended Use / General / Warranty / Installation: 4 Schematic Diagram: Mounting the sensor 5 Start-UP 6 Note: 7 Electrical connections: Technical Specifications 8 Connection types 9 Parts catalog 10 Dimensions: Failure Cause: In the event of damage arising out of the non-compliance with the present Instructions for Use or if lead- sealed parts have been tampered with, the warranty furnished shall become void. We do not assume any liability for consequential damage. Prior to using the equipment, please read the present Instructions for Use thoroughly. PRECISION RESULTS INNOVATION - PRODUCTION Seite- 1 -
2 Safety Instructions: This device was built and tested in conformity with the safety provisions for electronic equipment and has left our factory in a flawlessly safe and secure condition. To preserve such condition and ensure a perfectly safe operation, the user shall observe the Safety Instructions and the Instructions of Use. The required fitting work may be carried out only by a duly qualified and licensed fitter or electrician. Caution when working on house roofs. These may only be done when all safety regulations are preserved. Use antifall guard! The required electrical installation work shall be executed in conformity with the respective local and regional standards (e.g. ÖVE, VDE..) and, where applicable, with the relevant regulatory provisions. For the electrical connection, it is necessary to install a disconnector unit in the fixed electrical installation, making it possible to disconnect all poles of the electrical connection, with a contact gap of at least 3 mm from the main supply. Make sure that the supply voltage is fused properly and that a 30mA residual-current Circuit-breaker has been installed. Use the device in dry rooms only where no flammable gasses and vapours may exist. Do not start using the device immediately after it has been brought from a cold into a warm room. Otherwise, the condensation water might destroy it. If the device shows visible damage, no longer functions or has been stored in adverse conditions for an extended period of time, it must be assumed that it is no longer safe to use. In such case, the device must be secured against its unintended activation and, where necessary, be shut down. Prior to opening the body pull the plug. The motor electric is not galvanically separated from the mains. Opening its cover panels or removing components from it may cause energized components to become exposed. Prior to calibrations, maintenance jobs, repairs or the exchange of components or modules, the device must be disconnected from all voltage sources if opening the device is necessary. If, following such opening, a calibration, a maintenance job or a repair on the energized device is unavoidable, this may only be done by a skilled specialist who is aware of the related hazards and the relevant rules and provisions. Capacitors contained in the device may still be charged, even if the device has already been disconnected from all voltage sources. Carry out any assembly and disassembly of the valve only in the depressurized state (drain the pipe line first) Please consider flow direction in the valve Mount the ball valve according to the attached examples in the piping system and take care of the flow direction! PRECISION RESULTS INNOVATION - PRODUCTION Seite- 2 -
3 Intended Use: The control unit will bring your pool water to the preset temperature via the collectors (absorbers), provided that the available solar irradiation is sufficient. Any use other than the intended one is not allowed! General: PRAHER solar controls are technologically advanced products that are manufactured with high precision and according to the most up-to-date production methods. Should nevertheless justified complaints exist, these are being resolved by us as quick as possible. Warranty: In case there is a justified complaint always tells us the PRAHER serial number of the valve (number is laser printed in the lid). We do reserve the right for technical modifications in the light of the improvement of our products without giving any notification. For this device a warranty period according to the valid EU regulations applies. The day the product is delivered shall be deemed as the beginning of the warranty period.! All important parts are sealed!! Damaged sealed parts lead to expires of the warranty Installation: The device is delivered ready-to-plug-in and therefore does not have to be opened by customer prior to use. For installation and wiring we recommend separate cable ducts. These must not be laid together with the motor wiring. Should an extension of the cable be necessary, cut the cable at the correct spot and extend by using a clamp distributor up to max. 30m with 1,5mm² cross section. Both temperature sensors are galvanically separated from the main voltage. The device works in every position, however, it is recommended not to mount it actuator facing downwards. PRECISION RESULTS INNOVATION - PRODUCTION Seite- 3 -
4 Schematic Diagram: Rot While mounting the sensors take care that the relative sensor should be located as close as possible to the medium (for example water)! Red Blue Blau SC03 M Mounting the Pool sensor (Blue): Mount the pool sensor as closes to the pool as possible. De-pressurise the piping system and empty thoroughly.. 10mm Mounting the Collector sensor (Red): drill O-Ring, sealing element Mount the Collector sensor (red) as close as possible to the manifold of the collector and make sure that the collector sensor is exposed to direct solar radiation and can not be manipulated by the shade (i.e. trees, buildings). If shade interferes, the solar radiation cannot be used to the maximum. CAUTION: Due to the arrangement of the sensors in the system slight difference between the setand the real Pool temperature may occur. PRECISION RESULTS INNOVATION - PRODUCTION Seite- 4 -
5 Start-UP: After plugging in the control unit the GEEN - LED [1] for POWER (in operation) is illuminated; the device is ready for operation. The ball valve operates on position 1 The terminals [a - b] are open. (Flow direction of the pool water) If the pool temperature sinks by more than 1,5 C be low the set pool temperature [3] and the collector temperature rises by more than 4 C above the pool temperature [3], the valve automatically switches over to heating and turns to position 2. The RED - LED [2] is illuminated. The terminals [a - b] are switched through. (Flow direction of the pool water) [1] Control LED POWER [2] Control LED HEATING [3] Potentiometer Setting Temperature [4] Serial number [5] Hand emergency manipulation, optical position indication PRECISION RESULTS INNOVATION - PRODUCTION Seite- 5 -
6 NOTE: It is possible to reverse the position of the ball valve at solar operation for system-dependent appliances! Just switch over the inside slide switch from S1 to S2. See schematic diagram. Normal Operation (Delivered like this) Special Operation S2 S1 S2 S1 Schematic diagram at solar operation slide switch on S1: Schematic diagram at solar operation slide switch on S2: PRECISION RESULTS INNOVATION - PRODUCTION Seite- 6 -
7 Electrical connections: Usage Instructions Supply voltage: L1 N 12-34V DC V AC 50/60Hz Potential freely output: a b Zero potential I max. 300mA/250 VAC Zero potential: Switches at solar operated, for control solar pump, externally controls Filter clock override e.g. CS100, CS300 Technical Specifications: Voltage: 12-34VDC VAC 50/60Hz Power consumption: max.1,5 Watt 12-34V DC max. 60 Watt V AC 50/60Hz Protection rate: IP 54 Ambient temperature: max. 0 C 50 C Temperature difference Between Pool- and Collector sensor: Hysteresis pool temperature: max. 1,5 C T approx 4 C. This product complies to following EU- Guidelines: Electromagnetic Compatibility 89/336/EEC Low voltage guideline 73/23/EEC EMV ÖVE EN EN EN EN EN PRECISION RESULTS INNOVATION - PRODUCTION Seite- 7 -
8 Connection types: Usage Instructions Operate a solar pump: Filter clock override: PRECISION RESULTS INNOVATION - PRODUCTION Seite- 8 -
9 Parts catalog: Spare Parts List Pos. Part Description Ref. No. 1 Actuator 6V DC MVO Circuit board EO510,12-230V AC/DC Pool sensor (Blue) Collector sensor (Red) Available on request PRECISION RESULTS INNOVATION - PRODUCTION Seite- 9 -
10 Dimensions: DN d D C Y H I E A Z t mm , ,5 220, ,0 162,0 169,0 27,5 mm , ,5 220, ,0 162,0 171, Failure Cause: POWER LED is not illuminated: - check supply voltage - is the device plugged in? Pool water is not warming at solar operation: - filter pump is switched off Control unit does not switch to heating operation: - Sensor is not optimally located or defect Control unit does not end the heating operation: - Sensor is not optimally located or defect PRAHER VALVES Tel.: ++43 / (0) / * Fax: ++43 / (0) / austria@praher.com ; PRECISION RESULTS INNOVATION - PRODUCTION Seite- 10 -
11 PRECISION RESULTS INNOVATION - PRODUCTION Seite- 11 -
USE AND INSTALLATION HANDBOOK
Date : 10/02/14 Rev. 01 PR.T : FG006172 USE AND INSTALLATION HANDBOOK DUPLEX-UP CONTROL PANEL FOR 2 ELECTRIC PUMPS WITH CURRENT CONTROL. DUPLEX-UP Via Enrico Fermi 8-35020 Polverara PD Tel.049/9772407
More informationPURE SINE WAVE DC TO AC POWER INVERTER
PURE SINE WAVE DC TO AC POWER INVERTER 60S-12A / 60S-24A 60S-12E / 60S-24E 100S-12A / 100S-24A 100S-12E / 100S-24E 150S-12A / 150S-24A 150S-12E / 150S-24E Instruction manual SINE WAVE INVERTER Please read
More informationDC Master 24/ A
USERS MANUAL DC Master 24/12 50-60A DC-DC converter MASTERVOLT Snijdersbergweg 93, 1105 AN Amsterdam The Netherlands Tel.: +31-20-3422100 Fax.: +31-20-6971006 www.mastervolt.com ENGLISH Copyright 2015
More informationRevision THERMO TECHNOLOGIES. USDT 2001 Differential Controller. Installation and User s Guide
Revision 8 THERMO TECHNOLOGIES USDT 2001 Differential Controller Installation and User s Guide USDT 2001 DIFFERENTIAL CONTROLLER Installation and User s Guide Table of Contents Introduction General Information
More informationDemand Switch NEFA20 Plus. Installation Guide. Please read this entire guide before beginning the installation!
Demand Switch NEFA20 Plus Installation Guide Please read this entire guide before beginning the installation! Supplied Parts Protective Covers DIN Mounting Rail NEFA20 Plus Mounting Rail Spacer Warning
More informationUSER S MANUAL. Installation, Operation, & Maintenance
1-800-899-0553 assuredautomation.com SM Series Motorized Ball Valves On/Off & Modulating Electric Actuators USER S MANUAL Installation, Operation, & Maintenance Assured Automation 263 Cox Street, Roselle,
More informationOwner s Manual GLASSLINED PUMP TANK
Owner s Manual GLASSLINED PUMP TANK ANSI/NSF 61 Annex G Thank You for purchasing a pump tank. Properly installed and maintained, it should give you years of trouble free service. If you should decide that
More informationSolenoid Valve DF-SB-series
2/2-WAY SEMI-DIRECT OPERATED NORMALLY OPEN Solenoid Valve DF-SB-series The DF-DB is a semi-direct operated 2/2-way solenoid valve. The valve is normally open. The solenoid valves have an orifice of 16
More informationOPERATING INSTRUCTIONS
100% recy-cling paper Bleached without chlorine GB Imprint These operating instructions are published by Conrad Electronic GmbH, Klaus- Conrad-Str 1, 92240 Hirschau/Germany No reproduction (including translation)
More informationCompact System NRGS 11-2 NRGS Original Installation Instructions English
Compact System NRGS 11-2 NRGS 16-2 EN English Original Installation Instructions 810366-05 1 Contents Important Notes Page Usage for the intended purpose...4 Safety note...4 LV (Low Voltage) Directive
More informationHST-BL-2830MS & HST-BL-2830MS-USA
HST-BL-2830MS & HST-BL-2830MS-USA Release date: 02/2017 High - System - Technik Im Martelacker 12 D-79588 Efringen-Kirchen Phone 0 76 28-91 11-0 Fax 0 76 28-91 11-90 E-Mail: info@hs-technik.com Web: www.hs-technik.com
More informationSBS Manual for the specialised craftsman. Filling and flushing station. Connection Operation. en Manual
SBS 2000 Filling and flushing station Manual for the specialised craftsman Connection Operation Thank you for buying this RESOL product. Please read this manual carefully to get the best performance from
More informationOil-free piston compressors KK and piston vacuum pumps KV
Oil-free piston compressors KK and piston vacuum pumps KV Installation and Operating Instructions 0678106030L02 1707V003 Contents Important information 1 About this document 2 1.1 Warnings and symbols
More information2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE
2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE For Diaphragm Dosing Pumps FEM 1.02_.55 / FEM 1.09_.55 Controller board package, without pump: ID 160536 Operating and Installation Manual It is important to
More informationOperating instructions Safety sensor BNS About this document. Content. 6 Disassembly and disposal 6.1 Disassembly Disposal...
Safety sensor BNS Disassembly and disposal. Disassembly..... Disposal... EU Declaration of conformity Operating instructions.............pages to Original x.000 / 0.0 / v.a. - 09009- / J / 0-0-0 / AE-Nr.
More informationMANUAL. Single charger
MANUAL Single charger HST-PR-2830 & HST-PR-2830USA for HS-Technik batteries HST-PR-18xx HST-PR-14xx issue date: November 2016 Table of contents Page 1. Basic information...3 1.1. Purpose of this document...3
More informationOperations Manual. Zero Speed Switch Sensor Model ZS09P
Zero Speed Switch Sensor Model ZS09P The must be referred to for correct installation. Failure to comply with the shall void all warranties and liabilities. Overview The Phares Electronics Model ZS09P
More informationSoftstarter SAS SAS 11PUST, 22PUST Assembly- and Commissioning Instructions
electronic Softstarter SAS 3...11 SAS 11PUST, 22PUST Assembly- and Commissioning Instructions Quality is our Drive. SAS 3...11, SAS 11PUST, 22PUST 1 Stand 03/17 10800.10002 Table of contents Page 1. Safety
More informationHOME CHARGER MODE 2. Series to /32A single phase CONTENTS. Manual IMPORTANT SAFETY INSTRUCTIONS 3 SAFETY INFORMATION 4 INSTALLATION 5
CONTENTS IMPORTANT SAFETY INSTRUCTIONS 3 SAFETY INFORMATION 4 INSTALLATION 5 OPERATION 8 SPECIFICATIONS 8 MAINTENANCE 9 HOME CHARGER MODE 2 Series 31328 to 31340 16/32A single phase FCC INFORMATION 9 WARRANTY
More informationAXIAL FANS Axis / Tubo OPERATION MANUAL
TUBO-M AXIS-QA AXIS-Q AXIS-QR AXIS-F AXIS-QRA AXIAL FANS Axis / Tubo OPERATION MANUAL Axis / Tubo www.blaubergventilatoren.de CONTENT 3 Introduction 3 General 3 Safety rules 3 Transport and storage requirements
More informationUSER MANUAL GEBRUIKSAANWIJZING GEBRAUCHSANWEISUNG SKYLLA 24/100 3-PHASE CE
USER MANUAL GEBRUIKSAANWIJZING GEBRAUCHSANWEISUNG SKYLLA 24/100 3-PHASE CE SECTIONS: ENGLISH 2 NEDERLANDS 17 DEUTSCH 37 Victron Energy BV De Paal 35 1351 JG Almere-Haven The Netherlands Article number
More informationRE-PR1-F 1-Phase Din-Rail Mount 1.5, 3 & 6kW
Page 1 of 5 RE-PR1-F 1-Phase Din-Rail Mount 1.5, 3 & Features: Benefits: 0-10Vdc or 0-5Vdc control input Over temperature protection with auto reset Din-rail mounting Efficient electronic switching No
More informationKompensator External Low Voltage Heating Cable System
External Low Voltage Heating Cable System LOW VOLTAGE Installation Instructions General Information Kit Contents Qty Description 1 heating cable at pre-determined length Table of Contents General Information........................
More informationMODEL A96 SERIES. 130Vdc Switchmode Utility Rectifier / Battery Charger. Used with LaMarche Power Cage ECN/DATE
MODEL A96 SERIES 130Vdc Switchmode Utility Rectifier / Battery Charger Used with LaMarche Power Cage CPN112138 ECN/DATE ISSUE DATE: ECN 17010-12/05 106 BRADROCK DRIVE DES PLAINES, IL. 60018-1967 (847)
More informationDeclaration of Conformity
Declaration of Conformity We, Manufacturer: Spartanics Ltd. 3605 Edison Place Rolling Meadows, Illinois 60008 Phone: 847-394-5700 Fax: 847-394-0409 USA ENGLISH declare under our sole responsibility that
More informationVITA ZYrcomat. Operating manual Date of issue: 01-05
VITA ZYrcomat Operating manual Date of issue: 01-05 Teeth Veneering Materials Vita System Service 3D - Master Equipment All-Ceramics 2 T a b l e o f C o n t e n t s 1 Technical information...4 1.1 General
More informationWELDING INVERTER. PEGAS 160 E Smart PEGAS 200 E Smart OPERATING MANUAL. ALFA IN a.s. PEGAS E Smart Manual EN 04
WELDING INVERTER PEGAS 160 E Smart PEGAS 200 E Smart OPERATING MANUAL PEGAS 160-200 E Smart Manual EN 04 2/12 CONTENT: 1. INTRODUCTION... 3 2. SAFETY INSTRUCTIONS AND WARNINGS... 4 3. TECHNICAL DATA...
More informationSolenoid Valve DF-SA-series
2/2-WAY SEMI-DIRECT OPERATED NORMALLY CLOSED Solenoid Valve DF-SA-series The DF-DA is a semi-direct operated 2/2-way solenoid valve. The valve is normally closed. These valves have an orifice of 16 to
More informationOwners Manual: - Pumps
Owners Manual: - Pumps GENERAL SAFETY RULES 1. The products mentioned in this manual are specially designed for the pre-filtering and re-circulation of water in swimming pools and spas. 2. They are designed
More informationOperation & Service Manual
Operation & Service Manual Model: 08-4048-0013 05/2008 - Rev. 01 Includes Illustrated Parts List 1740 Eber Rd Tronair, Inc. Phone: (419) 866-6301 Holland, OH 43528-9794 www.tronair.com 800-426-6301 USA
More informationMICROCARE 3 PHASE INVERTER MANUAL
3 PHASE INVERTER MANUAL 1 Contents 1. INTRODUCTI... 3 2. SAFETY INSTRUCTI... 4 3. SYSTEM DESCRIPTI... 6 4. WIRING DIAGRAM... 9 5. INVERTER OPERATI... 10 6. INVERTER CLUSTER PROGRAMMING... 13 7. CLUSTER
More informationPD404-AN V analog control 4 Channel x 500 W Dimmer & Switch Packs ANALOG 0-10 V. Serial Number
0-10V analog control 4 Channel x 500 W Dimmer & Switch Packs ANALOG 0-10 V 4 circuit Analog 1-10V 4 x 4 A. Dimmer pack Serial Number Dimmers Indicators Digital Lighting Systems,Inc Info@digitallighting.com
More informationWilo-Control SC-Fire Jockey
Pioneering for You Wilo-Control SC-Fire Jockey de en fr Einbau- und Betriebsanleitung Installation and operating instructions Notice de montage et de mise en service nl Inbouw- en bedieningsvoorschriften
More informationCAUTION CM-SE CM-S21 CM-S41
CAUTION Safety, Technology & Innovation CM Series Operating Instructions for, CM-S21,, CM-S11, CMS31 CM Series Safety System This information is designed to help suitably qualified personnel install and
More informationMounting and Operating Instructions EB 5868/5869 EN
Electric Control Valves Types 3213/5857, 3213/5824, Types 3214/5824, 3214/3374, 3214/3274 with safety function: Types 3213/5825, 3214/5825, 3214/3374, 3214/3274 Pneumatic Control Valves Types 3213/2780-1,
More informationGRUNDFOS INSTRUCTIONS. Grundfos ALPHA Installation and operating instructions
GRUNDFOS INSTRUCTIONS Grundfos ALPHA Installation and operating instructions LIMITED WARRANTY Products manufactured by GRUNDFOS PUMPS CORPORATION (Grundfos) are warranted to the original user only to be
More informationSMART ENERGY SAVER Manual
SMART ENERGY SAVER Manual PLEASE READ CAREFULLY BEFORE INSTALLING OR USING SMART ENERGY SAVER. THIS UNIT SHOULD ONLY BE INSTALLED AS SUPPLIED (AS A PLUG AND PLAY UNIT) IF YOU HAVE PURCHASED THE HARD WIRED
More informationInstallation Instructions: K-Safe-T-Drift
Micro Switch Installation Sheet Micro Switch Cam Rest Position See Vertical or Horizontal Arm Installation Instructions for Micro Switch activation sequence. Micro Switch Cam Adjustment Screw SW 1 Micro
More informationRE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW
Page 1 of 6 3-Phase Panel Mount 86 and 105kW Features: Benefits: 0-10Vdc, 0-5Vdc, 4-20mA or manual via potentiometer control input Over temperature protection with auto reset Enclosed panel mounting Efficient
More informationCentral Inverter SUNNY CENTRAL 500CP-JP / 500CP XT / 630CP XT / 720CP XT / 760CP XT / 800CP XT / 850CP XT / 900 CP XT
Central Inverter SUNNY CENTRAL 500CP-JP / 500CP XT / 630CP XT / 720CP XT / 760CP XT / 800CP XT / 850CP XT / 900 CP XT Maintenance Manual SCCP-WH-B4-en-20 98-4046720 Version 2.0 EN SMA Solar Technology
More informationHANGKAI GROUP HOYMILES MICRO-INVERTER MI-250
HANGKAI GROUP HOYMILES MICRO-INVERTER MI-250 TECHNICAL MANUAL CONTENTS INTRODUCTION... 3 SAFETY... 4 SYMBOL ILLUSTRATION... 4 INSTALLATION WARNINGS... 6 PREPARE FOR INSTALLING... 7 TRANSPORT AND INSPECT...
More informationEV-2051-M Electric Motor. Operation and Maintenance Manual
EV-2051-M Electric Motor Operation and Maintenance Manual Table of Contents Safety... 3 General...3 Safety Notices...6 Cautions, Warnings and Dangers...7 Cautions...8 Warnings...11 Dangers...13 Important
More informationUL AND CODE COMPLIANCE
BAL500 FLUORESCENT EMERGENCY BALLAST 500 Lumens APPLICATION The BAL500 fluorescent emergency ballast works in conjunction with the AC ballast to convert new or existing fluorescent fixtures into emergency
More informationMWR Reamer 08/01/2010
MWR Reamer 08/01/2010 Operating Instructions and Spare Parts List Torch Nozzle Cleaning Device for Robotic Mig Welding System Registration Purchaser: Address; City State Zip Phone: Email: Contact: Purchased
More informationCopyright 2012 DelSolar Co. Ltd MQWRD installation manual-iec Ver. 1.4
INSTALLATION MANUAL IEC Version www.delsolarpv.com Copyright 2012 DelSolar Co. Ltd MQWRD-01-14--installation manual-iec Ver. 1.4 Content General information 1 Safety precaution for installing solar PV
More informationOperating Instruction Manual for Energy Management System EBL 99 C, Art.-Nr Seite 1 / 7
EBL 99 C, Art.-Nr. 911.413 Seite 1 / 7 Contents 1. Description 2. Safety Information 3. Operating Instructions 4. Transport, Storage, Installation 5. Electrical Installation 6. Power-Up, Shut-Down, Maintenance
More information20 amps 220 amps, 60 Hz VDC VAC G3PA-420B-VD-2 DC amps 440 amps, 60 Hz G3PA-450B-VD-2 DC12-24
Solid State Relays (SSRs) G3PA/G3PB Long Service Life for Circuits that Cycle Frequently D D D D D Built-in heat sink increases life and reliability Voltage turn-on at zero crossing reduces initial inrush
More informationOperation and Maintenance Manual for Multipurpose Actuators. 120 VAC Actuator 12 VDC Actuator 12 VDC Actuator
Joyce/Dayton Corp. Operation and Maintenance Manual for Multipurpose Actuators 120 VAC Actuator 12 VDC Actuator 12 VDC Actuator The recommendations in this manual for installation, operation and maintenance
More informationMICRO-INVERTER OMNIKSOL M-300
MICRO-INVERTER OMNIKSOL M-300 TECHNICAL MANUAL CONTENTS INTRODUCTION... 3 SAFETY... 4 SYMBOL ILLUSTRATION... 4 INSTALLATION WARNINGS... 6 PREPARE FOR INSTALLING... 7 TRANSPORT AND INSPECT... 7 CHECK INSTALLATION
More informationStarEye. 350 ma version. No control electronics on board
StarEye 350 ma version No control electronics on board CONTENT 1 PICTURE... 3 1.1 GENERAL... 3 2 DIMENSIONS... 4 3 SAFETY INFORMATION... 5 3.1 SYMBOLS... 5 3.2 PROTECTION FROM ELECTRIC SHOCK... 6 3.3 PROTECTIONS
More informationGEIGER-GJ56.. with mechanical end stop For Venetian blinds and exterior blinds
Venetian blind motor: GEIGER-GJ56.. with mechanical end stop For Venetian blinds and exterior blinds DE FR ES IT Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice
More informationApplicable output load (See note 2.) Photocoupler Yes Yes 40 A at 110 to 220 VAC 5 to 24 VDC G3NB-240B 5 to 24 VDC G3NB-240B-UTU 5 to 24 VDC
Solid State Relays G3NB with 40-A output at a reasonable price. Switches 9 A without a heat sink. Zero cross function enables less noise operation. Built-in varistor effectively absorbs external surges.
More informationECONOMISER SERIES E2T USER MANUAL
TURBO S.R.L. Electronic Control Systems for Dust Collectors e-mail: info@turbocontrols.it web: www.turbocontrols.it TEL. ++39 (0)362 574024 FAX ++39 (0)362 574092 ECONOMISER SERIES E2T USER MANUAL 24/06/2014
More informationSOLAR SPOT Installation Guide
SOLAR SPOT Installation Guide GUANGDONG GOLDEN GLASS TECHNOLOGIES LIMITED Add: Diejin Enterprise District, Shantou University Road, Shantou, Guangdong, P.R.China Tel: (86)754-8253 4593 Fax:(86)754-8253
More informationQSI (Q-Star) Electronics Owner s Manual
QSI (Q-Star) Electronics Owner s Manual QSI Module (Installs in Plain Cover Plate) QSI2 Shown QSI Module (Installs in Display Mount Cover Plate) QSI2 Shown TABLE OF CONTENTS INTRODUCTION... 2 IMPORTANT
More informationMINICHARGER. User Manual and Safety Instructions. Version 20/12/2016
MINICHARGER User Manual and Safety Instructions Version 20/12/2016 CONGRATULATIONS! You have just acquired a MINICHARGER and we thank you! This product is designed and conceived in France, with the collaboration
More informationULTRASONIC FLOW SENSOR QALCOSONIC FLOW 2
AB AXIS INDUSTRIES ULTRASONIC FLOW SENSOR QALCOSONIC FLOW 2 TECHNICAL DESCRIPTION, INSTALLATION AND USER INSTRUCTIONS PESF2V01 KAUNAS Contents Page SAFETY INFORMATION... 1. APPLICATION FIELD... 2. TECHNICAL
More informationModel Number Structure
Solid State Relays (Single-phase) G3PB New Single-phase Solid State Relays with Compact Size for Heater Control Slim models with a thickness of only 22.5 mm are also available. Compact design achieved
More informationModel LA 4400 Time Delay OFF Controller
ISIMET LA Series Model LA 4400 Time Delay OFF Controller Installation, Operation and Maintenance Manual Application: The Time Delay OFF Controller with integral 24-hr. programmable time clock operates
More informationBefore installing this unit, read the operating instructions carefully. Strictly adhere to these operating instructions.
Instruction Manual ENGLISH Before installing this unit, read the operating instructions carefully. Strictly adhere to these operating instructions. BIBO QUICK START GUIDE Insert the bibo Mouthpiece into
More informationBraking Devices BR 230/ Assembly- and Commissioning Instructions
electronic Braking Devices BR 230/400-10...400 Assembly- and Commissioning Instructions Quality is our Drive. BR 230/400-10...400 1 as per 04/10 11600.10001 Table of Contents Page 1. Safety notes 3 2.
More informationInstallation Manual. Mixing Box Control Systems Installation, Operation, and Maintenance Manual. 605 Shiloh Road Plano, Texas
Installation Manual IOM-MBC-00 08-30-04 Mixing Box Control Systems Installation,, and Maintenance Manual Contents Page Introduction...1 General...1 Safety...1 Inspection...1 Mixing Box Control Systems...2
More informationMODEL A97 SERIES. Switchmode Utility Rectifier/Battery Charger ECN/DATE
MODEL A97 SERIES Switchmode Utility Rectifier/Battery Charger CPN108172 ISSUE DATE: 16071 7/03 ECN/DATE 106 BRADROCK DRIVE DES PLAINES, IL. 60018-1967 (847) 299-1188 FAX: (847)299-3061 Page 1 of 7 INSTRUCTION
More informationSolar Thermal. Grant Solar Pump Station Installation & Servicing Instructions
Solar Thermal Grant Solar Pump Station Installation & Servicing Instructions Part No. DOC 96. Rev 02. October 2012 Important Note Important Note for Installers The Pump Station supplied with your Grant
More informationRS-3 PRO RS-1007 PRO. CAT IV Analog Clamp meter Series. Users Manual. For detailed specifications and ordering info go to
RS-3 PRO RS-1007 PRO CAT IV Analog Clamp meter Series Users Manual For detailed specifications and ordering info go to www.testequipmentdepot.com RS-3 PRO RS-1007 PRO CAT IV Analog Clampmeter Series English
More informationINSTALLATION AND MAINTENANCE MANUAL FORM #PM-126 REV A 12/09
HAND CRANK & MOTORIZED POWER CORD REELS: SERIES 1125PC SERIES: 1125PC HAND CRANK SERIES: 1125PC MOTORIZED COXREELS The technical data and images which appear in this manual are for informational purposes
More informationMICRO SWITCH INSTALLATION SHEET
MICRO SWITCH INSTALLATION SHEET Micro Switch Cam Rest Position See Vertical or Horizontal Arm Installation Instructions for Micro Switch activation sequence. Micro Switch Cam Adjustment Screw SW 1 Micro
More informationGEIGER-SOLIDline* GEIGER-Touch (GU45..M) for rolling shutters, awnings and screens. Bedienungsanleitung. Operating Instructions. Manuel d utilisation
Tubular motor: GEIGER-SOLIDline* Motor control: GEIGER-Touch (GU45..M) for rolling shutters, awnings and screens DE Bedienungsanleitung Operating Instructions FR Manuel d utilisation ES Manual de instrucciones
More informationMV Series Motors Operation & Parts Manual
MV Series Motors Operation & Parts Manual Models M3V, M5V, M5V-US For use with M3V s/n 101057 & below, M3V-UK s/n 103013 & below, M5V & M5V-US s/n 102972 & below. EU Declaration of Conformity Finish Thompson
More informationDeltaSol AX * *
DeltaSol X Differtial temperature controller Manual for the specialised craftsman Installation Operation Functions and options Troubleshooting *48000250* 48000250 Thank you for buying this RESOL product.
More informationInstallation Manual LIGHTWAY PV MODULES. Revision Date March 30, 2013 /Applicable for IEC certified products
LIGHTWAY PV MODULES Installation Manual Lightway Green New Energy Co.,Ltd. New Industry Park,Gaobeidian,Hebei Province,China Tel:0086-(0)312-2951177 Fax:0086-(0)312-2951166 www.lightwaysolar.com Thank
More informationFiltered PWM Speed Control for Permanent Magnet DC Motors
Instructions for Installation and Operation Filtered PWM Speed Control for Permanent Magnet DC Motors Model 0794 Speed and Direction Control up to 5/8 HP NEMA-1/IP-20 Specifications Product Type:... WPM-2148E1
More informationA Member of the. Integrated Metering Technologies
I n s t a l l a t i o n M a n u a l A Member of the Integrated Metering Technologies 1.0 General and safety Do not install, operate or maintain this flow meter without reading, understanding and followingthe
More information99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Instruction Manual. Model 2831D 4 ½ Digit True RMS Digital Multimeter
99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com Instruction Manual Model 2831D 4 ½ Digit True RMS Digital Multimeter 1 1. PRODUCT DESCRIPTION 1-1. Introduction Thank you
More informationA408 GB. Pneumatic oil and diesel pumps 1:1
03 594 A408 GB Pneumatic oil and diesel pumps 1:1 G Operating instructions for Pneumatic oil and diesel pump 1:1 Contents 1. General details 2 1.1 Intended use 2 1.2 Design and functional description 2
More informationA Member of the. Integrated Metering Technologies
I n s t a l l a t i o n M a n u a l A Member of the Integrated Metering Technologies 1.0 General and Safety Do not install, operate or maintain this flow meter without reading, understanding and followingthe
More informationMODULATING SERVICE ELECTRIC ACTUATORS OPERATION AND MAINTENANCE MANUAL COMMERCIAL AND INDUSTRIAL VALVES AND AUTOMATION
SERIES 000/S-X MODULATING SERVICE ELECTRIC ACTUATORS OPERATION AND MAINTENANCE MANUAL COMMERCIAL AND INDUSTRIAL VALVES AND AUTOMATION Publication S000X- VER045- For information on this product and other
More informationDeltaSol AX. RESOL DeltaSol AX * * Mounting Connection Operation Application examples. manual
RESOL DeltaSol AX Mounting Connection Operation Application examples DeltaSol AX *48000250* 48000250 Thank you for buying a RESOL product. Please read this manual carefully in order to put this controller
More informationB2000 SERIES TACHOMETERS DIGITAL OR ANALOG DISPLAYS
B133-05, Page 1 952-361-3026 PROCESS CONTROL SYSTEMS, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 B2000 SERIES TACHOMETERS DIGITAL OR ANALOG DISPLAYS Introduction The
More informationElectromotoric Actuators
4 506 Electromotoric Actuators for valves with 90 angle of rotation operating voltage AC 230 V 3-position control signal Nominal angle of rotation 90 Auxiliary switch and potentiometer for extra functions
More informationGSL Electronics Modified Sine Wave Power Inverters
GSL Electronics Modified Sine Wave Power Inverters Congratulations on choosing one of our Modified Sine Wave Inverters for your application. There are 6 models in the range, which will meet most of your
More informationpowerdriveinverters.com Owner s Guide Please Save for Future Reference 300 Watt DC to AC Power Inverter
powerdriveinverters.com Owner s Guide Please Save for Future Reference 300 300 Watt DC to AC Power Inverter Thank you for purchasing the POWERDRIVE300 power inverter, a high performance solution to using
More informationRental Industry Safety Tester Safe Check 5s
Rental Industry Safety Tester Safe Check 5s Feb 2006 2006 Clare Instruments Inc. Issue 2.0 Firmware Version : 1.2a Limited Warranty & Limitation of Liability Clare Instruments Inc, guarantees this product
More informationSolid State Relays G3RV. Model Number Structure. Ordering Information. Model Number Legend. List of Models. SSR and Socket Combinations
Solid State Relays G3RV Slimmest OMRON plug-in SSR with maximum width 6.2 mm Long electrical life and high speed switching Large plug-in terminals for reliable connection G3RV-D (DC load) models can manage
More informationInstallation and Operating Instructions Magnetic Vibrator MR 1
Installation and Operating Instructions Magnetic Vibrator MR 1 (Translation of the Original Instruction Manual) Würges Vibrationstechnik GmbH Daimlerstraße 9 D-86356 Neusäß Telephone +49 821 999824-00
More informationIS7.6 INSTALLATION MANUAL
IS7.6 INSTALLATION MANUAL #12501 MIN. 13.5" 1" 1" 29-7/8" 3" 14-7/8" 3" 20-7/8" 29-7/8" 24-5/8" Fig. 1 1 2 Fig. 2 Fig. 3 MAX. 80" MIN. 12" IS7.6 MIN. 8" Fig. 4 2 MIN. 6" MIN. 13.5" MIN. 12" MIN. 6" MIN.
More informationRotary Valve Maxflo + 60 and 80 Opening type NT
Rotary Valve Maxflo + 60 and 80 Opening type NT TECHNICAL MANUAL 1- INSTALLATION 1.1 - Valve pipe-work layout 1.2 - Specification check 1.3 - Installing the valve in the piping 1.4 - Connection to control
More informationpowerdriveinverters.com Owner s Guide Please Save for Future Reference 100 Watt DC to AC Power Inverter
powerdriveinverters.com Owner s Guide Please Save for Future Reference 100 100 Watt DC to AC Power Inverter Thank you for purchasing the POWERDRIVE100 power inverter, a high performance solution to using
More informationIntelligent Battery Charger
Intelligent Battery Charger PA-NT2000 USER S MANUAL www.power-charger.net CONTENTS 1. Intended Use... 2 2. Delivery content... 3 3. Safety Instructions... 3 3.1Product Safety... 3 3.2 Battery safety...
More informationGUIDELINES ON ELECTRICAL SAFETY AT WORKPLACES
MINISTRY OF LABOUR, INDUSTRIAL RELATIONS AND EMPLOYMENT GUIDELINES ON ELECTRICAL SAFETY AT WORKPLACES Occupational Safety & Health Inspectorate These guidelines should be used with approved standards:
More informationTURBOTRONIK NT 151/361
Vakuum-Lösungen Applikations- Unterstützung Service LEYBOLD VAKUUM GA 05.214/7 TURBOTRONIK NT 151/361 Elektronischer Frequenzwandler Electronic Frequency Converter Kat.-Nr. / Cat. No. 857 15/16/17/18/19
More informationGEIGER-GJ5610v1 with mechanical end stop For Venetian blinds and exterior blinds for 100 V power supply
Venetian blind motor: GEIGER-GJ5610v1 with mechanical end stop For Venetian blinds and exterior blinds for 100 V power supply DE FR ES IT Original-Montage- und Betriebsanleitung Original assembly and operating
More informationOperation & Service Manual
Operation & Service Manual Model: 08-4049-1012 Includes Illustrated Parts Lists Tronair, Inc. 1740 Eber Road Holland, Ohio 43528-9794 USA Telephone: (419) 866-6301 800-426-6301 Fax: (419) 867-0634 Web
More information(with Class-1 AC resistive load) 3. G3PB-215B-2N-VD kW max. (25 A) G3PB-225B-3N-VD 2. G3PB-225B-2N-VD kw max. (35 A) G3PB-235B-3N-VD 2
Solid-state Contactor (New Heat Sink Construction) G3PB Space and working time saved with new heat sink construction. Series now includes 480-VAC models to allow use in a greater range of applications.
More informationOperating Instruction Manual of Energy Management System EBL 208, Art.-No Seite 1 / 7
EBL 208, Art.-No 911.430 Seite 1 / 7 Contents 1. Description 2. Safety Information 3. Operating Instructions 4. Transport, Storage, Installation 5. Electrical Installation 6. Power-Up, Shut-Down, Maintenance
More informationLED FlatPanel Gen. 2. LED FlatPanel Gen. 2 ULTRA FLAT LIGHT PANEL. LED FlatPanel Gen. 2
LED FlatPanel Gen. 2 ULTRA FLAT LIGHT PANEL LED FlatPanel Gen. 2 LED Recessed Mounted FlatPanels The use of state-of-the-art LED technology in conventional office and hall illumination provides a lot of
More informationElectronic Ballast EVG 2000-T
Electronic Ballast EVG 2000-T Operating Manual Table of contents 1 Description 1.1 Advantages of this ballast... 3 1.2 Functional principle... 3 1.3 Energization... 4 1.4 Visualization... 5 1.5 Indications
More informationFOR NEW ZEALAND. T-604 WASTE DISPOSER B. HYDRAULIC CHARACTERISTICS &TECHNICAL SPECIFICATIONS. DECLARATION OF COMPLIANCE
FOR NEW ZEALAND. T-604 WASTE DISPOSER B. HYDRAULIC CHARACTERISTICS &TECHNICAL SPECIFICATIONS. Maximum height of pumped discharge: 6 m Max. Graded distance of pumped discharge: 62 m : Location of power
More informationTIC 300 PRO. Users Manual Mode d emploi Bedienungshandbuch Manual d uso Manual de uso. Non Contact AC Voltage Detector. High Energy Tic Tracer
TIC 300 PRO High Energy Tic Tracer Non Contact AC Voltage Detector Users Manual Mode d emploi Bedienungshandbuch Manual d uso Manual de uso TIC 300 PRO High Energy Tic Tracer Non Contact AC Voltage Detector
More informationInstallation and Operation Instructions. VAG ROTOP Portable Electric Drive
Installation and Operation Instructions VAG ROTOP Portable Electric Drive KAT-B 5551 Edition 1-01/2018 Content 1 General 3 1.1 Safety 3 1.2 Proper use 3 2 Transport and Storage 3 2.1 Transport 3 2.2 Storage
More information