2005 / 2012 / 2035 Series

Transcription

1 005 / 0 / 035 Series Accessories Sandwich Pressure Regulators Accessory Description 0. to bar Regulator repair kit 0.3 to bar to 9 bar to bar Regulator repair kit 0.3 to bar to 9 bar to bar Regulator repair kit 0.3 to bar to 9 bar Elbow kit 39-7 Retaining clip Extension kit Gauge to max. bar -5 Gauge to max. bar Adapter, port G/ Retaining clip GB-008/R0 X0-7-6

2 Sandwich Speed Control 005 / 0 / 035 Series Spare Parts Sandwich Components Sandwich speed controls for valves and regulators are equipped with an integral plug-in system. Sandwich speed controls provide a variable restriction in ports 3 and 5 in order to control the cylinders extend and retract speed. To facilitate easy adjustment both screws are on the same side of the speed control. Note: Sandwich speed controls can only be used with single sandwich pressure regulators. Single Solenoid Pilot Actuated, 5-port., -pos. Valve Single Sandwich Pressure Regulator Plug-in System Sandwich Speed Control Stud Manifold Block Accessory Sandwich speed control Description Order code ISO ISO GB-0/R Shut-off sandwich plate - Only apply with internal pilot air. - Regulator and sandwich speed control must be mounted in the lowest position. - If used with regulator, only use with ES or ED regulator. - Regulated pressure >.8 bar. Sandwich pressure block - Used to supply a separate pressure to a single valve station without needing blocking disks. Sandwich exhaust block - Used to isolate the exhaust of a single valve station from the manifold. - Allows faster exhaust response by re-routing. - Exhaust externally to the manifold. Assembly/disassembly of bar: - 005: mm external hex key - 0 & 035:.5 mm external hex key X 5 3 XE X 5 3 XE X 5 3 XE 5 3 X 5 3 XE ISO ISO ISO ISO X0-7-7

3 005 / 0 / 035 Series Spare Parts Accessory Description Order Blank station plate (screw, blank station plate, O-ring, gasket) Blocking disks Cover for end plate Cover for end plate with muffler Gasket for end plate cover Muffler for end plate cover Plug for conversion of pilot supply 005 ISO ISO for port for port 3/ for port, 3/ screw cover screw cover screw cover screw cover screw right end cover left end cover screw cover DIN rail mounting Accessory Description Order Push-in fitting for ports, 3, 5 (0 mm) Push-in fitting for ports X, XE (6 mm) 3-99 Push-in fitting for ports, (6 mm) 3-53 Push-in fitting for ports, (8 mm) Blocking plug for ports, 3, Blocking plug for ports X, XE Blocking plug for ports, Push-in fitting for ports,, (8 mm) Interchangeable cartridge fittings Push-in fitting for ports,, Push-in fitting for ports X, XE (0 mm) ( mm) Push-in fitting for ports X, XE (6 mm) 3-99 Push-in fitting for ports 3, 5 ( mm) Push-in fitting for ports 3, 5 ( mm) 3-53 Blocking plug for ports,, Blocking plug for ports X, XE Blocking plug for ports 3, GB-008/R0 X0-7-8

4 005 / 0 / 035 Series Spare Parts End Plate Kits 005 Series End plate kit, supply ports on both sides, with thread End plate kit, supply ports on both sides, with push-in fittings End plate kits Weight Port 3/5 X/XE 3/5 X/XE approx. Size G 3/8 G 3/8 G /8 0 mm 0 mm 6 mm Without muffler, standard mount Without muffler, for DIN rail mounting With muffler, standard mount With muffler, for DIN rail mounting On request: with NPTF thread 0 Series End plate kit, supply ports on both sides, with thread End plate kit, supply ports on both sides, with push-in fittings 0096GB-008/R0 End plate kits with supply ports Port Weight -3/5-X/XE -3/5-X/XE Weight -3/5-X/XE Weight -3/5-X/XE on both ends Size approx. ISO8/-G 3/8-/-/8 NPTF 3/8-/-/8 approx. PUSH-IN 8--6 mm approx. PUSH-IN 0--6 mm Without muffler standard mount Without muffler for DIN rail mounting With muffler, standard mount With muffler, for DIN rail mount X0-7-9

5 005 / 0 / 035 Series Spare Parts End Plate Kits 0 Series End plate kit, supply ports on left side, with thread End plate kit, supply ports on left side, with push-in fittings End plate kits Port Weight -3/5-X/XE -3/5-X/XE Weight -3/5-X/XE Weight -3/5-X/XE Size approx. ISO8/-G 3/8-/-/8 NPTF 3/8-/-/8 approx. PUSH-IN 8--6 mm approx. PUSH-IN 0--6 mm LH ports without muffler LH ports w/o muffler, with DIN rail LH ports with muffler, w/o DIN rail LH ports with muffler, with DIN rail Series End plate kit End plate kits Weight Port 3/5 X/XE approx. Size / / /8 End plates with muffler End plates without muffler LH ports with muffler, RH mounting cover with pilot exhaust LH ports without muffler, RH mounting cover with pilot exhaust On request: with NPTF thread 0096GB-008/R0 X0-7-30

6 005 / 0 / 035 Series Spare Parts End Plate Kits ISO ISO 507-8mm Series End plate kit, supply ports on both sides, with thread End plate kit, supply ports on both sides, with push-in fittings End plate kits 8 mm Port Weight -3/5-X/XE -3/5-X/XE -3/5-X/XE Size approx. NPTF 3/8-3/8-/8 ISO8/-G 3/8-3/8-/8 PUSH-IN mm w/o muffler, w/o DIN rail w/o muffler, w/ DIN rail w/ muffler, w/o DIN rail w/ muffler, w/ DIN rail ISO 507-6mm Series End plate kit, supply ports on both sides, with thread End plate kit, supply ports on both sides, with push-in fittings End plate kits 6 mm Port Weight -3/5-X/XE -3/5-X/XE Weight -3/5-X/XE -3/5-X/XE Size approx. NPTF 3/8-/-/8 ISO8/-G 3/8-/-/8 approx. PUSH-IN 8--6 mm PUSH-IN 0--6 mm 0096GB-008/R0 w/o muffler, w/o DIN rail, , w/o muffler, w/ DIN rail, , w/ muffler, w/o DIN rail, , w/ muffler, w/ DIN rail, , End plate kit, supply ports on one side, with thread End plate kits 6 mm End plate kit, supply ports on one side, with push-in fittings Port Weight -3/5-X/XE -3/5-X/XE Weight -3/5-X/XE -3/5-X/XE Size approx. NPTF 3/8-/-/8 ISO8/-G 3/8-/-/8 approx. PUSH-IN 8--6 mm PUSH-IN 0--6 mm LH ports only Kit w/o muffler, w/o DIN rail 0, , LH ports only Kit w/o muffler, w/ DIN rail 0, , LH ports only Kit w/ muffler, w/o DIN rail 0, , LH ports only Kit w/ muffler, w/ DIN rail 0, , X0-7-3

7 Spare Parts Valves Valve Model Number 05 BB 00 M Series 05 = 005 Series = 0 Series 35 = 035 Series I5* = 005 Series ISO 507-8mm I6* = 0 Series ISO 507-6mm R5* () = 005 Series ISO 507-8mm R6* () = 0 Series ISO 507-6mm *see the symbols table bellow to verify compatibility with spool valves functions () rubber packed spool Port Size of Base = Valve w/o manifold X = Valve w/o manifold X 3 = Valve w/o manifold X Voltage 0 = / Hz 30 = 0 / Hz 60 = VDC 6 = VDC Options 000 = Without option B = Locking override M = Without manual override X = External pilot supply (only for series 0 with base options 3A + 3C) 56Y = mm Electrical connector (in conduit port of 0 series base mounting only) Further options on request BA = BB = BN = Actuator Single actuated and spring return flush non-locking manual override Double actuated, flush non-locking manual override ISO 507-: Single actuated and differential return, flush non-locking manual override Function = 5-port., -pos. valve X X X 5 = 5-port., 3-pos. valve, open center, dual pressure X X X 6 = 5-port., 3-pos. valve, closed center X X X 7 = 5-port., 3-pos. valve, connected with &, 3 & 5 blocked X X D = Dual 3-port., -pos. valve NC, NC X X E = Dual 3-port., -pos. valve NC, NC, vacuum service X Port Type of Bases 0 = Without base Wiring Options K = Plug-in, AC with LED M = Plug-in, DC with LED Mounting 00 = Valve unit only Ribbon cable option must be used for manifold assemblies that exceed 6 solenoids. (7th and 8th digit of valve order code) (please refer to explanations on page X0-7-3) I5/I //35... R5/R6... I5/I //35... I5/I //35... BA BN* BB BB5* 5-ported, -pos. valve, spring return 5-ported, monostable, differential return 5-ported, -pos. valve, detented 5-port., 3-pos. valve, open center, dual pressure Symbols R5/R //35... I5/I //35... R5/R //35... R5/R //35... BB6* BB7* BBD* BBE* 5-port., 3-pos. valve, closed center 5-port., 3-pos. valve, connected with &, 3 & 5 blocked Dual 3-port., -pos. valve NC, NC Dual 3-port., -pos. valve vacuum service NC, NC 0096GB-03/R0 X0-7-3

8 Sandwich Pressure Regulator Model Number Spare Parts Sandwich Pressure Regulators 05 ES 00 J Series 05 = 005 Series = 0 Series 35 = 035 Series I5 = 005 Series ISO 507-8mm I6 = 0 Series ISO 507-6mm Port Size of Base = Valve w/o manifold X = Valve w/o manifold X 3 = Valve w/o manifold X 000 = Standard H = 6N = 6P = 6W = 6Y = 63D = Without gauge Options Jumper on end Jumper on end Top facing gauge* (005 series) Extended gauge* (005 series) 6W + 6Y* (005 series) * see note below Further options on request O = Port Type of Bases Without base Regulator Type ES = Single pressure to port ED = Dual pressure to ports 3 and 5 EC = Dual pressure with non-relieving checks (0 and 035 series) EQ = Dual pressure with relieving checks (0 and 035 series) EE = Dual pressure to ports and ET = Two-pressure selector Wiring Option J = Plug-in receptacle Mounting = Regulator unit only X X = 0.7 to 9 bar 3 = 0. to bar Pressure Range = 0.5 to bar Ribbon cable option must be used for manifold assemblies that exceed 6 solenoids. (7th and 8th digit of valve order code) (please refer to explanations on page X0-7-3) 0096GB-009/R0 5 3 Single pressure from a single supply Symbols ES ED EC EQ (0-035) Relieving: exhausts pressure in cylinder if upstream pressure is exhausted Dual pressure from a single supply 5 3 EE 5 External outlet regulator used with jumper plate for single or dual pressure (0-035) Non-relieving: taps downstream pressure if upstream is exhausted 5 3 ET Two-pressure selector used for multi-pressure applications Note (005 series): Regulator gauges must be offset on alternating stations to prevent interference (see photo) Odd numbered stations will use either standard (no option) or top facing ( 6W option) gauges. Even numbered stations will use either extended standard ( 6Y option) or extended top facing ( 63D option) gauges. X0-7-33

9 005 / 0 / 035 Series Spare Parts Manifold Assembly Kits Z-Boards Z-Boards 005 Series includes different Z-Boards for driving up to 3 solenoids of single and double solenoid actuated valves. Ribbon cable feature must be used for manifold assemblies that exceed 6 solenoids. In order to allow the full capacity of 3 solenoids, the assembly must be configured so that an even number of solenoids is utilised prior to the station using the ribbon cable feature. Note: The 6th and 7th solenoid cannot be on the same valve. (See valve model number selection for 7th and 8th digit for valve with 7th solenoid). Manifold Assemblies 005 Series Manifold assemblies Weight * with bottom ports Side ports in G /8 or / approx. G /8 NPTF /8 6 mm push-in 8 mm push-in With single Z-Board ** With double Z-Board ** With single Z-Board and ribbon cable ** With double Z-Board and ribbon cable ** * Manifold assemblies with adapter to ISO 507-, see following page. ** Bottom ports G / 0 Series Manifold assemblies * with bottom ports Weight Side ports in G / or NPTF approx. G / NPTF / G 3/8 NPTF 3/8 8 mm push-in 0 mm push-in With single Z-Board With double Z-Board With single Z-Board and ribbon cable With double Z-Board and ribbon cable * Manifold assemblies with adapter to ISO 507-, see following page. 035 Series Manifold assemblies with side ports with bottom ports B G / G 3/8 NPTF / NPTF 3/8 G 3/8 G 3/8 NPTF 3/8 NPTF 3/8 Weight approx. With single Z-Board With double Z-Board With single Z-Board and ribbon cable With double Z-Board and ribbon cable GB-008/R0 X0-7-3

10 Manifold Assembly Kits to ISO / 0 / 035 Series Spare Parts Manifold Assembly Kits to ISO Manifold Assembly Kits - Size 8 mm ISO 507- Side ports /8 NPTF G /8 / Push-in 6mm Push-in 5/6 (8mm) Push-in Bottom ports /8 NPTF G /8 / NPTF G /8 G /8 Single Z-Board Double Z-Board Single Z-Board w/ ribbon cable Double Z-Board w/ ribbon cable Passive GB-03/R0 Manifold Assembly Kits - Size 6 mm ISO 507- Side ports / NPTF 3/8 NPTF G / G 3/8 / Push-in Bottom ports / NPTF / NPTF G / G / / NPTF Single Z-Board Double Z-Board Single Z-Board w/ ribbon cable Double Z-Board w/ ribbon cable Passive Manifold Assembly Kits - Size 6 mm ISO 507- Side ports 3/8 Push-in 8 mm Push-in 0 mm Push-in Bottom ports / NPTF G / G / Single Z-Board Double Z-Board Single Z-Board w/ ribbon cable Double Z-Board w/ ribbon cable Passive Ribbon cable for Valve Station with 7th Solenoid Description Ribbon cable X0-7-35

11 005 / 0 / 035 Series Spare Parts Mid-Station Supply & Exhaust Block Mid-Station Supply & Exhaust Block Add additional supply and exhaust capacity to large manifold assemblies Add different pressure to manifold section with use of blocking disks Same size as standard manifold block with blank station plate 005 Series Description Weight Order approx. Mid-station supply & exhaust block with threaded side ports in G /8* Mid-station supply & exhaust block with side push-in fittings * On request: Threaded ports in NPTF /8 0 Series Description Weight Order approx. Mid-station supply & exhaust block with threaded side ports in G 3/ Mid-station supply & exhaust block with threaded side ports in NPTF 3/ Mid-station supply & exhaust block with side push-in fittings 0 mm Series Description Weight Order approx. Mid-station supply & exhaust block On request: Threaded ports in NPTF Manifold Assemblies with Aux. VDC Power Connection 005 Series Description Weight Order approx. Manifold assembly with single Z-Board, side ports with 8 mm push-in fittings Manifold assembly with double Z-Board, side ports with 8 mm push-in fittings Series Description Weight Order approx. Manifold assembly with single Z-Board, side ports with 0 mm push-in fittings Manifold assembly with double Z-Board, side ports with 0 mm push-in fittings GB-008/R0² X0-7-36

12 Conversion of Pilot Air Supply 005 / 0 / 035 Series Spare Parts Conversion of Pilot Air Supply Manifolds can easily be converted from internal to external pilot supply. When converting from internal to external pilot supply, please ensure that the manifold is not pressurised, as pressure is applied to the end plate covers. 005 Series For external pilot supply plug here. Left end plate only! For internal pilot supply plug here. Left end plate only! 0 Series For external pilot supply plug here. For internal pilot supply plug here. In both end plates! For internal pilot supply plug here. In both end plates! 0096GB-008/R0 035 Series For internal pilot supply plug here. Left end plate only! Plug for conversion of pilot supply For external pilot supply plug here. Left end plate only! X0-7-37

13 0 Series Spare Parts Adaptor Plate Kits Adaptor Plate Kits The kit includes the adapter plate, transfer board, gasket, screws and studs. Individual end plates for the 005 and 0 are not incuded. This adaptor allows the transition from the 0 to the 005 series. EXAMPLE ORDERS: Adapter plate kit: Valves: and mounting: AKJGBEB003LMUF BBZML0006 BAZML BAZML BAZML0006 ASSEMBLED Adaptor Plate Kit with Standard End Plates ( STD Option) Description 005 with 3/8 G-tap to 0 with 3/8 and / G-tap 005 with 0 mm push-in to 0 with 0 and mm push-in Adaptor Plate Kit with Standard End Plates and Muffler ( MUF Option) Description 005 with 3/8 G-tap to 0 with 3/8 and / G-tap 005 with 0 mm push-in to 0 with 0 and mm push-in Adaptor Plate Kit with Standard End Plates and DIN rail mount ( DRM Option) Description 005 with 3/8 G-tap to 0 with 3/8 and / G-tap 005 with 0 mm push-in to 0 with 0 and mm push-in Transition Plate Kit only Dimensions [mm] C Adaptor Plate Kit with Standard End Plates, muffler and DIN rail mount ( DWM Option) Description 005 with 3/8 G-tap to 0 with 3/8 and / G-tap 005 with 0 mm push-in to 0 with 0 and mm push-in Description A B C Weight Order A B approx Transition plate for 0 left of Transition plate for 0 ISO 507-6mm left of 005 ISO 007-8mm Transition plate for 0 ISO 507-6mm left of ISO 5599/ size C 0096GB-009/R0 X0-7-38

14 035 Series Spare Parts Transition Plate Kits Transition Plate Kits Adapter plate kit The kit includes the adapter plate, transfer board, gasket, screws and studs. Individual end plates for the 005 and 0 are not incuded. This adaptor allows the transition from the 035 to the 0 series. EXAMPLE ORDERS* : Adapter plate kit: Valves: and mounting: AKJBBGB00XGMUF 35BAZMG BBZMG0006 BAZMG0006 BBZMG0006 ASSEMBLED *0 Series = G 0096GB-008/R0 Adapter Plate Kit with Standard End Plates ( STD Option) Description 035 with / G-tap to 0 with 3/8 and / G-tap 035 with / NPTF-tap to 0 with 3/8 and / NPTF-tap Transition Plate Kit only A Adapter Plate Kit with Standard End Plates and Muffler ( MUF Option) Description 035 with / G-tap to 0 with 3/8 and / G-tap 035 with / NPTF-tap to 0 with 3/8 and / NPTF-tap Dimensions [mm] Description A Order Transition plate for 035 left of X0-7-39

15 D D F H J H End Plate with 5 Pin SUB-D Connector ( J ) Fieldbus Electronics and I/O G- Electronics Spare Parts End Plate with Sub-D Connector Pin 5 Earth ground 5 PIN SUB-D CONNECTOR G Pins 3- Pins - OUTPUTS Pins 3- A B C Pins - Drive of coils Pin E Clearance hole for M6 screw Note: External fusing or output protection recommended. Dimensions [mm] Description A B C D E F G H J Weight approx. Order End plate, 5 pin standard mount End Plate with 37 Pin SUB-D Connector ( M ) Pin 37 Pins PIN SUB-D CONNECTOR Pins -3 OUTPUTS G A B C Pins -3 Drive of coils Pins Pin Dimensions [mm] Description A B C D E F G H J Weight approx. Order End plate, 37 pin standard mount E Clearance hole for M6 screw F Note: External fusing or output protection recommended. 0096GB-008/R0 X0-7-0

16 H G D F Fieldbus Electronics and I/O G- Electronics Spare Parts End Plate with Terminal Strips End Plate with Terminal Strip for -6 ( AKF ) or -3 ( AKT ) Outputs Description Weight Order End plate with terminal strip (-6) standard mount End plate with terminal strip (-3) standard mount L 3/ NPTF J K TERMINAL STRIP Terminal -6 DRIVE OF COILS TERMINAL STRIP Terminal -3 DRIVE OF COILS Terminal -6 OUTPUTS Terminal com Terminal -3 OUTPUTS Terminal com B C A Terminal com 8 AWG WIRE MAXIMUM Conductor cross-section max mm Terminal com 8 AWG WIRE MAXIMUM Conductor cross-section max mm E Dimensions [mm] 0096GB-008/R0 Clearance hole for M6 screw Note: External fusing or output protection recommended. A B C D E F G H J K L X0-7-

17 Fieldbus Electronics and I/O G- Electronics Spare Parts End Plates with Round Connectors End Plate with pin ( P ), 9 pin ( Q ), 6 pin ( R ) or +6 pin ( S ) Round Connector Description Weight Order approx. End plate with pin round connector standard mount End plate with 9 pin round connector standard mount End plate with 6 pin round connector standard mount End plate with 6+ pin round connector standard mount PIN ROUND CONNECTOR Pins -8 INPUTS Pins 9-0 Pin not used Pin 39-5 D 9 PIN ROUND CONNECTOR Pin = solenoid 5 Pin = solenoid Pin 3 = solenoid 7 Pin = solenoid Pin 5 = solenoid 3 Pin 6 = Pin 7 = solenoid Pin 8 = solenoid 6 Pin 9 = solenoid 0 Pin 0 = solenoid Pin = solenoid 3 Pin = Pin 3 = solenoid Pin = solenoid 8 Pin 5 = solenoid Pin 6 = solenoid 5 Pin 7 = solenoid 9 Pin 8 = solenoid 6 Pin 9 = not used 6 PIN ROUND CONNECTOR Pins - OUTPUTS - Pins -5 Pin PIN ROUND CONNECTOR Pins -0 OUTPUTS 3-3 Pin Pin Pins -5 Pin 6 Pins - DRIVE OF COILS Pins -0 DRIVE OF COILS Pin Pin E C A B Clearance hole for M6 screw Dimensions [mm] G F A B C D E F G H J3, H J Note: External fusing or output protection recommended. 0096GB-008/R0 X0-7-

18 Fieldbus Electronics and I/O G- Electronics Spare Parts Communication Module Kits Communication Module Kit Description Weight approx. Complete unit Allen-Bradley RIO (incl. Pos. to 7) with 7/8 connector, standard (one housing) Complete unit Allen-Bradley RIO (incl. Pos. to 7) with M connector (one housing) Complete unit Interbus -S M3 connector (one housing) Complete unit ControlNet (two housings) Complete unit FIPIO Interface (two housings) Complete unit Fieldbus Foundation (H FF) (one housing) Manual Configuration Module (MCM) Description Weight Order approx. Complete MCM (incl. Pos. to 0) GB-0/R0 G- Electronics Spare Parts AS-Interface Module Kits Valve Capability Input Capability Version Addressing Connector Order code 8 8 V. Standard Vampire V. Standard Vampire 0-5 AS-Interface 6 8 V. Extended Vampire 0- module 6 V. Extended Vampire V3.0 Entended Vampire V3.0 Entended Vampire 0-30 Input module *M 0- X0-7-3

19 Fieldbus Electronics and I/O G- Electronics Spare Parts M I/O Modules 8 M Wide Module with short-circuit protection Description Weight 6 Inputs 6 Outputs approx. PNP NPN PNP Complete unit sourcing PNP (incl. Pos. to 0) i 0-3 i i i i With short-circuit protection i i With short-circuit protection and status bit I/O Pin Assignment Single Sourcing Double Sourcing INPUT MODULE OUTPUT MODULE INPUT MODULE OUTPUT MODULE female Pin = + VDC Pin 3 = (-) GND Pin = input (sourcing) female Pin = not used Pin 3 = (-) GND Pin = output (sourcing) 0.5 A max. female Pin = + VDC Pin = input (sourcing) Pin 3 = (-) GND Pin = input (sourcing) female Pin = not used Pin = output (sourcing) Pin 3 = (-) GND (Common) Pin = output (sourcing) 0.5 A max. G- Electronics I/O Module Wiring Accessories Accessory Description 5 pin straight male M connector pin elbow male M connector M plug pin male DUO M connector for inputs ( cables, Ø3-5 mm) GB-0/R0 X0-7-

20 Left Mounting Cover Assembly Fieldbus Electronics and I/O G- Electronics Spare Parts Cover Assemblies - Fuses Description LH cover, DIN rail only on request LH standard cover on request Right Mounting Cover Assembly Description RH cover, DIN rail only on request RH standard cover on request GB-008/R0 Plug-in Blade Terminal Fuse Dimensions [mm] Description Rating (A) Littlefuse- Type A B C D E F Blade terminal fuse, colour: pink ,, , Blade terminal fuse, colour: red ,, , Fuse X0-7-5

21 Communication module Fieldbus Electronics and I/O G3 Electronics Spare Parts M I/O Modules Description Weight (g) DeviceNet EtherNet/IP Modbus TCP/IP Profibus DP Profibus DP automobive version Profinet Powerlink Canopen DeviceLogix Module d Input / Output E/S M Description Signal type PNP NPN 8 Inputs Inputs 8 Inputs + earth Inputs Inputs + earth Outputs PNP Outputs 6 Outputs PNP Outputs PNP high current (A) Input and Output 8 Inputs & 8 Outputs 0- - Analog I/O 5-pin M Description analog I/O Analog I/O for proportional valves (Sentronic PLUS ) Signal type 0-0 VCC -0 ma Inputs 0-0- Inputs & Outputs Inputs &t Outputs Terminal strip module Description Signal type PNP NPN Inputs 6 Inputs GB-008/R0 X0-7-6