Parts Catalog Issued: Feb 5, Invacare I-Lift. Patient Transport Lift

Transcription

1 Parts Catalog Issued: Feb 5, 2016 Invacare I-Lift Patient Transport Lift

2 Parts Catalog Usage Guide The information contained in this document is subject to change without notice. This catalog contains service parts for. If you have any questions regarding this catalog, please contact one of our Customer Service Representatives. SYMBOL DEFINITION For Customer Service Support Call: For Faxed In Orders Call: or For Technical Service Call: Literature Can Be Found at: or Throughout this catalog you will notice letters to draw your attention to specific footnotes which are located at the bottom of the page or below specified charts. Examples: A,B,C etc. NOTE: NLA = Special Comments = General information pertaining to that specific page = No Longer Available HARDWARE MEASUREMENTS The measurements for the hardware will be listed as follows: Screws, Bolts Diameter X Thread Count/Pitch X Length Washers Inside Diameter X Outside Diameter X Thickness Spacers Inside Diameter X Outside Diameter X Length For your convenience, we have supplied an area for you to list your Invacare Representatives. Name Phone Numbers 2016 Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by and. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted. 1

3 TABLE of CONTENTS Description Page Number 00. Product Pictures ILIFTEE - Electric Lift - Mast / Boom Assembly ILIFTEE - Electric Lift - Hanger Bar, Labels, Battery Pack and Controller ILIFTEE - Electric Lift - Base ILIFTHM - Hydraulic Lift - Mast / Boom Assembly ILIFTHM - Hydraulic Lift - Hanger Bar and Labels ILIFTHM - Hydraulic Lift - Base ILIFTEM - Manual Lift - Mast / Boom Assembly ILIFTEM - Manual Lift - Hanger Bar, Labels, Battery Pack and Controller ILIFTEM - Manual Lift - Base

4 Product Pictures 3

5 Electric Lift - Mast / Boom Assembly NOTE: Items that are not shown in this category but are included in Kits in the Parts List are used on other I-Lift Applications. All fasteners must be torqued to IFI/DIN standards. 4

6 Electric Lift - Mast / Boom Assembly NOTE: Items that are not shown in this category but are included in Kits in the Parts List are used on other I-Lift Applications. All fasteners must be torqued to IFI/DIN standards. Item Number Note Part Number Description A B C D E F Quantity Per Package Assembly 163 Boom Assembly Mast Assembly, Electric Push Handle Actuator Motor NLA - Kit, Boom Mounting Hardware 1 1 Cap, End 1 4 Screw, Hex Head (M10 x 1.5 x 58mm) 1 1 Screw, Shoulder Hex Socket Head (3/8 x 1-1/2", 1 1 5/16-18) Washer (10.5 x 20 x 2mm) 1 4 Bushing (10 x 18 x 49mm) 1 1 Bearing, Teflon 1 2 Screw, Hex Head (M10 x 1.5 x 80mm) 1 1 Washer, Nylon (20 x 10.2 x 4.2mm) 1 2 Locknut (5/16-18) 1 1 Bushing (10 x 12 x 28mm) Kit, Push Handle Mounting Hardware 1 1 Cap, End 1 4 Washer (10.5 x 20 x 2mm) 1 4 Screw, Hex Head (M10 x 1.5 x 75mm) NLA - Kit, Actuator Hardware, Mast 1 1 Protector, Mast 1 1 Screw, Socket Head Cap (M5 x.8 x 10mm) 1 2 Clip, Hydraulic 1 1 Clip, Actuator 1 1 Rivet (4 x mm) 1 2 Screw, Socket Button Head (M5 x.8 x 12mm) Kit, Actuator Mounting Hardware 1 1 Cap, End 1 2 Screw, Hex Head (M10 x 1.5 x 58mm) 1 1 Washer (10.5 x 20 x 2mm) 1 2 Locknut (M10 x 1.5mm) 1 1 Bushing (10 x 12 x 28mm) 1 1 Lock, Wire Kit, Folding Hook 1 1 Hook, Folder 1 1 Pin, Locking shaft (10 x 50mm) 1 1 Pin (8 x 36mm) 1 1 Spring, Hook Kit, Mast Connector Hardware 1 1 5

7 Electric Lift - Mast / Boom Assembly NOTE: Items that are not shown in this category but are included in Kits in the Parts List are used on other I-Lift Applications. All fasteners must be torqued to IFI/DIN standards. Item Number Note Part Number Description NOTE: Quantity Per Package Assembly Washer (10.5 x 20 x 2mm) 1 4 Bearing (16 x 10 x 25mm) 1 2 Screw, Hex Head (M10 x 1.5 x 75mm) 1 2 Washer (5.2 x 10 x 1mm) 1 1 Pin, Lock Plate (M5 x 80mm) 1 1 Spring (.5 x 5 x 50mm) 1 1 Plate, Lock 1 1 Ball (20mm) w/ Stud, Threaded (M6 x 1 x 13mm) 1 1 Rubber, Anti Scratch 1 1 Screw (M4 x 7mm) 1 1 A - Includes items 11-20, and 25. Items 13, 19, and 20 are not used on this Model and are not shown. B - Includes items 11, -, and 29. C - Includes items 21-24, 26, and 41. Item 41 is not used on this Model and is not shown. D - Includes items 11-12,,, 25, and 27. E - Includes items F - Includes items,, 28, 29, and NOTE: Some Items that are not shown on Illustration but are included in Kits on this page are used for other I-Lift Applications. All fasteners must be torqued to IFI/DIN standards. 6

8 Electric Lift - Hanger Bar, Labels, Battery Pack and Controller NOTE: Item #22 Battery and Bracket Kit is currently not available at this time. Use Items 23, 24, and 25 to replace battery. 7

9 Electric Lift - Hanger Bar, Labels, Battery Pack and Controller NOTE: Item #22 Battery and Bracket Kit is currently not available at this time. Use Items 23, 24, and 25 to replace battery. 8

10 Electric Lift - Hanger Bar, Labels, Battery Pack and Controller NOTE: Item #22 Battery and Bracket Kit is currently not available at this time. Use Items 23, 24, and 25 to replace battery. Item Number Note Part Number Description Quantity Per Package Assembly 1 A Kit, Hanger Bar Mounting Hardware Plug, Boom Foam, Cover Pin, Clevis (M10) Clip (M10) B Kit, Hanger Bar Retainer Strap and Plug Button Pin, Roll Strap Retainer Plug, Hanger Bar C Kit, Hanger Bar Pin Assembly Clip, "C" 1 1 O-Ring 1 2 Washer, Bearing Pin, Hanger Bar D Kit, Label Label, Weight US Label, I-Lift Decal, Invacare Logo (3.1) Label, Sling Label, Warning, Lift, 450 Pound Capacity E NLA NLA - Kit, Battery and Mounting Bracket Bracket, Battery - Electric Only Screw, Phillips, Pan Head (10-24 x 1/4") Battery Bracket, Battery - Electric Only Screw, Phillips Pan Head (#10-24 x 1/4") Battery Pack Hanger Bar Assembly Controller Pendant, Four Channel w/ Hook Bracket, Wall Mount Charger - Electric Only Charger Cord, USA - Electric Only 1 1 NOTE: A - Includes items 5, 6, 7, and 8. B - Includes items 10, 11, and 12. C - Includes items 13,,, and 16. D - Includes items 17, 18, 19, 20, and 21. E is not currently available at this time, please use the following part numbers as replacements, item 23 ( ), item 24 ( ), and item 25 (12383). 9

11 Electric Lift - Base 10

12 Electric Lift - Base Item Number Note Part Number Description Quantity Per Package Assembly Leg Assembly Cover, Leg Protection Shroud, Electric Base Clip, Shroud Actuator A Kit, Rear Caster w/ Hardware, Locking (Pair) Screw, Socket, Countersunk Head (M10 x 1.5 x mm) 11 Spacer (41.3 x 10.2 x mm) Caster, Rear Locking B Kit, Front Caster w /Hardware (Pair) Screw, Socket, Countersunk Head (M10 x 1.5 x mm) Spacer (40 x 10.5 x 3mm) 1 2 Caster, Front C Kit, Leg to Crossmember Mounting Hardware (Pair) Bushing, Bronze Bushing, Base and Leg Screw, Socket Button Head, (M10 x 1.5 x 22mm) Lock Washer, Split (M10) D Kit, Actuator Mounting Hardware Washer (10.5 x 20 x 2mm) Plate, Support, Electric Base Washer (28mm x 12mm x 2mm) Pin, Hitch (3/8 x 1-3/16") Bearing, Flange (12mm x 18mm x 7.6mm) Screw, Socket Head (M12 x 1.75 x 30mm) NLA - Pin, Clevis (10mm x 44mm) Bracket, Linkage E Kit, Linkage (Pair) Screw, Socket Button Head w/ Patch (M8 x 1.25 x mm) 29 Tie Rod Assembly 1 2 NOTE: A - Includes items and 21. B - Includes items 13- and 21. C - Includes items D - Includes items E - Includes items

13 Hydraulic Lift - Mast / Boom Assembly NOTE: Items that are not shown in this category but are included in Kits in the Parts List are used on other I-Lift Applications. All fasteners must be torqued to IFI/DIN standards. 12

14 Hydraulic Lift - Mast / Boom Assembly NOTE: Items that are not shown in this category but are included in Kits in the Parts List are used on other I-Lift Applications. All fasteners must be torqued to IFI/DIN standards. Item Number Note Part Number Description A,C,D, E F B G Quantity Per Package Assembly 163 Boom Assembly NLA NLA - Mast Assembly, Hydraulic Push Handle NLA NLA - Pump, Hydraulic NLA - Kit, Boom Mounting Hardware 1 1 Cap, End 1 4 Screw, Hex Head (M10 x 1.5 x 58mm) 1 1 Screw, Shoulder Hex Socket Head (3/8 x 1-1/2", 1 1 5/16-18) Washer (10.5 x 20 x 2mm) 1 4 Bushing (10 x 18 x 49mm) 1 1 Bearing, Teflon 1 2 Screw, Hex Head (M10 x 1.5 x 80mm) 1 1 Washer, Nylon (20 x 10.2 x 4.2mm) 1 2 Locknut (5/16-18) 1 1 Bushing (10 x 12 x 28mm) Kit, Push Handle Mounting Hardware 1 1 Cap, End 1 4 Washer (10.5 x 20 x 2mm) 1 4 Screw, Hex Head (M10 x 1.5 x 75mm) NLA - Kit, Actuator Hardware, Mast 1 1 Protector, Mast 1 1 Screw, Socket Head Cap (M5 x.8 x 10mm) 1 2 Clip, Hydraulic 1 1 Clip, Actuator 1 1 Rivet (4 x mm) 1 2 Screw, Socket Button Head (M5 x.8 x 12mm) Kit, Mast Connector Hardware 1 1 Washer (10.5 x 20 x 2mm) 1 4 Bearing (16 x 10 x 25mm) 1 2 Screw, Hex Head (M10 x 1.5 x 75mm) 1 2 Washer (5.2 x 10 x 1mm) 1 1 Pin, Lock Plate (M5 x 80mm) 1 1 Spring (.5 x 5 x 50mm) 1 1 Plate, Lock 1 1 Ball (20mm) w/ Stud, Threaded (M6 x 1 x 13mm) 1 1 Rubber, Anti Scratch 1 1 Screw (M4 x 7mm)

15 Hydraulic Lift - Mast / Boom Assembly NOTE: Items that are not shown in this category but are included in Kits in the Parts List are used on other I-Lift Applications. All fasteners must be torqued to IFI/DIN standards. Item Number Note Part Number Description Quantity Per Package Assembly 9 H Kit, Folding Hook Hook, Folder Pin, Locking shaft (10 x 50mm) Pin (8 x 36mm) Spring, Hook 1 1 NOTE: A - Includes items and 23. Items 12 and 23 are not used on this Application and are not shown in the illustration. B - Includes items and Item 25 is not used on this Application and is not shown in the illustration. C - Hydraulic Lift requires only (2) of Item 10. D - Hydraulic Lift requires only (2) of Item. E - Hydraulic Lift requires only (2) of Item 17. F - Includes items 10, 13,, and 28. G - Includes items 13,, 27, 28, and H - Includes items NOTE: Items that are not shown in this category but are included in Kits in the Parts List are used on other I-Lift Applications.

16 Hydraulic Lift - Hanger Bar and Labels

17 Hydraulic Lift - Hanger Bar and Labels Item Number Note Part Number Description Quantity Per Package Assembly 1 A Kit, Hanger Bar Mounting Hardware Plug, Boom Foam, Cover Pin, Clevis (M10) Clip (M10) B Hanger Bar Assembly C Kit, Hanger Bar Retainer Strap and Plug Button Pin, Roll Strap Retainer Plug, Hanger Bar D Kit, Hanger Bar Pin Assembly Clip, "C" 1 1 O-Ring 1 2 Washer, Bearing Pin, Hanger Bar E Kit, Label Label, Weight US Label, I-Lift Decal, Invacare Logo (3.1) Label, Sling Label, Warning, Lift, 450 Pound Capacity 1 1 NOTE: A - Includes items 5, 6, 7, and 8. B - Includes the Hanger Bar and items 10, 11, and 12. C - Includes items 11, 12, and 13. D - Includes items 13,,, and 16. E - Includes items

18 Hydraulic Lift - Base 17

19 Hydraulic Lift - Base Item Number Note Part Number Description A B C D E F G Quantity Per Package Assembly Leg Assembly Cover, Leg Protection Shroud, Manual Base Clip, Shroud Kit, Rear Caster w/ Hardware, Locking (Pair) 1 1 Screw, Socket, Countersunk Head (M10 x 1.5 x mm) Spacer (41.3 x 10.2 x mm) 1 2 Caster, Rear Locking Kit, Front Caster w /Hardware (Pair) 1 1 Screw, Socket, Countersunk Head (M10 x 1.5 x mm) Spacer (40 x 10.5 x 3mm) 1 2 Caster, Front Kit, Leg to Crossmember Mounting Hardware (Pair) 1 1 Bushing, Bronze 1 4 Bushing, Base and Leg 1 2 Screw, Socket Button Head, (M10 x 1.5 x 22mm) 1 2 Lock Washer, Split (M10) Kit, Index Plate w /Hardware 1 1 Washer (10.5 x 20 x 2mm) 1 2 Index Plate Assembly Kit, Handle Mount 1 1 Handle, Mount 1 1 Spring, Compression (1 x 1-1/16 x 1/8") 1 1 Screw, Shoulder Hex Socket Head w/ Patch (1/2" x /4", 3/8-16) Kit, Linkage (Pair) 1 1 Screw, Socket Button Head w/ Patch (M8 x 1.25 x mm) Tie Rod Assembly Kit, Handle w /Grip 1 1 Handle 1 1 Grip, Cane

20 Hydraulic Lift - Base NOTE: A - Includes items 12- and 23. B - Includes items -17 and 23. C - Includes items D - Includes items E - Includes items F - Includes items G - Includes items

21 Manual Lift - Mast / Boom Assembly 20

22 Manual Lift - Mast / Boom Assembly Item Number Note Part Number Description A B C D E Quantity Per Package Assembly 163 Boom Assembly Mast Assembly, Manual Push Handle Actuator Motor NLA - Kit, Boom Mounting Hardware 1 1 Cap, End 1 4 Screw, Hex Head (M10 x 1.5 x 58mm) 1 1 Screw, Shoulder Hex Socket Head (3/8 x 1-1/2", 1 1 5/16-18) Washer (10.5 x 20 x 2mm) 1 4 Bushing (10 x 18 x 49mm) 1 1 Bearing, Teflon 1 2 Screw, Hex Head (M10 x 1.5 x 80mm) 1 1 Washer, Nylon (20 x 10.2 x 4.2mm) 1 2 Locknut (5/16-18) 1 1 Bushing (10 x 12 x 28mm) Kit, Push Handle Mounting Hardware 1 1 Cap, End 1 4 Washer (10.5 x 20 x 2mm) 1 4 Screw, Hex Head (M10 x 1.5 x 75mm) NLA - Kit, Actuator Hardware, Mast 1 1 Protector, Mast 1 1 Screw, Socket Head Cap (M5 x.8 x 10mm) 1 2 Clip, Hydraulic 1 1 Clip, Actuator 1 1 Rivet (4 x mm) 1 2 Screw, Socket Button Head (M5 x.8 x 12mm) Kit, Actuator Mounting Hardware 1 1 Cap, End 1 2 Screw, Hex Head (M10 x 1.5 x 58mm) 1 1 Washer (10.5 x 20 x 2mm) 1 2 Locknut (M10 x 1.5mm) 1 1 Bushing (10 x 12 x 28mm) 1 1 Lock, Wire Kit, Folding Hook 1 1 Hook, Folder 1 1 Pin, Locking shaft (10 x 50mm) 1 1 Pin (8 x 36mm) 1 1 Spring, Hook

23 Manual Lift - Mast / Boom Assembly Item Number Note Part Number Description Quantity Per Package Assembly 10 F Kit, Mast Connector Hardware 1 1 Washer (10.5 x 20 x 2mm) Bearing (16 x 10 x 25mm) Screw, Hex Head (M10 x 1.5 x 75mm) Washer (5.2 x 10 x 1mm) Pin, Lock Plate (M5 x 80mm) Spring (.5 x 5 x 50mm) Plate, Lock Ball (20mm) w/ Stud, Threaded (M6 x 1 x 13mm) Rubber, Anti Scratch Screw (M4 x 7mm) 1 1 NOTE: A - Includes items and 25. Items 13, 19 and 20 are not used on this Model and are not shown. B - Includes items 11- and 29.. C - Includes items 21-24, 26 and 41. Item 41 is not used on this Model and is not shown. D - Includes items 11-12, -, 25 and 27. Item 27 is not used on this Model and is not shown. E - Includes items F - Includes items -, and Note: Items that are not shown on Illustration but are included in Kits on this page are used for other Model Applications. 22

24 Manual Lift - Hanger Bar, Labels, Battery Pack and Controller NOTE: Item #22 Battery and Bracket Kit is currently not available at this time. Use Items 23, 24, and 25 to replace battery. 23

25 Manual Lift - Hanger Bar, Labels, Battery Pack and Controller NOTE: Item #22 Battery and Bracket Kit is currently not available at this time. Use Items 23, 24, and 25 to replace battery. 24

26 Manual Lift - Hanger Bar, Labels, Battery Pack and Controller NOTE: Item #22 Battery and Bracket Kit is currently not available at this time. Use Items 23, 24, and 25 to replace battery. Item Number Note Part Number Description 1 A B C D E 22 F,G Quantity Per Package Assembly Kit, Hanger Bar Mounting Hardware 1 1 Plug, Boom 1 1 Foam, Cover 1 1 Pin, Clevis (M10) 1 1 Clip (M10) Kit, Hanger Bar Retainer Strap and Plug Button 1 1 Pin, Roll 1 6 Strap Retainer 1 6 Plug, Hanger Bar Kit, Hanger Bar Pin Assembly 1 1 Clip, "C" 1 1 O-Ring 1 2 Washer, Bearing 1 1 Pin, Hanger Bar Kit, Label 1 1 Label, Weight US 1 1 Label, I-Lift 1 2 Decal, Invacare Logo (3.1) 1 2 Label, Sling 1 2 Label, Warning, Lift, 450 Pound Capacity Hanger Bar Assembly NLA NLA - Kit, Battery and Mounting Bracket 1 1 Bracket, Battery - Electric Only 1 1 Screw, Phillips, Pan Head (10-24 x 1/4") 1 3 Battery Bracket, Battery - Electric Only Screw, Phillips Pan Head (#10-24 x 1/4") Battery Pack Controller Pendant, Two Channel w/ Hook Bracket, Wall Mount Charger - Electric Only Charger Cord, USA - Electric Only

27 Manual Lift - Hanger Bar, Labels, Battery Pack and Controller NOTE: Item #22 Battery and Bracket Kit is currently not available at this time. Use Items 23, 24, and 25 to replace battery. NOTE: A - Includes items 5, 6, 7, and 8. B - Includes items 10, 11, and 12. C - Includes items 13,,, and 16. D - Includes items E - Includes Hanger Bar and items 11, 12, and 13. F - Includes items 23, 24, and 25. G is not currently available at this time, please use the following part numbers as replacements, item 23 ( ), item 24 ( ), and item 25 (12383). 26

28 Manual Lift - Base 27

29 Manual Lift - Base Item Number Note Part Number Description A B C D E F G Quantity Per Package Assembly Leg Assembly Cover, Leg Protection Shroud, Manual Base Clip, Shroud Kit, Rear Caster w/ Hardware, Locking (Pair) 1 1 Screw, Socket, Countersunk Head (M10 x 1.5 x mm) Spacer (41.3 x 10.2 x mm) 1 2 Caster, Rear Locking Kit, Front Caster w /Hardware (Pair) 1 1 Screw, Socket, Countersunk Head (M10 x 1.5 x mm) Spacer (40 x 10.5 x 3mm) 1 2 Caster, Front Kit, Leg to Crossmember Mounting Hardware (Pair) 1 1 Bushing, Bronze 1 4 Bushing, Base and Leg 1 2 Screw, Socket Button Head, (M10 x 1.5 x 22mm) 1 2 Lock Washer, Split (M10) Kit, Index Plate w /Hardware 1 1 Washer (10.5 x 20 x 2mm) 1 2 Index Plate Assembly Kit, Handle Mount 1 1 Handle, Mount 1 1 Spring, Compression (1 x 1-1/16 x 1/8") 1 1 Screw, Shoulder Hex Socket Head w/ Patch (1/2" x /4", 3/8-16) Kit, Linkage (Pair) 1 1 Screw, Socket Button Head w/ Patch (M8 x 1.25 x mm) Tie Rod Assembly Kit, Handle w /Grip 1 1 Handle 1 1 Grip, Cane

30 Manual Lift - Base NOTE: A - Includes items 12- and 23. B - Includes items -17 and 23. C - Includes items D - Includes items E - Includes items F - Includes items G - Includes items

31 Invacare Corporation One Invacare Way Elyria, Oh USA Technical Support Customer Service Literature Orders Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by and. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted. (Revised 02/05/16)