T-630 CAT Engine Wiring

Transcription

1 T-630 CAT Engine Wiring Start sequence: Key to Run position: The Amperite Relay in the Black Box timer sequence is started to test all diagnostic lights for 5 seconds. The fuel lift pump and injector pump are also energized. If the engine is not started within 5 seconds, all lights go out but the low oil pressure light. It should go out when the engine is started and oil pressure rises. Key to Start position: Electric flow to start passes through the key switch to Terminal E on the lower terminal in the black box. From E through the Neutral Start switch on the Main Pump to Terminal 1 on the upper strip. Then through one of the N/C contacts on the E-Stop to the Start Relay in the Black Box. This relay should then energize the starter. E-Stop pressed: All diagnostic lights come on and stay on. The fuel pump circuit is opened, and the circuit to activate the starter is opened. (It will not even try to turn the starter)

2 T-630 CAT Engine Trouble Shooting Key Switched on, All 4 indicator lights stay on, but engine will not try to start. Engine will not even turn over. E-Stop is pushed in on Black Box on drivers side of engine. Key Switched on, No lights light, nothing works at all Check and Re-Set Circuit Breaker in Black Box on drivers side of engine. Double check battery voltage Replace Fuse Engine suddenly starts running rough and puffing smoke. Check Lift Pump Fuse in Black Box If you do not have an Air Dryer on the machine, the Air Dryer Relay is a spare relay. Move the Air Dryer Relay to the Fuel Lift Pump Position. Check Fuel Lift Relay in Black Box. Make sure 12v on Terminal 7 (Upper strip) with Key On. Double check 12v at Lift Pump. Possible clean and/or replace Lift Pump

3 T-630 CAT Engine Trouble Shooting Key on, Diagnostic lights come on and all but low oil go out after 5 seconds, but engine does not even try to start (starter does not engage at all). Probably Neutral Start safety on main pump. With key off, confirm continuity between terminal E on lower strip and 1 on upper strip in Black Box. Is there Continuity? Remove bolt connecting Air Cylinder eye to actuator arm on main pump. Check continuity again. Is it OK now? Refer to Black Box wiring schematic. Blue wire from Terminal 1 goes to E-Stop, 1 of the Normally Closed contact blocks. Is there continuity through the contacts with the E-Stop out? Move pump lever by hand back and forth slightly to see if continuity can be established. Adjust eye on cylinder rod ½ turn at a time to correct alignment. Replace N/C Contact Check Start relay in Black Box for proper operation. Is it OK? Refer to wiring diagram and confirm wiring not broken. Replace Relay Refer to wiring diagram and confirm wiring not broken. Wiring OK Contact your local CAT Dealer. Wiring OK Refer to Neutral Start adjustment procedure in pump manual. Possible Switch replacement necessary.

4 Level, Alternator Excite, etc Black #18 1 E-Stop Black #18 Blue #18 Green # Glow Plug Air Dryer Red #10 Red #14 Red #14 Black #18 Grounds #18 Black Fuel Lift 2 Start Red #12 Light Test 5 Seconds. Amperite Relay Red #18 Inline 10 Amp Black #8 Ground 4 10 Amp 30 Amp Orange #14 Red #12 Red #14 Black #14 Black #14 White #12 BU Yellow #18 Level Signal 8 Black #18 Blue #18 Gray #14 Red #18 Temp Red #10 Gray #18 Level +12v Red #8 Red # Gray #14 Orange #14 Optional Air Dryer 5 60 Amp Breaker Red #14 Alternator Excite 6 Starter A B C D E F G H I J Black #18 Red #8 +12V on Starter Red #12 Start Signal Hydraulic Level Indicator Lights in Cab Green #18 Low Hydraulic Signal Cat Main Harness Green - Low Hydraulic Brown Oil Pressure Red Temp Yellow Low Blue #12 Drive Lights Blue #18 Neutral Start Gray #14 Fuel Pump Red #14 Fuel Thermostat Red #14 Fuel Lift Brown #18 Oil Pressure Yellow #12 High/Low Blue #18 Neutral Start Red #10 Glow Plug 9 Cab Main White #8 Power to Cab Red #10 Ignition On Green # 12 Glow Plug Black #12 Start Yellow # 12 High/Low Blue #10 Drive Lights Brown #12 Not Used

5 Cat Engine Wiring BOM E-Stop Grainger Tucker # Quantity Push-Pull 6HW NC/NO Contact Block w/base 6HX NO-NC 1 NO Contact 6HZ NO NC Contact 6HZ NC 1 Name Plate 6JC Tyco Relay's Tyco Relay VF7-41F Relay Socket VCF Terminal Terminal Amperite Time Delay Relay 12DSPDT5SC Waytek Fuse Panel Terminal Strip Terminal Strip

6 Wiper (Optional) Main Power - White Ground Stud Ignition On - Red Glow Plug - Green Start - Black Drive Lights - Blue Hi-Low - Yellow Not Used - Brown 5 Amp Oil Pressure - Brown Low Hydraulic - Green Temp - Red Level - Yellow 4 11 Off ACC Hours Glow Ign Start Cat/Perkins Tier II Engine Dash Wiring BOM Tucker # Qty 1 Key Sw itch CH Hour Meter GBI Push-Pull Waytek 4 Fuse Panel Terminal Strip v LED Wiper Sw itch Option Wiper Motor Option Wiper Arm Option Wiper Blade Option Work Light Cab Heater Option Wire 120 Ohn Resistor Assy Push/Pull Push/Pull 3 Work Lights Drive Lights Wiper (Option) Push/Pull Hi-Low Speed Oil Pressure Temp Low Hydraulic Hydraulic Oil Pres Temp Low Dash Closed Heater (Optional)

7 Fuel Lift Neutral Start Sunstrand # 80020S40 Tucker # High/Low Terminal G Fuel Pump Terminal 5 Red Black 64" High/Low Ground to Engine BU Alarm Fuse Fuel Thermostat Terminal 7 Fuel Lift Terminal 7 Glow Plug Terminal I Neutral Start Terminal 1 Neutral Start Terminal E #12 White 86" 13" Ext #14 Red 80" 12- Ext #18 Blue 98" 9-¾ Ext #12 Yellow 100" 11-½ Ext #14 Red 63" 12- Ext #14 Gray 66" 11- Ext #10 Red 62" 9" Ext #18 Blue 96-" 8- Ext 3/4 Glow Plug #10 Red 3/4 Fuel Thermostat HS #14 Red 3" Fuel Pump Black Gray 5" 1/4 5" 14-1/4 2- #18 Brown 7" HS 2" BU Alarm Preco Model 6003 Tucker # #12 White 82" 1/4 21" 3/8 HS #12 Black 14" 4" Blue 4" 6- Blue #14 Black 82" 14" Ext #14 Black 66" 11-3/4" Ext 44" ¾ #12 Black 14" #12 Yellow HS HS Fuel Lift Fuel Pump 11- Oil Pressure Terminal 9 #18 Brown 78" 12- Ext BU Alarm Switch Hobbs # N/O Tucker # #12 White #12 White High/Low Speed Selector HydraForce SV T-12DS Tucker # 80202

8 224 HS Drive Lights Main Power 5/16 Start Signal 1/4 HS #8 Red #10 Red #12 Red 14-¾ ¾ #12 Blue 3/ /4 9- ¾ 3/4 #8 Red 31" 5- Ext Circuit Breaker 1/4 ** #12 Red Ext Starter Terminal 2 5/16 HS #8 Black 9-3/8" #12 Blue 255 9" Ext #8 Black 42" 11-¾ Ext #10 Charging From Alt. 5/16 #10 Red 28" 1- Ext Fuse Block Ground Ground Starter / Charging Wire Assembly W2 Alternator Charging Post 1/4 HS Drive Lights Terminal F

9 #18 Black 12" #18 Red HS HS NC C NO Temp Switch Murphy # TSB-R220F/104C- Tucker # / ¾ 3/4 #18 Black 15" 4-" Ext #18 Black 24" 7-1/4" Ext Temp Terminal 10 #18 Red Ext #18 Gray 32" 15- Ext #18 Yellow 33-17" Ext #14 Red 36" 18" Ext Level Terminal 5 Level Terminal 11 12" 3/8" #14 Red Gray Black Temp Level Alternator Terminal C 3 4 Yellow Alternator Excite Level To Level Switch Kohler # Tucker #

10 3/8" Synflex 83" Ground Terminal Black #18 Black 97" Green #18 Green 103" Hydraulic Oil Level Terminal 8 Hydraulic Oil Level Sensor