CP-8301-xxx Series. Application. Features. Applicable Literature. 1 to 15 Vdc Input Electronic Actuator Drive General Instructions
|
|
|
- Thomasine Hensley
- 6 years ago
- Views:
Transcription
1 CP-80-xxx Series to 5 Vdc Input Electronic General Instructions Application The CP-80-xxx Series electronic actuator drive is designed to process a variable to 5 Vdc signal from a controller to provide proportional control of an electric gear train actuator. Features Mounts directly onto Schneider Electric proportional, electric, gear train actuators. Fixed to 5 Vdc operating range., 0, and 0 Vac models available. Color-coded pigtail leads. Applicable Literature Environmental Controls Cross-Reference Guide, F-68 Environmental Controls Reference Manual, F-68 Environmental Controls Application Manual, F-5 Pneumatic Products Catalog, F-78 MP-xx Series, MP-xx Series, MP-xxx Series, and MP-xxx Series Reversible and Proportional Electric s General Instructions, F-579 Printed in U.S.A. / Copyright 0 Schneider Electric All Rights Reserved. F-90-8
2 SPECIFICATIONS Inputs Control Signal: Range, to 5 Vdc, nonadjustable. Span, Refer to Table-. Start Point, Refer to Table-. Power Requirements: Refer to Table-. Power Supplies: Refer to Table-. Outputs Connections: Color-coded pigtail leads. Mounting: Directly to an actuator. The upright position is preferred, but other positions are acceptable. Case: Black Phenolic - IDI -0 5VA - RoHS Compliant. Environment Ambient Temperature Limits: Shipping & Storage, -0 to 60 F (-0 to 7 C). Operating, -0 to 0 F (-0 to 60 C). Humidity: 5 to 95% relative humidity, non-condensing. Locations: NEMA Type. Agency Listings US Standard UL 87: Underwriters Laboratories (File #E99 Category XAPX, Temperature Indicating and Regulating Equipment). Canadian Standard C. No. : Underwriters Laboratories (File #E99 Category XAPX7, Temperature Indicating and Regulating Equipment). Table- Specifications. Power Requirement Part Number Vac,.8 VA 50/60 Hz (+0/-5%) CP-80-0 CP CP Power Supply b 0 Vdc, 50 ma regulated and filtered Start Point of Adjustable a from to Vdc input Factory-set at 6 Vdc a Remove the company logo, then turn the start point potentiometer CW to increase the start point. b The power supply must not be connected to the +0 (red) of other supplies. Span Fixed at Vdc for full actuator stroke Table- Typical s. Power Torque Stroke Spring Internal Series 60 Hz Amp Lb-in. N-m Degrees Return Transformer a MP No MP CW No MP CCW No MP No MP Yes MP CW Yes MP CCW Yes MP Yes MP Yes MP Yes MP Yes a Units with a - suffix, e.g. MP-xxxx-xxx--x, include a built-in transformer (used for Barber-Colman Microtherm or with AE-50) with secondary leads wired externally to terminals seven and eight of the actuator. Red ( Vac) to terminal eight and Blue ( Vac) to terminal seven. When these actuators are used with controllers other than Barber-Colman Microtherm or AE-50, disconnect the Red and Blue leads and tape off. Note: Models prior to - suffix had transformer wired directly to potentiometer. To disconnect the transformer, remove the back plate of the actuator, disconnect and tape the transformer leads. Copyright 0 Schneider Electric All Rights Reserved. F-90-8
3 ACCESSORIES None TYPICAL APPLICATIONS (wiring diagrams) TOOLS Appropriate screwdriver TOOL-0 Calibration kit for System 8000 TM products. Refer to Figure- for a service application wiring diagram showing the connections between a CP-80-xxx series drive and an MP-xx, MP-xx or MP-xx series actuator. CP-80-XXX Yellow Blue Red Brown/White Brown Brown/Black Red/Black Blue/Black Yellow/Black Green/Yellow MP-XX, MP-XX, MP-XX Series Yellow (OP) Wire Nuts Blue (COM) Red (+0) Terminals x Ohm Slidewire Limit Switches Typical Controller TP-80 CP-80 Shading Windings Field Winding Part Number Vac Color CP-80-0 Black/Blue CP White CP White/Black Black L (H) L (G) Power For actuator with internal transformers. Disconnect red and blue leads from actuator terminals 7 and 8 and tape off. Diagram shown: increasing input causes CW actuator rotation. All references to the direction of rotation are determined by looking at the actuator output shaft. For CCW rotation with an increasing input signal, reverse the wires to terminals 7 & 8 and &. Connect Green/Yellow ground wire from CP actuator drive to case ground screw. Figure- Service Application Wiring Diagram. INSTALLATION Inspection Requirements Inspect the package for damage. If damaged, notify the appropriate carrier immediately. If undamaged, open the package and inspect the device for obvious damage. Return damaged products. Tools (not provided): Appropriate screwdriver Digital Volt-ohm Meter (DVM) Training: Installer must be a qualified, experienced technician Other accessories as appropriate Wiring diagrams F-90-8 Copyright 0 Schneider Electric All Rights Reserved.
4 Warning: Electrical shock hazard! Disconnect power before installation to prevent electrical shock or equipment damage. Make all connections in accordance with the electrical wiring diagram and in accordance with national and local electrical codes. Use copper conductors that are suitable for 75 C. Caution: Do not exceed the ratings of the device(s). Static charges produce voltages high enough to damage the electronic components. Follow static electricity precautions when installing or servicing the device(s). Discharge any static electricity you may have accumulated. Discharge static electricity by touching a known, securely grounded object. Avoid locations where excessive oil, dust, moisture, corrosive fumes or vibration, or an explosive atmosphere is present. Mounting Upright mounting of the drive is preferred, but other positions are acceptable. Mount the drive onto an actuator as follows:. Insert the drive s two /" conduit connectors into the two /" knockouts provided on the actuator casing. Refer to Figure-, Figure-, and Figure-5. Left-Side Mounting (Optional) Right-Side Mounting (Typical) Figure- Mounting Position of on. Caution: The power wires must always be inserted directly into the power wiring compartment of the actuator. If the optional mounting position for the drive (refer to Figure-) is used, it is required that the wires of the drive are routed to exit through its other conduit bushing.. Secure the drive to the actuator with the two locknuts provided. Refer to Figure-. Copyright 0 Schneider Electric All Rights Reserved. F-90-8
5 Power Wiring Compartment L (H) L (G) Barrier To Controller L (H) 5 L (G) 6 8 x 7 Location of Start Point Adjustment Potentiometer Low Voltage Wiring Compartment Top view. Remove green wire from terminal X. Right-side mounting is shown. Connect Green/Yellow ground wire from CP actuator drive to case ground screw. Figure- / Wiring and Mounting Arrangement. WIRING Power Wiring All the power to the drive is supplied by the electric actuator onto which the drive is mounted. Refer to Figure-. Refer to Table- for power wire selection. Table- Power Wire Selection. Voltage Vac 0 0 Wire Size AWG Maximum Run (each run has two wires) ft (m) 0 () 5 (76) 00 (60) All the applicable actuators have a barrier that separates the power wiring compartment from the low voltage wiring compartment. The power wiring for the Vac actuators may be per Class circuit requirements if the auxiliary switch (terminals one, five, and six) is Vac, or is not used. The power wiring must be per Class circuit requirements if the actuator is line voltage or if the auxiliary switch is powered by line voltage. The connections to the low voltage wiring compartment may be per Class circuit requirements. Input Wiring The drive s two input wires, which must be connected to the controller, are color-coded blue (COM) and yellow (OP). Refer to Figure-. Use 8 gage, three-conductor, twisted leads (part number W-0) for runs of up to 000 ft. (05 m) between the controller and the actuator. Use larger-sized leads for longer runs. Caution: Use 8 gage, shielded, twisted cable when it is necessary to install the signal leads in the same conduit with the power wiring, or when high RFI/EMI generating devices are near. Terminate the shielding on the signal leads at one end only, using the controller s COM (negative) terminal. Grounding the shielding at both ends could create a potential difference in the shielding, which may affect the signal voltage carried by the leads. F-90-8 Copyright 0 Schneider Electric All Rights Reserved. 5
6 Green / Yellow Yellow / Black Blue / Black Red / Black Brown Red Red (+0) Yellow Yellow (OP) Blue Blue (COM) X 8 H G Brown / White Brown / Black Black CP-80-XXX Typical Controllers TP-80 CP-80 AC Supply CP-80-0 can be used with the following electric actuators: MP-6, 7, 8, 8, -500 and 97. CP-80-0 can be used with the following electric actuators: MP-65, 75, 8, 85, 86, 95, and CP-80-0 can be used with 0 Vac electric actuators. (Available as a standard option.) rotates clockwise on increase in input signal. To rotate actuator counterclockwise on an increase in input signal, reverse blue/black and red/black leads and reverse brown/black and brown/white leads. Vac s Only. 6 5 Part Number Vac Color CP-80-0 Black/Blue CP White CP White/Black These terminals are marked L & L on 0V and 0V actuators. 0V and 0V actuators must not have a built-in transformer, or if a built-in transformer is present, remove red and blue leads from terminals 7 and 8, and tape off. External green jumper from X to case ground (and G to case ground, for Vac) on MP-XXXX-XXX-X- models only. Connect green/yellow ground wire from CP actuator drive to case ground screw. Figure- Installation Wiring Diagram. ADJUSTMENTS Start Point Adjustment The start point of these actuators is factory-set to 6 Vdc and is field-adjustable from to Vdc. If a start point other than 6 Vdc is required, proceed as follows:. Peel back the Schneider Electric label from the drive, to expose the start point adjustment potentiometer. Refer to Figure-.. Disconnect the red, yellow, and blue leads of the drive from the controller.. Connect the leads of TOOL-0 to the like-colored leads of the drive.. Connect a DVM to the yellow (OP) and blue (COM) leads of the drive. 5. Adjust TOOL-0 until the DVM reading equals the required start point voltage ( to Vdc). 6. Adjust the actuator start point, using a small, single-slotted screwdriver, so that the actuator shaft just begins to rotate when the desired voltage is applied. 7. Press the label back onto the drive. CHECKOUT After the entire system has been installed and the actuator has been powered up, the following checks can be made for proper system operation. Positioning with Controller If the sensed media is within the controller s setpoint range, the actuator can be positioned by adjusting the controller setpoint up and down. Check for correct operation of the actuator (valve or damper) while it is being stroked. 6 Copyright 0 Schneider Electric All Rights Reserved. F-90-8
7 Go, No Go Test Manual Positioning. Disconnect the field wiring from the red, yellow, and blue leads of the drive.. Apply power to the actuator.. Short the yellow and red leads of the drive. The actuator should rotate CW to its limit, unless it is rewired to rotate CCW on an increase in input signal. Disconnect the short between the yellow and red leads.. Short the yellow and blue leads of the drive. The actuator should rotate CCW to its limit, unless it is rewired to rotate CW on an increase in input signal. Disconnect the short between the yellow and blue leads. 5. If the assembled actuator and drive passes steps and, they are functioning correctly. If the assembly does not pass these steps, proceed to the next step. 6. Unhook the drive leads from actuator terminals x,, and. 7. Short actuator terminals x and two. The actuator should rotate CW to its limit. Disconnect the short. The actuator should stop rotation. 8. Short actuator terminals x and three. The actuator should rotate CCW to its limit. Disconnect the short. The actuator should stop rotation. 9. If the actuator passes steps 7 and 8, it is functioning correctly. If the actuator does not pass these steps, the drive may still be functional but the actuator must be replaced.. Apply power to the actuator.. Disconnect the actuator s control leads from the controller.. Attach the leads from the manual positioner (TOOL-0) to the like-colored leads on the drive.. Manually position the actuator by turning the knob of the manual positioner. 5. Check for proper operation of the valve or damper as the actuator is operated. 6. Remove power from the actuator. 7. Reconnect the actuator wires to the controller. F-90-8 Copyright 0 Schneider Electric All Rights Reserved. 7
8 MAINTENANCE The drive requires no maintenance. Regular maintenance of the total system is recommended to assure sustained, optimum performance. FIELD REPAIR None. Replace an inoperative drive with a functional unit. DIMENSIONAL DATA " (0mm) -7/8" (8mm) -/" (8mm) -/" (6mm) " (5mm) /" Conduit Thread " (0mm) Figure-5 Mounting Dimensions of CP-80-xxx Series Electronic. Copyright 0, Schneider Electric All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. F-90-8 Schneider Electric 5 Clifford Avenue P.O. Box 90 Loves Park, IL
CP-9301 CP Application. Features. Applicable Literature. Electronic Actuator Drives General Instructions
CP-90 CP-90 Electronic Drives General Instructions Application The CP-90 and CP-90 electronic actuator drives process a variable input signal from a controller to provide proportional control of an electric
CP (Vdc) CP (Milliamp) CP (Slidewire)
CP-91-456 (Vdc) CP-91-716 (Milliamp) CP-91-717 (Slidewire) Electronic General Instructions Application Electronic actuator drive is used to provide proportional control of an electric gear train actuator
MP-5400 Series. Application. Features. Applicable Literature. Electronic Positive Positioning Hydraulic Actuator General Instructions
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com MP-5400 Series Electronic Positive Positioning Hydraulic Actuator General Instructions Application The MP-5400 Series Actuators
MA-5200 Series MA-5300 Series
MA-5200 Series MA-5300 Series Two-Position Actuators General Instructions Application The MA-5200 series and MA-5300 series actuators are used for two-position control of valves and dampers which require
CP CP
Electronic Drive General Instructions Application Electronic actuat drive is used to provide proptional control of an electric gear train actuat from a variable voltage DC signal from a controller. Features
MP-5200 Series. Application. Features. Applicable Literature. Electronic Hydraulic Actuator General Instructions
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com MP-5200 Series Electronic Hydraulic Actuator General Instructions Application The MP-5200 Series actuators are for the electronic
MAx-305 & MAx-318 Series MAx-405 Through MAx-419 Series Two-Position Actuators
MAx-305 & MAx-38 Series MAx-405 Through MAx-49 Series Two-Position Actuators General Instructions Application For two-position operation of dampers, valves, and other equipment which require the return
SLC-811X Series. Single Loop Proportional Temperature Controller General Instructions APPLICATION SPECIFICATIONS
SLC-811X Series TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com Single Loop Proportional Temperature Controller General Instructions APPLICATION Electronic temperature controller
TS , -850 Series TS , -850 Series TS-57031, TS
TS-5711-770, -850 Series TS-57011-770, -850 Series TS-57031, TS-57031-850 Electronic Room Temperature Sensors General Instructions Application These sensors provide electronic sensing of room temperature
MF4E MF4E
MF4E-60830-100 TAC DuraDrive Non-Spring Return Floating Actuator General Instructions Application The 35 lb-in. (4 N-m) and MF4E-60830-100 70 lb-in. (8 N-m) non-spring return, direct-coupled actuators
CP-8551 & CP Application. Features. Applicable Literature. Electronic to Pneumatic Transducers General Instructions
CP-8551 & CP-8552 Electronic to Pneumatic Transducers General Instructions Application The CP-8551 and CP-8552 transducers receive a variable electronic input signal and produce a 3 to 15 psig (21 to 103
MS Application. Features. Proportional Valve Actuator General Instructions
Proportional Valve Actuator Application The Proportional Valve Actuator is a non-spring return actuator used with proportional to 10 Vdc or 4 to 0 ma controllers and standard 1/" to 1-1/4" two-way and
THC-2, THC-3, THCR-4, THCR-5. Enthalpy Control. General Instructions APPLICATION SPECIFICATIONS. ACCESSORIES None
THC-2, THC-3, THCR-4, THCR-5 Enthalpy Control General Instructions APPLICATION For ON-OFF (two position) low voltage control of the amount of air brought into the cooling system with respect to the total
MF-22xx3. Application. Features. Floating Valve Actuator General Instructions
MF-22xx3 Floating Valve Actuator Application The Floating Valve Actuator is a non-spring return actuator used with floating DDC controllers and standard /2" to -/4" two-way and three-way valve bodies for
AV-430. Application. Features. Applicable Literature. Valve Linkage for Pneumatic Actuators General Instructions
AV-430 Valve Linkage for Pneumatic s General Instructions Application The AV-430 valve linkage is used to field assemble MK-66X1, MK-68X1, and MK-6911 actuators, as well as the obsolete MK-47X1 actuators,
AV-401. Application. Features. Applicable Literature. Pneumatic Actuator Valve Linkage Kit General Instructions
AV-401 Pneumatic Actuator Linkage Kit General Instructions Application The AV-401 valve linkage kit is used to field assemble MK-4600 series pneumatic actuators to a variety of 1/2" through 2" valve bodies.
453X Series. Application. Features. Two-Position Damper Actuator General Instructions
453X Series Two-Position Damper Actuator General Instructions Application The 453L, light duty damper actuators are designed for a variety of two-position, spring return, damper applications. The 453L
AM-751, AM-752, AM-753, AM-754, AM-755. Applications. Applicable Literature
AM-751, AM-752, AM-753, AM-754, AM-755 For Schneider Electric DuraDrive 150 in-lb Spring Return and 300 in-lb Non-Spring Actuators General Instructions Applications The AM-751 and AM-752 anti-rotation
TS Series TS Series
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com TS-6700-850 Series TS-5700-850 Series Electronic Remote Temperature Sensors General Instructions APPLICATION Electronic thermistor
M100F Incremental Motor Actuator R81F Interface Board
Installation Sheets Manual 121 Motor Actuators Section M Technical Bulletin M100F Issue Date 0493 M100F Incremental Motor Actuator R81F Interface Board Application Details Figure 1: M100 Motor Actuator
IMP-5400 Series. Application. Features. Applicable Literature. Electronic Positive Positioning. Hyciraulic Actuator General Instructions SIEBE
n@ SEBE Siebe Environmental Controls 1354 Clifford Avenue (Zip 61111) PO Box 2940 Loves Park, L 61132-2940 nvensys Building Systems, nc 1354 Clifford Avenue PO Box 2940 Loves Park, L 61132-2940 wwwinvensysibscom
MK-6600 Series, MK-6800 Series, and MK-6911
MK-6600 Series, MK-6800 Series, and MK-6911 Pneumatic Valve Actuators General Instructions Application These valve actuators, with a 50 sq. in. (323 cm 2 ) effective diaphragm area, are used for proportional
AV-497. Application. Features. Valve Linkage for MK-6811 and MK-6911 General Instructions
AV-497 Valve Linkage for MK-6811 and MK-6911 General Instructions Application The AV-497 valve linkage kit is used to field assemble MK-6811 actuators onto 2-1/2 to 5 VB-8xxx series valves and MK-6911
AK Application. Features. Applicable Literature. Positive Positioner Pneumatic Relay General Instructions
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com Positive Positioner Pneumatic Relay General Instructions Application The Positive Positioner Pneumatic Relay is used to accurately
MC-351, 421, 431, MC-4311
MC-35, 42, 43, MC-43 Three-Wire, Two Position Actuators General Instructions Applications For two-position operation of dampers or valves in heating, ventilating and air-conditioning systems and similar
MA40-704X Series MA41-707X Series MA41-715X Series
MA4-74X Series MA4-77X Series MA4-75X Series SmartX Actuators Spring Return Two-Position General Instructions Application SmartX Direct Coupled Actuators are designed to be used in both damper and valve
SPECIFICATIONS ATTENTION OPERATION DESCRIPTION
EMP-5 Installation Manual - P/N 80103 - Ed. 01/09 EMP-5 Current or Voltage Input Drive Modulating Actuator Installation Instructions 1 7 SPECIFICATIONS The EMP-5 series actuators provide damper control
T500 Series. Applications. Features. Applicable Literature. Non-Digital, On/Off Thermostat General Instructions
T500 Series Non-Digital, On/Off Thermostat General Instructions Applications The T500 series thermostats are available in four basic models for low and line voltage control of valves, relays, and fan motors
Instruction Manual for Barber-Colman Series EA Electric High Torque Actuators
Instruction Manual for Barber-Colman Series EA Electric High Torque Actuators 1321-IN-004-0-11 For use with VB-7000 and VB-9000 Valve Bodies from Barber-Colman, and other commercially available rotary
MS40-717X Series. Application. Features. DuraDrive Series Spring Return Proportional Actuators General Instructions
MS40-77X Series DuraDrive Series Spring Return Proportional Actuators General Instructions Application DuraDrive Direct Coupled Actuators are designed to be used in both damper and valve control applications.
MX4X-6XXX Series MX4X-7XXX Series. Selection Guide. Applications. DuraDrive Series Actuators and Accessories
MX4X-6XXX Series MX4X-7XXX Series Selection Guide DuraDrive Series Actuators and Accessories Applications DuraDrive Direct Coupled Actuators are designed to accept two-position, floating, or proportional
TK-6024, TK-6124, TK-8024, TK-8124
TK-6024, TK-6124, TK-8024, TK-8124 Pneumatic Bulb Thermostats General Instructions APPLICATION For proportional temperature control of pneumatic valves and actuators to maintain air or liquid temperatures
AV-611. Application. Applicable Literature. Schneider Electric DuraDrive Globe Valve Linkage General Instructions
AV-611 Schneider Electric DuraDrive Globe Valve Linkage General Instructions Application The AV-611 linkage is designed to link the Schneider Electric DuraDrive Mx41-6xx3 non-spring return and Mx40-704x
TSMN-90xxx Series TSMN TSMN TSMN Electronic Room Temperature Sensor General Instructions
TSMN-90xxx Series TSMN-57011-850-0-01 TSMN-58011-000-0-01 TSMN-81011-000-0-01 Electronic Room Temperature Sensor General Instructions Application The Electronic Room Temperature Sensor is a resistance-temperature
2211 Series. Application. Features. One-Pipe Pneumatic Room Thermostats General Instructions SPECIFICATIONS
TAC 1354 Clifford Avenue P. O. Box 940 Loves Park, IL 6113-940 www.tac.com 11 Series One-Pipe Pneumatic Room s General Instructions Application The 11 Series Pneumatic Room is designed for proportional
VA-4233-GGx Series Electric Valve Actuators
Installation Instructions Issue Date August 11, 2003 VA-4233-GGx Series Electric Valve Actuators Installation Refer to Figures 2 through 4 for proper actuator orientation before attempting to make the
MS Series MS Series MS Series
MS4-743 Series MS4-773 Series MS4-753 Series SmartX Actuators Spring Return Proportional General Instructions Application SmartX Actuators (Direct Coupled) are designed to be used in both damper and valve
VB-8000 Series VB-9313 Series. Selection Guide. Applications. Applicable Literature. Selection Guide Contents. Valve and Actuator Selection Procedure
Selection Guide VB-8000 Series VB-9313 Series Schneider ElectricVB-8000 Series and VB-9000 Series 2-1/2 to 6 Globe Valves with Schneider Electric NSR Forta M800A and M1500A Actuators Applications Schneider
Damper Actuator Installation
FANs 268.1, 977, 1628.3 Installation Bulletin EPP-1000 Issue Date 0800 EPP-1000 Series Electro-Pneumatic Positioners A pplication The EPP-1000 is designed for applications where electronic control of pneumatic
MF Series MS Series
MF41-6043 Series MS41-6043 Series DuraDrive Non-Spring Return Direct Coupled Actuator General Instructions Figure-1 Parts of the DuraDrive Rotary Actuator. Product Description These installation instructions
MF Series MF Series MF Series
MF40-7043 Series MF41-7073 Series MF41-7153 Series SmartX Actuators Spring Return Floating General Instruction Application Schneider Electric Direct Coupled SmartX Actuators are designed to be used in
TAC DuraDrive Product Guide Direct Coupled Actuators
TAC DuraDrive Product Guide Direct Coupled Actuators SPRING RETURN TAC DuraDrive Spring-Return Direct Coupled Actuators TAC OFFERS A COMPLETE LINE OF DIRECT COUPLED ACTUATORS FOR ALL YOUR SPRING RETURN
MA/F/S 4D-xxxx-xxx Two Position, Floating and Proportional Series SmartX Actuators Rotary Overshaft Actuators
Installation Instructions MA/F/S 4D-xxxx-xxx Two Position, Floating and Series SmartX Actuators Rotary Overshaft Actuators schneider-electric.com Application Rotary overshaft SmartX Actuators provide an
ComfortPoint Programmable Lon, VAV/Unitary Controllers
ComfortPoint Programmable Lon, VAV/Unitary Controllers Controller Model Programmable Type Universal Inputs (UI) Table 1. Controller configurations. Digital Inputs (DI) PRODUCT DESCRIPTION INSTALLATION
MS41-634X Series. Features. SmartX Actuators Non-Spring Return Proportional General Instructions
MS4-634X Series SmartX Actuators Non-Spring Return Proportional General Instructions Application Direct Coupled SmartX Actuators are designed to be used in both damper and valve control applications. The
System 350 S350P Proportional Plus Integral Temperature Stage Module
FANs 930, 930.5 Add-On Modules Section Product/Technical Bulletin S350P Issue Date 0997 System 350 S350P Proportional Plus Integral Temperature Stage Module The S350P is used in conjunction with the A350
Non-Spring Return EconoDrive Floating Actuator
MF4D-0x Series Non-Spring Return EconoDrive Actuator EconoDrive overshaft actuators are designed to provide an economical and reliable solution for many overshaft damper and ball valve requirements. All
Selection Guide. Vx-2x13-5xx-9-xx Series Vx-2x13-8xx-9-xx Series VB-2x xx Series. Schneider Electric Ball Valve Assemblies
Vx-2x3-5xx-9-xx Series Vx-2x3-8xx-9-xx Series VB-2x3-500-9-xx Series Selection Guide Schneider Electric Ball Valve Assemblies The Schneider Electric VA, VF, and VS-2x3-xxx-9-xx series Ball Valve Assemblies
Series 71, 72, and 76 Modutrol IV Motors
Series 7, 7, and 76 Modutrol IV Motors PRODUCT DATA FEATURES APPLICATION The Series 7, 7 and 76 Modutrol IV Motors are spring return and nonspring return motors used to control dampers and valves. The
VB-9323 Series. Application. Features. Applicable Literature. 2-1/2" to 6" 125 Lb. Flanged Three-Way Diverting Valves General Instructions
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com VB-9323 Series 2-1/2" to 6" 125 Lb. Flanged Three-Way Diverting Valves General Instructions Application VB-9323 series three-way
VA-715x Electric Valve Actuator
Product/Technical Bulletin VA-7150 Issue Date 0513 VA-715x Electric Valve Actuator The VA-715x Series synchronous motor-driven actuator provides incremental (three wire), incremental with feedback, or
Series EA High Torque Actuators with Integrated Controller
Copyright September 2000 Barber-Colman Company Series EA High Torque Actuators with Integrated Controller 1321-IN-013-0-00 Contents 1. Introduction... 2 2. Specifications... 3 3. Model Number... 4 4. Installation...
MX4X-6XXX-20X Series MX4X-7XXX-20X Series
MX4X-6XXX-20X Series MX4X-7XXX-20X Series SmartX Actuator/Linkage Assemblies for Globe Valves General Instructions Application The actuator/linkage assemblies are mounted onto globe valves to control the
35 and 70 lb-in. Non-Spring Return Direct Coupled Actuators ML6161, ML7161, ML6174, ML7174
35 and 70 lb-in. Non-Spring Return Direct Coupled Actuators ML66, ML76, ML674, ML774 PRODUCT DATA FEATURES Selectable 45,, or 90 stroke in both clockwise (cw) or counterclockwise (ccw) directions. 0 to
Application. Features
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com MAx1-720x Two Position Series MFx1-7203 Floating Series MSx1-7203 Proportional Series TAC DuraDrive Linear Series Spring Return
Invensys Energy Solutions 1354 Clifford Avenue (Zip 61111) P.O. Box 2940 Loves Park, IL United States of America
Invensys Energy Solutions 5 Clifford Avenue (Zip 6) P.O. Box 9 oves Park, I 6-9 United States of America www.ies.invensys.com MX-7X Series DuraDrive Series 5 lb-in. Spring eturn Actuators Mounting and
Powers TM Controls EA 338 Electronic Actuator
Powers TM Controls Technical Instructions Document No. 155-136P25 EA 338-1 Description Features 24 Vac power supply. The s are used with floor mount linkage kits to operate dampers in HVAC installations.
Installation Instructions
Quick-Mount Visual Instructions for Quick-Mount Visual Instructions 1. Rotate the damper to its failsafe position. If the shaft rotates counterclockwise, mount the CCW side of the actuator out. If it rotates
Installation Instructions
Quick-Mount Visual Instructions for Mechanical Installation Quick-Mount Visual Instructions 1. Rotate the damper to its failsafe position. If the shaft rotates counterclockwise, mount the CCW side of the
M9106-AGx-2N0x Series Electric Non-spring Return Actuators
Installation Instructions M9106AGx-2N0x Issue Date 08/31/01 M9106-AGx-2N0x Series Electric Non-spring Return Actuators Installation IMPORTANT: The M9106-AGx-2N0x Series actuator is intended to control
Technical Instructions Flowrite 599 Series SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Description Features Application
Document No. 155-180P25 Flowrite 599 Series SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Description The Flowrite 599 Series SKD6xU Electronic Valve Actuators require a 24 Vac supply and
MS4104, MS4109, MS4604, MS4609, MS8104, MS8109 Fast-Acting, Two-Position Actuators
MS4104, MS4109, MS4604, MS4609, MS8104, MS8109 Fast-Acting, Two-Position Actuators FOR FIRE/SMOKE CONTROL APPLICATIONS FEATURES PRODUCT DATA APPLICATION The MS4104, MS4109, MS4604, MS4609, MS8104 and MS8109
D-70, D-140, D-210, and D-280 Series Electric Non-Spring Return Actuators
Installation D-70, D-140, D-210, and D-280 Series Electric Non-Spring Return Actuators IMPORTANT: The D- Series actuators are intended to control equipment under normal operating conditions. Where failure
M9206-Bxx-2S Series On/Off Electric Spring Return Actuators
Installation Instructions M9206-Bxx-2S Issue Date May 14, 2003 M9206-Bxx-2S Series On/Off Electric Spring Return Actuators Installation IMPORTANT: Use this M9206-Bxx-2S Series actuator to control equipment
M9216 Series Electric Spring Return Actuators
*34636461G* 34-636-461, Rev. J Installation Instructions M9216 Issue Date October 217 M9216 Series Electric Spring Return Actuators Installation IMPORTANT: The M9216 Series actuator is intended to control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control Technical Instructions Document No. 155-313P25 EA 599-15 EA1157R1 Description The Powermite 599 MT SSC61U and SSC61.5U
Flowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac 3-Position (Floating) Control
Flowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac 3-Position (Floating) Control Technical Instructions EA 599-5 Description The Flowrite EA 599 Series SKD electronic valve actuator requires a
AV-608 Linkage Adapter Kit
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com AV-608 Linkage Adapter Kit Adapter for AV-607 TAC DuraDrive Linkage, MX-6XXXX Jackscrew Style Actuators, and VB-9XXX 1-1/2"
OpenAir Electronic Damper Actuators GLB Series Enhanced Non-spring Return Rotary
Document No. 155-785 OpenAir Electronic Damper Actuators GLB Series Enhanced Non-spring Return Rotary Description The OpenAir direct coupled enhanced non-spring return rotary electric actuators are designed
Flowrite EA 599 Series SQX Electronic Valve Actuator 24 Vac, 3-Position Control
Flowrite EA 599 Series SQX Electronic Valve Actuator 24 Vac, 3-Position Control Technical Instructions EA 599-7 Description The Flowrite EA 599 Series SQX electronic valve actuator requires a 24 Vac supply
Series 41 and 81 Modutrol IV Motors
Series 4 and 8 Modutrol IV Motors PRODUCT DATA FEATURES APPLICATION The Series 4 and Series 8 Modutrol IV Motors are 2-position (line- and low- voltage control, respectively) spring-return motors. They
System 350 P352AB Electronic Pressure Control Series
System 350 P352AB Electronic Pressure Control Series System 350 Product Guide 930 Basic Controls Section Product/Technical Bulletin P352AB Issue Date 0200 The P352AB controls are On/Off electronic pressure
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control Document No. 155-313P25 EA 599-15 Description The Powermite 599 MT SSC61U and SSC61.5U series of electronic valve actuators
MAx1-720x Two Position Series MFx Floating Series MSx Proportional Series
MAx-70x Two Position Series MFx-703 Floating Series MSx-703 Proportional Series SmartX Actuators Linear Spring Return General Instructions Application Linear SmartX Actuators are designed to mount directly
DA-053 Series. Overview. Applications. Features & Benefits. Datasheet. 53lb-in (6 Nm), Non-Spring Return Damper Actuators
Datasheet 53lb-in (6 Nm), Non-Spring Return Damper Actuators Overview The direct-coupled fail-safe/failin-place electronic actuators are designed for modulating, two position, and floating control of laboratory
Q7130A, Q7230A, Q7330A Modutrol IV Interface Modules
Q70A, Q70A, Q70A Modutrol IV Interface Modules EATURES INSTALLATION INSTRUCTIONS Q70A APPLICATION Q70A Q70A The Q70, Q70, and Q70 Modutrol IV Interface Modules are used with Series 90 Modutrol IV Motors
VA, VF, and VS Series Direct Mounted Globe Valve Assemblies. Application. Features
TAC 1354 Clifford Avenue P.O. Box 2940 Loves Park, Illinois 61132-2940 www.invensysibs.com Two-Way and Three-Way Globe Valve Assemblies with 220 lbf Linear (979 N) Spring Return DuraDrive Actuators Submittal
Flowrite 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control
Document No. 155-171P25 Flowrite 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control 8Description The Flowrite 599 Series SKB/C electronic valve actuator requires a 24 Vac
VA-4233-AGx Series Electric Valve Actuators
Installation Instructions VA-4233 No. 1 Issue Date June 30, 2014 VA-4233-AGx Series Electric Valve Actuators Installation Refer to Figures 2 through 4 for proper actuator orientation before attempting
MA40-704X Series, MA4X-707X Series, MA4X-715X Series DuraDrive Series Spring Return Two-Position Actuators General Instructions
MA4-74X Series, MA4X-77X Series, MA4X-75X Series DuraDrive Series Spring eturn Two-Position Actuators General Instructions Application DuraDrive Direct Coupled Actuators are designed to be used in both
M9203-xxx-2(Z) Series Electric Spring-Return Actuators
Code No. LIT-1900682 Issued January 2, 2014 M9203-xxx-2(Z) Series Electric Spring-Return Actuators Description The M9203-xxx-2(Z) Series Electric Spring-Return Actuators provide control of dampers in HVAC
M436A/M836A,B Damper Motors
M436A/M836A,B Damper Motors FEATURES INSTALLATION INSTRUCTIONS APPLICATION M436A/M836A,B Damper Motors are spring return (SR) motors used for residential and light commercial applications in Series 40
MF /MS Series
MF41-6153/MS41-6153 Series 24 Vac, Three-position/Modulating Non-spring Return Rotary Electronic Damper SmartX Actuators General Instructions Description The direct-coupled, 24 Vac, non-spring return electronic
M9116, M9124, and M9132 Series Electric Non-spring Return Actuators
Product Bulletin M91xxx Issue Date September 2017 M9116, M9124, and M9132 Series Electric Non-spring Return Actuators The M91xx Series includes M9116, M9124, and M9132 models. All of these direct-mount
CENTRIFLOW METER and ELECTRONICS WIRING and INSTALLATION MANUAL REV 01/16 ORIGINAL LANGUAGE Copyright 2016 Eastern Instrument Laboratories, Inc. All Rights Reserved. TABLE OF CONTENTS SAFETY Safe Operation...
DuraDrive MF /MS Series Non-spring Return Rotary Electronic Damper Actuators 24 Vac Three-position/Modulating
General Instructions DuraDrive MF4-653/MS4-653 Series Non-spring Return Rotary Electronic Damper Actuators 4 Vac Three-position/Modulating Description The DuraDrive direct-coupled, 4 Vac, non-spring return
SAX Electronic Valve Actuator
SAX Electronic Valve Actuator Non-spring Return, 24 Vac, Proportional Control Technical Instructions Document No. 155-506 Description The SAX Non-spring Return (NSR), Electronic Valve Actuator requires
Installation Manual. Mixing Box Control Systems Installation, Operation, and Maintenance Manual. 605 Shiloh Road Plano, Texas
Installation Manual IOM-MBC-00 08-30-04 Mixing Box Control Systems Installation,, and Maintenance Manual Contents Page Introduction...1 General...1 Safety...1 Inspection...1 Mixing Box Control Systems...2
Flowrite EA 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control
Flowrite EA 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control Document No. 155-171P25 EA 599-2 Description The Flowrite EA 599 Series SKB/C electronic valve actuator requires
OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary
EA GDE/GLB-2 OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary Description OpenAir non-spring return, 24 Vac, floating control, direct-coupled, actuators
ML6420, ML7420 Non-Spring Return Electric Linear Valve Actuators
ML640, ML740 Non-Spring Return Electric Linear Valve Actuators EATURES Quick and easy installation. No separate linkage required. Conduit connector is standard. No adjustments required. Low power consumption.
ML6420, ML7420 Non-Spring Return Electric Linear Valve Actuators
ML640, ML740 Non-Spring Return Electric Linear Valve Actuators EATURES Quick and easy installation. No separate linkage required. Conduit connector is standard. No adjustments required. Low power consumption.
Series BFM Bulk Flow Monitor 1A FUSE RED LED RELAY. Part Number BFM-1 BFM-2 BFM-3 BFS-1
Series Bulk Flow Monitor Specifications - Installation and Operating Instructions Bulletin FL-1-4x 3/4 CONDUIT KNOCKOUTS BFS 1A FUSE RED LED RELAY 5-9/64 [130.45] TRANSFORMER 3[76.20] GREEN LED 7 [177.80]
VA-715x Electric Valve Actuator
Product/Technical Bulletin VA-7150 Issue Date March 31, 2014 VA-715x Electric Valve Actuator The VA-715x Series synchronous motor-driven actuator provides incremental (three wire), incremental with feedback,
TC-200 Series. Application. Features. Applicable Literature. Single Bulb Thermostats General Instructions
T-200 Series Single ulb Thermostats General Instructions Application These units are used for on-off control of media temperature in ducts, tanks, etc. Features Mechanism enclosed in rugged die cast case
NFB24, NFB24-S, NFX24, NFX24-S On/Off, Spring Return, 24 V
NFB4, NFB4-S, NFX4, NFX4-S On/Off, Spring Return, 4 V Torque min. 90 in-lb, for control of air dampers Technical Data Power supply Power consumption Transformer sizing Electrical connection NFB4... NFX4...
12 Series Linear Actuators. Operation & Maintenance Manual, Analog Positioner Installation
12 Series Linear Actuators Operation & Maintenance Manual, Analog Positioner Installation 6810 POWERLINE DR.-FLORENCE, KY. 41042 - TELEPHONE 859-727-7890, TOLL FREE 1-800-662-9424 FAX. 859-727-4070, E-MAIL:
Flowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac Proportional Control
Flowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac Proportional Control Document No. 55-8P25 EA 599-4 EA379R Description The Flowrite EA 599 Series SKD Electronic Valve Actuator requires a 24
Reproduction or other use of this Manual, without the express written consent of Vulcan, is prohibited.
SERVICE MANUAL ELECTRIC BRAISING PANS (30 & 40 GALLON) VE30 VE40 ML-126849 ML-126850 VE40 SHOWN - NOTICE - This Manual is prepared for the use of trained Vulcan Service Technicians and should not be used
Powers TM Controls SW 141 Differential Static Airflow Switches
Powers TM Controls SW 141 Differential Static Airflow Switches Document No. 155-052P25 SW 1 0518 Description The SW 141 Airflow Switch senses static differential pressure and the diaphragm operated snap