EXEL Bringing New Pumping Technology

Transcription

1 Manual Airmix Catalog

2 EXEL Bringing New Pumping Technology 2 The most efficient manual production spray technology in the world. Absolutely Nothing Compares When looking for an outstanding finish at industrial production rates with unbelievable transfer efficiencies, nothing compares to the power of Airmix. Airmix is the oldest most proven medium pressure technology in the world with a 30 year track record of serving thousands of satisfied customers throughout the world. A great Airmix spray package requires different pieces working in harmony to deliver the concert performance that our customers have come to expect. The suction assembly is selected to remove large particles and balance the need to draw sufficient fluid while minimizing cleaning waste. The pump is carefully crafted to minimize pulsation, maintenance and again cleaning waste at just the right pressure and flowrate. The feed hoses have unique pulsation dampening properties to eliminate any subtle pulsation and deliver the air and fluid at minimal pressure loss. In the final act there is the gun, with dual filtering to remove all the fine particles and harmonizing the air with the fluid to deliver a spray performance that is unequal anywhere in the world. Airmix. Absolutely Nothing Compares

3 Table Of Contents The Benefits of Airmix 4-5 Airmix Spray Gun - MVX 5-6 Airmix Spray Gun - MXLT 7 Airmix Air Caps and Tips 8 Easy-To-Work With Airmix Package Selection Guide 9 EZMix Pump Pump Pump Pump Pump Pump Pump Pump 17 The Power of Flowmax Technology 18 17A Flowmax Pump 19 34A Flowmax Pump F Flowmax Pump 21 Packaged Airmix Systems Airmix Accessories Table of Contents

4 4World class finishing World Class Finishing Imagine a spray painting system that eliminates excess overspray, turbulence, and bounceback. A system that applies material to your parts, not your spray booth. Kremlin s Airmix technology substantially reduces coating usage, booth maintenance, and product rejects. Airmix is made for industrial users who require a world class finish and demand high application transfer efficiency. Airmix is a registered trademark of Kremlin. Airmix With the precision engineered Kremlin tip and aircap, atomization air is blended with the fluid at the locus of atomization, which delivers a very controlled balanced spray that produces a uniform build. Air-Assisted Airless With competitive tips and aircaps, air is injected directly into or beyond the locus of atomization. This creates excessive turbulence, overspray, coarse particles, and a very uneven film build requiring additional finishing steps. Xtra Series Fine Finish Tips These tips are specially designed to improve atomization of polyurethanes, water-based, & high solid coatings. The Xtra tips have been tested and proven at many customer locations & received great results. On standard coatings, these tips may also help to further reduce the amount of atomizing air needed at the gun.

5 The Benefits Of AIRMIX Airmix has become a standard in the industry by providing better atomization, producing lower paint velocities, requiring much lower air consumption and offering extremely high transfer efficiencies. Airmix - Superior to conventional, low pressure, and airless spraying. Paint Velocity - Reduces booth maintenance The paint velocity has a direct impact on performance: the higher the velocity, the greater the amount of overspray and bounceback, which combine to quickly pollute the booth. As can be seen from the graph on the right, the particle speed with Airmix is much lower than with all other systems. Transfer Efficiency - Saves on paint costs Users of Airmix achieve the highest transfer efficiency available. Efficiencies on different types of manual spray equipment are: Air Consumption - Lower energy costs Airmix uses less air for atomization air than any other high quality spray system. Airmix works well with smaller air compressors, lower production air pressure and lower compressed air volumes. This generates major savings in compressed air cost and reduces air compressor maintenance. Fine Atomization - Excellent finish Airmix uses a specially designed aircap to provide a smooth and even finish every time. The aircap helps to evenly atomize the paint as it leaves the fluid tip. This even atomization allows the paint to be broken down into smaller particles which provides the best coat with minimal defects or orange peel. 5 The benefits of Airmix Controlled atomization and high quality finish Cleaner environment Lower solvent emissions Higher application efficiency for fast production Enthusiastic operator acceptance Transfer efficiency eliminates waste and needless finishing steps Quick payback period ADVANTAGES OF AIRMIX Outstanding reliability Easy maintenance Material savings of up to 35% and more Up to 50% savings in spray booth waste Conforms to virutally all regulations Fast color changes PLUS: New MVX Gun offers unparalleled pattern control

6 Airmix MVX Features 6Airmix MVX features New adjustable VX14 K HVLP air cap Less force required to pull the trigger Stainless steel fluid passage and tip Trigger lock installed for safety Built-in fluid filter Only 3/4 of a turn to adjust the fan width New Trigger; Longer seat life Ergonomic design for a comfortable fit and feel Featherweight; 20.3 oz. / 575 g fully equipped Kremlin, the pioneer of the revolutionary Airmix technology, introduces its next generation Airmix gun, which eliminates more than 80% of overspray, reduces coating consumption by up to 50% and offers superior finish quality. Airmix is a HVLP (High Volume Low Pressure) compliant technology. Developed in partnership with our customers, this new Airmix gun offers many new benefits. In addition to the advantages of the adjustable fan, Kremlin has also improved the ergonomics by making the gun lighter, reducing trigger pull and redesigning the handle. A A A A The MVX features an adjustable fan to deliver the same powerful and unsurpassed atomization quality to all shapes and sizes.

7 MVX & MVXtra Guns This is the newest addition to the family of Airmix guns. It has superior ergonomic design and uses the highest quality components for long lasting reliable performance. Most importantly, it opens a whole new world to users by putting in the hands of an Airmix sprayer the ability to significantly vary the pattern without changing the tip while using minimal atomization air and pressure. FEATURE Lightweight ergonomic design with easy trigger pull Unparalleled pattern control at low atomization pressures All wetted parts are made of stainless steel Unique fluid tip and aircap design Benefit Reduces operator fatigue and increases productivity Maximum flexibility allows pattern width to be controlled similar to that of a conventional airspray gun while delivering efficiencies and increased production Sprays virtually all coatings including acid catalyzed topcoats, waterborne materials and 2K systems High quality finish and fewer rejects SPECIFICATIONS Sprayed materials Virtually all coatings Gun body material Forged Aluminum Maximum inlet air pressure 87 psi (6 bar) HVLP Compliant inlet air pressure (1) psi (0.87 bar) Air consumption psi (7.5 2 bar) Weight 20.3 oz (575 g) Maximum fluid temperature 122 F (50 C) Transfer efficiency (EN ) VX14 K HVLP : 81 % (±1%) Filter media size #6-85 mesh (168µ) Fluid output Depends on tip (see chart on page 10) Wetted parts, Carbide, Delrin and PTFE (1) NOTE: For HVLP compliance, the maximum inlet air pressure at the gun handle must not exceed psi(0.87 bar) to maintain 10 psi or less at the air cap. Testing for HVLP compliance was performed using the specified HVLP test air cap, the fan control fully closed and a pressure gauge on the air inlet fitting at the gun base or handle. It may also be a requirement of some regulatory agencies that users have the appropriate test air cap available on site to verify that the gun is being operated within the regulatory limitations. FITTINGS Fitting Air Inlet M 1/4" NPS Fluid Inlet M #5 JIC MVX PART NUMBER WITH VX14 K HVLP aircap Max. Fluid Pressure Gun Model Seat Insert Bare Gun Only Gun Assembly Air cap Tip Size psi bar Material Part Number Part Number MVX Delrin MVX VX14 K HVLP Standard MVX Carbide MVXtra Delrin VX14 K HVLP Xtra MVXtra HVLP Compliance testing components Description Part Number VX14 K HVLP Test aircap with gauges Inlet pressure test gauge assembly Airmix MVX & MVXtra guns maintenance kits Description Part Number Seal kit Repair kit

8 MXLT Gun 8Airmix MXLT gun The MXLT has a history of proven performance in thousands of locations throughout the world and is what all other designs are compared to. It is a reliable, heavy-duty spray gun that has built the Airmix tradition of outstanding finish quality at unsurpassed transfer efficiencies. FEATURE Unique fluid tip and aircap design All wetted parts are made of stainless steel Special low pivot trigger for easy trigger pull Drop-forged aluminum body and nickelplated brass components SPECIFICATIONS Sprayed materials Virtually all coatings Gun body material Forged Aluminum Maximum inlet air pressure 87 psi (6 bar) HVLP Compliant inlet air pressure (1) 15.5 psi (1.07 bar) Air consumption psi (5 2 bar) Weight 23.5 oz (665 g) Maximum fluid temperature 122 F (50 C) Transfer efficiency (EN ) BX16 K HVLP : 78 % (±1%) Filter media size #6-85 mesh (168µ) Fluid output Depends on tip (see chart on page 10) Wetted parts, Carbide, Delrin and PTFE (1) NOTE: For HVLP compliance, the maximum inlet air pressure at the gun handle must not exceed 15.5 psi (1.07 bar) to maintain 10 psi or less at the air cap. Testing for HVLP compliance was performed using the specified HVLP test air cap, the fan control fully open and a pressure gauge on the air inlet fitting at the gun base or handle. It may also be a requirement of some regulatory agencies that users have the appropriate test air cap available on site to verify that the gun is being operated within the regulatory limitations. FITTINGS Benefit High quality finish and fewer rejects Sprays virtually all coatings including acid catalyzed topcoats, waterborne materials and 2K systems Reduces operator fatigue and increases productivity Extreme reliability and limited maintenance Fitting Air Inlet M 1/4" NPS Fluid Inlet M #5 JIC M22HTIG - HVLP PART NUMBERs WITH E5 K HVLP aircap Max. Fluid Pressure Gun Model Seat Insert Material Air cap psi bar Tip Size Bare Gun Only Part Number Gun Assembly Part Number MXLT * 200 BX16 K HVLP Standard * Gun comes standard as 1740 psi (120 bar) configuration psi (90 bar) and 2900 psi (200 bar) configurations can be created by exchanging components supplied in the conversion kit that comes with the gun. HVLP Compliance testing components Description Part Number BX16 K HVLP Test aircap with gauges Inlet pressure test gauge assembly maintenance kits Description Part Number Seal kit Repair kit

9 Airmix Aircaps Aircaps for mvx & MVXTRA guns VX14 K HVLP VX54 VX114 K HVLP Airmix Aircaps & Tips 9 Part Number Adjustable fan Yes No No Non-stick coating No Yes No Atomization quality Excellent Excellent Excellent Aircaps for MXLT Gun BX16 K HVLP BX36 BX56 BX86 BX116 K HVLP Part Number Adjustable fan No No No No No Non-stick coating No No Yes No No Atomization quality Excellent Very good Good Very good Excellent Airmix Fluid Tips Tip Number 500 psi 35 bar Fluid Output 1000 psi 70 bar oz/min cm³/min oz/min cm³/min Ø in Inches Ø in mm Gun Filter Mesh Filter # Pump Filter Mesh Filter # Spray Angle and Maximum Fan Width at 10 (25cm) cm 13 cm 18 cm 23 cm 24 cm 25 cm 31 cm 33 cm 38 cm 46 cm 60 cm (2) (4) (4) (6) 85 (6) (8) (12) (12) = Standard tips - To order a tip, replace the crosses in 134-5xx-xx4 with the corresponding number from the chart above. (Example: for a tip) When ordering a 100 tip, use 134-xxx-xx4 (Example: ). = Xtra tips - To order a tip, replace the crosses in 134-5xx-xx2 with the corresponding number from the side chart. (Example: for a tip) = Special Order tips - These tips require a minimum of 25 tips per order and these tips cannot be ordered in the Xtra tip style. = Optimum Fan Adjustment - These tips allow for fan adjustment when used with a VX14 air cap. Airmix Xtra Fluid Tips Airmix aircaps & tips

10 Airmix Booth Pump Selector 10 Intensive & Flowmax pumps Pump Model Construction Intensive Intensive Intensive Intensive Intensive Intensive Intensive 17A Flowmax 34A 20.25F Flowmax Flowmax l l l l l l l l l l Mounting Bare Wall-mounted l l l l l l l l l l Cart-mounted Dimensions (wall-mounted pump without filter and siphon hose) Height Width Depth Weight (Wall-mounted) Air motor / Fluid section Inches mm Inches mm Inches mm lbs kg Air Motor Stroke Inches mm Fluid Section S 30S 25F Specifications Pressure ratio 10:1 20:1 40:1 17:1 34:1 20:1 Output per cycle Number of cycles per Output at 30 cycles/minute Free flow per minute Maximum fluid pressure Maximum fluid temperature Working air pressure oz cc gallon liter gallon liter gallon liter psi bar F 122 C 50 psi 14.5 to 87 bar 1 to 6 Maximum air scfm consumption (1) Nm³/h Fittings Air inlet (valve) F3/8 BSP F3/4 BSP Fluid inlet M18 x 125 M26 x 125 Fluid outlet M1/2 (#5) JIC F3/8 BSP F3/4 BSP F3/8 BSP - Not Available l Standard Optional - with purchase of additional (1) Air consumption is measured at 30 cycles with a pump inlet pressure of 87 psi (6 bar).

11 Easy-to-Work-With Pump Selector In 80% of the cases a pump can be selected based on the number of guns and the atomization energy required to deliver acceptable finish quality. We ve created the following two tables for selecting pumps that would normally be installed near the paint booth. 11 # of Guns # of Guns DEAD END SYSTEM (Covers 80% of cases - See below for conditions) Fluid Pressure psi (20-55 bar) psi ( bar) psi ( bar) 1 EZMix or or 17A Flowmax or 17A Flowmax Applicable conditions for above tables: 1-32 ft. / 10 m or less fluid hose with inside diameter of 3/16" / 5 mm 2 - Maximum tip size orifice per gun is.019" /.5mm 3 - Circulation loop up to 50 ft. / 15 m including return 4-8 hours per day of production 5 - Coating viscosity does not exceed 30 seconds in a ZAHN #2 or 32 seconds in a CA4 viscosity cup For other conditions, contact your authorized Kremlin distributor or 34A Flowmax 3 See Circulation Pump Catalog or Flowmax or more See Circulation Pump Catalog HEATED OR NON-HEATED CIRCULATING SYSTEM (Covers 80% of cases - See below for conditions) Fluid Pressure psi (20-55 bar) psi ( bar) psi ( bar) or 17A Flowmax or Flowmax or 34A Flowmax 2 See Circulation Pump Catalog or 17A Flowmax or more See Circulation Pump Catalog Flowmax or Standard Pump? The best selection is always Flowmax except for applications that require frequent color changes or where the coating has a pot life of less than 24 hours. Easy-to-work-with pump selector

12 EZMix Piston Pump 12 EZMix piston pump Pump Air Consumption scfm (Nm³/hr) 2.0 (3.4) (2.6) (1.7) (0.9) (0.8) 14.5 (1) 0.7 (1.1) 29.0 (2) 0.9 (1.5) 43.5 (3) 1.1 (1.9) 58.0 (4) 1.4 (2.3) 72.5 (5) 1.6 (2.7) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute. This is our new entry level Airmix pump. It uses the same high efficiency and environmentally friendly technology that is found on the pump. This pump is ideal for small to hobbyist shops that can benefit from the power of Airmix FEATURE Small fluid section and suction rod Gun and pump package runs on a 1.5 HP compressor Simple design with minimal parts Compact design SPECIFICATIONS Compression ratio 10:1 Fluid volume per cycle 0.6 oz (18 cc) Number of cycles per gallon 210 Maximum Air consumption at 30 cycles/min psi (2.7 6 bar) Fluid output at 30 cycles 0.14 gallon (0.53 liter) Free flow rate 0.29 gallon/min (1.1 liter/minute) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 870 psi (60 bar) Maximum fluid temperature 140 F (60 C) Sound level 80 dba Upper seal cartridge with GT seal Lower seal PFA seals Pump construction Wetted parts Weight - wall-mounted pump 11.7 lbs. (5.3 kg) Height - wall-mounted pump 16.0 (405 mm) Width - wall-mounted pump 12.0 (305 mm) Depth - wall-mounted pump 7.0 (178 mm) FITTINGS Benefit Minimizes waste during clean-up and allows for fast color changes Low compressed air consumption equals lower energy costs Allows for easy field repair at a low cost Fits almost anywhere and easily transports to on-site projects Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) 5/16" F Pushlock Tube Fluid inlet M 18 x 125 Fluid outlet M #5 JIC EZMix Pump part numbers Set-up Pump air regulator Suction rod Filter Part number Wall-mounted l maintenance kits Description Part number Air motor - maintenance kit for model 340/ Fluid section - seal kit for model H Fluid section - maintenance kit for model H

13 10.14 Intensive Pump The is our most popular pump and is recognized for its reliability as a workhorse in the finishing industry. The is used in a wide variety of manufacturing environments including wood, metal, and plastic. FEATURE Small fluid section and suction rod Gun and pump package runs on a 1.5 HP compressor Simple design with minimal parts Compact design Benefit Minimizes waste during clean-up and allows for fast color changes Low compressed air consumption equals lower energy costs Allows for easy field repair at a low cost Fits almost anywhere and easily transports to on-site projects SPECIFICATIONS Compression ratio 10:1 Fluid volume per cycle 0.6 oz (18 cc) Number of cycles per gallon 213 Maximum Air consumption at 30 cycles/min psi (2.7 6 bar) Fluid output at 30 cycles 0.14 gallon (0.53 liter) Free flow rate 0.29 gallon/min (1.1 liter/minute) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 870 psi (60 bar) Maximum fluid temperature 140 F (60 C) Sound level 80 dba Upper seal cartridge with GT seal Lower seal Perfluoroalkoxy Fluorocarbon cup seal Pump construction Wetted parts Weight - wall-mounted pump 12 lbs. (5.5 kg) Height - wall-mounted pump 16.0 (405 mm) Width - wall-mounted pump 12.0 (305 mm) Depth - wall-mounted pump 7.0 (178 mm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid inlet M 18 x 125 Fluid outlet M #5 JIC Intensive Pump part numbers Set-up Pump and Gun regulators Suction rod Filter Part number Wall-mounted l 5 Gallon Wall-mounted l 55 Gallon Pump Air Consumption scfm (Nm³/hr) 2.0 (3.4) (2.6) (1.7) (0.9) (0.8) 14.5 (1) 0.7 (1.1) 29.0 (2) 0.9 (1.5) 43.5 (3) 1.1 (1.9) 58.0 (4) 1.4 (2.3) 72.5 (5) 1.6 (2.7) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute Intensive pump maintenance kits Description Part number Air motor - maintenance kit for model 340/ Fluid section - seal kit for model H Fluid section - maintenance kit for model H

14 10.25 Intensive Pump 14 The is the ideal pump for medium to large production shops applying low viscosity coatings with one or two guns. This pump is designed to cycle at low pressure to maximize operation and efficiency Intensive pump Pump Air Consumption scfm (Nm³/hr) 5.0 (8.5) (6.8) (5.1) (3.4) (1.7) (2.2) 14.5 (1) 1.9 (3.2) 2.5 (4.3) 3.2 (5.4) 3.8 (6.5) 29.0 (2) 43.5 (3) 58.0 (4) 72.5 (5) Pump Air Inlet Pressure psi (bar) 4.5 (7.6) 87.0 (6) FEATURE Large suction rod assembly and higher pressure ratio Operates at low pressures Minimal parts SuperQuiet air motor SPECIFICATIONS Compression ratio 10:1 Fluid volume per cycle 1.7 oz (50 cc) Number of cycles per gallon 75.3 Maximum Air consumption at 30 cycles/min psi (7.6 6 bar) Fluid output at 30 cycles 0.4 gallon (1.5 liter) Free flow rate 0.8 gallon/min (3.0 liter/minute) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 870 psi (60 bar) Maximum fluid temperature 140 F (60 C) Sound level 78 dba Upper seal GT seal Lower seal Polyethelene GT seal Pump construction Wetted parts Weight - wall-mounted pump 37.5 lbs. (17 kg) Height - wall-mounted pump (820 mm) Width - wall-mounted pump (350 mm) Depth - wall-mounted pump 8.25 (210 mm) FITTINGS Benefit Able to siphon and atomize thicker coatings in an ergonomic package Great for stains and other thin coatings requiring minimal atomization energy Easy and quick to field repair Ideal for booth-mounted location for quiet sprayer environment Fitting Air inlet (valve) F 3/8" BSP Air outlet (atomization air) M 1/4" NPS Fluid inlet M 26 x 125 Fluid outlet M #5 JIC Intensive Pump part numbers Set-up Pump and gun regulators Suction rod Filter Part number Wall-mounted l 5 Gallon Wall-mounted l 5 Gallon l Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute. maintenance kits Description Part number Air motor - seal kit for model Air motor - maintenance kit for model Fluid section - seal kit for model H Fluid section - maintenance kit for model H

15 20.15 Intensive Pump A multi-purpose, very quiet pump designed to deliver thicker coatings (up to 9000 CPS) to a single spray gun in either wood, metal, or plastic finishing applications. 15 FEATURE Large suction rod assembly and higher pressure ratio Gun/pump package runs on a 2 HP compressor Minimal parts Compact design Benefit Able to siphon and atomize thicker coatings in an ergonomic package Low compressed air consumption equals low energy costs Easy and quick to field repair Fits almost anywhere and easily transports to on-site projects SPECIFICATIONS Compression ratio 20:1 Fluid volume per cycle 0.7 oz (22 cc) Number of cycles per gallon 183 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.71 gallon (0.66 liters) Free flow rate 0.34 gallon/min (1.32 liter/minute) Minimum air inlet pressure 14.5 psi (1 bar) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 1740 psi (120 bar) Maximum fluid temperature 122 F (50 C) Sound level 80 dba Upper seal GT cartridge Lower seal Perfluoroalkoxy Fluorocarbon cup seal Pump construction Wetted parts & PFA Weight - wall-mounted pump 19.9 lbs. (9 kg) Height - wall-mounted pump 17 (430 mm) Width - wall-mounted pump 9.5 (240 mm) Depth - wall-mounted pump (270 mm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC Intensive Pump part numbers Set-up Pump and gun regulators Suction rod Filter Part number Wall-mounted l Wall-mounted l 5 Gallon Pump Air Consumption scfm (Nm³/hr) 4.0 (6.8) (6.0) (5.1) (4.3) (3.4) (2.6) (1.7) (0.9) (1.9) 14.5 (1) 1.7 (2.9) 29.0 (2) 2.2 (3.8) 43.5 (3) 2.8 (4.8) 58.0 (4) 3.4 (5.7) 72.5 (5) 3.9 (6.7) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute Intensive pump maintenance kits Description Part number Air motor - maintenance kit for model Fluid section - seal kit for model H Fluid section - maintenance kit for model H

16 20.25 Intensive Pump Intensive pump Pump Air Consumption scfm (Nm³/hr) 10.0 (17.0) (13.6) (10.2) (6.8) (3.4) (4.3) 14.5 (1) 3.8 (6.5) 29.0 (2) 5.1 (8.6) 43.5 (3) 8.9 (15.1) 7.6 (13.0) 6.4 (10.8) 58.0 (4) 72.5 (5) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute. Ideal for feeding one or two Airmix spray guns in a small to medium production shop, the can pump a wide variety of coatings. The pump is available with pump regulator, atomization regulator, and fluid filter. FEATURE Large suction rod assembly and higher pressure ratio Minimal parts Wetted components and PTFEG Polyfluid packings SuperQuiet air motor Benefit Able to siphon and atomize thicker coatings in an ergonomic package Easy and quick to field repair Compatible with most coatings and limited maintenance Ideal for booth-mounted location for quiet sprayer environment SPECIFICATIONS Compression ratio 20:1 Fluid volume per cycle 1.7 oz (50 cc) Number of cycles per gallon 75.3 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.4 gallon (1.5 liter) Free flow rate 0.8 gallon/min (3.0 liter/minute) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 1740 psi (120 bar) Maximum fluid temperature 140 F (60 C) Sound level 78 dba Upper seal Polyfluid / PTFEG Seal Lower seal Polyethelene GT seal Pump construction Wetted parts Weight - wall-mounted pump 48.5 lbs. (22 kg) Height - wall-mounted pump (820 mm) Width - wall-mounted pump (350 mm) Depth - wall-mounted pump 8.25 (210 mm) Depth - wall-mounted pump 10.2 (26 mm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC Intensive Pump part numbers Set-up Pump air regulator Suction rod Filter Part number Wall-mounted l 5 Gallon Wall-mounted l 5 Gallon l Wall-mounted l 55 Gallon l maintenance kits Description Part number Air motor - seal kit for model Air motor - maintenance kit for model Fluid section - seal kit for model H Fluid section - maintenance kit for model H

17 20.50 Intensive Pump The pump is ideal for large production shops where medium to heavy bodied materials will be fed to multiple guns from one fluid supply. 17 FEATURE Large suction rod assembly and higher pressure ratio Extra thick hard chrome over stainless Minimal parts SuperQuiet air motor Benefit Able to siphon and atomize thicker coatings in an ergonomic package Long lasting piston and cylinder Easy and quick to field repair Ideal for booth-mounted location for quiet sprayer environment SPECIFICATIONS Compression ratio 20:1 Fluid volume per cycle 3.4 oz (100 cc) Number of cycles per gallon 38 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.8 gallon (3 liters) Free flow rate 1.6 gallon/min (15 liter/minute) Minimum air inlet pressure 14.5 psi (1 bar) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 1740 psi (120 bar) Maximum fluid temperature 122 F (50 C) Sound level 78 dba Upper seal Polyfluid / PTFEG Seal Lower seal Polyethelene GT seal Pump construction Wetted parts Weight - wall-mounted pump 66.2 lbs. (30 kg) Height - wall-mounted pump 33 (840 mm) Width - wall-mounted pump 18.5 (470 mm) Depth - wall-mounted pump (270 mm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC Intensive Pump part numbers Set-up Pump air regulator Suction rod Filter Part number Wall-mounted l 5 Gallon Wall-mounted l 5 Gallon l Wall-mounted l 55 Gallon l Pump Air Consumption scfm (Nm³/hr) 20.0 (34.0) (25.5) (17.0) (8.5) (8.6) 14.5 (1) 7.6 (13.0) 29.0 (2) 10.2 (17.3) 43.5 (3) 12.7 (21.6) 58.0 (4) 15.3 (25.9) 72.5 (5) 17.8 (30.2) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute Intensive pump maintenance kits Description Part number Air motor - seal kit for model Air motor - maintenance kit for model Fluid section - seal kit for model H Fluid section - maintenance kit for model H

18 40.25 Intensive Pump Intensive pump Pump Air Consumption scfm (Nm³/hr) 20.0 (34.0) (25.5) (17.0) (8.5) (8.6) 14.5 (1) 7.6 (13.0) 29.0 (2) 10.2 (17.3) 43.5 (3) 12.7 (21.6) 58.0 (4) 15.3 (25.9) 72.5 (5) 17.8 (30.2) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute. The pump is ideal for medium to large production shops with medium to heavy viscosity materials using high pressure Airmix. The Super Quiet air motor and high quality components keep this pump operating at maximum efficiency. FEATURE Large suction rod assembly and higher pressure ratio Minimal parts SuperQuiet air motor SPECIFICATIONS Compression ratio 40:1 Fluid volume per cycle 1.7 oz (50 cc) Number of cycles per gallon 76 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.4 gallon (1.5 liters) Free flow rate 0.8 gallon/min (3.0 liter/minute) Minimum air inlet pressure 14.5 psi (1 bar) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 3480 psi (240 bar) Maximum fluid temperature 122 F (50 C) Sound level 78 dba Upper seal Polyfluid / PTFEG Seal Lower seal Polyethelene GT seal Pump construction Wetted parts Weight - wall-mounted pump 61.7 lbs. (28 kg) Height - wall-mounted pump 31.5 (800 mm) Width - wall-mounted pump (400 mm) Depth - wall-mounted pump 11 (280 mm) FITTINGS Intensive Pump part numbers Benefit Able to siphon and atomize thicker coatings in an ergonomic package Easy and quick to field repair Ideal for booth-mounted location for quiet sprayer environment Fitting Air inlet (valve) F 3/4" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC Set-up Pump air regulator Suction rod Filter Part number Wall-mounted l 5 Gallon Wall-mounted l 5 Gallon l Wall-mounted l 55 Gallon l maintenance kits Description Part number Air motor - seal kit for model Air motor - maintenance kit for model Fluid section - seal kit for model H Fluid section - maintenance kit for model H

19 40.50 Intensive Pump The is the pump for extreme industrial users and applications. Large ports and high air to fluid ratio allows for high atomization at constant flow rates. Ideal for high pressure Airmix applications. FEATURE Large suction rod assembly and higher pressure ratio Extra thick hard chrome over stainless Minimal parts SuperQuiet air motor Benefit Able to siphon and atomize thicker coatings in an ergonomic package Long lasting piston and cylinder Easy and quick to field repair Ideal for booth-mounted location for quiet sprayer environment SPECIFICATIONS Compression ratio 40:1 Fluid volume per cycle 3.4 oz (100 cc) Number of cycles per gallon 38 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.8 gallons (3.0 liters) Free flow rate 1.6 gallon/min (6.0 liter/minute) Minimum air inlet pressure 14.5 psi (1 bar) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 3480 psi (240 bar) Maximum fluid temperature 122 F (50 C) Sound level 78 dba Upper seal Polyfluid / PTFEG Seal Lower seal Polyethelene GT seal Pump construction Wetted parts Weight - wall-mounted pump 66.2 lbs. (30 kg) Height - wall-mounted pump 31.5 (800 mm) Width - wall-mounted pump (400 mm) Depth - wall-mounted pump 11 (280 mm) FITTINGS Fitting Air inlet (valve) F 3/4" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC Pump part numbers Set-up Pump air regulator Suction rod Filter Part number Wall-mounted l 5 Gallon Wall-mounted l 5 Gallon l Pump Air Consumption scfm (Nm³/hr) 40.0 (68.0) (59.5) (51.0) (42.5) (34.0) (25.5) (17.0) (8.5) (17.3) 14.5 (1) 15.3 (25.9) 29.0 (2) 20.3 (34.6) 43.5 (3) 25.4 (43.2) 58.0 (4) 30.5 (51.8) 72.5 (5) 35.6 (60.5) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute Intensive pump maintenance kits Description Part number Air motor - seal kit for model T Air motor - maintenance kit for model T Fluid section - seal kit for model H Fluid section - maintenance kit for model H

20 Flowmax Pump Features 20Flowmax pump features The exclusive Flowmax SuperLife Technology is available only with Kremlin. Nothing of similar pressure and fluid output in the piston pump design outperforms the Flowmax SuperLife technology. Flowmax pumps substantially outlast standard piston pumps using self-adjusting seals. There is no lubricant cup, thus eliminating leaking packings. A packing-free pump that performs quietly with minimal service. Nothing compares! How Does It Work? There are two reasons why Flowmax pumps outperform. 1. Exclusive precisely machined SuperLife bellows replace the traditional leaky packings. 2. Extra thick self-adjusting seal that is in a fixed position and spring loaded for longer life. C. A. B. Features and Benefits of the Flowmax Fluid Section FEATURE (A) Exclusive precisely machined SuperLife bellows replace the traditional leaky packings (B) The fluid inlet is located at the upper area of the fluid section (C) Single lip seals with automatic wear take-up device Benefit No constant packing adjustment No risk of running without lubricant and destroying the pump Easier to service the pump High up-time minimizes maintenance Do s and Don ts for Flowmax Pumps Do Install in a circulation system Install in a non-circulating system Use with moisture-sensitive coatings such as polyurethane catalyst Use with slightly abrasive coatings don t Pressure feed the pumps Install check valves on the suction assembly Install in locations that require frequent color changes Use with 2K coatings with a pot life under 4 hours

21 17A Flowmax Pump Our most popular Flowmax pump with thousands of satisfied customers worldwide. Due to its low friction Flowmax design, this pump can be used in both the low and medium Airmix pressure range. FEATURE Special engineered carbide seats Low friction self-adjusting seals Floating piston self centers to align with packings Benefit Ideal for highly abrasive coatings, extends time between rebuilds and reduces maintenance costs Maintains constant seal between packings and piston rod to provide consistant and reliable operation Provides longer life with minimal wear SPECIFICATIONS Compression ratio 17:1 Fluid volume per cycle 2.0 oz (60 cc) Number of cycles per gallon 64 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.48 gallons (1.8 liters) Free flow rate 0.96 gallon/min (3.6 liter/minute) Minimum air inlet pressure 14.5 psi (1 bar) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 1479 psi (102 bar) Maximum fluid temperature 122 F (50 C) Sound level 78 dba Upper seal Polyethylene GT seal Lower seal Polyethylene GT seal Pump construction Wetted parts and Carbide Weight - wall-mounted pump (20 kg) Height - wall-mounted pump 24.5 (622 mm) Width - wall-mounted pump 13 (330 mm) Depth - wall-mounted pump 8.25 (211 mm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC 17A Flowmax Pump part numbers Set-up Pump and gun regulators Suction rod Filter Part number Wall-mounted l Wall-mounted l - l Wall-mounted l 5 Gallon l Wall-mounted l 55 Gallon l Pump Air Consumption scfm (Nm³/hr) 10.0 (17.0) (13.6) (10.2) (6.8) (3.4) (4.4) 14.5 (1) 3.9 (6.6) 29.0 (2) 5.2 (8.8) 43.5 (3) 6.5 (11.0) 58.0 (4) 7.8 (13.2) 72.5 (5) 9.1 (15.4) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute A Flowmax pump maintenance kits Description Part number Air motor - seal kit for model Air motor - maintenance kit for model Fluid section - seal kit for model 30S Fluid section - maintenance kit for model 30S

22 34A Flowmax Pump 22 34A Flowmax pump Pump Air Consumption scfm (Nm³/hr) 20.0 (34.0) (25.5) (17.0) (8.5) (8.8) 14.5 (1) 7.8 (13.2) 29.0 (2) 10.4 (17.6) 43.5 (3) 13.0 (22.0) 58.0 (4) 15.6 (26.4) 72.5 (5) 18.2 (30.8) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute. The Flowmax 34A pump uses the same fluid section as the 17A but with twice the fluid pressure power. This pump is ideal for high pressure Airmix applications. FEATURE Special engineered carbide seats Low friction self-adjusting seals Floating piston self centers to align with packings SPECIFICATIONS Compression ratio 34:1 Fluid volume per cycle 2.0 oz (60 cc) Number of cycles per gallon 64 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.48 gallons (1.8 liters) Free flow rate 0.96 gallon/min (3.6 liter/minute) Minimum air inlet pressure 14.5 psi (1 bar) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 2958 psi (204 bar) Maximum fluid temperature 122 F (50 C) Sound level 78 dba Upper seal Polyethylene GT seal Lower seal Polyethylene GT seal Pump construction Wetted parts and Carbide Weight - wall-mounted pump 59.5 (27 kg) Height - wall-mounted pump 24 (610 mm) Width - wall-mounted pump (410 mm) Depth - wall-mounted pump 10 (250 mm) FITTINGS 34A Flowmax Pump part numbers Benefit Ideal for highly abrasive coatings, extends time between rebuilds and reduces maintenance costs Maintains constant seal between packings and piston rod to provide consistant and reliable operation Provides longer life with minimal wear Fitting Air inlet (valve) F 3/4" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC Set-up Pump air regulator Suction rod Filter Part number Wall-mounted l 5 Gallon l Wall-mounted l 55 Gallon l maintenance kits Description Part number Air motor - seal kit for model Air motor - maintenance kit for model Fluid section - seal kit for model 30S Fluid section - maintenance kit for model 30S

23 20.25F Flowmax Pump The 20.25F Flowmax pump is ideal for the pumping of medium to heavy bodied coatings as well as corrosive or abrasive materials in small circulating or 1 to 2 gun systems. 23 FEATURE Special engineered carbide seats Low friction self-adjusting seals Floating piston self centers to align with packings Benefit Ideal for highly abrasive coatings, extends time between rebuilds and reduces maintenance costs Maintains constant seal between packings and piston rod to provide consistant and reliable operation Provides longer life with minimal wear SPECIFICATIONS Compression ratio 20:1 Fluid volume per cycle 1.7 oz (50 cc) Number of cycles per gallon 75.3 Maximum Air consumption at 30 cycles/min psi ( bar) Fluid output at 30 cycles 0.4 gallon (1.5 liter) Free flow rate 0.8 gallon/min (3.0 liter/minute) Maximum air inlet pressure 87 psi (6 bar) Maximum fluid pressure 1740 psi (120 bar) Maximum fluid temperature 140 F (60 C) Sound level 78 dba Upper seal Polyethelene GT seal Lower seal Polyethelene GT seal Pump construction Wetted parts Weight - wall-mounted pump 66.2 lbs. (30 kg) Height - wall-mounted pump (970 mm) Width - wall-mounted pump (350 mm) Depth - wall-mounted pump 8.25 (210 mm) Depth - wall-mounted pump 10.2 (26 mm) FITTINGS Fitting Air inlet (valve) F 3/8" BSP Fluid inlet M 26 x 125 Fluid outlet M #5 JIC 20.25F Flowmax Pump part numbers Set-up Pump air regulator Suction rod Filter Part number Wall-mounted l 5 Gallon Wall-mounted l 5 Gallon l Wall-mounted l 55 Gallon l Pump Air Consumption scfm (Nm³/hr) 10.0 (17.0) (13.6) (10.2) (6.8) (3.4) (4.3) 14.5 (1) 3.8 (6.5) 29.0 (2) 5.1 (8.6) 43.5 (3) 6.4 (10.8) 58.0 (4) 7.6 (13.0) 72.5 (5) 8.9 (15.1) 87.0 (6) Pump Air Inlet Pressure psi (bar) Note: All scfm consumptions shown in the above graph are for the pump operating at 30 cycles per minute F Flowmax pump maintenance kits Description Part number Air motor - seal kit for model Air motor - maintenance kit for model Fluid section - seal kit for model 25F Fluid section - maintenance kit for model 25F

24 Packaged Airmix Systems 24Packaged Airmix systems EZMix Stand Cart (2) Arm Cart Cart (2) Arm Cart EZMix Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Agitator Gun Model Part Number Floor Stand Gallon Tube 16ft (4.9m) No MVX Wall Gallon Tube 16ft (4.9m) No MVX Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Agitator Gun Model Part Number Portable 2 5 Gallon 25ft (7.5m) No MVX Wall 2 5 Gallon 25ft (7.5m) No MVX Arm Cart 2 5 Gallon 25ft (7.5m) No MVX Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Wall 2 5 Gallon 25ft (7.5m) Yes Yes* MVX Arm Cart 2 5 Gallon 25ft (7.5m) Yes No MVX Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Agitator Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) No MVX Wall 2 55 Gallon 25ft (7.5m) No MVX Portable 2 5 Gallon 25ft (7.5m) No MVX Arm Cart 2 5 Gallon 25ft (7.5m) No MVX Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Wall 2 5 Gallon 25ft (7.5m) Yes Yes* MVX Arm Cart 2 5 Gallon 25ft (7.5m) Yes No MVX * Systems marked Yes come equipped with 110v explosion proof heater (part # ) and a stainless steel circulating kit (part # ).

25 Packaged Airmix Systems Cart 17A Wall 34A Cart 20.25F Cart Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Wall 2 5 Gallon 25ft (7.5m) Yes Yes* MVX Wall 2 55 Gallon 25ft (7.5m) Yes Yes* MVX Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Arm Cart 2 5 Gallon 25ft (7.5m) Yes No MVX Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Arm Cart 2 5 Gallon 25ft (7.5m) Yes No MVX A Flowmax Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Wall 2 5 Gallon 25ft (7.5m) Yes Yes* MVX Arm Cart 2 5 Gallon 25ft (7.5m) Yes No MVX A Flowmax Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Arm Cart 2 5 Gallon 25ft (7.5m) Yes No MVX F Flowmax Pump Packaged Systems Mounting Arrangement Number of Regulators Suction Rod Size Length of Hoses Filter Heater w/ Circulation Kit Gun Model Part Number Wall 2 5 Gallon 25ft (7.5m) Yes No MVX Wall 2 55 Gallon 25ft (7.5m) Yes No MVX Wall 2 5 Gallon 25ft (7.5m) Yes Yes* MVX Arm Cart 2 5 Gallon 25ft (7.5m) Yes No MVX * Systems marked Yes come equipped with 110v explosion proof heater (part # ) and a stainless steel circulating kit (part # ). Packaged Airmix systems

26 Airmix Accessories 26 Airmix Accessories 1. swivel Extensions for airmix spray guns Item Description MXLT Part Number MVX Part Number A. 90º Angle elbow extension - 7" (178 mm) B. 90º Angle elbow extension - 10" (254 mm) C. 90º Angle elbow extension - 16" (406 mm) D. 90º Angle elbow extension - 22" (559 mm) E. 90º Angle elbow extension - 28" (711 mm) TWO GUN MANIFOLD (STAINLESS STEEL) A. Two gun manifold for Airmix guns Manual gun covers A. Protective gun covers - Pack of protective hose sleeve A. Hose sleeve - 16ft. / 5m B. Hose sleeve - 25ft. / 7.5m C. Hose sleeve - 32ft. / 10m D. Hose sleeve - 50ft. / 15m E. Hose sleeve - 100ft. / 30m F. Hose sleeve ft. / 300m Test aircaps with gauge(s) for hvlp compliance testing A. VX14 K HVLP test aircap with gauges for MVX gun B. VX114 K HVLP test aircap with gauge for MVX gun C. BX16 K HVLP test aircap with gauges for MXLT gun D. BX116 K HVLP test aircap with gauges for MXLT gun Gun handle inlet pressure gauge for hvlp compliance testing A psi gauge assembly for testing gun inlet pressure (M/F 1/4 NPS)

27 Airmix Accessories A. A. A. B. 6. seat inserts for airmix guns Item Description MXLT Part Number MVX Part Number A. Delrin (Pack of 10) B. (Pack of 2) C. Carbide (Pack of 2) D. S/S and Carbide seat insert seals (Pack of 10) microscreens and tip seals for airmix guns A. Microscreens for tip sizes 02, 03, 04, & 06 (140 Mesh) B. Tip seals for tip sizes 09 and larger screens for inline gun filter A. Screen #4 - For tip sizes 02, 03, 04, & 06 (Pack of 5) Mesh size (100 microns) B. Screen #6 - For tip size 09 (Pack of 5) Mesh size - 85 (1168 microns) C. Screen #12 - For tip sizes 12 and larger (Pack of 5) Mesh size - 60 (280 microns) Tip cleaning needles and needle holder A. Cleaning needles for tip sizes 09 and smaller (Pack of 12) B. Cleaning needles for tip sizes 12 and larger (Pack of 12) C. Unclogging needle holder techni-lub - ptfe grease A. (1) 0.33 oz Tube of Techni Lub B. (1) 15.5 oz Can of Techni Lub Airmix Accessories A. B. 11. viscosity cup & wet film thickness gauge A. Viscosity cup number 4 (CA4) B. Wet film build thickness test gauge

28 Airmix Accessories 28 A. C. 13. Pump carts A. Single post cart (Used for and pumps) B. Two arm cart w/ wall plate (Used for all other pumps) C. Four wheel cart with 5 gallon pail holder (Recommended for all pumps) D. Add-on tray to hold 1 gallon container for 4 wheel cart Airmix Accessories D. 14. paint heaters - stainless steel Operate at 1500 watts Fluid inlet and outlet are #5 JIC Temperature range from F (15-80 C) A. 110V AC Explosion-proof paint heater B. 220V AC Explosion-proof paint heater Circulating kits Each Circulating Kit Contains: (1) 3ft. / 0.9m Whip Hose, (1) 10ft. / 3m Fluid Hose For Heater, (1) 25ft. / 7.5 m Hose, Y fitting and back pressure regulator or valve kit A. Aluminum circulating kit B. valve circulating kit (Back pressure regulator is used in place of circulation valve) C. Airmix back pressure regulator AIRMIX FLUID PRESSURE REGULATORS A. Airmix fluid regulator, psi (10-70 bar) B. Airmix fluid regulator, psi ( bar) C. Airmix fluid regulator PH, psi ( bar) D. Airmix fluid regulator with gauge kit, psi (10-70 bar) E. Airmix fluid regulator with gauge kit, psi ( bar) F. Fluid filter and regulator kit with bracket, psi (10-70 bar) G. Fluid filter and regulator kit with bracket, psi ( bar) H. Airmix back pressure regulator, psi ( bar) I. S/S Circulation kit, c/w drain rod, fits inlet (for use with ) J. Fluid regulator bracket and screws A. D. 17. two & three way suction Inlet Manifolds Used to quickly switch the pump feed between two or three different containers while reducing the waste. Example: Switch from coating #1 to solvent for flushing and then to coating #2 A. Two-way suction manifold for inlet (siphon hoses not included) B. Two-way suction manifold for inlet (siphon hoses not included) C. Two-way S/S suction manifold for inlet (siphon hoses not included) D. Three-way suction manifold for inlet (siphon hoses not included) E. Three-way suction manifold for inlet (siphon hoses not included) F. Three-way S/S suction manifold for inlet (siphon hoses not included) Stainless steel suction hose & rod assemblies C. Item Description Inlet Fitting Part Number A. 1 to 5 Gallon suction hose & tube assembly EZMix B. 5 Gallon suction hose & rod assembly C. 5 Gallon suction hose & rod assembly D. 55 Gallon suction hose & rod assembly E. 55 Gallon suction hose & rod assembly

29 Airmix Accessories A. B. C /4" air hose assemblies, conductive A. 5 ft. long air hose with 1/4 F NPS fittings B. 10 ft. long air hose with 1/4 F NPS fittings C. 16 ft. long air hose with 1/4 F NPS fittings D. 25 ft. long air hose with 1/4 F NPS fittings E. 28 ft. long air hose with 1/4 F NPS fittings F. 32 ft. long air hose with 1/4 F NPS fittings G. 50 ft. long air hose with 1/4 F NPS fittings /16" AIRMIX CONDUCTIVE FLUID HOSE Item Description S/S Fittings Part Number Plated Fittings Part Number A. 10 ft. long fluid hose with #5 JIC fittings B. 16 ft. long fluid hose with #5 JIC fittings C. 25 ft. long fluid hose with #5 JIC fittings D. 32 ft. long fluid hose with #5 JIC fittings E. 50 ft. long fluid hose with #5 JIC fittings AND 55 GALLON DIRECT DRIVE AGITATORS A. G5-5 Gallon agitator with side-mount bracket B. G5-5 Gallon S/S agitator with cover and nylon blade C. G55-55 Gallon S/S agitator with cover and nylon blades agitator/elevator SYSTEM FOR 55 GALLON DRUMS A. M3R55E - Gear drive agitator w/elevator and S/S 55 gallon drum cover B. G55E - Direct drive agitator w/elevator and S/S 55 gallon drum cover PUmp lubricant A. Lubricant T (1/4L) for solvent-based paints B. Lubricant T (1 quart) for solvent-based paints C. Lubricant T (1 gallon) for solvent-based paints D. Lubricant P (1 quart) for polyurethanes E. Lubricant P (1 gallon) for polyurethanes Airmix Accessories 24. Protective cream A. Protective cream - Pack of B. Protective cream - Pack of C. Protective cream - Pack of

30 Exel Industries... An International Presence 30 EXEL North America, consisting of our Canadian, American and Mexican subsidiaries, is a wholly owned subsidiary of EXEL Industries. They bring three finishing and extrusion brands under one company banner. The three brands offer the widest range of controlled application equipment for finishing and extrusion in the world. Our Vision To remain the global leader in high value added custom and standard solutions for controlled applications of powders and fluids, thick or thin, in the industrial and automotive markets. Our Values We are a team of people with integrity that have a mission-to-serve with a sense of urgency in delivering the right solution and service through our network of Solution and Service Centers. Our Mission Making Manufacturers More Competitive Finishing Extrusion

31 Introducing Exel North America, Inc. Exel... North American Leader The New Exel North America, Inc. 31 Precision Finishing and Extrusion Brands Non-electrostatic guns, pumps and accessories for thin fluids Electrostatic application equipment for liquid and powder Guns, pumps and accessories for thick fluids Full Range of Equipment Manual Airspray Manual Airmix Manual Liquid Electrostatic Manual Powder Automatic Non-Electrostatic Automatic Liquid Electrostatic Automatic Powder Fluid Delivery Pumps & Accessories Extrusion (RAM) Pumps & Accessories Plural Component Systems & Accessories Manufacturing Markets Served Wood Industrial Feeder Plants Automotive West Chicago, Illinois Scarborough, Ontario Monterrey, Mexico West Chicago, Illinois Scarborough, Ontario Monterrey, Mexico Livonia, Michigan Scarborough, Ontario Monterrey, Mexico Livonia, Michigan Scarborough, Ontario Monterrey, Mexico Exel R&D, Testing, Training, Distribution and Manufacturing Locations Over 100 North American Solution and Service Centers for Customer Sales and Service Making Manufacturers More Competitive

32 OTHER CATALOGS Wood Guide Automatic Spray Circulation Pumps Manual Airspray Glue & Adhesives Guide* Manual Electrostatic Plural Component Systems Automatic Electrostatics General Catalog Manual Powder Equipment 1 Component Extrusion 2 Component Extrusion * Coming Soon Your Solution & Service Center is: Making Manufacturers More Competitive EXEL North America, Inc. North American Headquarters Wood and General Industrial Division 1310 Washington Street West Chicago, IL Phone: (630) Fax: (630) EXEL North America, Inc. Automotive and Feeder Plant Division Merriman Rd. Livonia, MI Phone: (734) Fax: (734) EXEL Industrial Canada, Inc Serving All Markets 931 Progress Ave., Unit 7 Scarborough, Ontario M1G 3V5 Phone: (416) Fax: (416) EXEL, S.A. de C.V. Serving All Markets Moisés Sáenz 1510, Col. Leones Monterrey, N. L. México, CP Phone: (81) Fax: (81) March 2006 Revision #2 Catalog # LT