VCN-2000 VENOM Nitrous System

Size: px
Start display at page:

Download "VCN-2000 VENOM Nitrous System"

Transcription

1 VCN-2000 VENOM Nitrous System Installation/Operation Manual Software Installation Harness Installation Hose Installation COMPLETELY READ THIS MANUAL BEFORE STARTING INSTALLATION Copyright 2000 Python Injection, Inc. All rights reserved.

2 General Information With the statements below, the term Nitrous Oxide System shall refer to the complete VENOM VCN-2000 Nitrous Oxide System, including any hoses, wires, connectors, bottles, modules or software. Limited Warranty Every Nitrous Oxide System is rigorously tested at the factory. Python Injection warrants the Nitrous Oxide System to be free from manufacturer s defects for a period of 90 days from the date of purchase. During this period, if any of the Nitrous Oxide System components are found to be defective by Python Injection, we, at our option, will repair or replace the defective Nitrous Oxide System components. No allowances will be made for labor or other installation charges. Consequential damages are not covered. There will be no warranty coverage for engine damage. Limitation of Liability TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL PYTHON INJECTION, INC. OR ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO CITATIONS, DAMAGE TO VEHICLE, VEHICLE ENGINE, OR COMPONENTS OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE/INSTALLATION OR INABILITY TO USE/INSTALL THE NITROUS OXIDE SYSTEM OR THE FAILURE OF PYTHON INJECTION, INC OR ITS SUPPLIERS TO PROVIDE SUPPORT SERVICES, EVEN IF PYTHON INJECTION, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE ENTIRE LIABILITY OF PYTHON INJECTION, INC. UNDER THE WARRANTY SHALL BE LIMITED TO THE AMOUNT PAID BY THE PURCHASER FOR THE NITROUS OXIDE SYSTEM. BECAUSE SOME STATES/JURISDICTIONS DO NOT ALLOW EXCLUSION OR LIMITATION OF LIABILITY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU. PURCHASER MUST NOTIFY PYTHON INJECTION, INC. OF ANY DEFECT OR MALFUNCTION OF THE NITROUS OXIDE SYSTEM PROMPTLY UPON DISCOVERY. Conditions That Will Void Warranty The following conditions will void the VCN-2000 Warranty: Using incorrect Vehicle-Specific Installation Instructions. Opening the VCN-2000 Module, the LCD display, or valve assembly or performing any unauthorized modifications to the VCN-2000 Module or its components. Damage caused by heat, water, improper electrical connection, physical damage or improper installation. Modifying (shortening, lengthening, cutting, etc.) the VENOM harness.

3 What Is Included The VCN-2000 kit includes all of the necessary parts to perform a professional installation of the VCN-2000 Nitrous System. Check the contents of the kit prior to beginning the installation. If any part of the kit is missing, contact the place of purchase for replacement. The VCN-2000 kit should include: Installation Manual The VCN-2000 Module The VCN-2000 LCD Screen The VCN-2000 Software Installation Floppy Disks Programming Cable Nitrous Bottle and Brackets Wiring Harness Injector Harness 20 Nitrous Hose 2 ½ Nitrous Hose with Nozzle Valve Assembly Connector Splices Product and Warranty Registration Card Wire Ties Necessary Tools Vehicle-Specific Instructions (Located on floppy disks - See Software Installation ) A pair of pliers are necessary to squeeze the connectors into place. The VCN-2000 module must be located inside the vehicle s passenger compartment. Therefore, a drill and drill bit will be necessary to provide passage between the engine compartment and the passenger cabin. A drill and drill bit may also be necessary to tap into the air intake. A Digital Volt/Ohm Meter Wrench to attach hoses to Nitrous Bottle and Nitrous Valve

4 Product Registration A product and warranty registration card is included with the VCN-2000 kit. This card must be filled out and received by Python Injection to activate the warranty. Have this information available if you call for technical assistance. Online registration is also available at Technical Assistance Technical assistance regarding the installation process is available Monday through Friday between 8 A.M. to 5 P.M. Pacific Standard Time. Assistance is provided directly by Python Injection by calling Be prepared to have your serial number ready when calling. Do not call the place of purchase for technical assistance questions. Online Technical Support is also available at Precautions Observe the following precautions while installing the VCN-2000 Wire Harness and Injector Harness: Never install the Wire Harness or Injector Harness or work under the hood of a vehicle with the engine running. Some engine parts become extremely hot. Use caution when working under the hood. Read over the entire installation manual prior to starting the installation. Familiarize yourself with the procedures. Installation is very easy if the procedures are followed. Wear safety glasses at all times during the installation process. Nitrous is a gas that is under extreme pressure and can cause frostbite if it comes in contact with the skin.

5 Software Installation Note: Installed with the VCN-2000 Software is a program that prints vehicle specific instructions for the Wiring Harness and the Injector Harness. Therefore, the VCN-2000 software must be installed before the wiring harnesses can be installed. Only one instruction set can be accessed with the Vehicle-Specific Instructions. Make sure that you enter the correct information. Software Requirements The VCN-2000 Nitrous System Software requires: Pentium PC or equivalent (75 MHz recommended) Windows 95 or Windows 98 with 12 MB RAM (Recommended) 8 MB RAM and 3 MB Hard disk space 3 ½ Floppy Disk Drive Serial Port Printer - to print Vehicle-Specific Instructions Installation Steps 1. Close all programs 2. Click on Run on the Start Menu 3. Type A:\Setup.exe 4. Follow the setup prompts The VCN-2000 Setup program will automatically create a shortcut in the Start Menu to the VCN-2000 Programming Software and the VCN-2000 Vehicle-Specific Instructions Software.

6 Vehicle-Specific Instructions Software The Vehicle-Specific Instructions are needed to install the VCN-2000 Wire Harness. These instructions have the wire colors needed to connect the wiring harnesses to your vehicle. To get these instructions: 1. Click on the Vehicle-Specific Instructions Software shortcut. This will be located in the Start Menu after you complete the VCN-2000 installation procedure. 2. Select the vehicle year, make, and model. NOTE: The Vehicle Specific Instructions Software will only display one set of instructions. Make sure the vehicle year, make, and model are correct before you click View Instructions. 3. When you are sure that the vehicle year, make, and model are correct, click on the View Instructions button. 4. Click on the Print button to print the instructions. 5. The next time that this program runs, the selected vehicle instructions will immediately be displayed. Figure 1 The Vehicle Specific Instructions Software Display Figure 2 Make sure you chose the correct vehicle

7 Wire Harness Installation Figure 1: Wiring Harness Installation Note: Vehicle-specific installation instructions are included with the VCN-2000 Programming Software. Install the software (read the section Software Installation ) to print the Vehicle-Specific Instructions. Tip: Two 9 wiring harnesses are included with the VCN-2000 kit - a main harness and an injector harness. This allows enough cable to install the VCN-2000 module inside the passenger compartment. Since the module is re-programmable, install it in a location that is easily accessible.

8 Installation Instructions WARNING The VENOM Harness uses shielded cables. Cutting or modifying the cable will destroy it. This will also void the warranty. NOTE: The VENOM Module is susceptible to electrical noise. You must maintain 6 of clearance between any of the wires within the VENOM harness and any of the following vehicle components: Spark Plug Wires Ignition Coil(s) Alternator Stereo Amplifiers Stereo Speakers A wire diagram is provided on the previous page. 1. Decide where the module will be located. The VCN-2000 module must be located within the passenger compartment. The glove box or under the passenger seat is a good location for the VCN-2000 module. 2. Locate a path for the wire harnesses and drill any necessary holes. 3. Run the wire harnesses along the decided path. 4. Connect power and ground: Connecting power to the VCN-2000 Red Wire: The VCN-2000 red wire should be connected directly to the vehicle s positive battery terminal. The end of the red wire has an eyelet that will connect directly to the vehicle s positive battery terminal lug. NOTE: There are two ground wires on the VENOM Main Harness. Both must be connected to the negative battery terminal. Connecting ground to the VCN-2000 Black Wire: The VCN-2000 black wire should be connected directly to the vehicle s negative battery terminal or a chassis ground. The end of the black wire has an eyelet that will connect directly to the vehicle s negative battery terminal lug. 5. Secure the harness. Use the supplied wire harness ties and adhesive mount bases to secure the harness. Ensure that the harness is not routed too closely to any rotating engine parts or parts that get hot enough to melt the cable insulation.

9 Connecting The Harness To The Sensors WARNING: SOME VEHICLES USE SHIELDED SENSOR CABLES! Some vehicles use shielded sensor cables to eliminate electrical interference that otherwise could affect the operation of the vehicle s on-board computer. These shielded wires are similar to the coax cable found in your home audio or TV wiring. A shielded cable contains two conductors - the signal wire and the shield. The shield is the outer conductor and is usually made of a steel braid, which is connected to the vehicle ground. Any electrical interference that is induced onto the wire is grounded. This effectively shields the signal wire from capturing this interference, which could affect the electrical signal. If the wire splice provided is applied to a shielded wire, the wiring harness on the vehicle will be damaged. In addition, the signal and the ground will be shorted together which could cause erratic vehicle operation, a no start condition, damage to the vehicle s computer system or all of the above. You can identify a shielded wire by one of the following methods: A shielded wire will be slightly larger than a single wire. A shielded wire will usually be a single color, such as gray or black without any color tracers. You may see the braided shielding protruding out of the end of the wire where it connects to the sensor. A shielded wire may feel rough under the insulation in comparison to a single conductor wire, which is smooth. There are three sensor connections that must be made: Throttle Position Sensor This is a three wire sensor located on the throttle body. This sensor will be connected to the cable on the VENOM Main Harness that is color coded YELLOW. Oxygen Sensor This may be a single, two, three, or four wire sensor located on the exhaust pipe. This sensor will be connected to the VENOM Main Harness wire that is color coded WHITE. Engine RPM Input This signal may be obtained from the Ignition Coil, Tachometer Lead, or DIS Module (if equipped). This input signal will be connected to the VENOM Main Harness wire that is color coded GREEN. The Vehicle-Specific Instructions Software is used to determine what wire color code on each sensor the harness should be connected to. See Software Installation for more information.

10 These connections are made using the blue splice connectors supplied in the kit. The splice connectors are folded over the existing sensor wire and snapped together. The appropriate wire from the VENOM Main Harness is then connected to the blue splice. This effectively taps into the existing sensor signal. DO NOT cut the existing sensor wire, as this will affect the engine operation. If the sensor uses a shielded wire, you must trim the shielding at the end of the wire to obtain an adequate connection into the inner signal wire. WARNING: The VENOM Main Harness uses shielded sensor wires. DO NOT cut the VENOM Harness to shorten or lengthen the harness. If the harness is too long, route the harness to utilize the entire cable. Looping the wire and securing it with a wire tie is acceptable. If the harness to a sensor is too short, you may obtain an extension cable in various lengths for a nominal charge. Connecting The Injector Harness NOTE: The VCN-2000 Module provides additional fuel to support the addition of nitrous through the existing injectors. It accomplishes this by pulsing the injectors. This procedure deals with the connection to each injector. If the connection to the injector is not complete or secure, the cylinder associated with that injector will run lean, causing engine damage. If the wire from the VENOM Injector Harness is connected to the wrong side of the vehicle harness, the module will be permanently damaged, causing incorrect operation and engine damage. It is highly recommended, and required in some cases, that all the electrical connections to the injectors be tested with a digital volt/ohm meter (VOM). This meter may be obtained at any electronics store (such as Radio Shack) for about $ The VENOM Injector Harness will need to be connected to each injector on the vehicle. Depending on your application, you will need to make 4, 5, 6, or 8 connections.

11 The injector is supplied battery voltage through the ignition switch on one terminal. This is referred to as the Voltage Supply. The other terminal is connected to the vehicle s on-board computer. The computer supplies the ground to energize the injector, which provides fuel to the engine. This is referred to as the Ground Circuit. The wires on the VENOM Injector Harness must be connected to the Ground Circuit of EACH injector. Failure to provide a good connection will cause the engine to run too lean, causing engine damage. The Vehicle-Specific Instructions Software will identify what color wire is which circuit. For EXAMPLE, the printed instructions will look like: Injector 1 EXAMPLE ONLY EXAMPLE ONLY EXAMPLE ONLY Ground Circuit: Blue/Yellow wire connects to blue wire on VENOM Harness Voltage Supply: Purple/Pink No Connection Injector 2 EXAMPLE ONLY EXAMPLE ONLY EXAMPLE ONLY Ground Circuit: Red/Green wire connects to blue wire on VENOM Harness Voltage Supply: Purple/Pink No Connection Injector 3 etc CRITICAL NOTE: In rare cases, the Voltage Supply circuit color code and the Ground Circuit color code will be the same color, therefore making it impossible to identify one circuit from the other. If this is the case on your vehicle, a voltmeter will be required to determine which wire is the Ground Circuit. Refer to Test Procedure 1B at the rear of this manual if both wires on the injector have the same color code. In this example, one of the blue wires on the VENOM Injector Harness will be connected to the blue/yellow wire of the number one injector and one of the blue wires on the VENOM Injector Harness will be connected to the red/green wire of injector 2. Once all of the blue wires of the VENOM Injector Harness are connected to the Ground Circuit of EACH injector, proceed to Procedure 1A at the rear of this manual to test the electrical connection.

12

13

14 Hose/Bottle Installation Instructions 1. The nitrous bottle should be mounted in the trunk of the vehicle. The bottle is mounted at an angle with the bottle s valve at the highest point. The bottle s valve outlet should be pointed downward toward the floor of the trunk. See Figure 2B. 2. The VENOM valve assembly should be mounted, using the supplied hardware, beneath the hood within 2.5 feet of the nitrous entry point into the engine. Nitrous is injected into the engine in the air inlet just before the throttle body. See Figure 2C. NEVER install the valve assembly in the trunk, passenger compartment or farther than 2.5 feet from the entry point into the engine. Failure to follow these installation requirements will result in engine damage! 3. Route the 20 nitrous hose from the trunk beneath the vehicle into the engine compartment. Avoid the exhaust system, braking components, and suspension components. Connect the nitrous line to the inlet of the valve assembly. Figure 3: Valve Assembly Hookup 4. Connect one end of the 2.5 nitrous line to the outlet of the valve assembly. Using the supplied hardware, connect the other end of the line to the air intake duct, approximately 8-inches from the throttle body plate. See Figure Connect the Positive (RED) wire of the valve harness to the positive terminal of the battery. Connect the Negative (BLACK) wire of the valve harness to the negative terminal of the battery. Connect the four terminal connector of the VENOM Main Harness to the Valve Assembly. Installation of the VENOM VCN-2000 Nitrous System is complete.

15

16

17 VCN-2000 Operating Instructions The VCN-2000 Programming Software Introduction to the VCN-2000 Programming Software The VCN-2000 Programming Software is designed to interface with the VCN-2000 Module. By setting the values of three operating modes, you can fully customize the VCN-2000 Module. Once the values are downloaded to the VCN-2000 Module, you can switch between modes just by turning the power off and turning it back on with the red mode button (on the module) pressed. The software is not needed to switch between modes, only to change the values of the three modes. The three operating modes are: Linear Mode Drag Mode Timed Mode Starting the Software The VCN-2000 installation program will automatically create a shortcut in your Start Menu to the VCN-2000 Programming Software. Click on the shortcut to start the software. When the VCN-2000 Programming Software starts, you will have to select a couple of values so the VCN-2000 Module can work with your vehicle. Those values are: 1. The Number of cylinders in your vehicle 2. The type of Ignition System 3. The Throttle Position Sensor (TPS) offset voltage

18 The TPS offset voltage is the voltage at the output of the wire of the Throttle Position Sensor when the throttle is closed. This can be measured with a Digital Volt Meter. The VCN-2000 Module uses this voltage for a basis in calculating the proper throttle angle. It is critical that this entry is accurate. If it is not, the VCN-2000 Module can inject nitrous at the incorrect throttle angle. This voltage is usually between 0.5 and 1.2 volts. You can determine if y ou have entered the correct voltage if the Throttle Angle % reading on the LCD Display is at 0% when the module is re-installed on the vehicle. If it reads too high you will need to INCREASE the value entered into the TPS Offset Field. If the reading is 0% and as soon as you begin to depress the throttle, the Throttle Angle on the LCD Display increases, then the value you entered is okay. You may have to fine tune this entry to obtain optimum operation. You will need to re-program the module each time y ou change this value in the software. This can be time consuming so it is recommended that the actual voltage is measured and the correct value is entered into the software. Setting the Operating Mode Values 1. Linear Mode In this mode, the VCN-2000 Module starts to inject nitrous at the Throttle Angle that you specify, but only after the RPM you specify has been reached. As the throttle is increased, the VCN-2000 Module increases nitrous flow to the maximum amount that you specify. Step 1: Input Linear Mode Parameters With this mode, the Activation Throttle Angle, the Activation RPM, and the Maximum Nitrous Level can be changed. When this mode is selected, the VCN-2000 Module will release nitrous in a linear slope with the throttle position, only after the selected throttle angle and the selected activation RPM have been reached. At 100% throttle angle, the maximum nitrous amount selected will be released.

19 2. Drag Mode In this mode, the VCN-2000 Module monitors the engine RPM and Throttle Position Sensor (TPS). Once the RPM that you specify has been reached and the VCN-2000 Module senses that the throttle is wide open, the VCN-2000 Module activates nitrous flow in the amount you specify and for the time that you specify. Step 2: Input Drag Mode Parameters This mode allows the Activation RPM and the Nitrous Level to be changed. When the Activation RPM is reached and the vehicle is at wide open throttle, the VCN-2000 releases the selected nitrous amount until the vehicle drops under the selected Activation RPM or until the throttle position is no longer at 100%. 3. Timed Mode In this mode, the VCN-2000 Module allows nitrous flow in the amount that you specify and for the amount of time you specify, only after the Throttle Angle and the RPM limits (specified by you) are reached.

20 Step 3: Input Timed Mode Parameters This mode allows the Activation Throttle Angle, the Activation RPM, the Nitrous Level, and the Nitrous Injection Time to be changed. When the selected Activation RPM and the selected Activation Throttle Angle are reached, the VCN-2000 Module will open the valve to the selected nitrous level for the selected injection time. After all of the values are selected, they have to be downloaded to the VCN-2000 Module. This is done with the supplied VCN-2000 Programming Cable. The programming cable will have a DB9 (like the end of a printer cable but smaller) connector on one end and a DIN6 (similar to the end of a mouse that plugs into a computer) on the other end. The DB9 connector will plug into the serial port of you computer. The other end will plug into the VCN-2000 module. Downloading the Program After you select the desired values for the three modes, you must download those values to the VCN-2000 Module. Before you can download the program you must: 1. Connect the module to the computer via the programming cable. THE VEHICLE HARNESS MUST BE REMOVED FROM THE MODULE. Before you connect the module to the computer, make sure that the power switch is in the off position. Once the programming cable is connected, turn the module power switch to the on position. 2. Click on the Step 4: Download Your Program hyperlink on the VCN-2000 Programming Software.

21 3. Select the Serial Communication Port. On most computers it will be COM1. 4. Verify that the module is correctly connected to the computer and click the Start Download button on the VCN-2000 Programming Software. If the VCN-2000 Module is not correctly connected to the computer then a Communication Error will occur. Check the programming cable connections and try to download the program again. 5. After the download is complete, remove the module from the programming cable and connect it to the Main Wiring Harness (the Main Wiring Harness should already be installed on the vehicle). If you want the selected values to be saved within the VCN-2000 Programming Software click on Save Your Program and Exit. The VCN-2000 Module Operation How to change modes To change the mode, turn the VCN-2000 Module power switch to the off position. Turn the module power on while holding the red mode button. The LCD display will scroll through the three modes. When you find the mode that you want, release the button. The mode will be selected. The LCD Display RPM The Current Engine RPM Exhaust The Current Status of the Fuel (either Rich or Lean) Throttle The Throttle Angle Mode L for Linear, D for Drag, or T for Timed Inj Pw Injector pulse width in milliseconds System Status Will display the current action of the module. System Ready means that the VCN-2000 Module is idle and System Active means that the module is injecting nitrous.

22 Obtain the following information from the label on the module for future reference. Have this information available when calling for technical support. Don t forget to send in the Product and Warranty Information Card. Date of Purchase Place of Purchase Serial Number Software Version Python Injection and VENOM Performance are registered trademarks of Python Injection, Inc. Windows 95 and Windows 98 are registered trademarks of the Microsoft Corporation. Copyright 2000 Python Injection, Inc. All Rights Reserved

VCN-1000 Venom Computerized Nitrous System

VCN-1000 Venom Computerized Nitrous System VCN-1000 Venom Computerized Nitrous System Installation and Operation Manual COMPLETELY READ THIS MANUAL BEFORE STARTING INSTALLATION Revised July, 2001 2001 Python Injection, Inc. All rights reserved.

More information

MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012

MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012 MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty

More information

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393 MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly

More information

MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020

MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 INSTALLATION INSTRUCTIONS 1 MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 Important: Read these instructions before attempting this installation! Parts Included: 1 - MSD Stacker Ignition

More information

MSD 7AL-3, Ignition Control PN 7230

MSD 7AL-3, Ignition Control PN 7230 MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,

More information

Installation Instructions Diesel Nitrous System (#82028)

Installation Instructions Diesel Nitrous System (#82028) Installation Instructions Diesel Nitrous System (#82028) Thank you for choosing ZEX. If at any time you have questions regarding this or any of our products, please call our Nitrous Help support line at

More information

MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595

MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark

More information

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi MSD Pro-Billet Ready-to-Run Chrysler Distributor PN 8391-331/354 Early Hemi PN 8389-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there

More information

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with

More information

MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69150C / 69150R

MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69150C / 69150R FORM 69150C/R MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69150C / 69150R To ensure you are using the most current instruction sheet, please visit www.malloryfirestorm.com. CAUTION! The

More information

MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010

MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 Parts Included 1 Ignition Controller, PN 6010 1 Pro-Data+ Software CD 1 Harness 1 Parts Bag 6 Timing Modules Optional Accessories

More information

BAK1500 INSTALLATION/OWNER'S MANUAL Compact Amplified Subwoofer

BAK1500 INSTALLATION/OWNER'S MANUAL Compact Amplified Subwoofer BAK1500 INSTALLATION/OWNER'S MANUAL Compact Amplified Subwoofer PREPARATION Getting Started Thank you for purchasing the Dual BAK1500 compact amplified subwoofer. Although Dual has attempted to ensure

More information

MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013

MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013 MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013 Parts Included: 1 - Ignition Controller, PN 6013 1 - Pro-Data+ Software CD 1 - Parts Bag 1 - Mounting Template Optional Accessories: Hand

More information

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573 MSD Pro-Billet Ready-to-Run Ford Flathead, 1949-1953 PN 8573 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your

More information

USER GUIDE 1 USER GUIDE

USER GUIDE 1 USER GUIDE USER GUIDE 1 USER GUIDE 1 TABLE OF CONTENTS IN THE BOX...3 NAVIGATING THE MENUS...3 MENU LAYOUT...3 UPDATE YOUR PROGRAMMER...4 CONNECT WITH THE MOTORCYCLE...5 TUNE YOUR MOTORCYCLE...6 ADDITIONAL FEATURES...8

More information

Part #82064 Add-A-Stage EFI Nitrous System

Part #82064 Add-A-Stage EFI Nitrous System 1 INSTRUCTIONS Part #82064 Add-A-Stage EFI Nitrous System Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning

More information

MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69050S / 69050R

MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69050S / 69050R FORM 69050S/R MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69050S / 69050R To ensure you are using the most current instruction sheet, please visit www.malloryfirestorm.com. CAUTION! The

More information

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 Parts Included 1 - Ignition Controller, PN 6011 1 - Pro-Data+ Software CD 1 - Harness 1 - Parts Bag 1-2-Bar MAP Sensor Optional Accessories

More information

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 INSTALLATION INSTRUCTIONS MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 Parts Included: 1 - Ignition 1 - Wiring Harness 1 - Parts Bag 1 - CD ROM WARNING: When installing the SB6, disconnect

More information

MSD-8 Plus Ignition PN 7805

MSD-8 Plus Ignition PN 7805 MSD-8 Plus Ignition PN 7805 Note: Solid Core spark plug wires cannot be used with an MSD Ignition. Parts Included: 1 - MSD-8 Plus Ignition 1 - Mag Pickup Extension Harness, PN 8860 4 - Vibration Mounts

More information

MSD Pro-Billet Chevrolet HEI Distributor PN 8365

MSD Pro-Billet Chevrolet HEI Distributor PN 8365 MSD Pro-Billet Chevrolet HEI Distributor PN 8365 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering

More information

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our

More information

TBX10A INSTALLATION/OWNER'S MANUAL 10" Sealed Enclosure with Built-in Amplifier

TBX10A INSTALLATION/OWNER'S MANUAL 10 Sealed Enclosure with Built-in Amplifier TBX10A INSTALLATION/OWNER'S MANUAL 10" Sealed Enclosure with Built-in Amplifier Getting Started Thank you for purchasing the Dual TBX10A 10" ported enclosure with built-in amplifier. Although Dual has

More information

MSD-8 Plus Ignition PN 7805

MSD-8 Plus Ignition PN 7805 MSD-8 Plus Ignition PN 7805 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team

More information

MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302

MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your

More information

CSA CERTIFIED Conforms to UL 507

CSA CERTIFIED Conforms to UL 507 Installation tion Instructions Please read and save these instructions! TURBO/MAXX12 Volt All Weather RV Ventilator Fans P/N 00-965001 Deluxe Model 1200T WITH THERMOSTAT P/N 00-965007 Standard Model 3550

More information

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360

MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360 MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor

More information

DISTRIBUTORLESS IGNITION SYSTEM Installation and Adjustment Instructions

DISTRIBUTORLESS IGNITION SYSTEM Installation and Adjustment Instructions DISTRIBUTORLESS IGNITION SYSTEM Installation and Adjustment Instructions 1.0 INTRODUCTION: Congratulations on your purchase of a Holley Distributorless Ignition System! Holley cannot and will not be responsible

More information

MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653

MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653 MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with

More information

#82037 Race EFI Nitrous System

#82037 Race EFI Nitrous System 1 INSTRUCTIONS #82037 Race EFI Nitrous System Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation,

More information

MSD Pro-Billet Chrysler Distributor PN Early Hemi

MSD Pro-Billet Chrysler Distributor PN Early Hemi MSD Pro-Billet Chrysler Distributor PN 83891-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your

More information

DWS404 DWS524 DWS654 DWS684 DWS694. DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers

DWS404 DWS524 DWS654 DWS684 DWS694. DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers DWS404 DWS524 DWS654 DWS684 DWS694 DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers PREPARATION Safety Guidelines Thank you for purchasing the DWS Series car speakers. Although Dual has attempted

More information

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink.

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink. Quick Start Guide This is only a quick start guide. A full wiring and installation manual is included in PCLink. Installer I/O Table Wire Description Installer Connection Typical Application +14V Bat Full

More information

MSD Start/Retard Control PN 8982

MSD Start/Retard Control PN 8982 MSD Start/Retard Control PN 8982 IMPORTANT: Read the instructions before attempting installation. Parts Included: 1 - Start/Retard Control, PN 8982 4 - Retard Modules, 0, 2, 3, 4 1 - Wiring Kit 4 - Mounting

More information

#82087 Gen III High Output Nitrous System

#82087 Gen III High Output Nitrous System INSTRUCTIONS #82087 Gen III High Output Nitrous System Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation,

More information

Thank you for your purchase Off-ROad NOtice: PROduct WaRNiNgs:

Thank you for your purchase Off-ROad NOtice: PROduct WaRNiNgs: Thank you for your purchase. Please, read the instructions and watch the video before installing the JMS Progressive N20 Controller. Configuration and installation videos are available online: www.jms-nos.com.

More information

Model AS-RC3260 TV Cart. Rolling Cart for Audio Mount System & Flat Panel TVs

Model AS-RC3260 TV Cart. Rolling Cart for Audio Mount System & Flat Panel TVs Model AS-RC3260 TV Cart Rolling Cart for Audio Mount System & Flat Panel TVs GETTING STARTED Introduction Congratulations on the purchase of your new Helios AS-RC3260 Rolling Cart. For maximum benefit,

More information

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440

MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will

More information

INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System

INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE CAR SHOW VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY

More information

RS-110 Rainfall Sensor Installation Guide

RS-110 Rainfall Sensor Installation Guide RS-110 Rainfall Sensor Installation Guide for XR440 and XR5 Data Loggers September 2015 Revision 1.1 1 Disclaimer The following warranty and liability disclaimer apply to this product. PACE SCIENTIFIC

More information

IVTM Installation Manual

IVTM Installation Manual Integrated Vehicle Tire Pressure Monitoring IVTM Installation Manual 2nd edition Copyright WABCO 2006 Vehicle Control Systems An American Standard Company The right of amendment is reserved Version 002/06.06(us)

More information

INSTRUCTIONS. #82028 Diesel Nitrous System. Thank you for choosing ZEX products; we are proud to be your manufacturer of choice.

INSTRUCTIONS. #82028 Diesel Nitrous System. Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. 1 INSTRUCTIONS #82028 Diesel Nitrous System Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. Why our nitrous system is better: 2 Performance enthusiasts know the potential

More information

MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740

MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issued with

More information

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever

More information

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi

MSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi MSD Pro-Billet Ready-to-Run Chrysler Distributor PN 8391-331/354 Early Hemi PN 8389-392 Early Hemi Important: Read these Instructions before attempting the installation. Note: An MSD Ignition Control is

More information

STC2 Car Kit. Installation Guide

STC2 Car Kit. Installation Guide STC2 Car Kit Installation Guide Box Contents When you unpack your STC2 Car Kit, it should include everything as shown below: Suction Cup Mount & Screws Surface Preparation Cleaning Kit (To clean a surface

More information

INSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE

INSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE INSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE 2650-1846-77 Rev. B Details: Temperature Rating: -40 C to 85 C/-40 F to 185 F Vibration Specification: 20 g continuous, 50 g shock Inputs: o 4 EGT

More information

JAMP-500HR06-RCRP. Installation and Operation Instructions. 500W 4-CH Amplifier Kit For Harley Road Glide Fairing with Rear Speakers

JAMP-500HR06-RCRP. Installation and Operation Instructions. 500W 4-CH Amplifier Kit For Harley Road Glide Fairing with Rear Speakers 500W 4-CH Amplifier Kit For 2006-2013 Harley Road Glide Fairing with Rear Speakers # JAMP-500HR06-RCRP 2013 J&M Corporation. All rights reserved. 5/13 Installation and Operation Instructions Product Description

More information

AEROMOTIVE Part # L Mustang Digital FMU INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # L Mustang Digital FMU INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 17113 4.6L Mustang Digital FMU INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that

More information

AEROMOTIVE Part # INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 16303 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried

More information

#82044 Race Diesel Nitrous System

#82044 Race Diesel Nitrous System INSTRUCTIONS #82044 Race Diesel Nitrous System Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation,

More information

MSD Programmable Shift Controller PN 7559

MSD Programmable Shift Controller PN 7559 MSD Programmable Shift Controller PN 7559 WARNING: During installation, disconnect the battery cables. When Disconnecting, always remove the Negative cable first and install it last. Parts Included: 1

More information

JAMP-250HR06P. Installation and Operation Instructions. 250W Amplifier Kit For Harley RoadGlide Fairing

JAMP-250HR06P. Installation and Operation Instructions. 250W Amplifier Kit For Harley RoadGlide Fairing 250W Amplifier Kit For 2006-2013 Harley RoadGlide Fairing # JAMP-250HR06P 2013 J&M Corporation. All rights reserved. 5/13 Installation and Operation Instructions Product Description This exciting new J&M

More information

Before continuing with the installation, here are a few definitions you should be aware of:

Before continuing with the installation, here are a few definitions you should be aware of: MSD Pro-Billet Distributor Cadillac V8 (368, 425, 472, 500), PN 8363 AMC V8, PN 8519 Jeep Inline-6, PN 8516 Chevrolet Inline-6 (194, 230, 250, 292), PN 8515 ONLINE PRODUCT REGISTRATION: Register your MSD

More information

KIT CONTENTS. Multimeter or test light Wire crimpers or soldering equipment. Wire terminals & connectors 10A inline fuse

KIT CONTENTS. Multimeter or test light Wire crimpers or soldering equipment. Wire terminals & connectors 10A inline fuse RUSSELL FORD 5.0L COMPLETE EFI PLUMBING KIT INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new complete fuel system kit. If you have any questions, please call

More information

MSD Boost Control Module PN 77631

MSD Boost Control Module PN 77631 MSD Boost Control Module PN 77631 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

MSD Pro-Billet Ready-to-Run Distributors Pontiac, PN 8528 Oldsmobile, PN 8529

MSD Pro-Billet Ready-to-Run Distributors Pontiac, PN 8528 Oldsmobile, PN 8529 MSD Pro-Billet Ready-to-Run Distributors Pontiac, PN 8528 Oldsmobile, PN 8529 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor,

More information

U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M

U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof

More information

MegaSquirt III for Gen 3 HEMI. Hardware Install THE FOLLOWING SENSOR PART NUMBERS APPLY TO ALL HARNESSES FOR ENGINES 2004 TO CURRENT:

MegaSquirt III for Gen 3 HEMI. Hardware Install THE FOLLOWING SENSOR PART NUMBERS APPLY TO ALL HARNESSES FOR ENGINES 2004 TO CURRENT: MegaSquirt III for Gen 3 HEMI MegaSquirt controllers are experimental devices intended for educational purposes. MegaSquirt controllers are not for sale or use on pollution controlled vehicles. Check the

More information

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor

More information

JAMP-500HC-JHD1. Installation and Operation Instructions

JAMP-500HC-JHD1. Installation and Operation Instructions ROKKER XTP Series 4-Channel Amplifier Kit For Connection To The Jensen HD1BT Radio As Installed Into 1998-2013 Harley Davidson Ultra/ Street/Electra Glide Fairings # JAMP-500HC-JHD1 2014 J&M Corporation.

More information

DRAGO. Corn Header Manual f HEADSIGHT.COM

DRAGO. Corn Header Manual f HEADSIGHT.COM DRAGO Corn Header Manual 09020801f HEADSIGHT.COM 574.546.5022 About Headsight Headsight Contact Info Headsight, Inc. 4845 3B Road Bremen, IN 46506 Phone: 574-546-5022 Fax: 574-546-5760 Email: info@headsight.com

More information

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts!

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts! 2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit

More information

Installation Instructions EFI V8 BB Direct Port Nitrous System (82063)

Installation Instructions EFI V8 BB Direct Port Nitrous System (82063) Installation Instructions EFI V8 BB Direct Port Nitrous System (82063) Thank you for choosing ZEX. If at any time you have questions regarding this or any of our products, please call our ZEXTEK support

More information

Instruction Sheet SRSR SERIES. Rotating Sliding Rail System

Instruction Sheet SRSR SERIES. Rotating Sliding Rail System Instruction Sheet SRSR SERIES Rotating Sliding Rail System THANK YOU Thank you for purchasing the SRSR Series Rotating Sliding Rail System. Please read these instructions thoroughly before assembling this

More information

MSD Boost Control Module PN 7763

MSD Boost Control Module PN 7763 MSD Boost Control Module PN 7763 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

Sprayer Control. Manual for SprayLink Cable Installations. Tank. Jet Agitator. Agitator Valve. Diaphragm Pump. Pressure Transducer.

Sprayer Control. Manual for SprayLink Cable Installations. Tank. Jet Agitator. Agitator Valve. Diaphragm Pump. Pressure Transducer. Sprayer Control Plumbing & Installation Manual for SprayLink Cable Installations Tank Jet Tank Shut-Off Diaphragm Pump Electric Ball s Transducer Strainer Relief Regulating Copyrights 2012 TeeJet Technologies.

More information

Installation Power Management Unit Battery Cables and Battery Harness

Installation Power Management Unit Battery Cables and Battery Harness Installation Power Management Unit Battery Cables and Battery Harness Important Safety Messages SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during installation

More information

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501

MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501 MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN 85561 Extra Tall, PN 8547 with Locked-Out Timing, PN 85501 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product

More information

Performance Series 400W 4-CH Amplifier Kit For Harley Road Glide Fairing with Rear Speakers JMAA-4000HR06-RCR

Performance Series 400W 4-CH Amplifier Kit For Harley Road Glide Fairing with Rear Speakers JMAA-4000HR06-RCR Performance Series 400W 4-CH Amplifier Kit For 2006-2013 Harley Road Glide Fairing with Rear Speakers # JMAA-4000HR06-RCR 2018 J&M Corporation. All rights reserved. 6/18 Installation and Operation Instructions

More information

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES PART NUMBER: 250-9545 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON:2.7,3.3, 3.5, 5.0 FORD F-150 RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS

More information

Product Description. Installation Instructions. Fig. A

Product Description. Installation Instructions. Fig. A Performance Series 360w RMS 4-Channel Amplifier Kit For 2015 & Later Harley RoadGlide Custom # JMAA-3600HR15-RC 2015 J&M Corporation. All rights reserved. 12/15 Installation and Operation Instructions

More information

Model: PSB100. Rear Parking Sensor System. Installation Manual TABLE OF CONTENTS

Model: PSB100. Rear Parking Sensor System. Installation Manual TABLE OF CONTENTS Rear Parking Sensor System Model: PSB100 Installation Manual TABLE OF CONTENTS Warnings...2 Product Description...3 Packing List...3 Installation Instructions...4 Mounting the Sensors...4 Installing the

More information

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES PART NUMBER: 250-9618 AUTOMATIC TRANSMISSION 250-9619 MANUAL TRANSMISSION GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: CHEVY SONIC/ SPARK (ALL MODELS) RECOMMENDED TOOLS PERSONAL & VEHICLE

More information

INSTALLATION GUIDE. Universal System for Zero Turn Mowers

INSTALLATION GUIDE. Universal System for Zero Turn Mowers INSTALLATION GUIDE Universal System for Zero Turn Mowers Table of Contents General Information 1 Important Notice to Purchaser 2 Specifications 2 Intended Usage 2 Important Information 3 General Safety

More information

EXCELSIOR-HENDERSON MOTORCYCLE MANUFACTURING COMPANY 805 HANLON DRIVE BELLE PLAINE, MINNESOTA TELE: /FAX:

EXCELSIOR-HENDERSON MOTORCYCLE MANUFACTURING COMPANY 805 HANLON DRIVE BELLE PLAINE, MINNESOTA TELE: /FAX: All text, photographs, and illustrations in this handbook are based on the most current product information available at the time of publication. Product improvements or other changes may result in differences

More information

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573

MSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573 MSD Pro-Billet Ready-to-Run Ford Flathead, 1949-1953 PN 8573 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor

More information

ELITE 1000/1500 Dodge SRT QUICK START GUIDE HT

ELITE 1000/1500 Dodge SRT QUICK START GUIDE HT E N G I N E M A N A G E M E N T S Y S T E M S ELITE 1000/1500 Dodge SRT4 03-05 QUICK START GUIDE HT-140940 LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the HaltechTM Programmable Fuel Injection

More information

JAMP-500HC06-ULP. Installation and Operation Instructions. 500W Amplifier Kit For Harley Ultra (Not For RoadGlide Ultra)

JAMP-500HC06-ULP. Installation and Operation Instructions. 500W Amplifier Kit For Harley Ultra (Not For RoadGlide Ultra) 500W Amplifier Kit For 2006-2013 Harley Ultra (Not For RoadGlide Ultra) # JAMP-500HC06-ULP 2013 J&M Corporation. All rights reserved. 5/13 Installation and Operation Instructions Product Description This

More information

DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual

DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual Installation Instructions Tech Support: 856.768.8300 TechSupport@GlowShiftGauges.com DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual (1) Gauge (2) Controllers

More information

MaxxECU quickstart guide ( )

MaxxECU quickstart guide ( ) Be a tuning mastermind. Like us. MaxxECU quickstart guide (2019-02-01) Online help! maxxecu.com/support Wiring diagrams Installation help Pinout Support maxxecu.com/support Legal disclaimer All performance

More information

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES GENERAL APPLICABILITY FORD FIESTA ( AT/MT) KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION PART# 1 1 CRUISE CONTROL MODULE 250-2813 2 1 SWITCH HARNESS 250-2760 3 1 PEDAL INTERFACE HARNESS 250-2821 4 1

More information

UNIVERSAL GAUGE WIRE HARNESS

UNIVERSAL GAUGE WIRE HARNESS 2650-1797-00 UNIVERSAL GAUGE WIRE HARNESS For Installing Auto Meter Electric Speedometer, Tachometer, And Short Sweep Electric Oil Pressure, Water Temperature, Fuel Level, and Volt Meter Gauges. This harness

More information

V8 Gen. V Ford Mustang 2010 Update

V8 Gen. V Ford Mustang 2010 Update V8 Gen. V Ford Mustang 2010 Update There were several updates to the Ford Mustang in the 2010 model year. This document outlines the differences between the installation steps necessary for the 2010 Mustang

More information

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572

MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 MSD Pro-Billet Chevrolet V8 Tach Drive Distributor PN 8571 with Vacuum Advance, PN 8572 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition is required with this

More information

Prop-Tech Vacuum Analyzer

Prop-Tech Vacuum Analyzer Electronic Carburettor / Injector Balancing Tool 1. WARNING THIS PRODUCT IS A PROFESSIONAL TOOL WHICH SHOULD ONLY BE OPERATED BY A COMPETENT TRAINED TECHNICIAN AND ONLY FOR THE PURPOSE WHICH IT WAS DESIGNED

More information

Track Rocker Installation Instructions

Track Rocker Installation Instructions Track Rocker Installation Instructions For Installing Painless Part Numbers: 58103: 8-Switch Customizable Track Rocker Switch Panel w/ Flanged Mount 58106: 6-Switch Customizable Track Rocker Switch Panel

More information

INSTALLATION INSTRUCTIONS MECHANICAL GAUGES

INSTALLATION INSTRUCTIONS MECHANICAL GAUGES 1062650-1966-77 MECHANICAL GAUGES QUESTIONS: If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s), please contact Hardin Marine

More information

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES PART NUMBER: 250-9631 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: ALL MODELS (AT/MT) RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY

More information

T H E U L T I M A T E L A S E R D E F E N S E S Y S T E M

T H E U L T I M A T E L A S E R D E F E N S E S Y S T E M S P E E D O F L I G H T P R O T E C T I O N CINCINNATI MICROWAVE 5440 West Chester Road West Chester OH 45069 Sales/Service 800-433-3487 EscortRadar.com 2014 CINCINNATI MICROWAVE. ESCORT, Laser ShifterPro,

More information

JAMP-660SG15-CVO. Installation Instructions. ROKKER XXR 660w RMS Dual-Amplifier Kit For Harley CVO Street Glide

JAMP-660SG15-CVO. Installation Instructions. ROKKER XXR 660w RMS Dual-Amplifier Kit For Harley CVO Street Glide ROKKER XXR 660w RMS Dual-Amplifier Kit For 2015-2018 Harley CVO Street Glide # JAMP-660SG15-CVO 2017 J&M Corporation. All rights reserved. 9/17 Installation Instructions Product Description This is the

More information

Before continuing with the installation, here are a few definitions you should be aware of:

Before continuing with the installation, here are a few definitions you should be aware of: MSD Ford Billet Distributors PN 8473: 2.3L, PN 8580: 351C, 351M, 400, 429, 460 PN 8582: 289, 302, PN 8584: 351W PN 85805: 351W w/edelbrock Victor Jr. Intake Important: Read these instructions before attempting

More information

3-Stage Retard PN 8970

3-Stage Retard PN 8970 3-Stage Retard PN 8970 IMPORTANT: Read the instructions before attempting the installation. Parts Included: 1-3-Stage Retard Control 4 - Mounting Screws 4 - Mounting Grommets 6 - Retard Modules, 2, 3,

More information

PLEASE READ BEFORE CALLING OR RETURNING PRODUCT. EXTREMELY IMPORTANT!!!

PLEASE READ BEFORE CALLING OR RETURNING PRODUCT. EXTREMELY IMPORTANT!!! Thank you for your purchase of WeaponX Smart Direct Fire Ignition Coil System for your vehicle. The following are the instruction manuals for your ignition system kit. Please read carefully and enjoy your

More information

MSD Single Cylinder Programmable Ignition PN 4217

MSD Single Cylinder Programmable Ignition PN 4217 MSD Single Cylinder Programmable Ignition PN 4217 Parts Included: 1 - PN 4217 1 - PN 4217 Wire Harness 1 - CD Rom 9609 1 - Parts Bag 1 - Serial Cable WARNING: During installation, disconnect the battery

More information

NEXUS. Introduction SENSOR MODULE &

NEXUS. Introduction SENSOR MODULE & 2650-1056 INSTALLA AT TION INSTRUCTIONS NEXUS SENSOR MODULE & REMOTE ASSEMBLY IMPORTANT WEAR SAFETY GLASSES 60 80 40 100 FUEL 20 PSI 0 AUTO METER PRODUCTS INC. c 2004-6463 0 10 20 10 20 BOOST VAC In.Hg

More information

JMAA-2000HR15. Installation and Operation Instructions. 200w Performance Series Amplifier Kit For Harley RoadGlide/Ultra

JMAA-2000HR15. Installation and Operation Instructions. 200w Performance Series Amplifier Kit For Harley RoadGlide/Ultra 200w Performance Series Amplifier Kit For 2015-2019 Harley RoadGlide/Ultra # JMAA-2000HR15 2018 J&M Corporation. All rights reserved. 9/18 Installation and Operation Instructions Product Description J&M

More information

INSTALLATION INSTRUCTIONS. Revision 3.1.1

INSTALLATION INSTRUCTIONS. Revision 3.1.1 INSTALLATION INSTRUCTIONS Revision 3.1.1 Table of Contents INTRODUCTION... 4 INSTALLATION OVERVIEW... 5 Included Parts... 6 DEVICE WIRING... 7 Required Parts... 7 Guidelines... 7 Wiring Diagram... 8 Compatible

More information

60 PSI Boost Gauge. For Product Numbers: MT-DV01_60, MT-WDV01_60

60 PSI Boost Gauge. For Product Numbers: MT-DV01_60, MT-WDV01_60 60 PSI Boost Gauge For Product Numbers: MT-DV01_60, MT-WDV01_60 Red: 12v Constant (un-switched) Source (+) Orange: 12v Dimmer (switched) Source (+) (optional) White: 12v Ignition (switched) Source (+)

More information

INSTRUCTIONS. #82044 Race Diesel Nitrous System

INSTRUCTIONS. #82044 Race Diesel Nitrous System INSTRUCTIONS #82044 Race Diesel Nitrous System Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. Kit Parts List Description Qty. Description Qty. Nitrous Solenoid 2.088

More information