Important: This guide is compatible with the NISS1HT firmware version 3.11 and lower. Vehicle Application Guide...

Transcription

1 Platform: DBALL/DBALL Rev.: 060 Update Alert: Firmware updates are poed to e web on a regular basis. We recomme at you check for firmware a/or inall guide updates prior to inalling is product. Inallation Guide The NISSHT is an OEM transpoer immobilizer override via data (no key required). Interfaces directly wi e late models of Nissan Infinity ignition immobilizer syems to provide seamless, safe a secure syem integration when adding an aftermarket remote arter. Note: NISSHT is compatible wi all key type Nissan a Infiniti vehicles (it does NOT cover knob or Push-to-Start (PTS) vehicles). See NISSHT for knob or NISSHT a NISSHT for PTS. Important: This guide is compatible wi e NISSHT firmware version. a lower. Iex Vehicle Application Guide... Inallation (Wiring Diagram Vehicle Wiring Reference Chart)... Vehicle Connection Types... Programming Module Programming... Module Reset Ha Reset... Features Options Li... Features Programming... LED Diagnoics Troubleshooting... Limited One-Year Consumer Warranty... Quick Reference Guide Infiniti, Nissan Suzuki are regiered trademarks a property of eir respective companies. 05 Directed. All rights reserved.

2 Platform: DBALL/DBALL Vehicle Application Guide Rev.: 060 Page The table below lis e vehicles a features which are compatible wi is product. Refer to e following pages for more information on inallation wiring, programming a troubleshooting for ese vehicles. Vehicles PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm wi OEM remote RS-RAP Shut Down (Retained ACC Power) RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin Chevrolet City Express D D Infiniti FX5 D D D FX5 D D D G5 D D D G5 Coupe D D D QX56 D D D Nissan Z D D D Altima D D D Armada D D Cube D D Frontier D D JUKE D D Maxima D Micra D D NV D D D NV00 D D Pafier D D Que D D D Rogue D D Rogue Select D D Sentra D D Titan D Versa D D Versa Note D D Xterra D D D X-Trail D D D Suzuki Equator D D D Lege: W: Wire-to-Wire (WW) DL: OE Door Lock Alarm Controls D: Data-to-Data (DD) FOB: Sync CAN Interface w/ FOB Remote : DD WW KI: Ignition Key Switch Interface PK: Transpoer Immobilizer Override RS: Remote Start Engine Controls SS: Integrated Security Monitoring SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-E-Brake Status ST-Ignition Status 05 Directed. All rights reserved.

3 Platform: DBALL/DBALL Wiring Diagram Rev.: 060 Page BCM White Connector (right of eering column) Disarm Unlock: Pin 7 Arm Lock: Pin 8 (-) Hood Status Input (+) Brake Input [] (AC) Tach Input (-) Trunk Input (-) Door Status Input (-) E-Brake Status Input [] (-) Unlock Output [] (-) Lock Output Starter Remote (-) Grou (+) V (+) Accessory Output (+) Accessory Output (if required) (+) Ignition Output/Input (+) Start Output (-) Lock Output (-) Unlock Output (-) Trunk Output (+) Parking Lights Output (+) Starter Output (-) GWR (Status) To Vehicle Refer to Note: To avoid double lock a unlock, Door Lock Control on DATA mu be set to disable on DBALL. See Feature Option Li section to disable Door Lock Control on DATA. Automatic Headlamp See p. Wiring Reference Chart HS CAN High: Pin HS CAN Low: Pin Diagnoic Connector OBDII (connector side view) Clutch Switch See p. Wir. Ref. Chart HS CAN High: Tan/Black: HS CAN Low: Tan: Data (Vehicle side): Yellow: 8 Data (Key side): Orange/Yellow: 9 CUT Connect clutch input to (+)V or (-)Grou. See p. Wir. Ref. Chart [] Clutch Output: Yellow/Red: Clutch Input (+ or -): Brown/Red: (+) V (+) V: Red: (-) Grou: Black: (-) E-Brake Status Output: Black/White: (-) Automatic Headlamp Shut-Off: Green/Black: (-) Door Status Output: Green/White: (-) Trunk Sense Output: Red/Black: (AC) Tach Output: Violet/White: 5 (+) Brake Status Output: Gray: 6 Clock: Yellow/Black: 0 Data: Orange/Black: (-) Hood Status: Blue/Red: Data: Pin RF Prog. button LED DBALL/ DBALL 0 0: Blue/White: (-) GWR (Status) Input 8: Violet: (+) Starter Input 7: Pink/White: (+) Parking Lights Input : Red/White: (-) Trunk Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+)V RX (-) Grou TX XKDD65 Not required in DD mode. Clock: Pin N.A.T.S. NATS Antenna Connector at ignition switch. [] These wires are optional connections required on some remote arters, which do not support is signals in DD. [] Only required on vehicles equipped wi a factory alarm or if e door locks are not controlled rough CAN. Unless specified oerwise, all connectors are displayed from e wire side, wi e exception of e OBDII diagnoic connector. 05 Directed. All rights reserved.

4 Platform: DBALL/DBALL Vehicle Wiring Reference Chart Rev.: 060 Page Vehicles Compatibility Chevrolet City Express 05 Infiniti Vehicle Blue or Red, pin Vehicle Connection Types See e Vehicle Wiring Reference Chart above Autolight OFF at BCM Autolight Clock Data Arm Disarm Connection Pin Wire Color Type (see next page) Pin Wire Color Pin Wire color Pin Wire Color Pin Wire color Gray Pink Lt.Green 8 Light Blue 7 Gray FX Automatic only Green Green/Black Brown 8 Empty* 7 Empty* FX Automatic only Green Green/Black Brown 8 Empty* 7 Empty* G (+) Gray/Red, pin Blue Green Brown 8 Empty* 7 Empty* G5 Coupe (+) Gray/Red, pin Blue Green Brown 8 Empty* 7 Empty* QX Automatic only Red/Yellow Green Brown 8 Empty* 7 Empty* Nissan 50Z Off (+) Gray/Red, pin Not needed Green/White Brown 8 Empty* 7 Empty* Altima (-) Green/Red, pin Green/Yellow Pink Yellow/Black 8 Empty* 7 Empty* Armada Automatic only Red/Yellow Green Brown 8 Empty* 7 Empty* Cube 009- (+) Brown, pin Not needed Pink/Blue Lt. Green 8 White/Black 7 White/Red Frontier 005- (+) Red or Blue, pin Not needed Gray Brown 8 Light Blue 7 Gray Frontier 05 (+) Blue or Red, pin Gray Gray Brown 8 Light Blue 7 Gray Juke 00- (+) Brown, pin Not needed Pink Lt. Green 8 Red 7 Blue Maxima (-) Green/Red, pin Green/Yellow Pink Yellow/Black 8 Empty* 7 Empty* Maxima 00 Off (-) Green/Red, pin Green/Yellow Pink Green 8 Empty* 7 Empty* Micra 05 (+) Lt. Green, pin Not needed Pink Lt.Green 8 Gray 7 White NV 0-5 Automatic only Not needed Green Brown 8 Light Blue 7 Yellow NV N/A Not needed Pink Lt.Green 8 Pink 7 Black Pafier 005- Automatic only Gray Gray Brown 8 Light Blue 7 Gray Que Automatic only Red/Yellow Orange Brown 8 Empty* 7 Empty* Que 00 Off Automatic only Red/Yellow Orange Brown 8 Empty* 7 Empty* Rogue 008- Automatic only Not needed Green Brown 8 Red 7 Blue Rogue Select 0-5 N/A Not needed Green Brown 8 Red 7 Violet or Blue Sentra 007- (+) Brown, pin Not needed Red Orange 8 Brown 7 White Sentra 0-5 (+) Brown, pin Not needed Pink Lt. Green 8 Violet 7 Blue Titan Automatic only Red/Yellow Green Brown 8 Empty* 7 Empty* Versa 0-5 (+) Lt.Green, pin Not needed Pink Lt. Green 8 Gray 7 White Versa 007- (+) Brown, pin Not needed Pink Lt. Green 8 Yellow 7 Brown Versa Note 0-6 (+) Lt.Green Not needed Pink Lt.Green 8 Gray 7 White Xterra (+) Red or Blue, pin Not needed Gray Brown 8 Light Blue 7 Gray X-Trail Automatic only Not needed Red Orange 8 Brown 7 White Suzuki Years Door Lock Type Option (see below) Clutch Type Option (see next page) Autolights OFF Information Transpoer Data Wires Factory Arm/Disarm at BCM Equator 009- (+) Not needed Gray Brown 8 Light Blue 7 Gray Auto Headlamp Shut Off TYPE Relay Pin 0 Cut Relay Pin 87a Auto Headlamp wire at e vehicle. See e Wiring Reference Chart. TYPE Wire Side View of BCM (+) V a 0 85 Pin of -pin conn: Green/Black The Auto Headlamp wire will show: Grou: when e switch is at AUTO. Open circuit: when e switch is at any oer position. Auto Headlamp wire at e vehicle. See e Wiring Reference Chart. Pin of -pin conn: Green/Black The Auto Headlamp wire will show Grou when e switch is at any position oer an AUTO. 05 Directed. All rights reserved.

5 Platform: DBALL/DBALL Module Programming Rev.: 060 Page 5 Refer to e LED Diagnoics section on page 9 for more information a for troubleshooting purposes. Important Make all e required connections to e vehicle, as described in e wiring diagram(s) fou in is guide, a double check to ensure everying is correct prior to moving onto e next ep. Warning! To take advantage of advanced features, you mu use XpressVIP.5 or higher. Using version.9 or. will limit available functions a features.. Connect e interface module to your computer using e XKLoader.. Open an Internet Explorer browser (version 6 or higher), a go to The detail of e platform a firmware at is currently saved on e interface module will be iicated in e top right corner of e page.. Select e year, make a model of e vehicle; e page will refresh to display e compatible firmware.. In e search result page, select Flash Staa inall, a follow e inructions provided on e screen. 5. Once you have configured your options, click on e FLASH button to upload e firmware onto e interface module. 6. The following message will be displayed when e upload is completed: The flashing is successfully completed. You may now unplug e kit. You can now proceed wi e programming inructions below. DD Inallation If required for your inallation, connect e 0-pin, -pin a -pin harnesses to e module, en connect e -pin DD harness. DD 0-pin -pin -pin OR WW Inallation If required for your inallation, connect e 0-pin a -pin harnesses to e module, en connect e -pin harness to e module. DD 0-pin -pin -pin Wait until e LED turns ON solid red. Note: To skip e transpoer programming a use convenience features only, press e programming button 5 times. Insert a turn e key to e ignition position. The LED flashes orange. Key IN OFF IGN START Key at IGN Turn e key to e OFF position, en back to e ignition position. The LED turns ON solid green for secos, en shuts off. Key IN OFF IGN START Key IN OFF IGN START x secs Off Turn e key to e OFF position a remove it from e ignition barrel. Key OUT OFF IGN START You have successfully completed e module programming sequence. 05 Directed. All rights reserved.

6 Platform: DBALL/DBALL Module Reset Rev.: 060 Page 6 A module reset will only erase programming performed in e previous eps. All settings (firmware) a settings flashed to e module using e web config tool will not be affected. OR DD Inallation If required for your inallation, connect e 0-pin, -pin -pin harnesses to e module. Press a hold e programming button, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e 0-pin -pin harnesses to e module. Press a hold e programming button, en connect e -pin harness to e module. 5 DD 0-pin DD 0-pin -pin -pin -pin -pin Wait secos until e LED turns ON solid orange en release e programming button. The LED en turns ON solid red. Release Ha Reset Warning Again Executing a Ha Reset! A ha reset will revert e flashed firmware back to its default settings. Depeing on e inallation, some settings (such as RFTD a DD options) may have to be reconfigured. See e Feature Option Li section of is guide. OR DD Inallation If required for your inallation, connect e 0-pin, -pin -pin harnesses to e module. Press a hold e programming button, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e 0-pin -pin harnesses to e module. Press a hold e programming button, en connect e -pin harness to e module. 5 DD 0-pin DD 0-pin -pin -pin -pin -pin Wait secos until e LED turns ON solid orange, a wait 0 more secos until e LED arts to flash orange a red. Release e programming button. The LED turns ON solid red. Release 05 Directed. All rights reserved.

7 Platform: DBALL/DBALL Feature a Option Li Rev.: 060 Page 7 It is recommeed to configure all e features a options lied below using e configuration tool fou on e module flashing page on The web offers more options; however, manual configuration of e features is possible using e information on is page. * Default Feat. Operation / Option Description. No RF Output* Module is connected to a remote arter using a aa inallation. Module is connected to an XL0 using an RSR or RXT inallation (when RFTD Output. RFTD Output available). Type Module is connected to SmartStart using an RSR or RXT inallation. SmartStart (when available). Unlocks only e driver door when e button is fir pressed, a unlocks Unlock Driver. Driver priority* all doors when it is pressed a seco time wiin 5 secos. Priority. All Unlocks all doors when e button is fir pressed.. Disabled* The vehicle doors will not lock automatically. 5 6 Automatic Controlled Door Lock Smart OEM Alarm Control Parking Light Control On Data Door Lock Control On Data The vehicle doors will lock when ignition is turned ON a unlock when. Ignition ignition is OFF. The vehicle doors will lock when e brake pedal is applied a unlock. Brake when ignition is OFF. The vehicle doors will lock when speed is sensed a unlock when ignition. Speed is OFF. The OEM alarm will not be controlled by DBALL upon remote art. No. Disabled disarm or arm comma will be executed at e beginning or e of e sequence; it mu be controlled by e Remote Starter. Smart OEM Alarm Control will behave like a aa Safelock feature on. Safelock a remote arter. It will unlock at e beginning of e sequence, a relock after art a shutdown. Smart OEM Alarm Control will synchronize wi e OEM alarm so at it will disarm a rearm e vehicle in e remote art sequence, only when required. The reason for is is, factory alarm control mu often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as e horn to honk. When possible, Smart OEM Alarm Control will monitor e alarm a door lock atus to detect if e. Enabled* disarm or rearm is required. If e vehicle is unlocked or is not equipped wi factory alarm, e disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor e remote arter actions so at e factory alarm control is not done twice. A remote arter, for which e Safelock feature is active, will work perfectly wi is option a will make it invisible to e user.. Disabled The remote arter parking lights wire mu be connected in e vehicle.. Enabled* The parking lights will be controlled by CAN wires.. Disabled Disable e control of e door locks via CAN.. Enabled - Type // EU Enable e control of e door locks via CAN - Type messages.. Enabled - Type // US* Enable e control of e door locks via CAN - Type messages. Feature 6: Door Lock Control on Data See VAG on page to determine e correct door lock type for your vehicle. When set to OFF, e remote arter door lock wires mu be connected in e vehicle. 05 Directed. All rights reserved.

8 Platform: DBALL/DBALL Rev.: 060 Feature Programming To enter feature programming routine - Turn e ignition ON, en OFF. - Wiin 5 secos, press a HOLD e programming button until e LED turns ON orange (after secos). Release e Programming button. - The LED will flash green once slowly to iicate e feature number is. After a short delay, e LED flashes red rapidly to iicate e current option of feature (i.e. x green followed by x red iicates feature is set to option ). The flashing sequence will repeat until a new comma is entered. Changing feature options - Press e lock/arm or unlock/disarm button on aftermarket transmitter to change e option of e selected feature. - The LED flashes red rapidly e number of times equal to e current option number. After a short delay, e LED flashes green slowly e number of times to iicate e current feature. The flashing sequence will repeat until a new comma is entered. Accessing anoer feature - Press a release e programming button a number of times to advance from e current feature to e next desired feature. - The LED flashes green slowly e number of times equal to e feature number. After a short delay, e LED flashes red rapidly to iicate e current option of e current feature. The flashing sequence will repeat until a new comma is entered. When e maximum number of features or options is reached, e LED will art flashing again from e fir feature or option. Once a feature is programmed - Oer features can be programmed. - The feature programming can be exited. Programming Button Exiting feature programming - No activity for 0 secos; after 0 secos, e LED will turn ON orange for secos to confirm e e of e programming sequence. OR - Press a HOLD e programming button for secos. After secos, e LED will turn ON orange for secos to confirm e e of e programming sequence. Page 8 05 Directed. All rights reserved.

9 Platform: DBALL/DBALL LED Diagnoics a Troubleshooting Rev.: 060 Page 9 LED Status Description Troubleshooting Module Programming Off Off Module has no power. Make sure e DD harness is connected or at e Volt is present between e red a black wires. If e Volt is present, e module may be defective. Red Waiting to begin e programming sequence. Refer to e wiring diagram to make sure at all e connections are correct. Orange CAN BUS detected Normal operation. Waiting for e completion of e bypass programming sequence. x secs Green x secos Module has been successfully programmed. Normal operation. Module Programming - Error Codes Red x en Orange x Clock bus error. Yellow/Black did not detect e expected signal. Refer to e wiring diagram to make e right connections. Red x en Orange x DATA bus error. Orange/Black did not detect e expected signal. Refer to e wiring diagram to make e right connections. x Red x Bypass data not detected. Check e bypass line connections a make sure ey are not inverted. x Red x Bypass processing error. Bypass calculation failed. Reset e module a try again. External Module Synchronisation red, red, orange red, red, en orange x 0 Active Grou While Running Green OBDII feature not supported. GROUND OUT ON (GWR) comma received. Diagnoic data bus not detected. Some features are not supported by SmartStart. This can be caused by missing wire connections or module haware limitation. Refer to e wiring inallation section to check e connections. Oerwise, e Grou While Running (atus) signal was lo or was never received by e module. Commas can come from RF, DD or WW. Red Orange IGNITION ON comma received. Oerwise, e ignition signal was not received by e module. In a WW inall, it will show only if e ignition input wire is used. quickly Green Quickly START ON comma received. Oerwise, e art signal was not received by e module. In a WW inall, it will show only if e ignition input wire is used. DD WW Commas x Orange x Lock comma received. x Orange x Unlock comma received. If e bypass module fails to flash, it means e module did not receive e signal. Commas can come from RF, DD or WW. x Orange x Trunk comma received. 05 Directed. All rights reserved.

10 Platform: DBALL/DBALL Limited One Year Consumer Warranty Rev.: 060 Page 0 For a period of ONE YEAR from e date of purchase of a Directed Electronics remote art or security product, Directed Electronics. ( DIRECTED ) promises to e original purchaser, to repair or replace wi a comparable recoitioned piece, e security or remote art accessory piece (hereinafter e Part ), which proves to be defective in workmanship or material uer normal use, provided e following coitions are met: e Part was purchased from an auorized DIRECTED dealer; a e Part is returned to DIRECTED, poage prepaid, along wi a clear, legible copy of e receipt or bill of sale bearing e following information: consumer s name, address, telephone number, e auorized licensed dealer s name a complete product a Part description. This warranty is nontransferable a is automatically void if e Part has been modified or used in a manner contrary to its inteed purpose or e Part has been damaged by accident, unreasonable use, neglect, improper service, inallation or oer causes not arising out of defect in materials or conruction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold wiin e United States of America a Canada. Parts sold outside of e United States of America or Canada are sold AS-IS a shall have NO WARRANTY, express or implied. Some ates do not allow limitations on how long an implied warranty will la or e exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights a you may also have oer rights at vary from State to State. DIRECTED does not a has not auorized any person or entity to create for it any oer obligation, promise, duty or obligation in connection wi is Part. For furer details relating to warranty information of Directed products, please visit e support section of DIRECTED s website at: This Interface kit / Data Bus Interface part has been teed on e lied vehicles. Oer vehicles will be added to e select vehicle li upon completion of compatibility teing. Visit website for late vehicle application guide. DISCLAIMER: Uer no circumances shall e manufacturer or e diributors of e bypass kit / data bus interface part(s) be held liable for any consequential damages suained in connection wi e part(s) inallation. The manufacturer a it s diributors will not, nor will ey auorize any representative or any oer iividual to assume obligation or liability in relation to e interface kit / data bus interface part(s) oer an its replacement. N.B.: Uer no circumances shall e manufacturer a diributors of is product be liable for consequential damages suained in connection wi is product a neier assumes nor auorizes any representative or oer person to assume for it any obligation or liability oer an e replacement of is product only. Protected by U.S. Patents: 5,79,55; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; Cdn. Patent:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;,0,97;,6,670;,5,089; European Patent:,05,8; Pat. Peing:,9,06. Made in Canada. 05 Directed. All rights reserved.

11 Quick Reference Guide DBALL/DBALL-NISSHT Li of Available Commas Notes Note at e information below is for Viper, Cliffo a Pyon models. Icons a commas may differ depeing on e remote bra a model purchased. Refer to your auorized inallation center for more information. Button(s) Actions Press hold for seco to lock. Press hold for seco to unlock. Press hold for seco to remote art. Press hold for 5 secos to activate e trunk release (optional). x + x + x + Press once, en to activate e rear hatch/tail glass release (optional).* Press times, en to activate e panic mode. Press once, en to reset e remote arter runtime. * This output is configurable. see your auorized inallation center for more information. 06 Directed. All rights reserved.