INSTALLATION INSTRUCTIONS READ "SAFETY MANUAL" AND "USER MANUAL" BEFORE STARTING THE UPS INSTALLATION LAYOUT INFORMATION FANS FANS REMOVIBILE COVER

Transcription

1 INSTLLTION INSTRUCTIONS RED "SFETY MNUL" ND "USER MNUL" BEFORE STRTING THE UPS INSTLLTION LYOUT INFORMTION FNS IR FLOW IR FLOW! HOT FNS REMOVIBILE COVER FRONT VIEW SIDE VIEW RER VIEW PERSPECTIVE VIEW PERSPECTIVE VIEW WITH OPEN DOOR NOTE: 1000 MINIMUM FRONT DISTNCE TO THE WLL (RECOMMENDED 10) BCK CBLE ENTRY Power Type MIN INFORMTION kv / MST 1 MST 1 / 1 / Operating temperature C 0-40 Max relative humidity in operation % 90 % (without condensation) WHEEL CENTER SWIN SWBY SWMB SWOUT Max installation height Power Loss@load 100% (1) Power Loss@load % Net Dimension W x D x H Shipping Dimension W x D x H kcal / h B.T.U. / h kcal / h B.T.U. / h 1000m at nominal power (-1% power for every 100m above 1000m) max 4000m 6, , , , x 10 x x 1145 x 2085 Net Weight Kg 4 4 Shipping Weight Kg ir Flow 3 m / h FRONT BOTTOM VIEW Current dispersed to ground (2) m < 0 Degree of protection IP 20 (1) 3.97 B.T.U. / h = 1 kcal / h (2) The load leakage current is added to the one of the UPS on the ground protection conductor

2 INPUT LINE 3PH + N + PE INPUT C LINE - SINGLE LINE 1 Max admitted neutral current POWER INFORMTION WRNING -THE INPUT OUTPUT ND PROTECTIVE ERTHING CONDUCTORS MUST BE SIZED FOLLOWING RTED VOLTGE ND CURRENT, SHOWN IN THE TBLES BELOW, ND CCORDING TO DOMESTIC REGULTIONS ND CURRENT STNDRDS -THE PROTECTIVE ERTHING CONDUCTOR (PE) MUST BE CONNECTED FIRST BEFORE TO PROCEDE CONNECTING INPUT / OUTPUT CBLES Terminal (L1, L2, L3) or (L1Byp, L2Byp, L3Byp) INPUT C LINE - DUL SEPRTED LINE (Remove the bars connecting input mains - bypass line) INPUT LINE 3PH + N + PE Max admitted neutral current Terminal (L1, L2, L3) INPUT BYPSS LINE 3PH + N + PE Max admitted neutral current Terminal (L1Byp, L2Byp, L3Byp) (2) (1) (1) The neutral terminal is the same for input mains and bypass line (2) The is the same for all connections BTTERY INPUT (+), (-), N + PE bsolutely max size of battery string protection device Terminal (+), (-) BTTERY DC INPUT (The PE conductor from battery cabinet must be connected at the UPS earthing terminal only) Rated nominal battery voltage 3 end of discharge voltage Max size of battery string protection device: gl / gg fuse ar fuse (2) OUTPUT LINE 3PH + N + PE Rated current Output protection (recoended values for selectivity) Normal fuses (gl - gg) Thermal magnetic switches (C curve) Terminal (L1, L2, L3) 1 OUTPUT C LINE 1 2 x h (battery capacity) 2,5 x h (battery capacity) In / 4 In / 4

3 REMOVE JUMPERS FOR DUL INPUT POWER DETILS NUT M10 SPRING WSHER diam. 10 PLIN WSHER diam. 10 N L1 L1B L2 L2B L3 L3B PLIN WSHER diam. 10 SCREW M10 INPUT LINE (N / L1 / L1B / L2 / L2B / L3 / L3B) see detail DETIL INPUT - OUTPUT - BTTERY CBLES OUTPUT LINE (L3 / L2 / L1 / N) see detail L3 L2 L1 N SCREW M8 SPRING WSHER diam. 8 PLIN WSHER diam. 8 PROTECTIVE ERTH (PE) see detail «B» - N + BTTERY LINE (- / N / +) see detail DETIL «B» PROTECTIVE ERTH (PE) CBLES

4 B D D E E (PE) SECTION - B SECTION B-B SECTION D-D SECTION E-E (PE) NEUTRL ( N ) INPUT / OUTPUT BTTERY ( + / - ) BTTERY ( N )

5 SIGNL S and COMMUNICTION DETILS FNS Slot for parallel card ( OPTIONL ) RS232 Port USB Port S400 Port R.E.P.O. Counication slot 2 Counication slot 1 Cold start Schuko socket fuse Schuko socket FNS ZONE INPUT FUSES FNS SERVICE BYPSS RESERVED EXTERNL SYNC EXT. BTTERY TEMP PROBE SWITCH OUT UX CONTCT UX RELY SLOT BRKE ROD FRONT VIEW RER VIEW UXILIRY SIGNL S