Haakon Ellingsen AS Årenga 8, N-1340 Skui P.O. Box 184, N-1309 Rud Phone Fax

Transcription

1 NORWEGIAN DISTRIBUTOR: Ellingsen NOR INSTRUMENTS Haakon Ellingsen AS Årenga 8, N-1340 Skui P.O. Box 184, N-1309 Rud Phone Fax post@ellingsen.biz F02-BU-E Rev. 4-Sep 2010 Biffi Italia s.r.l. Headquarters, Sales department, Fiorenzuola d Arda - Italy tel fax biffi_italia@biffi.it website:

2 Product Brochure F 0 2 technology in a pill The ICON2000 series introduced intelligent actuators for the severest duties......the F02 concentrates the highest actuation technology in the smallest electric actuator

3 Features More than half a century ago Biffi started its business in valve actuation. Its world-wide leadership has been built through continuous innovation and the ability to face the new challenges that a fast changing environment comes up with. It was in 1992 that BIFFI started its intelligent actuator campaign. Since then Biffi intelligent actuators have been welcomed by all the major companies around the world, in many different applications in the most hostile environments. The best solution for each application Thanks to its experience, know-how and product range, Biffi can supply its Customer any actuator solution. New quarter-turn electric actuators for small part-turn valves and dampers, with ICON intelligence With the F02 series, Biffi introduces a compact (up to Nm) quarter-turn electric actuator for the operation of low-torque part-turn valves and dampers with the highest innovative actuation technology. Why ask for modular construction if you can have all the main features integrated in one single actuator? The latest technology in market actuation proposes a wide use of modular construction. BIFFI introduces a new philosophy in the electric actuators construction with all the main possible basic variables integrated in one single product. For very specific features, BIFFI proposes a very easy modular integration for advanced improvement. With its 8 kilos, the F02 is the most innovative all-in-one actuator available on the market. Not only does it include a whole range of essential design features such as ICON intelligence, but can also incorporate Bluetooth TM Wireless connectivity. 2

4 3

5 One single version to cover the whole range of power supply (24 to 240V DC or AC single phase input voltages at 50 and 60 Hz). One single version to cover the whole range of operating times (10 to 400 seconds), with the possibility of different stroking times in the opening and the closing manoeuvres. One single version with interchangeable base plate for connection to various types of valves. As an option, Bluetooth TM technology allows your PDA or PC to have direct access to the F02 for non-intrusive operation, configuration and diagnostics. A look inside F02 basic design features: Mechanical connection to the valve: interchangeable base plate to suit various options foreseen on the Ordering Table (page 19). Shaft drive via insert bush to provide EN ISO 5211 dimensions and all the main standard dimensions of valve shafts. The drive insert meets all the different flange standards. Electric motor: one single innovative universal electric motor for each model, with suitable POWER SUPPLY MODULE to accept 24 to 240V DC or AC single phase input voltages at 50 and 60 Hz. Three-phase motors with power supply from 208 to 575 VAC (at 50 or 60 Hz) are available as option. Within the above power range, connect the F02 without taking care of the voltage available in your plant: the actuator will recognise it and adapt consequently. Internal thermostat: an overtemperature device to control the temperature inside the control enclosure is included as standard in the control group. Actuator service: the same actuator covers the operation of ON-OFF and MODULATING valves (with optional OM1 card). Compact and light design: the construction is very compact and balanced for easy installation and operation onto small valves without affecting stresses in the pipework and loads to the valve shafts. Reduced power consumption: thanks to a very low motor power consumption, it is possible to reduce the costs for electric power and also for the connection cables, since one single cable size is suitable for all actuator models. 4

6 ICON2000 technology: the electronic-mechanical design is based on the experience of ICON2000 advanced solutions with innovative features to provide maximum flexibility in terms of voltage supply, operation speeds and torque options. Actuator control, setting and diagnostics: each single function and parameter in the actuator control, setting and diagnostics is available in remote or locally. Local manual override: the basic feature includes a constantly engaged manual override, not rotating during motor operation, with manual input through the same handwheel. Torque and sizing: the F02 range comprises six different torque sizes, with inherent options for various voltages, motor supply and speeds, foreseen to cover up to Nm with operation time varying from 10 to 400 seconds. The nominal output torque value is constant along the entire stroke. Torque control: torque control is active in both directions with independent setting from 40% to 100% of nominal value. Torque setting by user-friendly rotary switches located inside the control enclosure. Actuator body and construction: the F02 body is in anodized die-cast aluminium, with epicyclical internal gearing in sintered alloy steel, lubricated with grease. The output drives are in cast iron. 5

7 Voltage ratings: 24 to 240V DC or AC single phase input voltages at 50 and 60 Hz; Tolerance of fluctuations: Voltage: +/- 10% continuous; Frequency: +/- 5%. (For 24 VDC/AC power supply please contact the factory) Working temperature: Waterproof version: The standard range is 25 C to % humidity; Special version is 40 C to % humidity; Special version 25 C to % humidity (Tropicalized); Explosionproof version: -20 C to +65 C (-13 F to +149 F) with 80% humidity -20 C to +65 C (-13 F to +149 F) with 100% humidity -40 C to +65 C (-40 F to +149 F) with 80% humidity 6 Electric motor: Special electric motor with innovative POWER SUPPLY MODULE to accept 24V to 240V DC and AC single phase input voltages at 50 and 60 Hz. (For 24 VDC/AC power supply please contact the factory) Overtemperature device to control the motor and internal temperature devices are included. Environmental protections: Water / dust-proof version: IP66/68M according to EN 60529; (IP66/NEMA types 4,4X&6 when labelled FM) NEMA 4/4X/6 according to NEMA ICS6 / NEMA 250. Standard explosion-proof version: ATEX EEx de IIB T5 (base version); ATEX EEx de ia IIB T4 (base version with additional OM3 module); FM rated as flameproof for Class I, Zone 1, Group IIB, T5; class II, III, Division 1, Groups E, F and G, T4. NEMA 7 and NEMA 9. Safety compliance: Machinery directive 2004/108/EC; Electromagnetic compatibility directive (EMC) 2004/108/EC and further amendments; Low voltage directive (LV) 2006/95/EC and further amendments by the application of EN Test Summary: Life tests Based on AWWA C (or other Standards) with minimum guaranteed cycles (Open- Close-Open) carried out with 80% of nominal torque along the stroke and stop with seating torque at 100% of nominal torque against the mechanical stopper at each end of the stroke. Vibration test F02 are tested as per IEC Appendix B (plant induced): frequencies from 1 to 500 Hz (in 3 axes) with 2.0g peak acceleration. Sweep cycles in each axis: 10. Seismic test F02 are tested in accordance with IEC Frequencies from 1 to 35 Hz (in 3 axes) with max 2.0g peak acceleration. Verification of structural integrity at 5g. Endurance of oscillogram: 30 seconds. Environmental test F02 are tested according to the following standards: IEC (cold) up to 40 C, IEC (dry heat) up to +70 C, IEC (damp heat) up to +40 C with 93% relative humidity. Salt spray test F02 external coating is tested for resistance to salt spray for 1,500 hours according to ASTM B117/IEC Noise test F02 are tested according to EN Noise level is less than 65 db (grade A) at 1m distance.

8 Painting: ESPC suitable for 1000 hours resistance to salt spray test according to ASTM B ASTM D test with 100% humidity is also available. Standard colour: Grey RAL Materials of construction of main parts: Parts Material Body and cover Anodised/ESPC die-cast aluminium alloy AC (EN 1076) Epicyclical gearing High-grade sintered alloy steel Motor reduction Reinforced acetalic resin as standard, or steel version Output drive Ductile cast iron (EN1563) grade GJS Interchangeable base plate Investment cast iron Manual worm shafts High-grade alloy steel Worm wheel Alloy steel O-ring NBR / Fluorosilicon suitable for ambient temperature range Lubrication Grease suitable for ambient temperature range Travel stops: Mechanical stops fixed on the base of the actuator to provide the following setting range: +/- 10 over travel in each rotation direction. (70 minimum/110 maximum angular stroke). Heater: Standard 10 Watt derived from the internal PCB with internal supply only. An internal thermostat will activate the heater when the temperature on the control enclosure drops below +10 C. Local indicator: Standard Window -type mechanical local position indicator on the top of the cover; Beacon -type is offered as option. Electronic controls: Internal drive to reverse the actuator rotation direction via 24VDC remote control signals with internal or external 24VDC power or with external 120VAC power. Push-to-Run 3 wires type (Open/Close/Common) remote control signals. Torque sensor in both directions, adjustable from 40% to 100% of nominal torque: torque adjustment by means of rotary graduated switches (10 steps). Patented contact-less POSITION SENSOR: position adjustment by means of a two-position selector switch. Output speed adjustment with ratio 1 to 9: speed adjustment by means of rotary graduated switches (10 steps). Different valve operating speed independently selectable for the opening and closing manoeuvres. n 4 SPST (NO/NC) latched-type contacts to be provided for fully Open/fully Closed remote indication. Output contact ratings: 240VAC/5 Amp; 30VDC/5 Amp; 120VDC/5 Amp. Position, torque, speed and output contacts configuration and settings are carried out directly on PCB, in the standard version, or non-intrusively via an optional PDA with Bluetooth TM protocol. Terminal enclosure: Terminal board enclosure in a separate compartment to accept power and controls incoming wiringwith 4 cable entries threaded as follows: N 4 cable entries 1 NPT: standard for the US Market N 4 cable entries M25x1,5: standard for the European Market Other options available by bushes or adapters. 7

9 OM1) I/O Additional module: Analog Position INPUT 4-20 ma or 0-10 VDC. Analog Position OUTPUT 4-20 ma or 0-10 VDC. Monitor Relay: loss of power, torque alarm, high temperature alarm, travel alarm, position sensor, hardware malfunction, and, when installed or selected, loss of input signal, local selector in Local, Bluetooth TM failure. Motor Running, or local selector position alarm (with OM3 installed) 4 additional SPST Output Contacts to be set independently at 10 points along the stroke. Contacts are configurable (make or brake). Optional Bluetooth TM interface. OM3) Local Interface with: Local/Remote Selector, OP/CL pushbuttons and 2 LEDs for local indication. Available in WP and EEX-ia version. 3 ph-supply modules alternative to the universal voltage standard: OM5) from 208 to 240 VAC (50-60 Hz). OM6) from 380 to 480 VAC (50-60 Hz). OM7) from 500 to 575 VAC (50-60 Hz). BUS Communication - Network Interfaces: BIFFI developed several optional network interface modules for the connection of F02 actuators to a BUS communication network. The connection to a bus system is very easy: simply plug in the interface card into the actuator enclosure, set all the parameters on the logic card or via non-intrusive devices through the configuration software from your Bluetooth TM PC/PDA. The following open Bus Protocols are available: OM9) OM11) Profibus DPV0/V1; Device Net; OM13) 3-WIRE MODULE: 120/240VAC, 3-wire control module for Open/Close. Optional modules selection criteria: please refer to ordering table, page 20 8

10 9

11 Rotary switches for easy actuator setting STANDARD An innovative motor operating with the whole range of voltages. STANDARD Accurate and adjustable torque control from 40% to 100% of nominal value. STANDARD Valve position detection with end of travel setting by rotary switches. STANDARD Interchangeable base plate for simple connection to all valve types. STANDARD Contact-less Position Detection adjustment by means of two-position sensors. STANDARD Variable speed control independently adjustable in either open or closed position. STANDARD Separate terminal block for easy and safe installation. 10 New sintered epicyclical internal gearing for a smooth, reliable operation

12 Separate terminal block for easy and safe installation Interchangeable base plate for simple connection to all types of valves 11

13 General Configuration with Base Card 12

14 (universal voltage) Size 063 Size 125 Size 250 Size Notes: 1) A= absorbed current (Amp) at nominal conditions (output torque 100%) 2) Max current (Amp) at stall conditions = 1,2xA 3) Current diagrams for VAC/1-phase supply Current diagrams for VDC supply 4) Power factor for VAC supply = 0,60 5) Peak current: max 8xIn 6) Peak current duration: less than 0,1 secs 13

15 (three-phase voltages) Size 063 Size 125 Size 250 Size Notes: 1) 3-phases supply 50 or 60Hz 2) A = absorbed current (Amp) at nominal conditions with output torque set at 100% 3) Power factor = 1 approx. 4) Starting current peak less than 10 microsecs

16 * W= Nr. 4 cable entries M25x1.5 acc. to ISO 724/965-1 (others available as special versions) X= Space for cover removal F= ISO 5211 Standard flange (others available) F02 Series Overall Dimensions - Base Unit Model A B H a1 b1 b2 b3 c d e h1 h2 h3 ØV x F (1) F07 F10 F12 F12 F16 Weight Kg 7,50 9,50 16,5 18,0 26,0 * Note: ISO 5211 flanges follow standard dimensions of the larger type for each actuator size; reduced bolting version is provided on the same flange as a standard (see details, page 17). 15

17 F02 Series Overall Dimensions with Optional Modules Model A A1 a1 a11 H H1 X X1 Weight (4) Weight (5) (Kg) (Kg) ,50 8, ,50 10, ,5 16, ,0 17, ,0 26,5 Notes: 1. This table is referred to the Base Unit version plus Additional Options: Local Interface and/or BEACON type Indicator 2. Dimensions with additional index 1 include the Additional Option Module/Modules 3. Other dimensions as per base unit version 4. Weight with BEACON Option Module 5. Weight with Local Interface with/without BEACON Option Module. 16

18 * * With optional local interface module W= Nr. 4 cable entries M25x1.5 acc. to ISO 724/965-1 (others available as special versions) X= Space for cover removal F= ISO 5211 Standard flange (others available, see details, page 20) F02 Series Overall Dimensions Model A A1 B H a1 a11 b1 b2 b3 c d e h1 h2 h3 ØV x F F10-F14 F12-F16 Weight Kg 45,0 46,5 17

19 F02 Series - Stroking Time Selection Table Model Nominal Operating Time (secs 90 ) at selected step (1) Torque(Nm) (1) times are guaranteed with a tolerance of 10% on the 90 stroke Valve Attachments - EN ISO 5211 Standard Insert drive dimensions (mm) Insert drive dimensions (mm) EN ISO 5211 Style Index Style Index Model Flange Square l (1) 5 X 14 X 15 Flat Key X 14 X 15 l (1) F05-F D4 14xD20 - E F07-F D5 22xD30 - E F07-F10-F D5 22xD30 - E F10-F D6 - D35 E F10-F D F12-F DA - D50 E F10-F D F12-F DA - D50 E9 80 (1) Insert length (mm) Valve Attachments - K-type Non-ISO flanges Insert drive dimensions (mm) K Style Index Model Flange Flat Key X 14 X 15 l (1) xD19 - U D28.58 U D28.58 U D41.28 UA D47.63 UC D47.63 UC 108 (1) Insert length (mm) Insert Drive - Non-Standard 5 MODEL Ø d7 max Ø dx max SQ max

20 X 1 X 2 X 3 -X 4 X 5 X 6 -X 7 X 8 - X 9 X 10 - X 11 X 12 - X 13 - X 14 X 15 1) Product (3 digits) BPD = ISO 5211 with double star insert BPE = ISO 5211 with flat or key insert BPU = Non-ISO flange 2) Models (3 digits) 063 = Model B = Model 063 with BEACON 125 = Model B = Model 125 with BEACON 250 = Model B = Model 250 with BEACON 500 = Model B = Model 500 with BEACON 1K0 = Model KB = Model 1000 with BEACON 2K0 = Model KB = Model 2000 with BEACON 3) Voltage (2 digits) UV = Universal Voltage from 24 to 240 Vdc/Vac-1Ph 31 = 3-Phases Voltage from 208 to 240 Vac (50/60 Hz) 32 = 3-Phases Voltage from 380 to 480 Vac (50/60 Hz) 33 = 3-Phases Voltage from 500 to 575 Vac (50/60 Hz) 4) Speed/Duty (2 digits) PA = Standard Speed range and Standard Duties for models 063 to 500 PB = Standard Speed range and Standard Duties for model 1000 PC = Standard Speed range and Standard Duties for model ) Options (2 digits) X 11 X 12 = Refer to the Option Modules Selection Table (page 20) 6) Approvals/Protections (1 digit) 1 = (N/A) 2 = Standard protection NEMA 4/4X/6 (IP66/68M) T amb from 25 C to +70 C 3 = Standard protection NEMA 4/4X/6 (IP66/68M) T amb from 40 C to +70 C 4 = ATEX EEx-de + Standard protection NEMA 4/4X/6 (IP66/68M) T amb from 25 C to +65 C 5 = Standard protection NEMA 4/4X/6 (IP66/68M) T amb from 25 C to +70 C tropicalised 6 = (N/A) 7 = (N/A) 8 = ATEX EEx-de + Standard protection NEMA 4/4X/6 (IP66/68M) T amb from 20 C to +65 C tropicalised 9 = ATEX EEx-de + Standard protection NEMA 4/4X/6 (IP66/68M) T amb from 40 C to +65 C 7) Flange/Insert (2 digits) Flange/Models / /2000 ISO 5211 (BPD) D4 D5 D5 D6 D7 (F10-F14) DA (F12-F16) ISO 5211 (BPE) E3 E5 E5 E6 N/A E9 (F12-F16) NON-ISO (BPU) U4 U8 U8 UA UC N/A Without F1/Insert

21 Optional Modules selection table Optional Module (1) OM1 OM1 OM1 OM1 OM3 OM9 OM9 OM11 OM11 OM13 (*) OM1 I/O additional module OM3 Local interface Bluetooth component (2) OM9 PDP V0/V1 OM10 FF OM11 Device Net OM13 3-wires module Code(3) X 11 X 12 P1 PA P6 P7 P3 5P 6P 6D 5D PG Notes: (1) All modules except OM13 are available for both Universal Voltage and 3-Ph voltage versions. (2) Bluetooth component is integrated in the OM1, OM9 and OM11 card: not available for integration by Local Organizations, as a stand alone unit. show the combination of modules specified in the Oracle code by digits X 11 X 12. (*) Not available with 3-phase supply modules OM5, 6 and 7. 20

22 For any further information you may require please contact Biffi Sales office; tel , fax , Norwegian distributor: Haakon Ellingsen AS Årenga 8, N-1340 Skui P.O. Box 184, N-1309 Rud Phone Fax post@ellingsen.biz 21