1 Installation Instruction for '84-'89 Nissan 300ZX High Performance Intercooler System (Part No )
3 Routing of the Intercooler Pipe It is necessary to follow the exact sequence of the installation of the tubing, otherwise it may increase the difficulty and installation time. Proceed as follows: To provide clearance for installing the pipes, it is necessary to remove the top heat shield and the bottom heat shield which are situated to the outside of and behind the turbocharger. A. Slide number #6 tube in from the bottom, hooking it up over the top of the radiator. The straight end goes toward the intercooler, the curved end goes topside. B. Connect #6 tube to #5 tube with hose and clamps and mount to the bottom of the intercooler with reducing hose and clamps. C. Assemble #4 tube to AE (aluminum elbow) and slide them up from the bottom and hook over the top of the radiator. Connect AE to the intercooler with reducing hose and clamps. Orient the hose clamps so that they are pointing forward so that they can be tightened with a small ratchet. (Do not fully tighten at this time). D. Install #7 tube by slipping it down beside the radiator shroud, and pushing it toward the rear beneath the air flow meter and connect it to the #6 tube with the hose and clamps provided. E. Install #8 tube by sliding it down into the engine compartment between the shock tower and the engine and behind the air conditioning compressor. Connect it to #7 tube with the hose and clamps provided. F. Install #1 tube into position and connect it to the turbocharger outlet using the clamps and reducer hose provided. G. Connect #2 tube to #1 tube. H. Install the #3 tube over the radiator shroud and connect it between the #2 and #4 tubes. Position clamps with screws on top so they can be easily tightened. I. Now connect #8 tube to #7 tube and install the remaining #9 tube between the #8 tube and the throttle body. J. Connect the existing PCV and Idle by-pass hoses. K. Adjust the tubes for proper clearance; make certain there is sufficient clearance between the air conditioning pulley and the #2 tube. Tighten all clamps and inspect your work.
4 Page ii DCB (06/14/02 12:19 AM) Version 1.0
5 Page iii Table of Contents 1. TOOLS REQUIRED INSTALLATION PREPARATION REMOVAL OF STOCK COMPONENTS REMOVAL AND OR REPOSITIONING OF THE FRONT MOUNTED COOLING FAN Reinstallation of fan motor For the early style model For the late style model Fan Rewiring TOP RADIATOR BAFFLE MODIFICATION INSTALLATION OF INTERCOOLER ROUTING OF THE INTERCOOLER PIPE PROCEED AS FOLLOWS: REMOUNTING OF IGNITION COIL INSTALLATION OF BOOST PRESSURE MAXIMIZER BOOST PRESSURE ENRICHMENT OPERATION AND PERFORMANCE TUNING TIPS...9 List of Figures FIGURE 1 WASTEGATE ACTUATOR AND BOOST PRESSURE ENRICHMENT SCHEMATIC...10 FIGURE 2 INTERCOOLER PARTS 1 THRU FIGURE 3 INTERCOOLER PARTS FIGURE 4 INTERCOOLER PARTS FIGURE 5 INTERCOOLER PARTS FIGURE 6 INTERCOOLER PARTS FIGURE 7 PARTS FIGURE 8 PART FIGURE 9 PARTS FIGURE 10 PARTS FIGURE 11 PARTS
6 Page 1 1. TOOLS REQUIRED 1.) Standard mechanic hand tools 2.) Wrenches (SAE and Metric) 3.) Sockets and Ratchets (SAE and Metric) 4.) Floor jack and jack stands IMPORTANT NOTE: Due to the design of this vehicle, and the intercooler system, it necessitates ten separate intercooler pipes and an equal number of hoses and clamps. All tubes are beaded for hose retention and high quality clamps are provided. However, extra care should be given to see that the hoses are equal distant on each end of the tube, and that the clamp is properly positioned behind the hose bead on the tube. 2. Installation Preparation 2.1 Removal of Stock Components Remove the following stock components: a.) Compressor discharge pipe from the turbocharger to the throttle body b.) Complete air cleaner assembly. c.) Injection blower mounted on the left front fender well. d.) Ignition coil solenoid valve in left inner fender well. e.) Pressure transducer in left inner fender well. f.) Headlight washer tank assembly. g.) Plastic tray on the bottom of the vehicle. h.) 3" I. D. convoluted, curved rubber tube at the air meter end NOTE: The solenoid valve, ignition coil and pressure transducer will be remounted, utilizing brackets provided.
7 Page Removal and or Repositioning of the Front Mounted Cooling Fan IMPORTANT NOTE: Since this fan occupies that space which will be utilized by the intercooler, it is necessary to relocated it to the back side of the radiator, inside the radiator shroud. These vehicles are equipped with two styles of fan assemblies and brackets and details are provided for the relocation of both types. However, this relocation procedure is some what tedious and time consuming and, unless you live in a geographical area where ambient temperatures exceed 85 F during the summer, or you are going to be pulling a trailer with your vehicle, it may not be necessary to utilize the fan, it can simply be removed. This fan only operates when coolant temperature is above 212 F, which generally can only be obtained when the vehicle is shut down in hot weather, and during the resultant heat sock period, when the temperature may reach 212 F. In this event, the fan will not run until the engine is started and generally runs only for a minute or so and then shuts off. Under our test conditions, in ambient temperature as high as 98 F, we have been unable to get the fan to come on in stop and go traffic or any type of normal driving situations. Therefore make the decision to install the fan or not, and if you decide to install the fan, proceed as follows Reinstallation of fan motor First, identify which model of fan you have in your vehicle. The small or early style fan, is identified with a sticker IHON Radiator Company, LTD. Japan, number A It has white colored plastic fan blades. The late style is identified as being manufactured in Japan by Mitsuba, and has black plastic fan blades For the early style model a) Remove the nut holding the white plastic fan blades in place, and reverse the fan blades, as the motor is going to be operated in the opposite direction. b) Unbolt the fan assembly from the cross brace mounts, install the four 1"X1" foam rubber pads on the four flat mounting areas of the fan, and slide it down between the shroud and the radiator fan. Push forward and up and orient so that the wire is on the bottom side of the fan.
8 Page 3 c) Before installing the nylon retaining devices, preload the fan downward against the radiator and make certain that there is sufficient space between the fan blades and the radiator. If not, it will be necessary to add washers between the sponge rubber material and the fan frame. d) Glue in place as required. e) Re-insert the fan between the shroud and the engine fan and hold in place by pushing the nylon attaching devices through the sponge, the radiator and the condenser core and retaining with the locks provided. Note that these locks are one time type of installation, and you must be sure that the fan is correctly positioned before the locks are slid into place. f) Drill a small hole in the bottom of the fan shroud and, with a small tie strap, retain the fan wire so that it cannot come in contact with the engine fan For the late style model a) If you have the large type, or later fan manufactured by Mitsuba, with the black plastic blades, remove the blade retaining nut, and not it will be necessary to grind off some small ribs on the back of the fan blade and some small protrusion on the motor so that when the fan is lifted off and reversed, an held down with a nut, it will freely turn. b) Cut the four round mounting rods shown in the photo and mount the fan to the brackets, using four small hose clamps. c) The fan is installed into position using the same procedure as used on the early style fan shown above. Be sure and retain the fan motor wire so that it cannot come in contact with the engine fan Fan Rewiring Since the above fans will now have to rotate in the opposite direction, to suck air rather than blow air, it is necessary to reverse the polarity of the current going to the fan motor, and it is necessary to extend the wires. a.) This is done by cutting the wires of the chassis end of the connector approximately three inches (3") from the connector. b.) Extend them with the two pieces of 22" long wire provided, and re-route the wire back underneath the radiator cross member and plug into the fan connector. c.) Make absolutely certain that you have reversed the wires, or the fan will run in the opposite direction.
9 Page 4 d.) When you are confident that the fan is installed correctly, reinstall the radiator shroud and re-attach with the three spring clips and top bolt.
10 Page 5 3. Top Radiator Baffle Modification Before the intercooler can be mounted and the intercooler piping routed, check your vehicle to see if it has a sheet metal and rubber baffle between the top edge of the radiator and the body. a.) This is done by getting beneath the vehicle and viewing upward to the top edge of the condenser and the radiator. If you find a formed, sheet metal shield, approximately 2" wide, which goes completely across the top of the radiator, with a rubber flap stapled to it, it will be necessary to remove this to secure space for routing of the pipes. Unfortunately, Nissan has made this an extremely difficult thing to remove, as the manual indicated the radiator must be removed. However, it can be removed and modified without removing the radiator, if patience is utilized. b.) Another solution is to take tin snips and cut it out of the way so that an area measuring from the left side of the condenser toward the center of the car is left clear approximately 7" wide. If you elect to cut it out of the way while on the vehicle, be extremely careful when installing the tubes. c.) If you elect to remove it and modify it, drain the water from the vehicle using the petcock in the bottom of the radiator. Remove the top radiator hose, remove the two top radiator retaining bolts. These bolts are small 6mm with a 10mm head and are extremely difficult 'to get to. However, by utilizing patience and a small Snap-On type ¼ drive universal ratchet, end wrench etc, they can be removed. d.) Once they have been removed, work the shield out from the bottom of the vehicle and modify as shown in the photograph. Installation is a bit simpler, as we have provided two 10/32 X 3/4" bolts and lock nuts, which can be inserted through the threaded holes and the bolts tightened from the bottom. e.) Reinstall the top radiator hose and re-fill with water.
11 Page 6 4. Installation of Intercooler In order to provide clearance for the intercooler on vehicles so equipped, it will be necessary to remove the ambient temperature sensor, which is mounted on the left bottom part of the bumper. a.) Remove the bracket and disconnect the sensor bracket from the large bracket. This can be mounted by drilling a hole in the plastic spoiler, or held in place with a plastic tie strap. b.) Located the proper brackets, which are attached to the bottom of the front bumper, by removing the four existing Phillips head screws and attaching the brackets with 4 larger hex head sheet metal screws. (Do not fully tighten at this time). c.) Slide the intercooler into position and insert the two top 7/16-18 X 3/4" long bolts to hold the intercooler into position. Move the brackets around until you secure correct alignment. d.) Mount the bottom tab bracket to the intercooler up so that the edge of the bracket is approximately level with the bottom of the radiator cross-member. e.) Mark and drill and attach with a 1/4" bolt and locknut. Tighten all brackets.
12 Page 7 5. Routing of the Intercooler Pipe To provide clearance for installing the pipes, it is necessary to remove the top heat shield and the bottom heat shield which are situated to the outside of and behind the turbocharger. To secure simple installation, it is necessary to follow the exact sequence of the installation of the piping, otherwise it may be difficult. 5.1 Proceed as follows: a.) Slide number 6 tube in from the bottom, hooking up over the top of the radiator. The straight end goes toward the intercooler. The curved end goes topside. b.) Connect #6 tube to #5 tube with hose and clamps and mount to the bottom of the intercooler with reducing hose and clamps. c.) Now assemble pipe number 4 to the cast aluminum elbow, with the short end of the elbow toward the intercooler. Slide this up from the bottom and hook over the top of the radiator. Connect to the intercooler with reducing hose and clamps. Orient the hose clamps so that they are pointing forward so that they can be tightened with a small ratchet. (Do not fully tighten at this time). d.) Now, locate number 7 pipe and install by slipping down beside the radiator shroud, and pushing toward the rear beneath the air flow meter. Connect to pipe number 6 with hose and clamps provided. e.) Install pipe number 8 by sliding down in the engine compartment between the spring tower and the engine and behind the air conditioning compressor. Negotiate forward and connect with hose and clamps to pipe number 7. f.) Slide pipe number 1 into position by inserting down and up behind the airconditioning compressor, and attach with clamps and reducer hose provided. g.) Attach number 2 tube to number 1 tube and join number 2 to number 4 by installing number 3 tube over the radiator shroud. Position clamps with screws on top so they can be easily tightened. h.) Now slide number 8 pipe into number 7 pipe and install the remaining number 9 pipe, which is the curved 2 1/2" pipe into the throttle body and connect to number 8 with reducing hose provided. i.) Connect the existing PCV and Idle by-pass hoses.
13 Page 8 j.) Check all pipes for proper clearance, and make certain there is sufficient clearance between the air conditioning pulley and the number 2 pipe. Orient pipes as required, and then go through system and tighten and check all clamps. k.) After the pipes are all properly installed, positioned, and tightened modify the heat shields as shown in the photograph and re-install. l.) Re-install the 3" diameter curved and convoluted hose to the air meter and install 3" diameter curved pipe and air cleaner assembly. 6. Remounting of Ignition Coil a.) Locate the special bracket, dismount the ignition coil from the existing bracket and remount the solenoid valve, power transistor, and the ignition coil to the new bracket (See Photograph). b.) Mount the transducer to the mounting tab and remount in engine compartment in the position shown in the photo. 7. Installation of Boost Pressure Maximizer a.) From beneath the car locate the hose that connects at two points into the turbocharger compressor housing, and routes to the boost pressure actuator. Remove it at the boost pressure actuator end, and plug this hose. b.) Attach a 17" long piece of the 1/4" hose provided to the boost pressure actuator and route up to the topside of the engine compartment. c.) With a tie strap provided, retain the hose that it will not come in contact with the hot exhaust housing. d.) Install the special plastic restrictor tee provided in the end of this hose, and connect the other end of the tee to the fitting on the number 9 pipe, the pipe that attaches to the throttle body, see drawing which illustrates this hook-up. With the restrictor installed as shown, boost pressure will go up to approximately 9 psi maximum, and then, as engine speed increases, drop down to approximately 6 psi maximum.
14 Page 9 8. Boost Pressure Enrichment a.) Mount the pressure switch and solenoid valve assembly on the firewall, as shown in the photograph. b.) Connect one terminal of the solenoid valve to the red and white striped wire in the side of the windshield washer motor nearest to the engine. c.) Utilize a piggyback terminal provided. d.) Connect the other terminal of the solenoid valve to the pressure switch. Remove the plug located approximately 5" behind the throttle valve assembly in the top of the intake manifold and install the fittings provided for this installation. e.) The 5/32" hose connections to the solenoid valve should be as indicated in the photo. This device applies charge pressure to the fuel pressure regulator, during boost pressure operation for the denser charge created by the intercooler. For optimum performance, it is essential that the boost pressure enrichment and boost pressure maximum operate properly. f.) To check the Boost Pressure Enrichment System, start the engine and let it idle. Remove the small vacuum hose that goes to the fitting on the top of the fuel pressure regulator (round object in front of the intake manifold). Hold your finger over the hose and check to see that vacuum is present. With a screwdriver short the switch out or trigger the switch with a hand air pressure source. Whenever the switch is triggered and the solenoid valve switches, the vacuum signal should go away. Under road boost pressure conditions, higher boost pressure at the turbo is diverted to the pressure regulator. Since there is a pressure loss through the intercooler, the normal pressure pick up signal reduces through the intercooler, the normal pressure pick up signal reduces the injector fuel pressure, therefore, by diverting pressure from directly at the turbocharger, fuel flow is increased approximately 15%. 9. Operation and Performance Tuning Tips When operating properly, this system will yield reductions in charge temperature of up to 135 F. This alone increases performance, and when coupled with increased boost pressure, created by the Boost Pressure Maximizer System and the Boost Pressure Enrichment, performance is greatly enhanced. In the event your vehicle is not equipped with a boost gauge, Spearco offers a 2 1/16" diameter Turbo Boost gauge, which will allow you to monitor boost pressure operation.
15 Page 10 For drag racing applications, if you choose to operate the boost at higher than 9 psi, it will be necessary to remove the pop off valve installed in the right front side of the intake manifold, as it will relieve boost pressure at over 9 psi. In conjunction with additional boost pressure, for off road or drag racing applications, advance the timing 5 to optimize performance. Figure 1 Wastegate actuator and boost pressure enrichment schematic
16 Page 11 Figure 2 Intercooler Parts 1 thru 8 1. Intercooler Assembly 2. Top mounting brackets, right and left hand. 3. Bottom mounting bracket 4. Existing fan motor wire, which is extended to back of radiator deg cast aluminum elbow 6. Tube #6 7. Tube #5 8. Remount temp.sensor as shown
17 Page 12 Figure 3 Intercooler Parts 9 9. Top radiator baffle remove from vehicle, modify as shown Figure 4 Intercooler Parts Tube #9 2-1/2" O.D. 11. Tube # " O.D. Air Cleaner Tube 13. Tube #3 14. Solenoid valve/pressure switch assembly. See detail photo /8"street ell & 1/4"hose barb for wastegate connection. See detail
18 Page 13 Figure 5 Intercooler Parts Tube #3 17. Tube #6 18. Position of remounted pressure transducer. 19. Relocate burglar alarm switch and hold with outboard screw only
19 Page 14 Figure 6 Intercooler Parts Extend existing fan wires, change polarity and route to reposition fan connector as shown. 21. Drill hole in bottom of fan shroud and secure fan wire as shown. 22. Disconnect headlight washer pump wiring harness.
20 Page 15 Figure 7 Parts Remount ignition coil, solenoid & power transistor as shown. See detail photo 24. Tube #1
21 Page 16 Figure 8 Part Cut off tab or bend down as shown
22 Page 17 Figure 9 Parts Secure fan wire to fan shroud. Drill a hole & install tie strap. 27. Mitsuba (late type) fan motor assembly set of mounting hardware including 6 1" x 1" sponge rubber pads, nylon rods and nylon rod locks. 29. Fan mounting brackets right & left Cut off fan bracket as shown & mount to fan with hose clamps provided.
23 Page 18 Figure 10 Parts Ignition coil and solenoid bracket. 31. Pressure transducer bracket. Mount ignition coil & pressure transducer per detail. Figure 11 Parts Mount pressure switch & solenoid to firewall as shown by drilling & mounting with sheet metal screws. See drawing for alternate style.
24 Page Pressure hose - throttle body to switch. 34. To connection on #1 Tube. 35. To fuel pressure regulator via solenoid 36. Intake manifold downstream of throttle (stock, original pressure tap for pressure regulator). See schematic. 37. Connect to bottom wire on windshield wiper connector as shown. Connection is 12 volt/hot on run only. 38. Pressure connection for pressure switch 1/8"street ell, 1/4" bushing and 5/32" hose barb
Installation Instruction for '84-'89 Nissan 300ZX High Performance Intercooler System (Part No. 2-124) Page ii DCB (06/14/02 12:19 AM) Version 1.0 Page iii Table of Contents 1. TOOLS REQUIRED...1 2. INSTALLATION
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Congratulations on your new upgraded piping and intercooler kit, this kit has proven to provide the lowest intake air temps to date on our
INSTRUCTIONS INTERCOOLER UPGRADE BMW E82 135i 2008- Parts Included: - Intercooler - Left and right side pipes with hoses - 3 Silicone Hoses ( 2.5 x 3 ) - 1 Silicone Hose 90degree 2.5 elbow - 8 Hoseclamps
FRONT MOUNT INTERCOOLER 2008-13 STI 2014-04- 08 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
Before Commencing Installation Verify that you have all necessary tools as listed. Clean all air ducting prior to commencing installation. The sequence of installation of each part is very important. It
2003 Ford Expedition 4.6L& 5.4L We encourage you to read this manual thoroughly before you begin work, and perform the following: 1. A quick parts check to make certain your kit is complete. If you discover
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: email@example.com These instructions are based on a vehicle with an OEM turbocharger
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
Owner smanual with Installation Instructions Banks Techni-Cooler Intercooler System 1999-2006 4.0L I-6 Jeep Wrangler THIS MANUAL IS FOR USE WITH SYSTEMS: 1999-2004 WRANGLER - SYSTEM 25400, 2005-2006 WRANGLER
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
Subaru 2004+ Legacy GT & Outback XT For JDM 2.0 twinscroll turbo and USDM 2.5 turbo models Front Mount Intercooler Fitting Instructions PN# LEG-1348-000 You are now the proud owner of a highly tested and
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge
This write up covers removing and replacing the radiator on a 97 855 GLT wagon with light pressure turbo and automatic transmission. This car has 162K miles. The radiator, which was original, developed
INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder
PARTS LIST AND PARTS INCLUDED 1PC MISHIMOTO INTERCOOLER 2PC SILICONE BOOTS WITH DURACORE TECHNOLOGY 4PC CONSTANT-TENSION T-BOLT CLAMPS 2PC ALUMINUM SPACERS MOUNTING HARDWARE CAUTION Never work on the cooling
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only. The purpose of this guide is to serve as a reference for use when
1985-86 32v Porsche 928 Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger kit at this price relies
90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
WWW.JEEPAIR.COM 1996-1998 Jeep Wrangler TJ Complete Air Conditioning System Slide Control Head Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
PARTS LIST AND INSTALLATION GUIDE PARTS LIST 2 PC APPLICATION-SPECIFIC MOUNTING BRACKETS 2 PC BLACK, ANODIZED 6061 ALUMINUM CATCH CANS 4 PC SILICONE HOSES 4 PC PLASTIC BARBED FITTINGS 4 PC WORM-GEAR CLAMPS
with Installation Instructions Owner smanual Banks High-Flow Boost Tubes Stock Fitment 2011-2016 Chevy/GMC Turbo-Diesel Pickup Trucks THIS MANUAL IS FOR USE WITH PART NUMBER 25993 Gale Banks Engineering
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: firstname.lastname@example.org These instructions are based on a vehicle with an OEM turbocharger
96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove
2015 Corvette Supercharger System Instructions These instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharging system. Please be sure to use all safety equipment
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
V1 Truck Manifold Turbo Kit for 98-02 F-body Prep: -Remove all A/C Components, Alternator and brackets, tensioner, front bumper, front bumper foam, and front bumper support. Remove radiator and cooling
#F9378 Installation Instructions 1998-2000 Ford Ranger 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
INSTALLATION INSTRUCTIONS Dual Catch Can Kit 02-14 Subaru Turbo and 2015+ STi Document# 19-0099 Support: email@example.com This document covers the installation of a Radium dual catch can kit for the
TM www.jeepair.com 1999 Jeep Wrangler 4.0 Liter TJ 1999-2001 Jeep Wrangler 2.5 Liter TJ Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The Jeep kit
INSTRUCTION INTERCOOLER UPGRADE BMW E92 335i 2007-2011 Parts Included: - Intercooler - Shroud with seals - Left and right side pipes with hoses - 1 Silicone Hoses ( 2.5 x 3 ) - 2 Silicone Hose 45 degree
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-721C 2011-2013 MINI Cooper S L4-1.6L SEE NOTE* 2011-2013 MINI Clubman S L4-1.6L SEE NOTE* 2011-2013 MINI Cooper
Edelbrock 5.0L Mustang GT Supercharger Part #1588 & 1589 INTRODUCTION Edelbrock 5.0L Ford Supercharger System Thank you for purchasing the Edelbrock 5.0L Ford Supercharger System for the Mustang GT. The
PARTS LIST AND PARTS INCLUDED 3PC APPLICATION-SPECIFIC MOUNTING BRACKETS & SPACER 1PC 19-ROW OIL COOLER 1PC 4 ', X 1'' BRAIDED HOSE W/90-10AN FITTINGS 1PC 3'' X 2.5 '' BRAIDED HOSE W/45 AND 90-10AN FITTINGS
Corvette Stage X Twin Turbo Installation Please read the entire instructions as we ve made many changes. Disconnect battery. Remove plastic fuel rail covers over the valve cover. Remove Air Box in front
4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
PARTS LIST AND PARTS LIST 1PC BAR-AND-PLATE INTERCOOLER 1PC INTERCOOLER MOUNTING BRACKET 1PC CHARGE-PIPE ASSEMBLY 1PC AIR DIVERTER WITH ATTACHED RUBBER GASKETS 1PC CHARGE-PIPE-TO-INTERCOOLER HOSE INSTALLATION
PARTS LIST AND PARTS LIST 1PC MISHIMOTO INTERCOOLER 1PC M6 X 1.0 X 20MM FLANGE BOLT 1PC M4 X 0.7 X 12MM BUTTON-HEAD BOLT 1PC M4 LOCK WASHER 1PC MAP SENSOR O-RING 2. Remove the eight pop clips that hold
TOP FEED FUEL RAIL KIT for 2002-14 WRX Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
Exhaust Heat Shield Instructions ND 2016 + Thank you for purchasing the Track Dog Racing Exhaust Heat Shield for the 2016 to Present Mazda MX-5. Our TDR Heat Shield is designed to help maintain lower temperatures
Air Oil Separator for 2015+ WRX 2018-06-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
Edelbrock E-Force Supercharger Part #1538: 2009-2014 Dodge 1500 Truck 5.7L V8 HEMI 2009-14 Dodge 5.7L Hemi 1500 Truck INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the 2009-15
P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
Hellion Power Systems 03-04 Mustang Cobra Kit Instructions NECESSARY PARTS REQUIRED FOR INSTALLATION Necessary: 03-04 Cobra hellion Kit ONLY 99-01 Alternator #YR3210346AA Alternator Bracket #XR3Z-10153-AB
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
Directions for Installation of ECS Paxton Supercharger Kit Disconnect battery Remove stock serpentine belt Remove stock belt tensioner, save the 2 bolts for later use on supercharger bracket Remove alternator
INSTALLATION INSTRUCTIONS DUAL OIL CATCH CAN KIT SUBARU WRX FA20F ENGINE Document: 19-0135 Support: firstname.lastname@example.org This dual catch can kit installs in the right-hand side of the engine bay and intercepts
HASPORT PERFORMANCE Installation Instructions For: Part Number EFK1 K-series Mount Kit for 1988 1991 Civic and CR-X HASPORT PERFORMANCE Inc. 2849 S. 44 th St. Phoenix, AZ 85040 Phone: (602) 470-0065 Fax:
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE INSTALLATION INSTRUCTIONS Time will be saved if these instructions are read PRIOR to installation of the intercooler package. A. ITEMS TO
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components
Owner smanual with Installation Instructions Banks Techni-Cooler Intercooler Assembly 2003-2007 Ford Power Stroke 6.0L Turbo-Diesel F250/F350/F450/F550 Trucks & Excursions THIS MANUAL IS FOR USE WITH SYSTEMs