Dual Fire Capacitor Discharge Ignition
|
|
- Sherman Jordan
- 6 years ago
- Views:
Transcription
1 Dual Fire Capacitor Discharge Ignition Page 1
2 Dual Fire CDI Instruction Manual VERSION 1.0 Warning Please ensure all power supplies are disconnected before commencing work. This product produces high voltages. Careless use of this product can cause harmful and fatal injury to humans. DO NOT handle the red/white or red/yellow wires if the unit is connected to power. Incorrect set-up of this product can also lead to engine and product damage. Any damage caused due to incorrect set-up will not be regarded as repairable under warranty. Any unused wires must be insulated to prevent them from short-circuiting. The power supply to this CDI must be fused with a fuse rated not more than 20 amp. Failure to follow all the warnings and instructions in this manual may lead to product and engine damage and will also void your warranty. Page 2
3 LIMITED WARRANTY EMS Computers Pty Ltd warrants the Dual Fire Capacitor Discharge system to be free from defects in material or workmanship for a period of 90 days from the date of purchase. Proof of purchase must be provided indicating that the product is within the warranty period in order to receive warranty service. Removing the serial number affixed to the product will void any warranty. If the Dual Fire Capacitor Discharge system is found to be defective within the rules mentioned above it will be replaced or repaired at no extra charge this constitutes the sole liability of EMS Computers. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representations, either expressed or implied, including any implied warranty of merchantability or fitness. In no event shall EMS Computers, be liable for special or consequential damages. Page 3
4 CONTENTS Installation 5 Connecting to Power 5 Mounting 5 Ignition Leads and Sparkplugs 5 How to wire the input channels 6 How to wire the output channels 6 How to fire 2 channels together 7 How to wire the output channels for a rotary 7 How to discharge 2 capacitors into one coil 7 Overheat protection 7 Tacho output (brown/blue wire) 7 Operation modes 8 Rotary Mode (brown/yellow wire) 8 Trigger Edge (brown/white wire) 8 Power Select (brown/pink wire) 8 Mode Select (brown wire) 8 Specifications 9 Power Specifications Table 9 EMS Computers Dual Fire Pin Description 10 Drawings 11 Socket view 11 4 cylinder example 12 6 cylinder example 13 8 cylinder example 14 Rotary 3 coil example 15 Rotary 4 coil example 16 Page 4
5 Installation Connecting to Power The Dual Fire CDI has 2 red power wires and 2 black ground wires. These wires are joined together internally and should also be joined together at termination. The reason for using dual wires is to ensure maximum current flow. However, the amount of current draw is proportional to the number of cylinders and maximum RPM. Therefore, it may not be necessary to use dual wires if you have a 4 cylinder and not running the CDI in drag racing mode. As a safety feature the Dual Fire CDI does not keep power onto the positive side of the coils if the engine is not running. The system will charge the capacitors on initial power-up. If the engine is not started immediately the capacitors are discharged again. Once the system detects a trigger signal on any input channel it will immediately charge the capacitors and fire the next output channel in sequence. Mounting Do not mount the unit where it will be exposed to water or excessive moisture. Select a location away from excessive heat and in a location that does not obstruct air flow around the CDI. Use soft rubber mounts if the CDI will be subjected to strong vibration or the vehicle is has stiff suspension. Ignition Leads and Sparkplugs Do not use metal wire ignition leads because these will cause electrical interference that may effect the operation of the CDI or other electronic devices in the vehicle. Do not use carbon suppressed ignition leads because the carbon core is NOT capable of conducting the high energy levels of the CDI. Try to use ignition leads with a spiral wound inductively suppressed metal core. Not all brands of carbon resistor spark plugs are able to stand the high-energy output of a CDI system. NGK Q series and Champion Z series sparkplugs are specifically made for high-energy applications. IGNITION COILS AND THE CDI SYSTEM MAY BE DAMAGED INTERNALLY IF FIRED WITHOUT A HIGH VOLTAGE RETURN PATH. YOU MUST ENSURE THAT THE SPARKPLUGS ARE GROUNDED BEFORE FIRING. Page 5
6 How to wire the input channels The EMS Dual Fire CDI is essentially 2 CDI systems in one. The odd numbered channels use one discharge capacitor and the even numbered channels use another. In order to get the maximum benefit from the EMS Dual fire system you must wire the input and output channels in an odd-even sequence. To achieve this, connect the first cylinder to fire to channel 1, the second cylinder to fire to channel 2, the third to fire to channel 3 and so on. EG: If the firing order is 1,5,3,6,2,4 then connect the ECU ignition outputs to the CDI input channels according to the table below. Cylinder Firing CDI Input Channel Wire Colour Order from ECU 1 1 Pink 5 2 Orange 3 3 Grey 6 4 Yellow 2 5 White 4 6 Blue How to wire the output channels This also applies to the CDI output channels. The CDI channel outputs must be connected to the negative side of each coil. The positive side of the coils share two common voltage output banks, one for odd channels and one for even channels. The red/white wires must be connected to the positive side of the coils for all odd numbered channel outputs and the red/yellow wires must be connected to the positive side of the coils for each even numbered channel outputs. The red/white wires are connected together internally and the red/yellow wires are also connected together internally. EG: If the CDI input channels are connected as per the example above then connect the CDI output channels according to the table below. Cylinder Number CDI Output Channel CDI Output for Positive side of coil. for negative side of coil. 1 1 Pink/Black Red/White 5 2 Orange/Black Red/Yellow 3 3 Grey/Black Red/White 6 4 Yellow/Black Red/Yellow 2 5 White/Black Red/White 4 6 Blue/Black Red/Yellow Page 6
7 How to fire 2 channels together When you need to fire 2 channels at once then it is important to fire an odd and even channel together. In this way the CDI will discharge one capacitor for each coil being fired ensuring maximum energy to each coil. How to wire the output channels for a rotary A rotary engine fires a leading sparkplug and a trailing sparkplug very close together, its almost like firing 2 channels together. The leading coils of a rotary engine must be connected to an odd numbered channel and the trailing coils to an even numbered channel. This ensures that the leading plug uses one capacitor bank and the trailing plug uses the other. It is also important to use the odd numbered channels for the leading sparkplug because of the way the capacitors are charged in rotary mode. How to discharge 2 capacitors into one coil The EMS Dual Fire CDI system uses 2 charge capacitors, one for the odd numbered outputs and one for the even numbered outputs. Bridging one of the red/white wires with one of the red/yellow wires will cause the system to discharge both capacitors into one coil. This will give a longer lasting, hotter spark but at a reduced voltage. Overheat protection CDI systems provide high levels of electrical energy to the sparkplug coils. This means that high levels of current are drawn by the system, and like all high current devices, they can get hot. Although the Dual Fire CDI systems are able to deliver high energy levels for long periods of time, they can still overheat. If the system becomes too hot it will reduce the power output to a level where the system will start to cool down. Once a safer temperature is reached the system will resume full power again. Tacho output (brown/blue wire) This wire provides a 13.8 volt square wave output compatible with most tachos. Page 7
8 Operation modes The Dual Fire CDI system can be programmed to operate in different modes by either connecting the relevant wire to ground or leaving it unconnected. Rotary Mode (brown/yellow wire) Leaving this wire unconnected will put the CDI into piston engine mode. Connecting it to ground will put the CDI into rotary engine mode. Rotary engines have a leading and trailing sparkplug for each rotor. These can be fired simultaneously or the trailing just after the leading plug. For this reason you must connect the trailing plugs to an even numbered channel and the leading to an odd numbered channel. The system must also charge the discharge capacitors in a different manner to piston engines. Trigger Edge (brown/white wire) Leaving this wire unconnected will cause the CDI to fire each output on a falling input signal. Connecting it to ground will cause the CDI to fire each output channel on a rising input signal. All CDI systems have a delay time between the input channel signal and the output channel signal. This is mainly caused by the noise filtering circuit for each input. The Dual Fire CDI has a 28 microsecond delay for rising edge triggering and a 68 microsecond delay for falling edge trigger inputs. Most high-end after market ECUs such as EMS Motorsport ECUs have an ignition delay compensation adjustment that can be set to cancel this delay. IT IS VERY IMPORTANT TO SET THE TRIGGER EDGE ON THE CDI SYSTEM TO MATCH THE ECU SETTING. FAILING TO DO THIS MAY DAMAGE THE ENGINE. Power Select (brown/pink wire) Leaving this wire unconnected will cause the CDI to operate in low power mode. Connecting it to ground will cause the CDI to switch to high power. By connecting this wire to the auxiliary output of an ECU you can program it to switch the CDI between high and low power automatically in real time as needed. IE: Switch to high power mode when the engine is under heavy load. The power specifications table shows the power output for different mode and power settings Mode Select (brown wire) Leaving this wire unconnected will cause the CDI to operate in circuit racing mode. Connecting it to ground will cause the CDI it to operate in drag racing mode. In drag racing mode the CDI will deliver up to 570 volts to the coil. This can only be sustained continuously for about 3 minutes at 714 hertz before the CDI starts to cut back power to prevent over heating. This gives plenty of time to finish the race. In circuit racing where the engine is running at high RPM for extended periods of time this wire must be left unconnected. In this configuration the CDI is able do deliver up to 470 volts for very long periods of time at 714 hertz before its temperature becomes too high. Page 8
9 Specifications Maximum operating frequency: 714 hertz. Delay on rising trigger edge: 28 microseconds. Delay on falling trigger edge: 68 microseconds. Power Specifications Table Separated Banks Bridged Banks Circuit Mode Voltage Current Mili Joules Voltage Current Mili Joules Low Power High Power Drag Mode Low Power High Power The following output power and voltages are achieved with the battery voltage held at 13.8 Volts Page 9
10 EMS Computers Dual Fire Pin Description 1 Ground Black Ground 2 Ground Black Ground 3 Input 8 (8 Channel only) Violet Trigger signal 4 Input 6 (6 & 8 Channel only) Blue Trigger signal 5 Input 4 Yellow Trigger signal 6 Input 2 Orange Trigger signal 7 Input 7 (8 Channel only) Green Trigger signal 8 Input 5 (6 & 8 Channel only) White Trigger signal 9 Input 3 Grey Trigger signal 10 Input 1 Pink Trigger signal V Power Red Ignition 12 Volts V Power Red Ignition 12 Volts 13 Coil Output 1 Pink/Black Neg. Coil Rotary Mode Brown/Yellow Ground this wire for Rotary mode 17 Trigg Edge Select (Rise/Fall) Brown/White Ground this wire for rising trigger. edge. 18 Power Select (High/Low) Brown/Pink Ground this wire for high power. Can be connected to ECU Aux output 19 Tacho Output Brown/Blue Square wave output Mode Select (Drag/Circuit) Brown Ground this wire for drag mode Output 8 (8 Channel only) Violet/Black Neg. Coil 25 Output 3 Grey/Black Neg. Coil 26 Output 5 (6 & 8 Channel only) White/Black Neg. Coil 27 Output 7 (8 Channel only) Green/Black Neg. Coil 28 Coil + for odd outputs Red/White Pos. coil for channels 1,3,5,7 29 Coil + for odd outputs Red/White Pos. coil for channels 1,3,5, Coil + for even outputs Red/Yellow Pos. coil for channels 2,4,6,8 33 Coil + for even outputs Red/Yellow Pos. coil for channels 2,4,6,8 34 Output 2 Orange/Black Neg. Coil 35 Output 4 Yellow/Black Neg. Coil 36 Output 6 (6 & 8 Channel only) Blue/Black Neg. Coil Page 10
11 Drawings Socket view Socket is viewed from the back. Page 11
12 4 cylinder example Page 12
13 6 cylinder example Page 13
14 8 cylinder example Page 14
15 Rotary 3 coil example Page 15
16 Rotary 4 coil example Page 16
PLATINUM SERIES. Haltech. High Power Igniter Module QUICK START GUIDE. 4 Channel - # HT Channel - # HT Channel - # HT020040
PLATINUM SERIES Haltech High Power Igniter Module QUICK START GUIDE 4 Channel - # HT020032 6 Channel - # HT020036 8 Channel - # HT020040 HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL:
More informationMSD Circle Track LS Ignition Control PN 6014CT
MSD Circle Track LS Ignition Control PN 6014CT ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and
More informationMSD Blaster Ignition PN 5900
MSD Blaster Ignition PN 5900 Note: Read these instructions completely before attempting any installation. Parts Included: 1 - Blaster Ignition, PN 5900 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground
More information3-Stage Retard PN 8970
3-Stage Retard PN 8970 IMPORTANT: Read the instructions before attempting the installation. Parts Included: 1-3-Stage Retard Control 4 - Mounting Screws 4 - Mounting Grommets 6 - Retard Modules, 2, 3,
More informationMSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219
INSTALLATION INSTRUCTIONS MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 Parts Included: 1 - Ignition 1 - Wiring Harness 1 - Parts Bag 1 - CD ROM WARNING: When installing the SB6, disconnect
More informationMSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011
MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with
More informationProMaster Ignition Coil PN 29440
ProMaster Ignition Coil PN 29440 Parts Included: 1 - Ignition Coil 1 - Ignition Coil Bracket 1 - Screw, #10 x 1" 1 - Coil Wire Boot 1 - Coil Wire Terminal 2 - Ring Terminals 3 - Screws, #10 x 3/4" GENERAL
More informationMSD Pro Mag Information
MSD 44 Amp Pro Mag Generator Clockwise Rotation - PN 8130, PN 81303, PN 81305, PN 81307 Counterclockwise Rotation PN 8140, PN 81403, PN 81405, PN 81407 Parts Included In This Kit: 1 44 Amp Pro Mag Generator
More informationMSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011
MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 Parts Included 1 - Ignition Controller, PN 6011 1 - Pro-Data+ Software CD 1 - Harness 1 - Parts Bag 1-2-Bar MAP Sensor Optional Accessories
More informationBefore continuing with the installation, here are a few definitions you should be aware of:
MSD Ford Billet Distributors PN 8473: 2.3L, PN 8580: 351C, 351M, 400, 429, 460 PN 8582: 289, 302, PN 8584: 351W PN 85805: 351W w/edelbrock Victor Jr. Intake Important: Read these instructions before attempting
More informationMSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020
INSTALLATION INSTRUCTIONS 1 MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 Important: Read these instructions before attempting this installation! Parts Included: 1 - MSD Stacker Ignition
More informationMSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010
MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 Parts Included 1 Ignition Controller, PN 6010 1 Pro-Data+ Software CD 1 Harness 1 Parts Bag 6 Timing Modules Optional Accessories
More informationPLATINUM Sport Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE
PLATINUM Sport 2000 Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System
More informationMSD-8 Plus Ignition PN 7805
MSD-8 Plus Ignition PN 7805 Note: Solid Core spark plug wires cannot be used with an MSD Ignition. Parts Included: 1 - MSD-8 Plus Ignition 1 - Mag Pickup Extension Harness, PN 8860 4 - Vibration Mounts
More informationMSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012
MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty
More information3-Stage Retard PN 8970
3-Stage Retard PN 8970 IMPORTANT: Read the Instructions before attempting the installaiton. Parts Included: 1-3-Stage Retard Control 4 - Mounting Screws 4 - Mounting Grommets 6 - Retard Modules, 2, 3,
More informationMSD Start/Retard Control PN 8982
MSD Start/Retard Control PN 8982 IMPORTANT: Read the instructions before attempting installation. Parts Included: 1 - Start/Retard Control, PN 8982 4 - Retard Modules, 0, 2, 3, 4 1 - Wiring Kit 4 - Mounting
More informationPLATINUM. Sport Haltech 13B Terminated Engine Harness QUICK START GUIDE
PLATINUM Sport 1000 Haltech 13B Terminated Engine Harness QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com
More informationMSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251
MSD Kawasaki Jet Ski 750 Enhancer CD Ignition PN 4251 Parts Included: 1 - MSD Enhancer CD Ignition 2-6mm Stainless Steel Flatwashers 2 - Zip Ties Supplies Required For Installation 1 Tube of Blue Loctite
More informationMSD-8 Plus Ignition PN 7805
MSD-8 Plus Ignition PN 7805 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team
More information10 Ch Peak & Hold Injector Driver PN
Installation Instructions 10 Ch Peak & Hold Injector Driver PN 30-2710 WARNING: installation is not for the electrically challenged! Use this product with extreme caution! If you are uncomfortable with
More informationPLATINUM Series Haltech
PLATINUM Series Haltech Thermocouple Amplifier TCA 2 (HT059920 / HT059921) ( A / B ) TCA 4 (HT059940 / HT059921) ( A / B ) QUICK START GUIDE LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants
More informationMSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013
MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013 Parts Included: 1 - Ignition Controller, PN 6013 1 - Pro-Data+ Software CD 1 - Parts Bag 1 - Mounting Template Optional Accessories: Hand
More informationMSD Zero-Cross Distributor Chevrolet - PN 83971
MSD Zero-Cross Distributor Chevrolet - PN 83971 Parts Included: 1 Distributor 1 Gasket 1 Hold Down & Hardware 1 Gear Lubricant 2 O-Rings IMPORTANT The Separate Pickup Zero-Cross Distributors use two completely
More informationInstallation Instructions for the Lingenfelter TBRC-001 Temperature Based Relay Controller
Installation Instructions for the Lingenfelter PN: L460220000 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761 fax www.lingenfelter.com Revision
More informationREMOTE CENTRAL LOCK. Model: CLRxxx-ULT
REMOTE CENTRAL LOCK Model: CLRxxx-ULT Contents Remote Lock, Remote Unlock, Car Finder, Remote Boot release:, Power Window outoput, Learning Transmitter Codes... page 3 Wiring Diagram... page 4 Introduction,
More informationMSD 7AL-3, Ignition Control PN 7230
MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,
More informationMSD Programmable Shift Controller PN 7559
MSD Programmable Shift Controller PN 7559 WARNING: During installation, disconnect the battery cables. When Disconnecting, always remove the Negative cable first and install it last. Parts Included: 1
More informationMSD Marine Ignitions 6M-2L, PN 6560
MSD Marine Ignitions 6M-2L, PN 6560 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD
More informationMSD Single Cylinder Programmable Ignition PN 4217
MSD Single Cylinder Programmable Ignition PN 4217 Parts Included: 1 - PN 4217 1 - PN 4217 Wire Harness 1 - CD Rom 9609 1 - Parts Bag 1 - Serial Cable WARNING: During installation, disconnect the battery
More informationCUSTOMER WIRING INSTRUCTIONS TO SUIT: BA-BF XR6 and XR8 Universal Auto or Manual Trans
, CUSTOMER WIRING INSTRUCTIONS TO SUIT: BA-BF XR6 and XR8 Universal Auto or Manual Trans Lay the C.A.E Engine loom in vehicle and plug in all the sensors. ( The sensor plugs can only be connected one way
More informationACCEL SUPER BOX P/N 61212
FRM 34395 INSTALLATION INSTRUCTIONS ACCEL SUPER BOX P/N 61212 PARTS INCLUDED: (x1) Ignition (x1) 18 Ground Wire (x4) Mounting Screws (x1) Harness (x1) 100V/1A Diode WARNING! During installation, disconnect
More informationManual - FTSPARK v3 - Capas ENUS.pdf 1 2/16/2017 6:06:34 PM C M Y CM MY CY CMY K OWNER S MANUAL
OWNER S MANUAL Index 1. Presentation...4 2. Characteristics...5 3. Warranty terms...6 4. Installation...7 4.1 Mounting...7 4.2 Power supply...7 4.3 Harness connections table...8 4.4 Wiring harness installation...
More informationMSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue
More informationMSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740
MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issued with
More informationMSD Circle Track Ignition PN 6427
MSD Circle Track Ignition PN 6427 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD
More informationELITE 1000/1500 Dodge SRT QUICK START GUIDE HT
E N G I N E M A N A G E M E N T S Y S T E M S ELITE 1000/1500 Dodge SRT4 03-05 QUICK START GUIDE HT-140940 LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the HaltechTM Programmable Fuel Injection
More informationInstallation Instructions for the Lingenfelter Fan and Pump Manual Override Kit
Installation Instructions for the Lingenfelter Fan and Pump Manual Override Kit PN: L300180000 v1.1 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761
More informationMSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor 1 - Rotor,
More informationAccuSpark. Fitting and Information Guide For. Modules Distributors coils Tools. Modern Ignition for Classic cars
AccuSpark Modern Ignition for Classic cars Fitting and Information Guide For Modules Distributors coils Tools www.accuspark.co.uk 1 Before fitting AccuSpark Distributors AccuSpark electronic ignition kit.
More informationMSD Digital 6M-3L Marine Ignition PN 6564
MSD Digital 6M-3L Marine Ignition PN 6564 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps
More informationMSD Pro-Billet Ford FE Distributor PN 8594
MSD Pro-Billet Ford FE Distributor PN 8594 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition is required with this Distributor. Parts Included: 1 - Pro-Billet
More informationMSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN Extra Tall, PN 8547 with Locked-Out Timing, PN 85501
MSD Pro-Billet Chevrolet V8 Distributor with Slip Collar, PN 85561 Extra Tall, PN 8547 with Locked-Out Timing, PN 85501 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product
More informationPLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 QUICK START GUIDE (HT & HT059980) Version 4
PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 (HT059970 & HT059980) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH:
More informationLingenfelter TMR-001 Timer Delay Control Module
Lingenfelter TMR-001 Timer Delay Control Module PN: L460290000 Revision - 1.1 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761 fax www.lingenfelter.com
More informationMaxxECU quickstart guide ( )
Be a tuning mastermind. Like us. MaxxECU quickstart guide (2019-02-01) Online help! maxxecu.com/support Wiring diagrams Installation help Pinout Support maxxecu.com/support Legal disclaimer All performance
More informationPERTRONIX DIGITAL HP INSTALLATION INSTRUCTIONS
PERTRONIX DIGITAL HP INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Specifications... 4 General Information... 5 Coil Compatibility... 6 Mounting the Digital HP... 7 Wiring... 8 User Interface... 12 Programming...
More informationMSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor
More informationMSD Billet Distributor Buick V6 Even-Fire PN 8551
MSD Billet Distributor Buick V6 Even-Fire PN 8551 Important: Read these instructions before attempting the installation. Parts Included: 1 - Billet Distributor 1 - Rotor, PN 8467 1 - Distributor Cap, PN
More information12-Volt Negative Ground Installation Instructions
12-Volt Negative Ground Installation Instructions For Part Number: 1183 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for 12-Volt negative
More informationMSD Pro-Billet Chevrolet HEI Distributor PN 8365
MSD Pro-Billet Chevrolet HEI Distributor PN 8365 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor, PN 8365 1 - Rotor, PN 84101 1 - Distributor
More informationMSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor
More informationADVANCED KEYLESS ENTRY SYSTEM INSTALL GUIDE.
REV.2009.04.10 KE-6 ADVANCED KEYLESS ENTRY SYSTEM TM INSTALL GUIDE www.ultrastarters.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
More informationMSD Pro-Billet V8 Distributor Buick 400, 430, 455, PN 8517 Buick 215, 300, 340, 350, PN 8548 Oldsmobile, PN 8566 Pontiac, PN 8563
MSD Pro-Billet V8 Distributor Buick 400, 430, 455, PN 8517 Buick 215, 300, 340, 350, PN 8548 Oldsmobile, PN 8566 Pontiac, PN 8563 Important: Read these instructions before attempting the installation.
More informationMallory HyFire Electronic Ignition Control
Mallory HyFire Electronic Ignition Control PN 690 Parts Included: 1 - Ignition 1 - Harness, Mag Pickup 1-18" Ground Wire 1-100V/1A Diode 4 - Mounting Screws WARNING: During installation, disconnect the
More informationMSD Pro-Billet Front Mount Ford Flathead Distributor 2-Bolt, , PN Bolt, , PN 8353
MSD Pro-Billet Front Mount Ford Flathead Distributor 2-Bolt, 1942-1948, PN 8351 3-Bolt, 1932-1941, PN 8353 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help
More informationThis is to be wired to the start position on the ignition switch. If using an Automatic gearbox, wire this up through the inhibitor switch first.
Lay the C.A.E Engine loom in vehicle and plug in all the sensors. ( The sensor plugs can only be connected one way ). Mount the C.A.E Control Loom with the relays and circuit breakers to passenger side
More informationQuick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink.
Quick Start Guide This is only a quick start guide. A full wiring and installation manual is included in PCLink. Installer I/O Table Wire Description Installer Connection Typical Application +14V Bat Full
More informationMSD Pro-Billet Chrysler V8 Distributor PN , 400 PN , 440
MSD Pro-Billet Chrysler V8 Distributor PN 8545-383, 400 PN 8546-426, 440 Important: Read these instructions before attempting the installation. Note: An MSD Ignition Control is required to use these distributors.
More informationLingenfelter ECSS-001 Ethanol Content Sensor Signal Simulator Installation & Operating Instructions
Lingenfelter ECSS-001 Ethanol Content Sensor Signal Simulator Installation & Operating Instructions PN: L460350085 Revision - 1.6 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733
More informationINSTALLATION INSTRUCTIONS FOR PRO-16B S3 6 CHANNEL CAPACITOR DISCHARGE IGNITION
INSTLLTION INSTRUTIONS FOR PRO-6 S 6 HNNEL PITOR ISHRGE IGNITION PLESE REPORT NY OMISSIONS OR ERRORS TO SLES@MWIGNITIONS.OM ONTENTS:. Installation notes. Ignition coil information. Mounting dimensions.
More informationMSD Pro-Billet Chevrolet HEI Distributor PN 8365
MSD Pro-Billet Chevrolet HEI Distributor PN 8365 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering
More informationMSD LS Ignition Control PN 6014/60143
MSD LS Ignition Control PN 6014/60143 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the
More informationMSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393
MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor, PN 8360 Chevrolet 348, 409 Distributor, PN 8393 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly
More informationMSD DIS-2 Plus Ignition PN MSD DIS-4 Plus Ignition PN 62152
MSD DIS-2 Plus Ignition PN 62112 MSD DIS-4 Plus Ignition PN 62152 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with
More informationMSD Pro-Billet Flat-Top Chevrolet V8 Distributor PN 84891
MSD Pro-Billet Flat-Top Chevrolet V8 Distributor PN 84891 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product
More informationAUTO-BLiP. User Manual Chevrolet Corvette. Version 1.2
AUTO-BLiP INTELLIGENT DOWNSHIFTS www.auto-blip.com User Manual 1997-2004 Chevrolet Corvette Version 1.2 Copyright 2012 Tractive Technology, LLC. All rights reserved. Page 1 WARNING Use of the AUTO-BLiP
More informationFAST XIM. XIM Unit Installation
1 INSTRUCTIONS XIM Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to
More informationMSD Pro-Billet Chevrolet HEI Distributor PN 8365
MSD Pro-Billet Chevrolet HEI Distributor PN 8365 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and
More informationAUTO-BLiP. User Manual Porsche INTELLIGENT DOWNSHIFTS. Version 1.2
AUTO-BLiP INTELLIGENT DOWNSHIFTS www.auto-blip.com User Manual 2005+ Porsche Version 1.2 Copyright 2012 Tractive Technology, LLC. All rights reserved. Page 1 WARNING Use of the AUTO-BLiP while driving
More information8 Pin Female Plug. WIRING INSTRUCTIONS TO SUIT : Holden VT V6+V8
WIRING INSTRUCTIONS TO SUIT : Holden VT V6+V8 Lay the C.A.E Engine loom in vehicle and plug in all the sensors. (The sensor plugs can only be connected one way). Mount the C.A.E Control Loom with the relays
More informationMSD Pro-Billet Small Diameter Ford V8 Distributor PN 8577/85773; 351C-460, PN 8578/85783; 351W PN 8579/85793; 302
MSD Pro-Billet Small Diameter Ford V8 Distributor PN 8577/85773; 351C-460, PN 8578/85783; 351W PN 8579/85793; 302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product
More informationCMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION
CMD-4000 SERIES REV. A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION Thank you for purchasing the CMD-4000 series Remote Control Door Latch Opener System from Dakota Digital, Inc. This,
More informationStreet Fire CDI PN 5520
Street Fire CDI ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if
More informationMSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360
MSD Pro-Billet Ready-to-Run Chevrolet V8 Distributor PN 8360 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor
More informationUSER MANUAL AND INSTALLATION GUIDE ENGINE RPM AND NOS SHIFT COUNTER NOS DELAY TIME IN SECONDS NOS START PERCENT NOS FINAL PERCENT
SCHNITZ MOTORSPORTS DSC-9PS "PRO-STREET" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE SHIFT LIGHT POSITIVE PAGE 2 SHIFT LIGHT GROUND PAGE 2 NOS SOLENOID GROUND 1GA ORANGE, FUEL SOLENOID GROUND
More informationMSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570
MSD Pro-Billet Small Diameter Chevrolet V8 Distributor PN 8570 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your
More informationPro-14R 2 Rotor 115mJ Series 3
Pro-14R 2 Rotor 115mJ Series 3 pplicable S/No s 41xxxx ONTENTS: 2. Installation notes 6. Ignition coil information 7. onnections & Specifications 8. irect fire rotary ignition 9. irect fire reciprocating
More informationInstallation Instructions
Installation Instructions 8 Channel C 2 D Ignition System PN 30-2800 4 Channel C 2 D Ignition System PN 30-2801 WARNING: This installation is not for the electrically challenged! Use this ignition with
More informationMSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595
MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark
More informationMSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653
MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with
More informationMSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi
MSD Pro-Billet Ready-to-Run Chrysler Distributor PN 8391-331/354 Early Hemi PN 8389-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there
More informationGM Stepper Idle Adapter User Manual
GM Stepper Idle Adapter User Manual 30-3805-07 THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES ONLY AND SHOULD NEVER BE USED ON PUBLIC HIGHWAYS. AEM Performance Electronics AEM Performance Electronics,
More informationMSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302
MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your
More informationREDI-LINE. Rugged, Reliable, DC to AC Power Conversion ELECTRIC GENERATORS USER'S GUIDE. KARAM A.L.
REDI-LINE ELECTRIC GENERATORS USER'S GUIDE Rugged, Reliable, DC to AC Power Conversion KARAM A.L. www.alternatorstarter.com 1-888-515-2726 REDI-LINE ELECTRIC GENERATOR MODEL INPUT ACTUAL OUTPUT ACTUAL
More informationMSD Pro-Billet Chrysler V8 Distributor PN , 400 PN , 440
MSD Pro-Billet Chrysler V8 Distributor PN 8545-383, 400 PN 8546-426, 440 Important: Read these Instructions before attempting the installation. Note: An MSD Ignition Control is required to use these distributors.
More informationA) 8 Pin Female. CUSTOMER WIRING INSTRUCTIONS TO SUIT : Ford EL Manual Universal Instructions
CUSTOMER WIRING INSTRUCTIONS TO SUIT : Ford EL Manual Universal Instructions Lay the C.A.E Engine loom in vehicle and plug in all the sensors. ( The sensor plugs can only be connected one way ). Mount
More informationInstallation Instructions for: Channel Thermocouple Amplifier
Installation Instructions for: 30-2204 4 Channel Thermocouple Amplifier WARNING: This installation is not fo r the electrically or mechanically challenged! Use this sensor with EXTREME caution! If you
More informationA/C PRESSURE MONITOR INSTALLATION INSTRUCTIONS SYSTEM OPERATION GREEN INDICATOR LIGHT
A/C PRESSURE MONITOR INSTALLATION INSTRUCTIONS Do not attempt to clean or inspect anything while the engine is running. Cleaning and inspection must be done by a certified mechanic. All A/C service must
More informationMSD 7AL-2 Plus Ignition
MSD 7AL-2 Plus Ignition PN 7222/72223 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the
More informationSCHNITZ MOTORSPORTS USER MANUAL AND INSTALLATION GUIDE PRO-MOD BATTERY VOLTS DIAGNOSTICS NOS PULSE FREQUENCY NOS DELAY TIME IN SECONDS
SCHNITZ MOTORSPORTS DSC-CS "PRO-MOD" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE COIL, (OPTIONAL) GA YELLOW, COIL, NEGATIVE GA WHITE, GA BLACK, SHIFT LIGHT +V OUTPUT PAGE 0 NOS ACTIVATION INPUT
More informationV-TWIN HIGH-PERFORMANCE IGNITION SYSTEM 12 VOLT SYSTEM TYPE: PDV1
Smart ー Fire V-TWIN HIGH-PERFORMANCE IGNITION SYSTEM 12 VOLT SYSTEM TYPE: PDV1 Smart-Fire APPLICATIONS VINCENT 50 DEGREE V-TWINS & SIMILAR APPLICATIONS WITH 12-VOLT ELECTRICS, POSITIVE OR NEGATIVE EARTH
More informationPro-Drag4R 2 Rotor 250mJ S4
Pro-rag4R 2 Rotor 250mJ S4 ELETRIL WIRING & OPERTING INSTRUTIONS pplicable S/No s 89xxxx FILURE TO FOLLOW INSTRUTIONS WILL VOI WRRNTY ONTENTS: 2. Installation notes 6. onnections and specifications 7.
More informationDUAL LINEAR MOTOR / ACTUATOR CONTROLLER W/ CURRENT SENSING AUTO REVERSE
PAC-3200 DUAL LINEAR MOTOR / ACTUATOR CONTROLLER W/ CURRENT SENSING AUTO REVERSE PAC-3200 PRESET BUTTONS MOTOR 2 DUAL LINEAR MOTOR CONTROLLER WITH SAFETY REVERSE MOTOR 2 MOTOR 1 MAIN #1 ACC DISABLE #2
More informationAUTO-BLiP. User Manual Chevrolet Corvette. Version 1.7
AUTO-BLiP INTELLIGENT DOWNSHIFTS www.auto-blip.com User Manual 2008-2013 Chevrolet Corvette Version 1.7 Copyright 2012 Tractive Technology, LLC. All rights reserved. Page 1 WARNING Use of the AUTO-BLiP
More informationSCHNITZ MOTORSPORTS PNC-202, 2-STAGE PROGRESSIVE NITROUS CONTROLLER USER MANUAL AND INSTALLATION GUIDE NOS PULSE FREQUENCY
SCHNITZ MOTORSPORTS PNC-202, 2-STAGE PROGRESSIVE NITROUS CONTROLLER USER MANUAL AND INSTALLATION GUIDE NOS #2, FUEL SOLENOID(GROUND) 1GA PURPLE, PAGE 14 NOS #2 NITROUS SOLENOID(GROUND) 1GA PURPLE, PAGE
More information2 Way Security and Keyless Entry Installation Guide ca 1553
PROFESSIONAL SERIES 2 Way Security and Keyless Entry Installation Guide ca 1553 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More informationV8 Gen. V Ford Mustang 2010 Update
V8 Gen. V Ford Mustang 2010 Update There were several updates to the Ford Mustang in the 2010 model year. This document outlines the differences between the installation steps necessary for the 2010 Mustang
More informationMSD Pro-Billet Chrysler Distributor PN Early Hemi
MSD Pro-Billet Chrysler Distributor PN 83891-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your
More informationMSD Digital-7 Plus Ignition Control PN 7520
INSTALLATION INSTRUCTIONS MSD Digital-7 Plus Ignition Control PN 7520 Parts Included: 1 - MSD Ignition 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground Wire 1 - White Jumper 1 - Red Jumper 2 - Violet
More information